ZTE ZXCBTS802T CDMA Micro Base Transceiver Station User Manual

ZTE Corporation CDMA Micro Base Transceiver Station Users Manual

Users Manual

   ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & RF Remote Station     Installation Manual            ZTE CORPORATION
 ZXCBTS (V5.4) CDMA Micro Base Transceiver Station/RF Remote Station  Installation Manual    Manual Version    20050422-R1.1 Product Version   V5.4   Copyright © 2004 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation.      *   *   *   * ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P.R.China Website: http://www.zte.com.cn Postcode: 518057 Customer Support Center: (+86755) 26771900        800-9830-9830 Fax: (+86755) 26770801 Email: support@zte.com.cn *   *   *   * S.N.: sjzl20030272
FAX:+86-755-26770160 Suggestions and Feedback To improve the quality of ZTE product documentation and offer better services to our customers, we hope you can give us your suggestions and comments on our documentation and fax this form to +86-755-26770160; or mail to “Marketing center 3rd floor ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China”. Our postcode is 518057.   Document name  ZXCBTS (V5.4) CDMA Micro Base Transceiver Station/RF Remote Stations  Installation Manual Product version  V5.4  Document version  20050422-R1.1 Equipment installation time   Your information Name   Company  Postcode   Company address  Telephone   E-mail  Presentation: How is information presented? (Introductions, procedures, illustrations, others)  F Good       F Fair       F Average       F Poor       F Bad Accessibility: Can you find the information you want? (Table of contents, Index, headings, numbering, others)  F Good       F Fair       F Average       F Poor       F Bad Your evaluation of this documentation Intelligibility: Can you understand it when you find it? (Language, vocabulary, readability, others)  F Good       F Fair       F Average       F Poor       F Bad Presentation: Accessibility: Your suggestions for improvement of this documentation Intelligibility: Your other suggestions on ZTE product documentation
 Preface About This Manual This manual presents the hardware installation procedures of ZXCBTS micro base transceiver stations (BTSs)/remote stations. It is one of ZTE manual series for CDMA cellular mobile communications system. It aims to providing guidance to the engineering personnel who install ZTE CDMA micro-BTS/remote stations, as well as offering reference for the equipment maintenance personnel. Correct hardware installation is the basis for reliable and normal running of the base transceiver stations, thus enjoying importance in engineering construction. To facilitate the installation, this manual is written following the sequence of actual hardware installation. First, it briefs the structure of the ZXCBTS products, which is helpful for the installation personnel to get familiar with the equipment. Next, it describes the equipment installation procedures in detail. Finally, it presents how to check the equipment after the installation. How to Use This Manual 1. Overview Introduces the basic structure, basic installation procedures and points for attention during installation of the micro-BTS/remote stations. 2. Preparations Introduces the preparations for the installation, including listing needed tools and checking the installation environment. 3. Open-box Inspection Introduces the procedures and cautions for opening boxes and inspecting the equipment. 4.  Installation of Cabinet Details the fixation and installation of the cabinet of the equipment. 5.  Installation of Power Supply System
 Details the installation of the power supply system of the equipment. 6.  Installation of Grounding System Details the installation of the grounding system of the equipment. 7.  Connection of Cables Details the check of internal cable connections between various modules, as well as type selection and connection of external cables. 8.  Installation of Primary Antenna Feeder System Details the installation of the antenna feeder system of the equipment, including the procedures of assembling feeder cable connectors, installing antenna, laying feeder cables, installing feeder cable window and grounding equipment. 9.  Installation of GPS antenna feeder system Details the installation of GPS antenna feeder system for the equipment, including the procedures of assembling feeder cable connectors and installing antenna. 10.  Installation of Internal Modules Details the installation of internal modules. 11.  Hardware Installation Check Presents how to check the hardware installation. 12.  Power-on and Power-off Presents the procedures of powering on/off the equipment. 13. Appendix Presents the equipment performance specifications, meaning of various indicators and connection of cables. Conventions 1. Notational Convention Angular brackets “< >” identify names of keys and buttons, and the information typed by an operator from a terminal. Square brackets “[ ]” indicate a man-machine interface, menu item, data list or field name. The symbol “→”
 separates a multi-level menu, for example, [File→New→Folder] indicates the [Folder] menu item under the [New] submenu of the menu [File]. 2.  Keyboard Operation Convention Format Description <Key>  Indicate a key or button name, for example, <Enter>, <Tab>, <Backspace>, and <a>. <Key1+Key2>  Press Key 1 and Key 2 at the same time. <key1, Key2>  Press Key1 first. Then release Key 1 and press Key 2. 3.  Mouse Operation Convention Format Description Click  Refers to clicking the primary mouse button (usually the left mouse button) once Double-click  Refers to quickly clicking the primary mouse button (usually the left mouse button) twice Right-click  Refers to clicking the secondary mouse button (usually the right mouse button) once. Drag  Refers to pressing and holding a mouse button and move the mouse 4.  Danger, Warning, Caution and Note Statements Note,  Caution,  Warning,  Danger statements are used throughout this manual to emphasize important and critical information. You must read these statements to help ensure safety and to prevent product damage.   Statement: The actual product may differ from what is described in this manual due to frequent update of ZTE products and fast development of technologies. Please contact the local ZTE office for the latest updating information of the product.
 FCC & IC STATEMENT Before using this CDMA Micro Base Transceiver Station & RF Remote Station, read this important RF energy awareness and control information and operational instructions to ensure compliance with the FCC and IC RF exposure guidelines.  NOTICE: Working with the equipment while in operation, may expose the technician to RF electromagnetic fields that exceed FCC rules for human exposure.  Visit the FCC website at www.fcc.gov/oet/rfsafety to learn more about the effects of exposure to RF electromagnetic fields.  Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user’s authority to operate the equipment. Any change to the equipment will void FCC and IC grant.  This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to the FCC and IC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.    For OUTDOOR use, a PNALE Antenna with a maximum gain of 17dBi is authorized for use with this unit. Outside antennas must be positioned to observe minimum separation of 2M (6.56 feet.) for 800MHz unit and 1.5M (4.92 feet.) for 1900MHz unit from all users and bystanders. For the protection of personnel working in the vicinity of outside (uplink) antennas, the following guidelines for minimum distances between the human body and the antenna must be observed.  The installation of an OUTDOOR antenna must be such that, under normal conditions, all personnel cannot come within 2M (6.56 feet) for 800MHz unit and 1.5M (4.92 feet) for 1900MHz unit from the outside antenna. Exceeding this minimum separation will ensure that the worker or bystander does not receive RF-exposure beyond the Maximum Permissible Exposure according to section 1.1310 i.e. limits for Controlled Exposure.
  -i-Contents 1 Overview..................................................................................................................................................1-1 1.1 Introduction to Micro-BTS ............................................................................................................1-1 1.2 Installation Overview.....................................................................................................................1-4 1.3 Installation Flow ............................................................................................................................1-5 1.4 Points for Attention ........................................................................................................................ 1-7 2 Preparations ............................................................................................................................................2-1 2.1 Installation Environment Check.....................................................................................................2-1 2.1.1 Checking Equipment Building Conditions..........................................................................2-1 2.1.2 Checking Indoor Environment............................................................................................2-1 2.1.3 Checking Power Supply System .........................................................................................2-2 2.1.4 Checking Grounding System ..............................................................................................2-2 2.1.5 Checking Relative Devices .................................................................................................2-2 2.2 Tools and Instruments ....................................................................................................................2-2 2.3 Technical Documents .....................................................................................................................2-3 3 Open-box Inspection...............................................................................................................................3-1 3.1 Checking Packing List and Goods .................................................................................................3-1 3.2 Packaging.......................................................................................................................................3-2 3.3 Open-box Procedures.....................................................................................................................3-2 4 Installation of Cabinet ............................................................................................................................4-1 4.1 Installation Flow ............................................................................................................................4-1 4.2 Installation Modes..........................................................................................................................4-2 4.2.1 Installing Cabinet on Pole ...................................................................................................4-2 4.2.2 Installing Cabinet on Wall...................................................................................................4-6
  -ii-5 Installation of Power Supply System .................................................................................................... 5-1 5.1 Introduction to Power Cables ........................................................................................................ 5-1 5.1.1 -48V DC Power Cable ........................................................................................................ 5-1 5.1.2 120V AC Power Cable........................................................................................................ 5-2 5.2 Connection of Power Cables ......................................................................................................... 5-2 5.3 Assembling Power Cable Connector ............................................................................................. 5-3 5.3.1 Assembling -48V DC Power Cable Connector................................................................... 5-3 5.3.2 Assembling 120V AC Power Cable Connector .................................................................. 5-5 6 Installation of Grounding System ......................................................................................................... 6-1 6.1 Introduction to the Grounding System........................................................................................... 6-1 6.2 Installing Grounding System ......................................................................................................... 6-2 6.2.1 Installing Outdoor Grounding Copper Busbar.................................................................... 6-2 6.2.2 Installing the Grounding System of Micro-BTS................................................................. 6-3 6.2.3 Installing Feeder Cable Grounding Kit............................................................................... 6-4 7 Connection of Cables.............................................................................................................................. 7-1 7.1 Checking Internal Cable Connections ........................................................................................... 7-1 7.1.1 Type and Configuration of Internal Cables......................................................................... 7-1 7.1.2 Connection of Internal Cables ............................................................................................ 7-3 7.2 Connecting External Cables .......................................................................................................... 7-3 7.2.1 Connecting Optical Fiber.................................................................................................... 7-3 7.2.2 Connecting Multi-carrier Interconnection RF Cables......................................................... 7-7 7.2.3 Waterproof Processing of Joints ......................................................................................... 7-8 7.2.4 Connection of Trunk Cables ............................................................................................... 7-9 8 Installation of Primary Antenna Feeder System.................................................................................. 8-1 8.1 Preparations ................................................................................................................................... 8-1 8.1.1 Installation Personnel.......................................................................................................... 8-1
  -iii-8.1.2 Installation Environment.....................................................................................................8-2 8.1.3 Security Measures ...............................................................................................................8-2 8.1.4 Installation Tools .................................................................................................................8-2 8.2 Composition and Installation Requirements of Antenna Feeder System .......................................8-3 8.2.1 Composition........................................................................................................................8-3 8.2.2 Technical Parameters...........................................................................................................8-5 8.3 Installation Flow ............................................................................................................................8-5 8.4 Installation of Antenna ...................................................................................................................8-6 8.4.1 Determining Installation Location ......................................................................................8-6 8.4.2 Installing Accessories of Directional Antenna ....................................................................8-7 8.4.3 Transporting and Raising Antenna ......................................................................................8-8 8.4.4 Installing and Adjusting Directional Antenna .....................................................................8-9 8.4.5 Installing and Adjusting Omni Antenna ............................................................................8-10 8.4.6 Connecting Jumper Cable with Antenna and Sealing Their Joint ..................................... 8-10 8.5 Installation of Feeder Cable Window........................................................................................... 8-11 8.6 Connection of Feeder Cable.........................................................................................................8-12 8.6.1 Determining Route for Feeder Cable ................................................................................8-13 8.6.2 Assembling Connectors of Primary Feeder Cable ............................................................8-13 8.6.3 Cutting Feeder Cable.........................................................................................................8-16 8.6.4 Raising Primary Feeder Cable...........................................................................................8-17 8.6.5 Laying and Fastening Primary Feeder Cable ....................................................................8-18 8.6.6 Connecting Jumper Cable with Feeder Cable and Sealing Their Joint .............................8-20 8.6.7 Leading Primary Feeder Cable into Equipment Room .....................................................8-21 8.6.8 Connecting Indoor Jumper Cable......................................................................................8-23 8.7 Grounding System of Micro-BTS................................................................................................8-23 8.8 Test of Antenna Feeder System....................................................................................................8-26
  -iv-8.9 Waterproof Processing of Connectors.......................................................................................... 8-26 9 Installation of GPS Antenna Feeder System ........................................................................................ 9-1 9.1 Preparations ................................................................................................................................... 9-1 9.1.1 Installation Personnel.......................................................................................................... 9-1 9.1.2 Installation Environment..................................................................................................... 9-1 9.1.3 Security Measures............................................................................................................... 9-2 9.1.4 Installation Tools................................................................................................................. 9-2 9.2 Composition of GPS Antenna Feeder System ............................................................................... 9-3 9.3 Installation Procedures................................................................................................................... 9-3 9.4 Test of Antenna Feeder System...................................................................................................... 9-5 10 Installation of Internal Modules........................................................................................................ 10-1 10.1 Overview ................................................................................................................................... 10-1 10.1.1 Logical Positions of Equipment Modules....................................................................... 10-1 10.1.2 Layout of Internal Modules ............................................................................................ 10-2 10.1.3 Functions of the Modules ............................................................................................... 10-4 10.2 Module Installation Flow........................................................................................................... 10-7 10.3 Installation and Replacement of Modules.................................................................................. 10-8 10.3.1 Installation Sequence...................................................................................................... 10-8 10.3.2 Table of Cable Connections ............................................................................................ 10-8 10.3.3 Fastening and Bundling of Internal Cables..................................................................... 10-9 10.3.4 Installation of OIM ....................................................................................................... 10-11 10.3.5 Installation of LFM....................................................................................................... 10-12 10.4 Points for Attention.................................................................................................................. 10-12 11 Hardware Installation Check..............................................................................................................11-1 11.1 Checking Components in the Cabinet........................................................................................ 11-1 11.2 Checking the Cabinet................................................................................................................. 11-1
  -v-11.3 Checking Cables......................................................................................................................... 11-2 11.4 Checking Power Cables and Grounding Cables......................................................................... 11-2 11.5 Checking T1 Cables ................................................................................................................... 11-4 11.6 Checking Indoor 1/2” Jumper Cables ........................................................................................11-4 11.7 Checking Primary Feeder Cables and GPS Feeder Cables ........................................................11-5 11.8 Checking Water-blocking Curve for Feeder Cable Window and Primary Feeder Cables.......... 11-6 11.9 Checking Hangers ...................................................................................................................... 11-6 11.10 Checking Outdoor 1/2” Jumper Cables.................................................................................... 11-7 11.11 Checking Antenna .................................................................................................................... 11-7 11.12 Checking Standing Wave Ratio of Feeder Cables.................................................................... 11-9 11.13 Checking Indoor and Outdoor Environment ............................................................................11-9 12 Power-on and Power-off .....................................................................................................................12-1 12.1 Checking Components in the Cabinet before Power-on ............................................................12-1 12.2 Checking External Cables before Power-on ..............................................................................12-2 12.3 Powering on/off the Cabinet ......................................................................................................12-2 13 Installing the Integrated Micro-BTS.................................................................................................13-1 13.1 Introduction to the Solution of Micro-BTS Integration .............................................................13-1 13.1.1 Implementation of the Micro-BTS Integration ...............................................................13-1 13.1.2 Micro-BTS Integration Solution .....................................................................................13-2 13.1.3 Module Layout of the Integrated Micro-BTS and RF Remote Station ...........................13-4 13.1.4 Networking Modes of the Integrated SDH......................................................................13-7 13.2 Installing the Built-in SDH of Micro-BTS.................................................................................13-7 13.2.1 Position and Internal Connection of the Built-in SDH in the Micro-BTS ......................13-7 13.2.2 Connecting the External Optical Fibers and Cables During Installation.........................13-8 13.3 Installing the Integrated UPS of Micro-BTS/RF Remote Station ............................................13-10 13.3.1 Introduction to ZXUPS L010........................................................................................13-10
  -vi-13.3.2 Precautions for UPS Installation................................................................................... 13-11 13.3.3 Structural Feature and Installation Mode of UPS ......................................................... 13-12 13.3.4 Installing the Engineering Cables of L010UPS ............................................................ 13-13 13.3.5 Installing UPS............................................................................................................... 13-14 13.4 Installing the Ancillary Combinational Power Supply of Micro-BTS/RF Remote Station ..... 13-15 13.4.1 Installing the Outdoor Power Box ................................................................................ 13-15 13.4.2 Installing the Outdoor Battery Box............................................................................... 13-17 13.4.3 Cable Connection for Outdoor Power Box................................................................... 13-17 Appendix A Packaging, Storage and Transportation ............................................................................ A-1 A.1 Packaging..................................................................................................................................... A-1 A.2 Storage ......................................................................................................................................... A-1 A.3 Transportation .............................................................................................................................. A-2 Appendix B Table of Cable Connections .................................................................................................B-1 B.1 Cable Connections in M800T Single-carrier Micro-BTS .............................................................B-1 B.2 Cable Connections in M800T Double-carrier Micro-BTS............................................................B-2 B.3 Cable Connections in R800T Single-carrier Remote Stations ......................................................B-3 B.4 Cable Connections in R800T Double-carrier Remote Stations.....................................................B-5 B.5 Cable Connections in M190T Single-carrier Micro-BTS .............................................................B-6 B.6 Cable Connections in M190T Double-carrier Micro-BTS............................................................B-7 B.7 Cable Connections in R190T Single-carrier Remote Stations ......................................................B-8 B.8 Cable Connections in R190T Double-carrier Remote Stations.....................................................B-9 B.9 Cable Connections in M802T Single-carrier Micro-BTS ...........................................................B-10 B.10 Cable Connections in M802T Double-carrier Micro-BTS........................................................B-12 B.11 Cable Connections in R802 Single-carrier RF Remote Stations ...............................................B-13 B.12 Cable Connections in R802T Double-carrier Remote Stations.................................................B-14 B.13 Cable Connections in M191T Single-carrier Micro-BTS .........................................................B-15
  -vii-B.14 Cable Connections in M191T Double-carrier Micro-BTS....................................................... B-16 B.15 Cable Connections in R191T Single-carrier Remote Stations.................................................. B-18 B.16 Cable Connections in R191T Double-carrier Remote Stations ................................................ B-19 B.17 Cable Connections in M192T Single-carrier Micro-BTS......................................................... B-20 B.18 Cable Connections in M192T Double-carrier Micro-BTS....................................................... B-21 B.19 Cable Connections in R192T Single-carrier Remote Stations.................................................. B-22 B.20 Cable Connections in R192T Double-carrier Remote Stations ................................................ B-23 Appendix C Equipment Parameters .......................................................................................................C-1 C.1 Dimension .................................................................................................................................... C-1 C.2 Power Consumption ..................................................................................................................... C-1 Appendix D Indicators..............................................................................................................................D-1 D.1 BDM Indicators............................................................................................................................ D-1 D.2 Indicators on Front Panel of MGPS ............................................................................................. D-1 D.3 Indicators of LFM, RFM and OIM ..............................................................................................D-2 Appendix E Abbreviations ....................................................................................................................... E-1
  -i-A List of Figures Fig. 1.1-1    Structure of ZXCBTS M800T Micro-BTS.......................................................................1-2 Fig. 1.1-2    Structure of Remote Stations ............................................................................................1-3 Fig. 1.1-3    Connection between Remote Station and Macro-BTS .....................................................1-3 Fig. 1.1-4    Connection between Remote Station and Macro-BTS .....................................................1-4 Fig. 1.2-1    Schematic Diagram of the Hardware Installation of Micro-BTS/Remote Station ...........1-5 Fig. 1.3-1    Hardware Installation Flow Diagram ...............................................................................1-6 Fig. 3.2-1    Packing Box for ZXCBTS Cabinet ..................................................................................3-2 Fig. 3.3-1    Schematic Diagram for Opening a Box............................................................................3-3 Fig. 4.1-1    Flow of Installing the Cabinet ..........................................................................................4-2 Fig. 4.2-1    Schematic Diagram of Fastening the Cabinet onto the Pole (step 1) ...............................4-3 Fig. 4.2-2    Schematic Diagram of Fastening the Cabinet onto the Pole (step 2) ...............................4-4 Fig. 4.2-3    Schematic Diagram of Fastening the Cabinet onto the Pole (step 3) ...............................4-4 Fig. 4.2-4    Schematic Diagram of the Cabinet Fastened onto the Pole..............................................4-5 Fig. 4.2-5    Schematic Diagram of Installing the Support onto the Wall ............................................4-6 Fig. 4.2-6    Schematic Diagram of Installing the Cabinet onto the Wall............................................. 4-7 Fig. 5.1-1  Four-pin Connector and Four-core Power Cable .............................................................5-1 Fig. 5.2-1    Connection of Power Cables and Grounding Cables at the Bottom of a Cabinet............5-3 Fig. 5.3-1    Assembling a Power Cable Connector (step 1) ................................................................5-3 Fig. 5.3-2    Assembling a Power Cable Connector (step 2) ................................................................5-4 Fig. 5.3-3    Assembling a Power Cable Connector (step 4) ................................................................5-4 Fig. 5.3-4    Assembling a Power Cable Connector (step 5) ................................................................5-5 Fig. 5.3-5    Assembling a Power Cable Connector (step 6) ................................................................5-5 Fig. 6.1-1    Schematic Diagram of Grounding Connections...............................................................6-2
  -ii-Fig. 6.2-1    Appearance of a Grounding Copper Busbar .................................................................... 6-3 Fig. 6.2-2    Connection of Power Cable and PGND Cable at the Bottom of a Cabinet...................... 6-4 Fig. 6.2-3    Structure of a Grounding Kit............................................................................................ 6-5 Fig. 6.2-4    Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable............................................................................................................................................................. 6-6 Fig. 7.2-1    Structure of Optical Fiber (1) ........................................................................................... 7-3 Fig. 7.2-2    Structure of Optical Fiber (2) ........................................................................................... 7-4 Fig. 7.2-3    Structure of Optical Fiber (3) ........................................................................................... 7-5 Fig. 7.2-4    Structure of Optical Fiber (4) ........................................................................................... 7-5 Fig. 7.2-5    Schematic Diagram of Connecting Optical Fiber ............................................................ 7-6 Fig. 7.2-6    Connection of Interconnection RF Cables ....................................................................... 7-8 Fig. 7.2-7    Connection of T1 Cables.................................................................................................. 7-9 Fig. 8.2-1    Typical Structure of the Antenna Feeder System ............................................................. 8-4 Fig. 8.3-1    Antenna Installation Flow ................................................................................................ 8-6 Fig. 8.4-1    Installation of the KATHREIN Antenna .......................................................................... 8-7 Fig. 8.4-2    Schematic Diagram of Raising the Antenna to the Tower Top ........................................ 8-8 Fig. 8.4-3    Schematic Diagram of Adjusting the Pitch Angle of the Antenna ................................. 8-10 Fig. 8.5-1    Structure of a Feeder Cable Window ............................................................................. 8-12 Fig. 8.6-1    Structure of the Feeder Cable of a Micro-BTS/Remote Station..................................... 8-13 Fig. 8.6-2    Cutter for Assembling 7/8” Feeder Cable Connectors ................................................... 8-14 Fig. 8.6-3    Schematic Diagram of Cutting the Feeder Cable with the Cutter.................................. 8-14 Fig. 8.6-4    Schematic Diagram of Correct Cutting Size.................................................................. 8-14 Fig. 8.6-5    Schematic Diagram of Expanding the External Copper Conductor............................... 8-15 Fig. 8.6-6    Schematic Diagram of Connecting the Front Part with the Back Part of the Connector 8-15 Fig. 8.6-7    Schematic Diagram of Fastening the Front Part with the Back Part of the Connector .. 8-16 Fig. 8.6-8    Schematic Diagram of Pulling the Feeder Cable Up the Tower..................................... 8-18 Fig. 8.6-9    Appearance of a Hanger................................................................................................. 8-19
  -iii-Fig. 8.6-10    Schematic Diagram of Wrapping Waterproof Adhesive Tape (1)................................. 8-20 Fig. 8.6-11    Schematic Diagram of Wrapping Waterproof Adhesive Tape (2).................................8-21 Fig. 8.6-12    Schematic Diagram of Wrapping Waterproof Adhesive Tape (3)................................. 8-21 Fig. 8.6-13    Leading the Feeder Cable into the Equipment Room - Mode 1 ...................................8-22 Fig. 8.6-14    Leading the Feeder Cable into the Equipment Room - Mode 2 ...................................8-22 Fig. 8.7-1    Structure of a Grounding Kit ..........................................................................................8-24 Fig. 8.7-2    Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable...........................................................................................................................................................8-25 Fig. 9.2-1    Composition of the GPS Antenna Feeder System ............................................................9-3 Fig. 9.3-1    Schematic Diagram of Length of Cable Sheath to be Stripped ........................................9-4 Fig. 9.3-2    Schematic Diagram of Soldering the Core Wire with the Pin ..........................................9-4 Fig. 9.3-3    Structure of N-J7A............................................................................................................9-4 Fig. 10.1-1    Modules and Boards in M800T/M801T/M802T/M190T/M191T/M192T Micro-BTS10-1 Fig. 10.1-2    Modules and Boards in R800T/R801T/R802T/R190T/R191T/R192T ........................10-2 Fig. 10.1-3    Layout of Modules in a ZXCBTS Micro-BTS .............................................................10-3 Fig. 10.1-4    Layout of Modules in a ZXCBTS Remote Station.......................................................10-4 Fig. 10.2-1    Module Installation Flow Diagram...............................................................................10-7 Fig. 10.3-1    Schematic Diagram of Bundling Internal Cables (1)....................................................10-9 Fig. 10.3-2    Schematic Diagram of Bundling Internal Cables (2)..................................................10-10 Fig. 10.3-3    Schematic Diagram of Bundling Internal Cables (3)..................................................10-10 Fig. 10.3-4    Corresponding Relations between OIM Expansion Slots in BDM and Sectors .........10-11 Fig. 10.3-5    Schematic Diagram of Inserting the OIM into the BDM ...........................................10-12 Fig. 12.1-1    Setting of S1 .................................................................................................................12-1 Fig. 13.1-1 Solution (I) of Micro-BTS Integration ............................................................................13-3 Fig. 13.1-2 Solution (II) of Micro-BTS Integration ...........................................................................13-4 Fig. 13.1-3 Layout of Modules in the ZXCBTS micro-BTS .............................................................13-5 Fig. 13.2-1 Cable Layout of the Built-in SDH in the CDMA Micro-BTS.........................................13-8
  -iv-Fig. 13.2-3 Connection of the Optical Fiber .................................................................................... 13-10 Fig. 13.3-1 Appearance of the ZXUPS L010 Series........................................................................ 13-11 Fig. 13.3-2 Inner Structure of the ZXUPS L010 Series................................................................... 13-11 Fig. 13.3-4 Layout of the Monitoring Cables of the CDMA Micro-BTS 485/Dry Contact ............ 13-14 Fig. 13.4-6 Output Connecting Terminal of the Dry Contact .......................................................... 13-19 Fig. C.1-1    Appearance of a ZXCBTS Cabinet .................................................................................C-1 Fig. D.1-1    Indicators of the BDM.................................................................................................... D-1 Fig. D.3-1  Location of Indicators on the OIM Panel ...................................................................... D-4
  -i-A List of Tables Table 1.1-1  List of ZXCBTS Micro-BTS/Remote Stations (800MHz) ............................................1-1 Table 1.1-2  List of ZXCBTS Micro-BTS/Remote Stations (1900MHz) ..........................................1-1 Table 2.2-1  Tools and Instruments Needed for the Installation.........................................................2-2 Table 5.1-1  Corresponding Relationship between Core Wires and Binding Posts............................5-2 Table 5.1-2  Corresponding Relationship between Core Wires and Binding Posts............................5-2 Table 5.3-1  Corresponding Relationship between Core Wires and Binding Posts...........................5-6 Table 7.1-1  List of Types and Configurations of Internal Cables......................................................7-1 Table 13.2-1 Cable Connection of the Built-in SDH inside the CDMA Micro-BTS.........................13-7 Table 13.3-1 From-to-list of the CDMA Micro-BTS 485/dry contact supplementary cables..........13-13 Table B.1-1    Cable Connections in M800T Single-carrier Micro-BTS ............................................ B-1 Table B.2-1    Cable Connections in M800T Double-carrier Micro-BTS ........................................... B-2 Table B.3-1    Cable Connections in R800T Single-carrier Remote Stations...................................... B-3 Table B.4-1    Cable Connections in R800T Double-carrier Remote Stations .................................... B-5 Table B.5-1    Cable Connections in M190T Single-carrier Micro-BTS ............................................ B-6 Table B.6-1    Cable Connections in M190T Double-carrier Micro-BTS ........................................... B-7 Table B.7-1    Cable Connections in R190T Single-carrier Remote Stations...................................... B-8 Table B.8-1    Cable Connections in R190T Double-carrier Remote Stations .................................... B-9 Table B.9-1    Cable Connections in M802T Single-carrier Micro-BTS .......................................... B-10 Table B.10-1    Cable Connections in M802T Double-carrier Micro-BTS....................................... B-12 Table B.11-1    Cable Connections in R802T Single-carrier Remote Stations.................................. B-13 Table B.12-1    Cable Connections in R802T Double-carrier RF Remote Stations .......................... B-14 Table B.13-1    Cable Connections in M191T Single-carrier Micro-BTS......................................... B-15 Table B.14-1    Cable Connections in M191T Double-carrier Micro-BTS....................................... B-16
  -ii-Table B.15-1    Cable Connections in R191T Single-carrier Remote Stations ..................................B-18 Table B.16-1    Cable Connections in R191T Double-carrier Remote Stations.................................B-19 Table B.17-1    Cable Connections in M192T Single-carrier Micro-BTS .........................................B-20 Table B.18-1    Cable Connections in M192T Double-carrier Micro-BTS........................................B-21 Table B.19-1    Cable Connections in R192T Single-carrier Remote Stations ..................................B-22 Table B.20-1    Cable Connections in R192T Double-carrier Remote Stations.................................B-23 Table C.2-1    Power Consumption of Several Types of Micro-BTS and Remote Stations.................C-2 Table C.2-2    Power Consumption of Several Types of Micro-BTS and Remote Stations.................C-2 Table C.2-3    Power Consumption of Several Types of Micro-BTS and Remote Stations.................C-3 Table D.2-1  Indicators on the Front Panel of MGPS....................................................................... D-1 Table D.3-1    Indicators of the LFM.................................................................................................. D-2 Table D.3-2    Indicators of the RFM.................................................................................................. D-3 Table D.3-3    Indicators on the OIM Panel........................................................................................D-4
  1-11 Overview  Summary      Listing the components to be installed.    Describing the installation flow.    Presenting points for attention during the installation1.1 Introduction to Micro-BTS With the development of various new technologies, Base Transceiver Station (BTS) is oriented to be small and intelligent, with low power consumption, low cost and high reliability. In large or medium-sized cities, common micro-BTS cannot meet the demand of some busy-traffic areas due to the block of high buildings. In addition, it is a waste for micro-BTS to be installed in some remote areas with less traffic. Moreover, micro-BTS have high requirements on the equipment room environment. To avoid the above problems, ZTE has developed ZXCBTS products. ZXCBTS products are classified based on different frequency bands and transmitter powers. This manual serves for the installation of the following models: Table 1.1-1    List of ZXCBTS Micro-BTS/Remote Stations (800MHz)   Model Name Rated Transmission PowerZXCBTS  M800T  CDMA micro-BTS (800MHz)  10W ZXCBTS  M802T  CDMA micro-BTS (800MHz)  20W ZXCBTS    R800T  CDMA remote station (800MHz)  10W ZXCBTS    R802T  CDMA remote station (800MHz)  20W Table 1.1-2    List of ZXCBTS Micro-BTS/Remote Stations (1900MHz) Model Name Rated Transmission PowerZXCBTS  M190T  CDMA micro-BTS (1900MHz)  5W ZXCBTS  M191T  CDMA micro-BTS (1900MHz)  10W
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    1-2Model Name Rated Transmission PowerZXCBTS  M192T  CDMA micro-BTS (1900MHz)  20W ZXCBTS    R190T  CDMA remote station (1900MHz)  5W ZXCBTS    R191T  CDMA remote station (1900MHz)  10W ZXCBTS    R192T  CDMA remote station (1900MHz)  20W ZXCBTS products include micro-BTS and remote stations, working in the frequency bands of 800MHz and 1.9GHz. Micro-BTS system consists of Baseband Digital Subsystem (BDS), Timing & Frequency Subsystem (TFS), power supply subsystem, lightning protection subsystem and Radio Frequency Subsystem (RFS). The structure of M800T/M802T//M190T/M191T/M192T micro-BTS is illustrated in the following figure. BSC, macro-/micro-BTST1 (4) BDSsubsystem(BDM)RFS subsystem(MTRX, MPA,MLNA, MDUPand MDIV)TFSsubsystem(GPSTM) Power supplyGPS, RF antenna feeder and power lightningarresterGPS antenna RF antennaMicro-BTS Fig. 1.1-1    Structure of ZXCBTS M800T Micro-BTS Remote stations are similar to micro-BTS in structure, but different in replacing Baseband Digital Module (BDM) with Remote Fiber Module (RFM) and removing GPS Timing Module (GPSTM), for the clock signals of remote stations are demodulated from the signals sent through optical fiber. The structure of remote stations is illustrated in the following figure.
