Zero One Technology Co WU04001 WIRELESS PRINT SERVER User Manual 615WU English Manual V0

Download:
Mirror Download [FCC.gov]
Document ID	529459
Application ID	tdwTw+np6yjbpDwghE6WZQ==
Document Description	USERS MANUAL 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	88.82kB (1110215 bits)
Date Submitted	2005-04-07 00:00:00
Date Available	2005-04-07 00:00:00
Creation Date	2005-03-30 06:20:08
Producing Software	Acrobat Distiller 5.0.5 (Windows)
Document Lastmod	2005-03-30 14:32:21
Document Title	615WU English Manual V0.pdf
Document Creator	PScript5.dll Version 5.2
Document Author:	Weng

V0.2.32 Draft version, for evaluation sample only.
5. Configuration from Embedded Web Server
Overview
The Print Server contains an embedded web server that can be accessed through a
supported web browser on a LAN, for example, IE 4.0, Netscape 4.0 or above is
recommended.
The embedded web server provides access to configuration and management pages for the
print server and the connected peripheral device.
Using Embedded Web Server
Before you can use the embedded web server, the print server must be configured with an IP
address. There are many ways to configure the print server’s IP address. For example, the
Windows-based of PSAdmin utility can easily set an IP address with the print server, please
see the Properties – TCP/IP options of chapter 3.
After an IP address is established on the print server, perform the following step:
Status Menu
Once you have finished the IP address configuration with print server. You should be use
web browser to view and management the print server. The status menu of the print server
helps administrator control the print server’s System, Printer, NetWare, TCP/IP, SNMP and
AppleTalk of status for the time being.
Preparation
Enter the print server’s IP address in the Address field of your Web browser. Press Enter.
Then the print server page will appear. From here you can configure all print server settings.
Please follow this information in the status menu of the print server:
System Status
1.Click Status, it then appears the sub-menu.
2.Click System, it then as shown in the following picture.
32
V0.1.32 Draft version, for evaluation sample only
Device Name: This option allows you to view device name of the print server. To correct the
print server’s device name.
System Contact: This option allows you to view contact name of the print server. To check
the print server’s contact name who in charge of this device.
System Location: This option allows you to view Location name of the print server. To
confirm the print server’s location name where the print server is located
in the office’s LAN.
System Uptime: This option allows you to view uptime of the print server. When you start
the print server, it will compute the print server from start time to power off
time.
Firmware Version: This option allows you to view firmware version of the print server. To
verify the print server’s firmware version is newer in this time.
MAC Address: This option allows you to view Node ID of the print server. The Node ID is
unique from any print server.
Printer Status
1.Click Status, it then appears the sub-menu.
2.Click Printer, it then as shown in the following picture.
33
V0.2.32 Draft version, for evaluation sample only.
Manufacturer: This option allows you to view manufacturer of the printer. When the printer
connected with the print server, it will be show in the manufacture box.
Model Number: This option allows you to view model of the printer. When the printer
connected with the print server, it will be show in the model box.
Printing Language Supported: This option allows you to view command to set the printer.
When the printer connected with the print server, it will be
show in the command box.
Current Status: This option allows you to view status of the printer. When the printer
connected with the print server, it will be show in the status box. For
Example, Waiting for job. It is means the printer already to printing.
LPR Queue Name: This option allows you to view queue name of print server when you
want to use the network printing via LPR setting.
Wireless Status
1.Click Status, it then appears the sub-menu.
2.Click Wireless, it then as shown in the following picture.
34
V0.1.32 Draft version, for evaluation sample only
Mode: This option shows the wireless operation mode of your print server.
Type: Infrastructure or ad-Hoc mode.
AP’s MAC Address: This option shows the MAC address of Access Point that associated
with print server.
SSID: The SSID of your wireless network.
Channel Number: Current channel number.
Data Transmit Rate: Current transmit rate.
WEP Encryption: The status of WEP encryption.
802.11X (EAP): This option shows the 802.11X (EAP) is enabled or disabled.
TCP/IP Status
1.Click Status, it then appears the sub-menu.
2.Click TCP/IP, it then as shown in the following picture.
35
V0.2.32 Draft version, for evaluation sample only.
Use DHCP/BOOTP: This option allows you to view DHCP/ BOOTP status. If there is a
DHCP/BOOTP server on your network, this option allows the print server
to obtain IP-related settings automatically from your DHCP server.
IP Address: This option allows you to view IP address from the print server. The IP address
must meet the IP addressing requirements of the network segment.
Subnet Mask: This option allows you to view subnet mask from the print server. The IP
address must meet the IP addressing requirements of the network segment.
