ZINUS ZM1000 Bed remote control User Manual
ZINUS(Xiamen) Co., Ltd Bed remote control Users Manual
ZINUS >
User Guide
The JCYK-09-3 Remote Handset Use Manual
The position of S1-S10 button on the operation panel as following:
S1 Save
Ysection
Zsection
Xsection
S10 actuator/massage motor selection
S2 Up
S3 select motor towad left S4 select motor toward right
S5 Down
S6 Save1
S7 Save2
S8 Save3
S9 Save4
Introduce the use of the JCYK-09-3 remote handset in details:
At first, we should divide the LED into three parts:Xsection,Ysection and
Zsection.As indicated above.
1. When power on, all the actuators reset to keep the bed in FLAT.(If the RESET
couldn’t finished normally, it is possibly the battery supply power to controller. Here,
we can take the battery fuse which on the top of the controller case down in order to
finish the Reset.)
2. Move the push-button S10 to “B”, then press S3 or S4 to lighten X section of LED.
At this moment, Press S2 continuously, the bed HEAD move up: loosen it, the bed
HEAD stop moving.
Press S5 continuously, the bed HEAD move down: loosen it, the bed HEAD stop
moving.
When in the process of M1, press the safety switch L1, M1 stop falling. loosen the
safety switch,M1 Continue to decline .
3. Move the push-button S10 to “B”, then press S3 or S4 to lighten Y section of LED.
At this moment,Press S2 continuously, the bed BUTT move up, loosen it, the bed
BUTT stop moving.
Press S5 continuously，the bed BUTT move down: loosen it, the bed BUTT stop
moving.
When in the process of M2, press the safety switch L2, M2 stop falling. loosen the
safety switch,M2 keep on stopping .
4. Move the push-button S10 to “B”, then press S3 or S4 to lighten Z section of LED.
At this moment,Press S2 continuously, the FEET part move up after flated then
drive KNEE up in bend state, loosen S2, the bed stop moving.
Press S5 continuously, the KNEE move down to flat bed, then move down bed FEET.
loosen S5, bed stop moving. During this course the foreside of bed should keep a
certain distance with the ground in order to make sure the bed can work safely and
credibility.
5. Move the actuator, when it move to a certain state, press S1,then press S6, the
position will be memorized. Wherever the motor move, press S6, the motor move
to the position kept just. Press S1 and then press S6 when the motor move to
another place,the position of S6 will be changed. When restart ,memory position is
the new location. The usage of S7，S8，S9 is same with S6.
6. Move the key-press S10 to “M”,then press S3 or S4 to lighten X section of LED.
At this moment,Press S2,the massage motor 1 start vibration,press again, the intensity
of motor boost up.Press S5 the intensity of motor weaken. The motor have 5 different
intensity.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Statements from 15.105 and 15.21
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment
authority to operate this equipment.