Zebra Lp 2824 Z Users Manual

2824-Z to the manual 17fa5e28-25e8-4d56-a523-005481933775

2015-01-26

: Zebra Zebra-Zebra-Lp-2824-Z-Users-Manual-342327 zebra-zebra-lp-2824-z-users-manual-342327 zebra pdf

Open the PDF directly: View PDF .
Page Count: 62

Proprietary Statement
Preface
Contents
Introduction
- What’s in the Box?
- Inspecting the Printer
Getting Started
Operations & Options
Maintenance
Troubleshooting
Interfaces

Zebra® LP 2824-Z™

User Guide

Customer Order # 980531-001 A

The copyrights in this manual and the label printer described therein are owned by

Zebra Technologies. Unauthorized reproduction of this manual or the software in

the label printer may result in imprisonment of up to one year and fines of up to

$10,000 (17 U.S.C.506). Copyright violators may be subject to civil liability.

All product names and numbers are Zebra trademarks, and Zebra, the Zebra logo,

ZPL, ZPL II, ZebraNet, ZebraLink, are registered trademarks of ZIH Corp. All

rights reserved.

All other brand names, product names, or trademarks belong to their respective

holders.

980531-001 A LP 2824-Z User Guide 3

Proprietary Statement

This manual contains proprietary information of Zebra Technologies Corporation and its

subsidiaries (“Zebra Technologies”). It is intended solely for the information and use of parties

operating and maintaining the equipment described herein. Such proprietary information may

not be used, reproduced, or disclosed to any other parties for any other purpose without the

expressed written permission of Zebra Technologies.

Product Improvements

Continuous improvement of products is a policy of Zebra Technologies. All specifications and

designs are subject to change without notice.

FCC Compliance Statement

This device complies with Part 15 rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may

cause undesired operation.

This equipment has been tested and found to comply with the limits for Class B Digital

Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a residential

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the product manuals, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, the user is encouraged to do one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

4 LP 2824-Z User Guide 980531-001 A

Proprietary Statement

The user is cautioned that any changes or modifications not expressly approved by Zebra

Technologies could void the user’s authority to operate the equipment. To ensure compliance,

this printer must be used with Shielded Communication Cables.

Canadian DOC Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Liability Disclaimer

Zebra Technologies takes steps to ensure that its published Engineering specifications and

manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct

any such errors and disclaims liability resulting therefrom.

Limitation of Liability

In no event shall Zebra Technologies or anyone else involved in the creation, production, or

delivery of the accompanying product (including hardware and software) be liable for any

damages whatsoever (including, without limitation, consequential damages including loss of

business profits, business interruption, or loss of business information) arising out of the use

of, the results of use of, or inability to use such product, even if Zebra Technologies has been

advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion may

not apply to you.

980531-001 A LP 2824-Z User Guide 5

Preface

This section provides you with contact information, document structure and organization, and

additional reference documents.

Contacts

You can contact Zebra Technologies at any of the following:

Visit us at: www.zebra.com

Our Mailing Addresses:

Zebra Technologies Corporation

333 Corporate Woods Parkway

Vernon Hills, Illinois 60061.3109 U.S.A

Telephone: +1 847.634.6700

Fax: +1 847.913.8766

Zebra Technologies Europe Limited

Zebra House

The Valley Centre, Gordon Road

High Wycombe

Buckinghamshire HP13 6EQ, UK

Telephone: +44 (0)1494 472872

Fax: +44 (0)1494 450103

6 LP 2824-Z User Guide 980531-001 A

Preface

Environmental Management

Support

You can contact Zebra support at:

Web Address: www.zebra.com/SS/service_support.htm

US Phone Number +1 847.913.2259

UK/International Phone Number +44 (0) 1494 768289

Environmental Management

Document Conventions

The following conventions are used throughout this document to convey certain information:

Alternate Color (online only) Cross-references contain links to other sections in this guide.

If you are viewing this guide online, click the blue text to jump to its location.

Command Line Examples All command line examples appear in Courier New font.

For example, type the following to get to the Post-Install scripts in the bin directory:

Ztools

Files and Directories All file names and directories appear in Courier New font. For

example, the Zebra<version number>.tar file and the /root directory.

Cautions, Important, Note, and Example

Note • The web address is case-sensitive.

Do not dispose of this product in unsorted municipal waste. This product is recyclable, and

should be recycled according to your local standards.

For more information, please see our website at:

Web address: www.zebra.com/environment

Caution • Warns you of the potential for electrostatic discharge.

Caution • Warns you of a potential electric shock situation.

Preface

Related Documents

980531-001 A LP 2824-Z User Guide 9

Contents

Proprietary Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Environmental Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Document Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1 • Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

What’s in the Box? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Inspecting the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2 • Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Modes of Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Attaching Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Loading Roll Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Adjusting the Roll Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Placing the Roll in the Media Compartment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Adjusting the Guides. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Operator Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Printing a Test Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Hooking Up the Printer and Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Interface Cable Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Communicating with the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Adjusting the Print Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Adjusting the Print Quality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

10 LP 2824-Z User Guide 980531-001 A

Contents

3 • Operations & Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Thermal Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Replacing Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Printing in Peel-Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Printing on Fan-Fold Media. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Using the Cutter Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

4 • Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Print Head Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Media Path Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Platen Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Replacing the Platen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Replacing the Print Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Thermal-Transfer LP Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5 • Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Print Quality Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Manual Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Troubleshooting Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Printing a Configuration Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Recalibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Resetting the Factory Default Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Communications Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Feed Button Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6 • Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Universal Serial Bus (USB) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Parallel Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

ZebraNet® PrintServer II for Ethernet Networks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Serial (RS-232) Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

980531-001 A LP 2824-Z User Guide 11

Introduction

This section describes what you get in your shipping box and provides an overview of printer

parts. This section also has procedures that describe how to open and close the printer and

report any problems.

