Zenith HCS5610 039A_080812 User Manual To The 0c76cd27 B64e 4428 807c D2c26d569651
User Manual: Zenith HCS5610 to the manual
Open the PDF directly: View PDF 
.
Page Count: 72
©Copyright 2008, LG Electronics U.S.A., Inc.
Installation and Operating Guide | Warranty
Model Number | HCS5610 | HD Integrator Box System
page 5
t a b l e o f c o n t e n t s
page 70
installer quick setup guide
Zenith and the lightning Z logo are registered
trademarks of Zenith Electronics Corporation
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED
SERVICE PERSONNEL.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
IT IS FORBIDDEN TO CONNECT THIS TV TO ANY TELECOMMUNICATION NETWORK / TELEPHONE.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
NOTE TO CABLE TV INSTALLER:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of
the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to
operate the equipment
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069.
For Customer Support/Service please call:
1-888-865-3026
www.zenith.com
www.lgcommercial.com
RECORD THE MODEL NUMBER
The model and serial number of this HD Integrator Box
System are located on the side of the cabinet. For future
reference, we suggest that you record the serial number here:
MODEL NO. HCS5610
SERIAL NO.____________________________________
PAGE 3
CAUTION:
Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation.
Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is:
LG Electronics U.S.A., Inc.,
2000 Millbrook Drive
Lincolnshire, IL 60069, USA.
Phone: 1-847-941-8000
WARNING:
Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the
apparatus.
CAUTION:
THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE
QUALIFIED TO DO SO.
CAUTION:
When used outside of the U.S., it may be used HAR cord with fitting of an approved agency is employed.
(When used outside of U.S., other power supply cords may be used if the cord is approved by the local regulating agency.)
DISCONNECTING DEVICE FROM MAINS:
Main plug is the disconnecting device. The plug must remain readily operable.
An apparatus with CLASS I construction shall be connected to a Mains socket outlet with a protective earthing connection.
IMPORTANT SAFEGUARDS FOR YOU AND YOUR NEW PRODUCT
YOUR PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH YOUR SAFETY IN MIND. HOWEVER, IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. TO AVOID DEFEATING THE SAFEGUARDS THAT HAVE BEEN BUILT INTO YOUR NEW
PRODUCT, PLEASE READ AND OBSERVE THE FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING YOUR NEW PRODUCT, AND SAVE
THEM FOR FUTURE REFERENCE. OBSERVING THE SIMPLE PRECAUTIONS DISCUSSED IN THIS MANUAL CAN HELP YOU GET MANY YEARS OF
ENJOYMENT AND SAFE OPERATION THAT ARE BUILT INTO YOUR NEW PRODUCT.
PAGE 4
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or object have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to
provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.),
ANSI/NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
Example of Grounding According to National Electrical Code Instructions
IMPORTANT SAFETY INSTRUCTIONS
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
Ground Clamp
Electric Service
Equipment
NEC - National Electrical Code
PORTABLE CART WARNING
Table of Contents
PAGE 5
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . .2-3
Important Safety Instructions . . . . . . . . . . . . . . . . . . .4
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Step 1. HD Integrator Box System Installation and
Connections
Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Installation/Connections Overview . . . . . . . . . . . . . . . .7
Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . .9
AUX Controller: Connection and Placement . . . . . . . . . .10
IR Receiver & IR Bracket Installation . . . . . . . . . . . . .10
TV and other Equipment Hookup
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Cable Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
RS-232C Control Connections . . . . . . . . . . . . . . . . . . .13
Viewing Equipment Setup . . . . . . . . . . . . . . . . . . . . .14
DVI Hookup to RJP or DVD Player . . . . . . . . . . . . . . .15
Computer PC Hookup (DVI) . . . . . . . . . . . . . . . . . . . .15
TV/Monitor - RJP Connections . . . . . . . . . . . . . . . . . .16
Audio Connection - Digital Audio Optical Connections . .17
Menus and Displays Overview
On-Screen Menus Overview . . . . . . . . . . . . . . . . . . . .18
Other Menus and On-Screen Displays . . . . . . . . . . . . . .19
User Remote Control Key Functions . . . . . . . . . . . . . . .20
Installer Remote Control Key Functions . . . . . . . . . . . .21
Step 2. Channel Search and Reception Setup
Auto Program (Do a Channel Search) . . . . . . . . . . .22
Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Channel Labels Setup . . . . . . . . . . . . . . . . . . . . . . . 24
Unstable Screen . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Checking the Strength of Digital Signal . . . . . . . . . . . 25
Step 3. Customize the TV’s Features
Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .26-30
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31-37
Caption Menu . . . . . . . . . . . . . . . . . . . . . . . . . .38-39
Sound Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 40-42
Language Control . . . . . . . . . . . . . . . . . . . . . . . . .43
Set ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Picture Menu . . . . . . . . . . . . . . . . . . . . . . . . . .45-47
Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . .48
Commercial Mode Setup . . . . . . . . . . . . . . . . . . . . . .49
Cloning Connections/Learning Setup . . . . . . . . . . . . . .50
Clone Programmer Learning Setup . . . . . . . . . . . . . . .51
Cloning Connections/Teaching Setup . . . . . . . . . . . . .52
Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . .53-58
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59-62
TV/STB Aux Input Configuration . . . . . . . . . . . . . . . .63
RS-232 Monitor Requirments/RS-232 Troubleshooting . . .64
RS-232C Control . . . . . . . . . . . . . . . . . . . . . . . . .65-66
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .67-69
Installer Quick Setup Guide. . . . . . . . . . . . . . . . . . .70
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . .71
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
The table of contents lists the pages to go to for setting up the features for the end user.
Optional Installer Remote Control for Model No. Series HCS5610
The Installer remote control is NOT included with the HD Integrator Box System.
•However, the user's remote is included with the HCS5610.
Purchase the Optional Installer's Remote and Clone Programmer
To perform a normal installation set up, you need an installer's remote and the LT2002 Quickset II Clone Programmer –
both are shown and described in later sections. See your Zenith/LG dealer if you wish to purchase the Installer remote and
LT2002. The installer remote allows access to the Installer menus, User menus in the Manual Channel Set options on the
Setup menu. The installer remote has Menu, Select, and Adjust Keys. The LT2002 Quickset II Clone Programmer is used to
duplicate a TV/STB setup and install it on another identical TV/STB.
*Note: Design and specifications are subject to change without prior notice.
PAGE 6
Installation Overview
•Unpack the HD Integrator Box System
and all accessories.
•Determine installation location for the
HD Integrator Box System, TV stand or
mount.
•Determine mounting and installation
requirements. If used, AC Power
source outlet, Antenna/Cable service
connectors, any external equipment
required for system or TV operation,
all necessary cables, wires, connectors
and any other additional required
hardware, etc.
Installation Overview & System Setup:
Questions to Consider Before
Installation
VESA Bracket
Does the VESA Bracket have to be
mounted to the TV? Y: Install VESA
Bracket on TV following the instructions
supplied with the bracket.
Yes___ No___
TV Stand
Does the TV have to be mounted on the
stand? Y: Mount the TV on the stand
following the instructions provided with
the TV stand.
Yes___ No___
Installer's Remote Control
Does the Installer have the optional
Installer's remote control available to
use to set up the TV (This is a must for
TV setup.)?
Yes___ No___
Master TV Setup
Will the Master TV's features setup be
cloned and copied to other identical HD
Integrator Box Systems?
Yes___ No___
LT2002 Quickset II Clone Programmer
To copy the TV's setup, the installer will
need a clone programmer. Is there a
Zenith LT2002 Clone Programmer
available?
Yes___ No___
End-User Remote Control
Will a remote control be provided to the
end user to operate the TV? (The remote
is included with the TV.)
Yes___ No___
End-User Menu Access
Will the end-user have access to all the
menus on the TVs from the front panel?
Yes___ No___
HD Integrator Box System Setup
Checklist
1. Install the HD Integrator Box System
where it will be used.
Prior to Operation
The HD Integrator Box System must be
connected to all external antenna/cable,
video, and audio source equipment.
See page 5, Table of Contents.
2. Make all external source equipment
connections. See pages 10 - 17.
3. Connect the HD Integrator Box
System to a standard 120V, 60 Hertz, AC
power source. See page 14.
4. Turn on the TV and all source
equipment.
Review TV Setup Options in the
Installer's Menu Section
The Installer's menu includes a number
of options for the master TV's setup that
enable the installer or system
administrator to devise a unique system
using the many different options and
variables available. See Installer's menus
section.
*Note:
If using the HCS5610 with a TV that has
Commercial Lite, Public Display Mode, select
'No'' for the Public Display Mode menu option
to disable Public Display Mode.
Master TV Features Setup for Cloning
Overview
•Set up Installer's remote control, see
page 21.
•Do a Channel Search, see page 22.
•Channel List.
•Channel Label.
•Video/picture appearance options
setup, see Picture menu.
•Audio/sound options setup, see Sound
menu.
•Set up all other features. See page 5,
Table of Contents, for a list of features
available on this HD Integrator Box
System.
Clone Master TV's Setup
See Clone Programmer section.
*Note:
After installing a PPV card in the HCS5610
be sure to disconnect the AC power cord for
5 seconds and reconnect it.
Supplied Accessories List
- 5 ft. HDMI to DVI-M Cable
- 1 ft. HDMI to DVI-F Cable
- 5 ft. RS-232 Control Cable
- 6 ft. AC Power Cord
- 3 ft. IR Receiver Cable
- Screws & Wall Mount Bracket (5-
Required)
- 1 ft. RCA Jack to Stereo Plug
Cable(3.5mm)
- 5 ft. Stereo Plug to RCA Plug to Stereo
Plug(3.5mm)
- Installation Guide
- User Remote Control & Batteries
(Included)
- Installer Remote Control & Batteries
(Optional)
Setup Checklist
Installation/Connections Overview
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
PAGE 7
M.P.I Interface
Cable In
To hook up source equipment, see below and also refer to the Table of
Contents on page 5; shows pages to go to for equipment hookup options.
Audio In
Audio Out
RS-232C Port
AC Out
Remote In
RJP Interface
Digital Video Out
AC In
Digital
Audio Out (Optical)
Display Control
Digital Video 1, 2 In
AUX Control
POWER
STATUS
RESET
UPDATE
A
B
C
D
POWER
STATUS
RESET
UPDATE
POWER LED
The POWER LED illuminates while the display panel is on.
The LED is off when the display panel is off.
STATUS LED
The STATUS LED flashes while the program is running.
RESET
Press RESET to start the program that re-initializes the HCS5610.
UPDATE
Press UPDATE to allow software to be updated. To start the download program,
press and release the RESET button while holding down the UPDATE button.
A C
DB
HCS5610 front panel controls and LED functions
Ventilation
PAGE 8
The HCS5610 Integrator Box as well as Plasma monitors generate heat during operation and need
to be provided with adequate ventilation to assure continued reliable operation. See recommenda-
tions below.
Proper clearance for air to flow around the HCS5610
Integrator Box must be provided.
Be sure proper ventilation is provided for the monitor, see monitor
installation guide for specified ventilation requirements.
Ventilation Clearance
Monitor Ventilation
There are ventilation holes on four sides of the the
HCS5610 box provided for ventilation cooling.
a. If the box is mounted vertically, the vents on the
sides should be located on the top and bottom for
free vertical air movement.
b. If the box is mounted horizontally, the vents should
be located at the sides and top of the enclosure
(never mount the box with vents facing down). See
drawings to the right for reference.
The vent holes should never be blocked or obstructed to
airflow but have an unimpeded path through any enclo-
sure back to room temperature air.
The unit and its venting, should not be installed near
heat sources such as radiators or heating ducts.
If the unit is placed in an enclosure, tests should be run
to confirm that the ambient temperature around the unit
under normal expected operating conditions is stable and
does not exceed 40 degrees Celsius (104F). This can be
determined by placing a thermometer near the air intake
vents in the proposed enclosure and measuring the
temperature every hour, under normal operating
conditions, until two successive readings repeat.
If temperature does not stabilize but keeps increasing
above 104F, ventilation is inadequate and needs to be
improved.
Always provide adequate air space between the ventila-
tion areas and adjacent structures.
*Note:
In addition to the ventilation requirements shown, be sure to
allow enough clearance (4” - 5”) for wiring clusters attached to
the Integrator Box.
1
2
3
4
5
Vent Holes Vent Holes
Vent Holes
Vent Holes
Vent Holes
Vent Holes
Ventilation / Installation Overview
PAGE 9
Angled brackets are provided so that the Integrator Box can be
mounted on a flat vertical surface, like a wall.
Install the angled brackets with the screws provided.
Mount Integrator Box on the wall using appropriate screws.
*Note:
The brackets are designed to be mounted to typical 16” spaced wall studs.
Do not mount the Integrator Box to a weak wall surface. If wall studs are not
available, use some other appropriate fastening system.
Vertical Installation (Wall Mount) Using Supplied Angled L-Brackets
The plasma and LCD monitor and Integrator Box can be mounted to a
wall using an optional Monitor/Integrator Box wall mounting system.
For further information on the mounting system, see your LG dealer.
Monitor/Integrator Box Wall Mounting System
AUX Controller: Connection and Placement
PAGE 10
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN MAX 8A 960W AC 120V~ 60Hz
12
(+)( ) (+)
( )
AUDIO
(MONO)
RLVIDEOYP
BR
P
AV INPUT
AUDIO
RL RL
EXTERNAL SPEAKER (8)AC INPUT
AUDIO INPUT
S-VIDEOCOMPONENT(480i/480p)RGB-PC INPUT
(VGA/SVGA/XGA/SXGA)
(DVD INPUT)
RS-232C
IR Bracket
IR Receiver
Install the IR Receiver and Bracket Assembly to the back of the monitor using the method described below.
The IR Receiver should be installed in the IR Bracket. When the IR Bracket assembly is attached to the TV, it
should be mounted with two-sided tape on the bottom-back side of the TV. The IR receiver should be aimed
toward the TV viewer and be visible at the bottom front of the TV, in order that it be able to receive IR sig-
nals from the user remote.
IR Receiver & Bracket Installation
THE IR RECEIVER UNIT IS PROVIDED. THIS WILL NEED TO BE MOUNTED ON THE MONITOR BACK WITH TWO-SIDED TAPE.
IR Receiver & IR Bracket Installation
Connect the AUX Controller to allow the Integrator Box to operate your AUX device.
1
2
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN MAX 8A 960W AC 120V~ 60Hz
12
Connect the AUX Controller to the AUX CONTROL cord on the TV/STB.
Place the AUX Controller under and in front of the AUX device.
The AUX Controller must extend just out in front of the infrared sensor on the AUX device.
*Note:
If the infrared sensor is not marked on your AUX device, shine a flashlight into the front panel of the AUX device to locate
the sensor.
