Zebra Technologies RFD8500 RFD8500 UHF RFID READER User Manual BETA QSG FOR REG TESTING Front

Zebra Technologies Corporation RFD8500 UHF RFID READER BETA QSG FOR REG TESTING Front

User manual

ORRemove the battery cover from the RFD8500. Remove the plastic tip from the cover. Attachthe mobile computer to its case accessory. Attach the mobile computer case to the RFD8500battery cover. Slide the battery cover onto the RFD8500 until it locks in place. The batterycover latches secure the mobile computer to the RFD8500.614375281a3a109Slow Flash = Normal ChargeCharge LED Indicator Solid Green = Full ChargeTo remove the mobile computer, press the battery cover release latches, and pull the mobile computer back and up.1 Battery Cover Release Latch1a Battery Compartment2 Trigger3 Bluetooth Button/Indicator3a Beeper 4 Mode Button/Indicator 5 Imager Window (Imager units only) 6 Antenna7 Power Button8 Charging Contacts9 Decode IndicatorFEATURESCHARGING AND COMMUNICATIONDEVICE INSTALLATIONSOFTWARE AND SCANNINGRFD8500Quick Start GuideInstall RFD8500 Software on Mobile ComputerIn order to use the RFD8500 with a mobile computer, software installationis required. Download the software file from the ZebraSupport Central web site: www.zebra.com/support. Follow the instructions provided with the software and install the file onto thedevice using ActiveSync. For more information, refer to the appropriate mobile computer User Guide at: www.zebra.com/support. Inserting the Mobile Computer into the RFD8500Removing the Mobile Computer from the RFD8500Charging and CommunicationThe RFD8500 can be used to charge the battery of a mobile computer, and communicate with a host computer. The recommended form of communication to the mobile computer is via USB charge/communication cable.Insert the BatteryRemove the Battery1. Insert the battery, connector end first, into the battery compartment.2. Press down on the battery until the battery latch snaps into place.GETTING STARTED - BATTERY INSTALLATION1. Remove the battery cover. 2. Remove battery as shown. IntroductionThe RFD8500 adds an RFID gun-style handle with a scanning triggerto the mobile computer. Used for all RFID operations, the RFD8500 increasescomfort when using the mobile computer in scan-intensive applications forextended periods of time. Left ViewRight ViewFront ViewScanningTo scan bar codes:1. Set the RFD8500 to bar code mode.2. Aim the device at the bar code.3. Press the trigger on the handle. The scan/decode LED lights, and a beep sounds to indicate a successful decode. For more information, refer to the User Guide at: www.zebra.com/support. Preliminary500 Software on Mobile Computee RFD8500 with a mobile computer, software installaload the software file from theb site: www.zebra.com/supons pSyncGETTING uter. Used for all RFID operations, the RFD8500 increaseusing the mobile computer in scan-intensive applications fords ofRgmovRegulatoryryyyyy yyyryryyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyatoryatoraatorytoatorroroooaoratoratortortortttttotototototototottttttttttototototootoooatatatattttttototttttototototooatatatattttttototttttotototototoatatatatatatttttatatttttatatatatatatatatttatatatattttotototoatoatoaatataaaaaaataaaaaaatatatataaaaattatttotootortoorororororrroooorrrrrrtortororrrrrrortorrorooororraaaaaaaaaaaaaayyND SCANmoving the Mobile Computer from the RFD8DraftATIOftattery of a morecommended formge/communication ca
AVOID EXTREME WRIST ANGLESAVOID EXTREME WRIST ANGLESAVOID EXTREME WRIST ANGLES012345012345ACCESSORIESRFD8500 Quick Start GuideXXXXXXXX Beta Draft — May 2015AVOID EXTREME WRIST ANGLEShttp://www.zebra.com/RFD8500REMOVING THE BATTERY COVERMore Information on the RFD8500For the latest version of this guide and related product information, visit the Zebra Web site at: http://www.zebra.com/support.Service Before you use the unit, it must be configured to operate with your mobile deviceto run your applications. If you have a problem running your equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact Zebra support at: http://www.zebra.com/support. WarrantyFor the complete Zebra hardware product warranty statement, go to: http://www.zebra.com/warranty.Zebra Technologies CorporationLincolnshire, IL U.S.A.Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.© 2015 Symbol Technologies, Inc.Charge Only Cable USB/Charge CableFive-slot Charge Only CradleNote: The RFD8500 can charge without the mobile computer attached. RFID OperationOPTIMUM RFID TAG DECODINGOPTIMUM RFID BODY POSTUREAVOID EXTREMEWRIST ANGLESfor High ScanningAVOID REACHINGAVOID BENDINGOptimum Body PostureOptimum Body Posturefor Low Scanning Optimum UprightBody Posture Optimum Scanning PositionsUse a ladderTaking breaks and task rotation recommended Alternate left and right handNote: Alternate left and right hands. Taking breaks and task rotation recommended.CORRECTWRONGPush InSlide OffPAIRINGPairing with an Android DeviceTo pair with an Android device such as the TC55:1. Power on the TC55.2. Touch the Settings icon.3. Turn Bluetooth on.4. Touch Bluetooth to display the AVAILABLE DEVICES list.5. Turn the RFD8500 on.6. Ensure Bluetooth is enabled on the RFGD8500. If not, press the Bluetooth button on the RFD8500 until the Bluetooth indicator blinks blue.7. The RFD8500 device displays in the list of AVAILABLE DEVICES.8. Tap the RFD8500 device in the list and press the RFD8500 trigger to pair.9. Exit the Bluetooth screen and run the RFID demo application.10. Go to Settings > Readers List and select the RFD8500 in the list of Available Readers. This connects the RFD8500 to the mobile device.Preliminaryttonthe list and press the RFD8500 trigger to pair.oth screen and run the RFID demo application.> Readers List and select the RFD8500 in the list of Available Readershe RFD8500 to the mobile device.RegulRRRRRRRRRRRRRRRRRRRRReReReReReeeeeg5RRRatory atoatoatoatoatooooooooooootototottottooatoatoatoaaaaayyyyyyyBODY POptimum Scanning PositionsDraftDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDDftftttttfttftftftftftftftttfttftfttftftftftftftftftftfttafftaftftafth Scanningm Body Po
Zebra reserves the right to make changes to any product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Zebra products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Zebra products.WarrantyFor the complete Zebra hardware product warranty statement, go to:http://www.zebra.com/warranty.For Australia OnlyThis warranty is given by Zebra Technologies Asia Pacific Pte. Ltd., 71 Robinson Road, #05-02/03, Singapore 068895, Singapore. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Zebra Technologies Corporation Australia’s limited warranty above is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Zebra Technologies Corporation at +65 6858 0722. You may also visit our website: http://www.zebra.com for the most updated warranty terms.RFD8500REGULATORY GUIDEZebra Technologies CorporationLincolnshire, IL U.S.A.http://www.zebra.comZebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.© 2015 Symbol Technologies, Inc.MN002062A01 Revision 2 — May 2015Regulatory InformationThis guide applies to the following Model Numbers: RFD8500. All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required. Local language translations are available at the following website:http://www.zebra.com/support.Any changes or modifications to Zebra equipment, not expressly approved by Zebra, could void the user's authority to operate the equipment.Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations.CAUTION: Only use Symbol approved and UL Listed accessories, battery packs and battery chargers.Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be dry before connecting to an external power source.Declared maximum operating temperature: 40°C.Bluetooth® Wireless TechnologyThis is an approved Bluetooth® product. For more information or to view End Product Listing, please visit:https://www.bluetooth.org/tpg/listings.cfm.Wireless Devices Country ApprovalsRegulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe.Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at:http://www.zebra.com/docNote: Europe includes Austria, Belgium, Bulgaria, Croatia, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.Health and Safety RecommendationsErgonomic Recommendations• Reduce or eliminate repetitive motion• Maintain a neutral postures• Reduce or eliminate excessive force• Keep objects that are used frequently within easy reach• Perform tasks at correct heights• Reduce or eliminate vibration• Reduce or eliminate direct pressure• Provide adjustable workstations• Provide adequate clearance• Provide a suitable working environment• Improve work procedures.Please observe all warning notices with regard to the usage of wireless devices.Wireless devices transmit radio frequency energy and may affect medical electrical equipment.Wireless devices should be switched off wherever you are requested to do so in hospitals, clinics or healthcare facilities. These requests are designed to prevent possible interference with sensitive medical equipment.PacemakersPacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a hand-held wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research.Persons with Pacemakers:• Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.• Should not carry the device in a breast pocket.• Should use the ear furthest from the pacemaker to minimize the potential for interference.• If you have any reason to suspect that interference is taking place, turn OFF your device.Other Medical DevicesPlease consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.Safety InformationReducing RF Exposure - Use Properly Only operate the device in accordance with the instructions supplied.InternationalThe device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on "International" human exposure to electromagnet fields refer to the Zebra Declaration of Conformity (DoC) at http://www.zebra.com/doc located under Wireless Communications and Health.For further information on the safety of RF energy from wireless devices seehttps://www.zebra.com/us/en/about-zebra/company-information/corporate-responsibility.html.EuropeHand-held Devices To comply with EU RF exposure requirements, this device must be operated in the hand with a minimum separation distance of 23cm or more from a person's body. Other operating configurations should be avoided.US and CanadaCo-located statementTo comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling.Hand-held DevicesTo comply with FCC RF exposure requirements, this device must be operated in the hand with a minimum separation distance of 23 cm or more from a person's body. Other operating configurations should be avoided.Industry Canada Statement:IMPORTANT NOTE: Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 23cm between the radiator and your body.NOTE IMPORTANTE: Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 23 cm de distance entre la source de rayonnement et votre corps.To satisfy FCC RF exposure requirements, a mobile transmitting device must operate with a minimum separation distance of 23 cm or more from a person's body.LED DevicesLED Compliance Statement:Classified as "EXEMPT RISK GROUP" according to IEC 62471:2006 and EN 62471:2008Pulse duration: xx ms Power SupplyUse ONLY a Symbol approved UL LISTED ITE (IEC/EN 60950-1, LPS) power supply with electrical ratings: Output 5Vdc, min 1.2A, with a maximum ambient temperature of at least 50 degrees C. Use of alternative power supply will invalidate any approvals given to this unit and may be dangerous.BatteriesTaiwan - RecyclingEPA (Environmental Protection Administration) requires dry battery producing or importing firms in accordance with Article 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in sales, giveaway or promotion. Contact a qualified Taiwanese recycler for proper battery disposal.Battery InformationUse only Symbol approved batteries. Accessories which have battery charging capability are approved for use with the following battery models:Symbol 82-172087-01 (3.7Vdc, 4410 mAh)Symbol rechargeable battery packs are designed and constructed to the highest standards within the industry.However, there are limitations to how long a battery can operate or be stored before needing replacement. Many factors affect the actual life cycle of a battery pack, such as heat, cold, harsh environmental conditions and severe drops.When batteries are stored over six (6) months, some irreversible deterioration in overall battery quality may occur. Store batteries at half of full charge in a dry, cool place, removed from the equipment to prevent loss of capacity, rusting of metallic parts and electrolyte leakage. When storing batteries for one year or longer, the charge level should be verified at least once a year and charged to half of full charge.Replace the battery when a significant loss of run time is detected.Standard warranty period for all Symbol batteries is 30 days, regardless if the battery was purchased separately or included as part of the mobile computer or bar code scanner. For more information on Symbol batteries, please visit:https://atgsupportcentral.motorolasolutions.com/content/emb/docs/MCS/batbasics1.pdf.Battery Safety Guidelines• The area in which the units are charged should be clear of debris and combustible materials or chemicals. Particular care should be taken where the device is charged in a non commercial environment.• Follow battery usage, storage, and charging guidelines found in the user's guide.• Improper battery use may result in a fire, explosion, or other hazard.• To charge the mobile device battery, the battery and charger temperatures must be between +32 ºF and +104 ºF (0 ºC and +40 ºC) • Do not use incompatible batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact Symbol support.• For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.• Do not disassemble or open, crush, bend or deform, puncture, or shred.• Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.• Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.• Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.• Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.• Battery usage by children should be supervised.• Please follow local regulations to promptly dispose of used re-chargeable batteries.• Do not dispose of batteries in fire.• Seek medical advice immediately if a battery has been swallowed.• In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with large amounts of water and seek medical advice.• If you suspect damage to your equipment or battery, contact Symbol support to arrange for inspection.Radio Frequency Interference Requirements-FCCNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected• Consult the dealer or an experienced radio/TV technician for help.Radio Transmitters (Part 15)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Radio Frequency Interference Requirements - CanadaCAN ICES-3 (B)/NMB-3(B)This device is in compliance with the NRC for Industry Canada applicable to license-exempt radios. Use is allowed with the following two conditions: (1) the device must not produce interference, and (2) the device must accept any interference to the radio, even if the interference is likely to compromise operation.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications were met.Bluetooth® Wireless Technology for use through the EEA has the following restrictions:• Maximum radiated transmit power of 100mW EIRP in the frequency range 2.400 -2.4835 GHz.RFID devices for use through the EEA have the following restrictions:• Maximum radiated transmit power of 2W ERP in the frequency range 865.6-867.6MHzThe use of RFID Devices has varying restrictions for use within the EEA; please refer to the Zebra Declaration of Conformity (DoC) for details at: http://www.zebra.com/doc.Statement of ComplianceSymbol hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and 2011/65/EU. A Declaration of Conformity may be obtained from: http://www.zebra.com/doc.Operation of the device without regulatory approval is illegal.CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.Warnings for Use of Wireless DevicesSafety in HospitalsRF Exposure GuidelinesCAUTION Risk of explosion if battery is replaced by an incorrect type.Dispose of batteries according to instructions.Marking and European Economic Area (EEA)
Waste Electrical and Electronic Equipment (WEEE)English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee.Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez : www.zebra.com/weee.Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: www.zebra.com/weee.Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter www.zebra.com/weee.Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: www.zebra.com/weee.Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: www.zebra.com/weee.Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee voor meer informatie over het terugzenden van producten.Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej www.zebra.com/weee.eština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: www.zebra.com/weee.Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: www.zebra.com/weee.Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a www.zebra.com/weee weboldalra.Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o vraèilu izdelka obišèite: www.zebra.com/weee.Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du returnerar produkten finns på www.zebra.com/weee.Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa www.zebra.com/weee.Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: www.zebra.com/weee.:    ..:   ,      ,     Zebra  .         ,    www.zebra.com/weee  .Malti: Gal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aar tal-ajja ta' l-uu taghom, iridu jiu rritornati gand Zebra gar-riikla. Gal aktar tagrif dwar kif gandek tirritorna l-prodott, jekk jogbok ur: www.zebra.com/weee.Slovenina: Pre zákazníkov z krajín EU: Všetky výrobky musia by po uplynutí doby ich životnosti vrátené spolonosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: www.zebra.com/weee.Lietuvi: ES vartotojams: visi gaminiai, pasibaigus j eksploatacijos laikui, turi bti gržinti utilizuoti  kompanij „Zebra“. Daugiau informacijos, kaip gržinti gamin, rasite: www.zebra.com/weee.Latviešu: ES klientiem: visi produkti pc to kalpošanas mža beigm ir jnogd atpaka Zebra otrreizjai prstrdei. Lai iegtu informciju par produktu nogdšanu Zebra, ldzu, skatiet: www.zebra.com/weee.Türkçe: AB Müterileri için: Kullanm süresi dolan tüm ürünler geri dönütürme için Zebra'ya iade edilmelidir. Ürünlerin nasl iade edilecei hakknda bilgi için lütfen u adresi ziyaret edin: www.zebra.com/weee.Turkish WEEE Statement of ComplianceEEE Yönetmeliine UygundurChina RoHSThis table was created to comply with China RoHS requirements.???Space holder for chartService InformationIf you have a problem using the equipment, contact your facility’s Technical or Systems Support. If there is a problem with the equipment, they will contact the Global Support Center at: http://www.zebra.com/support.For the latest version of this guide go to: http://www.zebra.com\support.

Navigation menu