ZONDA HOBBY TECHNOLOGIES ELECTRONIC HK0003 2.4GHz Transmitter User Manual GWY005451 GWY 6TL V2 Transmitter

Download:
Mirror Download [FCC.gov]
Document ID	2140872
Application ID	o8zB80qVjCpqXyaaRa7VdQ==
Document Description	User Manual.PDF
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	150.06kB (1875728 bits)
Date Submitted	2013-12-12 00:00:00
Date Available	2013-12-12 00:00:00
Creation Date	2017-10-24 15:39:00
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-24 15:39:00
Document Title	GWY005451 GWY 6TL-V2 Transmitter.cdr
Document Creator	CorelDRAW Version 9.397
Document Author:	sstc

GWY005451
6TL Transmitter
1.Transmitter components introduction
Antenna
Trainer/Bind
Mix / Hold
3D switch (Mode 2/ Mode 4)
Tail Blade pitch (Mode 1/ Mode 3)
3D switch (Mode 1/ Mode 3);
Tail Blade pitch (Mode2 /Mode 4)
Gear
Aileron D/R
Elevator D/R
Aux 1
Mode1
Mode2
Mode3
Mode4
Flap Gyro
Mode1
Mode2
Mode3
Mode4
elevator and rudder stick
throttle and rudder stick
elevator and aileron stick
throttle and aileron stick
throttle and aileron stick
elevator and aileron stick
throttle and rudder stick
elevator and rudder stick
Mode 1 /Mode 3 throttle trim
Mode 2 / Mode 4 elevator trim
Mode 1 / Mode 2 aileron trim
Mode 3 / Mode 4 rudder trim
Mode 1 /Mode 3 elevator trim
Mode 2 / Mode 4 throttle trim
Power button
Mode 1 / Mode 2 rudder trim
Mode 3 / Mode 4 aileron trim
LCD setting module
2.Transmitter standard and parameters
1)The frequency bandwidth: ISM 2.4GHz (2.400~2.480GHz)
2)number of controller is 6CH
3)The operation current is not greater than 150 mA (include LCD screen);The charging current is not
greater than 500mA.
4)The battery is Li-Polymer battery (3.7V), the volume is 780 mAh
3.Product Features
1) The transmitter is using 2.4G ISM frequency channel, allow auto detection while using the transmitter.
2) The transmitter receive or distribute the frequency by ID identify technology, protect external jamming,
provide stable and reliable during the operation.
3) The LCD setting module is dividable, user-friendly and setting the trim easily.
4) Interchanging interface easily (Change Mode + Menu setting)
5) Trainer connector is using wireless technology
6) The power button is using soft material to become the button, it is durable and change the connection
defect while pushing the roller power button
7) The transmitter is based on the ergonomic technology to design the transmitter
4.Interchanging position of throttle and elevator control
Structural adjustment: Before the adjustment, please take out the four rubber pistons (A, B, C and D) on the back
of the transmitter, as shown in the figure
Left Throttle to Right Trottle (Mode 2/Mode 4 to Mode 1/ Mode 3)
1 Use a cross-drive screw driver to loosen Screw A. Keep loosening until the stick can move up and down
without friction
2 Tighten Screw B. Keep tightening until the stick can move up and down with rebounds
3 Loosen Screw C. Keep loosening until the stick can move up and down without rebounds
4 Tighten Screw D. Keep tightening until the stick can move up and down with friction
Right Throttle to Left Throttle (Mode 1/Mode 3 to Mode 2/ Mode 4)
1 Use a cross-drive screw driver to loosen Screw D. Keep loosening until the stick can move up and down
without friction.
2 1)Tighten Screw C. Keep tightening until the stick can move up and down with rebounds.
3 Loosen Screw B. Keep loosening until the stick can move up and down without rebounds
4 Tighten Screw A. Keep tightening until the stick can move up and down with friction
Back view of Transmitter
Elevator Stick
Rudder Stick
Throttle Stick
Aileron Stick
Aileron Stick
Rudder Stick
MODE 4
Throttle Stick
Elevator Stick
MODE 3
Rudder Stick
Elevator Stick
Aileron Stick
Throttle Stick
Rudder Stick
MODE 2
Throttle Stick
Elevator Stick
MODE 1
Aileron Stick
Set Control Mode, change of control mode
There are 4 Control Modes: Mode 1, Mode 2, Mode 3 and Mode 4, as shown in the above
Changing control mode
1 Push and hold both the R/A Trim (Rubber/Aileron Trim) leftward at the same time then press the Bind button.
The transmitter will emit a series of beep sound. That indicates the transmitter has entered the control mode
setting.
