ZIONCOM ELECTRONICS IP04223 150Mbps Wireless N Portable AP User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2448244
Application ID	vPEbCvlJtXyYZ67Unrd96Q==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	40.01kB (500104 bits)
Date Submitted	2014-11-18 00:00:00
Date Available	2014-11-19 00:00:00
Creation Date	2013-05-10 10:37:26
Producing Software	3-Heights(TM) PDF Producer 4.4.36.0 (http://www.pdf-tools.com)
Document Lastmod	2014-11-19 03:08:49
Document Title	iPuppy III(IP04223)英文说明书
Document Creator	Adobe Illustrator CS5

Hardware Installation
Quick Installation Guide
Ports and Buttons
150Mbps Wireless Pocket AP
Ports and Buttons
MODEL：iPuppyⅢ
WPS/Rst
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Description
Press this button for 2-3 seconds, the power LED indicator keeps solid
light, it is WPS working. If press for about 10 seconds, the device will
restore to factory settings.
This port is used for power-in
NOTE: the charging wire we provided can only be used for charging,
data transmission not supported.
Micro USB
Power in
This port connects the AP to Internet.
2 -b
2 -a
Router/AP
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with
Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and
the antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and
installers must be provide with antenna installation instructions and consider removing the no-collocation statement.
This slide switch allows users to switch device mode between Router
& AP.
LED Indicators
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
LED Indicators
Description
This LED indicator lights orange when this device gets power.
When there is WLAN connection, this indicator blinks orange.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated
This LED indicator lights orange when it is connected and working.
with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
● The default Network Name (SSID): TOTOLINK iPuppy III
● Password: TOTOLINK
Co p y ri g h t s 2 0 1 3 by T O T O L INK All righ ts res erv ed. Webs ite: h ttp://www.t ot olink .net
Information in this document is subject to change without prior notice.
Working Modes
AP Mode
Router Mode
In this mode, you can access Internet by just two steps.
Repeater
This mode makes iPuppy III work like a wireless router. It supports
three methods to access Internet: DHCP/PPPoE/Static IP.
For example, if you connect Internet by modem, you will have to:
This function allows iPuppy III to get wireless signals from other router or AP. Sometimes, the wireless signal your PC gets is very weak
because of distance. Then you can use the repeater of iPuppy III to solve this problem. Please follow below steps to setup repeater function:
Click Scan AP, it will pop up a window requiring you to choose one
Repeater Network Name.
Login to Setup interface of this device to make it connect Internet successfully
(Please refer to Section 3 Configure Router.)
2 -b
2 -b
2 -a
2 -a
Internet
Go to Wireless—Wireless Multibridge to set your repeater parameters.
See below:
TOTOLINK N100RE
ADSL Modem
Choose the right one and click Select AP. It will turn back to Multibridge
page which shows you some information of this SSID:
TOTOLINK N100RE
Network
Cable
Network
Cable
Connect your Modem and iPuppy III using network cable.
Connect iPuppy III to PC or Power Adapter using provided USB cable.
Go to Setup interface of this device to make it connect Internet successfully
(Please refer to Section 3 Set up AP).
Plug existing network cable into the LAN/WAN port of iPuppy III.
Connect iPuppy III to PC or Power Adapter using provided USB cable.
Now, you can search for the SSID of iPuppy III and enter the password
(By default, it is TOTOLINK) to access Internet. Generally, this mode is applied
in hotels, restaurants and small offices.
After correct configuration, you can search for the SSID and enter the password
(By default, it is TOTOLINK) to access Internet. This mode is mostly applied at home
and in student hostels.
Then you can set the encryption for this connection and click Apply to
make the repeater operation work.
If you want to change the SSID and password of this device, you
must connect to it in Router Mode (Please refer to Part 3- ).
Wireless Network Connection
Configure Router
Please set up the router following the below steps.
Run the Web browser.
PC connect to iPuppy III
DHCP (you don’t need to do any configuration.)
The network ‘TOTOLINK iPuppy III’ requires a network key (also called a WEP key or WPA key).
A network key helps prevent unknown intruders from connecting to this network.
TOTOLINK iPuppy III
TOTOLINK iPuppy III
Static IP
Right-click “My Network
Places”, click “Properties”
Input the encrytion key and click “Connect”
Type 192.168.1.1 in the Web browser address bar, then press Enter.
Confirm the wireless network SSID name,
choose one that you would like to connect,
then click “Connect”
TOTOLINK iPuppy III
Input User Name and Password, then click “OK”.
(the default User Name and Password are “admin”.)
PPPoE
Right-click “Wireless Network
Connection”, and click “View
Available Wireless Networks”
Have connected wireless network, you can
access Internet through wireless mode.
Android Phone connect to iPuppy III
Wireless Wizard
Choose Settings.
Click Wi-Fi.
Please choose
TOTOLINK iPuppy III.
Click Connect.
It shows Connected below
the SSID. You have connect
to iPuppy III successfully.
Click Setup Wizard.
TOTOLINK iPuppy III
TOTOLINK iPuppy III
TOTOLINK iPuppy III
TOTOLINK N151RA
TOTOLINK N151RA
TOTOLINK N301RA
TOTOLINK N301RA
After you set the Encryption key, please remember your Network Name (SSID)
and the Encryption key to connect with your wireless LAN.
Internet Configuration Wizard.
With iPuppy III powered on, press the WPS/Rst button for 2-3
seconds, the Power LED indicator changes to solid lighting,
it is WPS working. For about 10 seconds, it is Reset working,
the AP will reboot to factory default settings.
iPhone connect to iPuppy III
Choose Settings.
Choose WLAN.
Choose TOTOLINK
iPuppy III.
Enter password of this SSID,
by default, it is TOTOLINK.
Click Join.
There is a tick before TOTOLINK
iPuppy III, you have connected to
this AP successfully.
Enter the password for “TOTOLINK iPuppy III ”
Access Internet Mode Judgement Method
Internet Access Mode
Parameters that provided by ISP (Service Provider)
ISPs do not provide any parameters, you can access Internet
without router, no need set up the PC.
DHCP(Cable)
Static IP
Fixed IP address, Subnet mask, Default gateway and DNS server
PPPoE
User name & Password.
For more information, please go to www.totolink.net
TOTOLINK N151RA
TOTOLINK N151RA
TOTOLINK iPuppy III
TOTOLINK iPuppy III
TOTOLINK N301RA
TOTOLINK N301RA
Zion
Zion

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Create Date                     : 2013:05:10 10:37:26+09:00
Creator                         : Adobe Illustrator CS5
Title                           : iPuppy III(IP04223)英文说明书
Modify Date                     : 2014:11:19 03:08:49Z
Producer                        : 3-Heights(TM) PDF Producer 4.4.36.0 (http://www.pdf-tools.com)
Page Count                      : 1

EXIF Metadata provided by EXIF.tools