ZMODO Technology SHRZ01W ZM-SHRZ01W User Manual 2

Download:
Mirror Download [FCC.gov]
Document ID	3090634
Application ID	jIWb8ePbYmBm99djRZXcsg==
Document Description	User Manual -rev
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.78kB (922307 bits)
Date Submitted	2016-08-07 00:00:00
Date Available	2016-08-10 00:00:00
Creation Date	2016-07-26 13:21:02
Producing Software	Corel PDF Engine Version 16.1.0.843
Document Lastmod	2016-07-26 13:21:02
Document Title	未命名 -2
Document Creator	CorelDRAW X6
Document Author:	tina

QUICK
START
GUIDE
Congratulations! We are excited to welcome you to the
next generation of smart technology. Beam can work
with your wireless router to extend the range of your
wireless network to areas of your home or office that
previously had little or no signal. It has three LED color
options that allow you to customize its nightlight to fit
your needs. This quick start guide will help you
configure your Beam for initial use.
Before you begin
Beam's hardware
Location requirements
During thunderstorms, please unplug Beam to
prevent it from getting damaged due to lightning
strikes.
Try to locate Beam about half way between your
wireless router and the furthest area you will want
to push wireless signal.
Locate Beam in a spacious place, such as near
hallways or corridors.
Choose a location away from electronic appliances
that generate strong magnetic or electric fields,
such as a microwave oven or a refrigerator.
PIR sensor
USA type B plug
Light sensor
Reset pinhole
LED nightlight
Environmental requirements
Keep Beam far from sources of heat and fire, such
as heaters or candles.
Place Beam in a cool and well-ventilated indoor
area. Do not expose Beam to direct sunlight.
Note: To reset Beam, insert a paper clip or similar thin object into
the reset pinhole, and press and hold for 10 seconds.
Quick setup
Do not place any object (such as a candle or a
water container) on the device. If any foreign
object or liquid enters the device, stop using the
device immediately, power it off and then contact
our support team.
Please make sure Beam is always within the
wireless coverage of your wireless router.
Do not block Beam with any object. Reserve a
minimum space of 10cm around Beam for heat
dissipation.
The operating distance range of your wireless
connection can vary significantly depending on the
physical position of your wireless devices. In order to
optimize the performance of your Beam, please follow
the instructions:
Zmodo Beam
Smart WiFi Range Extender
with LED Nightlight
Log in and select the Add
Device (+) option under the
menu in the upper left corner.
Power on your Beam, and tap √
√
to go to the next step.
In your WiFi settings page,
please select the network
named “AP_ZMD” and connect
to it.
Tap “Zink” to configure your
Beam.
Tap √ to proceed. (Only one
Beam can be added at a time.
If you have multiple Beams,
please repeat the setup
process for each.)
10
Return to the Zmodo app page,
enter the name and password
of the 2.4GHz WPA/WPA2
encrypted WiFi network your
Beam should connect to. Tap √
√
to proceed.
Select the “Normal” option.
Read the notes on the screen
and then tap the “Tap here to
select WiFi” option to go to the
WiFi settings page on your
smartphone.
11
If this app interface appears,
please press “Tap here to
select WiFi” to go to the next
step. (If your WiFi connection
on your phone automatically
changes back to your home
network, this pop up will not
appear, and you can skip to
step 13).
Follow the steps below to configure Beam with your
wireless router. For detailed instructions and
troubleshooting, please visit
www.zmodo.com/support
Plug Beam into a power outlet near your wireless
router to power it on.
Make sure you know the SSID (name) and
password of the 2.4GHz WPA/WPA2 WiFi network
that you will connect your Beam to before starting.
Download and install the 'Zmodo' app from
Google Play TM or the App Store TM . Launch the app
and sign up for a free Zmodo account.
Smartphone requirements: iOS (v7 or newer) or
Android (v4.0 or newer).
Zmodo
Note: Please make sure you are updated to the latest
version of the Zmodo app available.
12
15
Select your own WiFi network
and connect to it. Return to the
Zmodo app after connecting to
that network.
13
14
Zink will automatically search
for your Beam and connect it to
your WiFi network. This may
take a few minutes.
Name your Beam and set a
password for it. Tap √ to
proceed.
Note: The password provides an
additional layer of security for your
Beam. You will not need to use this
password to access your Beam from
the Zmodo app.
Beam has now been configured
successfully and added to your
wireless network.
Beam
In Manual mode, you can
choose any light color you like
among the three colors, and
can switch the nightlight on
and off through the device
settings page of the app.
Having difficulty?
10
10
11
Support
Connect with us!
Like us on Facebook.com/Zmodo
Scan the QR-code below
Android is a trademark of Google Inc. Google Play is a
trademark of Google Inc. Apple, the Apple Logo, and iPhone
are trademarks of Apple Inc., registered in the U.S. and other
countries. App Store is a service mark of Apple Inc.
13
LED nightlight control interface
Beam's LED nightlight has three light color options
and three light modes. The LED light colors and
modes can be adjusted in the app.
Control options
12
After your Beam is successfully connected, you
can relocate it farther from your router to extend
your network further. Please make sure it's still
within range of your router's WiFi network.
Beam can also be used to configure Zmodo
accessories that require a Zmodo hub to operate.
Follow us on Twitter @Zmodo
Scan the QR-code below
Zmodo Web App
In addition to the mobile app, you can also access and
control your Beam's settings from your computer. Just
log into the free web app at user.zmodo.com with your
Zmodo username and password.
Optimal placement
Enjoy: After configuration, Beam shares the same
WiFi Network Name (SSID) and WiFi password as
your wireless router or wireless access point.
Beam acts as more than just a WiFi range extender. It is
also a smart hub. After Beam is successfully
configured, you can use it to easily set up other Zmodo
smart cameras and devices, such as Pivots, Greets,
and more.
www.zmodo.com/support
Configure other Zmodo devices
with Beam
For more instructions, troubleshooting, support, and
other resources, please visit:
In Auto mode, the nightlight
will turn on automatically when
it's dark and someone passes
by. You can pick a color and
schedule the time that you
want your nightlight to last: 30
seconds, 60 seconds or 120
seconds.
Adding devices using Beam is very simple. Log in and
select the (+) Add Device option from the menu found in
the top left corner of the home screen. Tap the "Zink"
option, and then choose "Beam Connect". Make sure
your devices are powered on, and then select the
number of devices you are setting up at once by using
the [+] and [-] icons. Follow the on-screen instructions
to complete setup.
Plug the Beam into a power outlet about half-way
between your wireless router and your Wi-Fi dead
zone. The device will automatically reconnect to
your router within 30 seconds.
In Timer mode, you can not only
select the light color, but also
schedule the time of day that
your nightlight is on.
Important Information
1.This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
2.changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
14
11
– Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
3.This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 20cm between the radiator and your
body. This transmitter must not be co-located or
operating in conjunction with any other antenna or
transmitter.
15

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 1
Create Date                     : 2016:07:26 13:21:02+08:00
Modify Date                     : 2016:07:26 13:21:02+08:00
Producer                        : Corel PDF Engine Version 16.1.0.843
Author                          : tina
Creator                         : CorelDRAW X6
Title                           : 未命名 -2

EXIF Metadata provided by EXIF.tools