Hello!

Thank you for choosing a Zebra® desktop printer, a high-quality on-demand printer

manufactured by the industry leader in quality, service, and value—Zebra Technologies

Corporation. For over 25 years, Zebra Technologies Corporation has provided customers with

the highest caliber of products and support.

Your printer is a high-quality on-demand printer. The printer provides thermal-transfer

printing (which uses ribbon) and direct-thermal printing.

This manual provides all of the information you will need to operate your printer on a daily

basis. To create label formats, refer to your programming guide. This guide is available by

contacting your distributor or dealer.

Your printer, when connected to a host computer, functions as a complete system for printing

labels and tags.

Note • Many printer settings may also be controlled by your printer’s driver or label

preparation software. Refer to the driver or software documentation for more information.

12 LP 2824-Z User Guide 980531-001 A

Introduction

What’s in the Box?

Save the carton and all packing materials in case you need to ship or store the printer later.

After unpacking, make sure you have all parts. Follow the procedures for inspecting the

printer to familiarize yourself with printer parts so you can follow the instructions in this book.

Power Supply

and Cords

Documentation

and Warranty

Printer

Cleaning

Pen

Sample

Labels

Introduction

Inspecting the Printer

980531-001 A LP 2824-Z User Guide 13

Inspecting the Printer

Look at the outside of the printer and make sure that all parts are present.

Opening the printer

To access the media compartment, you must open the printer. Pull the release levers towards

you and lift the cover.

Interface

Connectors

(vary by option)

Feed

Button

Power

Switch Power

Supply

Receptacle

Status

Light

Release

Latches

14 LP 2824-Z User Guide 980531-001 A

Introduction

Inspecting the Printer

After opening the printer, check the media compartment.

Tear Bar

Print Head

Open-Hanger

Lock

Head-Up

Sensor

Peel-Off Option

Sensor

Roller

Bar

Platen

Roller

Media

Hangers

Media

Guides

Introduction

Inspecting the Printer

980531-001 A LP 2824-Z User Guide 15

Closing the printer

1. Hold the top cover and press the “kick-stand” cover lock to release.

2. Lower the top cover. The ribbon carriage automatically folds up into place.

3. Press down until the cover snaps closed.

Reporting Damage

If you discover damage or missing parts:

• Immediately notify and file a damage report with the shipping company. Zebra

Technologies Corporation is not responsible for any damage incurred during shipment of

the printer and will not cover the repair of this damage under its warranty policy.

• Keep the carton and all packing material for inspection.

• Notify the authorized reseller.

16 LP 2824-Z User Guide 980531-001 A

Introduction

Inspecting the Printer

980531-001 A LP 2824-Z User Guide 17

Getting Started

This section describes how to set up your printer for the first time and use the most common

operating procedures for loading media in tear-off mode and loading ribbon.

Modes of Printing

You can operate this printer in different modes:

• Standard tear-off mode allows you to tear off each label (or a strip of labels) after it is

printed.

• In optional peel-off mode, the backing material is peeled away from the label as it is

printed. After this label is removed, the next one is printed.

• In optional liner-free mode, labels have no backing. This option is only available with a

special platen.

• In optional cutter mode, an attached unit cuts through the media.

The printer typically uses roll media, but you can use fan-fold or other continuous media as

well.

For procedures to use optional modes and features, refer to the Operation and Options section.

18 LP 2824-Z User Guide 980531-001 A

Getting Started

Attaching Power Supply

Check the power supply to make certain it is appropriate for your input voltage.

1. Make sure the power switch is in the off position (forward).

2. The DC power supply has a barrel connector on one end that must be inserted into the

power supply receptacle on the back of the printer.

3. Insert the separate AC power cord into the power supply.

4. Plug the other end of the cord into an appropriate AC electrical outlet.

Caution • Use the power supply that came with your printer. Never operate the printer

and power supply in an area where they can get wet. Serious personal injury could result!

AC Power

Cord

Power

Indicator

Power

Supply

Receptacle

Power

Supply

Power

Switch

Barrel

Connector

Plug Varies

by Country

Getting Started

Loading Roll Media

980531-001 A LP 2824-Z User Guide 19

Loading Roll Media

When you load media, you must place the roll on the media hangers and then adjust the media

guides.

You must use the correct media for the type of printing you require. When printing without a

ribbon, you must use direct thermal media. When using ribbon, you must use thermal transfer

media. The printer's ribbon sensor detects motion of the supply spindle.

Adjusting the Roll Holders

Check the core of the media roll and adjust the holders if necessary.

• For a narrow core, lift the adjusters up.