 Chapter  1  Overview  1-3RFM RFS (MTRX,MDUP and MDIV)PowersupplyRF antenna feeder and powerlightning arresterRF antennaOpticalfiber Fig. 1.1-2    Structure of Remote Stations Remote stations should cooperate with the macro-/micro-BTS to achieve the BTS functions, so you need to configure Local Fiber Module (LFM) on micro-BTS or Optical Interface Module (OIM) on micro-BTS for interworking with the remote stations. If the LFM is configured in a macro-BTS, the connection between the remote station and the macro-BTS is illustrated in the following figure. Macro-BTSRemote stationRFMLFMRFIMDIV DUPMLNA MLNAMTRXTXRXRX RXMPARXRX RXTXTXOptical fiber Fig. 1.1-3  Connection between Remote Station and Macro-BTS If the OIM is configured in a micro-BTS, the connection between the remote station and the micro-BTS is illustrated in the following figure.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    1-4Remote stationRFMDIV DUPMLNA MLNAMTRXRX RXTXTXRXRX RXMicro-BTSOIMBDMMPARXTXOptical fiber Fig. 1.1-4  Connection between Remote Station and Macro-BTS 1.2 Installation Overview The hardware installation of micro-BTS/remote stations can be divided into the following aspects: 1.  Installing shelf and boards, connecting internal cables and setting DIP switches 2.  Installing the power supply system 3.  Installing the grounding system 4.  Locating and installing the antenna, jumper cable and feeder cable, and testing the antenna feeder system 5.  Installing GPS and its feeder cables 6.  Connecting trunk cables and assembling their connectors 7.  Installing the alarm system for reporting abnormal temperature and humidity See Fig. 1.2-1.
 Chapter  1  Overview  1-5Install the GPSInstall the shelfCheck internalcablesSet the DIPswitchesInstall the ZXCBTS cabinetConnect trunkcablesInstall the powersupply systemInstall thegrounding systemInstall thesunshade coverInstall theantenna system Fig. 1.2-1  Schematic Diagram of the Hardware Installation of Micro-BTS/Remote Station 1.3 Installation Flow Install the equipment following the specified procedures strictly: 1.  Install the support; 2.  Locate the cabinet on the support; 3.  Secure the cabinet; 4.  Install the sunshade cover (necessary for outdoor installation); 5.  Connect power cables and grounding cables of the cabinet; 6.  Connect T1 cables of the cabinet; 7.  Install the primary antenna feeder system to connect with the RF cables; 8.  Install the GPS; 9.  Install and test the boards and modules, and set the DIP switches; 10.  Check the installation. See Fig. 1.3-1.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    1-6Engineering SurveyReportYesNoStartBTS EngineeringDesign andConstruction DrawingEnvironmentAcceptance ReportCabling rack   Powersupply systemGrounding systemOther accessoriesPreparation forengineeringinstallationCheck constructionconditionsOpen-box inspectionPacking list Goods arecorrectGoods Error FeedbackListGoods ReplacementFeedback ListInstall the shelfInstall the powersupply systemInstall thegrounding systemCheck cable connectionsin the shelfConnect trunk cablesCheck the primaryantenna feeder systemInstall the GPSSet DIP switchesHardware installationcheckEnd Fig. 1.3-1  Hardware Installation Flow Diagram
 Chapter  1  Overview  1-71.4 Points for Attention Pay attention to the following points during the installation: The installation personnel should be trained to obtain the qualification entitled by ZTE and read this manual before the installation. 1.  Do not operate on the cabinet or any module when the power is on. 2.  Observe the relative requirements strictly when installing the BTS. 3.  Do not install the antenna feeder system in thunder weather. 4.  Before the thunder storm season of each year comes, check whether the lightning arrester is in good condition and is well contacted. If it is damaged, replace it immediately. 5.  When the installation of the cabinet completes, lock the door immediately. If the door need be opened in case of maintenance, contact the professional personnel for help.
  2-12 Preparations  Summary      Describing the installation environment check.    Listing the installation tools.   Listing the technical documents needed for installation. 2.1 Installation Environment Check The items to check: 2.1.1 Checking Equipment Building Conditions Check if the layout, height, bearing capability, shock-proof ability, doors and windows, walls and troughs of the equipment building meet the requirements. 2.1.2 Checking Indoor Environment Check the temperature, humidity, air pressure, ventilation condition, antistatic protection measures, anti-interference measures, dustproof measures, rodent-resistant measures, fire-protection facility, lighting condition, water supply and drainage system of the equipment room. To the highest priority, the equipment should be installed on the cool and dry walls indoors with good ventilation; the fire-protection facility should be equipped; there should be no caustic gas or smog in the room and no leakage on the roof; the electromagnetic interference strength should be no more than 140dBµV/m (0.01MHz~110000MHz). Or the equipment can be installed on the shady walls outdoors with good ventilation and rain blocks. To the least priority, the equipment can be installed on common walls, towers or high poles. The operating temperature range of the equipment is between -40°C and +55°C, and the relative humidity range is between 5% and 100%.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    2-22.1.3 Checking Power Supply System Check the power supply ability and quality. A group of independent and stable 85V~138V (nominal 120V) AC power should be supplied to the equipment. It is prohibited to share the power supply with other high-power telecom equipment or the usually powered-down equipment. 2.1.4 Checking Grounding System The standard grounding system should be equipped and the resistance should be less than 5 ohm.   2.1.5 Checking Relative Devices Check if the other devices relative to the normal operation of the equipment are in good condition, such as interface device, transmission device, Digital Distribution Frame (DDF) and Optical Distribution Frame (ODF). 2.2 Tools and Instruments Prepare the tools and instruments needed for the installation in advance as listed in Table 2.2-1. Table 2.2-1    Tools and Instruments Needed for the Installation Type Name Special tools One cutter for assembling feeder cable connectors One 75-ohm coaxial cable stripper 75-ohm coaxial crimping plier One multi-functional crimping plier One multimeter One SiteMaster standing wave ratio tester   One earth resistance tester Drilling tools One percussive drill Several drill bits One cleaner One power connector board (with at least three two-pin and three-pin sockets respectively; the current capacity is more than 15 amp.)   General tools Three cross screw-drivers (4”, 6” and 8”) Three straight screw-drivers (4”, 6” and 8”) Four adjustable wrenches (6”, 8”, 10” and 12”)
 Chapter  2  Preparations  2-3Type Name Two spanners (17” and 19”) One hexagon spanner One socket wrench One 5kg nail hammer One 300W electric iron and one 40W electric iron One coil of solder wires Measurement tools One 50m tape measure One 5m steel tape measure One 400mm horizontal ruler One inclinometer One compass One multimeter Ruler One plumb Protection tools  Antistatic wrist strap Safety helmet, slip-proof gloves Locksmith tools One hacksaw, several saw blades One sharp nose plier (8”) One diagonal plier (8”) One slip joint plier (8”) One vice (8”) A set of files (middle) One tweezers One paint brush One scissors One dryer One solder removal tool One hydraulic pressure pliers One crowbar Assistant tools Pulley group Rope Ladder Forklift 2.3 Technical Documents Prepare the following technical documents: 1.  Engineering Survey Report, BTS Engineering Design and Construction Drawing, Environment Acceptance Report
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    2-4Engineering Survey Report should be filled by the technical engineers of the equipment provider during site survey. If they can not carry out the survey in time, you should survey the site, fill in the report and then send it to the equipment provider. This report is used for the preparation of construction materials. BTS Engineering Design and Construction Drawing should be prepared by the design unit you entrusted, and a copy should be provided to the equipment provider before the delivery. Environment Acceptance Report is used by the technical engineers of the equipment provider to check the construction environment during site survey. If any inconformity is found, you are required to solve the problem. Before the construction, the second check will be implemented. 2.  ZXCBTS(V5.4)CDMA Micro Base Transceiver Stations/RF Remote Stations Installation Manual, ZXCBTS(V5.4)CDMA Micro Base Transceiver Stations/RF Remote Stations Technical Manual, ZXCBTS(V5.4)CDMA Micro Base Transceiver Stations/RF Remote Stations Hardware Manual, ZXCBTS(V5.4)CDMA Micro Base Transceiver Stations/RF Remote Stations Maintenance Manual 3.  Installation Acceptance Report, Test Acceptance Report Installation Acceptance Report and Test Acceptance Report should be offered to you by the equipment provider during delivery. Installation Acceptance Report is filled after the BTS installation completes. Test Acceptance Report is filled during the BTS commissioning.
  3-13 Open-box Inspection  Summary      Describing the inspection procedures.    Describing the open-box procedures. 3.1 Checking Packing List and Goods  Caution Because ZXCBTS equipment is expensive, ensure that it is packed well and the flags for avoiding water and vibrations are marked. Load and unload the equipment gently, and avoided damage from sunshine and rain. 1.  Check the “ZTE delivery sheet”. 2.  Open-box inspection should be done by the engineering supervisor and your representative. First, check if the total quantity of the goods is correct according to the packing list, if the packing boxes are in good condition, and if the delivery location is the right installation site. 3.  Next, open the boxes and the engineering supervisor should check the goods based on the packing list. Open-box Inspection Report is put in the packing box numbered 1#. Open the 1# box and take out the Open-box Inspection Report to check if the total quantity of the goods is consistent with the checklist, and then archive the report. 4.  During the inspection, if loss of goods, lack of goods, error delivery or any damage is found, find out the cause and feedback to the ZTE headquarter for handling. 5.  The goods are packed in either cartons or wooden boxes. You need to open them on site using different tools.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    3-23.2 Packaging  Note The cabinets of micro-BTS and remote stations are the same in structure, so is the packaging method. Put the support and other accessories of the ZXCBTS cabinet into the wooden box. In the wooden box, the cabinet is packed with foam boards, a bubble bag and a plastic bag. After opening the box, you need not uplift it but directly take the equipment out. When carrying the box, be cautious to prevent the cabinet from being damaged. The packing box for the ZXCBTS cabinet is shown in Fig. 3.2-1. CDMA micro-BT SZTE CORPORATIONZTE Plaza, Keji Road South, Hi-Tech IndustrialPark, Nanshan District, Shenzhen, P.R.ChinaPostcode: 518057Tel: (+86755) 6790000Cust omer Support Center: 8008301118Goods:Net Weight:                (Kg)Volume:      81x52x40  (cm)Qty.:Packing List: Fig. 3.2-1    Packing Box for ZXCBTS Cabinet 3.3 Open-box Procedures Follow the steps below to open the box: 1.  Open the cover board. 2.  Remove the foam boards. 3.  Take the micro-BTS out directly. See Fig. 3.3-1.
 Chapter 3  Open-box Inspection  3-3CDMA micro-BTSZTE CORPORATIONZTE Plaza, Keji Road South, Hi-Tech IndustrialPark, Nanshan District, Shenzhe n, P.R.ChinaPostcode: 518057Tel: (+86755) 6790000Customer Support Center: 8008301118Goods:Net Weight:            (Kg)Volume:  81x52x40  (cm)Qty.:Packing List:Micro-BTSAccessories Fig. 3.3-1  Schematic Diagram for Opening a Box
  4-14 Installation of Cabinet  Summary     Describing the procedures to install the micro-BTS/remote station cabinet    Describing the possible installation modes 4.1 Installation Flow  Note The cabinets of ZXCBTS micro-BTS/remote stations are the same in structure, so is the installation method.   The cabinet can be installed in two modes: on pole or on wall. The installation flow is shown in Fig. 4.1-1.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    4-2Install the sup p ortInstallation on poleInstallation checkInstall the sunshade coverInstall the cabinetIndoorsInstall the sup p ortOutdoorsEndInstallation on wall Fig. 4.1-1    Flow of Installing the Cabinet 4.2 Installation Modes  Note The cabinets of ZXCBTS micro-BTS/remote stations are the same in structure, so is the installation method. As shown in Fig. 4.1-1, the cabinet can be installed either on pole or on wall based on the actual environment. 4.2.1 Installing Cabinet on Pole 1.  Disassemble the support from the cabinet. 2.  Secure the support onto the pole with fixing plates and 260mm-long bolts. The diameter of the pole should be between 60mm and 90mm. 75mm is recommended. See Fig. 4.2-1. If the equipment is to be installed outdoors, face the front side southward and the back side northward (This rule is applicable to the case that the equipment is
 Chapter 4  Installation of Cabinet  4-3installed in the Northern Hemisphere. If it is installed in the Southern Hemisphere, the opposite rule should be applied). 3.  Install the sunshade cover onto the support with four M4 bolts. See Fig. 4.2-4. 4.  Hold the cabinet to hang it onto the support, then push it into the shelf. See Fig. 4.2-2. 5.  Align the bolt holes on the support with those on the cabinet, and then screw down four M8 hexagon bolts. See Fig. 4.2-3. 6.  On the cabinet base there are hangers for rope. If necessary, use the rope to hang the cabinet onto the pole. See Fig. 4.2-1 for the schematic diagram of cabinet fastened on pole. Flat washerBoltM12 nut,spring washer,flat washerSupportPoleFixing plate Fig. 4.2-1  Schematic Diagram of Fastening the Cabinet onto the Pole (step 1)
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    4-4  Fig. 4.2-2  Schematic Diagram of Fastening the Cabinet onto the Pole (step 2)  Fig. 4.2-3  Schematic Diagram of Fastening the Cabinet onto the Pole (step 3)
 Chapter 4  Installation of Cabinet  4-5          Fig. 4.2-4    Schematic Diagram of the Cabinet Fastened onto the Pole  Caution For your safety, be sure to wear the safety belt when working at heights and the safety helmet when working at grounds. It is prohibited to work in thunder storm weather.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    4-64.2.2 Installing Cabinet on Wall 1.  Disassemble the support from the cabinet. 2.  Mark four points on the wall based on the four holes on the support, and then drill four holes with a percussive drill (using M12 drill bit). Secure the support onto the wall with four M10 expansion bolts. See Fig. 4.2-5. 3.  Hold the cabinet to hang it onto the support, and then push it into the shelf. 4.  Align the bolt holes on the support with those on the cabinet, and then screw down four M8 hexagon bolts. 5.  Install the sunshade cover if the equipment is to be installed outdoors. See Fig. 4.2-6 for the schematic diagram of installing cabinet on wall. WallSupportExpansion boltHexagon nutWasher Fig. 4.2-5    Schematic Diagram of Installing the Support onto the Wall
 Chapter 4  Installation of Cabinet  4-7        Fig. 4.2-6    Schematic Diagram of Installing the Cabinet onto the Wall  Note The modules and cables in micro-BTS (including ultra-wide coverage micro-BTS) and remote stations have been installed, connected and tested before delivery. Before commissioning, you only need to check if they are loose due to conveyance. Refer to Chapter 7 for the connection of cables between cabinets. According to the configuration requirement, you might need to add optical fiber modules or CSM5000 expansion modules in the expansion slots of the corresponding BDM board. If any fault occurs, the maintenance personnel can refer to this manual for simple maintenance.
  5-15 Installation of Power Supply System  Summary      Describing the methods for installing the power supply system..    Describing the procedures to install the power supply system.. 5.1 Introduction to Power Cables The micro-BTS/remote stations are supplied by 120V AC power or -48V DC power. AC micro-BTS are supplied by 120V AC power, and DC micro-BTS are supplied by -48V DC power.   5.1.1 -48V DC Power Cable The ZTE -48V DC ZXCBTS equipment is equipped with a piece of 10m-long cable, which can meet the installation requirement in most cases. If you need to assemble the cable on site in special cases, follow the instructions in this section. The DC power cable connector is a four-pin connector, and the power cable adopts four-core cable, as shown in Fig. 5.1-1. The corresponding relationship between the core wires and the binding posts are listed in Table 5.1-1.  Fig. 5.1-1    Four-pin Connector and Four-core Power Cable
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    5-2Table 5.1-1  Corresponding Relationship between Core Wires and Binding Posts Binding Post No.  Color of Core Wire  Power Polarity 1 Blue -48V 2 Red -48V 3 Black -48VGND 4 Olivine -48VGND 5.1.2 120V AC Power Cable The ZTE 120V AC ZXCBTS equipment is equipped with a piece of 10m-long cable, which can meet the installation requirement in most cases. If you need to assemble the cable connector on site in special cases, follow the instructions in this section. The AC power cable connector is a three-pin connector, and the power cable adopts three-core cable. Refer to Table 5.1-2 for the corresponding relationship between the core wires and the binding posts. Table 5.1-2  Corresponding Relationship between Core Wires and Binding Posts Binding Post No.  Color of Core Wire  Power Polarity 1  Yellow and green  PE 2 Brown L 3 Blue N 5.2 Connection of Power Cables 120V AC power supply and -48V DC power supply are used for the micro-BTS and remote stations. A waterproof connector is used to connect the power to the POWER terminal at the bottom of a cabinet, as shown in Fig. 5.2-1. 1.  Select a suitable type of power cable. If the cabinet is installed outdoors, outdoor shielded power cables should be used for power supply, which can withstand the influences of ultraviolet lights, rains and temperature changes. If common three-core AC power cables are used in special cases, PVC pipes should be added for protection. If the cabinet is installed indoors, common three-core power cables can be used for power supply.