Gateway’s IP: This option allows you to view gateway from the print server. This IP address
of gateway must meet the router or gateway to go across of the network segment.
Netware Status:
1. Click Status, it then appears the sub-menu.
2. Click Netware it then as shown in the following picture.
36
V0.1.32 Draft version, for evaluation sample only
General Settings:
Print Server Name: This option allows you to view print server’s name would be configured
by PSAdmin utility.
Polling Time: This option allows you to view polling time from the print server. This function is
search for NetWare Server by per time.
NetWare NDS Setting:
Use NDS Mode: Enable or Disable.
Name of the NDS Tree.
Name of the NDS Content.
Current Status: Connect or Disconnect.
NetWare Bindery Setting:
Use Bindery Mode: Enable or Disable.
Name of the File Server:
Current Status: Connect or Disconnect.
SNMP Status
37
V0.2.32 Draft version, for evaluation sample only.
1.Click Status, it then appears the sub-menu.
2.Click SNMP, it then as shown in the following picture.
SNMP Communities: This option allows you to view SNMP communities from the print
server. There are two communities that control message from the
network management of the print server.
SNMP Traps: This option allows you to view SNMP traps from the print server.
AppleTalk Status
1.Click Status, it then appears the sub-menu.
2.Click AppleTalk, it then as shown in the following picture.
38
V0.1.32 Draft version, for evaluation sample only
Zone Name: If no any zone exists, the print server itself displays the zone name as an
asterisk (*) in the current AppleTalk Status of the print server in the web
browser.
Port Name: -xxxxxx-1, where xxxxxx represents the last six digits of the print
server’s Node ID.
Printer Type: This option allows you to view printer type from the print server. If you are
using a PostScript printer you can select the LaserWriter 8 icon from your Mac
computer.
Data Format: This option allows you to view data format from the print server. If you are
using a PostScript printer you can select ASCII, TBCP or BCP format from
web configuration.
Setup Menu
Meanwhile, you have finished the IP address configuration with print server. You should use
web browser to configure the print server. The setup menu of the print server helps
administrator to setup the print server’s System, Printer, NetWare, TCP/IP, SNMP and
AppleTalk.
Preparation
Enter the IP address of the print server as the URL, for example, 192.168.10.132. Then the
print server’s home page will appear in content of the web browser.
Please follow this information in the setup menu of the print server:
System Setup
39
V0.2.32 Draft version, for evaluation sample only.
1.Click Setup, it then appears the sub-menu.
2.Click System, it then as shown in the following picture.
Device Name: This option allows you to input device name of the print server. To correct the
print server’s device name.
System Contact: This option allows you to input contact name of the print server. To check
the print server’s contact name who in charge of this device.
System Location: This option allows you to input Location name of the print server. To
confirm the print server’s location name where the print server is located
in the office’s LAN.
Password: This option allows you to input setup password of the print server. When you
select setup menu of web configuration from the print server, it then as shown in
the following picture.
Re-type Password.
ԦUser Name: You must be input the default administration user name, admin as login user
name.
40
V0.1.32 Draft version, for evaluation sample only
ԦPassword: The default password is empty. After setup password is completed from the
print server, you shouldn’t forget this password.
Wireless Setup:
1.Click Setup, it then appears the sub-menu.
2.Click Wireless, it then as shown in the following picture.
Basic Settings:
Mode: Infrastructure or 802.11b Ad-Hoc mode.
Select SSID or Manually Enter SSID Below: You can use Site Survey to help you assign a
SSID or input in manually.
Channel: Specify a Channel number that meet your environment.
Data Transmit Rates: Choose the transmit rate of your wireless print server.
41
V0.2.32 Draft version, for evaluation sample only.
Advanced Settings:
To avoid the unexpected problem, please use these default value.
WEP Settings:
Use WEP: 64 or 128-bit..
Key Format: Alphanumeric or Hexadecimal.
WEP key: Input your WEP key in this field.
Printer Setup
1. Click Setup, it then appears the sub-menu.
2. Click Printer, it then as shown in the following picture.
LPR Queue Name: This option allows you to define the queue name of the print server’s port
when you want to use the LPR printing.
TCP IP Setup:
1. Click Setup, it then appears the sub-menu.
2. Click TCP/IP, it then as shown in the following picture.
42
V0.1.32 Draft version, for evaluation sample only
DHCP/BOOTP: This option allows you to select DHCP/ BOOTP option. If there is a
DHCP/BOOTP server on your network. This option allows the print server
to obtain IP-related settings automatically from your DHCP server.
IP Address: This option allows you to input IP address from the print server. The IP address
must meet the IP addressing requirements of the network segment.
Note:
On the TCP/IP Setup screen, specify a fixed IP address is highly
recommended.
Subnet Mask: This option allows you to input subnet mask from the print server. The IP
address must meet the IP addressing requirements of the network segment.
Gateway: This option allows you to input gateway from the print server. This IP address of
gateway must meet the router or gateway to go across of the network segment.
NetWare Setup
1.Log into your NetWare file server as a Supervisor (Admin.) or equivalent.
2.Select NetWare and type in the Print server that created during PCONSOLE Select the
NetWare File Server to which the print server device will be attached.
3.Click Setup, it then appears the sub-menu.
4.Click NetWare, it then as shown in the following picture.
43
V0.2.32 Draft version, for evaluation sample only.
Print Server Name: This option allows you to input print server name which configured by
PSAdmin utility or PCOMSOLE program.
Polling Time: The time interval in which the print server unit polls the file server for servicing
of print queues.
Logon Password: This option allows you to input encrypted password from the print server.
The print server login to NetWare server that administrator set password
from selected print server.
NDS Mode: To Enable NDS Mode, if you want to setup NDS environment. To select Tree
Name of NetWare then input context name in the Context box.
Bindery Mode: To Enable Bindery Mode, if you want to setup Bindery environment. To
select File Server Name of NetWare.
44
V0.1.32 Draft version, for evaluation sample only
Installing Print Server on NetWare 4.x/5.x
Due to its architecture and functionality, the print server must work under NetWare 4.x/5.x
NDS Bindery Emulation. When you install the NetWare file server for the first time, by default,
the installation program will automatically set up the Bindery Emulation function for you by
adding “SET BINDERY CONTEXT =” in the AUTOEXEC.NCF file. By default, the bindery
context will only be set on your organization (O) object.
If you have ever modified this line, or if you have ever added any organization units (OU) to
your NDS tree after the NetWare system was installed, please read the following section
before you install the print server.
For the purpose of illustration, we assume the NDS tress structure is as follows:
[ROOT]
(O)ABC
(OU)ABC-USA
(OU)Sales
Admin
FileServer-1
(OU) Tech
Installation Procedure
1. At your file server console, type “load install”.
2. Select “NCF files options”.
3. Select “Edit AUTOEXEC.NCF file”.
4. Add or Modify the “SET BINDERY CONTEXT =” line to include the NDS organization (O)
and all organization unit (OU) objects where users are located. For example: SET
BINDERY
CONTEXT
O=ABC;
OU=SALES.OU=ABC-USA.O=ABC;
OU=TECH.OU=ABC-USA.O=ABC ;
5. When done, save the new AUTOEXEC.NCF file. Please restart your NetWare file server
in order for new settings to take effect immediately.
6. Next, please refer to “Auto Setup” section in this chapter to finish installing your print
server.
7. Log into your NetWare file server as a Supervisor (Admin.) or equivalent via a Bindery
connection.
8. Run NetWare’s PCONSOLE and add users to the “Queue Users” list.
9. From your NetWare client computer, such as Windows 95/98/Me, create a printer that is
connected (redirected) to the NetWare print queue serviced by the print server.
45
V0.2.32 Draft version, for evaluation sample only.
Note: Please refer to NetWare’s Print Server/Services manuals for detailed PCONSOLE
commands.
SNMP Setup
TCP/IP networks use a standard management protocol called Simple Network
Management Protocol (SNMP). SNMP is widely used in the industry as a solution for remote
network management and monitoring of networking devices. SNMP actually includes a
protocol, a database structure specification, and a set of database objects. The database
objects are contained in a standard database called Management Information Base (MIB)
that is stored on the networking device called SNMP agent. The print server's SNMP
implementation runs in a TCP/IP environment.
A host on the network running Network Management System (NMS) software can
access the print server device by reading and writing the MIB objects stored in the device.
The Network Management Systems are available from many third-party vendors, such as
Hewlett-Packard's OpenView.
When accessing (traversing) MIB objects in the print server using NMS software called
SNMP manager, you need to provide a community name in each SNMP request for
authentication purpose. The print server supports up to two community names. The default
community name is public (case-sensitive), with Read Only access right in default.
When an unusual condition or activity occurs, the SNMP agent alerts the SNMP
manager through SNMP traps. Following list summaries SNMP trap messages that the print
server will send out.
Activities/SNMP Trap Messages
Description
Link Up or Link Down
When the network interface on the print server fails, a link down
trap message is generated; if the network interface comes back
to life, a link up trap message is sent.
