Manual
Check your system requirements
1. Check you have a spare USB port (USB 1.0 or 2.0)
2. You need to be running Windows 2000 / XP / Vista for a
PC or OS X 10.5 and above for a Mac
3. The recommended system requirements are:
CPU 1GHz Pentium or above
Hard Disk 20GB or above
RAM 512M or above
Display 800 x 600 minimum
4. You need to have Administrator rights to install and run
the software
5. We suggest you switch off your anti-virus software before
installing the USB modem. In some cases protection
software can prevent automatic installation. It is possible
to start the installation process manually by clicking the
Autorun icon when it appears.
1
Get to know your USB Modem
1 3 5
4 6
2
1. LED Indicator 2. Rotating USB plug
3. External Antenna Port 4. Back cover
5. SIM Slot 6. MicroSD Slot
2
Insert your SIM Card
1. Open the slider panel on the back of your USB modem.
2. Insert your USIM card carefully as shown.
3. If you want to add a memory card you can do it now. Your
USB modem supports up to 4GB MicroSDHC memory.
4. Close the back cover.
Tip
Remember to keep your plastic SIM card holder. It has a
record of your phone number and a PIN number which you
will need later.
3
Insert the modem into your computer
The installation and management software is pre-loaded onto
your USB modem. Simply insert your modem into your
computer and follow the instructions on-screen. You’ll be up
and connected in about 5 minutes.
The USB modem is a Plug and Play device. Once inserted
your system will automatically detect the new hardware and
start to install the software. Be patient as it may take some
time for your computer to recognise the modem.
If nothing happens your system configuration may be
preventing Autorun.
Tips to resolve
z Windows users: Double click the Autorun icon to start the
software installation
z MAC users: Open the CD-ROM, ZTE MODEM, and double
click Telstra Turbo Connection Manager icon.
4
The installation method shown below is for Windows XP.
Other systems will follow a similar but not necessarily identical
installation process:
5
Choose ‘I accept….’, and then click Next to continue.
6
Press Next to accept the default folder location, or press
Change to define your own path.
7
Please wait a few seconds for the installation to proceed…
Click Finish to complete the installation.
8
Connect to the internet
After installation the software interface will launch
automatically. Your modem will continue installing for a couple
of minutes.
You’ll be ready to go as soon as you see the Connect button.
9
LED indicator Modem Status
Red Offline.Not registered on the network
Green solid Registered on the 2G network
Green blinking Active data transfer on the 2G network
Blue solid Registered on the 3G network
Blue blinking Active data transfer on the 3G network
z The installation will create a new shortcut on your desktop
and a new program listing under Start-Programs
z You may have to reboot your PC or MAC after installation
is complete
z If you have problems with the installation please contact
your supplier or see our website, www.zte.com.au/ for more
assistance and FAQ’s
z If you can’t connect to the internet check your SIM card is
inserted correctly, contact your service provider and check
your account is active.
10
Using your USB Modem
z Press Connect to establish a data connection using your
USB modem
z Launch your browser or other software
z When you have finished your internet or email connection
remember to return to the software interface and press
Disconnect to end your session
z If the software has been minimized then double click the
small icon on the task bar to re-open the application
window. See the task bar icon descriptions on Page 15.
TIP
After the computer wakes from hibernation or standby mode
you may need to remove and insert the modem.
11
Connected State
Note: The modem is locked to Telstra. If you use a SIM card
from another provider you may not be able to connect to the
network. Consult Telstra for more details or to unlock your
device.
12
Safe Removal of Hardware
To remove your USB modem from the computer first close
the Connection Manager then use the safe removal of
hardware process. If you remove the USB modem when it is
active the modem software and related information (eg
Phonebook records) may become corrupted.
Safely remove the modem
z Eg in Windows XP, left click the icon on the Windows
taskbar
z Click on Safely Remove Hardware
z Remove the USB modem.
13
Using the Card Manager Software
System Icons
Network signal strength
New SMS message
Red Computer icon - internet Not Connected
Green Computer icon - Internet Connected
Connection - P is packet-switched, C is circuit switched
Green arrow icon - modem inserted into the computer
Red arrow icon - modem not inserted into the computer
Orange arrow icon - modem is offline
Green SIM icon – SIM/USIM card is inserted
Red SIM icon - SIM/USIM card is not inserted
Current network connection type
14
Task Bar Information
When you minimize the software the window will minimize
to an icon on the system tray. The program is still active in
the background but disappears to free your normal Windows
space. Double click the task bar icon to resize the display.
