user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1739006 |
| Application ID | YIeSrsgR3ys5gsOT5/FSKQ== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 197.29kB (2466183 bits) |
| Date Submitted | 2012-07-09 00:00:00 |
| Date Available | 2012-07-11 00:00:00 |
| Creation Date | 2017-10-31 00:45:48 |
| Producing Software | GPL Ghostscript 9.18 |
| Document Lastmod | 2017-10-31 00:45:48 |
| Document Title | Microsoft Word - ZXHN H368C QSG_v1-00_ed1_2012-06-22.docx |
| Document Creator | PScript5.dll Version 5.2.2 |
| Document Author: | MT01165 |
ZTE CORPORATION NO. 55, Hi-tech Road South, ShenZhen, P.R.China Postcode: 518057 Tel: (86) 755 26771900 Fax: (86) 755 26770801 URL: http://ensupport.zte.com.cn E-mail: support@zte.com.cn ZXHN H368C ZXHN H368C User’s Manual Document version: 2012-06-22 R1.0 Copyright 2012 ZTE Corporation All rights reserved. No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated, in any form or by any means without the prior written permission of ZTE Corporation. ZTE CORPORATION reserves the right to modify this manual for product upgrade or other causes without notifying users in advance. Limited warranty ZTE warrants that, for one year from the date of delivery by ZTE to purchaser's designated carrier, the Equipment will remain free from defects in design, material and workmanship under normal use and service and will conform in all material respects to the applicable specifications set forth in purchase order or agreement; ZTE does not warrant that operation of the Equipment will be error-free or uninterrupted. In accordance with ZTE's standard, warranty terms, ZTE shall, at its option, repair or replace any defective or nonconforming item, provided that (a) purchaser/End User gives ZTE written notice of the defect or nonconformity within the warranty period specified above promptly after Reseller is notified by the End User of the same; and (b) End User returns the defective item at its expense to ZTE’s nominated Customer Service Department in accordance with ZTE’s standard parts exchange procedures. This warranty does not apply to defects or errors in the Equipment caused by:(a) reasonable abrasion of equipments; (b)End User’s failure to follow ZTE’s installation, operation or maintenance instructions or procedures; (c) End User’s mishandling, misuse, negligence, or improper installation, deinstallation, storage, servicing or operation of the Equipment; (d) modifications or repairs not made by ZTE or a ZTE-certified individual;(e) power failures, surges, fire, flood, accident, actions of third parties or other events outside ZTE’s reasonable control. (f) usage of products of third Parties, or usage conjunction with third parties provided that such defects is due to the conjunction;(g) any other cause beyond the range of normal usage for equipments. End User shall assure that Equipment is installed and maintained by ZTE or ZXHN H368C User’s Manual ZTE-certified individuals in accordance with ZTE’s certification procedures; provided that if End User causes or permits services to be provided by individuals who are not ZTE-certified, the Warranty shall be void as to all Equipment serviced in breach of this sentence. End User shall have no right to reject, return, or receive a refund for any Equipment from ZTE. Any item repaired or replaced by ZTE shall continue to be warranted for the longer of the remainder of the original warranty period or 90 days from the date the repaired or replaced part is delivered to the carrier. THIS WARRANTY (1) IS END USER'S SOLE REMEDY AND ZTE’S SOLE LIABILITY FOR DEFECTIVE OR NONCONFORMING ITEMS , AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, UNLESS OTHERWISE REQUIRED UNDER THE MANDATORY PROVISIONS OF THE CHINESE LAW, AND (2) IS BETWEEN ZTE AND END USER (AS THE ORIGINAL PURCHASER FOR END USE) AND MAY NOT BE TRANSFERRED OR ASSIGNED, BY OPERATION OF LAW OR OTHERWISE, WITHOUT ZTE’S PRIOR WRITTEN CONSENT. Limitation of Liability ZTE SHALL NOT BE LIABLE FOR ANY LOSS OF PROFITS OR INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM OR ARISING OUT OF OR IN CONNECTION WITH USING OF THIS PRODUCT, WHETHER OR NOT ZTE HAD BEEN ADVISED, KNEW OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, COST OF CAPITAL, COST OF SUBSTITUTE FACILITIES OR EQUIPMENT, ANY DOWNTIME COSTS OR CLAIMS ii ZXHN H368C User’s Manual OF END USERS. THE LIABILITY OF EACH PARTY UNDER THIS AGREEMENT, WHETHER ARISING OUT OF BREACH OF CONTRACT (INCLUDING BUT NOT LIMITED TO BREACH OF WARRANTY) OR TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE AND STRICT LIABILITY) OR UNDER AN INDEMNIFICATION PROVISION SHALL IN NO EVENT EXCEED THE AGGREGATE AMOUNT BENIFITED BY ZTE IN THE PRODUCTS FROM WHICH SUCH LOSS OR DAMAGE DIRECTLY AROSE. Confidentiality End User agrees that End User will receive confidential or proprietary information (“Confidential Information”) in connection with the purchase and deployment of ZTE Equipment. End User will not disclose ZTE’s Confidential Information, will use it only for purposes for which it was disclosed, and must treat it with the same degree of care as it does its own similar information, but with no less than reasonable care. End User agrees that the terms herein, the Equipment and all ZTE documentation is ZTE Confidential Information. iii Contents Chapter 1 Safety Guidance ............................................................1 1.1 Safety Check ......................................................................................... 1 1.2 Safety Cautions ..................................................................................... 1 Chapter 2 Overview .......................................................................3 2.1 Features................................................................................................. 3 2.2 Product Specifications .......................................................................... 3 2.3 Package Check ...................................................................................... 4 2.4 System Requirement ............................................................................. 5 Chapter 3 Installation Preparation ...............................................6 3.1 Hardware Description ........................................................................... 6 3.2 Hardware Connection ........................................................................... 9 Appendix A FAQs .........................................................................12 Chapter 1 Safety Guidance 1.1 Safety Check Before installing the VDSL2 equipment, check all the below listed items: 1 Electric safety Ensure no inflammable, conductive or moist objects and no ageing-cables around the equipment. Place all electrical appliances safely. 2 Equipment position Install the equipment in a ventilated environment avoid of any electric devices nearby. Place the equipment on a stable and flat surface. The equipment must be protected from sunshine. It must be kept away from electro-magnet interference. The equipment must be protected from heat and water sources. Ensure the power supply is available. The fluctuation range of input voltage should be in the range of ±10%. Do not share the power socket with other electrical devices. 1.2 Safety Cautions Please pay attention to the following cautions: Read the user’s manual carefully before using the equipment. Note all Cautions in the user’s manual and product guide. Do not use any accessory or components that are not belonging to the equipment. ZXHN H368C User’s Manual Use the power adapter, which is provided in the package. Connect the phone with the VDSL2 line directly, and lead the line out from the phone interface of the splitter. Do not place any object on the equipment. The equipment must be kept dry and clean. Ensure the equipment environment has ventilation and rainproof capability. To protect the equipment against lightning and thunderstorm, please remove the power plug and all connection cables. Use a soft and dry cloth to clean the equipment. Ensure the equipment is power OFF before cleaning. Power OFF the idle equipment. Keep the ventilation-hole clean and unblocked. Otherwise, it may cause short circuit, fire or damage the equipment. Do not spray liquid on the equipment surface. Do not open the equipment especially in power ON state. Confirm the power is OFF before plugging/unplugging the power. Keep all components and accessories of the equipment away from the children. Note: Please read the above safety guidance carefully before equipment use. Users should assume responsibilities for any accidents due to incompliance with the above instructions. Chapter 2 Overview The ZXHN H368C is a VDSL gateway, which provides high-speed VDSL Internet access. It is designed with triple WAN function: VDSL, ADSL, and Gigabyte WAN. The ZXHN H368C also features a built-in 802.11n WLAN and an embedded MoCA for multimedia over coaxial cable. In addition, the ZXHN H368C has a USB interface for file sharing and printer server. 2.1 Features The ZXHN H368C is a VDSL2 MODEM. It supports the following features: ITU-T G.993.2 VDSL2 standard and ITU-T G.992.5 DSL2+ standard. It supports WLAN with high-speed data transfer rates up to 300 Mbps, compatible with IEEE 802.11b/g/n, 2.4 GHz compliant equipment. It supports IEEE802.3 and IEEE802.3u. It supports speed auto-negotiation. It supports Half duplex/Full duplex. It supports user-friendly GUI for web configuration. It supports IPSec for virtual private network (VPN). It supports parental control function to restrict children usage. It supports self-learning bridge (IEEE 802.1D Transparent Bridging). It supports virtual server, IP filter, and demilitarized military zone (DMZ) host. It supports USB 2.0 host. 2.2 Product Specifications Environmental requirements ZXHN H368C User’s Manual Environmental temperature: -5°C-45°C (23 °F-113°F) Humidity: 5% - 95% (non-condensing) Power specification Power adapter: Input: AC 100-240V, 50/60 Hz Output: DC 12V, 1.5A Certification FCC UL WiFi 2.3 Package Check ZXHN H368C 1 Micro Filter 1 Power Adapter 1 RJ-11 telephone cable 2 RJ-45 Ethernet cable 1 User’s Manual & Quality Warranty Card 1 Certificate of Quality 1 Note: for your information only, please refer to the actual product. Caution: to reduce the risk of fire, use only NO.26AWG or larger (e.g., 24AWG) UL Listed or CSA Certified Telecommunication Line Cord. Note: Please use a power adapter that matches the ZXHN H368C package. ZXHN H368C User’s Manual 2.4 System Requirement Before installing the ZXHN H368C, please check the following items. 1 VDSL Services Subscription If you have subscribed for the VDSL service, your VDSL operator must provide at least one valid IP address for you (static allocation or dialup dynamic allocation). 2 Computer configuration Please make sure that the system has been equipped with the 10M/100M Ethernet adapter and supports the TCP/IP protocol. Because VDSL can be used for broadband access and involves a wide range of multimedia services, you are recommended use a computer with such configurations as: above Pentium III, 64M memory, 10G hard disk, graphic accelerating adapter with above 2M display memory, audio adapter and sound box. 3 Operating system Operating systems can be Windows 98SE, Windows Me, Windows 2000, Windows XP, Windows Vista or Windows 7. For system configuration in the WEB interface, the browser of Internet Explorer V 6.0 or later. Chapter 3 Installation Preparation 3.1 Hardware Description Front panel Figure 3.1-1 Front Panel of the ZXHN H368C ZXHN H368C User’s Manual Table 3.1-1 Descriptions of the LEDs on the Front Panel Function Power MoCA Color Status Definition OFF Power OFF. Power ON, HW Test failure or Green/Red Red device malfunction. Green Power ON, HW Test ok. Power OFF, no MoCA network OFF connection to the MODEM. Green Flash The MODEM has LAN activity. The MODEM has proper MoCA ON network link. Power is off or the modem is not OFF connected to any USB device. USB Green GWAN Green LAN1-LAN4 Green WLAN Green WPS Green Green Data is transmitted on the USB port. Flash The modem is connected to a USB Green device. The Gigabyte Ethernet WAN link is OFF not connected. The Gigabyte Ethernet WAN Flash interface is receiving or sending data. The Gigabyte Ethernet WAN link ON up. The Ethernet port is in the OFF non-communication state. The Ethernet port is in the ON communication state. Ethernet interface is receiving or Flash sending data. OFF No detected radio signal. WLAN port is receiving or sending Flash data. WLAN interface is ready to work. ON OFF WPS function is OFF. ZXHN H368C User’s Manual Function Color DSL Green Internet Green Status Definition WPS function is in negotiation Flash status. ON WPS function is ON. The MODEM is in the OFF non-communication state. The MODEM is in training state. Flash The MODEM is in the ON communication state. OFF No detected data. WAN port is receiving or sending Flash data. WAN port is in communication ON status. Rear panel Figure 3.1-2 Rear Panel of the ZXHN H368C Table 3.1-2 Description of Interfaces on the Rear Panel Interface DSL LAN1-LAN4 GWAN USB WIFI ON/OFF Function RJ-11port: Using the telephone line to connect the modem with the VDSL2 cable or splitter. RJ-45 port: It is used to connect the modem to other network devices. RJ-45 port: It is used to connect the modem to computer or other network devices. USB interface: connects to a USB device. WIFI button: to enable or disable the WLAN function. ZXHN H368C User’s Manual 3.2 Hardware Connection Figure 3.2-1 ZXHN H368C Connection Schematic Diagram ZXHN H368C User’s Manual Connection procedures 1 Power off the equipment before all the other devices are connected. 