DVD (Front View)
AUX Controller
DVD
(Side View) 1/2”
to 1”
IR Sensor
Monitor
Connections Panel
Connections Panel
Antenna Hookup
PAGE 11
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT
AUX
CONTROL
DIGITAL
VIDEO OUT
DIGITAL
VIDEO IN
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT
AUX
CONTROL
DIGITAL
VIDEO OUT
DIGITAL
VIDEO IN
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
1
2
3
RF Coaxial Wire
(75 ohm)
300/75 ohm
Adapter
Connections Panel
Connections Panel
Locate the Antenna/Cable jack on the back
of the HD Integrator Box System.
Connect the antenna wire (Flat or Round)
that runs from the wall to this jack,
according to one of the diagrams shown to
the right.
After all connections are complete, plug in
the TV. The HD Integrator Box System is
designed to operate on AC power.
Flat Wire
(300 ohm)
Connect an off-air antenna to the HD Integrator Box System.
If the antenna is a 75 ohm RF cable, then no
adapters are required.
A 300 to 75 ohm adapter is not included with
the Zenith HD Integrator Box System.
Mini glossary
75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking
through the middle, and it screws onto the threaded jack on the back of the TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws
on one end and a round opening with a wire sticking out on the other end.
300 TO 75 OHM
ADAPTER
Cable Service Hookup
PAGE 12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT
AUX
CONTROL
DIGITAL
VIDEO OUT
DIGITAL
VIDEO IN
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT
AUX
CONTROL
DIGITAL
VIDEO OUT
DIGITAL
VIDEO IN
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
Locate the Antenna/Cable jack on the
back of the TV/STB.
Connect the cable wire to the
Antenna/Cable jack according to one
of the diagrams to the right.
After all connections are complete,
plug in the TV. The HD Integrator Box
System is designed to operate on AC
power.
1
2
3Connections Panel
Cable TV
Wall Jack
RF Coaxial
Wire (75 ohm)
Cable TV
Wall Jack
Coaxial Wire
RF (75 ohm)
Connections Panel
Connect cable service to the HD Integrator Box System.
Mini glossary
75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking
through the middle, and it screws onto the threaded jack on the back of the TV.
A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two
screws on one end and a round opening with a wire sticking out on the other end.
300 TO 75 OHM
ADAPTER
RS-232C Control Connections
PAGE 13
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
Connect the Display Control (RS-232C) port from the TV/STB to the display panel to control TV
functions with RS-232C commands
ONCE THE RS-232C CONNECTION IS MADE BETWEEN THE TV/STB AND THE DISPLAY PANEL, THE DISPLAY PANEL CAN ONLY BE CON-
TROLLED BY THE TV/STB.
To
RS-232C Input
Port
Typical Plasma or LCD
Display Panel
To
Display Control
Output Port
Connections Panel
*Note: Some TV/Monitor installations will require RS-232 Null modem cable(s) with gender changers.
Viewing Equipment Setup
PAGE 14
Connect the TV/STB to the display device that will be used to view the signal.
An unswitched AC power outlet is specifically provided on the TV/STB to plug the
display panel into.
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
. . . . . . . .
. . . . . . . .
. . . . . . . .
HCS5610 PTC INSTALLER MENU
UPN 000-000-000-000 FPGA E0F1
PTC V1.00.000 CPU V1.00.00
000 INSTALLER SEQ 000
Plasma or LCD Display Panel Setup for use
with the TV/STB Commercial Interface
Control Box
Connect RS-232C cable. (See previous page.)
Connect IR Receiver cable to Remote In
port.
Connect the Cable Out jack to the display
panel, typically the Antenna (In) jack.
Plug the display panel AC power cord into
the convenience AC power outlet provided
on the TV/STB.
Plug the TV/STB AC power cord into a stan-
dard 120V 60 Hz power outlet.
Once power is applied to the TV/STB, the AC
power outlet is active. The LED on the dis-
play panel will turn red, indicating that the
panel is in standby mode.
Use the user-supplied remote control to turn
on the TV/STB.
Connect Aux Control IR Output
as required of your system.
3.5mm Stereo Plug
with IR Receive
Antenna
Wall Jack
FR Coaxial Wire
(75ohm)
DVI
AC Power
Coad
3.5mm
Stereo Plug
Audio
R - L
PAGE 15
Computer PC Hookup (DVI)
Locate the DVI out port on
the RJP (Remote Jack Pack)
or DVI device.
Connect a DVI cable
between the RJP and DVI in
port on the TV/STB.
If required, make Audio
connections as indicated to
the right.
After all connections have
been made, select the DVI
source to display the DVI
image on the TV.
1
2
3
Locate the computer DVI out port on
the computer.
Connect a computer cable between the
computer and DIGITAL VIDEO In on
the TV/STB.
Make PC Audio connections as
indicated to the up.
After all connections have been made,
select the DIGITAL VIDEO 1 or 2 source
to display the PC image on the TV.
1
2
3
AUDIO IN DIGITAL
VIDEO IN
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
AUDIO IN DIGITAL
VIDEO IN
12
DVI Hookup to RJP or DVD Player
PAGE 16
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
.....
.....
TV/Monitor
HDMI (DVI) Source
Selected
. . . . . . . .
. . . . . . . .
. . . . . . . .
. .
.
. .
.
. .
. . .
. . .
.
.
.
. .
. .
.
. .
3.5mm
Stereo Plug
3.5mm Stereo Plug
with IR Receiver
Composite
Video
RGB
from RJP
Cable Bundle
RS-232
R-Audio-L
TV/Monitor
Power Cord
R-Audio-L
Optional
Cable
with RJP
Composite
Video
(Use with
R-Audio-L
plugs from
Audio Out)
Connect to
Power Outlet
HDMI
DVI
RGB
from RJP
Cable Bundle
RF Coaxial Wire
(75 ohm)
RJP
Control
Cable
USB
Antenna
Wall Jack
Connect to TV/Monitor
TV/Monitor - RJP Connections
A
A
PAGE 17
Audio Connection – Digital Audio Optical Connections
Hook up a Digital Audio Amplifier System using the Digital Audio Optical Out port, according to the diagram
above.
Select the Digital Audio Optical input source on the Amplifier.
Digital Audio Optical Output Connections to External Amplifier
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
To Digital Audio
Optical In Port
From Digital Audio
Optical Out
Port
Typical Digital Audio
Amplifier System
Connections Panel
PAGE 18
On-Screen Menus Overview
ON-SCREEN MENUS
CHANNEL MENU Adjusts the basic operational features of the TV.
Auto Program 22 Automatically finds and stores active channels to scroll through using Channel Up/Down.
Channel List 23 Manually picks and chooses which active channels will appear when using Channel Up/Down.
Channel Label 24 Labels the channels with their network names (ABC, CBS, HBO, etc.).
Fine Tune 25 Automatically adjusts the picture for optimum appearance.
Signal Strength 25 Reveals the strength of the incoming digital signal.
SETUP MENU
Time 26 Sets the time.
V-Chip 31 Sets up restrictions or changes the password for Parental Control.
PC With computer connected, sets up PC image appearance.
Menu Language 43 Picks the language the on-screen menus will appear in.
Menu Transparency 43 Selects the degree of menu opacity.
Set ID 44 Specifies the TVs identity.
CAPTION MENU 38 Chooses analog and digital captioning options.
SOUND MENU 41 Sets up the sound.
Options are: Mode, Balance, Digital Output, Auto Volume, Multi-Track, Internal Speaker.
PICTURE MENU 45 Sets up the picture appearance.
Options are: Mode, Color Temperature, Screen Format, Noise Reduction, Film Mode.
19 OTHER MENUS AND ON-SCREEN DISPLAYS
Volume Shows current sound level.
Sleep Timer Sets a time the TV will turn off.
SAP Selects MTS sound: Mono, Stereo, and SAP in analog mode. Change the audio language in DTV mode.
Captions Selects Caption/Text options.
Alarm Set a time for the TV to turn itself on.
Guide View DTV program information. With Guide displayed, press Info for additional program information.
Channel Preview -> V-Chip Displays the available TV channels and guest’s Parental Control menu.
Info Shows program details: Title, Broadcast Time, Signal Format, Signal Strength CC, V-Chip, Language, Sound
Format, Time, Date, Channel Icon, Channel Label.
INSTALLER MENUS
Installer Menus 53 Makes adjustments to the TV’s operational features.
RS-232C Control
RS-232C Control 65 Control TV through TV/STB.
Menu Name Page Description
Descriptions of the menus and on-screen displays.
PAGE 19
Other Menus & On-Screen Displays
Use the remote keys indicated below to access these menus and displays.
In this manual, the OSD (On Screen Displays shown) may be different than those on the actual TV.
The following are generic examples to familiarize you with the TVs options.
Volume Display
Press VOLUME.
Shows currently selected sound setting.
Sleep Timer Menu
Press TIMER.
Sets a time to automatically turn the TV off
and shows remaining time before TV shutoff.
SAP Display
Selects MTS sound: Mono, Stereo, and
SAP in analog mode. Change the audio
language in DTV mode.
Caption Display
Press CC.
Turns selected option on or off. See
Closed Captions page to select options.
Alarm Timer
Current Time 11:17 AM
AdjustMove Exit
OK
Hr.
Off
Min.
Alarm Display
Press ALARM.
Set a time for the TV to turn itself on.
Channel Preview
Press CH PREVIEW.
Displays available TV channels.
V-Chip
Press CC.
Move to the V-Chip menu.
Guide Display
Press GUIDE to view DTV program
information. Press Info for more
program information.
INFO
Press INFO.
Check the current program information.
CAPTION Service1 GF
SAP English GF
19
12
6
9
3
TIMER Off
PAGE 20
User Remote Control Key Functions
A list of the keys and their functions on the user remote control supplied with the HD Integrator Box
System.
POWERMUTE
TV/AV
CH
PREVIEW
GUIDE
SAP INFO
123
456
7
-
89
0
CC
TIMER
FLASHBK
CH
CH
VOL
OK
VOL
ALARM
MUTE
Turns sound Off and On, while the picture
remains.
GUIDE
Use to view DTV program information.
Press INFO for additional information.
CC
Press to activate English subtitles.
ALARM
Use to go to the Alarm menu. Set a time
for the TV to turn itself on.
POWER
Turns TV On or Off.
TV/AV
Displays a menu of all available input
sources.
SAP
Selects MTS sound: Mono, Stereo, and SAP
in analog mode. Change the audio
language in DTV mode.
INFO
Check the current program information,
screen status, multi-sound status and time.
Press with Guide onscreen for more
Program information.
[-] BUTTON
When selecting a digital broadcast
channel, key in the Main channel
number followed by the-> [-] -> then the
sub channel number. Analog channels do
not contain a sub channel number.
VOLUME / CHANNEL / OK (Enter)
Increase or decrease the volume /
Change channels.
Select on-screen menu items and change
menu values.
NUMBER BUTTONS
Use for direct channel entry.
TIMER
Press repeatedly to select a preset time to
automatically shut the TV off.
CHANNEL PREVIEW
Displays available TV channels, and (if
active) the Guest Parental Control menu:
set V-Chip blocks to restrict both analog
and digital programming.
• Aux Channel allows the guest to select
the Audio / Video inputs. (Use the A/V
jacks on the back of the TV as a source).
FLASHBK (FLASHBACK)
Use to return to the last channel
viewed.
User
Remote Control
PAGE 21
Installer Remote Control Key Functions
A brief list of the keys on the optional installer’s remote and what they do.
MUTE
Turns sound Off and On, while the picture
remains.
CHANNEL (-/+)
Tunes to next available channel.
ENTER (OK)
Press to view the Channel/Time display or
to remove any on-screen display or menu.
ALARM
Use to go to the Alarm menu. Set a time
for the TV to turn itself on.
CHANNEL PREVIEW
Displays available TV channels, and (if
active) the Guest Parental Control menu:
set V-Chip blocks to restrict both analog
and digital programming.
• Aux Channel allows the guest to select
the Audio / Video inputs. (Use the A/V
jacks on the back of the TV as a source).
MENU/SELECT/ADJ (Adjust)
Press to display the main on-screen menu.
Use SELECT to choose an option and ADJ
(adjust) Left/Right to change the selected
option.
Optional Installer
Remote Control
POWER
Turns TV On or Off.
TV/FM
Down arrow for navigating menus.
VOLUME (-/+)
Decreases/increases sound level.
NUMBER KEYPAD
Selects channels directly and enters
numerical values for some options.
TIMER
Press repeatedly to select a preset time to
automatically shut the TV off.
[-] BUTTON
When selecting a digital broadcast
channel, key in the Main channel
number followed by the-> [-] -> then the
sub channel number. Analog channels do
not contain a sub channel number.
CC (Closed Captioning)
Press to access closed captions.
FLASHBK (Flashback)
Returns to the previous channel viewed.
PAGE 22
Auto Program (Channel Search)
With the optional Installer remote control in hand and press
the POWER button to turn the TV on.
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Channel menu and press the OK (Enter)
button.
Press the OK (Enter) button to highlight Auto program.
Press the OK (Enter) button to start the channel search.
After finding all available channels, a display appears
briefly showing the number of analog and digital channels
found.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
Use Auto Program to automatically find and store all of the channels
available in the selected Tuning Band.
*Notes: Tuning Band must be set before doing the channel search. See Installer
menu item 003 Band/AFC. Default setting is 1, for CATV. When Auto Program is
run, any assigned channel labels are automatically removed.
Auto Program finds channels being received
by the TV’s analog and digital tuners.
Cable will not work unless you subscribe to
a cable service.
Antenna
Auto Program G
Channel Label
Channel List
Fine Tune Auto
Signal Strength
--:-- --
--. -- ----
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
Press OK to Search
Yes
DE Move OK Select MENU Back
F G Move OK Select MENU Back
MENU Back
PAGE 23
Channel List
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Channel menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Channel List and
press the OK (Enter) button.
Use the ADJ Dor Ebutton to highlight the channel you wish
to delete and press the ADJ Gbutton.
The ADJ Gbutton toggles the check mark on and off.
If the check mark appears next to the channel number, the
channel appears in the channel scan.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
After the channel search, remove unwanted channels.
If you delete a found channel, it isn’t gone forever.
Simply re-enter the Channel List menu and re-add the
channel to show the check mark.
Antenna
Auto Program
Channel Label
Channel List G
Fine Tune Auto
Signal Strength
--:-- --
--. -- ----
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
DE Move OK Select MENU Back
DE Move G Add/Del OK View MENU Back
Adding Active Channels (Before 2-5-5+Menu)
Key in active channel number.
Go to the Channel List.
Click on the right arrow to add the checkmark next to the
channel number.
Press MENU to exit all menus.
When 2-5-5+Menu is run, the channel number will be added
to the channel scan.