Task bar icons
Green - Modem is inserted into the computer
Red - Modem is not inserted into the computer
Orange - Modem is Offline
Red - SIM/USIM card is not inserted
No network signal
There is a new message
Modem is ready to connect to Internet
Green - Internet is Connected
15
Task bar menu
Right Click the task bar icon to access the following menu:
Device offline Disconnect the modem from the networ
k
Device online Connect the modem to the network
Factory Settings Restore the modem settings to
their original values
Help Enter the Help interface
About View software and hardware versions
Exit Close the software and switch off the
modem
16
Internet connection records
From the Connect screen press Internet Connection Records
to show your connection history.
The internet connection records are for information only.
17
SMS Interface
Click the SMS icon to use the SMS Interface:
18
Read Incoming Messages
Click the Inbox button to read your received messages.
19
Create a new message
z Click New Message and enter the recipient’s number
z The recipient’s number can be entered directly or by
selecting entries from the Phonebook
z Use ‘;’ to separate multiple recipients.
20
z Click into the text field to enter text
z The SMS can be up to 140 characters, including symbols
z The interface will show total characters used
z Click Send to send the message. The prompt screen below
will appear:
z Select Yes to confirm
z After the message has been sent successfully it will be
saved in the Outbox
z If the message fails to send it will be saved in Drafts.
21
Read Read the selected SMS
Reply Reply to the selected SMS
Forward Forward the SMS to other recipients
Move Save the SMS on the PC or SIM card
Delete Delete the selected SMS
Save Save the phone number from the message to
the contacts phonebook
Cancel Return to the SMS interface
SMS General Features
Enter any of the Inbox / Outbox / Drafts to use the tabs at the
bottom of the window:
Notes
z If you want to select several messages, you can use the
Ctrl or Shift keys (Windows)
z New messages cannot be received when the SIM card is
full
z The system will indicate the SIM card is full. Messages
cannot be saved until some are deleted by the user.
22
PhoneBook
Click the PhoneBook button to select the phonebook interface.
23
To create a new contact click New
New Contact, enter the
details and select OK to finish.
You can choose the Save location as the PC or the USIM
card.
24
PhoneBook Notes:
z If your stored location (Folder) is PC then you can also
create a new Group
z To create a new group: Click New
New Group and enter
the group name
z Select contacts from the list on the right and drag them to
the group location
If a contact is selected, you can carry out the following
additional steps using the tabs on the bottom of the screen:
View View the selected contact’s information
Delete Delete contacts or groups
SMS Send messages to the mobile phone
number selected
Save as Save the contact information to a TXT file
on your PC
Edit Edit the contact information
25
Settings
Click the Settings button to select the settings interface
Connection Settings:
26
There is no need to change these settings as they are pre-
configured for your network. If you change networks or are
roaming you may need to modify some settings. Consult
your service provider for more information.
New Connection for Corporate Users and IT Administrators
If you have a private VPN you will need to create a new
connection configuration. This feature is designed for IT
Administrators in a corporate environment and is generally
not required to be changed by end users.
Add Add new configuration files
Delete Delete the selected configuration file
Edit Edit the selected configuration file
Set Default Set the selected profile as
your default connection
27
Security Settings
PIN enable - The PIN code is provided with your SIM card.
Consult your service provider if you forget your PIN.
Backup Contacts, Messages and Connection Records
Create a local backup of Phonebook and SMS data.
28
Network Settings
These settings are pre-configured for your network. Consult
your service provider for more information.
29
Message Settings
These settings are pre-configured for your network. If you
change networks or are roaming you may need to modify
some settings. Consult your service provider for more
information.
30
MicroSD card
If you use a MicroSD card in your modem your computer will
display a removable disk related to the MicroSD card. You
can then use the modem as a flash drive to store and transfer
files.
MicroSD cards supported to 2GB are FAT 16 format.
MicroSD HC cards supported to 4GB are FAT 32 format.
