Zebra Technologies RFID-R4CXNG-01 P4T with Zcomax WiFi plus RFID radio User Manual 3 of 3

Zebra Technologies Corporation P4T with Zcomax WiFi plus RFID radio 3 of 3

User Manual 3 of 3

P4T/RP4TUser Guide 30Bluetooth ZBR4 RadioThe following section only applies when the Bluetooth ZBR4 module is installed in a P4T series printer. This radio conguration has demonstrated compliance to FCC regulations. P4T series printers with this conguration sold in North America will have the FCC ID: I28-MD-ZBR4WA and the Industrie Canada ID: 3798B-ZBR4WA for this radio module on a label on the back of the printer. Caution • Exposure to Radio Frequency Radiation. The radiated output power of this internal Bluetooth radio is far below the FCC radio frequency exposure limits. The internal Bluetooth radio operates within guidelines found in radio frequency safety standards and recommendations. Do not use the printer in an unauthorized manner. Note • The following section only applies when the ZBR4 Bluetooth Radio is installed in a P4T Series printer. Unless specified elsewhere in this manual, the antenna used for this transmitter must not be co-located or must not operate in conjunction with any other antenna.European Regulatory Information for the ZBR4 Bluetooth RadioThis device is intended for use in all EU and EFTA member states.Europe – EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of compliance with the R&TTE Directive 1999/5/EC: • EN 60950-1 Safety of Information Technology Equipment • EN 300 328-2 Technical requirements for spread-spectrum radio equipment • EN 301 489-1/-17 EMC requirements for spread-spectrum radio equipment.This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and office use in all EU and EFTA member states.WLAN Module Using 802.11b/g Radio The following section only applies when the 802.11b/g WLAN module is installed in a P4T series printer. Other than conditions specied elsewhere in this manual, only one of the radio options can be installed in the printer at one time and the antenna used for these transmitters must not be co-located or must not operate in conjunction with any other antenna.P4T Series printers for sale in North America will have the 802.11b/g radio FCC ID: 128-PLAN11BG or FCC ID: I28MD-CXLAN11G, and the Industrie Canada ID: 3798B-PLAN11BG or Industrie Canada ID: 3798B-CXLAN11G printed on a label on the back of the unit. Caution • The radiated output power of this internal 802.11b/g WLAN radio is far below the FCC radio frequency exposure limits. The internal radio operates within guidelines found in radio frequency safety standards and recommendations. Do not use the printer in an unauthorized manner. Caution • Use of a P4T printer with the radio module marked with FCC ID: 128-PLAN11BG or FCC ID: I28MD-CXLAN11G meets the FCC requirements for radio frequency (RF) radiation exposure in the standard body worn conguration with no minimum separation. In this conguration, which applies whether the belt clip or shoulder strap is used, the face of the printer from which paper is transported is facing away from the user’s body. The standard conguration must always be used when the printer is body worn.Industry Canada (IC) WarningThis device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:1) This device may not cause interference.2) This device must accept any interference, including interference that may cause un-desired operation of the device.European Regulatory Information for this RadioAT BE CY CZ DKEE FI FR DE GRHU IE IT LV LTLU MT NL PL PTSK SI ES SE GBNote: -Member states in the EU with restrictive use for this device are crossed out!This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)Important Notice:This device is a portable RF printer intended for commercial and industrial use in all EU and EFTA member states. Important Notice:This device is a portable RF printer intended for commercial and industrial use in all EU and EFTA member states except in France where restrictive use appliesRadio Regulatory InformationSection ContinuesPrinter Preparation pg. 7Connecting the Printer pg. 26Radio Regulatory Information pg. 30RP4T Printers pg. 34 Maintenance pg. 35 Troubleshooting pg. 37Specications pg. 42 Appendices pg. 45 Index pg. 51P4T Overview- pg. 5Manual Introduction pg. 4
P4T/RP4TUser Guide 31Europe – EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of compliance with the R&TTE Directive 1999/5/EC: • EN55022European Emissions Standard • EN 60950-1Safety of Information Technology Equipment • EN 300 328-2 Technical requirements for spread-spectrum radio equipment • EN 301 489-17 EMC requirements for spread-spectrum radio equipment.This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and office use in all EU and EFTA member states, except in France where restrictive use applies.The use of this frequency band in France is subject to restrictions. You may only use channels 10 and 11 (2457 and 2462 MHz) on French territory, except in those French departments as listed in the table below where channels 1-13 (2412-2472 MHz) may be used. For more information see http://www.anfr.fr/ and/or http://www.art-telecom.fr01 Ain 36 Indre 69 Rhone02 Aisne 37 Indre et Loire 70 Haute Saone03 Allier 39 Jura 71 Saone et Loire05 Hautes Alpes 41 Loir et Cher 72 Sarthe08 Ardennes 42 Loire 75 Paris09 Ariege 45 Loiret 77 Seine et Marne10 Aube 50 Manche 78 Yvelines11 Aude 54 Meurthe et Moselle 79 Deux Sievres12 Aveyron 55 Meuse 82 Tarn et Garonne16 Charente 57 Moselle 84 Vaucluse19 Correze 58 Nievre 86 Vienne2A Corse Sud 59 Nord 88 Vosges2B Haute Corse 60 Oise 89 Yonne21 Cote d’Or 61 Orne 90 Territoire de Belfort24 Dordogne 63 Puy de Dome 91 Essonne25 Doubs 64 Pyrenees Atlantique 92 Hauts de Seine26 Drome 65 Hautes Pyrenees 93 Seine St Denis27 Eure 66 Pyrenees Orientales 94 Val de Marne32 Gers 67 Bas Rhin35 Ille et Vilaine 68 Haute RhinRepublic of China Regulatory Information for the 802.11b/g Radio經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。According to “Administrative Regulations on Low Power Radio Waves Radiated Devices” Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to a approved low power radio-frequency devices. The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If found, the user shall cease operating immediately until no interference is achieved. The said legal communications means radio communications is operated in compliance with the Telecommunications Act.The low power radio-frequency devices must be susceptible with the interference from legal communications or ISM radio wave radiated devices.NCC (Taiwan) Compliance Statement “經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信 ；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學 醫療用電波輻射性電機設備之干擾。”KC (Korea) Compliance StatementFor 2.4 GHz Radio device:For Class B Equipment 이 기기는 가정용(B급)으로 전자파적합등록을 한 기기로서주로 가정에서 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. Section ContinuesPrinter Preparation pg. 7Connecting the Printer pg. 26Radio Regulatory Information pg. 30RP4T Printers pg. 34 Maintenance pg. 35 Troubleshooting pg. 37Specications pg. 42 Appendices pg. 45 Index pg. 51P4T Overview- pg. 5Manual Introduction pg. 4
P4T/RP4TUser Guide 32802.11b/g and Bluetooth Co-located Radio ModulesThe following section only applies when the CF (Compact Flash) WLAN module and Bluetooth ZBR4 module are installed in a P4T printer. This co-located radio conguration has demonstrated compliance to FCC regulations. P4T printers with this conguration sold in North America will have the FCC ID: I28-ZB4LAN-01 and the Industrie Canada ID: 3798B-ZB4LAN01 for this radio conguration printed on a label on the back of the printer. Caution • Use of a P4T printer with the co-located ZBR4 Bluetooth radio module and the 802.11b/g WLAN radio module meets the FCC requirements for radio frequency (RF) radiation exposure in the standard body worn configuration with no minimum separation. In this configuration, which applies whether the belt clip or shoulder strap is used, the face of the printer from which paper is transported is facing away from the user’s body. The standard configuration must always be used when the printer is body worn. The radiated output power of this radio configuration is far below the FCC radio frequency exposure limits. Both the internal Bluetooth and the 802.11b/G radio operate within guidelines found in radio frequency safety standards and recommendations. Do not use the printer in an unauthorized manner. RP4T printers are not congured with this radio option.European Regulatory Information for the Compact Flash 802.11b Radio and Bluetooth Co-located Radio ModulesAT BE CY CZ DKEE FI FR DE GRHU IE IT LV LTLU MT NL PL PTSK SI ES SE GBNote: -Member states in the EU with restrictive use for this device are crossed out!This device is also authorized for use in all EFTA member states (CH, IS, LI, NO)Europe – EU Declaration of ConformityThis device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of compliance with the R&TTE Directive 1999/5/EC: • EN 60950-1Safety of Information Technology Equipment • EN 300 328-2 Technical requirements for spread-spectrum radio equipment • EN 301 489-17EMC requirements for spread-spectrum radio equipment.This device is a 2.4 GHz wireless LAN transceiver, intended for indoor home and office use in all EU and EFTA member states, except in France where restrictive use applies.The use of this frequency band in France is subject to restrictions. You may only use channels 10 and 11 (2457 and 2462 MHz) on French territory, except in those French departments as listed in the table below where channels 1-13 (2412-2472 MHz) may be used. For more information see http://www.anfr.fr/ and/or http://www.art-telecom.fr01 Ain 36 Indre 69 Rhone02 Aisne 37 Indre et Loire 70 Haute Saone03 Allier 39 Jura 71 Saone et Loire05 Hautes Alpes 41 Loir et Cher 72 Sarthe08 Ardennes 42 Loire 75 Paris09 Ariege 45 Loiret 77 Seine et Marne10 Aube 50 Manche 78 Yvelines11 Aude 54 Meurthe et Moselle 79 Deux Sievres12 Aveyron 55 Meuse 82 Tarn et Garonne16 Charente 57 Moselle 84 Vaucluse19 Correze 58 Nievre 86 Vienne2A Corse Sud 59 Nord 88 Vosges2B Haute Corse 60 Oise 89 Yonne21 Cote d’Or 61 Orne 90 Territoire de Belfort24 Dordogne 63 Puy de Dome 91 Essonne25 Doubs 64 Pyrenees Atlantique 92 Hauts de Seine26 Drome 65 Hautes Pyrenees 93 Seine St Denis27 Eure 66 Pyrenees Orientales 94 Val de Marne32 Gers 67 Bas Rhin35 Ille et Vilaine 68 Haute RhinSection ContinuesPrinter Preparation pg. 7Connecting the Printer pg. 26Radio Regulatory Information pg. 30RP4T Printers pg. 34 Maintenance pg. 35 Troubleshooting pg. 37Specications pg. 42 Appendices pg. 45 Index pg. 51P4T Overview- pg. 5Manual Introduction pg. 4
P4T/RP4TUser Guide 33RFID Encoder The following section only applies when the RFID encoder is in-stalled in an RP4T printer. The RFID encoder may be installed in con-junction with either the Bluetooth or 802.11g radio options detailed previously, but may not be installed with the Bluetooth/802.11g dual radio option.RP4T Series printers will have the fifth character of the Product Configuration Code (PCC), which determines country compatibility for the RFID encoder, per the following table:RFID option PCC digit “5” Printer ModelNo RFID 0 P4TUS U RP4TEU 1 RP4TAustralia 2 RP4TTaiwan 6 RP4TNew Zealand 8 RP4TBrazil 9 RP4TChina A RP4TMalaysia B RP4TPhillipines C RP4TIndia D RP4TEl Salvador E RP4TIsreal F RP4TJapan G RP4TKorea H RP4TThe following table lists FCC and Industrie Canada ID numbers for the various configurations of RP4T printer radio options. Conguration FCC ID: Industrie Canada ID:RFID Encoder I28RFID-M5ECZ-01 3798B-M5ECZ01 RFID Encoder & 802.11b/g Option K I28RFID-R4LANG-01 3798B-R4LANG01 RFID Encoder & 802.11b/g Option G 128RFID-R4CXNG-01 3798B-R4CXNG01RFID Encoder & BT2.0 Radio I28RFID-M5ZBR4-01 3798B-M5ZBR401 Caution • Exposure to Radio Frequency Radiation. The radiated output power of this RFID encoder is far below the FCC radio frequency exposure limits. The RFID encoder operates within guidelines found in radio frequency safety standards and recommendations. Do not use the printer in an unauthorized manner.Printer Preparation pg. 7Connecting the Printer pg. 26Radio Regulatory Information pg. 30RP4T Printers pg. 34 Maintenance pg. 35 Troubleshooting pg. 37Specications pg. 42 Appendices pg. 45 Index pg. 51P4T Overview- pg. 5Manual Introduction pg. 4

Navigation menu