2 Connect the network cables: Insert the RJ-45 Ethernet cable connector into the Ethernet interface of the ZXHN H368C, and connect its other terminal to the Ethernet adapter of the customer computers or ports of other network devices. 3 Connect the splitter The splitter has three interfaces, which are described as follows: LINE: Connect the user telephone cable (RJ11 interface). MODEM (or DSL): Connect the DSL interface of the ZXHN H368C. PHONE (or TEL): Connect the phone sets. The installation process is as follows: Connect the LINE interface of the ZXHN H368C to the MODEM(or DSL) interface of the splitter using the RJ-11 telephone cable, connect the phone set lines to the PHONE(or TEL) interface of the splitter, and then connect the user telephone cable port to the LINE interface of the splitter. 4 Connect the MoCA port to a Set-Top box with a coaxial cable for multimedia. 5 Connect the power Connect one terminal of the power adapter to the POWER interface of the ZXHN H368C, and the other terminal to the socket on the wall, and then switch on the power of the ZXHN H368C equipment. Checking all connection cables Check all connection cables following the below procedure. 1 Check the DSL cable connection If the DSL LED is on upon power-on of the ZXHN H368C, it indicates that the DSL line is correctly connected (Generally it takes one to two minutes to perform the DSL connection). 2 Check the computer connection 10 ZXHN H368C User’s Manual If both the LINK LED on the computer adapter and the Ethernet LED of the ZXHN H368C turn green, it indicates that the computer and the ZXHN H368C equipment are correctly connected. 3 Check the telephone cable connection 11 Appendix A FAQs No. Problem and Troubleshooting All indicators are OFF when the ZXHN H368C equipment is powered ON. First make sure that you have inserted the power adapter of the ZXHN H368C into a working power socket and that the ZXHN H368C has been powered ON (the power button is pressed in). If the indicators are still OFF after confirmation of the above items, may be the hardware is damaged. You may contact local operators for maintenance. Never dismantle the equipment by yourself. Will VDSL2 affect the telephone conversation quality? Will making phone calls cause a slow online rate? VDSL2 separates voices from data through the frequency division multiplexing technology. Therefore, voices and data run in different paths without mutual interference. Neither the access rate nor conversation quality will fall even if you are in a call and online simultaneously. How to properly install telephone extensions or other devices on the VDSL2 line? It is recommended to connect the VDSL2 splitter to the telephone cable first and then connect the phone sets to the splitter interfaces. Installing a telephone directly before the splitter will lead to connection failure between the ZXHN H368C and the device at central office side, or an Internet access failure, or a slow connection speed. Connecting other electronic devices between the user end and splitter may affect the VDSL2 communications (since VDSL2 has a higher requirement for the line quality) and furthermore affect the normal operation of VDSL2. If the phone sets are required to be connected before the splitter, you should serially connect the MicroFilter before the phone sets (Generally, to minimize interference, only one MicroFilter can be connected before the splitter). Sometimes, the VDSL2 users cannot access to the Internet normally 12 ZXHN H368C User’s Manual No. Problem and Troubleshooting First check whether the ZXHN H368C is in the normal state (Check the indicators according to this user’s manual). If yes, the computer or application network may be faulty. This is unrelated with VDSL2. If the VDSL2 MODEM is abnormal, check the status of indicators one by one to remove the fault. It is suggested to check the following items before seeking help from operators: 1. The VDSL2 telephone cable connectors are proper. 2. The VDSL2 is away from the power cable and large-power electronic devices. 3. No telephone extensions and fax machines are connected between the VDSL2 incoming line and splitter. 4. The splitter has been installed correctly. 5. The VDSL2 MODEM has good heat dissipation ratio. What are reasons for VDSL2 synchronization failure (also referred as link down or link establishment failure)? 13 ZXHN H368C User’s Manual No. Problem and Troubleshooting If the VDSL2 suddenly fails to be synchronized (link down) during application, usually the Link indicator on the MODEM will not be ON. It is suggested to check the following steps one by one: 1. First check the quality of incoming cables and incoming cable connectors. 2. Install the VDSL2 MODEM correctly based on the user guidance. Minimize the number of taps. 3. Check whether the telephone cables and VDSL2 are in good connection or whether the telephone cables are normal. 4. Try to disconnect the splitter and directly connect the VDSL2 MODEM to the incoming user cable end. Ensure the problem is not due to improper installation or incoming user line quality. If the VDSL2 can be synchronized again, it means that installation of the incoming user side is improper. Please reinstall it according to the user guide. 5. If the VDSL2 still fails to be synchronized when the VDSL2 MODEM is connected to the incoming user cable end, contact the operators to check whether it is due to external line failure or MODEM failure. 6. If the splitter problem is determined, call the operator for maintenance or replacement. 7. If the problem is due to the end office equipment failure, call the operator to confirm it. 8. Too long connection cable between the splitter and VDSL2 MODEM may cause poor anti-interference performance and synchronization difficulty. Therefore, the connection cable should not be too long. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 14 ZXHN H368C User’s Manual This equipment complies with FCC radiation exposure limits set forth for uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 15 ZXHN H368C User’s Manual Customer Information 1. This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On bottom of this equipment is a label that contains, among other information, product identifier of US: ZTEDL01BHNH368CV1. If requested, this number must be provided to the telephone company. 2. If this equipment VDSL CPE causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary. 3. The telephone company may make changes in this facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modification to maintain uninterrupted service. 4. If you experience trouble with this equipment, you disconnect it from the network until the problem has been corrected or until you are sure that the equipment is not malfunctioning. 5. Please follow instructions for repairing if any (e.g. battery replacement section); otherwise do not alternate or repair any parts of device except specified. 16 ZXHN H368C User’s Manual 6. Connection to party line service is subject to state tariffs. Contact the state public utility commission public service commission or corporation commission for information. 7. If the telephone company requests information on what equipment is connected to their lines, inform them of: a) The telephone number that this unit is connected to, b) The ringer equivalence number [0.1B ] c) The USOC jack required [RJ11C], and d) The FCC Registration Number US: ZTEDL01BHNH368CV1 Items (b) and (d) are indicated on the label. The ringer equivalence number (REN) is used to determine how many devices can be connected to your telephone line. In most areas, the sum of the RENs of all devices on any one line should not exceed five (5.0). If too many devices are attached, they may not ring properly. Service Requirements In the event of equipment malfunction, all repairs should be performed by our Company or an authorized agent. It is the responsibility of users requiring service to report the need for service to our Company or to one of our authorized agents. Service can be facilitated through our office at: Acadia Solutions, Inc.130 E. Wilson Bridge Road Suite 320 Worthington, OH 43085. Phone：614-505-613 17
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Encryption : Standard V4.4 (128-bit) User Access : Print, Annotate, Fill forms, Extract, Print high-res Author : MT01165 Modify Date : 2012:07:03 17:03:55+08:00 Create Date : 2012:06:22 10:11:32+08:00 Page Count : 25 Has XFA : No XMP Toolkit : XMP Core 4.1.1 Creator Tool : PScript5.dll Version 5.2.2 Metadata Date : 2012:06:26 11:45:36+08:00 Format : application/pdf Title : Microsoft Word - ZXHN H368C QSG_v1-00_ed1_2012-06-22.docx Creator : MT01165 Document ID : uuid:59ba0fa2-b470-4ae1-9310-60514cbe05ea Instance ID : uuid:0fe6aab9-4578-482e-b915-36665c5599df Producer : PDF-XChange Viewer [Version: 2.0 (Build 41.5) (Mar 30 2009; 19:53:50)] Page Layout : OneColumnEXIF Metadata provided by EXIF.tools