Zeeva TL-0021 Remote Controller of Drone User Manual TL 0021 Drone IM 19JUN17
Zeeva International Limited Remote Controller of Drone TL 0021 Drone IM 19JUN17
Zeeva >
User Manual
Product Overview Remote Control
Remote Control Batteries Installation
Drone Battery Charging
Package Contents
Remote control power supply: 3 x “AA” 1.5V Alkaline Batteries (Not Included)
Drone power supply: Rechargeable Li-ion Battery 3.7V
Charging time:1-2 hours
Play time: 6-7 minutes
Radio control type: RC model
Control distance: 70 Meters
Specification
Camera Photo / Video Instructions
Drone Accessories Assembly
Drone Accessories Assembly
Start off
Operation Method
Sensitivity Settings
Notice Care and Maintenance
Warning
Back
Front
BackFront
Please read this instruction manual carefully before operating the product.
Please do not operate the product in the gale.
The flying ground should be the local field and legal for remote control flying. Please do not operate the
product in forbidden zone or around people or animals.
Keep the aircraft a certain distance (at least 2-3 meters) from others when playing together.
Follow this Instruction can perform some 360-degree rolling action. In order to perform rolling action,
ensure to maintain the height of drone.
Under this advanced flight mode the drone is very fast and can perform a variety of tumbling instruction. You can
not perform rolling action when battery is low. Tap the "throttle joystick" back to normal mode.
Left side tumbling
Push the "Forward/Backward & Left/Right side joystick" toward the right, then quickly turn joystick to the
left, finally push the joystick back to the middle.
Right side tumbling
Push the "Forward/Backward & Left/Right side joystick" toward the left, then quickly turn joystick to the
right, finally push the joystick back to the middle.
Front rolling
Pull the "Forward/Backward & Left/Right side joystick" backward, then quickly lift the joystick toward to the
top, finally push the joystick back to the middle.
Backflip
Push the "Forward/Backward & Left/Right side joystick" front, then quickly lift the joystick backward, finally
push the joystick back to the middle.
The drone equipped four receivers for fault protection. When the drone is not received the remote control
signal, battery power failures or other failures, to ensure the motor does not start to achieve protection.
The drone have three operation modes: low, intermediate and advanced.
Tap the Forward/Backward & Left/Right side joystick enter setup mode
Turn on the remote control to enter the low axis mode (sensitivity up to 40%)
When the remote control to issue “DI” sound twice, axis into the intermediate mode (sensitivity up to 60%)
When the remote control to issue “DI” sound three times, axis into the advanced mode (sensitivity up to 100%)
The sensitivity can be adjusted by the fine-tuning button on the remote control, then press and hold the button
for one second to confirm or exit.
When all the of the basic movements are skilled, you can try to
perform some advanced action. Click on the rolling action button of
the remote control, the remote emits a continuous sound, the
drone will trun into the 3D rolling action mode.
Note: To avoid losing control, always pay attention when controlling the drone.
Turn on the power switch of drone, and place the drone on a flat
location, the status indicator start flashes, the gyroscope start
reading the midpoint.
Turn on the remote control power switch, push the Up/Down
joystick from the lowest to the highest, and then pull it down to
lowest position. Drone are ready for takeoff.
FCC Statement
This device complies with the part 15 of the FCC rules. Operation is subject to the following
two conditions:(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Caution: changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with instructions may cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on. The user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or experienced radio/ TV technician for help.
FCC ID: 2ADM5-TL-0021
This product is suitable to be used by people who has operating experience in flying model or aged no
less than 14 years old.
This product is not a toy but a precise equipment that integrating mechanics and electronics with expertise
of aerodynamics and high-frequency transmitting. It requires to be correctly assembled and debugged so
as to prevent the accident from being happened. The user should operate or control it in a safe way.
Please do not put the product in the mouth to prevent choking hazard of small parts.
Please do not put the finger into available interspaces.
Please do not play the product in a brutal way such as throwing, crashing or twisting it.
Please store the smaller-sized product accessories in places that are out of reach of children, in order to
avoid the occurrence of accidents.
The product is very powerful. For first time flight, it shall be observed that the joystick must be slowly
pushed in order to prevent the product from ascending too quickly and result in unnecessary collision and
damages.
When the flight is ended, the power supply of the remote control shall be switched off and then followed by
switching off the power supply of the product.
Avoid placing the batteries in places with high temperatures and exposure to heat.
When young children are operating the product, it shall be ensured that the adults are guiding and making
sure the product control is within the viewing range of the controller ( or instructor)such that it makes the
control very convenient.