If you want to remove the modem please use the Safe
Removal of Hardware to stop the removable disk first. For
more details see the Safe Removal of Hardware process.
External Antenna Port
Only use the correct antenna as recommended by the
manufacturer. Insert and remove the connection carefully.
Do not pull on the cable to remove the connection.
Help
Click Help button to access the system help and
user guide.
31
Troubleshooting
If you have any problems with your connection or modem
please consult the manual and check this section. If the
problem still exists contact your service provider or check
our website for more details at www.zte.com.au
Problem Possible Causes Suggested Solution
The user inter-
face doesn’t
start after the
modem is
plugged in.
PC configuration
is not correct.
(No autorun)
Start the program
manually by going
Start
Program Files
or use the shortcut on
the desktop.
The modem
has no signal.
The antenna is at
the wrong angle
or position.
Adjust the angle and
position of the USB
modem.
You have no
network coverage.
Try moving location
until you get good
reception.
32
Problem Possible Causes Suggested Solution
The modem
has no signal.
You have not en-
tered your PIN
number at start
up
Restart the application
and enter your PIN
number. If the PIN is
invalid you cannot con-
nect to the network.
Message sent
failed.
The SMS centre
number isn’t
correct.
Check with your with
service provider and
enter the correct num-
ber in the Message
settings.
Data
connection
failed.
You have no
network coverage.
Try moving location
until you get good
reception.
The APN
configuration is
wrong
Check with your ser-
vice provider and set
the APN in the con-
figuration settings.
33
Problem Possible Causes Suggested Solution
Data
connection
failed.
The manual net-
work selection is
wrong.
Select the correct net-
work for your service
provider. Restore Au-
tomatic mode.
You are using the
wrong APN.
Consult your network
provider
The modem
cannot connect
to the internet
when overseas
You don’t have
international
roaming enabled
on your plan.
Consult your service
provider before you go
overseas to enable
roaming.
No warning
tone
The PC
soundcard is dis-
abled or on low
volume
Check the audio card
and adjust the volume.
The MicroSD
card cannot be
read or is not
found.
Re-insert the
MicroSD card.
The maximum ca-
pacity is 4GB
SDHC card
Try another MicroSD
card and make sure
the capacity and for-
mat is correct.
34
Software Removal
If you wish to uninstall the application please follow the
procedure below:
Start
Programs
Telstra Turbo Connection Manager
Uninstall
Follow the prompts and press Yes to continue.
MAC Users - drag the application folder to the Trash bin.
35
Precautions and Safety Information
z Some electronic devices are susceptible to
electromagnetic interference. The modem is a transmitting
device and may cause interference to sensitive electronic
equipment such as audio systems, vehicle systems and
medical equipment. Please consult the manufacturer of
the other device before using the modem.
z Operating of laptop or desktop PCs with the modem may
interfere with medical devices like hearing aids and
pacemakers. Please keep the modem more than 20
centimetres away from such medical devices. Turn the
modem off if necessary. Consult a physician or the
manufacturer of the medical device before using the
modem near such devices.
z Be aware of the regulations when using the modem at
places such as oil warehouses or chemical factories,
where there are explosive gases or explosive
products being processed. Turn off your modem as
instructed.
z Don’t touch the antenna area unnecessarily whilst
connected. This can affect your modem performance and
reduce the signal quality.
z Store the modem out of the reach of children. The modem
may cause injury or get damaged.
36
z The modem contains sensitive electronic circuitry. Do not
expose the modem to any liquids, high temperatures or
shock.
z Only use original accessories or accessories that are
authorized by the manufacturer. Using unauthorized
accessories may affect your modem’s performance,
damage your modem and violate related national
regulations.
z Avoid using the modem in areas that emit electromagnetic
waves or in enclosed metallic structures eg lifts.
z The modem is not waterproof. Please keep it dry and store
it in a cool, dry place.
z Don’t use the modem immediately after a sudden
temperature change eg from an air conditioned environment
to high temperature and humidity outside. In such cases
there could be condensing moisture inside the modem
which can cause internal damage. Unplug the modem and
leave it for 30 minutes before use.
z Always handle the modem with care. Be careful not to
drop or bend the modem.
z There are no user serviceable parts inside the modem.
