Zebra Technologies MD-ZCLFHF LF/HF Module User Manual Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	3788666
Application ID	+xsnT1kQxNpkz6c7AGteaA==
Document Description	Installation Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.58kB (819754 bits)
Date Submitted	2018-03-20 00:00:00
Date Available	2018-03-20 00:00:00
Creation Date	2017-08-25 14:14:55
Producing Software	Acrobat Distiller 11.0 (Windows)
Document Lastmod	2018-03-19 10:19:19
Document Title	Installation Guide
Document Creator	PScript5.dll Version 5.2.2

Installation Guide
T4NM-FDC0
ZQ3BT
Compliance and Regulatory Statements
FCC Compliance Statement (USA)
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for Class B Digital Devices,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a residential environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the product manuals, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, the
user is encouraged to do one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced RF service technician for help.
The end product must be labeled, in a visible area, with the following:
Contains FCC ID: I28MD-ZCLFHF
Modification Warning
The user is cautioned that any changes or modifications not expressly approved by Zebra
Technologies could void the user s authority to operate the equipment. To ensure compliance, this
printer must be used with fully shielded communication cables.
RF Exposure Statement
This transmitter complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter, except in accordance with FCC multi- transmitter product procedures.
Canadian DOC Compliance Statement
Cet appareil numerique de la classe B est conforme a la norme NMB-003 du
Canada. This Class B digital apparatus complies with Canadian ICES-003.
Industry Canada (IC) Warning
Le present appareil est conforme aux CNR d Industrie Canada applicables aux appareils
radio exempts de licence. L exploitation est autorisee aux deux conditions suivantes : (1)
appareil ne doit pas produire de brouillage, et (2) l utilisateur de l appareil doit accepter
tout brouillage radioelectrique subi, meme si le brouillage est susceptible n
compromettre le fonctionnement.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: 1) This device may not cause interference., 2)
This device must accept any interference, including interference that may cause undesired
operation of the device.
The end product must be labeled, in a visible area, with the following:
Contains IC: 3798B-ZCLFHF
3798B- ZBRZQ3BT
Approved Antenna information
Only the integrated antenna on module is allowed and cannot be user replaceable.
General
T4NM-FDC0 module has been certified as a Limited Single Modular. Additional
The ZQ3BT
evaluation is required for use in all host devices. The following describes the installation procedures
for the various hosts in which the module has been evaluated.
Installation Instructions for Zebra Printers
T4NM-FDC0 is not intended for OEM integrators or end users. It can only be installed in the
The ZQ3BT
Zebra printers at the grantee manufacturing facility.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : 
Create Date                     : 2017:08:25 14:14:55-07:00
Modify Date                     : 2018:03:19 10:19:19-07:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2018:03:19 10:19:19-07:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Format                          : application/pdf
Creator                         : 
Title                           : 
Document ID                     : uuid:aae26652-e70e-4ba6-92cb-eb17bd672446
Instance ID                     : uuid:110b6070-2f7d-4310-a92c-b470a21ec06a
Page Count                      : 2

EXIF Metadata provided by EXIF.tools