Zaptoys 1081-49 3" R/C Micro Polaris MSX Watercraft 1081 User Manual
Zaptoys International Limited 3" R/C Micro Polaris MSX Watercraft 1081 Users Manual
Zaptoys >
Users Manual
Mico Watercraft
Please read through this instruction manual carefully before
starting to operate.
Please ensure to remove all accessories and components from
packaging.
1. Disconnect transmitter into 2 separate units. The charger is the unit with
3 X AAA (1.5V) batteries installed.
2. Unplug the boat's charging socket cover.
3. Insert the charger into the charging socket.
4. When green light on the charger goes out, boat is charged.
5. Remove the charger, and re-plug the boat socket cover to prevent water
from entering.
1. Re-connect the charger unit into the transmitter to become a transmitter unit.
2. Extend the transmitter antenna to its full length.
3. Press buttons at both sides of the transmitter to pop up the cover to show
control buttons.
4. Before racing your boat, make sure that the antenna is standing vertically
upright for better signal receiving.
make sure the charging connector is in-line with the boat socket,
incorrect insertion will damage the charging socket.
Attention :
HELPFUL HINTS:
- Do not expose the boat to extreme temperatures.
- If the boat does not respond to the transmitter, move closer to the boats
and try again.
- If the boat starts to lose power. It may experience loss of performance
ability. If this happens. simply recharge your boat again.
- When the transmitter range decreases, replace the battery in the
controller.
MAINTENANCE AND CARE:
- If the boat becomes dirty, use a slightly dampened cloth to wipe
off the dirt and filth. Then use a dry cloth to wipe off the moisture.
- To remove dust particles, tie a small bit of cloth to the tip of a
toothpick, tweezers, etc, and wipe off.
- Do not use chemicals. The body of the boat can melt and
cause machine troubles.
- Be sure of remove the batteries from the transmitter when
storing the product away.
- Keep this Instruction Manual carefully for future use.
TROUBLE SHOOTING
Instruction Manual
#1081
1.What is in the package
2. Battery installation
3. Charging Your Micro Boat
4. Racing Your Micro Boat
5. How to play
Another Quality Product From QUALITY TOYSQUALITY TOYS
THIS PRODUCT IS FOR THE USE IN U.K., SPAIN, GERMANY, FRANCE, BELGIUM, ITALY,
SWITZERLAND, THE NETHERLANDS, DENMARK, U.S., CANADA AND PORTUGAL.
Recommended to use alkaline batteries for best performance,
3 X AAA (1.5V) batteries. (included)
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC Rules and R&TTE Directive 1999/5/EC.These
limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference the radio communications.However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
- Consult the dealer or an experienced radio/TV technician for help.
printed in china
0197
NO
English
.1081
©
ZAPTOYS 2004
MADE IN CHINA
Warning:
Changes or modifications to this unit not expressly approved by the party responsible
for compli ance could void the user's authority to operate the equipment
Transmitter Stand
1. Remove battery compartment cover located on the back of
the transmitter.
2. Insert 3 X AAA (1.5V) batteries into the transmitter following
the +/- marking.
3. Replace the battery cover.
Manual
1 & 3 2
1 & 4
green
light
1
green
light
2
charging socket
connection
button
button
control
buttons
3
Problem
Boat drives slowly
Poor range control
Cause
- Weak rechargeable batteries
in the boat.
- Weak batteries in transmitter
- Strong interference at the
surrounded area.
Correction
- Recharge the boat with the
charger.
- Replace with new batteries
- Move to a better location
to drive your boat.
CAUTION:
- Do not operate your boat where there are water plants, rubbish, filth, or
other obstacles
in the pond.
- Do not play where the water current is strong or when the wind is blowing
strongly.
- Do not play in ocean water, because salt water can cause rusting.
- Do not play in the thunderstorms.
- It is extremely dangerous to touch the propeller while it is spinning.
- The toy is designed for indoor use only. Outdoors use may lead to
malfunction caused by dirt or waste.
- Non-rechargeable batteries are not to be recharged
- Rechargeable batteries are to be removed from the toy being charged,
- Rechargeable batteries are only to be charged under adult supervision,
- Different types of batteries or new and used batteries are not to be mixed
- Only batteries of the same or equivalent type as recommended are to be
used.
- Batteries are to be inserted with the correct polarity.
- Exhausted batteries are to be removed from the toy
- The supply terminals are not to be short-circuited.
- The toy is to be operated in water only when fully assembled
Micro Polaris Watercraft
3
unplug
cover
2 & 5