ZHUHAI WINGPOW EROTIC and NOVELTY 31415T Party in my pants User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1366217
Application ID	KAh3A3k2vLmJBd9+jCIGTA==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.63kB (82844 bits)
Date Submitted	2010-10-26 00:00:00
Date Available	2010-10-26 00:00:00
Creation Date	2010-10-19 11:15:33
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2010-10-19 11:15:33
Document Title	Users Manual
Document Creator	PScript5.dll Version 5.2.2
Document Author:	aov

Introduction to Design Plan of Transmitter
Transmitter
LED display
Antenna
4F functional
button
ON/OFF button
Operating Principle
•
Master Control Chip conducts data analysis and identification on button
demand through button scan. Analog signal will be converted to digital
signal through A/D Converter, and corresponding code signal will be
output following operation.
•
After the user’s button demand is processed to code signal , the code
signal will be loaded to high-frequency local oscillator signal by
frequency mixing so as to form radio-frequency signal satisfying
requirement of transmission.
•
Code signal is loaded to radio-frequency signal and is transmitted to
surrounding environment by antenna via transmission circuit, in order to
control action of receiver.
Logic Block Diagram
Status
display
Functional
button circuit
Master Control Chip
Signal Processing Unit
A/D Converter and code
output
Voltage stabilization and
filtering
Transmission
antenna
Output of RF carrier
signal
Code
signal
12V battery as
power supply
Modulation of highfrequency local oscillator
433.92M Quartz
Crystal Local
Resonator
Electric Parameters and Properties
• Voltage of power supply：23A battery, 12VDC
• Transmission amplitude ：
Principal wave
+17DB
Secondary harmonic -18DB
• Transmission frequency：433.92MHZ （+/20PPM）
• Modulation model：AM
Application Method
•
•
•
•
•
•
•
Press Start button of receiver, and the system starts in ready
mode ；
Long press ON/OFF button for 3 seconds, the product will work in
F1 mode and start vibration；
Press 4F button of remote-controller, the product will work in F2
mode and accelerate vibration；
Press 4F button of remote-controller again, the product will work in
F3 mode and vibrate at the highest speed；
Press 4F button of remote-controller again, the product will work in
F4 mode and pulse vibration mode. The four modes may change
from F1 to F4 repeatedly.
Long press ON/OFF button for 3 seconds again, the product will
turn off and stop work；
Red light of LED can be seen while pressing button.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not causeharmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
hanges or modifications not expressly approved by the party responsible for
compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : aov
Create Date                     : 2010:10:19 11:15:33+08:00
Modify Date                     : 2010:10:19 11:15:33+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Title                           : <4D6963726F736F667420506F776572506F696E74202D20B7A2C9E4C6F7C9E8BCC6B7BDB0B8A3A8D6D0D2EBD3A2A3A92E707074>
Creator                         : aov
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:0935fbc0-9e8b-4892-bf5a-b32569dc5b01
Instance ID                     : uuid:ba62a4c0-3b26-4727-bc8b-27accf4f3ee3
Page Count                      : 7

EXIF Metadata provided by EXIF.tools