 Chapter 5  Installation of Power Supply System  5-32.  Power cables should be laid in order. If they are laid in parallel with T1 signal cables, an interval of 200mm is required between them. 3.  Upon bundling of power cables, the space between two cable ties should be less than 0.5m to prevent friction with the tower upon swing of cables and avoid damage of power cable sheath.  Fig. 5.2-1    Connection of Power Cables and Grounding Cables at the Bottom of a Cabinet 5.3 Assembling Power Cable Connector 5.3.1 Assembling -48V DC Power Cable Connector Step 1: Put the connector components 1, 2, 3, 4 and 5 onto the cable, as shown in Fig. 5.3-1. 12354 Fig. 5.3-1    Assembling a Power Cable Connector (step 1) The power cable with around connector forconnecting the POWERterminal at the bottomof the cabinet PGND terminalof the cabinet
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    5-4Step 2: Strip the 17mm-long sheath off the four-core cable at the end to be welded. If the sheath of more than 17mm is stripped, the component 3 cannot press the cable tight; if less than 17mm, inconvenience might be caused for installation. See Fig. 5.3-2. 12354 Fig. 5.3-2    Assembling a Power Cable Connector (step 2) Step 3: Strip the 5mm-long insulation layer off the four core wires respectively, twist up the copper core wires and brush a slice layer of soldering tin on them, and then put a 10~15mm-long heat-shrink tube onto each core wire. Step 4: Joint the core wires respectively with the binding posts of the component 6 by welding them, push the heat-shrink tubes to the proper position and then make them shrink, as shown in Fig. 5.3-3. Refer to Table 5.1-1 for the corresponding relationship between the core wires and the binding posts. 123546 Fig. 5.3-3    Assembling a Power Cable Connector (step 4)
 Chapter 5  Installation of Power Supply System  5-5Step 5: Screw to connect the component 5 with the component 6, as shown in Fig. 5.3-4. 123546 Fig. 5.3-4    Assembling a Power Cable Connector (step 5) Step 6: Push the components 2, 3 and 4 into the component 5, and then screw down the component 1 onto the component 5. Be sure to screw the component 1 but not 5. See Fig. 5.3-5. 156 Fig. 5.3-5    Assembling a Power Cable Connector (step 6) 5.3.2 Assembling 120V AC Power Cable Connector The steps for assembling an AC power cable connector are the same as that for assembling a DC power cable connector. The only difference is that the three-pin connector and three-core power cable are used for AC power cables. Refer to the preceding contents for the procedures and Table 5.3-1 for the corresponding relationship between the core wires and the binding posts.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    5-6Table 5.3-1  Corresponding Relationship between Core Wires and Binding Posts Binding Post No.  Color of Core Wire  Power Polarity 1  Yellow and green  PE 2 Brown L 3 Blue N
  6-16 Installation of Grounding System  Summary      Describing the method for installing the grounding system 6.1 Introduction to the Grounding System This section details the procedures to install the grounding system, including grounding copper busbar and feeder cable grounding kit. Grounding aims to protecting both the human being and the equipment against lightning shock and electromagnetic interference. The grounding system is composed of indoor groundings, outdoor groundings and underground grounding net. The grounding system of a ultra-wide coverage micro-BTS includes protection grounding on the chassis, lightning arrester for RF components in the cabinet, for GPS antenna, for T1 cables, for 120V AC power and for feeder cable grounding kit. The customer needs to complete the construction of the basic grounding net and the grounding system of the tower and other buildings, and offer the points for connecting the indoor and outdoor grounding busbars to the grounding net through different 50mm2 wires. The conductor led from the PGND terminal of the shelf is connected to the grounding copper busbar, and the conductor led from the -48VGND of the shelf is connected to the DC power copper busbar. Each feeder cable should be connected to the outdoor grounding copper busbar through the cable grounding kit before being led into the equipment room. See Fig. 6.1-1.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    6-2Feeder cable grounding kitTower platformUFeeder cable Grounding cable (35mm2)Micro-BTSDC power rackOther devicesOutdoorgroundingbusbarIndoorgroundingbusbarPGNDs of all devices in theequipment room (including thecabling rack) are connected tothe indoor grounding busbarGrounding cable (50mm2) Fig. 6.1-1  Schematic Diagram of Grounding Connections 6.2 Installing Grounding System 6.2.1 Installing Outdoor Grounding Copper Busbar The outdoor grounding copper busbar functions in lightning protection. It is usually installed on the wall outside the equipment room, and the best position is right under the feeder cable window or on the rain-proof wall of the feeder cable well on the top of a building.
 Chapter 6  Installation of Grounding System  6-3In actual installation, first determine the position for the copper busbar based on the engineering design drawing, and then install the busbar on the wall with expansion bolts. See Fig. 6.2-1 for the appearance of the grounding copper busbar.  Fig. 6.2-1    Appearance of a Grounding Copper Busbar 6.2.2 Installing the Grounding System of Micro-BTS The cabinets of ultra-wide coverage micro-BTS/remote stations are equipped with PGND terminals, as shown in Fig. 6.2-2. The PGND terminal is connected to the indoor grounding copper busbar via the 16mm2 yellow or olivine conducting wire. If the equipment is installed outdoors, the PGND terminal is connected with the grounding cable from the tower or from the top of the building in the crimping connection mode.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    6-4PGNDterminal ofthe cabinet Fig. 6.2-2    Connection of Power Cable and PGND Cable at the Bottom of a Cabinet 6.2.3 Installing Feeder Cable Grounding Kit  Caution: It is prohibited to install the grounding kit in thunderstorm weather; otherwise, the installation personnel might be hurt. When installing the grounding kit, be sure to keep the feeder cable at the joint straight. 6.2.3.1 Grounding Principles of Primary Feeder Cable 1.  Generally, each primary feeder cable should be grounded at least three times for lightning protection, that is, on the tower platform, between the tower and the outdoor cabling rack, and on the wall before the feeder cable is led into the equipment room. If the primary feeder cable is more than 60 meters long, a lightning grounding kit should be installed every 20 meters. 2.  The antenna feeder system, antenna mount and newly-installed cabling rack should all be welded to the lightning protection net of the building. The feeder cable should also be grounded at three points, that is, on the antenna pole, on the rooftop, and on the wall before the feeder cable is led into the equipment room. 3.  Before leading the primary feeder cable along the outdoor cabling ladder from the top of the building to the equipment room, check whether the cabling ladder is grounded. If not, request the network operator to accomplish it as soon as possible.
 Chapter 6  Installation of Grounding System  6-56.2.3.2 Procedures to Install a Grounding Kit 1.  Prepare such tools as paper knife, straight screwdriver, spanner and sharp nose pliers. 2.  Choose a suitable position for installing the grounding kit, and cut the sheath off the 7/8" feeder cable based on the size of the grounding kit. The structure of a grounding kit is shown in Fig. 6.2-3. Grounding terminal Grounding cableFeeder cableGrounding wire clipOut-layer coppercore of feeder cableSheet copper offeeder cable Fig. 6.2-3    Structure of a Grounding Kit 3.  Lead the grounding cable of the lightning grounding kit to the grounding net. Keep the angle between the grounding cable and the primary feeder cable no more than 15°. If the antenna feeder system is installed on a tower, lead the grounding cable downward along the tower. If the antenna feeder system is installed on the top of a building, lead the grounding cable to the lightning protection net. 4.  Before installing the grounding kit, wrap the waterproof adhesive tape around the grounding cable near the grounding copper for sealing, as shown in Fig. 6.2-4.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    6-6 Fig. 6.2-4  Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable 5.  Clamp the external conductor with the grounding copper and clip tightly. 6.  Seal the joint between the grounding kit and the feeder cable as follows:   First wrap the waterproof adhesive tape and then the PVC tape around the joint.   Wrap the waterproof adhesive tape circularly from bottom upward, and then from top downward, finally from bottom upward again. Note that the next circle covers 1/2 of the previous circle. 7.  Connect the grounding terminal of the grounding kit to the tower body or the cabling rack on the top of the building (the cabling rack is connected to the lightning protection net). Remove the paint and oxide at the junction within the radius of 13mm and then coat the clean area with antioxidant cream. After the connection, paint the area with antirust paint. 8.  Before the primary feeder cable is led into the equipment room, connect the grounding terminal of the grounding kit to the outdoor grounding busbar.
  7-17 Connection of Cables  Summary      Describing the connection of internal cables.    Describing the connection of external cables. 7.1 Checking Internal Cable Connections 7.1.1 Type and Configuration of Internal Cables There are 422 or 485 internal cables totally. Refer to Table 7.1-1 for the types and configurations of internal cables in micro-BTS/remote stations. Table 7.1-1    List of Types and Configurations of Internal Cables Type Name  Applied Equipment RF21  Single-carrier 800M micro-BTS/remote stations RF22  Single-carrier and double-carrier 800M micro-BTS/remote stationsRF23  Single-carrier and double-carrier 800M micro-BTS/remote stationsRF24  Single-carrier and double-carrier 800M micro-BTS/remote stationsRF25  All micro-BTS/remote stations RF26  Single-carrier and double-carrier 800M micro-BTS/remote stationsRF27  Single-carrier and double-carrier 800M micro-BTS/remote stationsRF28  Single-carrier and double-carrier 800M micro-BTS/remote stationsRF32  Single-carrier 1.9G micro-BTS/remote stations RF33  Single-carrier and double-carrier 1.9G micro-BTS/remote stations RF34  Single-carrier and double-carrier 1.9G micro-BTS/remote stations RF35  Single-carrier 1.9G micro-BTS/remote stations RF36  Single-carrier and double-carrier 1.9G micro-BTS/remote stations RF37  Single-carrier 1.9G micro-BTS/remote stations RF38  Single-carrier and double-carrier 1.9G micro-BTS/remote stations RF cables RF42  All double-carrier micro-BTS/remote stations
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    7-2Type Name  Applied Equipment   RF43  All double-carrier micro-BTS/remote stations RF29  All single-carrier and double-carrier micro-BTS RF30  Single-carrier and double-carrier 800M micro-BTS RF31  Single-carrier and double-carrier 800M micro-BTS RF39  Single-carrier and double-carrier 1.9G micro-BTS RF40  All single-carrier and double-carrier remote stations RF41  All single-carrier and double-carrier remote stations Clock cables BDM-GPS  All single-carrier and double-carrier micro-BTS MPA CONTL  All micro-BTS/remote stations Communication cables RXTDX  All micro-BTS/remote stations DCDX01  All micro-BTS/remote stations DCDX02  All micro-BTS/remote stations DCDX03  All micro-BTS/remote stations ACDX01  All AC-powered micro-BTS/remote stations ACDX02  All AC-powered micro-BTS/remote stations ACDX03  All micro-BTS/remote stations configured with heater ACDX04  All AC-powered micro-BTS/remote stations F-DC PWR-001  All DC-powered micro-BTS/remote stations F-DC PWR-002  All DC-powered micro-BTS/remote stations Power cables F-DC PWR-003  All DC-powered micro-BTS/remote stations F-FAN-004 All single-carrier and double-carrier micro-BTS F-FAN-005 Single-carrier and double-carrier 20W micro-BTS/remote stations Fan cables F-FAN-006 Single-carrier and double-carrier 20W micro-BTS/remote stations DX01  All micro-BTS/remote stations DX02  All micro-BTS/remote stations Grounding cables DX03  All micro-BTS/remote stations MONDX01 All micro-BTS/remote stations MONDX02 All micro-BTS/remote stations DX04  All single-carrier and double-carrier micro-BTS DX05  All single-carrier and double-carrier remote stations Alarm cables DX06  All micro-BTS/remote stations Among these cables, only ACDX04 (AC power cable) and F-DC PWR-002 (DC power cable) are delivered with the equipment, and other cables have been connected in the equipment before delivery.
 Chapter 7  Connection of Cables  7-37.1.2 Connection of Internal Cables Refer to Appendix B for the connection of internal cables. 7.2 Connecting External Cables 7.2.1 Connecting Optical Fiber  Note The optical fiber connectors of micro-BTS/remote stations are SC connectors. The ODF or optical connection box provided is equipped with FC connectors by default. If there are special requirements on the connectors, contact ZTE for customization.  7.2.1.1 Selecting Optical Fiber Different optical fibers are used for the connections between macro-/micro-BTS and remote stations. 1.  If a remote station is near to a relative micro-BTS, optical fiber is used directly. The optical fiber adopts waterproof pigtail cable, and both ends are equipped with waterproof blockers and SC connectors. See Fig. 7.2-1 for the structure of the optical fiber. SC/P C c o n n ec t o rOptical fiber corewire (0.7m)Optical fiber corewire (0.7m)WaterproofblockerSingle-mode waterproofpigtail cable Fig. 7.2-1    Structure of Optical Fiber (1)
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    7-4The core wires at both ends are 0.7m long. Both ends of the optical fiber can connect either a micro-BTS or a remote station. You can choose 10m/20m/50m/100m-long optical fiber for this connection based on the actual situation. 2.  If an outdoor remote station is near to a relative indoor macro-BTS, optical fiber is used for connecting them directly. The optical fiber adopts waterproof pigtail cable, with both ends being SC connectors. In addition, one end is equipped with a waterproof blocker. See Fig. 7.2-2 for the structure of the optical fiber. Optical fiber corewire (3m)SC/PCconnectorOptical fiber corewire (0.7m)Waterproof blockerSingle-mode waterproofpigtail cable Fig. 7.2-2    Structure of Optical Fiber (2) The core wires of the end equipped with a waterproof blocker are 0.7m long, and those of the other end are 3m long. The end with a waterproof blocker is to be connected with the remote station, and other end is used to connect the macro-BTS. You can choose 50m/100m-long optical fiber for this connection based on the actual situation.   3.  If a remote station is far from a relative macro-BTS and an ODF or optical connection box is required, two pieces of optical fiber should be used for connecting the macro-BTS with the ODF and the ODF with the remote station respectively.
 Chapter 7  Connection of Cables  7-51)  Connection between the macro-BTS and the ODF The indoor-type optical fiber is adopted, with one end being SC/PC connectors and the other end being FC/PC connectors. See Fig. 7.2-3 for the structure of the optical fiber. FC/PC connectorSC/PC connectorSingle-modeoptical fiber Fig. 7.2-3    Structure of Optical Fiber (3) The SC/PC connectors are used to connect the macro-BTS, and the FC/PC connectors are used to connect the ODF. There is only one option for this connection: 30m-long optical fiber. 2)  Connection between the ODF and the remote station The optical fiber adopts waterproof pigtail cable. The end equipped with a waterproof blocker uses SC/PC connectors, and the other end offers FC/PC connectors. See Fig. 7.2-4 for the structure of the optical fiber. SC/PC connector FC/PC connectorOptical fiber core wire(3m)Optical fiber core wire(0.7m)WaterproofblockerSingle-mode waterproofpigtail cable Fig. 7.2-4    Structure of Optical Fiber (4)
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    7-6The core wires of the end equipped with a waterproof blocker are 0.7m long, and those of the other end are 3m long. The end with a waterproof blocker is to be connected with the remote station, and the other end is to be connected with the ODF. You can choose 50m/100m-long optical fiber for this connection based on the actual situation. Caution: If the ODF uses cubical connectors, contact ZTE in advance. 7.2.1.2 Laying Optical Fiber 1.  Connecting optical fiber for a micro-BTS/remote station Because the end of the optical fiber for connecting a micro-BTS/remote station is equipped with a waterproof blocker, you need to remove the cover of the optical interface at the bottom of a micro-BTS/remote station first, insert the pigtail fiber into the cabinet, and then screw down the waterproof blocker into the optical interface, as shown in Fig. 7.2-5. WaterproofblockerOpticalfiber Fig. 7.2-5  Schematic Diagram of Connecting Optical Fiber 2.  Connecting optical fiber for a macro-BTS If the optical fiber is used to connect the Local Fiber Module (LFM) of a macro-BTS, first insert the optical fiber into an interface on the front panel of
 Chapter 7  Connection of Cables  7-7the LFM, lay the optical fiber along the horizontal cabling trough on the top of the TRX layer, and then along the vertical cabling trough on the left of the shelf; next, open the cover of the standby interface marked with “BTM ANT” on the top of the macro-BTS, pull the optical fiber out of the shelf and then lay it onto the cabling rack on top. 3.  Requirements for laying optical fiber The optical fiber should be arranged in order, with the interval for cable ties less than 0.5m. The minimum bending radius of the outdoor-type optical fiber is 90mm, and that of the indoor-type optical fiber is 30mm.   7.2.2 Connecting Multi-carrier Interconnection RF Cables If a double-carrier & single-sector micro-BTS/remote station is required, two cabinets need be configured. These two cabinets should be connected by cables to achieve transmission of diversity antenna signals. When a micro-BTS cabinet and a remote station cabinet form a double-carrier & single-sector micro-BTS system, two pieces of RF cables need be added to cross-connect the RFE-ANT0 interface with the EXTEND interface at the bottom of the two cabinets respectively. Similarly, when two double-carrier remote station cabinets form a double-carrier remote station and it is used in cooperation with a double-carrier macro-BTS, two pieces of RF cables need be added to cross-connect the RFE-ANT0 interface with the EXTEND interface at the bottom of the two cabinets respectively. Refer to Appendix B for the configuration of internal cables in a double-carrier system. The interconnection RF cable is 3m long, with both ends being RF N connectors. It is a finished product delivered with cabinets. It is named as “F-RF05-009”. See Fig. 7.2-6 for the cable connections between two cabinets.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    7-8 Fig. 7.2-6    Connection of Interconnection RF Cables 7.2.3 Waterproof Processing of Joints In case of double-carrier configuration, the joints between the sockets at the bottom of the cabinets and the connectors of the interconnection RF cables should be wrapped with waterproof adhesive tape. In addition, the joint between the socket at the bottom of a 20W micro-BTS (M802T micro-BTS) cabinet and the connector of the external fan cable should also be wrapped with the adhesive tape. You need to do the following: 1.  Secure the relative connectors and sockets. 2.  Implement waterproof processing to the joints. 1) Wrap the joints with the waterproof adhesive tape from the top of the connectors. The first layer should be wrapped in the same direction as for fastening the cable connectors. 2) Stretch the tape with force and wrap it circularly for three layers totally. Note that the next circle covers 1/2 of the previous circle, and the wrap stops at the position about 10cm away from the joint. 3)  Grip the joint with force to make the tape stuck firmly with the joint. RFE-ANT0  RFE-ANT0 EXTEND  EXTENDMicro-BTS/remote station Remote station Interconnection RF cable (3m)
 Chapter 7  Connection of Cables  7-94) Wrap two layers of PVC tape around the waterproof adhesive tape in the same way as for wrapping the waterproof adhesive tape. 5)  Finally wrap a layer of anti-ultraviolet tape. 7.2.4 Connection of Trunk Cables There are T1 interfaces at the bottom of the primary cabinet of a micro-BTS for connecting T1 cables (100-ohm coaxial cables), as shown in Fig. 7.2-7.   Fig. 7.2-7    Connection of T1 Cables 1. Select T1 cables. Micro-BTS can be installed outdoors, so PE-sheath T1 cables are used generally. If common T1 cables are used in an outdoor micro-BTS, PVC pipe should be added for protection. 2.  Lay the T1 cables in order. Keep T1 cables and AC power cables separate with distance of more than 200mm. 3.  When laying T1 cables on a tower, the space between two cable ties should be less than 0.5m to prevent friction with the tower upon swing of cables and avoid damage of T1 cable sheath.  T1 cable
  8-18 Installation of Primary Antenna Feeder System  Summary      Describing the composition of the primary antenna feeder system.    Describing the procedures to install the primary antenna feeder system. 8.1 Preparations Before installing the primary antenna feeder system, check the qualification of the installation personnel for working at heights, installation environment, security measures, installation tools and system components, for the purpose of ensuring the successful installation. 8.1.1 Installation Personnel The antenna feeder system is installed by the professional installation personnel under the monitoring of the installation supervisor. The installation supervisor should be familiar with the materials, tools and operations for the installation, who is responsible for assigning suitable work for the installation personnel and recording the actual engineering data. The installation personnel should be skillful and healthy. Those who work at heights should have obtained the corresponding qualification, have no acrophobia, observe the security regulations, and have purchased the personal accident insurance. In addition, they are prohibited from drinking alcohol when working.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-28.1.2 Installation Environment Check if the outdoor lightning grounding cable is well grounded and if its cross-section area is more than 50mm2. Check if the distance between the antenna pole and the lightning rod/lightning grounding point/outdoor cabling rack, the firmness and wind-resistant ability of the pole meet the design requirements. In addition, check if the necessary tools and assisting materials are prepared, and if the route for laying the primary feeder cables is determined through negotiation. The equipment provider presents the requirements on the installation of the antenna mount based on the structure and size of the antenna, and the network operator should install the antenna mount as required. The network operator is also responsible for the installation of the outdoor cabling rack, lightning rod, lightning grounding point and outdoor lightning grounding cable. Moreover, the network operator needs to drill holes on wall or rooftop for installing the feeder cable window as one of the equipment room conditions. 8.1.3 Security Measures  Caution The installation personnel working at heights must wear the safety belt, and those working on ground must wear the safety helmet. They must wear working clothes and shoes causing no slips when climbing up the tower. 1.  Safety precautions should be stressed to the installation personnel. 2.  The outdoor installation should be conducted in sunny days without strong wind. 3.  Obvious signs should be set in the installation site to notify irrelative people to keep away from the site. The installation personnel working on ground are obligate to keep irrelative people, esp. children away from the site. The tools used on the tower and some metal components might slip to cause casualties, so they must be put in a canvas tool bag when not used, and the bag must be sealed immediately after you open it for a tool or component. 8.1.4 Installation Tools 1.  Measurement tools: A compass, multimeter, inclinometer and tape measure; 2.  Communication tools: Two mobile phones;
 Chapter 8  Installation of Primary Antenna Feeder System  8-33.  Raising tools: Pulley block and rope;   4.  Special tools: Cutter for cutting primary feeder cables and tools for assembling connectors; 5.  General tools: Adjustable wrench, sharp nose pliers, diagonal pliers, electrical knife, file and hacksaw; 6.  Protection tools: Safety belt, safety helmet, safety rope, thick working clothes, RF prevention clothes, canvas tool bag, gloves, and multi-purpose sockets; 7.  Other tools: Herringbone ladder and the wooden wheel axis for uplifting the primary feeder cable (which can be borrowed locally). 8.2 Composition and Installation Requirements of Antenna Feeder System 8.2.1 Composition The antenna feeder system is composed of antennae, antenna jumper cables, primary feeder cables, lightning arrester, jumper cables on top and grounding parts, as shown in Fig. 8.2-1.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-4Lightning rodAntenna (2 sets)Jumper cable (1/2", 2 pieces)Lightning grounding kitPrimary feeder cable (7/8", 2 pieces)Jumper cable(1/2", 2 pieces)Lightning grounding kitLightninggrounding kitLightning arresterEquipment roomTowerMicro-BTSCabling rack Fig. 8.2-1    Typical Structure of the Antenna Feeder System
 Chapter 8  Installation of Primary Antenna Feeder System  8-58.2.2 Technical Parameters 1.  Height of antenna It depends on the networking plan. 2.  Azimuth angle of antenna It depends on the networking plan. 3.  Pitch angle of antenna It depends on the networking plan. Generally, it is between 0° and 10° (adjustable). 4.  Pointing direction of antenna It depends on the azimuth angle of the antenna. Two antennae of the same sector must point to the same direction. 5.  Distance between two diversity antennae Two antennae of one sector are diversity reception antennae to each other. They have the same height, but they should be distanced as much as possible. If the following formula is met, the installation requirement is met. d ≥ 10λ~20λ (or H/d=11)d: Distance between two diversity antennae; H: Height from the antenna to the ground. If the carrier is 1.9GHz, the diversity distance should be more than 1.5m. If the carrier is 800MHz, the diversity distance should be more than 3.5m. 8.3 Installation Flow The antenna installation flow is as shown in Fig. 8.3-1.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-6St a r tDirectionalantennaAssemblecomponents of adirectional antennaFasten the antennaEndRaise/carry theantennaDetermine theinstallation positionOmniantennaAdjust the directionand pitch angle of thedirectional antennaSecure the omniantennaKeep the omniantenna verticalSe cur e  t h edirectional antennaRaise/carry theantennaConnect the antennawith the jumper cableand then seal their jointConnect the antennawith the jumper cableand then seal their jointTypes ofAntenna Fig. 8.3-1    Antenna Installation Flow 8.4 Installation of Antenna  Caution: 1. Be cautious during the installation to prevent personal injury or equipment damage. 2. Measures should be taken to protect human body against the radiation when adjusting the antenna, for example, the installation personnel should wear the anti-radiation clothes. 8.4.1 Determining Installation Location The location for installing the antenna should be determined based on the engineering design drawing. If the actual location of the antenna mount is different from the engineering design, the installation engineers, customer representative and design unit should negotiate to complete the second design according to the requirements of the
 Chapter 8  Installation of Primary Antenna Feeder System  8-7BTS on network coverage, space diversity, azimuth angle and pitch angle, thus ensuring desirable network coverage in future. 8.4.2 Installing Accessories of Directional Antenna Some fasteners need be installed on a directional antenna first. For example, the KATHREIN antenna need be installed with the fasteners “738516” and “737974”. Before fastening the antenna, first install the fastener “737974” with angle adjustment setting onto the top and bottom of the antenna (as shown in Fig. 8.4-1), and then connect the fastener “737974” and the pole fastener “738516” with short bolts. During the installation, spring washers and flat washers are used. Please refer to the guide book delivered with the equipment for the information of specific fasteners to be used. Assemble the fasteners and angle adjustment accessories onto the antenna in advance before installing the antenna on the tower. φ75mm738 51 6737 9740o~16o65o737 974Antenna poleConnect them with two short bolts and nutsConnect the antenna and the fastener withshort bolts (spring washers and flatwashers are added,  and nuts are equippedwith waterproof washers)After the connection,  move thetop of the antenna up and downto adjust the pitch angleScale KAT HR EINDirectionalantennaAfter the connection,  move theantenna right or left to adjust theazimuth angle Fig. 8.4-1    Installation of the KATHREIN Antenna
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-88.4.3 Transporting and Raising Antenna  Caution: Both the installation personnel working on tower and those working under tower should cooperate to raise the antenna onto the tower with rope. Note to keep the antenna away from the tower body to prevent any damage to the antenna when pulling it up the tower. Use rope and pulley block to raise the antenna, 3-m antenna jumper cable and other accessories (including tools, safety belt, adhesive tapes and cable ties) up to the tower platform, and then put them in a safe place to avoid falling. Note that the fasteners and other metal tools must be put in a canvas tool bag before pulling them up. When raising a directional antenna or an omni antenna, tie a knot at each end of the antenna to facilitate the cooperation between the installation personnel on and under the tower, as shown in Fig. 8.4-2. If an antenna is to be installed on the top of a building, carry the antenna and other accessories to the installation site manually. Pulley blockRope forraising theantennaTie a knot with rope ateach end of the antennaPull the antenna away from theantenna to avoid damaging theantenna Fig. 8.4-2    Schematic Diagram of Raising the Antenna to the Tower Top
 Chapter 8  Installation of Primary Antenna Feeder System  8-98.4.4 Installing and Adjusting Directional Antenna  Note: The antennae of different providers require different installation modes. This section takes the installation of the KATHREIN antenna as an example. Before the installation, read the installation manual delivered with the antenna carefully. Install a directional antenna by the following steps: 1.  Fastening the directional antenna onto the pole Fasten the fastener of the directional antenna with the pole. Do not screw the screws too tight or too loosely. If they are too loose, the antenna might fall off; if they are too tight, it is inconvenient to adjust the azimuth angle and pitch angle of the antenna later. 2.  Adjusting the azimuth angle of the antenna 1) Measure the azimuth angle of the antenna with a compass. Then check the engineering design drawing for the antenna direction. 2) Adjust the orientation of the antenna by twisting it slightly, as shown in Fig. 8.4-1. At the same time, measure the orientation of the antenna with the compass. Keep adjusting until the deviation is within the design requirement, that is, less than or equal to 5° generally. 3)  After the adjustment, fasten the fastener 738516 tight. 3.  Adjusting the pitch angle of the antenna 1) Adjust the bubble inclinometer to the angle as required in the engineering design. 2)  Adjust the pitch angle of the antenna slightly until the bubble of the inclinometer is located in the middle when you measure the pitch angle with it, as shown in Fig. 8.4-3. 3)  After the adjustment, fasten the fastener 737974 tight.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-10 Fig. 8.4-3    Schematic Diagram of Adjusting the Pitch Angle of the Antenna 8.4.5 Installing and Adjusting Omni Antenna Install an omni antenna by the following steps: 1.  Fasten the antenna (the part with jacket) onto the antenna mount with two fixing clips. Do not fasten it too tight or too loosely. If too tight, the jacket might be damaged; if too loosely, the requirements on weight-bearing and wind-resistant abilities cannot be met. 2.  Check if the antenna is vertical. If so, fasten the antenna with the pole tight. 3.  Protrude the antenna mount installed with the antenna out of the tower platform. Adjust the mount to make the antenna vertical. 8.4.6 Connecting Jumper Cable with Antenna and Sealing Their Joint  Note: You can connect the jumper cable with the antenna and seal their joint before installing the antenna onto the pole, which can shorten the time for working at heights and reinforce the connection and waterproof performance of the joint. The operations are as follows: 1.  Insert the jumper cable connector into the antenna interface and then screw them tight.