• For a wide core, press the adjusters down.

20 LP 2824-Z User Guide 980531-001 A

Getting Started

Loading Roll Media

Placing the Roll in the Media Compartment

Whether your roll media is inside or outside wound you load it into the printer the same way.

1. Open the printer. Remember that you need to pull the release levers toward the front of

the printer.

2. Remove the outside length of media. During shipment, the roll may become dirty when

handled or dusty when stored. Removing the outside length avoids dragging adhesive or

dirty media between the print head and platen.

3. Separate and hold open the media hangers.

4. Orient the media roll so that its printing surface will be up as it passes over the platen.

5. Lower the roll between the hangers and close them onto the core.

Getting Started

Loading Roll Media

980531-001 A LP 2824-Z User Guide 21

Adjusting the Guides

The guides direct the media toward the platen and print head.

1. Thread the media through the guides. They should just touch the edges of the media.

2. Close the top cover. Remember that you need to lower the top cover and press down until

the latches snap into place.

22 LP 2824-Z User Guide 980531-001 A

Getting Started

Operator Controls

Power Switch

Press backward to turn ON or forward to OFF the printer.

Feed Button

• Tapping the Feed button forces the printer to feed one blank label.

• Holding the Feed button forces the printer to feed continuously.

• Pressing the Feed button takes the printer out of a “pause” condition. The printer is put

into “pause” by either a programming command or an error condition. See “What the

Status Light is Telling You” in the Troubleshooting chapter.

• Use the Feed button for printer setup and status (see “Feed Button Modes” in the

Troubleshooting chapter).

Status Light

Functions as a printer operational indicator (see “What the Status Light is Telling You” in the

Troubleshooting chapter).

Caution • The power should be turned off before connecting or disconnecting the

communications and power cables.

Status

Light

Feed

Button

Power

Switch

Getting Started

Printing a Test Label

980531-001 A LP 2824-Z User Guide 23

Printing a Test Label

Before you connect the printer to your computer, make sure that the printer is in proper

working order.

You can do this by printing a configuration label.

1. Make sure the media is properly loaded and the top cover of the printer is closed. Then,

turn the printer power on if you have not already done so.

2. When the status light is solid green, press and hold the feed button until the status light

flashes once.

3. Release the feed button. A configuration label will print.

If you cannot get this label to print, refer to the Troubleshooting chapter.

24 LP 2824-Z User Guide 980531-001 A

Getting Started

Hooking Up the Printer and Computer

Your printer will have one of these combinations of interfaces:

• Parallel

• Universal Serial Bus (USB) and DB-9 serial

• Ethernet and RJ-11 serial

Each specific interface option—USB, parallel, ethernet, serial—is discussed individually.

You must supply the required interface cable for your application.

Interface Cable Requirements

Data cables must be of fully shielded construction and fitted with metal or metalized connector

shells. Shielded cables and connectors are required to prevent radiation and reception of

electrical noise.

To minimize electrical noise pickup in the cable:

Keep data cables as short as possible (6’ [1.83 m] recommended).

Do not tightly bundle the data cables with power cords.

Do not tie the data cables to power wire conduits.

USB Interface Requirements

Universal Serial Bus (version 1.1) provides a high-speed interface that is compatible with your

existing PC hardware. USB’s “plug and play” design makes installation easy. Multiple

printers can share a single USB port/hub.

Parallel Interface Requirements

The required cable (IEEE 1284-compliant is recommended) must have a standard 36-pin

parallel connector on one end, which is plugged into the parallel port located on the back of the

printer. The other end of the parallel interface cable connects to the printer connector at the

host computer.

For pinout information, refer to Parallel Interface on page 56.

Caution • Keep the power switch in the OFF position when attaching the interface cable.

The power supply barrel connector must be inserted into the power supply receptacle on

the back of the printer before connecting or disconnecting the communications cables.

Important • This printer complies with FCC “Rules and Regulations,” Part 15, for Class B

Equipment, using fully shielded six-foot data cables. Use of longer cables or unshielded

cables may increase radiated emissions above the Class B limits.

Getting Started

Hooking Up the Printer and Computer

980531-001 A LP 2824-Z User Guide 25

Ethernet Interface Requirements

Ethernet provides a powerful networking capability that can be of use in a variety of internet/

intranet printing solutions. After you load media and close the top cover, you can press the test

button next to the connector on the rear of the printer to get an ethernet configuration label.

Serial Interface Requirements

The standard cable must have a nine-pin “D” type (DB-9P) male connector on one end, which

is plugged into the mating (DB-9S) serial port located on the back of the printer.

There is an optional serial interface that uses a 6-pin RJ-11 male connector on one end, which

is plugged into the mating RJ-11 alternative serial port located on the back of the printer.

The other end of the signal interface cable connects to a serial port at the host computer.

Depending on the specific interface requirements, this will most likely be a straight-through

cable.

For pinout information, refer to Serial (RS-232) Connector on page 58.

Communicating with the Printer

Universal Serial Bus (USB) Communications

The printer is a terminal device when using a universal serial bus interface. You can refer to

the Universal Serial Bus Specification for details regarding this interface.