2
Select your desired control mode by pushing the T/E Trim (Throttle/Elevator Trim) as instructions and picture
shown below:
Push the right T/E Trim upward for MODE 1, one beep sound will be emitted.
Push the right T/E Trim downward for MODE 2, two beeps will be emitted.
Push the left T/E Trim upward for MODE 3, three beeps will be emitted.
Push the left T/E Trim downward for MODE 4, four beeps will be emitted.
3 After the desired control mode is selected, push the left R/A Trim (Rubber/Aileron Trim) to the right as shown
below in figure 3, corresponded beeping sound as when setting the control mode will be emitted (1 beep for
MODE 1, 2 beeps for MODE 2 etc.), the transmitter will then save the selected control mode and turns off
automatically. The selected control mode will be in use the next time when the transmitter is turned on.
BIND
T/E Trim
MODE 3
MODE 1
MODE 4
MODE 2
Power button
R/A(RUDD/AILE)
R/A(RUDD/AILE)
Figure 1
Figure 2
Figure 3
5.Normal instruction
1) Turn on transmitter procedure: Press and hold the power button 3~5 second, the buzzer will have a beep noise, the
LCD icon will light on and solid. This signal means the transmitter is turn on successfully.
2) Binding procedure: Insert the binding plug in the Channel 9 (Power supply interface) receiver / 3 axis gyro and connect
the electricity, the LED will fast flashing. Pressing and holding the transmitter binding button and power on the transmitter.
When the transmitter was power on, you should release the power button first and wait for 10 seconds after, release the
binding button lastly. If the above procedure is success, the LED will solid after 5 seconds and the binding process is
completed, remove the binding plug. Otherwise, please follow the above procedure to bind it again. (Note: To operate the
binding procedures, please make sure the brushless motor and the ESC is not connected.)
Press the Binding button and the power
button at the same time
LED fast flashing
Jack in the binding plug
LED fast flashing
Remove the binding plug
LED steady light
Pressing and holding the transmitter binding
button and power on the transmitter. When the
transmitter was power on, you should release
the power button first and wait for 10seconds
after, release the binding button lastly
LED steady light, Remove the
binding plug
3) Turn off transmitter procedure: Press and hold the power button 3~5 second, the buzzer will have a beep noise, the
LCD icon will light off and solid. This signal means the transmitter is turn off successfully.
4) Trainer wireless binding: Open the transmitter (Master transmitter), plug in the wireless connection device through the
30 Pin connector, after that press and hold the binding button, it will auto detect the wireless connection device and
connect with the transmitter in 20 seconds. If success, the LED wireless connection device will solid.
5) Charging procedure: Plug in the charging connection wire to the transmitter via the 30 Pin charging connector, and then
plug the USB connector in the 5V charger.
6.Normal and aerobatics mode
GWY 6T channel helicopter is installed an aerobatics curve in the transmitter, switch off the transmitter, the pitch and
throttle is automatically exchange into suitable for aerobatics mode used. The picture below: (Left throttle).
F MODE / OFF
F MODE / ON
Normal
When the transmitter is closed the aerobatics mode, the throttle curve is linear from 0% to 100%. The helicopter
under this mode, it will change the setting depends on throttle curve from 0% to 100% and the pitch curve from -3
degrees to +10.5 degrees (factory default setting). This is the preferred flight mode for general hovering and basic
flight. (The user can use the GWY setting module or connection wire to connect with the computer to reset the
pitch and throttle curve)
Pitch Curve
Throttle Curve
+10.5
100%
+10.5
50%
-3
Bottom
Throttle Control Stick
0%
High Bottom
Throttle Control Stick
-10.5
High
Aerobatics
When the transmitter is opened the aerobatics mode, the helicopter is under the 3D aerobatics mode. In this
mode, the throttle curve is remain at 100% and becomes a V shape status. If the throttle curve change from
0% to 100%, the pitch curve change from -10.5 degrees to +10.5 degrees (factory default setting). This is the
preferred flight mode for aerobatics flight. (The user can use the GWY setting module or connection wire to
connect with the computer to reset the pitch and throttle curve)
Pitch Curve
Throttle Curve
100%
+10.5
+10.5
50%
-10.5
Bottom
Throttle Control Stick
0%
High Bottom
Throttle Control Stick
-10.5
High
7.The transmitter control instruction
Mode 1
Mode 2
Mode 3
Mode 4
When the throttle stick is pushing up, the helicopter will increase the speed and flight up. When the throttle stick is
pushing down, the helicopter will decrease the speed and flight down.
When the rudder is pushing left, the helicopter will turn left; when the rudder is pushing right, the helicopter will turn right.
Mode 1
Mode 3
Mode 2
Mode 4
When the elevator is pushing up, the helicopter will flight front; when the elevator is pushing down, the helicopter will flight back.
When the aileron is pushing left, the helicopter will flight left; when the aileron is pushing right, the helicopter will flight right.
8.Trouble Shooting
Trouble Description
Possible reason
Solution
Can not turn on the
Changing battery and re-charging the battery
Missing battery or voltage
transmitter
Turn on the transmitter,
1)Please check the throttle stick position, push down the stick at
1)Throttle position has not push down to the lowest position.
Buzzer
the lowest position.
have noise but can not 2)Other functions can not go back to default "0" position.
2)Please check all the functions button or switch, and adjust the
turn on the transmitter.
value back to "0" position
1)Please press the binding button to re-binding the transmitter
1)When turn on the transmitter, user press the binding 2)Please stay in a flat area without heavy or many metals
Can not connect with
button carelessly
surounded area
the receiver normally 2)Is there any metal or other material suround with you
3)Please check the receiver battery power and connector is
3)The helicopter is not charging normally
connected correctly
Remote control area
1)Is the receiver antenna mix with the other device wire The receiver antenna must have a distance with other
has not achieve the
together?
electronic wire (at least 20mm)
standard
2)Is the receiver antenna loose or damage?
1)Is it the helicopter type not correct?
Remote control can not 2)Is it Servo not working properly?
3)Is there any strong frequency jammed, affecting the
operate properly
transmission quality?
1)Please make sure the transmitter setting is matching
with the correct helicopter model
2)Please make sure the servo is working properly
3)Please make sure there is no any big frequency device
in the area. It is include wireless router or frequency tower
Under the operation, LED
is flashing unexpectedily, The battery power is very low (Lower than 20%)
or connection error, occur the alarm.
the Buzzer have noise
contiuously.
Please check the battery stick tight, and then check the
battery power. Charging the battery on time and replace
the battery if necessary.
FCC ID: 2AAB6-HK0003
Item Number:GWY005451
Zonda Hobby Technologies Electronic Ltd
Warning: Changes or modifications to this unit not expressly approved by theparty responsible for compliance
could void the user s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radiofrequency energy and,
if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
To comply with FCC s RF radiation exposure limits for general population/uncontrolled exposure, this device
must be operated only in hands with a separation distance of at least 20 cm from its antenna to the body. In addition it must not be collocated or operating in conjunction with any other antenna or transmitter.
Correct Disposal of this product. This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To
return your used device, please use the return and collection systems or contact the retailer where the product
was purchased. They can take this product for environmental safe recycling.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
Hereby, ZONDA HOBBY TECHNOLOGIES ELECTRONIC LIMITED, declares that this
GWY005451 is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Extract, Print high-res
Author                          : sstc
Create Date                     : 2013:09:09 10:10:43Z
Modify Date                     : 2013:12:11 23:22:16-08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Creator                         : sstc
Title                           : GWY005451 GWY 6TL-V2 Transmitter.cdr
Creator Tool                    : CorelDRAW Version 9.397
Metadata Date                   : 2013:12:11 23:22:16-08:00
Producer                        : Corel PDF Engine Version 9.397
Document ID                     : uuid:b689685a-149b-4ebb-9095-eff5c1a476f2
Instance ID                     : uuid:8fafb12f-2aad-41bc-b663-b8dff9d5a1d6
Page Count                      : 6

EXIF Metadata provided by EXIF.tools