 Chapter 8  Installation of Primary Antenna Feeder System  8-112.  Implement waterproof processing to the joint between the antenna and jumper cable. 1)  Wrap the joint with the waterproof adhesive tape from top download. The first layer should be wrapped in the same direction as for fastening the antenna jumper cable. 2)  Wrap the waterproof tape circularly for three layers totally. Note that the next circle covers half of the previous circle, and the wrap stops at the position 10cm away from the joint. 3)  Grip the joint with force to make the tape stuck firmly with the joint. 4)  Wrap two layers of PVC tape around the waterproof adhesive tape in the same way as for wrapping the waterproof adhesive tape. 5)  Finally wrap a layer of anti-ultraviolet tape. 8.5 Installation of Feeder Cable Window  Note: The size of the feeder cable window provided by ZTE is 400mm×400mm. It is a four-hole window and 12 pieces of feeder cables can pass through it. A 300mm×300mm hole should be drilled on the wall for the installation of this feeder cable window. If a special feeder cable window is used, a hole should be drilled based on the actual size of it. No feeder cable window is needed when a micro-BTS is installed outdoors. The feeder cable window is usually installed on the outside wall of the equipment room, right between the indoor and outdoor cabling racks. If the primary feeder cable window is installed on the rooftop, you need to take measures to make it waterproof. For example, you can seal it with asphaltum or glass cement. The feeder cable window has four holes and can be connected with 12 pieces of feeder cables at most, as shown in Fig. 8.5-1. Follow the steps below to install a feeder cable window:  1.  Determine the installation location based on the engineering design drawing. 2.  Drill a hole on the wall according to the size of the feeder cable window used.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-123.  Drill holes for installing expansion bolts with a percussive drill, and then secure the main board of the feeder cable window with the expansion bolts. 4.  Install the sealing pad and gasket when leading the primary feeder cables into the equipment room. 5.  In cold and sandy places, install a wooden board in the equipment room to block sand blown by the wind and preserve heat.  Fig. 8.5-1    Structure of a Feeder Cable Window 8.6 Connection of Feeder Cable This section describes how to assemble the 7/8” feeder cable connectors, how to connect the jumper cable & the primary feeder cable/antenna and seal their joint, and how to lay and fasten the feeder cables. The complete structure of a feeder cable of a micro-BTS/remote station is shown in Fig. 8.6-1. If a micro-BTS is installed outdoors and it is near to the antenna, the 1/2” feeder cable can be used for the primary feeder cable.
 Chapter 8  Installation of Primary Antenna Feeder System  8-13LabelAntenna jumper cableCustomized jumpercable on topLabelFeeder cableMale N connector Fig. 8.6-1    Structure of the Feeder Cable of a Micro-BTS/Remote Station 8.6.1 Determining Route for Feeder Cable The cabling route of the feeder cables should be determined according to the engineering design drawing. If an alteration is necessary, negotiate with the customer representative for solution. Note that the primary feeder cables should be as short as possible. 8.6.2 Assembling Connectors of Primary Feeder Cable  Caution: Assembling feeder cable connectors is the most important procedure in the installation of the antenna feeder system, for the quality of them directly affects the performance of both equipment and network.   Be cautious when using the cutter, for it is very sharp. This section describes how to assemble connectors for the ROSENBERGER 7/8” feeder cable. For the assembly of connectors for other types of feeder cable or feeder cable of other manufacturers, refer to the specific installation manual.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-141.  The cutter used is shown in Fig. 8.6-2.  Fig. 8.6-2  Cutter for Assembling 7/8” Feeder Cable Connectors 2.  Pull the feeder cable straight (about 150mm long) at the end to be installed with a connector, and then strip 50mm-long sheath off the cable with the cutter. 3.  Put the feeder cable on the trough of the cutter EASIAX, reserve four corrugations at the end of the blade, and then press down the handle. The main blade should point to one wave crest. 4.  Screw to shut the cutter closely. In this way, the internal and external copper conductors of the feeder cable are severed, and at the same time the cable sheath is severed by the assisting blade, as shown in Fig. 8.6-3.  Fig. 8.6-3    Schematic Diagram of Cutting the Feeder Cable with the Cutter 5.  Check if the cutting position is correct, as shown in Fig. 8.6-4. Wave crest Fig. 8.6-4  Schematic Diagram of Correct Cutting Size
 Chapter 8  Installation of Primary Antenna Feeder System  8-156.  Disassemble the feeder cable connector into two parts: front part and back part. And then insert the feeder cable into the back part until it contacts the first corrugation of the cable. 7.  Insert the tube expander of the cutter into the feeder cable and then screw left and right to expand the external copper conductor, as shown in Fig. 8.6-5.  Fig. 8.6-5    Schematic Diagram of Expanding the External Copper Conductor 8.  Check if there are copper bits left in the conductor and if the conductor is expanded evenly. Pull the back part of the connector with force to check if it is connected firmly with the cable. If any requirement cannot be met, redo the above steps. 9.  Connect the front part with the back part, as shown in Fig. 8.6-6.  Fig. 8.6-6    Schematic Diagram of Connecting the Front Part with the Back Part of the Connector 10.  Clamp the front part of the connector with a wrench and use another wrench to clamp the back part. Twist the back part but keep the front part unmoved until they are connected firmly.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-16Twist this  wrench onlyKeep  this wrench immovable Fig. 8.6-7    Schematic Diagram of Fastening the Front Part with the Back Part of the Connector 8.6.3 Cutting Feeder Cable  Caution: Stick temporary labels at both ends of the primary feeder cables after cutting them. Labels can also be stuck in the middle part of the feeder cables but they must be the same; otherwise, wrong connections might be caused. On the installation site, measure the cabling route of the primary feeder cables accurately and then cut the cables as needed. The operations are as follows: 1.  When the antenna feeder system is to be installed on the top of a building: 1)  Measure the cabling route with a tape measure to determine the length of the primary feeder cables needed by each sector. 2)  Add some margin (1m~2m) to the measured lengths when cutting the cables. 3)  After cutting a piece of primary feeder cable, stick temporary labels at both ends of the cable, for example, ANT1, ANT2, ANT3, ANT4, ANT5, ANT6. 4)  Carry the feeder cables having been cut to the top of the building. Ensure that the cables are not squeezed or damaged during the conveyance. 2.  When the antenna feeder system is to be installed on a tower: 1)  Pull one end of the feeder cable to the tower top with the roller support, pulley block and rope. Then the installation personnel under the tower cut the cable based on the length needed (with a certain margin). Stick a temporary label at
 Chapter 8  Installation of Primary Antenna Feeder System  8-17the lower end of the cable. Stick a formal label after the cable is led into the equipment room. 2)  Assemble the connectors before raising the primly feeder cables, thus shortening the time for working at heights and ensuring the quality of the connectors. 8.6.4 Raising Primary Feeder Cable When the antenna feeder system is to be installed on a tower, the pulley block will be used to raise the primary feeder cables, as shown in Fig. 8.6-8. The operations are as follows: 1.  Check the labels at both ends of the primary feeder cable to ensure that it is the right cable. 2.  Wrap the feeder cable connector with a piece of flax cloth or an antistatic plastic bag filled with foam, and then bundle it tight. 3.  Tie a knot with the rope on the feeder cable at the place 0.4m away from the connector and then another knot about 3.4m away from the connector, for the purpose of facilitating the cooperation between the installation personnel on and under the tower to raise the cable and preventing the feeder cable and its connector from being damaged due to hit with the tower. 4.  After the primary feeder cable is pulled to the tower top, fasten it tight.  Caution: Raise the primary feeder cable with care to avoid damaging the sheath of it. If not, the whole piece of the cable will be wasted. Mind your own safety also when raising the cable.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-18Pulley blockThe rope forpulling the cableup the towerThe feeder cableconnector is wrappedTie a knot with the rope on the feeder cable at theplace 0.4m away from the connector and thenanother knot about 3.4m away from the connectorUse this rope to pull the feeder cable awayfrom the tower to prevent damaging the cableand the connector when raising the cableLabel Fig. 8.6-8  Schematic Diagram of Pulling the Feeder Cable Up the Tower 8.6.5 Laying and Fastening Primary Feeder Cable 1. Cabling principles 1)  The primary feeder cables should be laid in order on the cabling rack after being led into the equipment room through the feeder cable window. 2)  The primary feeder cables should be laid without crossings along the outdoor cabling rack and the cabling ladder of the tower. 3)  Be familiar with the cabling route of the primary feeder cables and draw it on paper in advance to ensure there are no crossings during the actual cabling.
 Chapter 8  Installation of Primary Antenna Feeder System  8-194)  The minimum bending radius of the primary feeder cable should be no less than 20 times of its semi-diameter. The minimum one-time bending radius is 90mm, and the minimum repeated bending radius is 200mm. 5)  The maximum interval between hangers is 1.65m. 2. Cabling procedures: 1)  In principle, a hanger should be installed on the tower or cabling rack every about 1.5m. For onsite installation, the interval can be lengthened or shortened depending on the actual situation, but the maximum interval cannot exceed 1.65m. Install the hangers with even distance in the same direction. If two rows of hangers are installed on one cabling ladder, keep them in parallel and in order. See Fig. 8.6-9 for the appearance of a hanger.  Fig. 8.6-9    Appearance of a Hanger 2)  Arrange the primary feeder cables before leading them into the equipment room. 3)  Fasten the primary feeder cables from top downward with hangers. Keep the cables straight all the way. Do not fasten the feeder cables at both ends simultaneously. 4)  If the antenna feeder system is installed on the top of a building, the network operator should install the cabling ladder on the wall. In this case, fasten the primary feeder cables with hangers along the ladder before leading them into the equipment room.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-208.6.6 Connecting Jumper Cable with Feeder Cable and Sealing Their Joint  Caution: Pay attention to the sealing of the joint between the feeder cable and the jumper cable, which is critical in the installation of the antenna feeder system. Use waterproof adhesive tape for the sealing. Generally, the 3m-long 1/2” jumper cable is used to connect the antenna and the primary feeder cable. Connect the 1/2” jumper cable with the primary feeder cable and then seal their joint as follows: 1.  Connect the antenna jumper cable with the connector of the primary feeder cable and then screw down the connector. 2.  Treat connectors with waterproof measures. The procedures are as follows:   1)  Wrap the waterproof adhesive tape around the joint from the sunk area upward (fill the area with the tape), as shown in Fig. 8.6-10.  Fig. 8.6-10    Schematic Diagram of Wrapping Waterproof Adhesive Tape (1) 2)  Stretch the tape with force and wrap it in the same direction as for fastening the cable connector. 3)  Wrap circularly in the reverse direction for the second layer, as shown in Fig. 8.6-11. Note that the next circle covers 1/3 of the previous circle for the purpose of preventing inleakage of rain. Wrap the joint for three layers totally. Do not cut the adhesive tape during the wrapping. The length of the cable wrapped with the tape should be 20mm longer than that of the connector.
 Chapter 8  Installation of Primary Antenna Feeder System  8-21   Fig. 8.6-11    Schematic Diagram of Wrapping Waterproof Adhesive Tape (2) 4)  After the wrapping, grip the joint with both hands to make the tape stuck tight with the joint, as shown in Fig. 8.6-12.  Fig. 8.6-12    Schematic Diagram of Wrapping Waterproof Adhesive Tape (3) 5)  Wrap two layers of PVC tape around the waterproof adhesive tape. Note that the next circle covers half of the previous circle. 6)  Grip the joint again. 7)  Use ties to fasten the wrapped part at both ends to prevent the tape from falling off due to aging. 8.6.7 Leading Primary Feeder Cable into Equipment Room 1. Precautions 1)  See Fig. 8.6-13 and Fig. 8.6-14 for the modes of leading the primary feeder cables into the equipment room. It must be ensured that no rainwater will be led in along the feeder cable. If necessary, the water-blocking curve can be made.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-22Feeder cable window One-time bending,with the min. radiusof more than 90mmCabling rack HangerOutdoorsIndoors Fig. 8.6-13    Leading the Feeder Cable into the Equipment Room - Mode 1 Feeder cablewindowOne-time bending,with the min. radiusof more than 90mmHangerCabling rackIndoorsOutdoors Fig. 8.6-14    Leading the Feeder Cable into the Equipment Room - Mode 2 2)  The feeder cables are led into the equipment room through the feeder cable window. The outdoor and indoor cabling racks are used for leading them. 2. Procedures 1)  Loosen the fasteners on the feeder cable window and remove the cover from the holes. 2)  Lead the feeder cables into the equipment room. Two people in and out of the room respectively should cooperate when leading the cables to prevent damaging both the equipment and the cable. Screw down the fastening hoop after the feeder cables are pulled in position. 3)  Cut the feeder cables. The following should be done before cutting them:
 Chapter 8  Installation of Primary Antenna Feeder System  8-23  Checking labels Check if the temporary labels are stuck on the cables. Without the labels, you might misconnect the cables.    Determining the cutting position Determine the cutting position based on the installation position of the shelf and the lightning arrester, length of jumper cable on top, and the bending radius of the feeder cables. 4)  Assemble the indoor connectors of the primary feeder cables. 8.6.8 Connecting Indoor Jumper Cable The indoor jumper cable on top is connected between the primary feeder cable and the antenna interface at the bottom of a micro-BTS. Customize a jumper cable on site based on the actual situation. One end of the jumper cable is a male N connector, which is directly connected to the bottom of the cabinet. The other end is a female DIN connector, which is connected to the 7/8” primary feeder cable. See Fig. 8.6-1. 8.7 Grounding System of Micro-BTS Grounding aims to protecting both the human being and the equipment against lightning shock and electromagnetic interference. The grounding system of a micro-BTS includes protection grounding on the chassis, lightning arrester for RF components in the cabinet, for GPS antenna, for T1 cables, for 120V AC power and for feeder cable grounding kit. 1.  Grounding principles of primary feeder cables 1)  Generally, each primary feeder cable should be grounded at least three times for lightning protection, that is, on the tower platform, between the tower and the outdoor cabling rack, and on the wall before the feeder cable is led into the equipment room. If the primary feeder cable is more than 60 meters long, a lightning grounding kit should be installed every 20 meters. If the primary feeder cable is shorter than 5m, one grounding point is enough. If the feeder cable is shorter than 20m but longer than 5m, it can be grounded at two points. 2)  The antenna feeder system, antenna mount and newly-installed cabling rack should all be welded to the lightning protection net of the building. The feeder
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-24cables should also be grounded at three points, that is, on the antenna pole, on the rooftop, and on the wall before the cables are led into the equipment room. 3)  Before leading the primary feeder cable along the outdoor cabling ladder from the top of the building to the equipment room, check whether the cabling ladder is grounded. If not, request the network operator to accomplish it as soon as possible. 2.  Procedures to install the grounding kit  Caution: It is prohibited to install the grounding kit in thunderstorm weather; otherwise, the installation personnel might be hurt. When installing the grounding kit, be sure to keep the feeder cable at the joint straight. 1)  Prepare such tools as paper knife, straight screwdriver, spanner and sharp nose pliers. 2)  Choose a suitable position for installing the grounding kit, and cut the sheath off the 7/8" feeder cable based on the size of the grounding kit. The structure of a grounding kit is shown in Fig. 8.7-1. Grounding terminal Grounding cableFeeder cableGrounding wire clipOut-layer coppercore of feeder cableSheet copper offeeder cable Fig. 8.7-1    Structure of a Grounding Kit 3)  Lead the grounding cable of the lightning grounding kit to the grounding net. Keep the angle between the grounding cable and the primary feeder cable no more than 15°.
 Chapter 8  Installation of Primary Antenna Feeder System  8-25If the antenna feeder system is installed on a tower, lead the grounding cable downward along the tower. If the antenna feeder system is installed on the top of a building, lead the grounding cable to the lightning protection net. 4)  Before installing the grounding kit, wrap the waterproof adhesive tape around the grounding cable near the grounding copper for sealing, as shown in Fig. 8.7-2.  Fig. 8.7-2  Schematic Diagram of Wrapping Waterproof Adhesive Tape Around the Grounding Cable 5)  Clamp the external conductor with the grounding copper and clip tightly. 6)  Seal the joint between the grounding kit and the feeder cable as follows:    First wrap the waterproof adhesive tape and then the PVC tap around the joint.    Wrap the waterproof adhesive tape circularly from bottom upward, and then from top downward, finally from bottom upward again. Note that the next circle covers half of the previous circle. 7)  Connect the grounding terminal of the grounding kit to the tower body or the cabling rack on the top of the building (the cabling rack is connected to the lightning protection net). Remove the paint and oxide at the junction within the radius of 13mm and then coat the clean area with antioxidant cream. After the connection, paint the area with antirust paint. 8)  Before the primary feeder cable is led into the equipment room, connect the grounding terminal of the grounding kit to the outdoor grounding busbar.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    8-268.8 Test of Antenna Feeder System 1.  After the antennae are installed and all feeder cables are connected, measure the standing wave ratio of them. 2.  Measure one end of the indoor 1/2” jumper cable, which is to be connected with the cabinet, with the tester. The standing wave ratio should be lower than 1.5. It is best to be lower than 1.3. 3.  Record the Voltage Standing Wave Ratio (VSWR) value and provide the VSWR testing diagram. 8.9 Waterproof Processing of Connectors Follow the steps below to seal the joints between two cables: 1.  Fasten the relative joints. 2.  Implement waterproof processing to the joints. 1)  Wrap the joints with the waterproof adhesive tape from the top of the connectors. The first layer should be wrapped in the same direction as for fastening the cable connectors. 2)  Stretch the tape with force and wrap it circularly for three layers totally. Note that the next circle covers half of the previous circle, and the wrap stops at the position about 10cm away from the joint. 3)  Grip the joint with force to make the tape stuck firmly with the joint. 4)  Wrap two layers of PVC tape around the waterproof adhesive tape in the same way as for wrapping the waterproof adhesive tape. 5)  Finally wrap a layer of anti-ultraviolet tape.
  9-19 Installation of GPS Antenna Feeder System  Summary      Describing the composition of the GPS antenna feeder system.    Describing the procedures to install the GPS antenna feeder system. 9.1 Preparations 9.1.1 Installation Personnel Before installing the GPS antenna feeder system, check the qualification of the installation personnel for working at heights, installation environment, security measures, installation tools and system components. The antenna feeder system is installed by the professional installation personnel under the monitoring of the installation supervisor. The installation supervisor should be familiar with the materials, tools and operations for the installation, who is responsible for assigning suitable work for the installation personnel and recording the actual engineering data. The installation personnel should be skillful and healthy. Those who work at heights should have obtained the corresponding qualification, have no acrophobia, observe the security regulations, and have purchased the personal accident insurance. In addition, they are prohibited from drinking alcohol when working. 9.1.2 Installation Environment Check if the outdoor lightning grounding cable is well grounded and if its cross-section area is more than 50mm2. Check if the distance between the antenna pole and the
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    9-2lightning rod/lightning grounding point/outdoor cabling rack, the firmness and wind-resistant ability of the pole meet the design requirements. In addition, check if the necessary tools and assisting materials are prepared, and if the route for laying the primary feeder cable are determined through negotiation. The equipment provider presents the requirements on the installation of the antenna mount based on the structure and size of the antenna, and the network operator should install the antenna mount as required. The network operator is also responsible for the installation of the outdoor cabling rack, lightning rod, lightning grounding point and outdoor lightning grounding cable. Moreover, the network operator needs to drill holes on wall or rooftop for installing the feeder cable window as one of the equipment room conditions. 9.1.3 Security Measures  Caution: The installation personnel working at heights must wear the safety belt, and those working on ground must wear the safety helmet. They must wear working clothes and shoes causing no slips when climbing up the tower. 1.  Safety precautions should be stressed to the installation personnel. 2.  The outdoor installation should be conducted in sunny days without strong wind. 3.  Obvious signs should be set in the installation site to notify irrelative people to keep away from the site. The installation personnel working on ground are obligate to keep irrelative people, esp. children away from the site. The tools used on the tower and some metal components might slip to cause casualties, so they must be put in a canvas tool bag when not used, and the bag must be sealed immediately after you open it for a tool or component. 9.1.4 Installation Tools 1.  Measurement tools: A compass, multimeter, inclinometer and tape measure; 2.  Communication tools: Two mobile phones; 3.  Raising tools: Pulley and rope; 4.  Special tools: Cutter for cutting primary feeder cables and tools for assembling connectors;
 Chapter 9  Installation of GPS Antenna Feeder System  9-35.  General tools: Adjustable wrench, sharp nose pliers, diagonal pliers, electrical knife, file and hacksaw; 6.  Protection tools: Safety belt, safety helmet, safety rope, thick working clothes, RF prevention clothes, canvas tool bag, gloves, and multi-purpose sockets; 7.  Other tools: Herringbone ladder and the wooden wheel axis for uplifting the primary feeder cable (which can be borrowed locally). 9.2 Composition of GPS Antenna Feeder System See Fig. 9.2-1 for the composition of the GPS antenna feeder system. SleeveFixing clipMicro-BTSGPS antennaCoaxial cable Fig. 9.2-1    Composition of the GPS Antenna Feeder System 9.3 Installation Procedures As the CDMA clock and frequency reference, GPS plays a very important role. The GPS antenna receives navigation and position signals of GPS satellites, demodulates frequency and clock signals through a GPS signal receiver and provides these signals to related elements of CDMA BTSs. 1.  Requirements on GPS antenna installation The GPS antenna should be installed in an open and high place, so that it can trace more satellites, for example, on the top of a building or on a tower. Make the GPS feeder cable as short as possible to minimize the attenuation. The GPS antenna should be installed in the lightning protection area of the tower; otherwise, a lightning rod should be customized and installed for the GPS antenna.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    9-42.  Assembly of a GPS coaxial cable connector 1)  Strip the a segment of sheath off the GPS coaxial cable as required in Fig. 9.3-1. 6.2 16.7  Fig. 9.3-1    Schematic Diagram of Length of Cable Sheath to be Stripped 2)  Assemble the components onto the cable as shown in Fig. 9.3-2. And then solder the core wire with the pin. Unfold the shielding layer and wrap it around the bushing. Pin Insulatingwasher Cable shieldingBushing Crimping tube Nut CableCable corewireSolderingtin  Fig. 9.3-2  Schematic Diagram of Soldering the Core Wire with the Pin 3)  Assemble the components into the shell, as shown in Fig. 9.3-3. Insulatingwasher Bushing CrimpingtubeShell NutPin  Fig. 9.3-3    Structure of N-J7A 3.  Procedures to install the GPS antenna feeder system 1) Assemble an outdoor coaxial cable connector following the same steps mentioned above.
 Chapter 9  Installation of GPS Antenna Feeder System  9-52) Insert the connector through the sleeve (a GPS accessory), and then lay the coaxial cable from the GPS antenna to the GPS lightning arrester. 3) Screw to connect the outdoor coaxial cable connector with the GPS antenna connector. 4)  Screw the sleeve onto the GPS antenna, keeping the GPS antenna unmoved. 5)  Secure the tube on the antenna pole with a fixing clip. 6) Cut the coaxial cable based on the installation position of the GPS lightning arrester. Assemble the indoor cable connector and then connect it with the lightning arrester. Do not wrongly connect the equipment terminal and antenna feeder terminal of the GPS lightning arrester. 7) Lay the coaxial cable from the GPS lightning arrester to the GPS port of a micro-BTS. 9.4 Test of Antenna Feeder System 1.  After the antennae are installed and all feeder cables are connected, measure the standing wave ratio of them. 2.  Measure one end of the indoor 1/2” jumper cable, which is to be connected with the cabinet, with the tester. The standing wave ratio should be lower than 1.5. It is best to be lower than 1.3. 3.  Record the VSWR value and provide the VSWR test diagram.