Parallel Communications

When using the parallel port, typically there is no setup is required once the cable is plugged

in. If you should encounter any problems, consult the user’s guide that came with your

computer.

Internal ZebraNet® PrintServer II™ Ethernet Communications

You can refer to the ZebraNet® PrintServer II™ for Ethernet Networks Installation and

Operation Guide for details regarding this interface.

Serial Communications

Serial communications between the printer and the host computer can be set by either

autobaud synchronization or the ^SC command.

Autobaud

Autobaud synchronization allows the printer to automatically match the communication

parameters of the host computer. To autobaud:

1. Press and hold the feed button until the green status LED flashes once, twice, and then

three times.

2. While the status LED flashes, send a ZPL II format to the printer.

26 LP 2824-Z User Guide 980531-001 A

Getting Started

Adjusting the Print Width

3. When the printer and host are synchronized, the LED changes to solid green. (No labels

will print during autobaud synchronization.)

^SC Command

Use the Set Communications (^SC) command to change the communications settings on the

printer.

4. With the host computer set at the same communications settings as the printer, send the

^SC command to change the printer to the desired settings.

5. Change the host computer settings to match the new printer settings.

Refer to the ZPL II Programming Guide for more information about this command.

Default the Serial Parameters

To reset the communications parameters on the printer to the factory defaults (9600 baud, 8 bit

word length, no parity, 1 stop bit, and XON/XOFF), do the following:

6. Press and hold the feed button until the green status LED flashes once, twice, and then

three times.

7. While the status LED rapidly flashes amber and green, press the feed button.

Adjusting the Print Width

Print width must be calibrated when:

• You are using the printer for the first time.

• There is a change in the width of the media.

Print width may be set by way of the five-flash sequence in “Feed Button Modes” (see page )

or refer to the Print Width (^PW) command (consult your ZPL II Programming Guide).

Adjusting the Print Quality

Print quality is influenced by the heat of the print head, the speed of the media and the type of

media you are using. Only by experimenting will you find the optimal mix for your

application.

The relative darkness setting is controlled by either the six-flash sequence in “Feed Button

Modes” (see page ) or the Set Darkness (~SD) ZPL II command (follow the instructions in the

ZPL II Programming Guide).

If you find that the print speed needs to be adjusted, refer to the Print Rate (^PR) command in

the ZPL II Programming Guide.

980531-001 A LP 2824-Z User Guide 27

Operations & Options

This section helps you get the most from your printer.

You must use programming to control many of the printer’s functions.

For detailed information about creating labels using ZPL II, refer to the ZPL II Programming

Guide or visit our web site at www.zebra.com.

To improve print quality, changing both print speed and density may be required to achieve the

desired results. Your application’s printer driver provides control of the speed and heat

(density).

Example • The ~JL command controls label length.

The ^XA^JUS^XZ command saves the new settings to flash memory

28 LP 2824-Z User Guide 980531-001 A

Operations & Options

Thermal Printing

You must use the correct media for the type of printing you require. You must use direct

thermal media.

Caution • The print head becomes hot while printing. To protect from damaging the print

head and risk of personal injury, avoid touching the print head. Use only the cleaning pen

to perform maintenance.

Caution • The discharge of electrostatic energy that accumulates on the surface of the

human body or other surfaces can damage or destroy the print head or electronic

components used in this device. You must observe static-safe procedures when working

with the print head or the electronic components under the top cover.

Operations & Options

Replacing Supplies

980531-001 A LP 2824-Z User Guide 29

Replacing Supplies

If labels run out while printing, leave the printer power on while reloading (data loss results if

you turn off the printer). After you load a new ribbon roll, press the Feed button to restart.

Always use high quality, approved labels and tags. If adhesive backed labels are used that

don’t lay flat on the backing liner, the exposed edges may stick to the label guides and rollers

inside the printer, causing the label to peel off from the liner and jam the printer. Approved

supplies can be ordered from your dealer.

30 LP 2824-Z User Guide 980531-001 A

Operations & Options

Printing in Peel-Mode

The optional dispenser allows you to print in “peel-mode” where the label backing follows a

different path and the labels are presented one at a time for subsequent placement.

Before using peel-mode, you must send the programming commands to the printer.

^XA ^MMP ^XZ

^XA ^JUS ^XZ

Refer to your ZPL II Programmer’s Manual.

1. Remove several labels from the backing material.

2. Open the top cover.

3. Open the dispenser door.

4. Using a stylus, switch on the label-taken sensor.

5. Insert the backing in front of the peel bar and behind the peel roller.

6. Close the dispenser door.

7. Close the top cover.

8. Press the Feed button to advance the label.

9. During the print job, the printer will peel off the backing and present a single label. Take

the label from the printer so it will print the next label.

Operations & Options

Printing in Peel-Mode

980531-001 A LP 2824-Z User Guide 31

32 LP 2824-Z User Guide 980531-001 A

Operations & Options

Printing on Fan-Fold Media

Printing on fan-fold media requires you to set both the media hangers and the media guides in

position.

1. Open the top cover.

2. Open the hangers to their widest position.

3. Snap the holder-open lock towards the front of the printer.

4. With a sample of your media, adjust the guides to the width of the media. The guides

should just touch, but not restrict, the edges of the media.