*Note: For broadcast channel numbers, key in the Physical channel
number and add it to the channel list.
1
2
3
4
PAGE 24
Channel Control (Continued)
-Channel Labels help the user identify the channel or network being
viewed.
In the Setup menu with the Channel Labels option highlighted, use
the ADJ D E F G buttons to scroll through the available channel
labels, such as, A&E, AMC, ESPN, HBO, etc. These are a series of
preset labels from which you can choose the more common networks.
Use any of these to label the channels in the TV’s memory.
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Channel menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Channel Label and
press the OK (Enter) button.
This action displays the Channel Label menu.
Use Channel Dor E(+ / -) button to select channels and
the ADJ D E F G buttons to navigate the labels menu.
When the label is highlighted you want for the channel shown
in the screen and press OK (Enter) button to add the label to
the channel.
Select the next channel to label with Channel Dor E(+ / -)
button to or if finished channel labeling.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
Channel Labels Setup
Antenna
Auto Program
Channel Label G
Channel List
Fine Tune Auto
Signal Strength
--:-- --
--. -- ----
DE Move OK Select MENU Back
Previous Move Change Ch. Add/DeleteCH
PAGE 25
Channel Control
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Channel menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Signal Strength and
press the OK (Enter) button.
View the on-screen signal strength monitor to see the quality
of the signal being received.
When finished, press MENU repeatedly to remove the menus.
3
2
1
-This shows the current digital signal strength as a picture.
(This is only available for digital broadcasting.)
Checking the Strength of the Digital Signal
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Channel menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Fine Tune and press
the OK (Enter) button.
Press the ADJ For Gbutton to adjust.
When finished, press MENU repeatedly to remove the menus.
2
1
-If a dashed line or no color appears, the screen is unstable, therefore
try channel adjustments.
(This is only available for analog broadcasting.)
Unstable Screen
4
3
4
Antenna
Auto Program
Channel Label
Channel List
Fine Tune Auto G
Signal Strength
--:-- --
--. -- ----
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
DE Move OK Select MENU Back
F G Adjust MENU Back
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength G
--:-- --
--. -- ----
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
--:-- --
--. -- ----
DE Move OK Select MENU Back
MENU Back
PAGE 26
Clock Setup (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor E button to the Time.
Press the OK (Enter) button to highlight Clock.
Manual or Auto will appear on the menu next to clock. If
manual is selected, on the menu use the ADJ Dor Ebutton
to highlight Manual and press the OK (Enter) button.
Use the ADJ Dor Ebutton to highlight Manual Clock and
press the OK (Enter)button.
Use the ADJ DEF Gbuttons to set the year, month, day,
AM/PM, hours and minutes.
When finished, press MENU repeatedly to remove the menus.
3
4
5
6
2
1
-Use the ADJ D E F G buttons to set the year, month, day, hours and
minutes.
Manual Time Settings
--:-- --
--. -- ----
--:-- --
--. -- ----
Clock Manual G
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off Off
--:-- --
--. -- ----
Clock Manual
Manual Clock G
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off Off
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Auto
Manual
--:-- --
--. -- ----
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Time
G
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
--:-- --
--. -- ----
DE Move OK Select MENU Back
DE Move OK Select MENU Back
DE Move OK Select MENU Back
DE Select MENU Back
DE Adjust F G Move MENU Back
On-Off Timers Setup
Set the On-Off Timers using the procedures described above.
*Notes: If you intend to use the On-Off Timers, it is best to set the
clock manually.
PAGE 27
Clock Setup (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor E button to the Time.
Press the OK (Enter) button to highlight Clock. Manual or
Auto will appear on the menu next to clock. Select Auto on
the sub-menu with the ADJ Dor Ebutton and press the OK
(Enter) button.
Use the ADJ DEF Gbuttons to set the Daylight Savings
and Time Zone options for your local area.
See the next page.
When finished, press MENU repeatedly to remove the menus.
3
4
5
2
1
-If you select auto time setting, time will be set from the digital
broadcast information.
Automatic Time Settings
Caution: Some digital channels may change the time
incorrectly using the Automatic Clock Set feature.
In this event, the Alarm may not function as intended and
the TV may not turn on at the expected time.
If the end user will have access to the Alarm, it may be best
to use the Manual Clock Set mode and set the clock to local
time manually.
Time
G
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
--:-- --
--. -- ----
--:-- --
--. -- ----
--:-- --
--. -- ----
Clock Manual G
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off Off
Auto Off
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto
Manual
DE Move OK Select MENU Back
DE Move OK Select MENU Back
DE Select MENU Back
Mini glossary
TIME A four-digit figure broken down into hours and minutes, used to enter the current time when setting the clock or wake-up alarm.
HOURS First two digits that are entered when setting the clock or the wake-up alarm.
MINUTES The last two digits that are entered when setting the clock, or the wake-up alarm.
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor E button to the Time.
Press the OK (Enter) button to highlight Clock.
Use the ADJ Dor E button to highlight the Daylight Saving
and press the OK (Enter) button.
Use the ADJ Dor Ebutton to choose Yes or No.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
-Installer can select to use Daylight Savings to adjust the clock time.
This is operated from the Automatic Time Settings.
-Installer can set the Time Zone. This is operated from the Automatic
Time Settings.
1
2
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor E button to the Time.
Press the OK (Enter) button to highlight Clock.
Use the ADJ Dor Ebutton to highlight Time Zone and press
the OK (Enter) button.
Use the ADJ F or G button to select the Time Zone and
press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
3
4
5
6
PAGE 28
Clock Setup (Continued)
Setup
11:20 PM
Sep.11, 2006
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
No
Yes
Time
G
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
DE Select MENU Back
Daylight Saving
Time Zone Settings
11:20 PM
Sep.11, 2006
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Easten
Time
G
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
F G Select MENU Back
Clock Setup (Continued)
PAGE 29
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor E button to the Time.
Press the OK (Enter) button to highlight Clock.
Use the ADJ Dor Ebutton to highlight On Timer and press
the OK (Enter) button.
Use the ADJ DEF Gbuttons to choose AM / PM, Hours,
Minutes and time period to turn-on.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
1
2
3
4
5
6
-You can set a time for the TV to automatically turn-on.
TV Activation Time Settings
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor E button to the Time.
Press the OK (Enter) button to highlight Clock.
Use the ADJ Dor Ebutton to highlight Off Timer and press
the OK (Enter) button.
Use the ADJ DEF Gbuttons to choose AM / PM, Hours,
Minutes and time period to turn-off.
When finished, press MENU repeatedly to remove the menus.
-You can set a time for the TV to automatically turn-off.
TV Deactivation Time Settings
11:20 PM
Sep.11, 2006
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Time
G
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
DE Adjust F G Move MENU Back
Time
G
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
11:20 PM
Sep.11, 2006
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
DE Adjust F G Move MENU Back
PAGE 30
Clock Setup
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor E button to the Time.
Press the OK (Enter) button to highlight Clock.
Use the ADJ Dor Ebutton to highlight Auto Off and press
the OK (Enter) button.
Use the ADJ Dor Ebutton to choose On or Off.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
-If there is no signal on the TV for 15 minutes or more, or if no button
is pressed for more than 3 hours, this function turns off the TV
automatically.
Auto Off
11:20 PM
Sep.11, 2006
Clock
Manual Clock
Daylight Saving
Time Zone
On Timer
Off Timer
Auto Off
Off
On
DE Select MENU Back
Time
G
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
PAGE 31
V-Chip (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight V-Chip and press the
OK (Enter) button.
Use the ADJ Dor Ebutton to highlight On/Off and press the
OK (Enter) button.
Use the ADJ Dor Ebutton to highlight On and press the OK
(Enter) button.
If a password has been entered, key it in using the number
keypad. If no password has been set, enter the 4 digits
password (0-9) using the remote control. This is the PIN.
Each time the menu is entered, the password will be required
until the block time expires. The TV is set up with the default
password “0-0-0-0”.
Use the ADJ Dor Ebutton to highlight Changing PIN and
press the OK (Enter) button.
Enter the digits password.
As soon as the 4 digits are entered, re-enter the same
4 digits on the Confirm PIN.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
7
8
Entering a PIN (Password)
-This option sets up or changes the password for blocking program
ratings.
If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the
remote control.
Time
V-Chip
G
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
On/Off
Changing PIN
Set Block Hour
TVPG Rating
D/L Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
Off
On
On/Off
Changing PIN
Set Block Hour
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
On/Off On
Changing PIN
G
Set Block Hour 12
TVPG Rating
D/L Rating
MPAA Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE Select Menu Back
DE Move OK Select Menu Back
0 ~ 9 Number Menu Back
PAGE 32
V-Chip (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight V-Chip and press the
OK (Enter) button.
Enter the 4 digits password.
Use the ADJ Dor Ebutton to highlight Set Block Hour and
press the OK (Enter) button.
Use the ADJ Dor Ebutton to choose 1~12 hours and press
the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
Set Block Hour.
-This option sets up hour that you wish to block.
On/Off On
Changing PIN
Set Block Hour 12
G
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
On/Off
Changing PIN
Set Block Hour
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE Select Menu Back
Time
V-Chip
G
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
PAGE 33
V-Chip (Continued)
PAGE 33
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight V-Chip and press the
OK (Enter) button.
Enter the 4 digits password.
Use the ADJ Dor Ebutton to highlight the TVPG Rating and
press the OK (Enter) button.
Use the ADJ DEF G buttons to choose and set up the menu
options for TVPG Rating.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
TVPG Ratings
-You can block programs based on the TV program rating.
Description of the TV (FCC) Rating Codes:
TV (FCC) Age Categories
TV-MA
Mature audiences only. This program may contain mature themes, profane
language, graphic violence and explicit sexual content.
TV-14
Parents strongly cautioned. This program may contain sophisticated themes,
sexual content, strong language and more intense violence.
TV-PG
Parental guidance suggested. The program may contain infrequent coarse
language, limited violence, some suggestive sexual dialog and situations.
TV-G
General audience. This contains little or no violence, no strong language, and
little or no sexual dialog or situations.
TV-Y7
Directed for older children. Themes and elements in this program may
include mild physical or comedic violence, or may frighten children under the
age of seven.
TV-Y
All children. The themes and elements in this program are specifically
designed for a very young audience, including children from ages two – six.
TV (FCC) Content Sub-Categories:
VViolence.
SSexual content.
LOffensive language.
DDialog...sexual innuendo.
FV Fantasy or cartoon violence.
Time
V-Chip
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
On/Off
Changing PIN
Set Block Hour
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
On/Off On
Changing PIN
Set Block Hour 12
TVPG Rating
G
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
0 ~ 9 Number Menu Back
DE F G Move OK Select Menu Back
Time
V-Chip
G
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
PAGE 34
V-Chip (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight V-Chip and press the
OK (Enter) button.
Enter the 4 digits password.
Use the ADJ Dor Ebutton to highlight the MPAA Rating and
press the OK (Enter) button.
Use the ADJ DEFGbuttons to choose and set up the menu
options for MPAA Rating.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
MPAA Ratings
-Restricting movies by their rating.
Description of the MPAA and TV (FCC) Rating Codes:
The MPAA Rating System (Movies)
GGeneral Audience. No restrictions.
PG Children under 13 should be accompanied by an adult.
PG-13 Parental guidance suggested. Children under 13 should be
accompanied by an adult.
RRestricted. Viewers should be 17 or older.
NC-17 Not classified. Viewers should be 17 or older.
XAdults only.
• MPAA ratings: The selected rating will be locked. In addition, any ratings
that are more restrictive will also be blocked.
On/Off
Changing PIN
Set Block Hour
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
On/Off On
Changing PIN
Set Block Hour 12
TVPG Rating
D/L Rating
MPAA Rating
G
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
DE F G Move OK Select Menu Back
Time
V-Chip
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
0 ~ 9 Number Menu Back
Time
V-Chip
G
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
PAGE 35
V-Chip (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight V-Chip and press the
OK (Enter) button.
Enter the 4digits password.
Use the ADJ Dor Ebutton to highlight the Can. English
Rating and press the OK (Enter) button.
Use the ADJ DEF Gbuttons to choose and set up the menu
options for Can. English Rating.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
Canadian English Ratings
Canadian English Ratings
EExpect No restriction.
C Children
C8+ Viewers should be 8 or older.
G General Audience.
PG Parental guidance suggested. Children under 14 should be accompanied by
an adult.
14+ Restricted. Viewers should be 14 or older.
18+ Restricted. Viewers should be 18 or older.
On/Off
Changing PIN
Set Block Hour
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE F G Move OK Select Menu Back
Time
V-Chip
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
0 ~ 9 Number Menu Back
Time
V-Chip
G
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
PAGE 36
V-Chip (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight V-Chip and press the
OK (Enter) button.
Enter the 4digits password.
Use the ADJ Dor Ebutton to highlight the Can. French
Rating and press the OK (Enter) button.
Use the ADJ DEF Gbuttons to choose and set up the menu
options for Can. French Rating.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
Canadian French Ratings
Canadian French Ratings
EExpect No restriction.
GFor all
8+ Restricted. Viewers should be 8 or older.
13+ Restricted. Viewers should be 13 or older.
16+ Restricted. Viewers should be 16 or older.
18+ Restricted. Viewers should be 18 or older.
On/Off
Changing PIN
Set Block Hour
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE F G Move OK Select Menu Back
Time
V-Chip
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
0 ~ 9 Number Menu Back
Time
V-Chip
G
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
PAGE 37
V-Chip
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight V-Chip and press the
OK (Enter) button.
Enter the 4digits password.
Use the ADJ Dor Ebutton to highlight the D/L Rating and
press the OK (Enter) button.
Use the ADJ Dor Ebuttons to choose Dim0,Dim1, Dim2 or
Dim3 and press the OK (Enter) button.
Use the Dor Ebuttons to choose D1L1,D1L2 or D1L3.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
5
6
7
Downloadable Rating
On/Off On
Changing PIN
Set Block Hour 12
TVPG Rating
MPAA Rating
D/L Rating
G
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
On/Off
Changing PIN
Set Block Hour
TVPG Rating
MPAA Rating
D/L Rating
Can. English Rating
Can. French Rating
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
D/L Rating (1/1)
Dim0
Dim1
G
Dim2
Dim3
DE Move OK Select MENU Back
This function may become available in the future and
will be available only for digital channel signal.
This function operates only when TV has received
Region5 Rating data.
Your TV’s OSD (On Screen Display) may differ slightly from what is
shown in this manual.
Time
V-Chip
Menu Language
Menu Transparency
Set ID
11:20 PM
Sep.11, 2006
0 ~ 9 Number Menu Back
Time
V-Chip
G
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select Menu Back
PAGE 38
Caption Menu (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Caption menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight On/Off and press the
OK (Enter) button.
Use the ADJ Dor Ebutton to choose On or Off.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Turn Captions On/Off
Press the MENU button and then use the ADJ Dor E
button to highlight the Caption menu and press the OK
(Enter) button.
Use the ADJ Dor Ebutton to highlight Analog Mode and
press OK (Enter) button.
Use the ADJ Dor Ebutton to choose CC1-TEXT4 and press
the OK (Enter) button.
When finished, press MENU repeatedly to remove the
menus.
1
2
3
4
Analog Mode
-Analog Captions will display on the screen whether the signal is from
an RF channel or external equipment input.
*Note: Pressing CC on the remote selects a captions option.
*Note: Pressing CC on the remote to select a captions option will also turn closed
captions on.
On/Off
Off G
Analog Mode
Digital Mode
Digital Font Option
11:20 PM
Sep.11, 2006
Caption
11:20 PM
Sep.11, 2006
On/Off
Analog Mode
Digital Mode
Digital Font Option
Off
On
DE Move OK Select MENU Back
DE Select MENU Back
On/Off
On
Analog Mode CC1
G
Digital Mode
Digital Font Option
11:20 PM
Sep.11, 2006
11:20 PM
Sep.11, 2006
On/Off
Analog Mode
Digital Mode
Digital Font Option
CC1
CC2
CC3
CC4
TEXT1
TEXT2
TEXT3
TEXT4
DE Move OK Select MENU Back
DE Select MENU Back
Mini glossary
CAPTIONS The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the
hearing impaired.
TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the
broadcaster.
PAGE 39
Caption Menu
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Caption menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Digital Mode and
press the OK (Enter) button.
Use the ADJ Dor E button to choose Service 1-Service 6
and press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Digital Captions Mode
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Caption menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Digital Font Options
and press the OK (Enter) button.
Use the ADJ DEF Gbuttons to customize each option: Font
Size, Font Style, Foreground Color etc.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Digital Font Options
-Digital Captions only appear on digital channels, tune in a digital
channel that is actually broadcasting digital captions.
*Note: Pressing CC on the remote selects a captions option.
-Customize the digital captions that appear on your screen.
*Note: If the digital options custom settings are to be cloned, all menu options
should be set to any option other than Default. If Default is left set for any one
option, then all the options will be reset to default after cloning.
On/Off
On
Analog Mode
CC1
Digital Mode
Service1 G
Digital Font Option
11:20 PM
Sep.11, 2006
11:20 PM
Sep.11, 2006
On/Off
Analog Mode
Digital Mode
Digital Font Option
Service1
Service2
Service3
Service4
Service5
Service6
DE Move OK Select MENU Back
DE Select MENU Back
On/Off
On
Analog Mode
CC1
Digital Mode
Service1
Digital Font Option
G
11:20 PM
Sep.11, 2006
Font Size Default
G
Font Style Default
Foreground Color
Default
Background Color
Default
Edge Color
Default
Fore. Opacity
Default
Back. Opacity
Default
Edge Style
Default
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
DE Move OK Select MENU Back
PAGE 40
Press the MENU button and then use the ADJ Dor E
button to highlight the Sound menu and press the OK
(Enter) button.
Use the ADJ Dor Ebutton to highlight Digital Output and
press the OK (Enter) button.
Use the ADJ D / Ebuttons to choose Dolby Digital or PCM
and press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
-Set the digital audio output as Dolby Digital or PCM.
Digital Audio Output Settings
<Dolby Digital>
This product is under license of Dolby
Laboratories.
The “Dolby” or D symbol is a trademark of Dolby
Laboratories.
Sound Menu (Continued)
Digital Output
PCM G
Auto Volume
On
Multi-Track
English
11:20 PM
Sep.11, 2006
11:20 PM
Sep.11, 2006
Digital Output
Auto Volume
Multi-Track
Dolby digital
PCM
DE Move OK Select MENU Back
DE Select MENU Back
PAGE 41
Sound Menu (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Sound menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Auto Volume and
press the OK (Enter) button.
Use the ADJ Dor Ebutton to choose On or Off.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Automatic Volume Control Settings
-Have the TV automatically maintain the same sound level between
different channels.
Digital Output
PCM
Auto Volume
On G
Multi-Track
English
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
Digital Output
Auto Volume
Multi-Track
11:20 PM
Sep.11, 2006
Off
On
DESelect MENU Back
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Sound menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Multi-Track and press
the OK (Enter) button.
Use the ADJ Dor Ebutton to choose Mono, Stereo or SAP
and press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Analog Audio Settings
-You can set analog audio settings.
Digital Output
PCM
Auto Volume
On
Multi-Track
Stereo G
11:20 PM
Sep.11, 2006
Digital Output
Auto Volume
Multi-Track
11:20 PM
Sep.11, 2006
Mono
Stereo
SAP
DE Move OK Select MENU Back
DESelect MENU Back
PAGE 42
Sound Menu
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Sound menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Multi-Track and press
the OK (Enter) button.
Use the ADJ Dor Ebutton to choose English, Spanish or
French and press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Digital Audio Settings
-You can set digital audio language.
(This is only available for digital broadcasting.)
Digital Output
PCM
Auto Volume
On
Multi-Track
English G
11:20 PM
Sep.11, 2006
Digital Output
Auto Volume
Multi-Track
11:20 PM
Sep.11, 2006
English
Spanish
French
DE Move OK Select MENU Back
DESelect MENU Back
PAGE 43
Language Control
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Menu Language and
press the OK (Enter) button.
Use the ADJ Dor Ebutton to highlight and set the Menu
Language: English, Español or Français.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Menu Language
-The menus can be shown on the screen inter selected language.
First select your language.
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Menu Transparency
and press the OK (Enter) button.
Use the ADJ Dor Ebutton to highlight and set the Menu
Transparency: Opaque, Semi Opaque, Semi Trans, Transparent.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Menu Transparency Settings
-Menu Transparency sets the background transparency of the menu.
11:20 PM
Sep.11, 2006
Time
V-Chip
Menu Language
Menu Transparency
Set ID
English
Español
Français
Time
V-Chip
Menu Language English
G
Menu Transparency
Semi Opaque
Set ID 1
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
DE Select MENU Back
Time
V-Chip
Menu Language English
Menu Transparency Semi Opaque
G
Set ID 1
11:20 PM
Sep.11, 2006
11:20 PM
Sep.11, 2006
Time
V-Chip
Menu Language
Menu Transparency
Set ID
Opaque
Semi Opaque
Semi Trans
Transparent
DE Move OK Select MENU Back
DESelect MENU Back
PAGE 44
Set ID
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Setup menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Set ID and press the
OK (Enter) button.
Use the ADJ Dor Ebutton to choose 1-99 numbers and press
the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Set ID
-Use this function to specify a set ID number.
Time
V-Chip
Menu Language English
Menu Transparency
Semi Opaque
Set ID 1
G
11:20 PM
Sep.11, 2006
11:20 PM
Sep.11, 2006
Time
V-Chip
Menu Language
Menu Transparency
Set ID
D
1
E
DEAdjust MENU Back
DE Move OK Select MENU Back
PAGE 45
Picture Menu (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Picture menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Mode and press the
OK (Enter) button.
Use the ADJ Gbutton to choose a preset picture setup. When
finished, press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Picture - Preset
-Set the picture mode to the program content, e.g. Dynamic or Mild etc.
(This is only available for analog broadcasting.) Mode Standard G
Color Temperature
Normal
Screen Format
16:9
Noise Reduction Off
Film Mode
Off
11:20 PM
Sep.11, 2006
Mode
Color Temperature
Standard
G
Contrast
Brightness
Sharpness
Color
Tint
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
DEMove GSelect MENU Back
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Picture menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to choose
Color Temperature and press the OK (Enter) button.
Use the ADJ Dor Ebutton to choose Normal, Cool or Warm.
When finished, press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Color Temperature Settings
(This is only available for analog broadcasting.)
Mode Standard
Color Temperature
Normal
G
Screen Format
16:9
Noise Reduction
Off
Film Mode Off
11:20 PM
Sep.11, 2006
Mode
Color Temperature
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
Normal
Cool
Warm
DE Move OK Select MENU Back
DE Select MENU Back
PAGE 46
Picture Menu (Continued)
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Picture menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to highlight Mode and press the
OK (Enter) button.
Use the ADJ Gbutton to choose Manual and use ADJ DE
F G buttons to set your own settings for the options. When
finished, press the MENU button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Manual Picture Adjustment
To make custom picture settings, set the Mode to Manual on the menu.
Use the Manual settings for the best presentation of movies.
The patient will then be able to view movies with more realism.
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Picture menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to choose Screen Format and
press the OK (Enter) button.
Use the ADJ Dor Ebutton to choose a preset screen
format: Set By Program or 4:3. When finished, press the OK
(Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Screen Format Adjustments
The user can choose preset formats for the picture on analog channels
on analog channels.
Mode Standard G
Color Temperature
Normal
Screen Format
16:9
Noise Reduction
Off
Film Mode Off
11:20 PM
Sep.11, 2006
Mode
Color Temperature
Manual
G
Contrast
Brightness
Sharpness
Color
Tint
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
DEMove GSelect MENU Back
Mode Standard
Color Temperature
Normal
Screen Format
16:9
G
Noise Reduction
Off
Film Mode Off
11:20 PM
Sep.11, 2006
Mode
Color Temperature
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
DE Move OK Select MENU Back
DE Select MENU Back
Set By Program
16:9
Zoom1
Zoom2
4:3
PAGE 47
Picture Menu
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Picture menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to choose Noise Reduction and
press the OK (Enter) button.
Use the ADJ Dor Ebutton to choose On or Off.
When finished, press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Noise Reduction
-The user can watch movies with a more realistic picture on analog
channels.
Press the MENU button and then use the ADJ Dor Ebutton
to highlight the Picture menu and press the OK (Enter)
button.
Use the ADJ Dor Ebutton to choose Film Mode and press
the OK (Enter) button.
Use the ADJ Dor Ebutton to choose On or Off.
When finished, press the OK (Enter) button.
When finished, press MENU repeatedly to remove the menus.
1
2
3
4
Film Mode Options
The user can watch movies with a more realistic picture on analog
channels.
-Turn Film Mode On to view movies with optimum preset picture settings.
Mode Standard
Color Temperature
Normal
Screen Format
16:9
Noise Reduction
Off G
Film Mode Off
11:20 PM
Sep.11, 2006
Mode
Color Temperature
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
Off
On
DE Select MENU Back
DE Move OK Select MENU Back
Mode Standard
Color Temperature
Normal
Screen Format
16:9
Noise Reduction
Off
Film Mode Off G
11:20 PM
Sep.11, 2006
Mode
Color Temperature
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
Off
On
DE Select MENU Back
DE Move OK Select MENU Back
PAGE 48
Installer Overview
Following is the Commercial Mode Operation Setup.
Operating Installer Menu
To set up the controls for the TV you will need to know how to enter
the TV/STB Installer menu and make changes to the default values
as required. If necessary, familiarize yourself with the TV/STB
Installer menu and how to make and save changes in the menu.
Optional Installer Remote
You will need an Installer remote control similar to the one
shown to the right.
The TV’s clonable features need to be set up before 2-5-5 + Menu is done.
This is a critical step.
If the Master TV display panel’s clonable features like: Clock Set, adding channel
icons and channel labels, etc. are not done properly, then the cloned TV/STB will all
have problems. For example, do not do 2-5-5 + Menu more than once or the TV
setup will become corrupted. If you need to start the procedure over, then begin by
setting installer item 117 to 001, and pressing Enter to reset the TV to default val-
ues in the installer menu. You can do 2-5-4 + Menu mode more than once but this
mode is limited to only editing channel icons and channel labels.
Refer to the appropriate section in the Manual for other TV features: Picture, Sound
etc.
*Note: Digital Font options are available only after a channel search has been run and when
the TV is tuned to an active digital channel with digital captions.
LT2002 Clone Programmer
As the cloning procedure is being performed, specific steps need to
be done at the indicated times to achieve the desired
result. Be sure to do each cloning task as indicated. If a
procedure or step is left out or not
performed correctly, then the TV
setup will be wrong and cloning may not
work. At each step, pay attention to assure
the TV screen shows the proper message(s)
when cloning. If the message indicated does
not appear, there is a problem with that step
and cloning may not be successful. Cloning is
only possible when the signal source is an
Analog channel, not a digital channel.
HCS5610XX PTC INSTALLER MENU
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
Typical Installer Menu
QuickSet II Programmer
LT2002
¤
PAGE 49
Commercial Mode Setup
This page provides an overview of the TV configuration. See the pages listed below for more
specific, detailed instructions at each step; how to access and use the Installer menu etc.
*Note1: Disconnect all Aux inputs. Under certain conditions, Auto Program
(Channel search) is disabled if there is an Aux input active.
*Note2: Under certain conditions, changes to the input mode of the RGB
inputs will not take effect until the power is cycled (TV is turned Off and On).
To avoid confusion, disconnect all RGB inputs before entering the Installer
menu.
Overview: Commercial Mode Setup Procedure
1.Set Installer Menu Items
(Enter Installer Menu, see page 53 for detailed instructions.)
a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER.
(This clears all installer menu items, custom settings, channel labels/icons
and reloads the factory default settings.)
b. Set Item 003 BAND/AFC.
- Broadcast: set to 000.- HRC: set to 002
- CATV: set to 001. - IRC: set to 003
c. Set item 028 CH OVERIDE to 001. This allows access to Auto Program,
Channel Labels and Channel List options in the Channel Menu.
d. Set other particular installer items that affect your TV programming
network. See pages 53 - 58.
e. After all required installer menu item settings have been adjusted, press
ENTER on the remote to remove Installer Menu.
2.Set Up TV Features
(See Picture, Sound, Setup menus etc. See TV Clonable options list on
page 59.)
*Note: Digital Font options are only available after a channel search has
been run and when the TV is tuned to an active digital channel with digital
captions.
3.Run Auto Program
(Search for all available channels.) Go to the Channel menu and access
the Auto Program option, follow on-screen instructions.
a. Edit Channel Scan. In the Channel Menu, access the Channel List menu.
•Delete channels per your system requirements: do you want to delete any
free channels so the guest cannot access them?
•Add familiar Channel Icons like ABC, CBS, NBC etc. to the channel
onscreen display. Add identifiable labels for the end user to readily know
what common networks are available. In the Channel menu, select the
Channel Label option, follow instructions on the bottom of the screen.
Verify TV Setup
At this point, verify that the channel lineup, channel icons and custom
labels are correct. Make sure the TV features are set per your requirements.
4. Transfer TV Setup to Controller Box: 2-5-5 + Menu
After the TV channel scan has been edited and channel label icons added,
enter the Installer menu. Once in the Installer menu, press 2-5-5 and MENU
on the remote. This transfers the TV setup to the internal controller box.
*Note: Only do 2-5-5 + MENU once or TV setup may be corrupted.
TV scans available channels and exits menu when transfer to controller is com-
plete.
5. Perform Adding Custom Channel Labels: 2-5-4 + Menu Mode
Enter Installer menu, press 2-5-4 and Menu. Add your own custom labels to
the channel on-screen displays. (See page 60.) To remove menu press MENU.
*Note: 2-5-4 + MENU can be performed more than once.
Lock Channel Scan
Set item 028 CH OVERIDE to 000 to lock the channel scan. After the
preceding has been completed, the Master TV setup is ready to be copied to
the LT2002 Clone Programmer, see next page.
TV/STB Installer Menu
TV/STB Installer Menu Items
RJP (Remote Jack Pack) TV/STB Setup
• RJP Available? If you will use an RJP in
your system set Installer item 093 to 001.
Custom Channel Label ‘WXYZ’ created in
2-5-4 + Menu Add Channel Label Mode
After TV setup has been verified,
set item 028 Ch Overide back to 000.
HCS5610XX PTC INSTALLER MENU
117FACT DEFAULT 00X
003 BAND/AFC 00X
028 CH.OVERIDE 001
073 CH. NOT AVBLE 001
093 RJP AVAILABLE 001
028 CH. OVERIDE 000
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
WXYZ
DIGITAL 19-3
MONO SAPSTEREO
WXYZ
ANALOG 2
MONO
PAGE 50
Cloning Connections/Learning Setup
Connections for the LT2002 Clone Programmer to Learn the TV/STB Master TV Setup.
*Notes: It is assumed that the TV/STB is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an
Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone
Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, the clone programmer LED is blinking
the required heart beat pattern, see above and next page.
*Notes: Once the clone is connected, do not touch the unit or otherwise disturb it or the MPI connections. Any disturbance while the
clone is operating may disrupt the master setup transfer or copying etc.
Before you begin cloning...
•The Master TV/STB should be connected to a good, stable sig-
nal from an over-the-air antenna or cable service Analog chan-
nel and connected to power. (See above.)
•Teaching and Learning is only possible between identical model
devices. (However, the LT2002 Clone programmer can store up
to 3 different ‘master’ setups.)
WARNING: Copying a blank or incorrect memory into a TV, STB or
other device will cause the TV, STB or other device to operate
erratically or become inoperable.
•Use an Installer’s remote to operate Learning and Teaching
menus.
•Make sure that the batteries in the Clone programmer are fresh.
•If batteries are removed, the Clone Clock time will be lost.
•Decide if you want to set the time from the Clone programmer
TV which has the clock set to the current time.
•Setting the time and transferring it to the Clone or other
device is a separate procedure.
•Follow the connection diagram above to connect the Clone to
a Master TV/STB display panel. After learning is
complete, to another identical TV/STB display panel to “teach”
it the master setup.
•After the TV/STB setup has been copied to another
identical TV/STB, that identical unit with the copied setup,
needs to be disconnected from power for about 15 seconds to
activate the newly-copied setup.
•See the Clone Troubleshooting section to resolve problems.
Turn to the next page to continue Cloning Setup.
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT SERVICE
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN 120V~60Hz
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT 8A
DIGITAL
VIDEO IN
12
QuickSet II Programmer
LT2002
¤
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK= XX:XX
TV CLOCK= XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
. . . . . . . .
. . . . . . . .
. . . . . . . .
Ferrite Core
(TDK, ZCAT
2035-0930)
3.5mm Stereo Plug
with IR Receiver
DVI
RF Coaxial Wire
(75ohm)
Antenna
Wall Jack
AC Power
Cord
Clone Programmer Learning Setup
Learning the Master TV Setup
Instructions for the Clone Programmer to Learn the Master TV/STB Setup.
Use MPI Cable to Connect LT2002 Clone Programmer to
Master TV/STB MPI Port
If there is a good connection, “THE CLONE HAS CONTROL OF TV” message
will appear. Press any key on the Installer remote.
Learn Setup from Master TV/STB
Press 1 to select the “LEARN FROM TV” option, then press ON/OFF,
POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the
Memory ”Bank” you want to store the master TV/STB’s setup in by
pressing either Channel key repeatedly to choose Memory 1, 2 or 3.
(If you choose a Memory “Bank” that has a master device’s setup
programmed into it, that setup will be overwritten by the new master
TV/STB’s setup.) Once the Clone memory bank is selected, press
ON/OFF, POWER, or ENTER. The Clone memory bank you have selected
will be shown. Press ON/OFF or POWER to begin copying the master
TV/STB’s setup.
Set the Clock (Optional)
Set the time on a Master TV’s Clock. (If the time has already been
copied from a TV into the Clone programmer, you can set a master
TV’s clock by copying the time from the Clone programmer.) The
Clone Programmer can copy the current time to both a master TV and
to the Clone’s internal clock; accurate to within one minute. (Another
reason that the Clone programmer should be equipped with fresh,
high-quality alkaline batteries, is for it to keep the time as accurately
as possible.)
Since the Clone Programmer’s time cannot be set directly, the current
time needs to be copied from a Zenith/LG TV equipped with M.P.I.
input capability.
After the time is copied to the Clone programmer, the current time
can then be transferred to another TV. (This can be a master TV, or
another TV which has already had the features set up.)
*Notes: When using the clone programmer for teaching or learning,
be sure that the heartbeat pattern is shown on the LEDs. Both learning and
teaching should take about 45 or more seconds depending on the complexity
of the master setup. While the clone is functioning, do not move it or otherwise
disturb the clone or wiring connections. If the clone finishes the function in less than
45 seconds, redo the function again. Press the reset button if the clone does not act
normally.
LT2002 Clone Programmer Communication Problems
• A slow flashing green light indicates there are communication
problems between the TV/STB and the LT2002 clone
programmer. If this is the case, check for a damaged cable,
poor contacts, or other connection troubles.
• If the status indicator is red, the programmer batteries are
low and should be replaced. Install 4 high-quality alkaline AA
batteries.
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK= XX:XX
TV CLOCK= XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
This menu should appear by itself after the
LT2002 is connected to the TV/STB MPI port.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER
PAGE 51
PAGE 52
Cloning Connections / Teaching Setup
Teaching the Master Setup to Another TV/STB
Connections for the LT2002 to Teach another TV/STB the Master Setup
Teach Master TV/STB’s Setup to the target
TV/STB
After learning is complete, remove the M.P.I. cable from the
master TV/STB and connect it to the target TV/STB that you
want to copy the master TV/STB’s setup into. With “THE CLONE
HAS CONTROL OF TV” message displayed, press 2 to go to the
“TEACH TO TV” option, press ON/OFF, POWER, or ENTER.
Select the LT2002 memory that the new setup is in. Press
On/Off to transfer the new setup and other information to the
new TV/STB. Teaching usually takes 2-3 minutes.
After the “TEACHING COMPLETE” message is displayed, press any
key to return to the Clone menu, then press ON/OFF, POWER, or
ENTER. If finished, detach M.P.I. cable from the target, newly
cloned TV/STB.
Disconnect TV/STB Power for 15 Seconds
Unplug the AC power cord of the newly cloned TV/STB from the
power outlet for about 15 seconds to activate the newly-copied
setup.
CLONE SELECTION MENU
(1) LEARN FROM TV
(2) TEACH TO TV
(3) SET CLONE CLOCK FROM TV
(4) SET TV CLOCK FROM CLONE
(5) DISPLAY TV SETUP
(6) DISPLAY CLONE SETUP
-TO CHANGE MENU ITEMS, PRESS
CHANNEL KEYS OR DIGITS.
-TO EXECUTE ITEM, PRESS ON/OFF,
POWER, OR ENTER
TEACHING IN PROGRESS,
PLEASE WAIT
TEACHING COMPLETE
This menu should appear after any key is
pressed on the Installer remote.
This display will appear during Teaching
function.
This display will appear after Teaching is
complete.
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT SERVICE
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN 120V~60Hz
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT 8A
DIGITAL
VIDEO IN
12
QuickSet II Programmer
LT2002
¤
THE CLONE HAS CONTROL OF THE TV
THE CLONE IS VERSION XX
THE TV IS VERSION XX
THE SW IS REVISION XX
CLONE CLOCK= XX:XX
TV CLOCK= XX:XX
-PRESS ANY KEY TO CONTINUE.
-DISCONNECT CLONE WHEN DONE.
. . . . . . . .
. . . . . . . .
. . . . . . . .
Ferrite Core
(TDK, ZCAT
2035-0930)
3.5mm Stereo Plug
with IR Receiver
DVI
RF Coaxial Wire
(75ohm)
Antenna
Wall Jack
AC Power
Cord
Installer Menu (Continued)
Typical Installer Menu
HCS5610XX PTC INSTALLER MENU
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
Use the Installer’s Menu to set up or change operational settings.
See more detailed descriptions of the Installer menu items on the following pages...
Accessing the Installer’s Menu
Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote
control. Just press MENU repeatedly (at least 10 times) until the TV seems to stop
responding, then press 9, 8, 7, 6, then ENTER to access the Installer’s menu. To remove
the Installer’s menu, press ENTER again. Any changes you make will be stored in non-
volatile memory. (The menu also disappears automatically.)
The Installer’s menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow
keys to sequence through the available menu items. Or, access an item directly by keying
in the line number, then pressing MENU. For example, to access the Sleep Timer option
which is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Right
arrow keys. Or, enter a value directly.
Using the Installer’s Menu
Items 000 ~ 117 are immediately accessible only upon entering the Installer’s Menu.
Their numbers, descriptions, ranges, factory default settings, and a place for listing any
changes made on-site are given below and on the following pages.
Installer Menu Items 000 through 117
Menu Item Function Value Range Default Value Brief Description of Function and Comments
000 INSTALLER SEQ 0 ~ 3 0 Leave default set to 0.
001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before auto shut Off.
002 AC ON 0 / 1 0 Set to 1 to enable auto turn On at power up.
003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC
004 STRT CHANNEL 0~125, 126, 127, 255 255 Channel at turn-on (Set 255 to return to last channel before power Off).
005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.
007 STRT VOLUME 0 ~ 63, 255 255 Sets Volume level at TV turn-on (Set 255 to retain last volume level).
008 MIN VOLUME 0 ~ 63 0 Sets minimum allowable volume setting.
009 MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting.
010 MUTE DISABLE 0 / 1 0 Set to 1 to disable mute function.
015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.
016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.
017 ALARM 0 / 1 1 Set to 1 to enable Alarm.
021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip functions.
022 MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip (Parental Control) blocking hours.
023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting at power Off.
028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.
029 OLD OCV 0 / 1 0 Set to 1 to change M.P.I. operation to OCV.
030 ACK MASK 0 / 1 0 If set to 1, changes M.P.I. for some OCV boxes.
031 POLL RATE 20 ~ 169 94 Selects poll rate for M.P.I.
032 TIMING PULSE 186 ~ 227 207 Sets baud rate for M.P.I.
034 CAMPORT EN 0 / 1 1 Set to 1 to enable Video 2 input.
*Notes:
For operation with RJP series, set item 040
AUTO CAMPORT to 000. Set item 093 RJP AVAILABLE to
001. Installer menu items 004, 040, 093, affect RJP
series operation.
PAGE 53
PAGE 54
Installer Menu (Continued)
Menu Item Function Value Range Default Value Brief Description of Function and Comments
035 COMPPORT EN. 0 / 1 1 Set to 1 to enable HDMI. Set to 0 to disable.
036 FRONT Y/C EN. 0 / 1 1 Set to 1 to enable panel HDMI 2 input.
038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component 1 input jacks.
039 REAR AUX EN 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.
046 STRT AUX SRCE 1 ~ 8, 255 255 Sets the starting AUX source.
047 AUX STATUS 0 / 1 0 Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0.
053 DIS. CH-TIME 0 / 1 0 Set to 1 to disable Channel-Time display.
069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Text display.
070 FOR. CH-TIME 0 ~ 7 2 Chooses custom foreground color for the Text display.
071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Text display.
073 CH NOT AVBLE 0 / 1 0 If set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed
when directly accessing a channel not in the favorite channel list.
075 REVERT CH 0 / 1 0 If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.
078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.
079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.
080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.
081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.
082 CHKSM ERROR 0 / 1 1 Enforces rigid M.P.I. checksum.
083 HANDSHK TIME 0 ~ 5 5 Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems.
084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.
087 REAR RGB EN. 0 ~ 2 1 Set to 1 for DTV. Set to 2 for PC. Set to 0 to disable.
088 EN NOISE MUTE 0 / 1 1 If set to 1, mutes audio if no signal is present.
091 YPrPb2 EN. 0 / 1 1 Set to 1 to enable Component 2 input jacks.
092 RGB2 ENABLE 0 ~ 2 2 Set to 1 for DTV. Set to 2 for PC. Set to 0 to disable.
093 RJP AVAILABLE 0 / 1 0 Set to 1 to enable.
094 SAP MENU EN 0 / 1 1 Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu.
096 DEF. ASP. RATIO 0, 1, 2, 4, 5 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.
102 ATSC BAND 0 ~ 4 4 Selects ATSC band.
103 ATSC TUNE MODE 0 / 1 1 Sets ATSC tuning mode. Set to 0 for virtual channels, set to 1 for physical channels.
104 START MINOR CH 0 ~ 255 0 Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number.
105 VID OUT FORMAT 0 ~ 2 1 0=1080i, 1=720p, 2=480p
106 ASP RATIO LOCK 0 / 1 0 To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.
107 BANNER SELECT N/A N/A Not applicable.
108 PANEL COM 0 ~ 3 2 0=1200, 1=2400, 2=9600, 3=115200
110 PANEL DELAY 0 ~ 15 8 Sets panel delay time.
111 PANEL VOL PRE 0 ~ 100 20 Panel preset volume to achieve the same volume levels as other systems.
112 PANEL STRT VOL 0 ~ 100 20 Panel start volume when on Aux. input.
113 PANEL TYPE 0 ~ 4 2 Selects panel type.
114 PANEL MIN VOL 0 ~ 100 0 Sets panel minimum volume level.
115 PANEL MAX VOL 0 ~ 100 100 Sets panel maximum volume level.
116 VIDEO MUTE EN 0 / 1 0 Set to 0 for normal, set to 1 for Blank.
117 FACT DEFAULT 0 / 1 0 0=Normal. 1=Loads factory default presets of all above settings.
Installer Menu Items 035 through 117
Installer Menu (Continued)
Detailed Descriptions of Installer Menu Items
000 - INSTALLER SEQUENCE
Specifies entry sequence to the Installer Menu.
0 = 9876 1 = 4321
2 = 1478 3 = 3698
001 - POWER MANAGE (Power Management)
Determines hours of no activity before automatic shutoff. The
POWER MANAGE function is for saving energy. If set to 0, Power
Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing
the hours that the TV will remain On, unless there has been activity
from either the control panel or remote control.
002 - AC ON (AC Power Switchable)
If set to 1, allows the TV/STB to turn On just by applying AC power.
Pressing the On button is not necessary. This is desirable if the
TV/STB is plugged into a cable box or a power outlet
controlled by a wall switch. Use ADJ Left/Right arrow to choose 0 or
1 where 0 is the default is Off, and 1 is On.
*Note: If set to 1 (On), the TV/STB does not respond to On/Off com-
mands from either the remote or the display control panel, and the
SLEEP TIMER is also nonfunctional.
003 - BAND/AFC (Band/Automatic Frequency Control)
Selects the tuning band. There are 4 possible settings for this
option:
0 = Broadcast 1 = CATV
2 = HRC 3 = IRC
If some channels were not found by Auto Program, select the
appropriate Band setting here and add the channels using the
Channel List option in the Channel Menu.
004 - STRT CHANNEL (Start Channel)
If active, this function allows you to determine the initial channel
number when the TV/STB is turned On. This feature is useful for an
in-house information channel, since the TV/STB would always select
that channel when it is turned On. Setting this to 255 causes the
last channel viewed when the TV/STB was turned Off, to be the
tuned to channel when the TV/STB is turned On again.
255 = Last channel 1 ~ 125 = Ch X 0 = Aux
126 Map to Channel 3. 127 Map to Channel 4.
*Note: Item 004 STRT CHANNEL cannot be set to 0 if item 093 RJP
AVAILABLE is set to “1”.
005 - CHAN LOCK (Channel Lock)
CHAN LOCK is ideal if the system must always be on the same
channel. Changing channels with Channel Up/Down or keypad
numbers is impossible. Channel Lock is inactive if set to 0 (default).
Generally, this feature is used in connection with START CHANNEL
(Installer item 004) where the start channel may, for example, be
set to 3 or 4. If the start channel is 3, then the TV/STB will remain
locked on Channel 3.
007 - STRT VOLUME (Start Volume)
This function allows the Installer to determine the initial volume
level setting when the TV/STB is turned On. This feature is useful
for an in-house information channel, since the TV/STB would always
select that volume level when it is turned On. The range of values
are 0 - 63, 255. If 255 is selected, the current volume level will be
retained in memory when the TV/STB is turned Off; at turn On, the
volume level will be automatically set at the previous or last level.
008 - MIN VOLUME (Minimum Volume)
This function determines the minimum volume level allowable with
the VOLUME (VOL) Up/Down control. In this way, for example,
someone cannot set the volume too low to hear. The value range is
from 0 to 63 — change values with ADJ Left/Right arrow. The
factory default is 0, which provides the full range of volume control,
if item 009 MAX VOLUME is also set to 63. It may be best to set the
same value on every TV/STB.
*Note: The minimum volume level cannot have a value setting higher
than the MAX VOLUME level (described below).
009 - MAX VOLUME (Maximum Volume)
This function determines the maximum volume level allowable with
the VOLUME (VOL) Up/Down controls. In this way, for example,
someone can not set the volume level high enough to disturb
others.
(Continued on next page)
*Note: For Items 007, 008 and 009
For legacy reasons, the scale used is 0 - 63. The PTC software will
translate this to the 0 - 100 scale used by the TV.
To translate a TV volume level to the installer menu value, use the
following formula:
Installer Value = TV Value x 63
100
Enter only the whole number (disregard fractions).
PAGE 55
PAGE 56
Installer Menu (Continued)
The value range is 0 to 63, with 63 as the default, which gives the
user the full range of volume control, if item 008 MIN VOLUME is
also set at 0. Change values with ADJ Left/Right arrow keys. It may
be best to set the same value on every TV/STB.
*Note: The maximum volume level cannot have a value setting lower
than the MIN VOLUME level (described previously).
010 - MUTE DISABLE
Enables or disables sound mute function. If set to 1, sound cannot
be muted, mute is disabled. If set to 0, sound can be muted.
015 - SLEEP TIMER
If set to 1, the SLEEP TIMER feature may be used. If set to 0, the
Sleep Timer is not available.
016 - EN TIMER (Enable On/Off Timers)
If set to 1, Timer function is available to user. Set to 0 to disable
On/Off Timer functions. (Clock must be set in order to use Timers.)
017 - ALARM
Gives the installer the option of making the Alarm function available
to the end user. If set to 1, Alarm function is available to end user.
Set to 0 to disable the Alarm function.
*Note: Clock must be set before the Alarm function will work.
021 - V-CHIP (Parental Control)
Set to 1 to activate V-Chip (Parental Control); have it available to
end user to filter and control or otherwise restrict programming
content that can appear. Set to 0 to turn V-Chip feature Off, not
available to user; no programming restrictions can be set.
022 - MAX BLK HRS (Maximum Block Hours)
Sets hours from 0 to 99 for the maximum V-Chip (Parental Control)
block hours. Default setting is for 12 blocking hours.
023 - CAPTION LOCK
Set to 1 to restore previous caption On/Off state after turn Off. If set
to 0, captions are always Off at turn On.
028 - CH. OVERIDE (Channel Override)
If set to 1, the user can select channels with either Channel
up/down or by direct keypad entry. If set to 0, only those channels
that are added on the channel list can be selected.
029 - OLD OCV (On Command VideoTM)
Set to 1 for operation with systems from On Command Corporation.
030 - ACK MASK
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider. When set to 1, changes M.P.I. for
some OCV boxes.
031 - POLL RATE
M.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave at
default setting unless changed by Pay-Per-View provider. Step size of
16 ms.
032 - TIMING PULSE
M.P.I. Communication Parameter. Leave at default setting unless
changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3
uS.
034 - CAMPORT EN. (Camera Port Enable)
Set to 1 to enable Video 2 input on display panel. If set to 0, Video
2 input on display panel is not functional.
035 - COMPPORT EN. (Computer Port Enable)
Enable/disables display panel HDMI input jack. Set to 0 to disable,
set to 1 to enable.
*Note: The setting above is ignored if Installer item 093 RJP
AVAIL ABLE, is set to 1.
036 - FRONT Y/C EN. (HDMI 2 Enable)
Set to 1 to enable display panel HDMI 2 input.
Set to 0 to disable display panel HDMI 2 input.
*Note: The setting above is ignored if Installer item 093 RJP
AVAILABLE, is set to 1.
038 - YPrPb EN. (Rear Component Video Enable)
Set to 1 to enable display panel rear Component Video 1 input.
Set to 0 to disable display panel rear Component Video 1 input.
039 - REAR AUX EN. (Rear Aux Enable)
Set to 1 to enable display panel rear AUX (Video 1) input.
Set to 0 to disable display panel rear AUX (Video 1) input.
046 - STRT AUX SRCE (Start Aux Source)
Sets the starting AUX source.
Start source if start channel =0
1 = Video 1 5 = Component 2
2 = Video 2 6 = Component 1
3 = HDMI 1 7 = RGB 2
4 = RGB 1 8 = HDMI 2
(Continued on next page)
(Continued from previous page)
Installer Menu (Continued)
047 - AUX STATUS
Set to 1 for M.P.I. AUX source to be reported as a channel number
instead of channel 0. Set to 0 to disable AUX identification change.
Controls M.P.I. status channel response for AUX inputs.
053 - DIS. CH-TIME (Disable Channel-Time)
Set to 1 to disable the Channel-Time display, Channel-Time display
will not appear.
Set to 0 to enable the Channel-Time display.
069 - EN. CH-T COL. (Enable Text OSD Color)
Set to 1 to enable custom color for the Channel-Time display.
Set to 0 to disable custom color for the Channel-Time display.
070 - FOR. CH-TIME (Display Text Foreground Color)
Set according to Color Chart.
0 = Black 3 = Cyan 6 = Yellow
1 = Blue 4 = Red 7 = White
2 = Green 5 = Violet
*Note: If foreground and background color are the same, menu
background is transparent.
071 - BCK. CH-TIME (Display Text Background Color)
Set according to Color Chart.
0 = Black 3 = Cyan 6 = Yellow
1 = Blue 4 = Red 7 = White
2 = Green 5 = Violet
*Note: If foreground and background color are the same, menu
background is transparent.
073 - CH NOT AVBLE (Channel Not Available)
If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, “NOT
AVAILABLE” message is displayed when directly accessing a channel
not in the channel scan list available in memory.
075 - REVERT CH (Revert to Start Channel)
If set to 1 and loss of M.P.I. communication occurs, TV automatically
tunes to the specified Start Channel.
078 - UPN MSB (UPN Most Significant Byte)
User programmable number, most significant byte readable by M.P.I.
command. Note: Not linked to serial number.
079 - UPN MSB-1 (UPN Most Significant Byte-1)
User programmable number, most significant byte-1 readable by
M.P.I. command. Not linked to serial number.
080 - UPN MSB-2 (UPN Most Significant Byte-2)
User programmable number, most significant byte-2 readable by
M.P.I. command. Not linked to serial number.
081 - UPN LSB (UPN Least Significant Byte)
User programmable number, least significant byte readable by M.P.I.
command. Not linked to serial number.
082 - CHKSM ERROR (Checksum Error)
Enforces rigid M.P.I. checksum validation.
Set to 1 for validation.
Set to 0 to disable (does not check checksum on M.P.I. async port).
SPI is always checked.
083 - HANDSHK TIME (Handshake Time)
Adds an additional delay to the handshake time which is 64 msec,
thus relaxing M.P.I. timing requirements to be compatible with PC
based Windows controlled systems, range is 0 - 5.
(Timeout = 25.5MS + [25.5 MS* Handshake time]).
084 - PERMANENT BLK (Permanent Block)
Allows Lock (Parental Control) blocking schemes to be permanent by
disabling the blocking hours function.
Set to 1 to install Parental Control restrictions permanently.
Set to 0 for user-specified hours control of blocking schemes.
087 - REAR RGB EN. (Rear RGB1 Enable)
Controls access to rear RGB1 input on display panel.
Set to 1 to enable RGB1 input for DTV. Set to 2 for PC.
Set to 0 to disable RGB1 input.
088 - EN NOISE MUTE (Enable Noise Mute)
If set to 1, audio mutes if no signal is present.
091 - YPrPb2 EN. (Rear Component Video 2 Enable)
Set to 1 to enable display panel Component 2 input.
Set to 0 to disable display panel Component 2 input.
092 - RGB2 ENABLE (Red-Green-Blue 2 Enable)
Controls access to rear RGB2 input on display panel.
Set to 1 to enable RGB2 input for DTV. Set to 2 for PC.
Set to 0 to disable RGB2 input.
093 - RJP AVAILABLE
Set to 1, remote jack pack is available.
Set to 0, remote jack pack is not available.
*Note: This item can not be set to 1 if item 040 AUTO CAMPORT is set
to 1.
(Continued on next page)
(Continued from previous page)
PAGE 57
PAGE 58
Installer Menu
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable SAP feature, if available.
Set to 0 to disable SAP feature.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up, see settings below.
102 - ATSC BAND
Sets up TV to receive different types of incoming signals:
0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.
103 - ATSC TUNE MODE
Selects ATSC tuning mode: 0=Virtual, 1=Physical.
Note: The setting above is ignored if Installer item 102 ATSC BAND,
is set to 1=CATV, 2=HRC, or 3=IRC. Then 103 - ATSC TUNE MODE
above always resets itself to Physical (1), regardless of what value
appears for item 103 on the Installer menu.
104 - START MINOR CHANNEL
Sets XX-XX minor starting channel at power up: 0=NTSC. If not 0,
number
selected is the Minor start channel number.
105 - VID OUT FORMAT
0=1080i 1=720p 2=480p
106 - ASP RATIO LOCK (Aspect Ratio Lock)
Set to 1 to retain previous aspect ratio with power Off.
Set to 0 to retain default aspect ratio with power Off. See item 96
Default Aspect Ratio above.
107 - BANNER SELECT
Not applicable.
108 - PANEL COM (Newer display panels set at 2)
Sets the panel baud rate.
110 - PANEL DELAY (Newer display panels set at 8)
Sets the panel delay time.
111 - PANEL VOL PRE
Preset panel volume to achieve the same volume levels as other
systems.
112 - PANEL STRT VOL
Panel start volume when on Aux. input.
113 - PANEL TYPE (Newer display panels set at 2)
Select the Panel Type according to the table which is part of a quick
setup guide that keeps on changing as new displays become
available.
114 - PANEL MIN VOL
115 - PANEL MAX VOL
Both items above sets the min/max volume of the display panel
when using other panel aux inputs aside from the one that the STB
uses. It is similar to the Min/Max Volume for the STB (items 8 & 9).
Item 8 & 9 limits the volume coming out of the STB while items
114 & 115 limits the Panel Volume.
116 - VIDEO MUTE EN (Video Mute Enable)
Set to 0 for normal.
Set to 1 for blank.
117 - FACT DEFAULT (Factory Default)
Set to 0 for normal.
Set to 1 to load default settings for all installer menu items.
WARNING: Setting this to 1 will reload the factory
defaults and clear the channel list including erasing any
assigned Channel Icons and Labels.
Set to 0 for set by program.
Set to 1 for 4:3.
Set to 2 for 16:9 (Factory Default).
Set to 4 for Zoom 1
Set to 5 for Zoom 2
(Continued from previous page)
Clonable Menu Features
Channel
Auto Program (Active
channels found with
the channel search)
Channel Labels
Channel List
Fine Tune
Picture
Mode
Contrast
Brightness
Color
Sharpness
Tint
Color Temperature
Screen Format
Film Mode
Sound
Mode
Treble
Bass
Balance
Auto Volume
Multi-Track
Internal Speaker
Setup
Time
Clock
Auto Off
V-Chip
TVPG Rating
MPAA Rating
Menu Language
SET ID
Caption
On/Off
Analog Mode
Digital Mode
Digital Font Option
Reference: TV Features / Menus that can be Cloned
*Note:
For Digital Font Options, if any default setting is left unchanged prior to cloning, then all the digital font options will be set to default settings. If
you want custom digital font options to be clonable, set all digital font options to settings other than Default.
PAGE 59
PAGE 60
Reference: Procedures for adding Channel Label Icons/Custom Channel Labels
(2-5-4 + MENU Mode)
Adding Channel Icons and Labels in the 2-5-4 + Menu Mode
Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu
Editing/Adding Channel ICONs and/or Labels
If there is no pre-assigned ICON, you can make a channel label of up
to 7 characters to help in identifying the channel or network.
At your option, channel labels can also be added in addition to a
pre-assigned ICON. You may also add labels for the Aux input sources
to clearly identify the devices that are connected to the Aux inputs.