Unauthorised dismantling or repair will void the warranty.
37
Radiation from Electronic Devices
The USB Wireless modem is a transmitting device with
similar output power to a mobile phone. It uses an internal or
external antenna to connect to the mobile network. To get
the best performance from your device do not cover or shield
the device in any way as this will lead to increased output
power. Always leave a clear space around the device to allow
the transmit and receive signals to propagate. SAR test have
been completed according to the Australian regulatory
requirements.
Declaration of Conformity
We declare under our sole responsibility that the product(s)
detailed in this manual, and in combination
with our accessories, conform with the essential
requirements of The Radio Communications Standard
(Electro-magnetic Radiation Human Exposure) 2003 and the
Australian Communications and Media Authority Section
376 of the Telecommunications Act 1997.
N14945
38
Radio Frequency (RF) Energy
This model MF633+ meets the government’s requirements
for exposure to radio waves.
This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy
set by the Federal Communications Commission of the U.S.
Government:
The exposure standard for wireless devices employs a unit
of measurement known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC is 1.6W/kg. *Tests for
SAR are conducted using standard operating positions
accepted by the FCC with the device transmitting at its
highest certified power level in all tested frequency bands.
Although the SAR is determined at the highest certified
power level, the actual SAR level of the device while
operating can be well below the maximum value. This is
because the device is designed to operate at multiple power
levels so as to use only the poser required to reach the
network. In general, the closer you are to a wireless base
station antenna, the lower the power output.
The highest SAR value for the model device as reported to
the FCC when worn on the body, as described in this user
guide, is 1.16 W/kg (Body-worn measurements differ among
device models, depending upon available enhancements
and FCC requirements.)
39
While there may be differences between the SAR levels of
various devices and at various positions, they all meet the
government requirement.
The FCC has granted an Equipment Authorization for this
model device with all reported SAR levels evaluated as in
compliance with the FCC RF exposure guidelines. SAR
information on this model device is on file with the FCC and
can be found under the Display Grant section of
http://www.fcc.gov/oet/fccid after searching on
FCC ID: Q78-ZTEMF633PLUS.
For body worn operation, this modem has been tested and
meets the FCC RF exposure guidelines for use when
plugged into a laptop PC, positions the handset a
maximum of 0.5 cm from the body. Use of other
enhancements may not ensure compliance with FCC RF
exposure guidelines.
40
FCC Compliance
z This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
z This device has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician
for help.
Caution:
Changes or modifications not expressly approved by the
party responsible for compliance could void the user‘s
authority to operate the equipment.
z The antenna(s) used for this transmitter must not be co-
located or operating in conjunction with any other antenna
or transmitter.
42
Technical Specifications
Network and
Band compat-
ibility
HSUPA/HSDPA/UMTS 850 MHz
HSUPA/HSDPA/UMTS 1900 MHz
HSUPA/HSDPA/UMTS 2100 MHz
GSM/GPRS/EDGE 850 MHz
GSM/GPRS/EDGE 900 MHz
GSM/GPRS/EDGE 1800 MHz
GSM/GPRS/EDGE 1900 MHz
Dimensions 86.5mm x 26.6mm x 10.4mm
Weight Approx. 26g
Data Rate
HSUPA Mode up to 5.76Mbps*
HSDPA Mode up to 7.2Mbps*
UMTS Mode up to 384 Kbps*
EDGE Mode up to 236.8 Kbps*
GPRS Mode up to 57.6 Kbps*
Voltage 5V
Current
Consumption
Resting: 100mA rms
Max: 450mA rms
43
Max Emitted
Power
In 3G WCDMA Mode: 250mW
In 2G GSM/GPRS Mode: 2W
Interface USB 2.0
Operating
systems
Windows 2000 SP4, XP SP2, SP3,
Vista
Apple MAC OS X 10.5 and above
Functions High speed wireless data, internet,
MicroSD card, SMS
MicroSDHC
memory card
4GB capacity on MicroSDHC card 2GB
on MicroSD
Temperature
Range
0ºC to +55ºC
* Actual speeds will be less. Speeds may vary due to
congestion, distance from the cell, local conditions, hardware,
software and other factors.
44