  10-110 Installation of Internal Modules  Summary      Describing the modules in a micro-BTS/remote station.    Describing the functions of the modules.    Describing the flow of installing the modules. 10.1 Overview 10.1.1 Logical Positions of Equipment Modules The modules and boards in M800T/M801T/M802T/M190T/M191T/M192T micro-BTS are positioned as shown in Fig. 10.1-1. BDMBRFSMPDMDIVMLNA1MLNA2MPAMDUPMGPSBGPSMLNAMPABRFSE1MTRXRFE-ANT0TXRX0RX110M/12M ANTRFE-ANT1Door Fig. 10.1-1    Modules and Boards in M800T/M801T/M802T/M190T/M191T/M192T Micro-BTS
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    10-2The modules and boards in R800T/R801T/R802T/R190T/R191T/R192T remote stations are positioned as shown in Fig. 10.1-2. RFMMPDMDIVMLNA1MLNA2MPAMDUPMLNAMPAMTRXRFE-ANT1TXRX0RX1RFE-ANT0DoorBRFSOptical fiber Fig. 10.1-2    Modules and Boards in R800T/R801T/R802T/R190T/R191T/R192T 10.1.2 Layout of Internal Modules A ZXCBTS micro-BTS is composed of Micro Transmitter & Receiver (MTRX) module, Micro Low Noise Amplifier (MLNA) module, Baseband Digital Module (BDM) module, Micro GPS (MGPS) module, Micro-BTS Power Distribution (MPD) 400W module, DIVersity (DIV) module, DUPlexer (DUP) module and Micro Power Amplifier (MPA) module, as shown in Fig. 10.1-3.
 Chapter 10  Installation of Internal Modules  10-3 1 MTRX  2 BDM  3 MPD400W  4 DIV 5 MLNA  6 MPA  7 Heater  8 DUP  9 MGPS Fig. 10.1-3    Layout of Modules in a ZXCBTS Micro-BTS A ZXCBTS remote station is composed of MTRX module, MLNA module, Remote Fiber Module (RFM), MPD 400W module, DIV module, DUP module and MPA module, as shown in Fig. 10.1-4.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    10-4 1 MTRX  2 RFM  3 MPD400W  4 DIV 5 MLNA  6 MPA  7 Heater  8 DUP Fig. 10.1-4    Layout of Modules in a ZXCBTS Remote Station 10.1.3 Functions of the Modules The following modules and accessories need be installed: 1. BDM BDM is the core module of a ZXCBTS micro-BTS, which completes the modulation & demodulation of baseband data, signaling processing, resources management and operation & maintenance functions. 2. MTRX MTRX provides interfaces to BDM and sends transmitted or received basedband data as well as the information on configuration, control, status and alarms. It achieves up conversion, intermediate frequency bandpass filter, transmit link gain control and signal amplification on forward links. Moreover, it
 Chapter 10  Installation of Internal Modules  10-5accomplishes down conversion, signal amplification and bandpass filter on reverse links. MTRX800 is used in M800T/M802T micro-BTS/remote stations, whereas M190T/M191T/M192T micro-BTS/remote stations adopt MTRX190. 3. MPA MPA receives CDMA signals transmitted by MTRX and then amplifies the power of the signals, which are finally emitted to a cell through the antenna after being processed by a duplexer filter. M800T micro-BTS/remote stations adopt MPA800; M802T micro-BTS/remote stations adopt MPA802; M190T/M191T micro-BTS/remote stations adopt MPA190T; M192T micro-BTS/remote stations adopt MPA192. 4. RFE Receive Front Element (RFE) consists of MDUP (Duplex), MDIV (Diversity) and MLNA. On reverse links, the signals received by the antenna are filtered by the duplexer filter and then amplified. On forward links, the signals outputted by MPA are filtered by the duplexer filter and then emitted to the cell through the antenna. 5. MPD MPD directly converts the 120V AC power into the power with suitable voltage and supply the power to all modules in a micro-BTS/remote station. Moreover, it controls the heater in a micro-BTS/remote station to maintain the internal environment stable. It also supports the monitoring of the power supply status. 6.  Optical interface module There are two kinds of optical interface modules used: OIM and RFM, which are respectively installed in a micro-BTS and a remote station. They accomplish the following functions: 1) Connecting BDS and RFS, providing channel for multiplexing and demultiplexing forward/reverse data and signaling, and carrying out optical-electrical conversion.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    10-62)  Multiplexing and demultiplexing LVDS signals. 3)  Providing 12MHz (800MHz) or 10MHz (1.9GHz) analog signals to the RF subsystem. 4)  Measuring the transmission delay of LFM (OIM) and RFM, and reporting the signal to RF Control Module (RFCM) through Integrated Circuit Interface Circuit (IIC) bus CM to compensate the transmission delay on Channel Processing Module (CHM). 5)  Reporting the alarm signals about temperature, humidity, and access control generated in a remote station to RFCM. 6)  Offering communication links between MPA and RFCM. 7)  Monitoring important signal, for example, 16chip. 7. GPSTM GPSTM functions in providing 16chip or pp2s clock signal, 10MHz reference signal and TOD messages.
 Chapter 10  Installation of Internal Modules  10-710.2 Module Installation Flow StartInstall MTRXIns tall RFMRemote s tatio nIns tall BDMInstall MGPSMicro-BTSInstall MPAInstall DUPInstall DIVInstall MPD400WIns tall MLANInstallation checkEndInstall the heaterBased on t heconfiguration Fig. 10.2-1  Module Installation Flow Diagram
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    10-810.3 Installation and Replacement of Modules  Note The modules and cables in Micro-BTS/remote stations have been installed, connected and tested before delivery. Before commissioning, you only need to check if they are loose due to conveyance. According to the configuration requirement, you might need to add optical fiber modules or CSM5000 expansion modules in the expansion slots of the corresponding BDM board. If any fault occurs, the maintenance personnel can refer to this manual for simple maintenance. 10.3.1 Installation Sequence  Note This section describes the sequence of module installation and cable connection in an M800 micro-BTS. Refer to this sequence for the installation in M801T/M802T/M190T/M191T/M192T/R800T/R190T/R191T/R192T micro-BTS. 1.  Install MTRX, BDM and BRFS. 2.  Install T1 lightning arrester and lay T1 cables. 3.  Connect Terminal B of DCDX02 and RSTDX to MPA and BRFS respectively, and bundle the cables with cable ties on the cable tie bases. 4.  Install MPD, BGPS, MGPS, MDIV, MLNA, MPA, RF and GPS lightning arrester. 5.  Lay interconnection cables between modules, access control cable and door grounding cable, and connect the antistatic wrist strap. 6.  Connect Terminal B of the RF cable RF27 to MDUP_ANT loosely. Next, install MDUP in the cabinet and then fasten it. Finally, connect the other two RF connectors on MDUP. 7.  Install the heater, power lightning arrester and connect the relative cables (including ACDX01).   10.3.2 Table of Cable Connections Refer to Appendix B.
 Chapter 10  Installation of Internal Modules  10-910.3.3 Fastening and Bundling of Internal Cables 1.  Fastening coaxial cables For semi-rigid coaxial cables, connect both ends to the corresponding terminals firmly. 2.  Bundling of GPS-BDM conductive wires and RF cables RF29/RF30 See Fig. 10.3-1. BDMBRFSBGPSMTRXMPDMDIVMLNA|1MLNA|2MPAMDUPAGPSTM307.5+0.1GPS-BDMRF30RF29To Terminal ABundle ofcablesT-shapeholeCable tie Fig. 10.3-1  Schematic Diagram of Bundling Internal Cables (1) Bundle the cables RF29 and RF30 on the door and the grounding cable of the antistatic wrist strap in the inner side of the bundling plank, while bundle the GPS-BDM cables in the outer side of it, as shown in Fig. 10.3-2.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    10-10GPS-BDM cable RF30 RF29Cable tie Bundling plank  Fig. 10.3-2  Schematic Diagram of Bundling Internal Cables (2) 3.  Bundling of DCDX01, DCDX02, RSTDX, MONDX01 and MONDX02 cables Bundle the cables DCDX01, DCDX02, RSTDX, MONDX01 and MONDX02 with cable ties on the cable tie bases, as shown in Fig. 10.3-3.   BDMMTRXMPDMDIVMLNA|1MLNA|2MPAMDUPCabletie baseMONDX02MONDX01DCDX01RSTDXDCDX02E1cableBRFSCabletie base Fig. 10.3-3  Schematic Diagram of Bundling Internal Cables (3)
 Chapter 10  Installation of Internal Modules  10-114.  Cabling of T1 cables in the cabinet The T1 lightning arrester is equipped with two T1 cables. Before connecting the T1 lightning arrester with the cabinet, label the T1 cables at the position near the connectors with “OUT#” or “IN#” (#=1, 2, 3 or 4”). “OUT#” and “IN#” should be the same as “OUT” or “IN” marked on the cable outlets at the back of the lightning arrester. When installing the T1 lightning arrester, ensure that the serial number “#” marked on the T1 cables is consistent with the silk-screen at the bottom of the BDM and the cabinet. To facilitate recabling the T1 cables connected with the lightning arrester, these T1 cables should be laid along the upper edge inside the cabinet, and the cable tie bases should be installed at the positions convenient for uninstallation. See Fig. 11-8. It is suggested to bundle the T1 cables with cable ties every 150mm. 10.3.4 Installation of OIM If a micro-BTS need be configured as a remote station, an OIM should be added on the BDM of the micro-BTS. See Fig. 10.3-4 for the corresponding relations between the OIM expansion slots in BDM and the sectors.   αsectorβγX26X15X16X27X17X18sectorsector Fig. 10.3-4    Corresponding Relations between OIM Expansion Slots in BDM and Sectors
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    10-12When inserting the OIM into the BDM, make the interface of the optical module on the OIM face outward to ensure that optical fibers can be inserted into the optical module of the OIM from the right side of the BDM, as shown in Fig. 10.3-5. BDMOIM slotOIM Optical interfacefacing outward Fig. 10.3-5  Schematic Diagram of Inserting the OIM into the BDM 10.3.5 Installation of LFM If a remote station need be configured for a macro-BTS, it is only necessary to replace TRX of a sector with LFM by just inserting LFM into the TRX slot in the TRX layer of the macro-BTS without changing any cable connections on the backplane. The RF modules such as TRX, HPA and RFE need not be installed in the macro-BTS. Refer to “7.2.1  Connecting Optical Fiber” for the connection with LFM and the cabling of optical fibers in a macro-BTS. 10.4 Points for Attention 1.  Main tool: Philips screwdriver. 2.  When installing MPA and MPD400W, cover the place between the MPA/MPD400W and the main radiator with silicon. 3.  The modules should be installed firmly and reliably.
  11-111 Hardware Installation Check  Summary      Describing the hardware installation check items 11.1 Checking Components in the Cabinet Check if: 1.  The RF cables between the modules are connected correctly and firmly. 2.  The bolts of all modules are screwed down to ensure reliable connections between the modules and the backplane. 3.  The unused connectors are screwed with matching terminals. 4.  The RF cables are not cross-connected or pulled too tight. Some margin is reserved at the turning corner and the connectors are connected firmly. 11.2 Checking the Cabinet Check if: 1.  The installation position of the cabinet complies with the design requirement. 2.  After the shelf is fixed, it is stable enough to resist earthquake of 7 in Richter scale. 3.  No part of the shelf is loose or damaged. The shelf is well painted and the indications on the shelf are complete, correct and clear. 4.  No metal scraps or useless wires are left in the cabinet. 5.  All bolts are screwed down, and flat washers and spring washers are installed without inversion.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    11-26.  The cable outlet at the bottom of the cabinet has been covered with the cover plate after the cables are connected. 7.  The combined cabinets are arranged in order and the connecting pieces on the top of the cabinets are fastened firmly. 8.  The surface of the cabinet is clean, the paint has no blemishes, and various indications on the surface are correct, clear and complete. 9.  The front door can be opened or closed flexibly. 11.3 Checking Cables Check if: 1.  All cables are laid straight and there are no cross-connections. Surplus cables are coiled, bundled and put in the cabling trough. 2.  The cables are turned smoothly. 3.  Power cables and signal cables are laid separately with a distance of more than 150mm. 4.  All cables are labeled clearly at both ends to avoid wrong or missed connections. 5.  The joints are reliable and well contacted without breaks or bends. 6.  The cables are tied with proper tightness, and the cable ties are distanced evenly. 7.  Surplus part of the cable ties for indoor cables has been cut. 8.  Some margin is reserved when the cable ties used on outdoor cables are cut. 9.  No cable tie has spininess part after being cut. 10.  All cables are stuck with labels indicating the usage, and the contents in the labels at both ends are the same. 11.  Stick the labels with transparent adhesive tape to prevent them from falling off. 11.4 Checking Power Cables and Grounding Cables Check if: 1.  The cabling of power cables and grounding cables conforms to the design requirements.
 Chapter 11  Hardware Installation Check  11-32.  The PGND cable of the micro-BTS adopts the olivine or yellow copper-core cable with the cross-section area of 35mm2, which is connected to the indoor PGND copper busbar reliably. The GND/BGND cable adopts the black copper-core cable with the cross-section area of 25mm2. The -48V power cable adopts the blue copper-core cable with the cross-section area of 25mm2. All these cables are laid straight and connected reliably. 3.  The grounding bus wire is directly connected to the indoor grounding busbar. The cross-section area of the grounding bus wire is more than 50mm2. 4.  Each terminal of the grounding copper busbar is connected with only one device. 5.  PGND cables and AC neutral cables are laid separately. 6.  AC neutral cables are grounded independently in the power room. 7.  The indoor grounding resistance is less than 5 ohm. 8.  Each cable is marked correctly and clearly. 9.  Power cables are not bundled with other cables but separately.   10.  The surplus part of the grounding and power cables are cut. 11.  The copper lugs at both ends of power cables and grounding cables are welded or crimped well. 12.  There is no joint (between two pieces of cables) for a piece of power cable or grounding cable. 13.  The grounding copper busbar is insulated from the wall, and the grounding path is as short as possible. 14.  The primary power supply is connected to the power terminal on the shelf correctly. 15.  The opening lug of power cables are welded or crimped firmly. 16.  Power cables are well contacted with the copper lugs and sealed with adhesive tape. The copper lugs are reliably connected with the power cabinet or BTS shelf. 17.  The power terminals on the top of the shelf are equipped with insulation tubes. 18.  No power cable, grounding cable, trunk cable or RF cable is broken.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    11-419.  The labels at both ends of the power cable and ground cable should be clear and correct.  20.  The naked wires at the wiring terminals and the handles of cable lugs are wrapped with insulation adhesive tape or heat-shrink tube. 21.  Each wiring terminal is installed with a flat washer and a spring washer. 11.5 Checking T1 Cables Check if: 1.  T1 cables are not short-circuited and the connectors are not damaged. 2.  T1 cables are connected correctly and stuck with clear labels. 3.  T1 cable connectors are firmly connected. Use the multimeter to test if the connectors are well connected with the grounding system. If the test result is negative, it might be caused by the poor contact between the flange of the connectors and the chassis. 4.  T1 cables are laid loosely to ensure firm connection with the connectors of the shelf when the cabling rack moves up and down. 5.  T1 cables are connected firmly and reliably. 11.6 Checking Indoor 1/2” Jumper Cables Check if: 1.  The primary feeder cable is connected with the 1/2” jumper cable, which is then connected to the wiring terminal on the top of the shelf. 2.  The indoor 1/2” jumper cables are stuck with labels indicating the corresponding sector and the length of the primary feeder cable. 3.  The indoor jumper cables are cabled and bundled neatly. 4.  The cabling is convenient for future maintenance and expansion. 5.  The jumper cables are laid in different layers and sectors. 6.  The jumper cable at the joint with the lightning arrester keeps straight for 30cm long.
 Chapter 11  Hardware Installation Check  11-511.7 Checking Primary Feeder Cables and GPS Feeder Cables Check if: 1.  The primary feeder cables are cut by a dedicated cutter. The cross-section is smooth and no copper scraps are left in the copper pipe of the primary feeder cable. The connectors of the primary feeder cables are installed firmly. 2.  The 7/8” feeder cable connectors are installed firmly to ensure normal standing wave ratio. 3.  The feeder cables are grounded at least three times as required (Refer to 6.2.3.1). The grounding points are connected firmly and sealed well. The end of the cable grounding kit for connecting the grounding cable is downward so that rainwater will not flow into the feeder cable along the grounding cable. 4.  One feeder cable grounding kit is installed in the middle of the tower if the tower is more than 60m high. 5.  One lightning grounding kit is installed on the top of a building or on the cabling rack if the length of the feeder cable after leaving the tower before entering the equipment room is more than 20m. 6.  The terminals of the feeder cable grounding kit are fixed separately onto the tower. 7.  The outdoor grounding copper busbar is connected with the underground grounding net by the dedicated cable whose cross-section area is more than 50mm2. 8.  The antenna feeder system on the top of a building is connected to the nearby lightning grounding net. 9.  The cabling ladder for leading the feeder cable from the building top along the wall to the equipment room is grounded. 10.  The inclination between the feeder cable and its grounding cable is less than 15°. 11.  The feeder cables are laid neatly, neither cross-connected nor broken or twisted. The connections with the sectors are correct. 12.  The minimum bending radius of feeder cables is 20 times of the semi-diameter of feeder cables or more. The bending radius of the primary feeder cables is larger than 0.3m.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    11-613.  The primary feeder cables of one sector are arranged in one row and they are queued the same in each row. 14.  No copper part of the feeder cable connectors is exposed. Same labels are stuck at both ends of a feeder cable with the cable length recorded. 15.  The GPS core wire is not falsely soldered. 16.  The GPS copper core is not short-circuited with the outer layer, and the core pins of the GPS feeder cable connectors are not exposed. 17.  The GPS feeder cable connectors are fastened tight. 11.8 Checking Water-blocking Curve for Feeder Cable Window and Primary Feeder Cables Check if: 1.  The feeder cable window is fixed on the wall in the equipment room, and the protruding holes of the feeder cable window are outward faced. 2.  The glue-injecting hole on sealing gasket of the feeder cable window is sealed upward. The window boards are installed in the indoor side of the window. 3.  The feeder cable window installed on the top of a building is well sealed. 4.  The lowest point of the water-blocking curve is at the place 10cm-20cm under the feeder cable window. 5.  The minimum bending radius of feeder cables is 20 times of the semi-diameter of feeder cables or more. The bending radius of the primary feeder cables is more than 0.3m. 6.  Keep a minimum length of 0.5m of straight feeder cable both in and out of the equipment room. There should be at least 0.3m of straight feeder cable in length through the lightning arrester. 11.9 Checking Hangers Check if: 1.  The hangers are fastened firmly on the outdoor cabling rack. 2.  The fixing clips installed are evenly distanced.
 Chapter 11  Hardware Installation Check  11-73.  The hangers are installed on the primary feeder cables every 1.5m.. 11.10 Checking Outdoor 1/2” Jumper Cables Check if:   1.  The connections between the antenna and the 1/2” jumper cable as well as the 1/2” jumper cable and the primary feeder cable are correct. Their joints are tightened. 2.  The jumper cable connected with the antenna is laid along the beam of the antenna mount and bound to the tower. 3.  The joints between the antenna and the 1/2” jumper cable as well as the 1/2” jumper cable and the primary feeder are sealed as required (Refer to 9.4.6 and 9.6.6). 4.  The jumper cable keeps straight with the antenna for 30cm long at their joint. 5.  All the connectors of outdoor jumper cables are sealed and water-blocking curve is made for jumper cables. 11.11 Checking Antenna Check if: 1.  The antenna mount is connected firmly with the tower. 2.  The type of the antenna installed meets the requirement of the networking plan. 3.  The height from the center of the antenna to the ground and the installation position of the antenna comply with the networking plan. 4.  The RF antenna and the GPS antenna are installed in the area protected by the lightning rod. 5.  The azimuth angle of each single-polarized directional antenna conforms to the networking plan. Two antennae of one sector are oriented to the same direction. The deviation of the azimuth angle of a directional antenna is within +/-5°. 6.  The pitch angle of each single-polarized antenna conforms to the networking plan. The deviation of the pitch angle of a directional antenna is within +/-0.5°. The pitch angle of two single-polarized antennae is the same.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    11-87.  There are two types of antenna: the pointer-modulated antenna and digital-modulated antenna. Adjust the former with a spanner and modulate the latter by setting the exact value in the equipment room. When the control line connecting the antenna is broken, you must adjust the antenna with a spanner. You must measure every single-polarized antenna. For digital-modulated antenna, keep the lower obliquity the same as planned, and keep consistency between the two single-polarized antennae. 8.  All antenna poles are installed stably and grounded well. They are vertical to the ground, with the deviation within 2°. 9.  The transceiving distance of omni antennae is no less than 3.5m. 10.  The distance between an omni antenna and the tower is more than 1.5m, and that between a directional antenna and the tower is more than 1m. 11.  The top of the jacket of an omni antennae is level with or higher than the antenna mount. 12.  The distance between an omni antenna and the antenna lightning rod is no less than 2.5m when the antenna situates on the rooftop. 13.  An omni antenna can cover all areas when it is installed on the rooftop. 14.  The diversity antenna of each sector corresponds with the jumper cables on top of the shelf. 15.  The diversity distance between two antennae of one sector refers to the vertical distance between two antennae. The diversity distance is more than 3.5m for a 800M micro-BTS/remote station; the diversity distance for a 1.9G micro-BTS/remote station is more than 1.5m; the diversity distance is more than 6.7m for a 450M micro-BTS/remote station. 16. The vertical distance between two directional antennae of different sectors installed on the same antenna mount is more than 0.6m. 17.  The antennae are separated from G-network antennae, distancing more than 1m vertically and more than 2m horizontally. 18.  The GPS antenna is installed in an open, low and safe place. It is vertical and its solid angle is bigger than 90°. 19.  A lightning rod is installed specially for the GPS antenna situated on rooftop.
 Chapter 11  Hardware Installation Check  11-911.12 Checking Standing Wave Ratio of Feeder Cables 1.  After the antennae are installed and all feeder cables are connected, measure the standing wave ratio of them. 2.  Measure one end of the indoor 1/2” jumper cable, which is connected with the cabinet, with the tester. The standing wave ratio should be lower than 1.5. It is best to be lower than 1.3. 3.  Record the VSWR value and provide the VSWR test diagram. 11.13 Checking Indoor and Outdoor Environment Check if: 1.  All waste materials are cleared, and the outdoor environment is clean. 2.  The equipment room is clean and neat, and all things needed are arranged in order. 3.  No waste materials such as cable ties, cables and desiccant bags are left around/under the shelf and under the raised floor. 4.  The front door, rear door and side panels are cleaned so that no touch prints can be seen. There is no dust or scrap in the cabinet.
  12-112 Power-on and Power-off  Summary      Describing the power-on check items     Describing the procedures to power on/off a micro-BTS/remote station 12.1 Checking Components in the Cabinet before Power-on Open the cabinet to check if the modules are installed firmly and the cables are connected reliably. Insert the OIM and the CSM5000 into the cabinet. Set the PATH ID by setting the DIP switch on the BDM based on the T1 cable connections with the CDSU of the BSC. See Fig. 12.1-1 for the setting of the DIP switch. PATH_ID12PATH_ID2PATH_ID3PATH_ID04ONOFFWhen PATH_ID=1, the DIP switch is set as:When PATH_ID=5, the DIP switch is set as:ONOFFONOFF31 Fig. 12.1-1    Setting of S1
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    12-212.2 Checking External Cables before Power-on 1.  Use the multimeter to measure if the 120V AC power meets the requirement. 2.  Check if the connector of the 120V AC power cable is connected firmly. 3.  Check if T1 cable connectors are connected tight. 4.  Check if the optical fibers are connected correctly. 5.  Use the tester to check if the standing wave ratio of the antenna feeder system is lower than 1.5. It should be lower than 1.3 generally. Check if feeder cable connectors are assembled correctly, and if the feeder cables and antennae are in good condition. 6.  Check if correct labels are stuck on the cables firmly. 12.3 Powering on/off the Cabinet No power switch is configured in micro-BTS or remote stations, so you need to power on/off them by plugging/unplugging the power connector or powering on/off the power supply equipment. After power-on, debug the BTS through the BSC.
  13-113 Installing the Integrated Micro-BTS  Summary   Describing the installation of the integrated built-in SDH of the micro-BTS   Describing the installation of the integrated UPS of the micro-BTS 13.1 Introduction to the Solution of Micro-BTS Integration 13.1.1 Implementation of the Micro-BTS Integration The micro-BTS integration solution integrates the transmission, power and micro-BTS technologies and devices to provide users with an integrated networking solution. The core of the CDMA micro-BTS integration of ZTE Corporation lies in the built-in SDH. Through improvement on the structure and cabling process of the micro-BTS and change of related boards, the SDH board is built into the micro-BTS. In addition, the integrated UPS is added to the micro-BTS to provide the micro-BTS with the interfacing and monitoring functions over the backup power supply (UPS power supply and combinational power supply) and other devices. Meanwhile, the functions of secondary power-off and dry contact monitoring are added to address new requirements. The built-in SDH and integrated UPS are optional for micro-BTS configuration. The following modifications to the micro-BTS are required if this function is to be added to the micro-BTS:   1.   BDM modification: Add the half-duplex RS485 monitoring interface and three dry contacts (input), no longer support the RS232 monitoring interface; 2. RFM modification: Add six dry contacts (input), not to support the RS485 and RS232 monitoring interface; 3. SDH selection: For the consistency of internal cabling, the CC4 connector is to be used for the T1 interface on the built-in SDH board, corresponding to the
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-2indoor T150 board for the transmission of this part. The indoor and outdoor T150 boards are the same except for the interface connector, that is to say, they are basically the same in terms of performance and reliability. Support of power supply: 24V and –48V input;   4. Improvement on cabling process: Consistent internal T1 cabling, that is, the same cabling can be inserted either to the BDM or the to built-in SDH to make upgrade and networking configuration more more convenient and flexible; internal cabling for the monitoring part;   5. Improvement on pinboard (bottom plate): Add a standalone built-in SDH power connector interface. The type of pinboard is settled on the 10W and 20W micro-BTS pinboard, 40W micro-BTS main cabient pinboard and 450M micro-BTS pinboard;   6. Add the lightning protection (class II) function for the monitoring part inside the cabinet with some lightning protection design on the board; furthermore, install an additional RS485/dry contact lightning protection board at the monitoring interface of the cabinet;   7. Modification of T1 lightning arrester: Because of the changed T1 cabling inside the cabinet, a longer coaxial cable may be needed for the T1 lightning arrester; in addition, codes of the T1 lightning arrester needs changing;   8. Improve the door panel structure of the micro-BTS, to build the SDH into the door panel of the micro-BTS.   13.1.2 Micro-BTS Integration Solution Thanks to above improvements on the micro-BTS, the integration solution now poses as an even simpler one with more flexible configuration available. With the solution of the micro-BTS integrated with the backup power supply and transmission, the user’s requirements are taken as the first priority. There comes two basic integration solutions for selection:   1.  AC micro-BTS+UPS+built-in SDH, as shown in Fig. 13.1-1.
