Zebra Technologies AP7502 Dual Radio Wallplate AP User Manual AP 7502 11ac Wireless Wallplate Installation Guide

Zebra Technologies Corporation Dual Radio Wallplate AP AP 7502 11ac Wireless Wallplate Installation Guide

Users Manual

IntroductionThe AP-7502 11ac Wireless Wallplate is designed to leverage the existing category 5/5e/6 cabling already in the walls of any enterprise building. Ideally suited for hotels, dormitory housing, and similar multi-tenant buildings, the AP-7502 provides high speed wireless LAN along with switched Ethernet and PoE output.Document ConventionsThe following graphical alerts are used in this document to indicate notable situations:NOTE Tips, hints, or special requirements that you should take note of. CAUTION Care is required. Disregarding a caution can result in data loss or equipment malfunction. WARNING! Indicates a condition or procedure that could result in personal injury or equipment damage.Warnings• This equipment should only be installed by qualified professional installers.• Read all installation instructions and site survey reports, and verify correct equipment installation before installing this equipment.• Remove jewelry and watches before installing this equipment. • Verify proper wiring and grounding for each installation location.• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications (0° to 40° Celsius / 32° to 104° Fahrenheit).AP-7502 Wireless Wallplate SpecificationsWireless Interface Dual Radio; 802.11a/b/g/n/ac; 2.4 GHz and 5 GHzWAN Interface Auto-sensing 10/100/1000Mbps, Full/Half Duplex,with PoE receiving capability via RJ-45LAN Interfaces 3 x IEEE 802.3 10/100Mb, auto-sensing via RJ-45PoE Out One FE port with 802.3af output based on 802.3 at inputMedium DSSS, OFDM, MCS, HTNetwork Standards 802.11 a/b/g/n/ac, 802.11d, 802.11i, WPA, WMMPHY Data Rates802.11b: 1, 2, 5.5, 11 Mbps802.11g/a: 6, 9, 12, 18, 24, 36, 48, 54 Mbps802.11n: MCS 0-15 up to 300 Mbps802.11ac: MCS 0-8 up to 867 MbpsOperating Frequencies 802.11 operating frequencies: 2.4GHz @2400-2483.5 MHZ,5.2GHz @ 5150-5250 MHz and 5725-5850 MHzBluetooth LE 2400-2483.5 KHz in 2 MHz channelsTransmit Power 1dBm to 20dBm in 1dBm incrementsActual transmit power is dependent upon national limits.Antenna Configuration 2.4 GHz: 2 internal, 1x2, 2x2 MIMO, 5.8dBi peak gain5 GHz: 2 internal, 1x2, 2x2, MIMO, 7.3dBi peak gainManagement telnet, SSH, HTTP, HTTPS, SNMPv2/v3MOTOROLA SOLUTIONS, INC.1303 E. ALGONQUIN ROADSCHAUMBURG, IL 60196 http://www.motorolasolutions.comAP-7502 11ac Wireless Wallplate Installation GuideMN000912A01Revision A July 2014 (2)(1)(3) (4) (5) (6)Installing the AP-7502 WallplateThe AP-7502 wallplate can be installed over an existing structured wiring wallplate. When installing the wallplate over an existing 70mm x 115mm wallplate as is commonly found in North America, South America and Japan, install the decor facade (optional) only after the AP-7502 has been installed.1. Remove the existing wallplate.2. Install the wallplate mounting bracket.3. Attach the bottom of the wallplate to the mounting bracket and rotate the wallplate until it snaps onto the latch.4. Install the security screw provided (optional).5. If desired, install the decor facade.Basic AP-7502 Configuration To provide the Access Point with a basic configuration and access WiNG management functions, open a browser and enter the IP address printed on the serial label on the Access Point: https://<IP address of Access Point>Login to the system using the default username admin and password motorola.1. On the Configuration -> Basic Settings screen, enter the AP Name and Country Name.2. On the Configuration -> Wireless screen, enter the desired Name, SSID, Security, and WPA2 Key parameters.Additional WiNG configuration documentation is available at:https://portal.motorolasolutions.com/Support/US-EN Regulatory InformationThis device is approved under Motorola Solutions, Inc.This guide applies to Model Number AP-7502.All Motorola devices are designed to be compliant with rules and regulations in locations where they are sold and will be labeled as required.Local language translations are available at the following website: http://www.motorolasolutions.com/support.Any changes or modifications to Motorola equipment, not expressly approved by Motorola Solutions, could void the user's authority to operate the equipment.When Motorola devices are professionally installed, the Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation.Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations.This device is only to be used with a Motorola Wireless Switch.Declared maximum operating temperature: 40°C.Bluetooth® Wireless TechnologyThis is an approved Bluetooth® product. For more information or to view End Product Listing, please visit https://www.bluetooth.org/tpg/listings.cfmWireless Device Country ApprovalsRegulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe.Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at http://www.motorolasolutions.com/doc.Note: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Operation of the device without regulatory approval is illegal.Country SelectionSelect only the country in which you are using the device. Any other selection will make the operation of this device illegal. Some Access Points are specifically designed to operate in certain countries (Example; -US for the United States, -EU for the European Union) .Frequency of Operation - FCC and ICIndustry Canada Statement:Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL2.4 GHz OnlyThe available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited by firmware.Warnings for Use of Wireless DevicesPotentially Hazardous Atmospheres - Fixed InstallationsYou are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).Safety in HospitalsWireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected.PacemakersPacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research.Persons with Pacemakers:• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.• Should not carry the device in a breast pocket.• Should use the ear furthest from the pacemaker to minimize the potential for interference.• If you have any reason to suspect that interference is taking place, turn OFF your device.Other Medical DevicesPlease consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.
(8) (10) (12) (14)(7) (9) (11) (13)RF Exposure GuidelinesSafety InformationReducing RF Exposure - Use ProperlyOnly operate this device in accordance with the instructions supplied.InternationalThe device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on "International" human exposure to electromagnet fields refer to the Motorola Declaration of Conformity (DoC) at http://www.motorolasolutions.com/doc.For further information on the safety of RF energy from wireless devices - see http://responsibility.motorolasolutions.com/index.php/downloads/.Located under Wireless Communications and HealthEurope Remote and Standalone Antenna ConfigurationsTo comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 20cm from all persons.US and Canada Co-located StatementTo satisfy US and Canadian RF exposure requirements, a transmitting device must operate with a minimum separation distance of 20cm or more from a person's body.Pour satisfaire aux exigences Américaines et Canadiennes d'exposition aux radiofréquences, un dispositif de transmission doit fonctionner avec une distance de séparation minimale de 20cm ou plus de corps d'une personne.Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20m between the radiator and your body.NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps.Remote and Standalone Antenna ConfigurationsTo comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 20cm from all persons.Power SupplyThis device must be powered from a 802.3af or 802.3at compliant power source which has been certified by the appropriate agencies, or by a Motorola approved UL LISTED ITE (IEC/EN 60950-1, LPS/SELV) power supply with electrical ratings: Output 12Vdc, min 0.83 A or 48 Vdc min 0.57 A (POE), with a recommended ambient temperature greater than 40 or better degrees C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous..Radio Frequency Interference Requirements - FCCNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected• Consult the dealer or an experienced radio/TV technician for helpRadio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Radio Frequency Interference Requirements - CanadaCAN ICES-3 (B)/NMB-3(b)Radio TransmittersFor RLAN Devices:The use of 5 GHz RLAN's, for use in Canada, have the following restrictions:• Restricted Band 5.60 - 5.65 GHzLe présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications were met.In accordance with the regulations of Industry Canada, this radio transmitter can operate with an antenna of a type and a maximum gain (or lower) approved for the transmitter by Industry Canada. With the aim of reducing the risk of radio interference to other users, the chosen antenna type and it gain should be selected so that the equivalent isotropically radiated power (e.i.r.p.) does not exceed the intensity necessary for the establishment of a satisfactory connection.Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante.This radio transmitter IC: 109AN-AP7502 has been approved by Industry Canada to operate with the antenna types listed below and having a maximum gain allowable and the impedance required for each type of antenna. The antenna types not included in this list, or whose gain is higher than the maximum gain indicates, are strictly prohibited for the operation of the transmitter.Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numérode modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal etl'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur. Marking and European Economic Area (EEA)Class B ITEThe use of 2.4GHz RLAN's, for use through the EEA, have the following restrictions:• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.• Italy requires a user license for outside usage.Bluetooth® Wireless Technology for use through the EEA has the following restrictions:• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.Statement of Compliance for Wireless DevicesMotorola hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and 2011/65/EU. A Declaration of Conformity may be obtained from: http://www.motorolasolutions.com/docFrequency Type Maximum Gain Ohms2.4G-1 PCB-Dipole 5.81 dBi 502.4G-2 PCB-Dipole 4.52 dBi 505G-3 PCB-Dipole 7.22 dBi 505G-4 PCB-Dipole 7.30 dBi 50BT 2.4G-5 PCB-Dipole 4.74 dBi 50Waste Electrical and Electronic Equipment (WEEE)English: For EU Customers: All products at the end of their life must be returned to Motorola for recycling. For information on how to return product, please go to: http://www.motorola.com/recycling/weee.Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Motorola pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.motorola.com/recycling/weee.Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite:http://www.motorola.com/recycling/weee.Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на Motorola за рециклиране. За информация относно връщането на продукти, моля отидете на адрес: http://www.motorola.com/recycling/weee.Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Motorola zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unterhttp://www.motorola.com/recycling/weee.Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Motorola al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.motorola.com/recycling/weee.Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Motorola para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.motorola.com/recycling/weee.Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Motorola te worden teruggezonden voor recycling. Raadpleeg http://www.motorola.com/recycling/weee voor meer informatie over het terugzenden van producten.Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Motorola w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowejhttp://www.motorola.com/recycling/weee.Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Motorola'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: http://www.motorola.com/recycling/weee.Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.motorola.com/recycling/weee weboldalra.Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Motorola för återvinning. Information om hur du returnerar produkten finns på http://www.motorola.com/recycling/weee.Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Motorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.motorola.com/recycling/weee.Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.motorola.com/recycling/weee.Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Motorola za reciklažo. Za informacije o vra?ilu izdelka obiš?ite: http://www.motorola.com/recycling/weee.Turkish WEEE Statement of ComplianceKorea Warning Statement for Class B ITEChinese Warning Statement for Class A ITEOther CountriesAustraliaUse of 5 GHz RLAN's in Australia is restricted in the following band 5.50 - 5.65GHz.BrazilDeclarações Regulamentares- BrazilNota: A marca de certificação se aplica ao Transceptor, model AP-7502. Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.brEste equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.Este produto está homologado pela Anatel, de acordo com os procedimentos regulamentados pela Resolução n°242/2000 e atende aos requisitos técnicos aplicados, incluindo os limites de exposição da Taxa de Absorção Específica referente a campos elétricos, magnéticos e eletromagnéticos de radiofrequência, de acordo com as Resoluções n° 303/2002 e 533/2009.Este dispositivo está em conformidade com as diretrizes de exposição à radiofrequência quando posicionado pelo menos 20 centímetros de distância do corpo. Para maiores informações, consulte o site da Anatel.ChileEste equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas.Chinahttp://www.motorolasolutions.com/CN-ZH/Pages/Contact_Us#support_tab Quality CertificateHong KongIn accordance with HKTA1039, the band 5.15GHz - 5.35GHz is for indoor operation only’MexicoRestrict Frequency Range to: 2.450 - 2.4835 GHz.La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.S. KoreaUkraineThailandAP-7502 RoHS ComplianceService InformationIf you have a problem using the equipment, contact your facility’s technical or systems support. If there is a problem with the equipment, they will contact the Motorola Solutions Global Customer Support center.Contact information is available at: http://www.motorolasolutions.com/supportWhen contacting Motorola Solutions support, please provide the following information:• Serial number of the unit• Model number or product name• Software type and version numberMotorola Solutions responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you purchased your product from a Motorola Solutions business partner, contact that business partner for support.Customer Support Web SitesThe Motorola Solutions Support Central Web site, located at: http://www.motorolasolutions.com/support.provides information and online assistance including developer tools, software downloads, product manuals and online repair requests.Manualshttps://portal.motorolasolutions.com/Support/US-EN/Wireless+Networks.General InformationObtain additional information by contacting Motorola Solutions at:Telephone (North America): 1-800-722-6234

Navigation menu