5. Insert the media through the slot at the rear of the printer.

6. Run the media between the hangers and guides.

7. Close the top cover.

Operations & Options

Using the Cutter Option

980531-001 A LP 2824-Z User Guide 33

Using the Cutter Option

Printers that have a bezel with a motorized blade can dispense one or more forms that are then

automatically cut from the media supply. This option cuts through continuous paper from rolls

and liner between labels. Keep the cutter dry. Never use any solutions or solvents to clean the

blade.

Use the ^MM command to activate the cutter and the ^LL command to set the form length and

gap distance. See the ZPL II Programmer's Manual.

If the blade cuts through labels, adhesive can jam the cutter.

1. Turn OFF (O) printer power and unplug the power and interface cables before clearing the

cutter.

2. After removing debris, plug in the power and interface cables, turn on the printer, then test

for normal operation.

34 LP 2824-Z User Guide 980531-001 A

Operations & Options

Using the Cutter Option

980531-001 A LP 2824-Z User Guide 35

Maintenance

Cleaning

When you clean the printer, use one of the following supplies that best suits your needs:

The cleaning process takes just a couple of minutes using the steps outlined below.

Cleaning Supplies

Cleaning pens (12)

Cleaning swabs (25)

Printer Part Method Interval

Print head Let the print head to cool for a minute, then use a

new cleaning pen to swab the the thin gray line

on the print head from end to end.

NOTE: You do not have to turn off the printer to

do this.

When using direct

thermal: after every

roll of media.

Platen roller See “Platen Considerations” in the Maintenance

chapter. Manually rotate the platen roller. Clean

it thoroughly with 95% medical-grade alcohol

and a cleaning swab, cleaning card, or lint-free

cloth.

As needed.

Peel bar Clean it thoroughly with 95% medical-grade

alcohol and a cotton swab.

Let alcohol disappate and the printer dry

completely.

Tear bar

Media path

Exterior Water-dampened cloth.

Interior Brush or air blow.

Cutter Use tweezers to remove scraps.

36 LP 2824-Z User Guide 980531-001 A

Maintenance

Cleaning

Print Head Considerations

Always use a new cleaning pen on the print head (an old pen carries contaminants from its

previous uses that may damage the print head).

When you load new media, you can also clean the print head.

1. Rub the cleaning pen across the dark area of the print head.

2. Wait one minute before closing the printer.

Do not clean the platen roller.

Caution • Adhesives and coatings of media can over time transfer onto the printer

components along the media path including the platen and print head. This build-up can

accumulate dust and debris. Failure to clean the print head, media path and platen roller

could result in inadvertent loss of labels, label jams and possible damage to the printer.

Important • Using too much alcohol can result in contamination of the electronic components

requiring a much longer drying time before the printer will function properly.

Caution • The print head becomes hot while printing. To protect from damaging the print

head and risk of personal injury, avoid touching the print head. Use only the cleaning pen

to perform maintenance.

Maintenance

Cleaning

980531-001 A LP 2824-Z User Guide 37

Media Path Considerations

Use a cleaning swab or pen to remove debris, dust or crust that has built-up on the holders,

guides and media path surfaces.

1. Use the alcohol in the cleaning swab or pen to soak the debris so that it breaks up.

2. Wipe the knobs to remove accumulated debris.

3. Wipe the inside edges of both edge guides to remove any built-up residue.

4. Wait one minute before closing the printer.

Discard the cleaning swab or pen after use.

Edge

Guides

Knobs

Platen

38 LP 2824-Z User Guide 980531-001 A

Maintenance

Cleaning

Sensors

Dust can accumulate on the media and head-up sensors.

1. Gently blow away dust; if necessary, use a dry swap to brush away dust. If adhesives or

other contaminates remain, use an alcohol moistened swab to break up.

2. Use a dry swab several times to remove any residue that may be left from the first cleaning

Linerless Media

If you use linerless media in your application, sticky residue can build up quickly on the

media-path knobs and edge guides; dust and debris then accumulates in this sticky residue.

Make certain to clean these areas as needed.

Head-Up

Sensor

Media

Sensors

Maintenance

Lubrication

980531-001 A LP 2824-Z User Guide 39

Platen Considerations

The standard platen (drive roller) normally does not require cleaning. Paper and liner dust can

accumulate without effecting print operations. Contaminates on the platen roller can damage

the print head or cause the media to slip when printing. Adhesive, dirt, general dust, oils and

other contaminates should be cleaned immediately off the platen.

Keep a new platen available as a spare and install it whenever the printer has significantly

poorer performance, print quality or media handling. If sticking or jamming continues even

after cleaning, you must replace the platen.

The platen can be cleaned with a fiber-free swab (such as a Texpad swab) or a lint free, clean,

damp cloth very lightly moistened with medical grade alcohol (95% pure or better).

1. Open the media door and remove the media.

2. Remove the platen from the printer (see “Replacing the Platen” in this section).

3. Clean the platen surface with the alcohol moistened swab. Rotate the platen while

swabbing. Repeat this process two to three times with a new swab to remove residual

contaminates. Adhesives and oils, for example, may be thinned by the initial cleaning but

not completely removed.

4. Replace the platen in the printer (see “Replacing the Platen” in this section).

5. Discard the cleaning swab or pen after use.

Allow the printer to dry for one minute before loading labels.

Lubrication

Important • Cleaning shortens the life of non-stick platens user for linerless media. Cleaning

the non-stick platen removes the outer layer of non-stick material. You may need to feed over

three feet (a meter or more) of media to restore the non-stick properties.

Caution • No lubricating agents of any kind should be used on this printer. Some

commercially available lubricants, if used, will damage the finish and the mechanical parts

inside the printer.

40 LP 2824-Z User Guide 980531-001 A

Maintenance

Replacing the Platen

Removal

Open the printer and remove any media.

1. Using a pointed stylus, unhook the tabs on the right and left sides. Then rotate them

forward.

2. Lift the platen out of the printer’s bottom frame.

Assembly

Make sure the right bearing is on the shaft of the platen.

1. Align the platen with the gear to the left and lower it into the printer’s bottom frame.

2. Rotate the tabs back and snap them into place.

Tools • You will need to use a pointed stylus (such as tweezers, small slot-head screwdriver or

razor-knife during this procedure.

Maintenance

Replacing the Print Head

980531-001 A LP 2824-Z User Guide 41

Replacing the Print Head

In the event you need to replace the print head, read the procedure and review the removal and

installation steps before actually replacing the print head.

Caution • Prepare your work area by protecting against static discharge. Your work area

must be static-safe and include a properly grounded conductive cushioned mat to hold the

printer and a conductive wrist strap for yourself.

Caution • Turn the printer power off and unplug the power cord before replacing the print

head.

Tools • You will need to use a #1 Phillips driver during this procedure.

42 LP 2824-Z User Guide 980531-001 A

Maintenance

Replacing the Print Head

Thermal-Transfer LP Model

Before following the steps in this procedure, open the printer by pulling the release latches

forward then lifting the top cover.

Removal

1. Grasp the print head spring and pull it to the left; then, slide it free of the carriage.

2. Use the spring to pry the print head clip off the right side of the carriage.

3. Pull the print head and bracket forward.

4. Use a #2 Phillips driver to remove the screw that holds the ground wire.

5. Unplug both bundles of print head wires from their connectors.

A B

Maintenance

Replacing the Print Head

980531-001 A LP 2824-Z User Guide 43

Replacing the LP Print Head (Continued)

Assembly

1. Align the print head to plug the left and right connectors into the wire bundles.

2. Slip the ground wire under the right screw and use a #1 Phillips driver to tighten it.

3. Slide the print head into one side and jog it into the other side.

4. Align the pivots of the bracket onto the posts; then, snap the bracket into place.

5. Clean the print head with the cleaning pen.

Reload media. Plug in the power cord, turn on the printer and print a status report to ensure

proper function.

A B

44 LP 2824-Z User Guide 980531-001 A

Maintenance

Replacing the Print Head

980531-001 A LP 2824-Z User Guide 45

Troubleshooting

Resolutions

1. The printer is not receiving power.

• Have you turned on the printer power?

• Check power connections from the wall outlet to the power supply, and from the power

supply to the printer.

2. The printer is on and in an idle state.

No action necessary.

What the Status Light is Telling You

LED Status and Color Printer Status For a Resolution,

Refer to Number:

Off Off 1

Solid Green On 2

Flashing Amber Stopped 3

Flashing Green Normal Operation 4

Flashing Red Stopped 5

Double Flashing Green Paused 6

Solid Amber Various 7

Alternately Flashing Green and Red Needs Service 8

46 LP 2824-Z User Guide 980531-001 A

Troubleshooting

Resolutions

3. The printer has failed its power on self test (POST).

• If this error occurs right after you turn on the printer, contact an authorized reseller for

assistance.

There is a shortage of memory.

• If this error occurs after you have been printing, turn the printer power off and on. Then,

resume printing.

4. The printer is receiving data.

• As soon as all of the data has been received, the status LED will turn green; then, the

printer will automatically resume operation.

5. Either the media or ribbon is out.

• Load a roll of media, following the instructions in “Loading the Media” in the Getting

Started chapter. Then, press the feed button to resume printing.

• Load a roll of ribbon, following the instructions in “Loading the Ribbon” in the Getter

Started chapter. Then, press the feed button to resume printing.

The print head is open.

• Close the top cover. Then, press the feed button to resume printing.

6. The printer is paused.

• Press the feed button to resume printing.

Troubleshooting

Resolutions

980531-001 A LP 2824-Z User Guide 47

7. The print head is under temperature.

• Continue printing while the print head reaches the correct operating temperature.

The print head is over temperature.

• Printing will stop until the print head cools to an acceptable printing temperature. When it

does, the printer will automatically resume operation.

8. FLASH memory is not programmed.

• Return the printer to an authorized reseller.

48 LP 2824-Z User Guide 980531-001 A

Troubleshooting

Print Quality Problems

No print on the label.

• You must use the correct media for the method of printing you require. You must use

thermal transfer media.

• Is the media loaded correctly? Follow the instructions in “Loading the Media”in the

Getting Started chapter.

The printed image does not look right.