Chapter  13  Installing the Integrated Micro-BTS  13-3AC micro-BTS UPS220V-48V485/dry contactFiber 1 (SDH)Fiber 2 (SDH)E1(1)E1(2)E1(3)E1(4)TransmissioninterfacePower supplyinterfaceBuilt-inSDH Fig. 13.1-1 Solution (I) of Micro-BTS Integration In this solution, a ZTE ZXSM T150 transmission system serves as the built-in SDH system, and a ZTE ZXUPS L010 UPS power system serves as the UPS power supply.On the power interface, the UPS provides 120V and -48V power outputs to supply power for the micro-BTS and built-in SDH. Furthermore, the UPS provides secondary power-off function to guarantee the power supply of the built-in SDH in precedence.485 or dry contact are supported for the monitoring. There is only one monitoring interface at the micro-BTS side and this interface is compatible with the 485 and dry contact input, that is, it supports either the 485 or dry contact for the monitoring part. On the transmission interface side, two STM-1 optical interfaces are supported and a maximum of four T1 interfaces can be provided. In addition, the built-in SDH or BDM board can be selected according to the actual requirements. 2.  DC micro-BTS+combinational power+built-in SDH, as shown in Fig. 13.1-2.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-4DC micro-BTSCombinationalpower supply-48V(1)-48V(2)485/dry contactFiber 1 (SDH)Fiber 2 (SDH)E1(1)E1(2)E1(3)E1(4)TransmissioninterfacePower supplyinterfaceBuilt-inSDH Fig. 13.1-2 Solution (II) of Micro-BTS Integration In this solution, a ZTE ZXSM T150 transmission system serves as the built-in SDH system, and a suitable ZTE power system model may serve as the outdoor combinational power supply. On the power interface side, the combinational power provides two -48V power outputs to supply power for the micro-BTS and the built-in SDH, Furthermore, the combinational power system provides the secondary power-off function to guarantee power supply for the built-in SDH in precedence. The monitor part and the transmission interface part are the same as those in Solution I. If the backup power is not available, the built-in SDH is also supported. However, the secondary power-off function cannot be implemented. To reduce power interfaces, the power of the built-in SDH can be supplied by the micro-BTS. In this case, a built-in 24V power and an SDH board are needed. Without the support of the backup power, if the electric power network is of poor quality, to reduce the influence of transmission interruption on the network due to power failure, it is recommended the configuration be used in a single station application only to avoid complicated SDH transmission networking. 13.1.3 Module Layout of the Integrated Micro-BTS and RF Remote Station Fig. 13.1-3 shows the module layout inside the ZXCBTS integrated micro-BTS:
Chapter  13  Installing the Integrated Micro-BTS  13-51413121110987654321 1 BDM module (top layer) 2 MTRX module (bottom layer) 3 power module 4 MDIV module 5 MLNA module 6. Heater 7 MPA module  8 T1 arrester  9 RF lightning arrester  10 MGPSTM lightning arrester  11 MTPB1 lightning-protection plate (the external 48VUPS should be built internally)     12 MDUP module    13 SDH board (if built-in SDH is necessary)  14  MGPSTM module    15 OIM board Fig. 13.1-3 Layout of Modules in the ZXCBTS micro-BTS
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-6Fig. 13.1-4 shows the module layout inside the ZXCBTS integrated RF remote station:   1098765321 1 RFM module (top layer) 2 MTRX module (bottom layer) 3 power module 4 MDIV module 5 MLNA module 6 Heater 7 MPA module 8 RF arrester 9 MTPB1 lightning protection plate (the external 48VUPS should be built internally) 10 MDUP module Fig. 13.1-4 Layout of Internal Modules of the ZXCBTS RF Remote Station
Chapter  13  Installing the Integrated Micro-BTS  13-713.1.4 Networking Modes of the Integrated SDH The built-in SDH technology is employed to make even more flexible networking of the micro-BTS and to address basically various networking requirements. The built-in SDH is a standard SDH STM-1 optical interface, which supports independent networking or networking with cooperation of an SDH device. The built-in SDH also supports directly fiber networking and has ring network protection capability. The built-in SDH cooperates with the SDH transmission equipment via standard T1 interfaces to flexibly support different networking modes such as point-to-point, chain, T-type, cross and ring modes and other hybrid networking modes. The built-in SDH micro-BTS supports independent networking or networking with cooperation of a standard SDH device. 13.2 Installing the Built-in SDH of Micro-BTS 13.2.1 Position and Internal Connection of the Built-in SDH in the Micro-BTS 13.2.1.1 Connections of the Built-in SDH Table 13.2-1 gives the cable connections of the built-in SDH in the CDMA micro-BTS.   Table 13.2-1 Cable Connection of the Built-in SDH inside the CDMA Micro-BTS No.  Cable Name  Length (mm)  To End A  To End B 1 Power cables  950  SDH-POWER (at the bottom of the cabinet)  SDH-X22 850 BDM_OUT1 SDH-R1 850 BDM_IN1 SDH-T1 850 BDM_OUT2 SDH-R2 2 RF cable 850 BDM_IN2 SDH-T2 3  F-DC PWR-002  5000  SDH-POWER (at the bottom of the cabinet) UPS power supply FIBER-3 (at the bottom of the cabinet)  SDH-D43 4  Fiber cable  As required on site FIBER-4 (at the bottom of the cabinet)  SDH-D44 13.2.1.2 Schematic Diagram of Internal Cable Connection Fig. 13.2-1 gives the cable layout of the built-in SDH in the CDMA micro-BTS.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-8 Door panelGPSBDMBottom SDH-POWERSDHMPDLNALNAMPADUPIN2 OUT2 IN1 OUT1ANT10MBRFSMTRX TXRX0RX1D43 D44T4R4T3R3T2R1T1R1X22OUT1IN1OUT2IN2OUT3IN3OUT4IN4 Fig. 13.2-1 Cable Layout of the Built-in SDH in the CDMA Micro-BTS 13.2.2 Connecting the External Optical Fibers and Cables During Installation 13.2.2.1 Description of the Cabinet-Bottom Interfaces Fig. 13.2-2 shows all the cabinet-bottom interfaces of the micro-BTS:   POWER FIBER-1 FIBER-2 FIBER-3 FIBER-4MONITOR FAN RFE-ANT0 RFE-ANT1 GPS-ANTEXTENDT1SDH-POWERIN4  OUT4  IN3  OUT3  IN2  OUT2  IN1  OUT1 Fig. 13.2-2 Cabinet-bottom Interfaces of the CDMA Micro-BTS
Chapter  13  Installing the Integrated Micro-BTS  13-9See below for the meaning of each connector:   POWER——Power input of the micro-BTS;   FIBER-1\-2——Extension fiber interface of the RF remote station;   FIBER-3\-4——Input/output of the built-in SDH fiber interface of the micro-BTS;  MONITOR——Communication interface of the external UPS of the micro-BTS; FAN——Fan interface for external heat dissipation of the high-power (over 20W) micro-BTS;   RFE-ANT0——Diversity reception antenna interface of the micro-BTS;   RFE-ANT1——Main reception / transmission antenna interface of the micro-BTS;   GPS-ANT——GPS antenna interface;   SDH-POWER——Built-in SDH power supply interface of the micro-BTS;   T1——Four 2M signal interfaces;   EXTEND——RF extension interface of the multi-carrier micro-BTS.   13.2.2.2 Description of the Fiber Installation Here the interfaces related with the built-in SDH are FIBER-3 and FIBER-4. FIBER-3 is the optical transmission input interface and FIBER-4 is the fiber transmission output interface used for networking with the adjacent BTS.   Fig. 13.2-3 shows the position for installing the water-proof fiber at the bottom of the micro-BTS cabinet and that for connecting and laying out the water-proof fiber inside the cabinet.   The water-proof connector of the fiber is connected with the cabinet body in the similar way to the fiber connection when the micro-BTS connects with the RF remote station. The fiber is laid out in a naturally way after it goes into the cabinet and is connected with the optical module on the SDH.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-10??????SDH?????Fiber water-proofconnectorSDH fiberconnector Fig. 13.2-3 Connection of the Optical Fiber 13.3 Installing the Integrated UPS of Micro-BTS/RF Remote Station 13.3.1 Introduction to ZXUPS L010 Currently, the integrated CDMA micro-BTS employs the ZXUPS L010 as its UPS. Fig. 13.3-1 shows the appearance of the ZXUPS L010 series products.
Chapter  13  Installing the Integrated Micro-BTS  13-11DANGER OF HIGH VOLTAGEShutter forair dischargeaCLOSEKeyOPENFront side ofenclosureRear side ofenclosureShutter for airadmittance Fig. 13.3-1 Appearance of the ZXUPS L010 Series Fig. 13.3-2 shows the inner structure of the ZXUPS L010 series.   外箱底部安装孔外箱底部出水孔外箱底部接地孔外箱底部出线孔外箱门外箱底部导槽外箱背部安装孔Door panelRear-sideinstallation holeWater outlet atthe bottomGrounding holeat the bottomLeading-out holeat the bottomInstallation holeat the bottomBottom slide Fig. 13.3-2 Inner Structure of the ZXUPS L010 Series 13.3.2 Precautions for UPS Installation The following rules should be followed if the micro-BTS (800M or 1.9G) is to be configured with an additional UPS:   1. The UPS must be kept within two meters away from the micro-BTS. Because current micro-BTS uses the BDM for monitoring the UPS and the RS-232 specification for communication, the communication distance is limited to 10 meters generally. To ensure correct communication, no more than two meters should better be kept between two cabinets. As the UPS is relatively close to the micro-BTS, lightning-protection may be ignored for between them.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-122. Improvement on the power connector of the micro-BTS. As the output of UPS is screwed with the bolt, the power supply of the current micro-BTS cannot be plugged. To improve this situation, a connector board may be used. Cut off the input 3-core connector on the connector board, divide by L-N-PE and connect respectively to the L-N-PE of the UPS’ output end. Be careful not to make any mistakes in this operation. In most cases, the brown line is for the live line (L), the blue line for neutral line (N) and the yellow-green line for protection grounding line (PE).   3. At present, the UPS employs the 232 communication mode and its RS232 interface differs from other standards. There are six pins in total — Pin 6: RXD (blue); Pin 7: GND (green); Pin 9: TXD (black), useful signal. The backup 232 interface of the BDM board is defined as: Pin 2: RXD; Pin 3: TXD; Pin 4: GND. Therefore, the 232 connector of UPS has to be changed, that is: Connect RXD (blue) to Pin 3 of DB9, TXD (black) to Pin 2 of DB9, and GND (green) to Pin 4 of DB9. Remember that the DB9 connector must be a “male” one.   4. Precautions for installation 1) Good ventilation for heat dissipation;   2) Keep from the place with corrosive gas;   3) The top of UPS must not be occupied by any objects, nor could it be taken by a sitting person, lest the air vent might be blocked;.   13.3.3 Structural Feature and Installation Mode of UPS The ZXUPS L010UPS features a compact structure and boasts functions of dust-proof, water-proof, thermal insulation, anti-burglary, damp-proof, mildew-proof and corrosion protection. It is suitable for the outdoor environment in a remote area with formidable natural conditions. With the modular design, the enclosure is not only neat-looking but also rust-proof with excellent performance. This device can be installed easily and if it is for outdoor use, it can be set up on the flat ground along with other delivery-attached fittings, that is, the floor-type installation.   Fig. 13.3-3 shows the floor-type installation of ZXUPS L010UPS.
Chapter  13  Installing the Integrated Micro-BTS  13-13M10×30内六角螺栓(4个)弹簧垫   (4个)平垫     (8个) M8膨胀螺丝(4个)M8螺母    (4个)地GroundSpring cushionPlain cushionM10x30 inner hexagon boltM8 nutM8 expansion screw(4pcs)(8pcs)(4pcs)(4pcs)(4pcs) Fig. 13.3-3 Frontal and Lateral Faces of the UPS’s Floor-type Installation 13.3.4 Installing the Engineering Cables of L010UPS 13.3.4.1 From-to-list Table 13.3-1 shows the connections of the CDMA micro-BTS 485 / dry contact supplementary cables.   Table 13.3-1 From-to-list of the CDMA Micro-BTS 485/dry contact supplementary cables No. Cable Name  Length (mm) To End A  To End B 1 Monitoring cable 800  BDM-RS485 MTPB1-X2 2 Monitoring cable 800  BDM-JOINT MTPB1-X1 3 Monitoring cable 470  MTPB1-X3  MONITOR at the cabinet bottom 4 Monitoring grounding cable 170  MTPB1  Grounding hole at the right side of the cabinet 5  Monitoring cable  3000  MONITOR at the cabinet bottom DB9 socket of UPS 13.3.4.2 Layout of Cabling Fig. 13.3-4 shows the layout of the monitoring cables of the CDMA micro-BTS 485/dry contact:
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-14Connected together with thefront-door grounding cableMTPB1 lightning-protection boardBottom MONOTOR  Fig. 13.3-4 Layout of the Monitoring Cables of the CDMA Micro-BTS 485/Dry Contact Here three interfaces, namely POWER, MONITOR and SDH-POWER are related to the external UPS.   Where, One cable end of POWER interface is connected with the POWER interface, and the other end is a standard 3-core power plug. To connect with the UPS, the 3-pin plug should be cut off first, then the three core wires (yellow-green, blue and brown, corresponding respectively to the ground line, neutral line and live line) should be connected with the output terminal of UPS properly;   For the cable connection of the MONITOR interface, refer to the above-mentioned from-to-list.   One end of the cable for the SDH-POWER interface is connected with this interface, and the other with the secondary power-off output connecting terminal of UPS, with the red and blue core wires connecting with the -48V, and the black and yellow-green ones with the ground.   13.3.5 Installing UPS As a product of ZTE, the ZXUPSL010 is delivered with the proper user’s manual
Chapter  13  Installing the Integrated Micro-BTS  13-15attached, and this manual gives detailed instructions on the installation of the product.   13.4 Installing the Ancillary Combinational Power Supply of Micro-BTS/RF Remote Station The following ancillary power supply is recommended for the devices of the CDMA cellular system: the ancillary combinational power supply consists of the outdoor power box and outdoor battery box (model: ZXDU28). The outdoor power box may be installed with a pole, on the wall or on the ground; while the outdoor battery box may only be installed on the ground.   Given below is the brief introduction of the installation method and connection of the outdoor power box and outdoor battery box.   13.4.1 Installing the Outdoor Power Box 13.4.1.1 Installing the Outdoor Power Box with a Pole Fig. 13.4-1 shows how the outdoor power box is installed on the pole.    1——Outdoor power box    2——Sunshade unit 1 (used for installation with a pole or on the wall)   3——Mechanical part of pole (used for installation with a pole)    4——Installation support (used for installation with a pole or on the wall) Fig. 13.4-1 Schematic Diagram of Installing the Outdoor Power Box with a Pole
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-1613.4.1.2 Installing the Outdoor Power Box on the Wall Fig. 13.4-2 shows how to install the outdoor power box on the wall.    1——Outdoor power box    2——Sunshade unit 1 (used for installation with a pole or on the wall)   3——Installation support (used for installation with a pole or on the wall)    4——Expansion bolt M10X50 Fig. 13.4-2 Schematic Diagram of Installing the Outdoor Power Box on the Wall 13.4.1.3 Installing the Outdoor Power Box on the Ground Fig. 13.4-3 shows how to install the outdoor power box on the ground.    1——Outdoor power box    2——Sunshade unit 2 (used for installation on the ground)
Chapter  13  Installing the Integrated Micro-BTS  13-173——Base (used for installation on the ground)    4——Expansion bolt M10X50 Fig. 13.4-3 Schematic Diagram of Installing the Outdoor Power Box on the Ground   13.4.2 Installing the Outdoor Battery Box The outdoor can only be installed on the ground, which is shown in Fig. 13.4-4.    1——Outdoor battery box    2——Sunshade unit 2 (used for the installation on the ground) 3——Base (used for installation on the ground)    4——Expansion bolt M10X50 Fig. 13.4-4 Schematic Diagram of Installing the Outdoor Battery Box on the Ground 13.4.3 Cable Connection for Outdoor Power Box The cable connection for the outdoor power box is presented in Fig. 13.4-5.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-18 1. Dry contact output connecting terminal    2. Load output working ground    3. Battery input working ground    4. –48V load output line 5. (-48V) battery input line    6. Cable holder    7. External AC input line    8. System’s cable access hole Fig. 13.4-5 Schematic Diagram of the Cable Connection for the Outdoor Power Box The function of dry contact monitoring is available with the combinational power supply of the micro-BTS. The actual definition of the dry contact’s output connecting terminal is (from top down): 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10, as shown in Fig. 13.4-6.
Chapter  13  Installing the Integrated Micro-BTS  13-1912345678910 Fig. 13.4-6 Output Connecting Terminal of the Dry Contact Precautions for the cable connection of the combinational power supply:  1. Description of dry contact pairs: As shown in the above figure, 1 and 2 are a pair of dry contacts (for the mains status alarm); 3 and 4 are a pair of dry contacts (for the battery under-voltage alarm); 5 and 6 are a pair of dry contacts (for the rectifier fault alarm); 7 and 8 are a pair of dry contacts (for the access control alarm). The micro-BTS monitors only the first three, that is, the access control monitoring is excluded. Between the dry contacts of the micro-BTS and the combinational power supply, a 7-core monitoring cable attached with delivery is used for the connection.   2. The cross-section area of the system’s AC input cable should be no smaller than 6mm2. 3. The cross-section area of the battery’s input cable should be no smaller than 16mm2. 4. The cross-section area of the DC load output cable should be no smaller than 10mm2. 5. There are clear silk-screen prints for the connecting terminals and the switch definitions under the corresponding devices. Please check them out before you go on with the connection or operation.   As the outdoor power box and outdoor battery box of the ancillary combinational
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    13-20power supply are products of ZTE, proper user’s manual will be attached with the product delivery. Detailed instructions are covered in these manuals for user’s reference during the installation.
  A-1Appendix A Packaging, Storage and Transportation  Summary      Describing how a micro-BTS/remote station is packed.    Describing how a micro-BTS/remote station should be stored.    Describing how a micro-BTS/remote station should be transported. A.1 Packaging The packaging of all components of micro-BTS, ultra-wide micro-BTS, and remote station are properly proofed against quakes during transportation. They are divided into two groups in packaging: 1. Cabinets 2.  Cables and delivery-attached document Each item has been identified with model, name, placement direction, number of layers, together with signs of “No damping”, and “Fragile” etc. A.2 Storage Keep all components in the original package. Keep the storeroom in order, and mark the number of equipment sets in stock. The range of temperature is -40°C ~+75°C, and the range of relative humidity is 5%~100%. Adopt measures of anti-moisture, anti-dust, quake-proof, and anti-erosion. It is recommended to equip air-conditioner and lighting equipment. The stock duration should be less than six months.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    A-2A.3 Transportation Use designated containers. All items should be placed closely, neatly, orderly and safely in the container to avoid any possible damage during transportation. There should be three layers of wooden box or four layers of cartons at maximum. Cables and delivery-attached document should be placed in the lower half and the cabinet should be placed in the upper half. Never put the equipment in open freight cars or ships. Never leave the equipment in open warehouses. Never transport the equipment with flammable, explosive or erosive chemicals. Keep the equipment away from being washed by rains and snow, or any physical damage. Keep the equipment away from electromagnetic or radiant substance during transportation. Ensure that all items are in the correct placement direction before being lifted during transportation.
