Zebra Technologies CR2278 Presentation Cradle User Manual
Zebra Technologies Corporation Presentation Cradle
User Manual
CR2278 Presentation Cradle Quick Reference Guide Draft 1 2 CR2278 Presentation Cradle Introduction The CR2278-PC (presentation) cordless digital scanner cradle acts as charger and radio communication interface for the DS2278 cordless digital scanner. The CR2278-PC can sit on a desktop or be mounted on a wall. The cradle receives data from the digital scanner via a Bluetooth radio, and sends that data to the host through an attached cable. The cradle also charges the digital scanner’s internal battery when the digital scanner is inserted. The digital scanner can be charged from an external power supply or a USB cable powered by the host. This document provides basic instructions on setting up and using the cradle. Equipment Supplied The cradle package includes one CR2278-PC cradle. Accessories ??? verify The following equipment may be needed: • • • Power supply (for faster charging). Mounting bracket (must be purchased separately). Two M4 screws (for a bracket mount using the threaded brass screw holes, if applicable). Not available from Zebra. Save the shipping container for storing or shipping. Inspect all equipment for damage. If anything is damaged or missing, call an authorized Zebra Support Center immediately. Related Documentation • • DS2278 Digital Scanner Quick Start Guide, p/n MN-002916-xx. DS2278 Digital Scanner Product Reference Guide, p/n MN-002915-xx. All documentation and translations are available at: www.zebra.com/support. Service Information If you have a problem running your unit or using your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact Zebra Support at http://www.zebra.com/support. For the latest version of this guide go to: http://www.zebra.com/support. Draft 1 Quick Reference Guide Cradle Features Top Pairing Bar Code (in back) Charging/Communications Contacts LED Indicator Bottom Rubber Feet Host Interface Port Station Mount Threaded Brass Screw Holes (2 - M4 x 5 mm) Rubber Feet Cradle Connections 1. Connect the appropriate cable to the power supply and an AC power source, if necessary. This ensures detection of the host and prevent inadvertently back powering the cradle from improper detection of the host. Draft 1 4 CR2278 Presentation Cradle 2. Insert the interface cable into the host port. 3. Insert the interface cable into the cradle’s host port. 4. Pair the digital scanner to the cradle either by inserting it in the cradle (if Pair on Contacts is enabled) or by scanning the pairing bar code. ???verify 5. If necessary, scan the appropriate host bar code (for non-autodetected interfaces). Refer to the Product Reference Guide. Changing the Host Interface To connect to a different host, or to the same host through a different cable: 1. Unplug the interface cable from the host. 2. Unplug the power supply from the cradle. 3. Connect the interface cable to the new host, or the new interface cable to the existing host. 4. Reconnect the power supply, if required. 5. If necessary, scan the appropriate host bar code (for non-autodetected interfaces). Refer to the Product Reference Guide. Using a DC Power Supply The cradle can operate from host supplied power, if available. If host power is limited or not available, an external DC power supply can be used with certain host interface cables that support a power jack. An external power supply is recommended if fastest charging is required. CAUTION Always disconnect the DC power supply BEFORE disconnecting the cable to the host end or the cradle may not recognize the new host. Mounting the Cradle When placing the cradle on a tabletop, the rubber feet on the bottom of the cradle provide traction and prevent surface damage. To mount the cradle on a mounting bracket: 1. Install the mounting bracket in the appropriate location and secure in place. 2. Attach the interface and power cables to the cradle (see Cradle Connections on page 3). 3. Position the cradle on the mounting surface lining up the station mount threaded brass screw holes on the bottom of the cradle with the holes on the mounting bracket. 4. Attach the cradle securely to the surface using the two M4 screws. 5. Insert the digital scanner in the cradle. Draft 1 Quick Reference Guide Inserting the Digital Scanner in the Cradle. CAUTION Do not pour, spray, or spill any liquid on the cradle. Sending Data to the Host Computer The cradle receives data from the digital scanner via a wireless radio connection and transmits it to the host computer via the host cable. The digital scanner and cradle must be paired for successful wireless communication. Pairing NOTE The pairing bar code that connects the digital scanner to a cradle is unique to each cradle. Do not scan data or parameters until pairing completes. Only when the digital scanner is paired to the cradle, it automatically tries to reconnect to a remote device when a disconnection occurs that is due to the radio losing communication. Refer to the Product Reference Guide for more information. Pairing is the process by which a digital scanner initiates communication with a cradle. To pair the digital scanner with the cradle, scan the pairing bar code. A high/low/high/low beep sequence indicates that the pairing bar code was decoded. When a connection between the cradle and digital scanner is established, a low/high beep sounds. Draft 1 6 CR2278 Presentation Cradle Lost Connection to Host If scanned data does not transmit to the cradle’s host, ensure that all cables are firmly inserted and the power supply is connected to an appropriate AC outlet, if applicable. If scanned data still does not transmit to the host, reestablish a connection with the host: 1. Disconnect the host interface cable from the cradle. 2. Wait three seconds. 3. Reconnect the host interface cable to the cradle. 4. Reestablish pairing with the cradle by scanning the pairing bar code. Charging the Digital Scanner Battery in the Cradle When using a new battery in the digital scanner, the battery requires a charge to be enabled. Insert the battery in the digital scanner and place the digital scanner in the cradle (see Inserting the Digital Scanner in the Cradle. on page 5). The battery begins charging when the cradle LED indicator starts flashing amber. The battery is fully charged when the cradle LED is solid green. A complete charge of a fully discharged battery can take up to three hours using external power. Cradle LED Indicators ???verify/update LED Indication Standard Use Green (stays on) Power Up Radio Indications Green (off, then on) Bluetooth connection established Battery Indications Amber (stays on) Pre-charging Amber blinking Charging Green (stays on) Fully charged Amber fast blinking Charging Error Battery End of Life Indications Red blinking Charging Red (stays on) Fully charged Red fast blinking Charging error Draft 1 Quick Reference Guide LED Indication Maintenance Indications Red (stays on) Enter boot loader Red blinking Firmware installation Troubleshooting If the cradle does not work after following the previous procedures: • • • • • Check the system power. Check for loose cable connections. Check that the digital scanner is inserted properly in the cradle. Check that the host settings are correct and the cradle is connected to the appropriate port on the host. If water spills on the contacts area, the unit might not function properly. Turn the power off and tilt the cradle to drain as much liquid as possible. Do not shake the cradle. Use a paper towel to dry the outside surfaces, and expose the unit to room conditions for up to 24 hours to allow liquid to dry around the contacts. Health and Safety Recommendations Ergonomic Recommendations In order to avoid or minimize the potential risk of ergonomic injury, follow the recommendations below. Consult with your local Health and Safety Manager to ensure that you are adhering to your company's safety programs to prevent employee injury. Reduce or eliminate repetitive motion. Maintain a natural position. Reduce or eliminate excessive force. Keep objects that are used frequently within easy reach. Perform tasks at correct heights. Reduce or eliminate vibration. Reduce or eliminate direct pressure. Provide adjustable workstations. Provide adequate clearance. Provide a suitable working environment. Improve work procedures. CAUTION • • • • • • • • • • • Regulatory Information This device is approved under Zebra Technologies Corporation. This guide applies to Model Number CR2278. All Zebra devices are designed to be compliant with the rules and regulations in the locations they are sold and will be labeled as required. Draft 1 8 CR2278 Presentation Cradle Local language translations are available at the following website: http://www.zebra.com/doc. Any changes or modifications to Zebra equipment not expressly approved by Zebra could void the user's authority to operate the equipment. For use only with Zebra approved and UL Listed mobile computers, Zebra approved, and UL Listed/Recognized battery packs. Bluetooth® Wireless Technology This is an approved Bluetooth® product. For more information or to view the End Product Listing, please visit https://www.bluetooth.org/tpg/listings.cfm. Wireless Device Country Approvals Regulatory markings subject to certification are applied to the device signifying the radio(s) is/are approved for use in the following countries and continents: United States, Canada, Japan, China, South Korea, Australia, and Europe. Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at: http://www.zebra.com/doc. Note: Europe includes Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland, and the United Kingdom. CAUTION Operation of the device without regulatory approval is illegal. Warnings for Use of Wireless Devices CAUTION Please observe all warning notices with regard to the usage of wireless devices. Potentially Hazardous Atmospheres - Fixed Installations You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc. and areas where the air contains chemicals or particles such as grain, dust, or metal powders. Safety in Hospitals Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely affected. Draft 1 Quick Reference Guide Pacemakers Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research. Persons with Pacemakers: • Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON. • Should not carry the device in a breast pocket. • Should use the ear furthest from the pacemaker to minimi e the potential for interference. • If you have any reason to suspect that interference is taking place, turn OFF your device. Other Medical Devices Please consult your physician or the manufacturer of the medical device to determine if the operation of your wireless product may interfere with the medical device. RF Exposure Guidelines Safety Information • Reducing RF Exposure - Use Properly • Only operate the device in accordance with the instructions supplied. International The device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on 'International' human exposure to electromagnetic fields, refer to the Zebra Declaration of Conformity (DoC) at http://www.zebra.com/doc. • For further information on the safety of RF energy from wireless devices, see https://www.zebra.com/us/en/about-zebra/company-information/corporat e-responsibility.html located under Corporate Responsibility. US and Canada Co-located statement To comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located or operating in Draft 1 10 CR2278 Presentation Cradle conjunction with any other transmitter/antenna except those already approved in this filling. IMPORTANT NOTE: (For mobile device use) Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles) Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. To satisfy FCC RF exposure requirements, a mobile transmitting device must operate with a minimum separation distance of 20 cm or more from a person's body. Power Supply Use ONLY a Zebra approved UL LISTED ITE (IEC/EN 60950-1, LPS/SELV) power supply with electrical ratings: Output 5Vdc, min 0.8A, with a maximum ambient temperature of at least 50 degrees C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous. Radio Frequency Interference Requirements-FCC Tested to comply with FCC Standards FOR HOME OR OFFICE USE Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. Draft 1 Quick Reference Guide • • • 11 Increase the separation between the equipment and receiver. Connect the equipment in an outlet on a circuit different from the receiver is connection. Consult the dealer or an experienced radio/TV technician for help. Radio Transmitters (Part 15) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Radio Frequency Interference Requirements-Canada CAN ICES-3 (B)/NMB-3(B) Radio Transmitters This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi même si le brouillage est susceptible d'en compromettre le fonctionnement. Label Marking: The Term 'IC:' before the radio certification only signifies that Industry Canada technical specifications were met. Etiquette de marquage: Le terme "IC" avant la certification radio signifie que le produit est compatible avec le spécification Industrie Canada CE Marking and European Economic Area (EEA) Bluetooth® Wireless Technology for use through the EEA have the following restrictions: • Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz. Statement of Compliance Zebra hereby declares that this radio equipment is in compliance with Directive 2011/65/EU and 1999/5/EC or 2014/53/EU (2014/53/EU supersedes 1999/5/EC from 13th June 2017). The full text of the EU Declaration of Conformity is available at the following internet address: http://www.zebra.com/doc. Draft 1 12 CR2278 Presentation Cradle Japan (VCCI) - Voluntary Control Council for Interference Class B ITE Korea Warning Statement for Class B ITE 기종별 사용자안내문 B 급 기기 (가정용 방송통신기자재) 이 기기는 가정용(B급) 전자파적합기기로 서 주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. Other Countries Brazil (UNWANTED EMISSIONS - ALL PRODUCTS) Declarações Regulamentares para CR2278 - Brazil Nota: A marca de certificação se aplica ao Transceptor, modelo CR2278. Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br. Chile Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas China 通过访问以下网址可下载当地语言支持的产品说明书 www.zebra.com/support 合格证: Draft 1 Quick Reference Guide 13 Eurasian Customs Union Евразийский Таможенный Союз Данный продукт соответствует требованиям знака EAC. Mexico Restrict Frequency Range to: 2.450 - 2.4835 GHz. La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. South Korea For a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expression should be displayed; 해당 무선설비는 운용 중 전파혼신 가능성이 있음 해당 무선설비는 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스 는 할 수 없습니다 Taiwan 臺灣 低功率電波輻射性電機管理辦法 第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅 自變更頻率、加大功率或變更原設計之特性及功能。 第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象 時,應立即停用,並改善至無干擾時方得繼續使用。 前項合法通信,指依電信規定作業之無線電通信。 低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之 干擾。 Ukraine Дане обладнання відповідає вимогам технічного регламенту №1057, № 2008 на обмеження щодо використання деяких небезпечних речовин в електричних та електронних пристроях. Thailand เครื่ องโทรคมนาคมและอุปกรณ์น้ ี มีความสอดคล้องตามข้อกําหนดของ กทช. Turkish WEEE Statement of Compliance EEE Yönetmeliğine Uygundur. Draft 1 14 CR2278 Presentation Cradle CMM Disclosure 10 ᴿᇩ⢟䍞 (Parts) (Metal Parts) (Circuit Modules) (Cables and Cable Assemblies) (Plastic and Polymeric Parts) (Optics and Optical Components) (Batteries) (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 本表格依据SJ/T 11364 的规定编制。 O: X: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量 要求以下。 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的 限量要求。( 企业可在此处,根据实际情况对上表中打 “×” 的技术原因进行 进一步说明。) This table was created to comply with China RoHS requirements. Waste Electrical and Electronic Equipment (WEEE) English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: http://www.zebra.com/weee. Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : http://www.zebra.com/weee. Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: http://www.zebra.com/weee. Bulgarish: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на Zebra за рециклиране. За информация относно връщането на продукти, моля отидете на адрес: http://www.zebra.com/weee. Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter http://www.zebra.com/weee. Draft 1 Quick Reference Guide 15 Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: http://www.zebra.com/weee. Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.zebra.com/weee. Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg http://www.zebra.com/weee voor meer informatie over het terugzenden van producten. Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej http://www.zebra.com/weee. Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: http://www.zebra.com/weee. Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: http://www.zebra.com/weee. Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a http://www.zebra.com/weee weboldalra. Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du returnerar produkten finns på http://www.zebra.com/weee. Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa http://www.zebra.com/weee. Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: http://www.zebra.com/weee. Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται στην Zebra για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός προϊόντος, επισκεφθείτε τη διεύθυνση http://www.zebra.com/weee στο ∆ιαδίκτυο. Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: http://www.zebra.com/weee. Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi: http://www.zebra.com/weee. Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o vračilu izdelka obiščite: http://www.zebra.com/weee. Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: http://www.zebra.com/weee. Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite: http://www.zebra.com/weee. Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu, skatiet: http://www.zebra.com/weee. Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: http://www.zebra.com/weee. Hrvatski: Za kupce u Europskoj uniji: Svi se proizvodi po isteku vijeka trajanja moraju vratiti tvrtki Zebra na recikliranje. Informacije o načinu vraćanja proizvoda potražite na web-stranici: http://www.zebra.com/weee. Draft 1 Zebra Technologies Corporation 3 Overlook Point Lincolnshire, Illinois 60069 USA http://www.zebra.com Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in many jurisdictions worldwide. All other trademarks are the property of their respective owners. © 2017 Symbol Technologies LLC, a subsidiary of Zebra Technologies Corporation. MN-002917-01 Revision A - March 2017 Draft 1
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Zebra Technologies Corporation Create Date : 2011:02:04 10:45:09Z Modify Date : 2017:04:25 14:39:52+08:00 Subject : MN-002854-02 Rev. A Has XFA : No Language : en XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Format : application/pdf Title : CR8178-PC Presentation Cradle Quick Reference Guide (en) Creator : Zebra Technologies Corporation Description : MN-002854-02 Rev. A Creator Tool : FrameMaker 2015.2 Metadata Date : 2017:04:25 14:39:52+08:00 Producer : Acrobat Distiller 11.0 (Windows) Document ID : uuid:78edb5a5-86f0-4e34-9cb0-949b7ffcdd51 Instance ID : uuid:3bef792e-127d-4eb6-adf4-6c8027f5de02 Page Mode : UseNone Page Count : 16EXIF Metadata provided by EXIF.tools