• The print head is dirty. Clean the print head.

• The print head is under temperature.

• Adjust the print darkness and/or print speed. Refer to the six-flash sequence in “Feed

Button Modes” later in this chapter, or the ^PR and ~SD commands in the ZPL II

Programming Guide.

• The media being used is incompatible with the printer. Be sure to use the recommended

media for your application, and always use Zebra-approved labels and tags.

There are long tracks of missing print (blank vertical lines) on

several labels.

• The print head is dirty. Clean the print head.

• The print head elements are damaged. Replace the print head (see “Replacing the Print

Head” in the Maintenance chapter).

The ribbon sensor settings did not print.

• The printer is set for direct thermal printing; use the ^XA^MTT^XZ command to reset the

printer for thermal transfer printing and calibrate again.

Troubleshooting

Print Quality Problems

980531-001 A LP 2824-Z User Guide 49

The printing does not start at the top of the label, or misprinting of

one to three labels.

• The media may not be threaded under the media guides. Refer to “Loading the Media” in

the Getting Started chapter.

• The printer needs to be calibrated. Refer to “Auto Calibration” in the Getting Started

chapter.

• The correct media sensor may not be activated. Manual calibration selects the media

sensing method for the labels being used (refer to the ^MN command in the ZPL II

Programming Guide).

• Verify that the Label Top (^LT) command is correctly set for your application (consult the

ZPL II Programming Guide).

A label format was sent to, but not recognized by, the printer.

• Is the printer in pause mode? If so, press the feed button.

• If the status LED is on or flashing, refer to “What the Status Light is Telling You” in this

chapter.

• Make sure the data cable is correctly installed.

• A communications problem has occurred. First, make sure that the correct

communications port on the computer is selected. Refer to “Communicating with the

Printer” in the Getting Started chapter.

50 LP 2824-Z User Guide 980531-001 A

Troubleshooting

Manual Calibration

Manual calibration is recommended whenever you are using pre-printed media or if the printer

will not correctly auto calibrate.

1. Make sure media is loaded.

2. Turn on the printer power.

3. Press and hold the feed button until the green status LED flashes once, then twice.

Release the feed button.

4. The printer will set the media sensor for the label backing being used. After it is done

making this adjustment, the roll will automatically feed until a label is positioned at the

print head.

5. A profile of the media sensor settings (similar to the example below) will print. Upon

completion, the printer will save the new settings in memory and the printer is ready for

normal operation.

6. Press the feed button. One entire blank label will feed. If this does not happen, try

defaulting (refer to the four-flash sequence in “Feed Button Modes” later in this chapter)

and recalibrating the printer.

Note • Performing a manual calibration disables the auto calibration function. To return to

auto calibration, default the printer (see the four-flash sequence in “Feed Button Modes” later

in this chapter).

Troubleshooting

Troubleshooting Tests

980531-001 A LP 2824-Z User Guide 51

Troubleshooting Tests

Printing a Configuration Label

To print out a listing of the printer’s current configuration, refer to the one-flash sequence in

“Feed Button Modes” later in this chapter.

Recalibration

Recalibrate the printer if it starts to display unusual symptoms, such as skipping labels. See

“Printing a Test Label” in the Getting Started chapter.

52 LP 2824-Z User Guide 980531-001 A

Troubleshooting

Resetting the Factory Default Values

Sometimes, resetting the printer to the factory defaults solves some of the problems. Follow

the four-flash sequence instructions in “Feed Button Modes” later in this chapter

Communications Diagnostics

If there is a problem transferring data between the computer and printer, try putting the printer

in the communications diagnostics mode. The printer will print the ASCII characters and their

respective hexadecimal values (a sample is shown below) for any data received from the host

computer. To find out how, refer to the power off mode procedure in “Feed Button Modes”

later in this chapter.

Troubleshooting

Feed Button Modes

980531-001 A LP 2824-Z User Guide 53

Feed Button Modes

Power Off Mode (Communications Diagnostics Mode)

With the printer power off, press and hold the feed button while you turn on the power. The printer prints out a listing of

its current configuration. After printing the label, the printer will automatically enter a diagnostic mode in which the

printer prints out a literal representation of all data subsequently received. To exit the diagnostic mode and resume

printing, turn off and then turn on the printer.

Power On Modes

With the printer power on and top cover closed, press and hold the feed button for several seconds. The green status

LED will flash a number of times in sequence. The explanation at the right (Action) shows what happens when you

release the key after the specific number of flashes

Flash Sequence Action

*A configuration label prints.

The media sensor calibrates and a media sensor profile prints (see “Manual Calibration”

earlier in this chapter).

***

To reset the communication parameters. Press and release the feed button while the LED

rapidly flashes amber and green.

For autobaud synchronization: Send a ZPL II format to the printer while the LED rapidly

flashes amber and green. When the printer and host are synchronized, the LED changes to

solid green. NOTE: No labels will print during autobaud synchronization.

***

****

Resets the factory defaults, auto calibrates, and saves settings into memory.

***

****

*****

The print width calibrates. While the status LED alternately flashes green and amber, a

series of stacking rectangles print on the label. When the rectangle prints to the outer

edges of the label, press and release the feed button. The label width and current

communication parameters will be saved into memory.

