Zebra Technologies KHUSB600 802.11 a/b/g/n USB Dongle User Manual

Zebra Technologies Corporation 802.11 a/b/g/n USB Dongle

User manual

IntroductionThe MOD-8132-6001S sensor module is a USB sensor extension to the AP-8132model access point for use with the Motorola Solutions ADSP platform. It provideswireless security sensing mechanisms, allowing monitoring and reporting within theAP-8132's radio coverage area. The output of the sensor's detection mechanisms arereported within the ADSP system.Document ConventionsThe following graphical alerts are used in this document to indicate notablesituations:NOTE Tips, hints, or special requirements that you should take note of.CAUTION Care is required. Disregarding a caution can result in dataloss or equipment malfunction.WARNING! Indicates a condition or procedure that could result inpersonal injury or equipment damage.Warnings• Read all installation instructions and site survey reports, and verify correct equipmentinstallation before connecting the MOD-8132-6001S sensor module.•Remove jewelry and watches before installing this equipment.•Verify any device connected to this unit is properly wired and grounded.•Verify there is adequate ventilation around the device, and that ambient temperatures meetequipment operation specifications.PrecautionsBefore installing an MOD-8132-6001S sensor module, verify the following:•You are using one of the correctly rated power solutions for the AP-8132 access point:- AP-PSBIAS-2P3-ATR power injector- PWRS-14000-247R external power supply•Motorola Solutions recommends you do not to install the MOD-8132-6001S in wet or dustyareas.•Verify the environment has a continuous temperature range between 0° C to 50° C.SpecificationsLength 2.5 in /6.3 cmWidth 6.0 in / 15.24 cmHeight 1.625 in / 4.127 cmWeight 0.270 lb / 0.123 kgOperating Temperature 0°to 50°celsius / 35°to 122°farenheitStorage Temperature -20°to 80°celsius / -4°to 176°farenheitRadio Technology 2x2 MIMO 802.11 a/b/g/nThe MOD-8132-6001S sesnsor module is plenum rated.MOTOROLA SOLUTIONS INC.1303 E. ALGONQUIN ROADSCHAUMBURG, IL 60196http://www.motorolasolutions.comMOD-8132-6001S Internal Antenna Sensor Module Installation Guide72-167783-01Revision B January 2013 (2)(1)(3) (4) (5) (6)Installing the MOD-8132-6001S Internal Antenna Sensor Module1. Align the tabs on the sensor module with the corresponding slots on theAccess Point.2. Securely attach the sensor module to the Access Point.3. Confirm the sensor module is operational by observing its LEDs.Regulatory InformationThis device is approved under Motorola Solutions, Inc.This guide applies to Model Number KHUSB600.All Motorola devices are designed to be compliant with rules and regulations in locationswhere they are sold and will be labeled as required.Local language translations are available at the following website:http://supportcentral.motorola.com.Any changes or modifications to Motorola Solutions equipment, not expressly approved byMotorola Solutions, could void the user's authority to operate the equipment.When Motorola Solutions devices are professionally installed, the Radio Frequency OutputPower will not exceed the maximum allowable limit for the country of operation.This device is only to be used with a Motorola Solutions AP-8132 Access Point.Wireless Device Country ApprovalsRegulatory markings, subject to certification, are applied to the device signifying the radio(s)is/are approved for use in the following countries: United States, Canada, Japan, China, S.Korea, Australia, and Europe (Note 1,2).Please refer to the Declaration of Conformity (DoC) for details of other country markings. Thisis available at http://www.motorola.com/doc.Note 1: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, CzechRepublic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway,Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and theUnited Kingdom.Note 2: Operation of the device without regulatory approval is illegal.Country SelectionSelect only the country in which you are using the device. Any other selection will make theoperation of this device illegal.Frequency of Operation - FCC and IC5 GHz OnlyThe use in the UNII (Unlicensed National Information Infrastructure) band 1 (5150-5250 MHz)is restricted to Indoor Use Only; any other use will make the operation of this device illegal.Industry Canada Statement:Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potentialfor harmful interference to co-Channel mobile satellite systems. High power radars areallocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHzand these radars could cause interference and/or damage to LE-LAN devices.Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservéuniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillagepréjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radarspourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.Health and Safety RecommendationsWarnings for Use of Wireless DevicesPlease observe all warning notices with regard to the usage of wireless devices.Potentially Hazardous Atmospheres - Fixed InstallationsYou are reminded of the need to observe restrictions on the use of radio devices in fuel depots,chemical plants etc. and areas where the air contains chemicals or particles (such as grain,dust, or metal powders).Safety in HospitalsWireless devices transmit radio frequency energy and may affect medical electrical equipment.When installed adjacent to other equipment, it is advised to verify that the adjacent equipmentis not adversely affected.PacemakersPacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintainedbetween a handheld wireless device and a pacemaker to avoid potential interference with thepacemaker. These recommendations are consistent with independent research andrecommendations by Wireless Technology Research.Persons with Pacemakers:• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemakerwhen turned ON.• Should not carry the device in a breast pocket.• Should use the ear furthest from the pacemaker to minimize the potential forinterference.• If you have any reason to suspect that interference is taking place, turn OFF yourdevice.Other Medical DevicesPlease consult your physician or the manufacturer of the medical device, to determine if theoperation of your wireless product may interfere with the medical device.RF Exposure GuidelinesSafety InformationReducing RF Exposure - Use ProperlyOnly operate the device in accordance with the instructions supplied.InternationalThe device complies with internationally recognized standards covering human exposure toelectromagnetic fields from radio devices. For information on "International" human exposureto electromagnetic fields refer to the Motorola/Symbol Declaration of Conformity (DoC) athttp://www.motorola.com/doc.US and CanadaCo-located statementTo comply with FCC RF exposure compliance requirement, the antenna used for this transmittermust not be co-located or operating in conjunction with any other transmitter/antenna exceptthose already approved in this filling.Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth foa na uncontrolledenvironment. This equipment should be installed and operated with minimum distance 30cmbetween the radiator and your body.NOTE IMPORTANTE: (Pour l'utilisation de dispositifs mobiles)Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour unenvironnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de30 cm de distance entre la source de rayonnement et votre corps.
(8) (10) (12) (14)(7) (9) (11) (13)Radio Frequency Interference Requirements - FCCThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses andcan radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However there is noguarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turningthe equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected• Consult the dealer or an experienced radio/TV technician for help.Radio Transmitters (Part 15)This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.The use of 5 GHz WLAN's, for use in the US , have the following restrictions:• Notched Band 5.60 - 5.65 GHzRadio Frequency Interference Requirements - CanadaThis Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Radio TransmittersFor RLAN Devices:The use of 5 GHz RLAN's, for use in Canada, have the following restrictions:Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareilsradio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) ledispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter toutbrouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnementindésirable.Tested to ComplyWith FCC StandardsFor Home or Office UseSymbol Technologies Inc.Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canadatechnical specifications were met.Marking and European Economic Area (EEA)The use of 2.4GHz RLAN’s, for use through the EEA, have the following restrictions:• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400-2.4835 GHz.• Italy requires a user license for outside usage.Statement of ComplianceMotorola Solutions hereby declares that this device is in compliance with all the applicableDirectives, 1999/5/EC. A Declaration of Conformity may be obtained fromhttp://www.motorola.com/doc.Japan (VCCI) - Voluntary Control Council for InterferenceClass B ITEKorea Warning Statement for Class B ITEOther CountriesAustraliaUse of 5GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65GHz.BrazilDeclarações Regulamentares para AP-8132 - BrasilNota: A marca de certificação se aplica ao Transceptor, modelo AP-8132. Este equipamentoopera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial,mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando emcaráter primário. Para maiores informações sobre ANATEL consulte o site: www.anatel.gov.br.ChileEste equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria detelecomunicaciones, relativa a radiaciones electromagnéticas.ChinaTaiwanThailandWaste Electrical and Electronic Equipment (WEEE)English: For EU Customers: All products at the end of their life must be returned to Motorola forrecycling. For information on how to return product, please go to: http://www.motorola.com/recycling/weee.Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent êtreretournés à Motorola pour recyclage. Pour de plus amples informations sur le retour de produits,consultez : http://www.motorola.com/recycling/weee.Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorolaal final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómodevolver un producto, visite: http://www.motorola.com/recycling/weee.Bulgarish: За клиенти от ЕС:След края на полезния им живот всички продукти трябва да се връщат на Motorola за рециклиране.За информация относно връщането на продукти, моля отидете на адрес: http://www.motorola.com/recycling/weee.Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zumRecycling an Motorola zurückgesandt werden. Informationen zur Rücksendung von Produktenfinden Sie unter http://www.motorola.com/recycling/weee.Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vitadevono essere restituiti a Motorola al fine di consentirne il riciclaggio. Per informazioni sullemodalità di restituzione, visitare il seguente sito Web: http://www.motorola.com/recycling/weee.Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos àMotorola para reciclagem. Para obter informações sobre como devolver o produto, visite: http://www.motorola.com/recycling/weee.Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naarMotorola te worden teruggezonden voor recycling. Raadpleeg http://www.motorola.com/recycling/weee voor meer informatie over het terugzenden van producten.Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ dofirmy Motorola w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronieinternetowej http://www.motorola.com/recycling/weee.Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgilMotorola'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi:http://www.motorola.com/recycling/weee.Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola vállalathoz kelleljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatostudnivalókért látogasson el a http://www.motorola.com/recycling/weee weboldalra.Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras tillMotorola för återvinning. Information om hur du returnerar produkten finns på http://www.motorola.com/recycling/weee.Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksiMotorola-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta onosoitteessa http://www.motorola.com/recycling/weee.Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola til recirkulering, når de erudtjent. Læs oplysningerne om returnering af produkter på: http://www.motorola.com/recycling/weee.Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Motorolaza reciklažo. Za informacije o vra ilu izdelka obiš ite: http://www.motorola.com/recycling/weee.Turkish WEEE Statement of ComplianceMotorola Solutions Support CenterIf you have a problem with your equipment, contact support for your region.Contact information is available at: http://motorolasolutions.com/support.When contacting Motorola Solutions support, please provide the followinginformation:• Serial number of the unit• Model number or product name• Software type and version numberMotorola Solutions responds to calls by e-mail, telephone, or fax within the timelimits set forth in support agreements. If you purchased your product from a MotorolaSolutions business partner, contact that business partner for support.Customer Support Web SitesThe Motorola Solutions Support Central Web site, located at:http://supportcentral.motorola.com/provides information and online assistance including developer tools, softwaredownloads, product manuals and online repair requests.Manualshttp://supportcentral.motorola.com/support/product/manuals.doGeneral InformationObtain additional information by contacting Motorola Solutions at:Telephone (North America): 1-800-722-6234Telephone (International): +1-631-738-5200Website: http://www.motorolasolutions.com

Navigation menu