Editing and adding the labels can only be done if there are
channels entered into the TV/STB’s channel map either by
using the method described in item 6 (page 52), by cloning or
by the use of the master remote control from the PPV provider.
To Do Channel Editing/Labeling, proceed as follows
1. Enter TV/STB Installer menu.
2. After the installer menu appears, press ‘2’, ‘5’, ‘4’, ‘MENU’.
This enters the channel label edit mode.
Add your channel icons and channel labels in this menu,
see below. (You can do this more than once.)
3. To exit the menu when done press “MENU”.
•CHANNEL Up/Down - Tunes in the next channel in scan.
•Left/Right Arrows - Select the item to change. If “I” is shown,
the ICON can be changed. If a number is shown, it indicates the
position of the character that can be changed.
•Up/Down Arrows - Select the ICON or the character to be
displayed.
•0 – 9 - Use to enter the index number of the ICON, if known.
•OK (Enter/Select) - Changes the ICON after the number has been
entered.
•TV/AV - Changes the Aux input source for labeling. This key is
located on the side of the TV front and on Installer remote
control.
•MENU - Exits the labeling/editing menu.
Changing a Channel’s ICON on Master
TV
1. With Channel Up/Down, select the channel
you want to change the Icon for.
2. With the Right or Left ADJ arrow, select
the letter ‘I’ on the channel ID display.
3. With the Up or Down arrow, select the
desired ICON you want to appear to
identify the channel. (If you know the
ICON number, enter the number followed
by Enter / Select.)
Note: If no Icon is available, leave at or
select the default blank icon display.
4. Proceed with Changing/Adding Labels or
go to the next channel.
Changing/Adding Channel Labels on
Master TV
1. Channel Up/Down to select the desired
channel.
2. Press the Right or Left ADJ arrow
repeatedly until the numbers 1 to 7 show
up. The number shows the position of the
character that can be changed. Number 1
is the first character, number 2 the second
character and so on.
3. With the Up or Down arrow, select the
desired character.
4. Proceed to the next number position or
use Channel Up/Down to go to the next
channel.
Changing Source Labels on Master TV
1. Press “TV/AV” to select the desired Aux
input source; Video 1, Component, S-Video
etc.
2. Press the Right or Left arrow repeatedly
until the numbers 0 to 9 show up.
The number shows the position of the
character that can be changed.
3. Use the Up or Down arrows to select the
desired character.
4. Press “TV/AV” for the next Aux source or
proceed with Changing Icon or
Changing/Adding Labels.
1234567
XYZ
XYZ
XYZ
NETWORK
(Label)
(Icon)
Reference: Detailed Information For Making A Master TV
IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...
To set up a master TV you will need to know how to
enter the TV/STB Installer menu and make changes to
the default values as required. If necessary, familiarize
yourself with the TV/STB Installer menu and how to
make and save changes in the menu, beforeattempting to clone the
TV/STB Master TV setup.
You will also need an Installer remote control similar to the one
shown in the front of this manual.
Finally, the TV’s clonable features need to be set up. This is a
critical step. If the Master TV display panel’s clonable features like
adding channel icons or channel labels are not correctly added, then
the cloned TV/STB will all have problems.
As the cloning procedure is being performed, specific steps need to
be done at the indicated times to achieve the desired result. Be sure
to do each task as indicated. If a procedure or step is left out or not
performed completely, cloning may not work. At each step, pay
attention to assure the TV screen shows the proper message when
cloning. If the message indicated does not appear, there is a
problem with that step and cloning may not be successful. Cloning
is only possible when the signal source is an Analog channel, not a
digital channel.
Making a Master TV
Detailed Instructions
The following describes the procedure for preparing a Master TV/STB
for cloning and the procedure for adding Channel Icons and/or
Labels.
Note 1: Disconnect all Aux inputs. Under certain conditions, Auto
Program Scan is disabled if there is an Aux input active.
Note 2: Under certain conditions, changes to the input mode of the
RGB inputs will not take effect until the power is cycled (TV is
turned Off and On). To avoid confusion, disconnect all RGB inputs
before entering the Installer menu.
1. Enter the TV/STB installer menu.
a. Reset the internal controller to factory default by accessing
installer menu item 117 FACT DEFAULT, set it to 1 and press
“ENTER”. The value will change back to 0 after the TV’s internal
controller has been restored to factory default condition.
b. Within the Installer menu, set the Installer menu items to the
configuration required of your institution.
c. It is important to set the tuning band at this time, see
Installer menu item 03 BAND/AFC.
d. Set Installer menu item 28 – CH OVERIDE to 001 to allow
access to the Auto Program and Channel List/Channel Label
features in the Channel Menu. Exit the Installer menu.
2. Access the Master TV menus and set the clonable options on the
menus to the desired configuration. Refer to the Clonable Menu
Features Chart.
3. Run Auto Program.
4. Enter the Channel List/Channel Label menu and edit the channel
line-up to include the Free-To-Guest Channels only.
5. Assign ICONs to the channels using the Channel Label Menu.
Note: You can add Channel ICONS typically network logos like
ABC, NBC, PBS etc. in this step. Or, in Step 7, add Channel ICONS
or labels for channels without Icons.
6. Transfer the TV setup: Enter the TV/STB installer menu.
Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to
the TV/STB. Once the transfer is complete, the system will exit
the Installer menu.
Note: Only do 2-5-5 + MENU once. The TV setup may be
corrupted if 255 + Menu is done more than one time.
7. Edit/Add Channel ICONs and Channel Labels as needed.
Enter Installer menu. With menu displayed, press 2-5-4 + MENU.
See page 51 for detailed instructions:
- Editing/Adding Channel ICON and Labels on Master TV
- Changing a Channel’s ICON on Master TV
- Changing/Adding Channel Labels on Master TV
- Changing Source Labels on Master TV
8. Verify Master TV setup and feature configuration:
• Did you add Channel ICONS?
• Did you add Channel Labels?
• Did you add Aux Source Labels?
• Did you adjust all TV menu options as required?
The TV master setup is now ready to be cloned. Go to the master
TV cloning section or continue on to page 51.
After verifying master setup, enter the TV/STB Installer menu
and set Installer menu item 028 Ch Overide to 000.
PAGE 61
PAGE 62
Reference: Software Version Check
Procedure to Check Software Version
The software version of the TV/STB may be checked by accessing the INSTALLER MENU. To do this, press the MENU button at least 10 times
until the menu display ceases to respond to MENU key presses.
Then, press "9", "8", "7", "6", "OK (Enter/Select)".
Typical Installer Menu
HCS5610XX PTC INSTALLER MENU
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 CPU V1.01.00
TV/STB Aux Input Configuration
TV/STB Aux Input Configuration
DIRECT ACCESS
Tuning
OLD_OCV
=0
130 90
Video2
(Front) CV ONLY
34 CAMPORT_EN 0x01 0
Video Front
(Camport) 0(VIDEO) 2
Video Front
(Camport)
131 91
Video1(Rear)
CV ONLY
DTV/PC Auto
39 REAR_AUX_EN 0x02 1
Rear Video
(Aux) 0(VIDEO) 1
Rear Video
(Aux)
132 92
Component2
91 YPrPb2_EN 0x04 2
S-Video
Rear 0(VIDEO) 5
S-Video
Rear
133 93
DVI/HDMI1
35 COMPPORT EN 0x08 3
Front
Computer 0(VIDEO) 3
Front
Computer
DTV/PC Auto
137 97
HDMI2
36 FRNT Y C_EN 0x80 7
Front
S-Video 0(VIDEO) 8
Y-C Front
Video
DTV
PC
134 94
RGB1
87
REAR RGB EN=1
REAR RGB EN=2
0x10 4
SVGA Rear
Computer
0(VIDEO)
2(PC) 4
SVGA Rear
Computer
135 95
RGB2
92 RGB2 ENABLE 0x20 5
NTSC Rear
Computer 7
NTSC Rear
Computer
136 96
Component1
38 YPrPb EN 0x40 6
Rear
YPrPb
component
video
0(VIDEO) 6
Y/UV
Component
OLD_OCV
=1 Source Input
Source Mode Number Value ValueLabeling LabelingLabeling
TV/STB
ENABLE
Installer Menu
MPI DATA
STATUS TYPE
0x41 SOURCES
ENABLED (R/W)
DATA STATUS
TYPE 0xD2
CURRENT AV
SOURCE (R)
DATA
STATUS
TYPE 0X0D
AUX
SOURCE
(R)
MPI DATA
STATUS
AUX
SOURCE
ASSIGNMENT
0(VIDEO)
2(PC)
DTV
PC
PAGE 63
PAGE 64
TV/STB RS-232 Monitor Requirements / RS-232 Troubleshooting
Type of Connector; D-Sub 9-Pin Female
Monitors listed below require RS-232 Null Modem DB9 Cable
with male connectors at each end. Depending on the type of
Null modem cable, one or two gender changers may be required.
3-Wire Configuration
(Serial male-male NULL modem cable)
RS-232C Null Configuration
Monitors listed below require RS-232 straight-through (extension)
DB9 cable with male connector on one end and female
connector on the other end.
Refer to monitor installation guide for more specifics.
RS-232 Pin Configuration Wiring Diagram
of the TV/STB Display Control Connector
RS-232 Communication Requirments
No. Pin Name
1No Connection
2TXD (Transmit data)
3RXD (Receive data)
4No Connection
5GND
6No Connection
7No Connection
8No Connection
9No Connection
5
2
1
3
4
1
2
3
4
5
6
7
8
9
NC
TXD
RXD
NC
GND
NC
NC
NC
NC
TV/STB
D-Sub 9-pin
Male
D-Sub 9-pin
Male
Monitors:
M3200C
M3700C
M4200C
M4600C
M3201C
M3701C
M4201C
M4210C
1
2
3
4
5
6
7
8
9
NC
TXD
RXD
NC
GND
NC
NC
NC
NC
Monitor
Null-Modem
Cable
3-Wire Configuration
(Straight-through male-female cable)
RS-232C Straight Configuration
1
2
3
4
5
6
7
8
9
NC
TXD
RXD
NC
GND
NC
NC
NC
NC
TV/STB
D-Sub 9-pin
Male
D-Sub 9-pin
Female
Monitors:
20LS7DC
26LC7DC
23LS7DC
32LC7DC
37LC7D
42LC7D
47LC7DF
32LC2DC
37LC2DC
50PC5DC
50PM1M
MU-60PZ95V
71PY1M
1
2
3
4
5
6
7
8
9
NC
RXD
TXD
GND
NC
NC
NC
NC
NC
Monitor
Straight-Through
or Extension
Cable
Improper RS-232 Communications Setup
-Selects Incorrect Source at Power Up
TV/STB powers On TV. Flashes selected HDMI/DVI source but
selects incorrect Aux source.
-Check settings for Installer menu items 108, 109, 110 and 113.
-Displays ‘No Signal’ message at Power Off
TV/STB does not power Off TV and displays ‘No Signal’ message.
-Check settings for Installer menu items 108, 109, 110 and 113.
RS-232 Troubleshooting
RS-232C Control
Use this method to connect several products to a single PC.
You can control several products at a time by connecting them to a single PC.
Connecting the cable
Connect the RS-232C cable as shown in the picture.
-The RS-232C protocol is used for communication between the PC and product. You can turn the product on/off, select an input source or
adjust the OSD menu from your PC.
*The Product transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if
the data is data read mode, it indicates present status
data. If the data is data write mode, it returns the data
of the PC computer.
Communication Parameter
Baud Rate : 9600bps (UART)
Data Length : 8bits
Parity Bit : None
Stop Bit : 1bit
Flow Control : None
Communication Code : ASCII code
RS-232C Cable
(not included)
PC
STB
COMMAND1 COMMAND2 DATA(Hexa)
Key M C Key Code
[Command2][ ][Set ID][ ][OK][Data][x]
OK Acknowledgement
*The Product transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
Data 1: Illegal Code
2: Not supported function
3: Wait more time
[Command2][ ][Set ID][ ][NG][Data][x]
Error Acknowledgement
*[Command 1]: First command.
*[Command 2]: Second command.
*[Set ID]: You can adjust the set ID to choose desired product
ID number in Special menu. Adjustment range is 0 ~99
When selecting Set ID ‘0’, every connected
TV set is controlled. Set ID is indicated as decimal
(0~99) on menu and as Hexa decimal (0x0~0x64)
on transmission/receiving protocol.
*[DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
*[Cr]: Carriage Return
ASCII code ‘0x0D’
*[ ]: ASCII code Space (0x20)’
Transmission / Receiving Protocol
[Command1][Command2][ ][Set ID][ ][Data][Cr]
Transmission
PAGE 65
PAGE 66
RS-232C Control
Data Key code : Refer to page A18.
[m][c][ ][Set ID][ ][Data][Cr]
Transmission
[c][ ][Set ID][ ][OK][Data][x]
Acknowledgement
G To send IR remote key code.
1. Key(Command : m c)
Code(Hexa) Function Note
00 Channel Up Button
01 Channel Down Button
02 VOL(+) R/C Button
03 VOL(-) R/C Button
C4 POWER ON Discrete IR Code(Only Power On)
C5 POWER OFF Discrete IR Code(Only Power Off)
09 MUTE R/C Button
10 Number Key 0 R/C Button
11 Number Key 1 R/C Button
12 Number Key 2 R/C Button
13 Number Key 3 R/C Button
14 Number Key 4 R/C Button
15 Number Key 5 R/C Button
16 Number Key 6 R/C Button
17 Number Key 7 R/C Button
18 Number Key 8 R/C Button
19 Number Key 9 R/C Button
5A AV1 Discrete IR Code(Input AV1 Selection)
D0 Video2 Discrete IR Code(Input Video2 Selection)
D3 S-Video2 Discrete IR Code(Input S-Video2 Selection)
D8 S-Video1 Discrete IR Code(Input S-Video1 Selection)
BF Component1 Discrete IR Code(Input Component1 Selection)
D4 Component2 Discrete IR Code(Input Component2 Selection)
D5 RGB-PC Discrete IR Code(Input RGB-PC Selection)
D7 RGB-DTV Discrete IR Code(Input RGB-DVD Selection)
CE HDMI1 Discrete IR Code(Input HDMI1 Selection)
CC HDMI2 Discrete IR Code(Input HDMI2 Selection)
0E SLEEP R/C Button
44 Enter (OK) R/C Button
79 ARC R/C Button
76 ARC(4:3) Discrete IR Code(Only 4:3 mode)
77 ARC(Full) Discrete IR Code(Only Full mode)
AF ARC(ZOOM) Discrete IR Code(Only Zoom mode)
4C Dash(-) R/C Button
1A Flash back R/C Button
39 closed captions R/C Button
PAGE 67
Troubleshooting
Troubleshooting
Symptoms Possible Cause(s) Possible Solution(s) See Page(s)
Software Corrupted.