***

****

*****

******

The print darkness calibrates. A series of nine samples print, starting with the lightest and

ending with the darkest image. When the desired print darkness is achieved, press and

release the feed button. The print darkness will be saved into memory

If the feed button remains pressed after a 7-flash sequence, the printer will ignore the button when it is

released

54 LP 2824-Z User Guide 980531-001 A

Troubleshooting

Battery

The optional Real Time Clock requires a three-volt lithium battery on the main printed circuit

board. You can discern a low or flat battery if the printer provides a consistently delayed date

stamp. Only a qualified technician observing precautions against both static discharge and

electric shock can replace the battery.

Caution • Risk of explosion if battery is replaced with an incorrect type.

Important • Recycle batteries according to local your guidelines and regulations.

980531-001 A LP 2824-Z User Guide 55

Interfaces

Universal Serial Bus (USB) Connector

The figure below displays the cable wiring required to use the printer’s USB interface.

For printer supported operating systems and drivers, see the software and documentation CD

or visit the Zebra printer web site at:

www.zebra.com

For information on the USB interface, go to the USB web site at:

www.usb.org

Pin No. Description

1Vbus

2D–

3D+

4Ground

Shell Shield/Drain Wire

56 LP 2824-Z User Guide 980531-001 A

Interfaces

Parallel Interface

The maximum current available through the interface port is not to exceed a total of 0.75

amps.

Pin No. Description

1NStrobe/Host Clk

2-9 Data Bits 1-8

10 nACK/PtrClk

11 Busy/Per Busy

12 PError/ACK Dat Req.

13 Select/Xflag

14 NAuto Fd/Host Busy

15 Not Used

16-17 Ground

18 +5 V @ 0.75 A Fused

19-30 Ground

31 nInit

32 NFault/nData Avail.

33-34 Not Used

35 +5 V throught 1.8 K Ohms Resistor

36 NSelectin/1284 active

Interfaces

ZebraNet® PrintServer II for Ethernet Networks

980531-001 A LP 2824-Z User Guide 57

ZebraNet® PrintServer II for Ethernet Networks

This interface uses an RJ-45 straight-through cable type. The table below provides the pinout

assignments.

The figure above has the perspective looking into the printer RJ-45 modular connector.

You can refer to the ZebraNet® PrintServer IITM for Ethernet Networks Installation and

Operation Guide for details regarding this interface.

The RJ-11 jack on Ethernet boards is used for factory tests only.

Signal Pin Pin Signal

Tx+ 11Tx+

Tx- 22Tx-

Rx+ 33Rx+

--- 44---

--- 55---

Rx- 66Rx-

--- 77---

--- 88---

58 LP 2824-Z User Guide 980531-001 A

Interfaces

Serial (RS-232) Connector

The maximum current available through the serial and/or parallel port is not to exceed a total

of 0.75 Amps.

When XON/XOFF handshaking is selected, data flow is controlled by the ASCII control codes

DC1 (XON) and DC3 (XOFF). The DTR control lead will have no effect.

Interconnecting to DTE Devices —The printer is configured as data terminal equipment

(DTE). To connect the printer to other DTE devices (such as the serial port of a personal

computer), use an RS-232 null modem (crossover) cable.

Interconnecting to DCE Devices —When the printer is connected via its RS-232 interface to

data communication equipment (DCE) such as a modem, a STANDARD RS-232 (straight-

through) interface cable must be used.

Pin No. Description

1Not used

2RXD (receive data) input to the printer

3TXD (transmit data) output from printer

4DTR (data terminal ready) output from the printer -- controls when the

host may send data

5Chassis ground

6DSR (data set ready) input to the printer

7RTS (request to send) output from the printer -- always in the ACTIVE

condition when the printer is turned on

8CTS (clear to send) input to the printer

9+5 V @ 0.75 A fused

Interfaces

Serial (RS-232) Connector

980531-001 A LP 2824-Z User Guide 59

Connecting the Printer to a DTE Device

DB-25S

Connector

to DTE Device (PC)

DB-9P

Connector

to Printer

DB-9S

Connector

to DTE Device (PC)

DB-9P

Connector

to Printer

Connecting the Printer to a DCE Device

DB-25S

Connector

to DCE Device (PC)

DB-9P

Connector

to Printer

DB-9S

Connector

to DCE Device (PC)

DB-9P

Connector

to Printer

60 LP 2824-Z User Guide 980531-001 A

Interfaces

Serial (RS-232) Connector

Zebra Technologies Corporation

333 Corporate Woods Parkway

Vernon Hills, Illinois 60061.3109 U.S.A.

Telephone: +1 847.634.6700

Facsimile: +1 847.913.8766

Zebra Technologies Europe Limited

Zebra House

The Valley Centre, Gordon Road

High Wycombe

Buckinghamshire HP13 6EQ, UK

Telephone: +44 (0) 1494 472872

Facsimile: +44 (0) 1494 450103

Customer Order # 980531-001A

Zebra Lp 2824 Z Users Manual

2824-Z to the manual 17fa5e28-25e8-4d56-a523-005481933775

Navigation menu

Versions of this User Manual:

Views

Navigation