ZTE Quick Start AT&T Wireless Home Phone And Internet Base Z700a AT T Updates QSG 1 7838
User Manual: ZTE AT&T Home Base™ | ZTE USA
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Quick Start Getting to Know Your Device Before You Begin AT&T Wireless Home Phone and Internet The AT&T Home Base uses the AT&T cellular network and DOES NOT use your home phone wall jacks. Your device should be located: • Where you have a strong signal from a cell tower, typically near a window or outside wall. Signal strength may vary in different parts of your home. • Near an electrical wall outlet. • I n the general area where you’ll be using your home phone, computer, or Wi-Fi enabled devices. Signal Strength Power Wi-Fi Voicemail Information (See “AT&T Home Base Manager” on reverse) WPS AT&T Home Base™ (See “User Guide”) Ethernet Telephone Ports On/Off Power Input For more information, refer to your User Guide, visit att.com/homebasesupport, or call AT&T Support at 1-800-331-0500. STEP 1: Set Up Your Device A Install the Back-up Battery 1. R emove the bottom of the device by pushing the entire cover in the direction of the arrow. B Turn on Your Device C 1. Plug the power cord into an electrical wall outlet. 2. C onnect the other end of the power cord into the Power Input port on the back of your AT&T Home Base. 3. P ress and hold down the round On/Off button for 3 full seconds until the power light stays steady green. Ports ait a few seconds for the signal strength light to turn on, while W your device connects to the cellular network. Confirm signal strength light is green for optimal performance. Yellow indicates a moderate signal and may be sufficient. Signal Strength 2. Insert the back-up battery. Battery On/Off 3. Replace the cover. Check the Wireless Signal Hold 3 seconds STEP 2: Connect Your Phone A Unplug Your Phone from the Wall Jack B The AT&T Home Base is not used with your home phone wall jack. NOTE: If you have a cordless phone, keep it plugged into a power outlet. Connect Your Phone to the Device Transferring a Phone Number from Your Prior Provider Plug your phone into the “Phone 1” port on the AT&T Home Base, using your existing phone cable or the included phone cable. NOTE: Do not plug the device into your home phone wall jack. Transferring a phone number can take about 4 days, so you should keep a phone plugged into your wall jack to receive calls on your old service (including 911) until your transfer completes. However, you can make calls immediately on your AT&T Home Base. Check transfer status at att.com/port. Important Phone Tips • V oicemail is included with your service. Dial “1” to set up and access. If you choose to use an answering machine instead, set it to fewer than 4 rings. • T o place phones throughout your home, use a cordless phone system with multiple handsets. Wall jacks are not used with the AT&T Home Base. C Place a Test Call Place a test call from your connected home phone. Make sure to dial the 10-digit phone number, including area code. For best results, place the cordless phone base at least 12 inches from the AT&T Home Base. STEP 3: Connect to the Internet A Select Your Internet Connection B To Connect via Wi-Fi: 1. Open the Wi-Fi network manager on your computer or Wi-Fi enabled device. 2. Find and select the AT&T Home Base Wi-Fi network name (SSID) (e.g., ATT-HOMEBASE-XXXX). Enter Wi-Fi Network Password AT&T Home Base Manager When prompted, enter the Wi-Fi password found on the bottom of the AT&T Home Base. To customize your device or view important messages about your device and data usage, use the AT&T Home Base Manager. On any device connected to the AT&T Home Base, enter http://att.homebase directly into your browser address field and use “attadmin” as your login. NOTE: The information light will blink green when you have a message. Wi-Fi Access Use the following information to connect to the Internet: Network Name: ATT-HOMEBASE-XXXX Password: XXXXXXXX Helpful service information: The light will blink green when you have an important message from AT&T about your service plan. On any device connected to the AT&T Home Base, go to: URL: http://att.homebase Login: attadmin Wi-Fi Networks ATT-HOMEBASE-XXXX Other Network Guest WiFi Free Public WiFi To Connect via Ethernet: Use an Ethernet cable (not included) to connect your computer or other device to the Ethernet port on the back of your AT&T Home Base. Go to att.net (or your favorite website) to confirm your Internet connection. Skip Steps 3B and 3C. C Confirm Internet Connection Go to att.net (or your favorite website) to confirm your Internet connection. When your device is transmitting to and from the Internet, the Wi-Fi light will flicker green. Email Setup (Optional) To set up a free AT&T email account, go to att.net/signup and select Start Now. AT&T Home Base™ (“Home Base”) is a mobile device. It may be used in the U.S. with home phone equipment, computers, and other Wi-Fi compatible devices. For emergency calls, you may have to provide your location address to the 911 operator. Home Base has a back-up battery in the event of a power outage. However, a cordless phone connected to the Home Base will not operate (including 911) during a power outage. To use backup battery power, you must plug a corded phone into the Home Base. Corded or other landline phone equipment and Internet capable devices (e.g. PCs, tablets) not provided with service. Provides voice and wireless data service. Not compatible with wireless messaging services, security systems, fax services, medical alert and monitoring systems, credit card machines, IP/PBX Phone systems, or dial-up Internet service. May not be compatible with DVR/Satellite systems; please check with your provider. DSL customers should contact their provider before transferring a phone number to ensure uninterrupted DSL Internet service. Home Base sold for use on the AT&T wireless network and cannot be activated on other carriers’ wireless networks. If your Home Base is roaming, AT&T’s off-net usage restrictions apply. Service provided by AT&T Mobility. © 2016 AT&T Intellectual Property. All rights reserved. AT&T is a registered trademark 081704100558 of AT&T Intellectual Property.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c111 79.158366, 2015/09/25-01:12:00 Format : application/pdf Title : Quick Start - AT&T Wireless Home Phone and Internet - AT&T Home Base Description : Quick Start - AT&T Wireless Home Phone and Internet - AT&T Home Base Create Date : 2016:03:10 13:17:31-05:00 Metadata Date : 2016:03:10 13:17:36-05:00 Modify Date : 2016:03:10 13:17:36-05:00 Creator Tool : Adobe InDesign CC 2015 (Macintosh) Instance ID : uuid:ea64a01c-8d63-1b4e-8c8f-36fb1f6b27f4 Original Document ID : xmp.did:F77F1174072068118DBBBF7D410B73EE Document ID : xmp.id:b8b45466-b30f-4268-ae23-89b2d9752d9d Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:bf110261-1b78-456f-9a0e-730bc91387cb Derived From Document ID : xmp.did:92FDF5B134206811822AF471F7191956 Derived From Original Document ID: xmp.did:F77F1174072068118DBBBF7D410B73EE Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Macintosh) History Changed : / History When : 2016:03:10 13:17:31-05:00 Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 2 Creator : Adobe InDesign CC 2015 (Macintosh) Subject : Quick Start - AT&T Wireless Home Phone and Internet - AT&T Home BaseEXIF Metadata provided by EXIF.tools