Virtual and Physical
channels appear in
channel scan w/Channel
Up/Down.
Can not direct enter
channel number
Channel not included in
channel scan in TV controller.
After 2-5-5 + MENU, only channels included in TV controller will appear.
If channel is available it cannot be added to channel scan. Rerun Auto
Program.
2-5-5 + MENU not performed. After Auto Program and Channel List, etc. press 2-5-5 + MENU to
transfer channels and TV setup to internal TV controller. Afterward,
only Physical or only Virtual channels will appear in digital channel
scan, analog channel scan will be normal.
2-5-5 + MENU performed
more than once.
Start all over with item 117 and Enter then redo Auto Program, Channel
List, etc. *Note: 2-5-4 + MENU can be done more than once.
48
48
48
Software Problems
Ch Overide set to 000 Only channels in memory can be tuned in.
Some quick and easy tips to resolving problems
Display Panel Picture
No Power. See troubleshooting flow chart. 69
Power
No Picture. • Display panel is turned off. -Turn TV on.
-Power failure?
• Antenna/Cable not connected. -Connect Antenna/Cable signal source to TV/STB.
• Connections incorrect. -Check connections on TV/STB.
• M.P.I. not connected. -If applicable, connect M.P.I. cable to M.P.I. device.
• Encrypted program. -Try another channel.
• Wrong tuning band. -Adjust Installer menu settings.
11~12
10~17
53~58
Erratic Operation
Installer menu setup. • Wrong Installer menu settings. -Adjust Installer menu settings as required.
• Software problem. -Remove TV power cord for 15 seconds.
53~58
Remote Control
Remote doesn’t work. • Remote not in TV mode. -Use Mode key to select TV; puts remote into TV/STB mode.
• Not aimed at IR remote sensor. -Point remote at TV’s IR receiver on TV.
• Remote too far from IR sensor. -Move remote closer to TV’s IR receiver or darken room.
• IR path to TV’s receiver obstructed. -Remove obstructions.
• Weak batteries. -Replace batteries.
• Wrong battery polarity. -Check that “+” and “-” match in battery compartment.
• Too much light in room. -Dim room light.
• Wrong Installer remote control. -Requires compatible Installer remote, contact your LG dealer.
• Incorrect Bed 1-2 setting. -Set correct Bed 1-2 setting.
20~21
48
20
Picture Reception
Normal picture, poor
or no sound.
• Audio muted. -Press MUTE or use Volume Up key to increase sound level.
• Broadcast problem. -Try a different channel.
20~21
20~21
Broadcast Tuning Mode Digital Channel OSD
No Information
available display.
*Note: For other problems not caused by the TV/STB, refer to other devices’ operating guide.
•Item 103 set to 1
physical channels tuning.
-Set Item 103 to 0 for information to be added to virtual
channel tuning digital OSD.
55~58
PAGE 68
Reference: Cloning Procedure Troubleshooting
• Procedure interrupted.
• Different TV models.
• Step(s) omitted or not performed.
• Insufficient cloning time.
• Cloning erratic.
- Wait until procedure complete message is displayed.
- Cloning is only possible with identical model TVs.
- Reread 50 - 51 - 52 pages to be sure all tasks were performed.
- Redo cloning and be sure learning/teaching time is about 1 min. and
5 to15 seconds (75 seconds).
- Reset Clone Programmer.
Warning: Do not use LT2002 while a LodgeNet PPV
card is installed in TV or clone programmer will be
damaged.
Reset Clone After Static Shock
After replacing exhausted batteries, or if the programmer
behaves strangely after a static shock, activate the
internal reset switch and restore normal operation.
After a reset, check the real-time clock setting. It may
be necessary to reset the Clone Programmer clock from a
TV containing the correct time.
Note
The LT2002 programmer is designed to be used with TVs con-
taining the 221-01006 and later processors. Use with earlier TV
sets may give unpredictable results. Processors used before the
221-01006-04 have a limited screen display capability. They
cannot display entire screens as shown in the quick setup
instructions accompanying the LT2002 clone programmer. Use
the printed menu illustrations on the quick setup sheet supplied
with the Clone as an aid to making your programming choices.
(Although the menus are not all displayed, the clone functions
all operate normally.)
Clone Programmer Troubleshooting
Clone Programmer
Cloning Notes: While clone is copying or transferring a master setup, do not touch or otherwise disturb clone or connections between clone
and TV. Cloning a master TV setup should take at least 45 seconds. Transferring the master TV setup to the target TV should take at least 45
seconds. Monitor LED on clone to assure that the blinking heartbeat pattern is present throughout clone operations. After cloning, be
sure to disconnect power from the target TV for about 15 seconds.
Problem Possible Cause(s) Possible Solution(s)
Remote does not
operate clone.
• Wrong Installer remote. - Only use an appropriate Installer remote to operate clone program-
mer with TV/STB.
LED does not blink. • M.P.I. cord not connected.
• TV/STB not turned on.
• Weak batteries.
- Connect M.P.I. cord.
- TV/STB must be powered On for clone to work.
- Install 4 fresh AA high-quality alkaline batteries.
Clone menu hard to
read.
• Weak signal. - Connect TV/STB to a reliable Analog channel signal source.
No time set. • Time not available. - Set time on a TV, copy time to Clone Programmer.
Clone not working. • Clone programmer problem. - Try a different LT2002 Clone programmer.
- Reset Clone Programmer.
Clone Scans Channels
more than once.
•Clone should only scan
channels once.
- Retry cloning again.
Master and Other TV/STB
Cloning did not work.
Clone time disappeared. • Batteries were removed. - Batteries must remain installed to retain time settings.
New Setup not present. • TV/STB not reset. - Disconnect newly cloned unit from power for 5 seconds.
• After cloning operations are complete, just unplug the LT2002 from the TV/STB.
• If the TV/STB does not display a picture on the TV (blank screen) after a few seconds, just change channels.
Troubleshooting Flow Chart
PAGE 69
PAGE 70
Installer Quick Setup Guide
See the installation and setup guide of the particular TV for more information.
*Note: After installing a Pay-Per-View card, be sure to remove and reconnect the TV/STB
AC power cord.
Instructions for Making a Master TV/STB Setup
1. Connect TV/STB to signal source, connect power cords and turn on.
2. Enter the TV/STB installer menu.
*Note: If this is not a new setup, set Installer item 117 to 001 and press Enter to
reset TV to default condition.
• Set Tuning Band.
Set Installer menu item 003 BAND/AFC to CATV: 001, Broadcast: 000 etc.
• If necessary, set Installer menu item 028 CH OVERIDE to 001.
In addition, set any other installer items as required of your system.
Exit Installer menu.
3. Access the Master TV menus and set the clonable options on the menus to the
desired configurations. Refer to the Clonable Menu Features Chart for the TV.
(Picture, Sound, Time etc.)
4. Do a Channel Search; run Auto Program. (aka EZ Scan.)
5. Enter the Channel Edit menu and delete channels per your requirements.
6. Enter the Channel Label menu and assign ICONs to the channels.
*Note: You can add Channel ICONStypically network logos like ABC, NBC, PBS etc. in
this step. Or, in Step 8, add Channel ICONS or custom text labels for channels which
Icons are available for.
7. Transfer the TV setup. After all menu options and features are set to your
requirements, enter the installer menu. Press ‘2’,‘5’, ‘5’, ‘MENU’ to start the transfer
of the TV’s setup to the PTC.
After the transfer is complete, the system will exit the Installer menu.
8. Set any Channel Labels as needed.
a. Enter Installer menu.
b. Press ‘2’, ‘5’, ‘4’, ‘MENU’ to enter the menu. In this menu edit the assigned
channel Icons, assign custom text labels for channels and assign labels for active
Aux sources. Press ‘Menu’ to exit.
9. Enter the Installer menu. Set item 028 Ch Overide to 000 and exit menu.
HCS5610XX PTC INSTALLER MENU
117FACT DEFAULT 00X
003 BAND/AFC 00X
028 CH.OVERIDE 001
028 CH. OVERIDE 000
000 INSTALLER SEQ 000
UPN 000-000-000-000 FPGA 09F1
PTC V1.00.000 STB V1.01.00
WXYZ
DIGITAL 19-3
MONO SAPSTEREO
WXYZ
ANALOG 2
MONO
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
RJP
INTERFACE
REMOTE
IN
AUDIO IN AUDIO OUT RS-232C
DISPLAY
CONTROL
AUX
CONTROL
DIGITAL
VIDEO OUT
AC IN
DIGITAL AUDIO
OUT (OPTICAL)
AC OUT
DIGITAL
VIDEO IN
MAX 8A 960W AC 120V~ 60Hz
12
Antenna
Wall Jack
AC Power
Cord
RF Coaxial
Wire (75ohm)
Connections Panel
Mode
Color Temperature
Standard
G
Contrast
Brightness
Sharpness
Color
Tint
Screen Format
Noise Reduction
Film Mode
11:20 PM
Sep.11, 2006
DEMove GSelect MENU Back
Antenna
Auto Program G
Channel Label
Channel List
Fine Tune Auto
Signal Strength
11:20 PM
Sep.11, 2006
--:-- --
--. -- ----
DEMove OK Select MENU Back
Antenna
Auto Program
Channel Label
Channel List
Fine Tune
Signal Strength
MENU Back
Digital Output
PCM G
Auto Volume
On
Multi-Track
English
11:20 PM
Sep.11, 2006
DEMove OK Select MENU Back
Glossary of Terms
A list of definitions for some of the words found in this guide
75 OHM RF CABLE
The wire that comes from an off-air antenna or
cable service provider. The end looks like a
hex-shaped nut with a wire sticking through
the middle. It screws onto the Antenna/Cable
threaded jack on the back of the TV/STB.
300 TO 75 OHM ADAPTER
A small device that connects a two-wire 300
ohm antenna to a 75 ohm RF jack.
They are usually about an inch long with two
screws on one end and a round opening with a
wire sticking out on the other end.
ANALOG TELEVISION
Standard television broadcasting format in 4:3
picture aspect ratio.
A/V CABLES
Audio/Video cables. Three cables bunched
together—right audio (red), left audio (white),
and video (yellow). A/V cables are used for
stereo playback of videocassettes and for
higher quality picture and sound from other
A/V devices.
A/V DEVICE
Any device that produces video or sound (VCR,
DVD, cable box, or television).
AMPLIFIER
An electronic device that amplifies sound from
a television, CD player, VCR, DVD, or other
Audio/Video device.
ANTENNA
The physical receiver of television signals sent
over the air. A large metal piece of equipment
does not always have to be visible to be using
an antenna.
CABLE
Cable service box. Refers to the descrambler
box cable subscribers use to receive cable
programming signals.
CATV
Programming provided by a cable service.
DIGITAL TELEVISION
High-resolution, cinema-quality television
signals transmitted digitally.
DVI
Digital Video Interface
Accommodates analog and digital interfaces
with a single connector.
COMPOSITE VIDEO
Typical video jack, uses one wire for
transporting three-color video signals.
COMPONENT VIDEO
Uses three wires for transporting three-color
video signals. The end result is usually better
video quality.
DELETED
Lets you remove channels from the list that the
end user can scroll through using CH (Channel)
Up/Down.
HDMI
High-definition multimedia interface.
HDTV
High-definition television. Refers to television
signals that have higher resolution than
ordinary analog TV signals.
HDSTB
High-definition set top box. Refers to a tuner
device that receives high-definition television
signals which have higher resolution than
ordinary analog TV signals.
INPUT
Refers to the input jack that receives a signal
from a TV, VCR, DVD Player or other
Audio/Video device.
JACK
An input or output connector on the back of a
TV, VCR, DVD Player or other Audio/Video
device.
MONO SOUND
Mono (monaural) sound is one channel of
sound. On more than one speaker, all the
speakers play the same audio.
OUTPUT
Refers to the output jack that sends a signal
out of a VCR, DVD, or other A/V device.
PHYSICAL CHANNEL NUMBER
Actual digital major, dashed minor channel
number that a station is broadcasting on.
RGB (Red, Green, Blue)
Connection input or output port available for
producing a video image using three separate
colors: Red, Green, and Blue.
2ND AUDIO PROGRAMMING/SAP
Second Audio Programming (SAP) is another,
separate audio channel available with some
programming. Choosing SAP often refers to
listening to audio in another language, such as
Spanish or French.
SIGNAL
Picture and sound traveling through a cable, or
over the air, to the TV.
STEREO SOUND
Stereo (Stereophonic) sound refers to audio
that’s divided into right and left sides.
TUNER
Device that picks up the broadcast signal and
turns it into picture and sound.
VIRTUAL CHANNEL NUMBER
The arbitrarily assigned digital dashed minor
channel number that a station is broadcasting
on.
PAGE 71
Zenith HD Commercial Interface STB Warranty
For Customer Support/Service
Please call:
1-888-865-3026
www.zenith.com
www.lgcommercial.com
P/NO : 3350GDKM0017D GPN08MA039A
Welcome to the LG family! We believe that you will be pleased with your HD Commercial Interface STB. Please read this warranty
carefully, it is a “LIMITED WARRANTY” as defined under Federal Law. This warranty gives you specific legal rights, and you may also
have other rights that vary from state-to-state within the U.S.A.
HD Commercial Interface STB
One year parts and labor from date of purchase or delivery date.Warranty Term
Warranty begins on the date of delivery of the HD Commercial Interface STB.
For your convenience, keep the dealer’s dated bill of sale or delivery ticket as evidence of the purchase date.
Effective Warranty Date
Read the Installation and Setup Guide carefully so that you will understand the operation of the HD Commercial Interface STB and
how to adjust the controls.
Installation Guide
Reception problems caused by inadequate antenna or faulty antenna connections are the owner’s responsibility.Antenna
For warranty service information, Call 1-888-865-3026. Parts and service labor that are LG’s responsibility (see above) will be
provided without charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty ser-
vice, call 1-888-865-3026.
You must provide the model number, serial number and date of purchase or date of original installation.
Warranty Service
New or remanufactured replacements for factory-defective parts may be used. Such replacement parts are warranted for the remain-
ing portion of the original warranty period.
Parts
Warranty service is provided at LG. Customer pays for shipping charges to LG, LG pays for return shipping charges to return HD
Commercial Interface STB to customer. Call 1-888-865-3026 for further information.
Warranty Service
This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or repair
of antenna systems, cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse,
negligence, acts of God or other causes beyond the control of LG. Any alteration of the product after manufacture voids this war-
ranty in its entirety.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRAN-
TY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND LG SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL,
INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PROD-
UCT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU.
Not Covered
LG’S RESPONSIBILITY
OWNER’S RESPONSIBILITY
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.
2000 Millbrook Drive, Lincolnshire, IL 60069.
© Copyright 2008 LG Electronics U.S.A., Inc.
