Zebra Technologies SP5500 Pole Mounted Reader User Manual ET5X Enterprise Tablet Quick Reference Guide
Zebra Technologies Corporation Pole Mounted Reader ET5X Enterprise Tablet Quick Reference Guide
User manual
SP5500
Pole Mounted Reader
Regulatory Guide
2 SP5500 Pole Mounted Reader
© 2016 Symbol Technologies LLC, a subsidiary of Zebra Technologies
Corporation.
Warranty
For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty.
Service Information
If you have a problem using the equipment, contact your facility’s Technical or
Systems Support. If there is a problem with the equipment, they will contact the
Zebra Support at: http:www.zebra.com/support.
For the latest version of this guide go to: http://www.zebra.com/support.
Regulatory Guide 3
Regulatory Information
This guide applies to Model Number SP5500.
All Zebra devices are designed to be compliant with the rules and regulations in
the locations they are sold and will be labeled as required.
Any changes or modifications to Zebra equipment not expressly approved by
Zebra could void the user's authority to operate the equipment.
Zebra devices are professionally installed - the Radio Frequency Output Power
will not exceed the maximum allowable limit for the country of operation.
Antennas: Use only the supplied or an approved replacement antenna.
Unauthorized antennas, modifications, or attachments could cause damage and
may violate regulations.
The device is compliant with the following values and antenna characteristics:
Antennas
When using antennas not supplied by Zebra, the antennas must comply with all of
the appropriate specifications and criteria listed in the Regulatory Certification
table.
Wireless Device Country Approvals
Regulatory markings subject to certification are applied to the device signifying
the radio is approved for use in the following countries and continents: United
States and Canada.
Please refer to the Declaration of Conformity (DoC) for details of other country
markings. This is available at: http://www.zebra.com/doc.
Antenna Characteristic US & Canada
Max Conducted RF Power at Antenna Input + 27.0 dBm
Max Antenna Gain Allowed + 3dBil
Max Radiated Power Allowed 1W EIRP
Antenna Type Circular Polarized Patch
CAUTION Operation of the device without regulatory approval is illegal.
4 SP5500 Pole Mounted Reader
Country Selection - Worldwide Version Only
Select only the country in which the device will be used. Any other selection will
make the operation of this device illegal.
Please observe all warning notices with regard to the usage of wireless devices.
Potentially Hazardous Atmospheres - Fixed Installations
You are reminded of the need to observe restrictions on the use of radio devices
in fuel depots, chemical plants etc. and areas where the air contains chemicals or
particles such as grain, dust, or metal powders.
Wireless devices transmit radio frequency energy and may affect medical
electrical equipment. When installed adjacent to other equipment, it is advised to
verify that the adjacent equipment is not adversely affected.
Safety Information
Reducing RF Exposure - Use Properly
Only operate the device in accordance with the instructions supplied.
International
The device complies with internationally recognized standards covering human
exposure to electromagnetic fields from radio devices. For information on
“International” human exposure to electromagnetic fields refer to the Zebra
Declaration of Conformity (DoC) at http://www.zebra.com/doc.
For further information on the safety of RF energy from wireless devices, see
http://responsibility.zebra.com/index.php/downloads/ which is located under
Wireless Communications and Health.
Warnings for Use of Wireless Devices
Safety in Hospitals
RF Exposure Guidelines
Regulatory Guide 5
US and Canada
•Co-located statement
To comply with FCC RF exposure compliance requirement, the antenna used
for this transmitter must not be co-located or operating in conjunction with any
other transmitter/antenna except those already approved in this filling.
•Remote and Standalone Antenna Configurations
To comply with FCC RF exposure requirements, antennas that are mounted
externally at remote locations or operating near users at stand-alone desktop
or similar configurations must operate with a minimum separation distance of
23cm from all persons.
IMPORTANT NOTE
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 23cm between the radiator and your body.
NOTE IMPORTANTE
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être installé et
utilisé avec un minimum de 23 cm de distance entre la source de rayonnement et
votre corps.
Power Supply
This device must be powered from an 802.3at compliant power source which has
been certified by the appropriate agencies, or by a Zebra approved UL LISTED
ITE (IEC/EN60950-1) power supply with electrical ratings: output 24Vdc, min
3.25A, with a recommended ambient temperature of at least 40 degrees C. Use of
alternative power supply will invalidate any approvals given to this unit and may
be dangerous.
Use with Hearing Aids - FCC
When some wireless devices are used near some hearing devices (hearing aids
and cochlear implants), users may detect a buzzing, humming, or whining noise.
Some hearing devices are more immune than others to this interference noise,
and wireless devices also vary in the amount of interference they generate. In the
event of interference, you may want to consult your hearing aid supplier to discuss
solutions.
6 SP5500 Pole Mounted Reader
Radio Frequency Interference
Requirements - FCC
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Radio Frequency Interference
Requirements- Canada
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada's license-exempt RSSs. Operation is
subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Regulatory Guide 7
Label Marking: The Term 'IC:' before the radio certification only signifies that
Industry Canada technical specifications were met.
Etiquette de marquage: Le terme "IC" avant la certification radio signifie que le
produit est compatible avec le spécification Industrie Canada.
In accordance with the regulations of Industry Canada, this radio transmitter can
operate with an antenna of a type and a maximum gain (or lower) approved for
the transmitter by Industry Canada. With the aim of reducing the risk of radio
interference to other users, the chosen antenna type and its gain should be
selected so that the equivalent isotropically radiated power (e.i.r.p.) does not
exceed the intensity necessary for the establishment of a satisfactory connection.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio
peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radio électrique à l'intention des autres utilisateurs, il faut choisir le
type d'antenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une
communication satisfaisante.
This radio transmitter has been approved by Industry Canada to operate with the
antenna types listed below and having a maximum gain allowable and the
impedance required for each type of antenna. The antenna types not included in
this list, or whose gain is higher than the maximum gain indicates, are strictly
prohibited for the operation of the transmitter.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner
avec les types d'antenne énumérés ci-dessous et ayant un gain admissible
maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste ou dont le gain est supérieur au gain maximal indiqué,
sont strictement interdits pour l'exploitation de l'émetteur.
Circular polarized patch: +3dBil / 50ohms
Zebra Technologies Corporation
Lincolnshire, IL USA
http://www.zebra.com
Zebra and the stylized Zebra head are trademarks of ZIH Corp., registered in
many jurisdictions worldwide. All other trademarks are the property of their
respective owners.
© 2015 Symbol Technologies LLC, a subsidiary of Zebra Technologies
Corporation.
MN-002755-01 Rev. A - April 2016