Zero Energy Solutions YB25301 Amplified Zigbee module User Manual CC2530PA A1 Module

Download:
Mirror Download [FCC.gov]
Document ID	3029024
Application ID	r5vAgw12eJ9Lcs4o+UwolQ==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	116.93kB (1461630 bits)
Date Submitted	2016-06-15 00:00:00
Date Available	2016-06-15 00:00:00
Creation Date	2012-03-28 22:45:16
Producing Software	GPL Ghostscript 8.70
Document Lastmod	2016-06-15 01:07:37
Document Title	CC2530PA-A1 Module
Document Creator	PDFCreator Version 0.9.9
Document Author:	Administrator

Zero Energy Solutions LTD.
YB2530+PA+LNA Wireless Module V2.0
General description
The YB2530+PA+LNA Wireless Modle is a low-power,hightly integrated 2.4GHz transcevier
that suitable for systems targeting compliance with worldwide radio-frequency. It’s a
true system-on-chip solution for 2.4-GHz IEEE802.15.4, ZigBee and RF4CE applications.
Features
2.4-GHz IEEE802.15.4 compliant RF transceiver
Programmable output power up to 20dBm
Accurate digital RSSI/LQI support
Suitable for systems targeting compliance
with wordwide radio-frequency
Data rate: 250kbps
256KB in-system programmable flash
Two 128 bytes FIFO for TX & RX buffer
CSMA/CA hardware support
Battery monitor and temperature sensor
AES security coprocessor
8KB RAM with retention in all power mode
32-kHz sleep timer with capture
Wide Supply-Voltage Range (2 V–3.6 V)
Applications

 2.4-GHz IEEE 802.15.4 systems

 RF4CE remote control systems (64-KB flash and higher)

 AMR – Automatic Meter Reading

 Two-way RKE – Remote Keyless Entry

 Home and building automation

 Wireless alarm and security systems

 Industrial monitoring and control

 Wireless Light Dimming

 The PCB antenna is disabled and will never be used

 Wireless sensor networks
working with outside antenna
Electrical Characteristics
ITEM
TEST REQUIREMENT
Voltage supply
2.0－3.6V
Center frequency
2405－2480MHz
Frequency error
±50KHz
Modulation
O-QPSK
Output power
0-20dBm
Programmable
Receiving
sensitivity
-116dBm
@250Kbps data rate
Receiving current
<32mA
Transmitting
current
160mA
Po=20dBm
Sleep consumption
0.4mA
Power Mode 1
Data rate
250kbps
Transmit distance
1000M
Antenna
50ohm
Store temperature
-40－125°C
Operation
temperature
Package size
-20－85°C
REMARKS
DC
Programmable
At open area
Base on crystal
performance
23.2*34mm
Ta = 25°C, VCC = 3.3V
Typically, equipment utilizing this device requires emissions testing and
government approval, which is the responsibility of the equipment
manufacture.
Dimensions and Layout size
Controlling the RF PA
The two digital control pins ( PAEN,LNAEN ) have functional as below,
CC2530 P1.1 Connect to PAEN of the PA chip
CC2530 P1.4 Connect to LNAEN of the PA chip
 Transmit mode
PAEN logic 1, LNAEN logic 0
 Receive mode
PAEN logic 0,LNAEN logic 1
 Idle mode PAEN logic 0,LNAEN logic 0
Design References
1. Texas Instruments Low-Power RF Web site has all our latest products, application and
design notes, FAQ section news and events updates, and much more. Just go to
www.ti.com/lprf.
2. IEEE Std. 802.15.4-2006: Wireless Medium Access Control (MAC) and Physical Layer
(PHY) Specifications
http://standards.ieee.org/getieee802/download/802.15.4-2006.pdf
3. For IAR software,demo code,docments etc. over 700MB files,more than 300 members
in QQ group 255430047.
Regulatory information for the OEMs and Integrators
The guidelines described within this document are provided to OEM integrators installing Amplified
Zigbee module in notebook and tablet PC host platforms. Adherence to these requirements is necessary
to meet the conditions of compliance with FCC rules, including RF exposure. When all antenna type and
placement guidelines described herein are fulfilled the Amplified Zigbee module may be incorporated
into notebook and tablet PC host platforms with no further restrictions. If any of the guidelines described
herein are not satisfied it may be necessary for the OEM or integrator to perform additional testing
and/or obtain additional approval. The OEM or integrator is responsible to determine the required host
regulatory testing and/or obtaining the required host approvals for compliance
. Amplified Zigbee module are intended for OEMs and host integrators only.
. The Amplified Zigbee module must be operated with an access point that has been approved for the
country of operation.
. Changes or modification to Amplified Zigbee module by OEMs, integrators or other third parties is not
permitted. Any changes or modification to Amplified Zigbee module by OEMs, integrators or other third
parties will void authorization to operate
Information to Be Supplied to the End User by the OEM or Integrator
The following regulatory and safety notices must be published in documentation supplied to the end user
of the product or system incorporating the Amplified Zigbee module, in compliance with local regulations.
Host system must be labeled with "Contains FCC ID: 2AHI9YB25301 ", FCC ID displayed on label.
The Amplified Zigbee module must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product. Intel Corporation is not
responsible for any radio or television interference caused by unauthorized modification of the devices
included with the wireless adapter kit or the substitution or attachment of connecting cables and
equipment other than that specified by Intel Corporation. The correction of interference caused by such
unauthorized modification, substitution or attachment is the responsibility of the user. Intel Corporation
and authorized resellers or distributors are not liable for any damage or violation of government
regulations that may arise from the user failing to comply with these guidelines.
This device has been evaluated and shown compliant with the FCC RF Exposure limits under fixed
exposure conditions (antennas are greater than 20cm from a person’s body)when installed in certain
specific configurations.
The host system shall have a label showing: Contains FCC ID: 2AHI9YB25301
The product used Reverse helix rubber ducky antenna.if you select other type antenna, you need nother apply.
(The gain of antenna : 3.0dBi)
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
15.105 Information to the user.
(b) For a Class B digital device or peripheral, the instructions furnished the user shall include the following or
similar statement, placed in a prominent location in the text of the manual:
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator
and your body.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are
firmware programmed at the factory to match the intended destination.
The firmware setting is not accessible by the end user.
The final end product must be labelled in a visible area with the following:
“Contains Transmitter Module 2AHI9YB25301”

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 5
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Producer                        : GPL Ghostscript 8.70
Keywords                        : 
Modify Date                     : 2016:06:15 01:07:37+08:00
Create Date                     : 2012:03:28 22:45:16+08:00
Creator Tool                    : PDFCreator Version 0.9.9
Metadata Date                   : 2016:06:15 01:07:37+08:00
Document ID                     : 57dee434-7b40-11e1-0000-5d8863f7ebbc
Instance ID                     : uuid:e31ad821-f2e9-41ed-b289-8125d81c50d0
Format                          : application/pdf
Title                           : CC2530PA-A1 Module
Creator                         : Administrator
Description                     : 
Description (x-repair)          : 
Author                          : Administrator
Subject                         : 

EXIF Metadata provided by EXIF.tools