When the product is not in use, please switch off the power supplies of both the aircraft and the remote
control, and remove the batteries in the remote control.
Please note that we won’t take any responsibility for any wrong operation as this may result in severe
injury or loss of property, and we cannot control the operating process during the time when the user
assemble or use this product.
Once this product is sold, we won’t be responsible for any safety responsibility during the time the user
operates or uses or controls this products.
Always use dry and soft cloth to clean this product.
Avoid this product to be exposed to sunlight or heat.
Avoid immersing these toys into water, otherwise, the electronic parts may be damaged.
Regularly check and inspect the plug and other accessories. If any damages are discovered, please
immediately stop using it, until it is completely repaired in good working condition.
1. TO AVOID BATTERY LEAKAGE
a. Always follow the instructions carefully. Use only batteries specified and be sure to insert
them
correctly by matching the + and - polarity markings.
b. Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline
batteries.
c. Remove exhausted or dead batteries from the product.
d. Remove batteries if product is not to be played with for a long time.
e. Do not short-circuit the supply terminals.
f. RECHARGEABLE BATTERIES: Do not mix these with any other types of batteries.
Always remove from the product before recharging.
Recharge batteries under adult supervision. DO NOT RECHARGE OTHER TYPES OF
BATTERIES.
2. Should this product cause, or be affected by, local electricl interference, move it away
from
other electrical equipment.Reset ( switiching off and back on again or removing and
re-inserting batteries) if necessary.
IMPORTANT: BATTERY INFORMATION
CAUTION:
OFF ON VIDEO
OFF ON VIDEO
OFF ON
VIDEO
OFF
ON VIDEO
Lowest Highest
OFF ON
VIDEO
Explorer Drone x 1
USB Charger x 1
Remote Control x 1
User Manual x 1
Propeller Guard x 4Landing Gear x 4
Camera x 1
Keep All Relevant Information for Future Reference
Power (Failure) program
Step 1:
Step 2:
Indicator
3D rolling action
Up/Down joystick
Turn Left/Right joystick Control drone left or right rotation
Control drone left or right lateral movement
Left traverse Right traverse
Control drone forward and backward movement
Left rotation
Right rotation
Forward
Backward
Control drone up and down
Instruction Manual
Drone
EXPLORER
Thank you for purchasing the explorer drone.
This manual provides more information about this drone,
please read the instructions before using.
14+ Antenna
Power ON/OFF
High/Low speed switch
Headless mode
One key return mode
Turn left
fine-tuning
Turn right
fine-tuning
Left side parallel
movement fine-tuning
Right side parallel
movement fine-tuning
Backward fine-tuning
Forward fine-tuning
Forward/Backward &
Left/Right side joystick
Rolling action button
Photo button
Video button
Light Control
Up/Down & Turn
Left/Right joystick
When inserting the batteries, you must
insert according to the correct polarity,
the remote wont function if batteries are
reversed.
Notice:
To install batteries into the controller,
unscrew the screw on the battery
box cover, to open the cover.
Insert 3 x “AA” batteries 1.5V Alkaline
Batteries (not included) into the battery box.
Batteries sould be placed as show on the diagram.
To recharge the battery of the drone, open battery box cover. Disconnect the rechargeable li-ion battery from the
drone. Connect and plug into the socket of USB charger for battery charging. Sould be placed as show on the
diagram. In the process of the battery charging, the indicator shows red light; after full charging, the indicator
light will turn off.
Propeller Guard: Insert four propeller guard into the holes of the propeller guard, and use the screwdriver
to lock four screws lightly.
Landing Gear: Insert the four landing gear into the landing gear holes at the bottom of the drone.
Camera: Insert camera stuck on fuselage buckle at the bottom of the drone. And plug the wire to the
video section.
Turn the drone power on, the camera ready when the RED indicator change from flasching to BLUE and
keep light on. If the RED indicator light on and light off for after few seconds, it means the SD card is not
in the camera. Please insert the SD card, than the indicator light will turn off.
Photo: Press the photo button from remote control, will issue a “DI” sound. The indicator light of camera
will flash one time, and take a photo.
Video: Press the video button from remote control and hold for several seconds, will issue continue “DI
DI DI” sound. The indicator light of the camera will be flashing, it will start recording video, press
the button again, the RED light turn BLUE, and the camera will stop recording.
3 x “AA” 1.5V Alkaline Batteries
(not included)
Forward/Backward joystick
Left/Right side joystick
Propeller Guard:
Landing Gear: Camera: