ZONDA HOBBY TECHNOLOGIES ELECTRONIC HK0008 ESKY E150X User Manual Users manual

Download:
Mirror Download [FCC.gov]
Document ID	3192770
Application ID	tUHxO8360ETd3yPrXG+6Ow==
Document Description	Users manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	145.49kB (1818622 bits)
Date Submitted	2016-11-10 00:00:00
Date Available	2016-11-10 00:00:00
Creation Date	2016-10-20 14:41:42
Producing Software	Adobe Acrobat 10.1 Image Conversion Plug-in
Document Lastmod	2016-10-20 14:41:42
Document Title	Users manual
Document Creator	Adobe Acrobat 10.1

ESKY150X Es_kv”
Safety Precautions and Warnings
RC helicopter is controlled by radio signals. it may be interiered by other radio signals during operation. These
interference may cause the helicopter lose control.
1.lmproper operation to Esky1§0X may lead to damage or loss. it is prohibited for children under
i4 years lo operate this product
2.Keep Itawaytrom high temperature environmentfor storage and liight.
lsuggested operation temperature: 5-351: Humidity: 20-50%
4.Keep away lrom tan, air conditioner, table lightwhile llying.
5 Do not contact the molor in case ordamageor injury
i.Keep away lrom crowds in case ofaccidents.
2 Do not operate Esky150x in shower room or under rain Moisture may go inside the helicopter
® Pruhibilion which may cause electronic parts mailunction and unexpected incident
3.Da not re—aouip, upgrade or repairyour helicopterwilh unauthorized parts.
4.Keep people and objects away lrom the spinning unitand parts in case otdamage oriniury.
Helicopter Parts
Man an. $36233: “
Main aiade‘i
fl
Flight Operation Procedure
1,Preflight Proceduce
1)Set the Throttle Stick [Right Stick(Mode1)/Lefl stiaklwtodezu down to bottom and power on the tensrnitter,
2) Put the helicopter on the ground or iiat, power on the helicopter, make sure the helicopter remins lial until the
helicopter pass the seif—tesling.(Condilion Blue LED light irorn quick hashing to slow hashing in the indicator)
3) Safety Unluck:
Mode1 Modez
Keep the ”gill stick down to bottom, than pushing Keep the Len Sllck down to bottom, then pushing the
the L.“ suck to Right for at least 3 seconds and Left SUCK to Right Bottom Comet for at least 3
release.(COnditiori blue LED lighl from slow flashing to Seconds and release.(COnditan blue LED light lrom
ouick rlashing in the indicator) slow flashing to quick liashing in the indicalor)
4) Take Off: Please take off in 10 seconds’ If not’ Helicopter will automatically lock.
. Unlockthe helicopter by step 3i M “and “Mme ”gm “and “mm”
2. End Flight Proceduce
1) Power off the Helicopter
2) Power off the Transmitter
Transmitter
1, Transmitter LED '"mca‘m
Leit Hand Throtte "wagnagsmns ”w
Mode 2 r
( ’ Throttle at Rudder suck Elavatnr Mtiemh Stidt
(ModaZ) 7/» (Mode2)
fir \ , ‘ ‘,
Throttle Trim Lever ‘ ' x , I I i ElavatarTnm Lever
(Mode 2) ‘ ‘ ‘ (Mode 2)
/,
RudderTrim Lever‘ " " ' ‘Aiieran Tim! Lever
(Mode 2) r ‘(Mud22)
Fewer Switch
PS Hover Mode (Press Hover/Maneuvering Mode Switch “Beep" that Hover Mode).
Maneuvering Mode (Press Hover/Manauvsring Mode Switch, “Beep"‘Beep” that Maneuvaring Mode).
Hover Mode defaulted when turn an the transmitter, it was recommended to landing when switch mode.
2. Transmitter Conlrol - Mode 2
When pushing the THROTTLE s. RU DDER stick up or dawn, the heiimpler iifls up or ascends aocordingiy.
When moving the THROTTLE a. RUDDER stick Ieit or right. the head oi the helicopter moves left or right aocordingiy.
When pushing the ELEVATOR &AILERON stick up or com. the helicopler moves forward or backward accordingly.
When pushing the ELEVATOR atAILERON stick heel or right, the head of the helicopter siiaes Ian or right accordingly,
Transmitter
3_ Tmnsmmer LED Indicator
my,“ Hm ”We Hnfiweagarfirmg ‘; Amenna
(“we U Elavamr a. Rudder Suck ' Throws &Allemn suck
(Mode 1) (Mode 1)
ElevalarTnm Lever r ‘ , Thmme Trim Lever
(Mode 1) _ - , (Mode 1
¥ <- J .
Runner Tnm Lever ‘ \ ‘ Maren Tnm Lever
(Mode 1. r r (Mode 1)
r V r
Power Switch
EST Hover Mode (Press Hover/Maneuvering Mode Swilch, “Beep” thal Hover Mode)
Maneuvering Mode (Press Hover/Maneuvering Mode Switch, “Beep"“Eeep' thin Maneuvering Mode)
HnVer Made defaulted when turn on (he iransmitter. it was recommanded In landmg when switch mode.
4. Transmmer Control - Mode 1
When pushing me THROTTLE & AILERON suck up or down, [he helimpler lifls up or ascends accordinmy.
When muvrng the ELEVATOR & RUDDER slrck Ian or ngm, me head of the hellcupler muves lefl er rrgm accordingly
When pushing me ELEVATOR & RUDDER stick up or down, the hel‘oopler moves forward or backward awording‘y.
When pushing the THROTTLE & AILERON sfick {en ar right the head or the helicuplar slides lsfl or nghl acmrdingly
B I n d I n 9
ti Switch all "summer. avvitch on helicopter. the condition green LED lrorn
helicopter llashes repidly.
2) Press |he llgm hullan al the rudder lnm level lmm [he lmnsmmel and switch
unme transmllter.
3) When the condition LED lrorn helicopter is extinguished, release the ngnt
