Zebra Technologies RFID-CPMFS-02 Contactless Encoder Module User Manual

Zebra Technologies Corporation Contactless Encoder Module

User Manual

Download: Zebra Technologies RFID-CPMFS-02 Contactless Encoder Module User Manual
Mirror Download [FCC.gov]Zebra Technologies RFID-CPMFS-02 Contactless Encoder Module User Manual
Document ID3119883
Application IDj1BldoSWUCP3Eds7t7pHZA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize58.14kB (726768 bits)
Date Submitted2016-09-01 00:00:00
Date Available2017-02-28 00:00:00
Creation Date2013-09-19 08:20:29
Producing SoftwareAcrobat Distiller 7.0.5 (Windows)
Document Lastmod2016-09-01 07:31:49
Document TitleMicrosoft Word - M6e-Micro Installation Guide 9-19-13.docx
Document CreatorPScript5.dll Version 5.2.2
Document Author: gmedina

Installation Guide
Contactless Encoder
CPMFS02
Radio Module
Compliance and Regulatory Statements
FCC Compliance Statement (USA)
This device complies with Part 15 rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for Class B Digital Devices,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a residential environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the product manuals, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, the
user is encouraged to do one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced RF service technician for help.
The end product must be labeled, in a visible area, with the following:
Contains FCC ID: I28RFID-CPMFS-02
Modification Warning
The user is cautioned that any changes or modifications not expressly approved by Zebra
Technologies could void the user’s authority to operate the equipment. To ensure compliance, this
printer must be used with fully shielded communication cables.
RF Exposure Statement
This transmitter complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter, except in accordance with FCC multi- transmitter product
procedures.
Canadian DOC Compliance Statement
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada. This Class B digital apparatus complies with Canadian ICES-003.
Industry Canada (IC) Warning
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1)
l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: 1) This device may not cause interference., 2)
This device must accept any interference, including interference that may cause undesired
operation of the device.
The end product must be labeled, in a visible area, with the following:
Contains IC: 3798B-CPMFS02
Approved Antenna information
Only Zebra approved antennas are allowed and cannot be user
replaceable.
Antenna Type:
PCB: Gain: -20 dBi
General
The Contactless Encoder CPMFS02 radio module has been certified as a LMA. Additional evaluation is
required for use in all host devices. The following describes the installation procedures for the various
hosts in which the module has been evaluated.
Installation Instructions for Zebra printers
The Contactless Encoder radio module is not intended for OEM Integrators or end users. It can only
be installed at the grantee manufacturing facility.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 4
XMP Toolkit                     : NitroPro 9.5
Modify Date                     : 2016:09:01 07:31:49-05:00
Title                           : Microsoft Word - M6e-Micro Installation Guide 9-19-13.docx
Creator                         : PScript5.dll Version 5.2.2
Create Date                     : 2013:09:19 08:20:29-05:00
Author                          : gmedina
Producer                        : Acrobat Distiller 7.0.5 (Windows)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: I28RFID-CPMFS-02

Navigation menu