Zebra Technologies MC67NA ENTERPRISE DIGITAL ASSISTANT (EDA) User Manual 2

Zebra Technologies Corporation ENTERPRISE DIGITAL ASSISTANT (EDA) 2

User Manual 2

100Mbps231261158123791012733123432512343572688610910 918171319141521162022231343592221021234325869101 Talk2 Navigation3 Soft Key4 Scan/Action Button5 EndNote 1: To reset the MC67, press and hold the Power button for five (5) seconds. Numeric Keypad Alpha-Numeric Keypad PIM Keypad Blue Key Use this key to access function keys shown on the keypad in blue.>Orange KeyUse this key to access the secondary layer of characters and actions.>>>>>Press the Blue key once to activate this state temporarily, followed by another key. Press the Blue key twice to lock this state. Press the Blue key a third time to unlock.Press the Orange key once to activate this state temporarily, followed by another key. Press the Orange key twice to lock this state. Press the Orange key a third time to unlock.NotificationsCharging/Battery Status LED:Scan/Decode LED:Slow blinking amber: Battery chargingSolid amber: Fully chargedFast blinking amber: Charging errorRed: Scanning activeGreen: Good DecodeScan/DecodeCharging/Battery StatusRadio StatusRadio Status LED:Green: RF activeUsing the Single-slot USB CradleUsing the Four-Slot Spare Battery ChargerSlow Blinking Amber = ChargingCharging/Battery Status LEDSolid Amber = Fully chargedFast Blinking Amber = Charging errorNote:The 3600 mAh battery charges in less than six hours.Use the Four-slot Battery Charger to charge batteries separately.Note: Remove protective shipping film that covers the touch screen, exit window and camera window before using.Press the Orange key once to lock the keypad into Alpha state. Press the Orange key a second time to return to the normal state.Press the Blue key once to activate this state, followed by another key.Blue Key Use this key to access function keys shown on the keypad in blue.>Orange KeyUse this key to access the secondary layer of characters.>>4 (Note 1)FEATURES CARD INSTALLATION BATTERY INSTALLATION CHARGINGMicroSD Card Installation (Optional)1. Remove the handstrap.2. Lift the rubber access door.3. Slide the SIM card holder up to unlock.4. Lift the SIM card holder.5. Carefully lift the microSD card holder.6. Insert the microSD card into the card holder.NOTE :Proper position of the microSD card — the card connector (i.e., gold contacts) should be facing out as shown.7. Gently lower the microSD card holder until it snaps into place.SIM Card HoldermicroSD Card HolderRubber Access DoorSIM Card Installation (Optional)8. Insert the SIM card into the SIM holder.NOTE :The proper position of the SIM card—the card connector (i.e., gold area) should be facing outward with the beveled corner facing away.9. Lower the SIM card holder.10. Slide the SIM card holder down to lock into place.11. Close the rubber access door.12. Install the battery.1. Insert the battery, bottom first, into the battery compartment.2. Press down on the battery until the battery latch snaps into place.3. Replace the handstrap.MC67QUICK START GUIDE Use the Single-slot USB cradle or Four-slot cradles (Charge Only or Ethernet) to charge the battery in the MC67.Also charge a spare battery using the Single-slot cradle.Using the Four-slot Cradles1 Scan/Action Button2 Up/Down Button3 Microphone4 Power Button5 I/O Connector 6 Keypad7 Scan/Action Button8 Touch Screen (with screen protector)9 Data Capture LED10 Charging/Battery Status LED11 WAN Radio Status LED12 Phone Speaker13 Handstrap14 Battery15 Battery Latch16 Camera Flash (optional)17 Camera (optional)18 Exit Window (see Data Capture Options)19 Tether20 Scan/Action Button21 Action Button22 Stylus 23 Speaker3DSD Keypad 6 Orange Key7 Backlight8 Blue Key9 OK10 Start MenuPRELIMINARY
AVOID EXTREMEWRIST ANGLESMC67 QUICK START GUIDEMOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.© 2012 Motorola Solutions, Inc. All Rights Reserved.72-161172-01 Rev. 1 — February 2012http://www.motorolasolutions.com/MC67Imaging Camera DecodeCamera Photo1. Launch a bar code reading application on the MC67.2. Position the MC67 toward the bar code.3. Press the Scan button.4. In the image window align the red target over the bar code. When the MC67 decodes the bar code the Scan/Decode LED light green and a beep sounds.5. Release the Scan button.1. Tap Start > Programs > Pictures & Videos > Camera.2. Point the MC67 at an object.3. Press the Enter button.4. Hold MC67 still until “Shutter Sound” is heard.Motorola Solutions, Inc.1301 E. Elgonquin Rd. Schaumburg, IL 60196-1078, U.S.A.GPS Information• Acquiring satellite signals may take a few minutes. It is best to be outside and have a clear, unobstructed view of the sky.• Without a clear view, acquisition takes much longer and could result in the MC67 being unable to compute the initial position quickly.• Obtain a satellite fix before moving.• Shutdown GPS application when not in use.When using the GPS feature of the MC67:COMMUNICATIONBATTERY REMOVAL DATA CAPTURE OPTIONS AVOID EXTREME WRIST ANGLESCharge Only CableAuto Charge CableUSB/Charge CableFour-slot Battery ChargerSingle-slot USB CradleVehicle HolderFour-slot Charge Only CradleFour-slot Ethernet CradleVehicle CradleScreen ProtectorMotorola Solutions recommends the continued use of a screen protector to minimize wear and tear. Screen protectors enhance the usability and durability of touch screen displays.Benefits include:• Protection from scratches and gouges• Durable writing and touch surface with tactile feel• Abrasion and chemical resistance• Glare reduction• Keeping the device’s screen looking like new• Quick and easy installation.Not using a screen protector can affect your warranty coverage.An initial screen protector is already applied to your MC67.Contact your local account manager or Motorola Solutions, Inc. for more information and purchasing details.Part number: KT-67525-01R Screen Protector 3/pk.Trigger HandleMagnetic Stripe ReaderCreate a PartnershipInstall Synchronization SoftwareCommunicate with HostACCESSORIES1. If the MC67 is in suspend mode, press the Power button to wake the MC67.2. Press the Power button to place the MC67 in suspend mode.3. Tap Safe Battery Swap.4. Wait for the Data Capture LED to turn red and then turn off.5. When the LED turns off, remove the handstrap.6. Slide the battery latch to the right. The battery ejects slightly.7. Grasp the battery and lift from the MC67.Download Mircosoft® ActiveSync® (Windows® XP) or Windows Mobile Device Center (Windows 7) from http://www.microsoft.com and follow the instructions to install onto the host computer.Follow the on-screen instructions to establish a connection between the MC67 and the host computer.

Navigation menu