ZTE TRUNKING TECHNOLOGY PH5Y0U2 Two way radio User Manual
ZTE TRUNKING TECHNOLOGY CORPORATION Two way radio Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2699374 |
| Application ID | G6SvawK5MnsJDYZksF4/Og== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 43.17kB (539609 bits) |
| Date Submitted | 2015-07-31 00:00:00 |
| Date Available | 2015-07-31 00:00:00 |
| Creation Date | 2015-06-03 10:21:45 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2015-07-27 17:28:37 |
| Document Title | Users Manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
Legal Information Getting Started Copyright © 2015 ZTE Trunking Technology Corporation Please read the following carefully: All rights reserved. How to use this manual… No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Trunking Technology Corporation. What can you get from your agent or system administrator… The manual is published by ZTE Trunking Technology Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. The information on the package is only for your reference. Images are for your reference only. Please check the product model before purchasing. Install the Antenna How to use this manual? The LED indicator indicates operation of the HT. Noise reduction: switches between large noise reduction and normal noise reduction. • If the indicator is lit red, it indicates that the HT is transmitting signals. • If the indicator is lit green, it indicates that the HT is being turned on, or receiving a call or data. To remove the interface cover, press the cover, and loosen the screw anticlockwise. Lift up the cover, and slide it down. Turn the volume/power knob clockwise until you hear a click sound. The HT gives a short beep sound, indicating that the HT is successfully turned on. Adjust the Volume One-press call: initiates a predefined private call, group call, or short message by pressing one button. 3. Press the PTT button to respond to the call. The LED indicator is lit red. 4. Wait until the call admission tone (if activated) ends, and speak to the microphone. 5. Release the PTT button to listen to other members in the call. 6. If no one talks within a specified period, the call ends. Receive and Respond to a Private Call A private call means a call that a single HT initiates to another HT. There are two types of private calls. In the first type, the calling HT performs an HT existence check before preparing for a call. In the second type, the HT directly prepares for a call. When your HT is selected, the LED indicator is lit green. Only one type of private calls can be programmed on your HT. When you receive a private call, perform the following steps: 1. Verify that the LED indicator is lit green. 2. Hold the HT vertically, and keep it about 1 to 2 inches (2.5 to 5.0 cm) away from your mouth. If the "idle channel prompt" function is enabled, when the transmitting HT releases the PTT button, you will hear a short prompt sound, indicating that the channel becomes idle, and you can respond. 3. Press the PTT button to respond to the call. The LED indicator is lit red. 4. Wait until the call admission tone (if activated) ends, and speak to the microphone. 5. Release the PTT button to listen to the other member in the call. 6. If no one talks within a specified period, the call ends. • Pre-programmed button for a one-press call Initiate a Call With the Channel Selection Knob Initiate a Group Call To initiate a group call, you must join a call group on the HT. Perform the following steps: 1. Turn the channel selection knob, and use an activated call group ID for selecting a channel. 2. Hold the HT vertically, and keep it about 1 to 2 inches (2.5 to 5.0 cm) away from your mouth. 3. Press the PTT button to initiate a call. The LED indicator is lit red. 4. Wait until the call admission tone (if activated) ends, and speak to the microphone. 5. Release the PTT button to listen. When a target HT in the call responds, the LED indicator is lit green. 6. If the "idle channel prompt" function is enabled, when a target HT releases the PTT button, you will hear a short prompt sound, indicating that the channel becomes idle, and you can respond. Press the PTT button to respond. If no one talks within a specified period, the call ends. Initiate a Private Call Perform the following steps: 1. Turn the channel selection knob, and use an activated user ID for selecting a channel. 2. Hold the HT vertically, and keep it about 1 to 2 inches (2.5 to 5.0 cm) away from your mouth. This function enables you to transmit signals to all the users on the same channel. You must enable this function on your HT before using this function. Perform the following steps: 1. Turn the channel selection knob, and use an activated general call group ID for selecting a channel. 2. Hold the HT vertically, and keep it about 1 to 2 inches (2.5 to 5.0 cm) away from your mouth. 3. Press the PTT button to initiate a call. The LED indicator is lit red. 4. Wait until the call admission tone (if activated) ends, and speak to the microphone. Other users receiving the general call cannot respond to the call. Initiate a One-Press Group Call or Private Call The one-press call function enables you to call a predefined group ID or user ID by pressing one button. This function can be assigned to a press operation or a press-and-hold operation on a programmable button. You can assign only one ID to one programmable button. There are multiple programmable buttons for the one-press call function. Perform the following steps: 3. You can use the following advanced functions: 4. Release the PTT button to listen. 5. If you do not respond within the idle time, the HT continues to scan other channels or call groups. Scanning… When you start scanning, the HT scans the pre-programmed scan list on a cycle basis to check whether someone is speaking on the current channel. The LED indicator is flashing red. Scanning modes • Main channel scanning (manually): The HT scans all the channels or call groups in your scan lists. Depending on the configuration, your HT may start scanning from the last scanned active channel/user group or the channel for which scanning is enabled. • Automatic scanning (automatically): When you select a channel or call group for which automatic scanning is enabled, the HT automatically starts scanning. Press a pre-programmed button to call a predefined group ID or user ID. Start and Stop Scanning 2. Hold the HT vertically, and keep it about 1 to 2 inches (2.5 to 5.0 cm) away from your mouth. Perform the following steps: 3. Press the PTT button to initiate a call. The LED indicator is lit red. 4. Wait until the call admission tone (if activated) ends, and speak to the microphone. 5. Release the PTT button to listen. When a target HT in the call responds, the LED indicator is lit green. 6. If the "idle channel prompt" function is enabled, when the target HT releases the PTT button, you will hear a short prompt sound, indicating that the channel becomes idle, and you can respond. Press the PTT button to respond. If no one talks within a specified period, the call ends. When a private call ends, you will hear a short prompt tone. You can use a pre-programmed button to send a short message predefined by your agent. Perform the following steps: Scanning 1. Wait until the call admission tone (if activated) ends, and speak to the microphone. Send a Predefined Short Message You can create a scan list and assign it to a single channel or call group. The HT scans the channel or call group queue in the list on a cycle basis to check whether someone is speaking on the current channel. The HT supports a maximum of 250 scan lists, and each list supports a maximum of 31 members. 1. Press the pre-programmed scan button. Or turn the channel selection knob to select a channel for which automatic scanning is enabled. 2. When scanning is started, the LED indicator is flashing red, and you will hear a positive prompt tone. When scanning is stopped, the LED indicator is not lit, and you will hear a negative prompt tone. When the HT detects an active channel The HT stops at the detected active channel or call group. The HT stays on this channel for a pre-programmed duration call "idle time". Perform the following steps: 1. Hold the HT vertically, and keep it about 1 to 2 inches (2.5 to 5.0 cm) away from your mouth. If the "idle channel prompt" function is enabled, when the transmitting HT releases the PTT button, you will hear a short prompt sound, indicating that the channel becomes idle, and you can respond. 2. Press the PTT button within the idle time. The LED indicator is lit red. 10 High-pitch prompt tone Low-pitch prompt tone • Positive prompt tone • Negative prompt tone To switch between digital channels, turn the knob. You can use your HT after learning how to configure the HT. Receive and Initiate a Call Get familiar with the basic call function as follows: Select a zone… Receive and respond to a call… Select a Zone A zone defines a channel group. The HT supports a maximum of 250 zones, and each zone supports a maximum of 16 channels. Perform the following steps: Advanced Functions Scan List • • Initiate a call… • Initiate a General Call Repeated tone: The HT gives repeated tones until you end it. Momentary tone: The HT gives a tone for a duration specified by the HT. Press and hold: means pressing a button and holding the button for a pre-programmed duration (between 1 second and 3.75 seconds). PTT button Settings… • • • • SMS… Continuous tone: The HT gives a series of single tones continuously. Periodic tone: The HT gives a tone periodically based on the specified cycle. The tone is automatically started, stopped, and repeated. If the existing call is interrupted (for example, when you receive an emergency call), you will hear an idle channel prompt tone. You can disable the "idle channel prompt" function by disabling the tone/prompt function (for details, refer to the Enable or Disable the Tone/Prompt Function section). Assignable HT Functions Scan list… • • Select a channel, a user ID, or a call group ID… Monitoring: monitors any activities in a selected analog channel. If the "idle channel prompt" function is enabled, when the target HT releases the PTT button, you will hear a short prompt sound, indicating that the channel becomes idle, and you can respond. Press the PTT button to respond. If no one talks within a specified period, the call ends. During a call, if the "idle channel prompt" function is enabled (preprogrammed by your agent), when the target HT (that receives your call) releases the PTT button, you will hear a short prompt tone, indicating that the channel becomes idle, and you can respond. Prompt tones can help you learn about the HT status or response to data receiving. Press: means pressing a button and immediately releasing the button. • 6. If there is no existing call, you can press the PTT button to initiate a call (for details, refer to the Initiate a Call section). If the call admission tone function is activated, wait until the short prompt tone ends. Prompt Tone • HT control options Release the PTT button to listen. When the target HT responds, the LED indicator is lit green. Channel selection knob • During a call, if you press the PTT button, the HT transmits signals to other HTs in the call. Press and hold the PTT button to talk. Release the PTT button to listen to other members in the call. When you press the PTT button, the microphone is activated. Your agent can set a programmable button to a shortcut button for a function or channel or call group in accordance with the duration for which the button is pressed: Programmable buttons 5. • Programmable Buttons • When you receive a general call, perform the following step: • The button marked with an asterisk means a programmable button. • • Note: Align the battery with the battery slot on the rear side of the HT. Push the battery into the slot until it is fastened. Before removing the battery, turn off the HT first. Press the battery fastener, and then remove the battery. After selecting a zone (if there are multiple zones), you can turn the channel selection knob to select a channel, a user ID, or a call group ID. Initiate a Call HT Control Battery Emergency call: initiates or cancels an emergency alarm or call. Wait until the call admission tone (if activated) ends, and speak to the microphone. You can use either of the following buttons to select a channel, a user ID, or a call group ID: Turn the volume knob clockwise to turn up the volume. To turn down the volume, turn the knob anticlockwise. Belt clip • Press the PTT button to initiate a call. The LED indicator is lit red. Hold the HT vertically, and keep it about 1 to 2 inches (2.5 to 5.0 cm) away from your mouth. If the "idle channel prompt" function is enabled, when the transmitting HT releases the PTT button, you will hear a short prompt sound, indicating that the channel becomes idle, and you can respond. Microphone LCD • Universal interface Please read the following carefully: 4. 2. Speaker Install the Battery 3. Verify that the LED indicator is lit green. Side button 2* Side button 3* • Channel selection knob Power/volume button Keypad If you disable the tone/prompt function, no beep sound can be heard (for details, refer to the Enable or Disable the Tone/Prompt Function section). If your HT cannot be turned on, check the battery. Verify that the battery is charged and properly installed. If your HT still cannot be turned on, contact your agent. To turn off the HT, turn the knob anticlockwise until you hear a click sound. A general call means a call that a single HT initiates to all the HTs on the same channel. A general call is used to issue an important announcement. 1. Side button 1* Note: Receive a General Call When you receive a general call, if you switch to another channel, the HT stops receiving the general call. During a general call, you cannot use any programmable button until the call ends. Antenna PTT button Turn On the HT Select a Channel, a User ID, or a Call Group ID LED Indicator • Which optional accessories do you need? Prompt tone... Align the screw holes on the belt clip with those on the rear side of the HT, and fasten the belt clip with screws. • The HT is powered by a Li-Ion battery. To protect the battery from damage and comply with the warranty conditions, you can use only the charger provided with the battery for charging. To maximize battery performance, it is recommended to charge the battery for 14 to 16 hours before the first use. LED indicator... Power level: switches between transmitting power levels. Each channel can be configured as a digital channel. Charge the Battery To receive a call from a user group, you must configure the call group on the HT. Assignable Setting Functions PTT Button Adjust the volume. Note: Zone: changes the current zone of the HT. Install the Universal Interface Cover Turn on the HT. Receive and Respond to a Group Call • The universal interface is on the antenna side of the HT. It connects an accessory to your HT. Insert the universal interface cover fastener into the universal interface slot. Press the cover, so that it is fastened to the RF interface. Tighten the screw clockwise to fix the interface cover to the HT. Install the universal interface cover. When the HT is transmitting signals, the LED indicator is lit red. When the HT is receiving signals, the LED indicator is lit green. You can learn about HT operation through the following: Which buttons can be used to access other functions? Install the belt clip. If no one talks within a specified period, the call ends. If the "idle channel prompt" function is enabled, when the transmitting HT releases the PTT button, you will hear a short prompt sound, indicating that the channel becomes idle. You cannot respond to a general call. VOX: enables or disables the VOX function. Does your Handheld Transceiver (HT) have default channels? Install the antenna. 2. Scanning: enables or disables scanning. • • Install the battery. Verify that the HT gives a prompt tone, and the LED indicator is lit green. • Tone/prompt: enables or disables the tone/prompt function. Charge the battery. 1. Status Indicators • Perform the following steps to assemble your HT: Receive and Respond to a Call Encryption: enables or disables the encryption function for digital channels. • What can you get from your agent or system administrator? Ready to Use the HT After selecting a channel, a user ID, or a call group ID, you can receive or respond to a call. LED indicator • • Install the Belt Clip This manual describes basic operations on an HT. Your agent or system administrator may have customized your HT to address your special needs. For details, contact your agent or system administrator. PH520 U(2) Emergency button* To replace the antenna, use a specified antenna to replace the old one. Otherwise, your HT may be damaged. Please refer to each chapter for the details. You may ask your agent or system administrator about the following issues: HT Control Options Turn off the HT, place the antenna into the installation hole, and turn the antenna clockwise. To remove the antenna, turn the antenna anticlockwise. Before removing the antenna, ensure that you have turned off the HT and removed the universal interface cover. 1. Press a pre-programmed button to send a predefined short message to a predefined ID. 2. The LED indicator is lit red. 3. If the HT gives two chirps, it indicates that the short message is successfully sent. If the HT gives a low-pitch prompt tone, it indicates that the short message fails to be sent. Enable or Disable the VOX Function This function enables you to initiate a hands-free call. The HT automatically transmits signals within the specified period, regardless of when the microphone with the VOX function detects voice. During a call, if you press the PTT button, the VOX function is disabled. To reenable the VOX function, use one of the following ways: Note: Press the pre-programmed noise reduction button. 2. If you hear a positive prompt tone, it indicates that large noise reduction is applied. If you hear a negative prompt tone, it indicates that normal noise reduction is applied. Set the Power Level You can set the power level for each channel. If a high power level is set, the HT can communicate with HTs at a far distance. If a low power level is set, the HT can communicate only with HTs at a close distance. Accessories Your HT is compatible with the following accessories (for details, contact your agent): Antenna Battery Earphones • Turn off the HT, and then turn on the HT again. • Change the channel. Other accessories • Press the pre-programmed VOX button. Remote speaker and microphone If the call admission tone function is activated, you can use a trigger word to initiate a call. Wait until the call admission tone (if activated) ends, and speak to the microphone. You can enable or disable the tone/prompt function if required. The emergency call tone cannot be disabled. 1. Charger Enable or Disable the Tone/Prompt Function Perform the following steps: If you hear a positive prompt tone, it indicates that the HT switches from current zone to the next zone in the zone list. If you hear a negative prompt tone, it indicates that the HT switches from the current zone to the last zone in the list. The following operations are limited to the HTs on which the VOX function is activated. For details, contact your agent or system administrator. Settings The default level is set to normal. With large noise reduction, the HT blocks useless calls and background noise. Calls from remote locations may also be blocked. Press the pre-programmed zone button. 2. Set the Noise Reduction Level You can adjust the noise reduction level to block useless calls with low signal strength or channels whose background noise levels are higher than normal. 1. Perform the following steps: 1. Press the pre-programmed prompt/tone function button. 2. If you hear a positive prompt tone, it indicates the tone/prompt function is enabled. If you hear a negative prompt tone, it indicates the function is disabled. Check the Battery Level You can check the battery level. If the LED indicator is lit red, it indicates that the battery is being charged. If the LED indicator is lit green, it indicates that the battery is fully charged. Perform the following step: Press the pre-programmed battery level button to check the battery level through the LED indicator. Perform the following steps: 1. Press the pre-programmed power level button. 2. If you hear a positive prompt tone, it indicates that the HT operates at a low power level. If you hear a negative prompt tone, it indicates that the HT operates at a high power level. 11 12 13 FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. PH520 U(2)
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Has XFA : No Tagged PDF : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Create Date : 2015:06:03 10:21:45+08:00 Metadata Date : 2015:07:27 17:28:37+08:00 Modify Date : 2015:07:27 17:28:37+08:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:f31fbd6c-155a-48d5-83fe-3233f1ca77ed Original Document ID : xmp.did:BBE54F76FAF1E311ABB8DACC6433B594 Document ID : xmp.id:958C623C9709E511B4B1F0AE2378BF0B Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:F1589B339409E511B4B1F0AE2378BF0B Derived From Document ID : xmp.did:C64EE1AF70EDE41199F7F036E8F5A8EF Derived From Original Document ID: xmp.did:BBE54F76FAF1E311ABB8DACC6433B594 Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2015:06:03 10:21:45+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 3 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools