ZKTECO LH7500 Hotel Lock User Manual

ZKTECO CO., LTD. Hotel Lock

user manual

Installation GuideVersion: 1.0Date: Jan. 2019LH7500
1Lock DiagramBefore InstallationABDGCHOMEIJNFPKLRQEI
2IntheBox A N G LK SCOPEIUB M HF TDKM5*40PM4*20
3Beforeyou begin 1. Preparing doorNote: Please install the mortise (G) according to the above pictures. G GG GLeft hand, open inward Right hand, open inward2. Determining HandingDoor Thickness O Screws P Screws38 - 48 mm 40 mm 20 mmNote: If the door is thicker than 38-48 mm, this lock will not be available.StandpointLeft hand, open outward Right hand, open outwardThe hand of a door is determined from the secure side of the door. The term "secure" means the side from which you unlock and enter.
4Cautions1. New lock is defined as always open mode until it was unlocked once by mifare card.2. Please swipe authorised card, time sync card, room card at first for the new lock.3. The lock is equipped with mechanical keys for manual unlocking. Remove the mechanical keys from the package and keep them in a safe place.4. To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED. 5. Do not remove batteries when the lock is in working state.6. When battery power is low, the lock will beep to remind user to renew the batteries. Please do not mix up positive and negative while replacing battery.7. Avoid contacting with corrosive substances, and do not hang objects on the handle.8. The software within the lock manages the RFID cards, for more details refer to the software user manual.9. If there are any questions, please do not hesitate to contact the seller.
5 Installation desired handle heightcenter line of the handledoor thickness 38~48 mmbackset 54 mm2. Remove the mortise latch plate1. Drill holes on the doorNote 1: Align the template along the vertical center line of the mortise (G) at the desired handle height, and tape it to door.Note 2: Mark the holes first, then start drilling.GJ
63. Install mortise(G) and cylinder(F)FFHHGH
74.Install the coil spring and screw th stud eBBDAACUUAM
85.Install exterior panel (A)A
96.Install in Nterior panel ( )NQPP
107.Fix wi h th t e mortise(G)JB B
118.Mount handles AEEOMO
129.Install the batteryR
1310.Mark and drill holes for strike3.5 mm21 mm181 mm124 mm21 mmIKLI
14Step1: Remove the cover on the key hole with a sucker(T ).Step2: Insert mechanical key (S) into the key hole and rotate it at 90°.11. Test Lock by mechanical key (S)TS
15ZK Building, Wuhe Road, Gangtou, Bantian, Buji Town, Longgang District, Shenzhen China 518129Tel: +86 755-89602345Fax: +86 755-89602394www.zkteco.com© Copyright 2017. ZKTeco Inc. ZK Teco Logo is a registered trademark of ZK Teco or a related company. All other product and company names mentioned are used for identification purposes only and may be the trademarks of their respective owners. All specifications are subject to change without notice. All rights reser ved.FCC warning:Any Changes or modifications not expressly approved by the party responsible for compliance could voidthe user's authority to operate the equipment.Note: This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmfulinterference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-Consult the dealer or an experienced radio/TV technician for help.The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Navigation menu