  B-1Appendix B Table of Cable Connections  Summary     Refer to the following tables for the cable connections in micro-BTS and remote stations. B.1 Cable Connections in M800T Single-carrier Micro-BTS Table B.1-1    Cable Connections in M800T Single-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA800   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01 MPA800  MONDX02_B   6 MONDX02 MLNA800-1,-2  MONDX01_B   7 MPA CONTL MPA800  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX04  BDM800_X39  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet) Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester  The configuration in case that DC power
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-2Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester is supplied 20 RF21  MDIV800_RX  MLNA800-1_IN   21 RF22  MLNA800-2_IN  MDUP800_RX   22 RF23  MTRX800_RX0  MLNA800-1_RFOUT1   23 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   24 RF25  MTRX800_TX  MPA800_IN   25 RF26  MDIV800_ANT  RFE-ANT0 (at the bottom of the cabinet)   26 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  27 RF28  MPA800_OUT  MDUP800_TX   28 RF29  GPS-ANT at the bottom of the cabinet  MGPS_ANT  29 RF30  MGPS_10M  BDM800_X7   30  RF31  BDM800_X8  Middle hole of BRFS_X1   31 GPS-BDM  BDM800_X3  BGPS_X2    B.2 Cable Connections in M800T Double-carrier Micro-BTS Table B.2-1    Cable Connections in M800T Double-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA800   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01 MPA800  MONDX02_B   6 MONDX02 MLNA800-2  MONDX01_B   7 MPA CONTL MPA800  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX04  BDM800_X39  Door status switch
 Appendix B  Table of Cable Connections  B-3Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet) Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF22  (Black) MPD_V+  MDUP800_RX   21 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   22 RF25  MTRX800_TX  MPA800_IN   23 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  24 RF28  MPA800_OUT  MDUP800_TX   25 RF29  GPS-ANT (at the bottom of the cabinet)  MGPS_ANT  26 RF30  MGPS_10M  BDM800_X7   27  RF31  BDM800_X8  Middle hole of BRFS_X1   28 RF42  MLNA800-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   29 RF43  MTRX800_RX0  EXTEND (at the bottom of the cabinet)   30 GPS-BDM  BDM800_X3  BGPS_X2   Note: Please refer to precautions listed in Table B-1.  B.3 Cable Connections in R800T Single-carrier Remote Stations Table B.3-1    Cable Connections in R800T Single-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA800   3 DCDX03  MPD_X7  MLNA800
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-4Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA800  MONDX02_B   6 MONDX02  MLNA800-1, -2  MONDX01_B   7 MPA CONTL  MPA800  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet) Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001  POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003  (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF21  MDIV800_RX  MLNA800-1_IN   21 RF22  MLNA800-2_IN  MDUP800_RX   22 RF23  MTRX800_RX0  MLNA800-1_RFOUT1   23 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   24 RF25  MTRX800_TX  MPA800_IN   25 RF26  MDIV800_ANT  RFE-ANT0 (at the bottom of the cabinet)   26 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  27 RF28  MPA800_OUT  MDUP800_TX   28  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   29  RF41  RFM_X7  Middle hole of RFM_X3
 Appendix B  Table of Cable Connections  B-5B.4 Cable Connections in R800T Double-carrier Remote Stations Table B.4-1    Cable Connections in R800T Double-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA800   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA800  MONDX02_B   6 MONDX02  MLNA800-2  MONDX01_B   7 MPA CONTL  MPA800  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet) Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001  POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003  (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF22  MLNA800-2_IN  MDUP800_RX   21 RF24  MTRX800_RX1 MLNA800-2_RFOUT1  22 RF25  MTRX800_TX  MPA800_IN   23 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  24 RF28  MPA800_OUT  MDUP800_TX   25  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   26  RF41  RFM_X7  Middle hole of RFM_X3   27 RF42  MLNA800-2_RFOUT2 RFE-ANT0 (at the bottom of the cabinet)
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-6Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 28 RF43  MTRX800_RX0  EXTEND (at the bottom of the cabinet)    B.5 Cable Connections in M190T Single-carrier Micro-BTS Table B.5-1    Cable Connections in M190T Single-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA800   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA800  MONDX02_B   6 MONDX02  MLNA800-1, -2  MONDX01_B   7 MPA CONTL MPA800  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02  Cabinet BDM   10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF21  MDIV800_RX  MLNA800-1_IN   21 RF22  MLNA800-2_IN  MDUP800_RX   22 RF23  MTRX800_RX0  MLNA800-1_RFOUT1   23 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   24 RF25  MTRX800_TX  MPA800_IN
 Appendix B  Table of Cable Connections  B-7Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 25 RF26  MDIV800_ANT  RFE-ANT0 (at the bottom of the cabinet)   26 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  27 RF28  MPA800_OUT  MDUP800_TX   28  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   29  R41  RFM_X7  Middle hole of RFM_X3    B.6 Cable Connections in M190T Double-carrier Micro-BTS Table B.6-1    Cable Connections in M190T Double-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA800   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA800  MONDX02_B   6 MONDX02  MLNA800-2  MONDX01_B   7 MPA CONTL  MPA800  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001  POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003  (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-8Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 20 RF22  MLNA800-2_IN  MDUP800_RX   21 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   22 RF25  MTRX800_TX  MPA800_IN   23 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  24 RF28  MPA800_OUT  MDUP800_TX   25  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   26  RF41  RFM_X7  Middle hole of RFM_X3   27 RF42  MLNA800-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   28  RF43  MTRX800_RX0  EXTEND (at the bottom of the cabinet)    B.7 Cable Connections in R190T Single-carrier Remote Stations Table B.7-1    Cable Connections in R190T Single-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA800   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA800  MONDX02_B   6 MONDX02  MLNA800-2  MONDX01_B   7 MPA CONTL  MPA800  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied
 Appendix B  Table of Cable Connections  B-9Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 17 F-DC PWR-001  POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003  (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF22  MLNA800-2_IN  MDUP800_RX   21 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   22 RF25  MTRX800_TX  MPA800_IN   23 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  24 RF28  MPA800_OUT  MDUP800_TX   25  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   26  RF41  RFM_X7  Middle hole of RFM_X3   27 RF42  MLNA800-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   28  RF43  MTRX800_RX0  EXTEND (at the bottom of the cabinet)    B.8 Cable Connections in R190T Double-carrier Remote Stations Table B.8-1    Cable Connections in R190T Double-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA1900   3 DCDX03  MPD_X7  MLNA1900   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA1900  MONDX02_B   6 MONDX02  MLNA1900-2  MONDX01_B   7 MPA CONTL  MPA1900  MTRX1900   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-10Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF25  MTRX1900_TX  MPA1900_IN   21 RF33  MLNA1900-2_IN  MDUP1900_RX   22 RF34  MPA1900_OUT  MDUP1900_TX   23 RF36  MTRX1900_RX1  MLNA1900-2_RFOUT1   24 RF38  RFE-ANT1 (at the bottom of the cabinet)  MDUP1900_ANT  25  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   26  RF41  RFM_X7  Middle hole of RFM_X3   27 RF42  MLNA1900-2_RFOUT2 RFE-ANT0 (at the bottom of the cabinet)   28  RF43  MTRX1900_RX0  EXTEND (at the bottom of the cabinet)    B.9 Cable Connections in M802T Single-carrier Micro-BTS Table B.9-1    Cable Connections in M802T Single-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  MLNA800-1, -2  MONDX01_B   7 MPA CONTL  MPA  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM
 Appendix B  Table of Cable Connections  B-11Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 10 DX03  Cabinet  Door   11  DX04  BDM802_X39  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20  F-FAN-004  MPD  Internal fan rack   21 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  22 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan rack   23 RF21  MDIV800_RX  MLNA800-1_IN   24 RF22  MLNA800-2_IN  MDUP800_RX   25 RF23  MTRX800_RX0  MLNA800-1_RFOUT1   26 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   27 R25  MTRX800_TX  MPA_IN   28 RF26  MDIV800_ANT  RFE-ANT0 (at the bottom of the cabinet)   29 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  30 RF28  MPA_OUT  MDUP800_TX   31 RF29  GPS-ANT at the bottom of the cabinet  MGPS_ANT  32 RF30  MGPS_10M  BDM802_X7   33  RF31  BDM802_X8  Middle hole of BRFS_X1   34 GPS-BDM  BDM802_X3  BGPS_X2
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-12B.10 Cable Connections in M802T Double-carrier Micro-BTS Table B.10-1    Cable Connections in M802T Double-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  MLNA800-2  MONDX01_B   7 MPA CONTL MPA  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX04  BDM802_X39  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20  F-FAN-004  MPD  Internal fan rack   21 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  22 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan   23 RF22  (Black) MPD_V+  MDUP800_RX   24 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   25 RF25 MTRX800_TX MPA_IN   26 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  27 RF28  MPA_OUT  MDUP800_TX
 Appendix B  Table of Cable Connections  B-13Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 28 RF29  GPS-ANT at the bottom of the cabinet  MGPS_ANT  29 RF30  MGPS_10M  BDM802_X7   30  RF31  BDM802_X8  Middle hole of BRFS_X1   31 RF42  MLNA800-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   32  RF43  MTRX800_RX0  EXTEND (at the bottom of the cabinet)   33 GPS-BDM  BDM802_X3  BGPS_X2    B.11 Cable Connections in R802 Single-carrier RF Remote Stations Table B.11-1    Cable Connections in R802T Single-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  MLNA800-1, -2  MONDX01_B   7 MPA CONTL MPA  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   9 DX02  Cabinet  Lightning arrester    10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-14Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 20 RF21  MDIV800_RX  MLNA800-1_IN   21 RF22  MLNA800-2_IN  MDUP800_RX   22 RF23  MTRX800_RX0  MLNA800-1_RFOUT1   23 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   24 RF25  MTRX800_TX  MPA_IN   25  RF26  MDIV800_ANT  RFE-ANT0 (at the bottom of the cabinet)   26 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  27 RF28  MPA_OUT  MDUP800_TX   28  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   29  RF41  RFM_X7  Middle hole of RFM_X3   30 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  31 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan    B.12 Cable Connections in R802T Double-carrier Remote Stations Table B.12-1    Cable Connections in R802T Double-carrier RF Remote Stations Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  MLNA800   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  MLNA800-2  MONDX01_B   7 MPA CONTL MPA  MTRX800   8  DX01  Door grounding point  Cabinet grounding point   9 DX02  Cabinet  Lightning arrester    10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) The configuration in case that AC power
 Appendix B  Table of Cable Connections  B-15Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF22  MLNA800-2_IN  MDUP800_RX   21 RF24  MTRX800_RX1  MLNA800-2_RFOUT1   22 RF25  MTRX800_TX  MPA_IN   23 RF27  RFE-ANT1 (at the bottom of the cabinet)  MDUP800_ANT  24 RF28  MPA_OUT  MDUP800_TX   25  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   26  RF41  RFM_X7  Middle hole of RFM_X3   27 RF42  MLNA800-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   28  RF43  MTRX800_RX0  EXTEND (at the bottom of the cabinet)   29 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  30 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan    B.13 Cable Connections in M191T Single-carrier Micro-BTS Table B.13-1    Cable Connections in M191T Single-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  LNA   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  LNA-1, -2  MONDX01_B   7 MPA CONTL  MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-16Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX04  BDM_X39  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF25  TRX_TX  MPA_IN   21 RF29  GPS-ANT at the bottom of the cabinet  MGPS_ANT  22 RF32  DIV_RX  LNA-1_IN   23 RF33  LNA-2_IN  DUP_RX   24 RF34  MPA_OUT  DUP_TX   25 RF35  TRX_RX0  LNA-1_RFOUT1   26 RF36  TRX_RX1  LNA-2_RFOUT1   27 RF37  DIV_ANT  RFE-ANT0 (at the bottom of the cabinet)   28 RF38  RFE-ANT1 (at the bottom of the cabinet)  DUP_ANT  29  RF39  MGPS_10M  Middle hole of BRFS_X1   30 GPS-BDM  BDM_X3  BGPS_X2    B.14 Cable Connections in M191T Double-carrier Micro-BTS Table B.14-1    Cable Connections in M191T Double-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11
 Appendix B  Table of Cable Connections  B-17Serial No.  Cable Name  Connection of Terminal A  Connection of Terminal B  Remarks 2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  LNA   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  LNA-2  MONDX01_B   7 MPA CONTL  MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX04  BDM_X39  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF25  TRX_TX  MPA_IN   21 RF29  GPS-ANT at the bottom of the cabinet  MGPS_ANT  22 RF33  LNA-2_IN  DUP_RX   23 RF34  MPA_OUT  DUP_TX   24 RF36  TRX_RX1  LNA-2_RFOUT1   25 RF38  RFE-ANT1 (at the bottom of the cabinet)  DUP_ANT  26  RF39  MGPS_10M  Middle hole of BRFS_X1   27 RF42  LNA-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   28  RF43  TRX_RX0  EXTEND (at the bottom of the cabinet)   29 GPS-BDM  BDM_X3  BGPS_X2
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-18B.15 Cable Connections in R191T Single-carrier Remote Stations Table B.15-1    Cable Connections in R191T Single-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  LNA   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  LNA-1, -2  MONDX01_B   7 MPA CONTL  MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF25  TRX_TX  MPA_IN   21 RF32  DIV_RX  LNA-1_IN   22 RF33  LNA-2_IN  MDUP1900_RX   23 RF34  MPA_OUT  MDUP1900_TX   24 RF35  TRX_RX0  LNA-1_RFOUT1   25 RF36  TRX_RX1  LNA-2_RFOUT1   26 RF37  DIV_ANT  RFE-ANT0 (at the bottom of the cabinet)   27 RF38  RFE-ANT1 (at the bottom of the cabinet)  MDUP1900_ANT  28  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   29  RF41  RFM_X7  Middle hole of RFM_X3
 Appendix B  Table of Cable Connections  B-19B.16 Cable Connections in R191T Double-carrier Remote Stations Table B.16-1    Cable Connections in R191T Double-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  LNA   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  LNA-2  MONDX01_B   7 MPA CONTL  MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF25  TRX_TX  MPA_IN   21 RF33  LNA-2_IN  MDUP1900_RX   22 RF34  MPA_OUT  MDUP1900_TX   23 RF36  TRX_RX1  LNA-2_RFOUT1   24 RF38  RFE-ANT1 (at the bottom of the cabinet)  MDUP1900_ANT  25  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   26  RF41  RFM_X7  Middle hole of RFM_X3   27 RF42  LNA-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   28  RF43  TRX_RX0  EXTEND (at the bottom of the cabinet)
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-20B.17 Cable Connections in M192T Single-carrier Micro-BTS Table B.17-1    Cable Connections in M192T Single-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  MLNA   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  MLNA-1, -2  MONDX01_B   7 MPA CONTL  MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02 Cabinet BDM  10 DX03  Cabinet  Door   11  DX04  BDM_X39  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20  F-FAN-004  MPD  Internal fan rack   21 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  22 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan rack   23 RF25  TRX_TX  MPA_IN   24 RF29  GPS-ANT at the bottom of the cabinet  MGPS_ANT  25 RF32  DIV_RX  LNA-1_IN   26 RF33  LNA-2_IN  DUP_RX   27 RF34  MPA_OUT  DUP_TX   28 RF35  TRX_RX0  LNA-1_RFOUT1
 Appendix B  Table of Cable Connections  B-21Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 29 RF36  TRX_RX1  LNA-2_RFOUT1   30 RF37  DIV_ANT  RFE-ANT0 (at the bottom of the cabinet)   31 RF38  RFE-ANT1 (at the bottom of the cabinet)  DUP_ANT  32  RF39  MGPS_10M  Middle hole of BRFS_X1   33 GPS-BDM  BDM_X3  BGPS_X2    B.18 Cable Connections in M192T Double-carrier Micro-BTS Table B.18-1    Cable Connections in M192T Double-carrier Micro-BTS Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  MLNA   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  MLNA-2  MONDX01_B   7 MPA CONTL  MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point   Cabinet Lightning arrester  9 DX02  Cabinet BDM   10 DX03  Cabinet  Door   11  DX04  BDM_X39  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-22Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 20  F-FAN-004  MPD  Internal fan rack   21 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  22 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan   23 RF25  TRX_TX  MPA_IN   24 RF29  GPS-ANT at the bottom of the cabinet  MGPS_ANT  25 RF33  LNA-2_IN  DUP_RX   26 RF34  MPA_OUT  DUP_TX   27 RF36  TRX_RX1  LNA-2_RFOUT1   28 RF38  RFE-ANT1 (at the bottom of the cabinet)  DUP_ANT  29  RF39  MGPS_10M  Middle hole of BRFS_X1   30 RF42  LNA-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   31  RF43  TRX_RX0  EXTEND (at the bottom of the cabinet)   32 GPS-BDM  BDM_X3  BGPS_X2    B.19 Cable Connections in R192T Single-carrier Remote Stations Table B.19-1    Cable Connections in R192T Single-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  LNA   4 RSTDX  MPD_X5  BRFS_X6   5 MONDX01  MPA  MONDX02_B   6 MONDX02  LNA-1, -2  MONDX01_B   7 MPA CONTL  MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point   9 DX02  Cabinet  Lightning arrester    10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester
 Appendix B  Table of Cable Connections  B-23Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown) 14 ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF25  TRX_TX  MPA_IN   21 RF32  DIV_RX  LNA-1_IN   22 RF33  LNA-2_IN  MDUP1900_RX   23 RF34  MPA_OUT  MDUP1900_TX   24 RF35  TRX_RX0  LNA-1_RFOUT1   25 RF36  TRX_RX1  LNA-2_RFOUT1   26 RF37  DIV_ANT  RFE-ANT0 (at the bottom of the cabinet)   27 RF38  RFE-ANT1 (at the bottom of the cabinet)  MDUP1900_ANT  28  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   29  RF41  RFM_X7  Middle hole of RFM_X3   30 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  31 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan    B.20 Cable Connections in R192T Double-carrier Remote Stations Table B.20-1    Cable Connections in R192T Double-carrier Remote Stations Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 1 DCDX01  BRFS_X5  MPD_X11   2 DCDX02  MPD_X6  MPA   3 DCDX03  MPD_X7  LNA   4 RSTDX  MPD_X5  BRFS_X6
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    B-24Serial No.  Cable Name  Connection of Terminal A Connection of Terminal B  Remarks 5 MONDX01  MPA  MONDX02_B   6 MONDX02  LNA-2  MONDX01_B   7 MPA CONTL MPA  TRX   8  DX01  Door grounding point  Cabinet grounding point   9 DX02  Cabinet  Lightning arrester    10 DX03  Cabinet  Door   11  DX05  RFM_X24  Door status switch   12  DX06  MPD_X4  Power lightning arrester   13 ACDX03  MPD_HP  Heater   Power lightning arrester (blue, brown)  14  ACDX01  POWER (at the bottom of the cabinet)  Grounding point (black) 15  ACDX02  MPD_X1  Power lightning arrester 16 ACDX04  ACDX01_A  External AC power The configuration in case that AC power is supplied 17 F-DC PWR-001 POWER (at the bottom of the cabinet)  Power lightning arrester 18  F-DC PWR-002  F-DC PWR-001_A  External -48V power 19 F-DC PWR-003 (Blue) MPD_V- (Black) MPD_V+  Power lightning arrester The configuration in case that DC power is supplied 20 RF25  TRX_TX  MPA_IN   21 RF33  LNA-2_IN  MDUP1900_RX   22 RF34  MPA_OUT  MDUP1900_TX   23 RF36  TRX_RX1  LNA-2_RFOUT1   24 RF38  RFE-ANT1 (at the bottom of the cabinet)  MDUP1900_ANT  25  RF40  Middle hole of BRFS_X1  Middle hole of BRFS_X3   26  RF41  RFM_X7  Middle hole of RFM_X3   27 RF42  LNA-2_RFOUT2  RFE-ANT0 (at the bottom of the cabinet)   28  RF43  TRX_RX0  EXTEND (at the bottom of the cabinet)   29 F-FAN-005  COMMAN (at the bottom of the cabinet)  MPD  30 F-FAN-006  COMMAN (at the bottom of the cabinet)  External fan
  C-1Appendix C Equipment Parameters C.1 Dimension See Fig. C.1-1 for the appearance of a micro-BTS/remote station cabinet.  Fig. C.1-1    Appearance of a ZXCBTS Cabinet The dimension of the cabinet is 630mm (height)×400mm (width)×285mm (depth). The weight of one cabinet is 45kg.   C.2 Power Consumption Refer to the following table for the power consumption of several types of micro-BTS and remote stations supplied with the 120V AC power in case of full load.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    C-2Table C.2-1    Power Consumption of Several Types of Micro-BTS and Remote Stations Model Power Consumption M190T 180W M191T 195W M192T 290W M800T 195W M802T 290W R190T 180W R191T 195W R192T 290W R800T 195W R802T 290W Power factor: 0.5 Refer to the following table for the power consumption of several types of micro-BTS and remote stations supplied with the 120V AC power in case of full load when they are configured with heaters. Table C.2-2    Power Consumption of Several Types of Micro-BTS and Remote Stations Model  Power Consumption (Watt) M190T 280W M191T 295W M192T 390W M800T 295W M802T 390W R190T 280W R191T 295W R192T 390W R800T 295W R802T 390W Power factor: 0.5 Note: When the temperature is lower than -10°C, a heater can be added. Currently, only the equipment supplied with 120V AC power support this function. DC equipment does not support this function.
 Appendix C  Equipment Parameters  C-3Refer to the following table for the power consumption of several types of micro-BTS and remote stations supplied with the -48V DC power in case of full load. Table C.2-3    Power Consumption of Several Types of Micro-BTS and Remote Stations Model  Power Consumption (Watt) M190T 180W M191T 195W M192T 290W M800T 195W M802T 290W R190T 180W R191T 195W R192T 290W R800T 195W R802T 290W
  D-1Appendix D Indicators D.1 BDM Indicators See Fig. D.1-1 for the BDM indicators and their meanings. HL4HL7HL8HL5HL6HL16HL11HL10HL3HL9HL17HL18HL12HL13HL14HL15HL2HL1HL4: 3.3V power indicatorHL7: 5V power indicatorHL8: 12V power indicatorHL3: Synchronization indicator for the first channel of E1.On: asynchronized; Off: synchronized.HL9: Synchronization indicator for the second channel ofE1. On: asynchronized; Off: synchronized.HL17: Synchronization indicator for the third channel of E1.On: asynchronized; Off: synchronized.HL18: Synchronization indicator for the fourth channel ofE1. On: asynchronized; Off: synchronized.HL2: EPLD running indicator. On: Normal; Off: Not writtenHL1: FPGA running indicator. On: Not downloaded; Off:Downloaded.HL5: System running indicator. On: Not started; Flashslowly: Loading data; Flash fast: Running normally.HL10: Alarm indicator. Off: No alarm is generated; Flashquickly: An alarm is generated.HL6, HL16 and HL11: Reserved.HL12 ~ HL15: 10M Ethernet network running indicator.Used for debugging.  Fig. D.1-1    Indicators of the BDM D.2 Indicators on Front Panel of MGPS Refer to Table D.2-1 for the indicators on the front panel of MGPS and their meanings. Table D.2-1    Indicators on the Front Panel of MGPS Meaning Indicator On Off RUN (Green)  Indicates that the equipment is working normally. Indicates that the equipment is abnormal.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    D-2Meaning Indicator On Off WARM UP (Green)  Indicates that the equipment is warming up. Indicates that the equipment is working normally. GPS ALM (Green) Indicates that the equipment is in initialization status, unlocked status or in status in which satellite signals cannot be received. If it flashes, it indicates that the GPS antenna is disconnected. Other causes 1PPS ALM (Green)  Indicates that the 1PPS detection accuracy exceeds the required range (800ns). Indicates that the 1PPS detection accuracy meets the requirement (800ns). FAULT (Red)  Indicates that the equipment is faulty. Check TOD messages for the cause. Indicates that the equipment is working normally. 10MHz (Red)  No output  Output of 10MHz   19.6608MHz (Red)  No output  Output of 19.6608MHz   PP2S (Red)  No output  Output of PP2S D.3 Indicators of LFM, RFM and OIM 1.  Refer to the following table for the LFM indicators and their meanings. Table D.3-1    Indicators of the LFM Indicator Meaning POWER (Red)  Power indicator. When it is on, it indicates that power is being supplied. CLKER (Red)  Clock alarm indicator. When it is on, it indicates that no clock signal is recovered in the LFM. TXCLK (Green)  Tx clock indicator. When it is on, it indicates that the multiplexing chip in the LFM locks the Tx clock. FIBIN (Green)  Optical signal indicator. When it is on, it indicates that optical signal is entering the optical interface. RXREADY (Green)  Data receiving indicator. When it is on, it indicates that the LFM is recovering the data from the optical links correctly.
 Appendix D  Indicators  D-32.  Refer to the following table for the RFM indicators and their meanings. Table D.3-2    Indicators of the RFM Indicator Meaning HL7  ALARMCLK (Red) Clock alarm indicator. When it is on, it indicates that the RFM cannot recover the 16chip clock signal from the optical links correctly. HL2  PLLLOST (Red)  Phase-locked loop indicator. When it is on, it indicates that the phase-locked loop of the RFM is unlocked. HL12  TEMP_INT (Red)  Temperature alarm indicator. When it is on, it indicates that the temperature is too high. HL11  OPT_DETECT (Green) PP2S indicator. When it flashes every 2 seconds, it indicates that the links are normal. HL10  DOOR (Green)  Door control indicator. When it is on, it indicates that the door is opened. HL9  SD_ALARM (Green)  Optical signal alarm indicator. When it is on, it indicates that nooptical signal enters the optical interface. HL3  3.3V (Green)  3.3V power indicator. When it is on, it indicates that the 3.3V power is supplied normally. HL1  5V (Green)  5V power indicator. When it is on, it indicates that the 5V power is supplied normally. HL4  12V (Green)  12V power indicator. When it is on, it indicates that the 12V power is supplied normally. HL6  1032LOCK (Green)  Tx clock indicator. When it is on, it indicates that the multiplexing chip in the RFM locks the Tx clock. HL17  1034RDY (Green)  Data receiving indicator. When it is on, it indicates that the RFM is recovering the data from the optical links correctly. HL8    LVDS_TEST  Test indicator. It is always off.
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    D-43.  See Fig. D.3-1 for the location of the indicators on the OIM panel. HL2HL5 HL4HL3HL1 HL6ZX3G1X-OIM Fig. D.3-1    Location of Indicators on the OIM Panel Table D.3-3    Indicators on the OIM Panel Indicator Meaning HL1  3.3V power indicator. When it is on, it indicates that the 3.3V power is being supplied normally; when it is off, it indicates that the 3.3V power is not available.HL2  Tx clock lock indicator. When it is on, it indicates that the Tx clock has been locked; when it is off, it indicates that the Tx clock has not been locked yet. HL3 Data receiving preparation indicator. When it is on, it indicates that the receiving preparation has been completed; when it is off, it indicates that the receiving preparation has not been completed yet. HL4  Optical signal indicator. When it is on, it indicates that optical signals are available; when it is off, it indicates that no optical signals are available. HL5  5V power indicator. When it is on, it indicates that the 5V power is supplied normally; when it is off, it indicates that the 5V power is not available. HL6 Data receiving error indicator. When it is on, it indicates that errors exist in the currently received data; when it is off, it indicates that the currently received data is correct.
  E-1Appendix E Abbreviations Abbreviation Full Name 1X EV  1X Evolution 1X EV-DO  1X Evolution Data Only 1X EV-DV  1X Evolution Data & Voice 1X EV-DO  1X Evolution Data Optimized 24PB  24V Power Board 2G BTS  2G Base Transceiver Station 3G BTS  3G Base Transceiver Station   A AAA  Authentication Authorization Accounting AAL ATM Adaptation Layer AAL2  ATM Adaptation Layer type 2 AAL5  ATM Adaptation Layer type 5 Abis Interface  Abis Interface—the interface of BSC--BTS ABS  Air Break Switch AC Asynchronous Capsule ACB  Amplifier Control Board ACCH  Associated Control Channel ACCM  Asynchronous Control Character Map ACIR  Adjacent Channel Interference Ratio ACK Acknowledgement ACLR  Adjacent Channel Leakage Power Ratio ACS  Adjacent Channel Selectivity AGC  Automatic Gain Control AH Authentication Header AI Acquisition Indicator AICH  Acquisition Indicator Channel AID Application Identifier AIUR  Air Interface User Rate AK Anonymity key ALC  Automatic Level Control ALCAP  Access Link Control Application Protocol AM Acknowledged Mode AMB  Attenuation Matching Board
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-2Abbreviation Full Name AMF  Authentication Management Field AMP Address Management Protocol AMR  Adaptive Multi Rate AN Access Network ANID  Access Network Identifiers AP Access preamble APD  AC Power Distribution Module APDU  Application Protocol Data Unit API  Application Programming Interface ARM ARM processor ARP  Address Resolution Protocol ARQ  Automatic Repeat Request AS Access Stratum ASC  Access Service Class A-SGW  Access Signaling Gateway ASN.1  Abstract Syntax Notation One AT Access Terminal ATM Asynchronous Transfer Mode ATR Answer To Reset ATT Attenuator AUC Authentication Center AUTN Authentication token AWGN  Additive White Gaussian Noise A Interface  A Interface - the interface between BSC and MSC B B-BDS  Backplane of Baseband Digital Subsystem BBDS  Backplane of BDS BBS  BTS Baseband Subsystem BCC  Bear Channel Connect BCCH  Broadcast Control Channel BCFE  Broadcast Control Functional Entity BCH Broadcast Channel BCS  BTS Communication Subsystem BCSN  Backplane of Circuit Switch Network BCTC  Backplane of Control Center BDM  Baseband Digital Module BDM1900  1.9G Baseband Digital Module BDM800  800M Baseband Digital Module
 Appendix E  Abbreviations  E-3Abbreviation Full Name BDS  Baseband Digital System BER  Bit Error Ratio BGPS  Backplane of GPS BGT Block Guard Time BIM  BDS Interface Module B-ISDN Broadband ISDN BLPA  Backplane of LPA BMC Broadcast/Multicast Control BPD  BDS Power Distribute BPSK  Binary Phase Shift Keying BPSN  Backplane of Packet Switching Network BPWS  Backplane of PWS BRFE  Backplane of RFE BRFS  Backplane of TRX and BDM/RFM BS Base Station BSC  Base Station Controller BSM Base Station Management BSP  Board Support Package BSS  Base Station Subsystem BSSAP  Base Station Subsystem Application Part BTM BTS Test Module BTRX Backplane of TRX BTS Base Transceiver Station BUSN  Backplane of Universal Switching Network BWT  Block Waiting Time C CA Certificate Authentication CAMEL Customized Application for Mobile network Enhanced Logic CB Cell Broadcast CBR  Constant Bit Rate CBS  Cell Broadcast Service CC Control Channel CC/PP  Composite Capability/Preference Profiles CCCH  Common Control Channel CCF  Call Control Function CCH Control Channel CCK  Corporate Control Key CCM  Communication Control Module
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-4Abbreviation Full Name CCP  Compression Control Protocol CCPCH  Common Control Physical Channel CDF  Command Dispatch Functions CDMA  Code Division Multiple Access CDR  Call Detail Record CDSU  Channel/Data Service Unit CE Channel Element CEB  Channel Element Board CES  Channel Element Subsystem CFN  Connection Frame Number CGI  Common Gateway Interface CHAP Challenge Handshake Authentication Protocol CHM  Channel Processing Module CHM-1X  Channel Processing Module for CDMA2000 CHM-95  Channel Processing Module for IS-95 CIB  Circuit-bearer Interface Board CIC  Circuit Identification Code CLK Clock CLKD Clock Distributor CLKG Clock Generator CLNP Connectionless Network Protocol CLNS  Connectionless Network Service CM Configuration Management CMB Combiner CMF  Connection Monitor Function CMIP Common Management Information Protocol CMIS Common Management Information Service CMM  Capability Maturity Model CN Core Network CNAP  Calling Name Presentation CPCH  Common Packet Channel CPCS  Common Part Convergence Sublayer CPICH  Common Pilot Channel CPM  Calling Processing Module CPP  Core Processor Part CPU  Central Processing Unit CR Change Request CRC  Cyclic Redundancy Check
 Appendix E  Abbreviations  E-5Abbreviation Full Name CRF  Command Resolution Function CRNC  Controlling Radio Network Controller C-RNTI  Cell Radio Network Temporary Identity CS Circuit Switched CSCF  Call Server Control Function CS-GW  Circuit Switched Gateway CSM  Cell Site Modem CSM5000  Cell Site Modem ASIC 5000 CSU/DSU  Channel Service Unit/ Digital Service Unit CTCH Common Traffic Channel CTDMA  Code Time Division Multiple Access CTML  Common Trunking Message Link C-TPDU Command TPDU D D_K  DBS Kernel Module D_M D_Method D_S D_Service D_V D_View DAC Digital-to-Analog Converter DAD Destination Address DBS Database Subsystem DC  Dedicated Control (SAP) DCA Dynamic Channel Allocation DCCH  Dedicated Control Channel DCH Dedicated Channel DCM  Dispatching Client Module DCS  Dispatching Client Subsystem DDI  Direct Dial In DECT  Digital Enhanced Cordless Telecommunication DFSM  Dispatching Frame Selector Module DHCP  Dynamic Host Configuration Protocol DHO Diversity Handover DIF  Data Intermediate Frequency Module DIU  Digital Interface Module DL  Downlink (Forward Link) DLC  Data Link Control DN Destination Network DNS  Directory Name Service
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-6Abbreviation Full Name DO Data Object DOI  Domain of Interpretation DPC  Destination Point Code DPCCH  Dedicated Physical Control Channel DPCH  Dedicated Physical Channel DPDCH  Dedicated Physical Data Channel DRAC  Dynamic Resource Allocation Control DRC  Data Rate Control DRNC  Drift Radio Network Controller DRNS Drift RNS DRX Discontinuous Reception DSA Digital Signature Algorithm DS-CDMA  Direct Sequence-Code Division Multiple Access DSCH  Downlink Shared Channel DSM  Data Service Module DSS Dispatching SubSystem D-CN  Dispatching Control Node D-SN  Dispatching Serving Node DTB Digital Trunk Board DTCH Dedicated Traffic Channel DTI  Digital Trunk Interface Element DTMF  Dual Tone Multiple Frequency DTX Discontinuous Transmission DUP Duplexer E EDC  Error Detection Code byte EF Elementary File EHB  Ethernet HUB Board E-HLR Enhanced HLR EIRP  Equivalent Isotropic Radiated Power EJB  Enterprise Java Beans EMC Electromagnetic Compatibility EMI Electromagnetic Interference EMS Electromagnetic Susceptibility ESB  Ethernet Switch Board ESD Electrostatic discharge ESP  Encapsulating Security Payload ESU  Extended Subscriber Unit
 Appendix E  Abbreviations  E-7Abbreviation Full Name ETSI  European Telecommunications Standards Institute ETU Elementary Time Unit F F/R-CCCH  Forward / Reverse Common Control Channel F/R-DSCH Forward/Reverse Dedicated Signaling Channel F/R-DCCH  Forward / Reverse Dedicated Control Channel F/R-FCH  Forward / Reverse Fundamental Channel F/R-PICH  Forward / Reverse Pilot Channel F/R-SCCH  Forward / Reverse Supplemental Code Channel F/R-SCH  Forward / Reverse Supplemental Channel FA Foreign Agent FAC Foreign Agent Challenge FACH Forward Access Channel F-APICH  Forward-Dedicated Auxiliary Pilot Channel F-ATDPICH  Forward-Auxiliary Transmit Diversity Pilot Channel FAUSCH  Fast Uplink Signaling Channel FAX Facsimile F-BCCH  Broadcast Control Channel FBI Feedback Information F-CACH Forward-Common Assignment Channel FCI  File Control Information FCP  Flow Control Protocol F-CPCCH  Forward-Common Power Control Channel FCS  Frame Check Sequence FD Full Duplex FDD  Frequency Division Duplex FDMA  Frequency Division Multiple Access FE Front End FEC  Forward Error Correction FER  Frame Erasure Rate/Frame Error Rate Flexible-Rate  Flexible Data Rate FLPC  Forward Link Power Control FM Fault Management FN Frame Number FNUR  Fixed Network User Rate FP Function Point F-PCH Forward-Paging Channel F-QPCH  Forward-Quick Paging Channel
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-8Abbreviation Full Name FS Frequency Synthesizer FSB  Frequency Synthesizer Board F-SYNCH Forward-Synchronous Channel FTB Fiber Transceiver Board FTC Forward Traffic Channel F-TDPICH  Forward-Transmit Diversity Pilot Channel FTP File Transfer Protocol G GCM  GPS Control Module GID1  Group Identifier (level 1) GID2  Group Identifier (level 2) GMSC Gateway MSC GMSK  Gaussian Minimum Shift Keying GoTa Global open Trunking Architecture GP Guard Period GPCM  General Purpose Chip-select Machine GPRS  General Packet Radio Service GPS  Global Position System GPSR  Global Position System Receiver GPSTM GPS Timing Module GRE  Generic Routing Encapsulation GSM  Globe System of Mobile Communication GSN  GPRS Support Nodes GTP GPRS Tunneling Protocol H HA Home Agent HCS  Hierarchical Cell Structure HDLC  High-level Data Link Control HDR  High Data Rate HHO Hard Handover HIRS  High-speed Interconnect Router Subsystem HLR  Home Location Register HN Home Network HO Handover HPA High Power Amplifier HPS  Handover Path Switching HRPD  High Rate Packet Data HRR  Handover Resource Reservation
 Appendix E  Abbreviations  E-9Abbreviation Full Name HSCSD  High Speed Circuit Switched Data HSS  Home Subscriber Server HWB  HW-signal process Board I I/O Input/Output I-Block Information Block IC Intergroup Coordination ICC  Integrated Circuit Card ICGW  Incoming Call Gateway ID Identifier IEC  International Electrical Commission IETF  Internet Engineering Task Force IF Intermediate Frequency IFS  Information Field Sizes IFSC  Information Field Size for the UICC IFSD  Information Field Size for the Terminal IIC  Integrated Circuit Interface Circuit IKE  Internet Key Exchange IM Intermodulation IMA  Inverse Multiplexing on ATM IMAB IMA Board IMEI  International Mobile Equipment Identity IMGI  International mobile group identity IMSI  International Mobile Subscriber Identity IMT-2000  International Mobile Telecommunications 2000 IMUN  International Mobile User Number IN Intelligent Network INAP  Intelligent Network Application Part INF Information Field IP Internet Protocol IPB  IP Process Board IPCP  IP Control Protocol IP-M IP-Multicast IPSec IP Security ISAKMP Internet Security Association and Key Management Protocol ISCP  Interference Signal Code Power ISDN  Integrated Services Digital Network ISO International Standardization Organization
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-10Abbreviation Full Name ISP  Internet Service Provider ISUP  ISDN User Part ITU International Telecommunications Union IUI  International USIM Identifier IWFB  InterWorking Function Board J J2EE  Java 2 Platform Enterprise Edition JAR file  Java Archive File JD Joint Detection JDMK Java Dynamic Management Kit JMS  Java Message Service JNDI  Java Naming Directory Interface JP Joint Predistortion JTAPI  Java Telephony Application Programming Interface JTS Java Transaction Service JVM Java Virtual Machine K kbps  kilo-bits per second ksps  kilo-symbols per second L L1  Layer 1 (physical layer) L2  Layer 2 (data link layer) L3  Layer 3 (network layer) L3Addr Layer 3 Address LAC Link Access Control LAI Location Area Identity LAN Local Area Network LATA  Local Access and Transport Area LCD  Low Constrained Delay   LCF  Link Control Function LCP  Link Control Protocol LCS Location Services LFM  Local Fibre Module LLC  Logical Link Control LMF  Local Management Function LMT Local Management Terminal LN Logical Name LNA Low Noise Amplifier
 Appendix E  Abbreviations  E-11Abbreviation Full Name LOMC Local OMC LPA Linear Power Amplifier LPF  Low Pass Filter LSB  Least Significant Bit   M M&C  Monitor and Control MA Multiple Access MAC Message Authentication Code (encryption context) MAF Management Application Features MAHO Mobile Assisted Handover MAP Mobile Application Part MCC  Mobile Country Code MCE  Module Control Element Mcps  Mega-chips per second MCU  Media Control Unit MDIV Micro Diversity MDIV800  800M Micro Diversity   MDN  Mobile Directory Number MDS  Multimedia Distribution Service MDUP Micro Duplex MDUP800  800M Micro Duplex   ME Mobile Equipment  MEHO  Mobile Evaluated Handover MER  Message Error Rate MF Mediation Function MGCF  Media Gateway Control Function MGCP  Media Gateway Control Part MGPS Micro GPS MGW Media GateWay MHEG  Multimedia and Hypermedia Information Coding Expert Group MHz Mega Hertz MIB Management Information Base MIF Management Information Function MIN  Mobile Identification Number MIP Mobil IP MIPS  Million Instructions Per Second MIT MO Instance Tree MLNA  Micro Low Noise Amplifier
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-12Abbreviation Full Name MLNA800  800M Micro Low Noise Amplifier   MM Mobility Management MMI  Man Machine Interface MML  Man Machine Language MNC  Mobile Network Code MNIC  Multi-service Network Interface Card MNP  Mobile Number Portability MO Mobile Originated MOF  MO administration Function MOHO  Mobile Originated Handover MONB Monitor Board MOS  Mean Opinion Score MPA Micro Power Amplifier MPA800  800M Micro Power Amplifier   MPB  Main Process Board MPC8260  Motorola Power PC 8260 MPC860  Motorola Power PC 860 MPD  Micro-BTS Power Distribution MPM  MSC Processing Module MRB  Media Resource Board MRF  Media Resource Function MS Mobile Station MSB  Most Significant Bit MSC  Mobile Switching Center MSG  Management Steering Group MSID  Mobile Station Identifier MSIN  Mobile Station Identification Number MSM  Message Switching Module MSP  Multiple Subscriber Profile MSU  Main Subscriber Unit MT Mobile Termination MTBF  Mean Time Between Failures MTP Message Transfer Part MTP3-B  Message Transfer Part level 3 MTRX800  800M Micro Transmitter & Receiver   MTSI  Master To Slave Interface MUI  Mobile User Identifier   N
 Appendix E  Abbreviations  E-13Abbreviation Full Name NAD Node Address byte NAI Network Access Identifier NAS Non-Access Stratum NBAP  Node B Application Part   NCK  Network Control Key NCM  Network Control Module NDC  National Destination Code NDUB  Network Determined User Busy   NE Network Element NEF  Network Element Function NEHO  Network Evaluated Handover NEMF  Network Element Mediation Function NIM  Network Interface Module NITZ  Network Identity and Time Zone NMC  Network Management Center NMSI  National Mobile Station Identifier NNI Network-Node Interface NO Network Operator NP Network Performance NPA Numbering Plan Area NPI  Numbering Plan Identifier NRT Non-Real Time  NSAP  Network Service Access Point NSCK  Network Subset Control Key NSDU  Network Service Data Unit NSS Network Subsystem NW Network O O&M  Operations and Maintenance O_AMP O&M _Alarm Management Part O_CMP O&M _Configuration Management Part O_PMP O&M _Performance Management Part O_RMP O&M _Right Management Part O_TMP  O&M _Test Management Part OCCCH  ODMA Common Control Channel ODCCH  ODMA Dedicated Control Channel ODCH  ODMA Dedicated Channel ODMA  Opportunity Driven Multiple Access
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-14Abbreviation Full Name ODTCH  ODMA Dedicated Traffic Channel OIB  Optical Interface Board OIM  Optical Interface Module OMC  Operation Maintenance Centre OMF  Operation Maintenance Function OMI  Operation Maintenance Interface OMM  Operation Maintenance Module OMS  Operation & Maintenance Subsystem OO Object-Oriented OOF  Operation Outputting Function OPD  Organization Process Definition OPF  Organization Process Focus OPRM  Optical Receiver Module OPTM Optical Transmitter Module OSA Open Service Architecture OSF  Operations Systems Function OSS  Operating Systems Subsystem OSS_CLP  OSS_Communicating Link Part OSS_FMP  OSS_File Management Part OSS_RSP  OSS_Running Support Part OSS_SCP  OSS_Status Control Part OSS_SWD OSS_Software Download OVSF  Orthogonal Variable Spreading Factor OWB Order Wire Board P PA Power Amplifier PAB Power Amplify Board PACA  Priority Access and Channel Assignment PAM Power Alarm Module PAP Password Authentication Protocol PBP  Paging Block Periodicity PC Power Control PCB  Protocol Control Byte PCCC  Parallel Concatenated Convolution Code   PCCH  Paging Control Channel PCCPCH  Primary Common Control Physical Channel PCF  Packet Control Function PCH Paging Channel
 Appendix E  Abbreviations  E-15Abbreviation Full Name PCMCIA  Personal Computer Memory Card International Association PCP  Packet Consolidation Protocol PCPCH  Physical Common Packet Channel PCS  Personal Communication System PCU  Packet Control Unit PD Power Divider PDB Process Database PDC  PTT Dispatching Client PDCP  Packet Data Convergence Protocol PDF  Detecting of Power Direction Forward PDN  Public Data Network PDP  Packet Data Protocol PDR  Detecting of Power Direction Reverse PDS  PTT Dispatching Server PDSCH  Physical Downlink Shared Channel PDSN  Packet Data Serving Node PDU  Protocol Data Unit PERT  Program Evaluation and Review Technique PG Processing Gain PHB  Per Hop Behavior PHR  PTT Home Register PHS  Personal Handy phone System PHY Physical layer PhyCH Physical Channel PI Page Indicator PICH Pilot Channel PID Packet Identification PIM  Power Amplifier Interface Module PIN  Personal Identifying Number PL Physical Layer PLMN  Public Land Mobile Network PM Project Manager PMD  Physical Layer Medium Dependent PMM  Power Monitor Module PN Pseudo Noise PNP  Private Numbering Plan POMC Province OMC POTS  Plain Old Telephone Service
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-16Abbreviation Full Name PP2S    PPM  Protocol Process Module PPP Point-to-Point Protocol PPS  Protocol and Parameter Select (response to the ATR) PR Peer Reviews PRACH  Physical Random Access Channel PRE Pre-amplifying Board PRM  Power Rectifier Module PS Packet Switched PSB  Power Splitter Board PSC  Primary Synchronization Code   PSCH  Physical Shared Channel PSE  Personal Service Environment PSI  PCF Session ID PSM  Power Supplier Module PSN  Packet Switched Network PSOS    PSPDN  Public Switched Packet Data Network PSTN  Public Switched Telephone Network PTM Power Transition Module PTM-G  PTM Group Call PTM-M PTM Multicast PTP  Point to point PTT Push to Talk PUSCH  Physical Uplink Shared Channel PVD  Power VSWR Detect Board PWRD POWER Distributor PWS Power System Q QA Quality Assurance QAF Q3 Adaptor Function QC Quality Control QoS  Quality of Service QPM  Quantitative Process Management QPSK  Quadrature Phase Shift Keying QXF  Qx Interface Function R R_CLP  R_Communication Link Part
 Appendix E  Abbreviations  E-17Abbreviation Full Name R_CLP_InSubsystem    R_CLP_InterSubsystem    R_CLP_MasterSlave    R_CLP_TrafficData    R_FMP  R_File Management Part R_FMP_Background    R_FMP_Foreground    R_RSP  R_Running Support Part R_RSP_AbnormityProcess    R_RSP_MemoryManagement    R_RSP_ProcessCommunication    R_RSP_ProcessDispatch     R_RSP_StartupConfigration    R_RSP_SystemObservation    R_RSP_Timer Management    R_SCP  R_System Control Part R_SCP_Boot    R_SCP_MainControl    R_SCP_StatusControlManagement   RA Routing Area RAB Reverse Activity Bit RAC Reverse Access Channel R-ACH Access Channel RACH Random Access Channel RADIUS  Remote Authentication Dial-In User Service RAI Routing Area Identity RAN Radio Access Network RANAP Radio Access Network Application Part   RB Radio Bearer R-Block Receive-ready Block RC Radio Configuration RDF  Resource Description Format R-EACH Enhanced Access Channel RF Radio Frequency RFCM  RF Control Module RFE  Routing Functional Identity RFF RF Filter RFIM  RF Interface Module
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-18Abbreviation Full Name RFM  Remote Fiber Module RFM1900  1.9G Remote Fiber Module RFM800  800M Remote Fiber Module RFS  Radio Frequency Subsystem RIM  RF Interface Module RL Radio Link RLC  Radio Link Control   RLCP  Radio Link Control Protocol RLP  Radio Link Protocol RMI  Remote Method Invocation RMM  RF Management Module RN Radio Network RNC  Radio Network Controller   RNS  Radio Network Subsystem   RNSAP  Radio Network Subsystem Application Part   RNTI  Radio Network Temporary Identity ROI  Return On Investment RPB  Router Protocol Process Board RPC  Reverse Power Control RPD  RFS Power Distribute RPT Repeater RRC  Radio Resource Control RRI  Reverse Rate Indication RRM  Radio Resource Management RRP  Mobile IP Registration Reply RRQ  Mobile IP Registration Request RSA Rivest-Shamir-Adleman public key algorithm RSCP  Received Signal Code Power R-SGW  Roaming Signaling Gateway RSM  Reverse Switch Module RSSI  Received Signal Strength Indicator RST Reset RSVP  Resource Reservation Protocol RT Real Time RTC Reverse Traffic Channel RTOS  Real Time Operate System RTP Real Time Protocol R-TPDU Response TPDU
 Appendix E  Abbreviations  E-19Abbreviation Full Name RU Resource Unit RUM  Route Update Message RUP  Route Update Protocol RX Receiver RXB Receiver Board S S/N Signal/Noise S_BSSAP  SPS Base Station System Application Part S_CCHSP  SPS Control Channel Signaling Process S_CEC  SPS Channel Element Controller S_CEM  SPS Channel Element Modem S_MTP  SPS Message Transfer Part S_MTP3  SPS Message Transfer Part3 S_RCM  SPS Radio Channel Control Management S_SCCP  SPS Signaling Connection Control Part S_SVLP  SPS Selector Vocoder Low-Layer Process S_TCHL2P  SPS Traffic Channel Layer2 Process S_TCHL3P  SPS Traffic Channel Layer3 Process S_TLH  SPS Traffic Link Handler S_VIM  SPS Vocoder Interface Module SA Security Association SAAL  Signaling ATM Adaptation Layer SACCH  Slow Associated Control Channel SAD Source Address SAM Site Alarm Module SAP Service Access Point SAPI  Service Access Point Identifier SAR  Segmentation and Reassembly SB Storage Battery S-Block Supervisory Block SC Synchronous Capsule SCC  Serial Communication Controller SCCB  Software Configuration Control Board SCCH  Synchronization Control Channel SCCP  Signaling Connection Control Part SCCPCH  Secondary Common Control Physical Channel SCE  Software Capability Evaluation SCH Synchronization Channel
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-20Abbreviation Full Name SCI  Subscriber Controlled Input SCM  Sub-BDS Control Module SCP Session Configuration Protocol SCS  System Control Subsystem SCWLL  Super CDMA Wireless Local Loop SDCCH  Stand-Alone Dedicated Control Channel SDF  Service Discovery Function SDH  Synchronous Digital Hierarchy SDHB SDH Board SDL  Specification & Description Language SDP  Software Development Plan SDTB  Sonet Digital Trunk Board SDU  Service Data Unit SF Spreading Factor SHA Secure Hash Algorithm SHCCH  Shared Control Channel SIE  Sector Interface Element SIM  GSM Subscriber Identity Module SINR  Signal-to-Interface plus Noise ratio SIP  Session Initiated Protocol SIR Signal-to-Interference Ratio SLA Service Level Agreement SLP  Signaling Link Protocol SMC  Serial Management Controller SME  Short Message Entity SMF Session Management Function SMP Session Management Protocol SMS  Short Message Service SMS-CB  SMS Cell Broadcast SN Serving Network SNM  Switching Network Module SNP  Signaling Network protocol SPB  Signaling Process Board SPLL  System Phase Locked Loop SPS  Signaling Process Subsystem SQN Sequence Number SR1  Spreading Rate 1 SS7  Signaling System No.7
 Appendix E  Abbreviations  E-21Abbreviation Full Name STC Signaling Transport Converter STDL  Shared Trunking Data Link STTD  Space Time Transmit Diversity SVBS  Selector & Vocoder Bank Subsystem SVC  Switched virtual circuit SVE  Selector & Vocoder Element SVICM  Selector & Vocoder Interface Control Module SVM  Selector & Vocoder Module SVP  Selector & Vocoder  Processor SVPM  Selector & Vocoder & PCF Module SVPP  Selector & Vocoder & PCF Processor T TCH Traffic Channel TCM  Technology Change Management TCP  Transmission Control Protocol TCP/IP    TD-CDMA  Time Division-Code Division Multiple Access TDD  Time Division Duplex TDMA  Time Division Multiple Access TE Terminal Equipment TFM  Timing Frequency Module TFS  Timing & Frequency Subsystem TLLI  Temporary Link Level Identity TLS  Transport Layer Security TMB  Traffic Manage Board TMN Telecommunication Management Network TMSI  Temporary Mobile Subscriber Identity TN Termination Node TOD  Time of Date TPC  Transmit Power Control TPDU  Transfer Protocol Data Unit TPTL  Transmission Power Track Loop TrCH Transport Channel TRX  Transmitter and Receiver T-SGW  Transport Signaling Gateway TSM  Transmit Switch Module TSNB  TDM Switch Network Board TSTD  Time Switched Transmit Diversity
ZXCBTS (V5.4) CDMA Micro Base Transceiver Station & Remote Station Installation Manual    E-22Abbreviation Full Name TTI Transmission Timing Interval TX Transmitter TXB Transmitter Board U UDP  User Datagram Protocol UDR  User Data Record UE User Equipment UI User Interface UICC  Universal Integrated Circuit Card UIM  Universal Interface  Module UL  Uplink (Reverse Link) ULB  Universal LED Board UM Unacknowledged Mode UMS  User Mobility Server UMTS  Universal Mobile Telecommunications System Um Interface  Um Interface-the interface between MS and BTS UNI User-Network Interface UPT Universal Personal Telecommunication URI  Uniform Resource Identifier URL  Uniform Resource Locator USCH  Uplink Shared Channel UT Universal Time UTRA Universal Terrestrial Radio Access UTRAN  Universal Terrestrial Radio Access Network   V VA Voice Activity factor Variable-Rate  Variable Data Rate VASP  Value Added Service Provider VBR  Variable Bit Rate VBS  Voice Broadcast Service VC Virtual Circuit VCO  Voltage Control Oscillator VGCS  Voice Group Call Service VHE  Virtual Home Environment VLR  Visitor Location Register VMS  Voice Mail Server VoIP  Voice Over IP VPLMN  Visited Public Land Mobile Network
 Appendix E  Abbreviations  E-23Abbreviation Full Name VPM  VLR Processing Module VPN  Virtual Private Network VSWR  Voltage Standing Wave Ratio VTC Voice Transcoder Card W WAE Wireless Application Environment WAP Wireless Application Protocol WCDMA  Wideband Code Division Multiple Access WCF  Workstation Control Function WDP  Wireless Datagram Protocol WIN  Wireless Intelligent Network WPB  Wireless Protocol Process Board WSF Workstation Function WSP Wireless Session Protocol WTA Wireless Telephony Applications WTAI Wireless Telephony Applications Interface WTLS  Wireless Transport Layer Security WTP Wireless Transaction Protocol  X XRES  Expected user Response Z ZXCBTS M800T  ZTE CDMA 800M micro base station (10W) ZXCBTS M802T  ZTE CDMA 800M micro base station (20W)  ZXCBTS M190T  ZTE CDMA 1900M micro base station (5W) ZXCBTS M191T  ZTE CDMA 1900M micro base station (10W) ZXCBTS M192T  ZTE CDMA 1900M micro base station (20W) ZXCBTS R800T  ZTE CDMA 800M RF remote base station (10W) ZXCBTS R802T  ZTE CDMA 800M RF remote base station (20W) ZXCBTS R190T  ZTE CDMA 1900M RF remote base station (5W) ZXCBTS R191T  ZTE CDMA 1900M RF remote base station (10W) ZXCBTS R192T  ZTE CDMA 1900M RF remote base station (20W)

Navigation menu