ZKC Software Technology PDA3501 Android handheld terminal User Manual PDA3501
Shenzhen ZKC Software Technology Co.,Ltd Android handheld terminal PDA3501
User Manual
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
2. Power on/off
Power on: Please put the battery right before power on the device(the battery is
put opposite while shipping). Long press the power key to start.
Power off: Long press the power key and click “power off”.
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
3. Barcode, Qrcode Scanner
3.1 Camera scanner(scan barcode and Qrcode)
Open the “ZbarScan” App, then press “scan” key to scan(the scanning
distance have to be within 10cm ).
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
When the “barcode scanner” App run on the backend, it can scan any barcode
in any input box.
For example, open the message input box, and press the “scan” key, the
barcode number will show as below:
3.3 Qrcode scanner(scan barcode and Qrcode)
Same as laser barcode scanner, please refer to 3.2.
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
Note 1: If the device can not use input box to scan barcode, please confirm
that whether the “barcode scanner” App run on the backend, or whether the
soft keyboard is “English(United States)”.
Setting---Language&input-----English(United States)
Note 2: If you can see red line when scan barcode (or QR code ),but no beep
and can not get barcode(or QR code) number on the screen , pls setting as
below:
For laser barcode version device, press”barcode modules set”,than
press”Restore Factory Settings”,press”Setting Data Format”,do not exit the
setting page and try to scan barcode,try this once more if still not get barcode.
For QR code scanner version,press Qr modules set,than press”Restore
Factory Settings”,press”Setting Data Format”.
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
6. 3G Test
Insert into the 3G card to the slot and power on the device.
Click “Change” and select “data connection”, then click “SIM2” as below:
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
1. Use careful with the earphone maybe possible excessive sound pressure from
earphones and headphones can cause hearing loss.
2. CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
3. The product shall only be connected to a USB interface of version USB2.0
4. Adapter shall be installed near the equipment and shall be easily accessible.The plug
considered as disconnect device of adapter(Manufacturer : SHENZHEN VICO-BO
TECHNOLOGY CO.,LTD. Travel Charger Model: WKB0502-002 Input: 100-240V~,
50/60Hz,300mA; Output: 5V, 2A)
5. Extreme temperature: 40℃
6. The plug considered as disconnect device of adapter
7. The device complies with RF specifications when the device used at 0cm form your
body
8. Declaration of Conformity
Hereby, Shenzhen ZKC Software Technology Co.,Ltd
declares that this Android handheld terminal product is in compliance with essential
requirements and other relevant provisions of Directive 1999/5/EC. A copy of the
Declaration of conformity can be found at www.sznewbest.com
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction
This Android handheld terminalmeets the government's requirements for exposure to
radio waves. The guidelines are based on standards that were developed by
independent scientific organizations through periodic and thorough evaluation of
scientific studies. The standards include a substantial safety margin designed to assure
the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6
W/kg averaged over one gram of tissue. Device types: Android handheld terminal
(FCC ID:2AGEB-PDA3501) has also been tested against this SAR limit. The
highest SAR value reported under this standard during product certification for use at
the ear is 0.301W/kg and when properly worn on the body is 0.483W/kg. This device
was tested for typical body-worn operations with the back of the handset kept1cm
from the body. To maintain compliance with FCC RF exposure requirements, use
accessories that maintain a 1cmseparation distance between the user's body and the
back of the handset. The use of belt clips, holsters and similar accessories should not
Shenzhen ZKC Software Technology Co.,Ltd
Web: www.sznewbest.com
Address: 1st Floor, No. 1 Block, Zhongkenuo Industry Park, Beiqi Road, Xixiang Town, Bao'an District,
Shenzhen
contain metallic components in its assembly. The use of accessories that do not satisfy
these requirements may not comply with FCC RF exposure requirements, and should
be avoided.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure
requirements, a minimum separation distance of 0 cm must be maintained between
the user’s body and the handset, including the antenna. Third-party belt-clips, holsters,
and similar accessories used by this device should not contain any metallic
components. Body-worn accessories that do not meet these requirements may not
comply with RF exposure requirements and should be avoided. Use only the supplied
or an approved antenna.