button until the helicopters condition green LED reilghts which implies the
blnding is completed (Helipopterwaa completely hinded in the tactory setting.)
Command Problems FAQ
Situatlo it
Why the battery bulge belore second
filghl?
Why Ihe helicopter not stable when
flight?
Why the helicopter green light being
slaw flash?
Why the green light so not solid on the
hellccphsr”
How do I know when a ballery is 100%
charged?
What is the funcllon 07 the Dual Rate
Eumn?
Blades overlapping
Heavily skewed when tlight
Heavily unstable when flighl
Reason
Over discharge the battery
Due to some parts fixed error
LlPo battery low voltage protection
Do not receive any signal
When the charger light charge
lrom red to green
Right button at the rudder trim lever
Solution
Replace a new battery
Adjust by trim lever
LiPo battery low voltage protection
Do not receive any signal
When the charger light charge
lrom red to green
To swnch the tlight mode and sensitive between 1x and Helicopter
Blade detormed
Linking parts separated
Sensor swot analysis mistakes
Rater to main blade adjustment
Check each linking parts
Reboot the helicopter
P s the development oi the eskv 1qu would not have been possible without the etioit or a large team ot lrldlvlduals who invested in the open source
itightmnlroller sonwaie that nihninp on the Eskv ISDX.
Main Blade Adjustment
it the helicopter blades overlapping, adjust it as below:
A. Yellow at the Top:
Adjust ball link ol main blade lionl edge (Diagram A in F t) clockwise rotate one time and adjust
belt link ol main blade back edge counterclockwise rotate one time. until the problem solved-
B. Yellow at the Bottom: Adjust ball link otmain blade iront edge (DIagramA in P.1)courlterclockwlse rotate onetime
and adjust ball linit ol main blade back edge clockwtae rotate onetime until the problem solved
Spare Parts
, J _
‘G‘ ‘ H“ " QUE”; " W
-' Ta? is a (a rd o 'i ‘ bi
lb we) m @g bi g!)
I I Y i u ii i
ESKVOOSSlO ESKY006404 ESKV006311 ESKY006406 ESKY006407
Mail RtmrBladeGlpSel Swashplale Sal Main Gear Ball Llnk Servo Set
H i
2: 8 8 S33 8 El Wm 3
ESKYOOBAOB ESKY005439 ESKYOOSEDS ESKY005435 ESKY006007
Rotor Housing Sal Bearing: 3'6'2 Bearing 5'8‘2 LiPn Battery USB Charger
" R! V a ct
., ,. 7 t . d—J
V I‘ — .
.. *1 5' :5":
ESKY005437 ESKvoos437a ESKY006316 Esxvoouos esxvonsms
TrensmtttertMouez) Transmtlter(Mode1) Screws Set Psuhrod Set 1sz Tait Blade
7‘ 1/", H
e , ,
LA M
" / v n
ESKYoosan ESKYoosats ESKY006319 ESKY006320 ESKYODSSH
Canopy Main Frame Tall Mater (/w mount) Landing Skid Set Metn Flight Contrut
“ H t n
"WM @3594“
\a \s \= ‘17
ESKY006402 ESKV006313 ESKV007024
Main Btade Mam Motor Double-sided suckers
Charging the UFO Battery by USB Charger
1) Plug the 3 7V LIFO Battery IMO the USE charger LIPu Batteq Port
2) Plug the use charger into the usa part olnompmst or chargst.
Then there Is a sand red light on the usta chargers LED Indicator. fl,mm[f age E “ U53 F‘ug
3)When the UFO Battery is tuttycharged, the red light will change tu V
green trght.
Sgnal LED x
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursue
ant to part 15 of the FCC Rules, These limits are designed to provide reasonable protection against
harmful interference in a residential installation This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instmctions, may cause harmful
interference to radio communications
However, there is no guarantee that interference Wlll not occur in a particular installation If this equipm-
ent does cause harmful interference to radio or television reception. which can be determined by turning
the equipment off and on. the user is encouraged to try to correct the interference by one or more of the
followrng measures:
- Reorient or relocate the receiving antenna
- increase the separation between the equipment and receiver.
' Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the tollowmg two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Note: Modifications to this product will void the user's authority to operate this equipment.
Global Dislributinn Office
Zonda Hobby Technologles Eleclmmc Limited
Room4D4. 4IF, Black A, Hoplite Industrial Centre. No. 35 Wang Tai Road, Kowloon Bay. Kowloon. Hong Kong
Tel: (852)31508886 Fax: (852)31608884
Official Website: www.20ndanobhy.cam I www.20ndahobby.com.cn

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Create Date                     : 2016:10:20 14:41:42+08:00
Creator                         : Adobe Acrobat 10.1
Modify Date                     : 2016:10:20 14:41:42+08:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2016:10:20 14:41:42+08:00
Creator Tool                    : Adobe Acrobat 10.1
Format                          : application/pdf
Document ID                     : uuid:b75b87ff-b400-4e42-b18c-b6adafc8df9e
Instance ID                     : uuid:86685cc5-859b-4cc8-9ef9-6e4a77319151
Producer                        : Adobe Acrobat 10.1 Image Conversion Plug-in
Page Count                      : 6

EXIF Metadata provided by EXIF.tools