Cold Start or Warm Start When the print server restarts, the cold start or warm start trap
message is generated.
Authentication Failure
When the print server received a SNMP request with a
community name that does not match the community name the
print server is configured with (stored in the print server's
memory), an authentication failure trap message is generated.
In the print server's SNMP implementation, the following MIB objects are available for
updating.
MIB Object Names
system.sysContact
Description
Indicates the network administrator's name.
46
V0.1.32 Draft version, for evaluation sample only
system.sysName
Indicates the print server's name for identification.
system.sysLocation
Indicates the location of the print server.
snmp.snmpEnableAuthenTraps
Enables or disables the function of sending SNMP Authentication
Failure trap message to the network administrator, if the
community name within a SNMP request is not correct.
Users can set up print server’s SNMP functions by using their browsers.
1.Click Setup, it then appears the sub-menu.
2.Click SNMP, it then as shown in the following picture.
SNMP Community: The print server supports up to two community names. The default
community name is public (case-sensitive), with Read Only access
right in default.
Support HP WebJetAdmin: This option allows user determine to disable/enable the
Support HP WebJetAdmin.
47
V0.2.32 Draft version, for evaluation sample only.
SNMP Traps: Enable the function of sending SNMP Authentication Failure trap message to
the network administrator, if the community name within a SNMP request is
not correct.
AppleTalk Setup
The print server can print jobs submitted from Macintosh workstations connected to an
Ethernet using AppleTalk protocol. The basic configuration is for the print server in an
AppleTalk environment is performed simply by opening the Chooser window and selecting a
printer that is connected to the print server.
1.Click Setup, it appears the sub-menu.
2.Click AppleTalk, it as shown in the following picture.
3.Zone Name: In this option, type an AppleTalk Zone name that you want the print server to
belong to or leave it in default (This enables the print server automatically search and link
itself to the default zone that is set on the AppleTalk router, if found). We also assume that
at least an AppleTalk Zone exists on the network. If no any zone exists, the print server
itself displays the zone name as an asterisk (*) in the current AppleTalk Status of the print
server in the web browser.
4.Port Name: In this option, type a name for identification purpose or just leave it in default
(recommended).
Note: The default print server’s Chooser name is as shown as follows:
-xxxxxx-1, where xxxxxx represents the last six digits of the device’s
Node ID. For example: ATALK_PS-40EEED-1. You may also change the  to
48
V0.1.32 Draft version, for evaluation sample only
a name you like for identification purpose in this option. The print server will append the last
six digits to the name you specify.
5.
Printer Type: In this option, the LaserWriter of printer type by default
(recommended).
6.Data Format: In this option, data format includes ASCII, TBCP and BCP.
Setting Up a Macintosh Computer
1.
At a Macintosh computer, from the Apple menu, select Chooser.
2.
The Chooser window then displays an Apple Zone list. Select the Zone name that you
specified when configuring the PRINT SERVER.
Note: If you select a Zone that the PRINT SERVER doesn’t belong to, as you specified in the
previous section, no print server will be displayed in the Step 4.
3.
If you are using a PostScript printer you can select the LaserWriter 8 icon.
4.
The Chooser window then displays PRINT SERVER (s) featuring the support for
AppleTalk protocol, along with its default Chooser Name in the right-hand Select A
PostScript Printer dialog box.
Note: 1.You may change the default Chooser name and Zone name of a PRINT SERVER by
using your web browser before proceeding with this installation. Please see the
previous section in this chapter for details.
2. If you use Mac OS 8.x or 9.x, please make sure your printer support PostScript.
5.
Click Setup… button and choose the PPD file matching your printer, and click OK. If
your printer does not appear in the PPD file list, please contact your printer vendor. You
may also use the Generic PPD if you do not need any printer specific features.
6.
Close the Chooser Windows.
7.
Done.
49
V0.2.32 Draft version, for evaluation sample only.
6. Network Print Monitor
Preparation
The print server supports TCP/IP, IPX/SPX and NetBEUI protocols under Windows
95/98/Me. Please make sure that the following steps have been completed before
proceeding with installation under Windows PC.
Select A Desired Protocol
TCP/IP
The TCP/IP Protocol must be installed. For further information, please read “TCP/IP
Protocol Installation” section in this chapter.
Note: If TCP/IP protocol is chosen, please refer to “Assigning an IP Address to the print
server” section later in this chapter.
IPX/SPX
The IPX/SPX-compatible Protocol must be installed. For further information, please read
“IPX/SPX-compatible Protocol Installation” section in this chapter.
NetBEUI
The NetBEUI protocol must be installed. For further information, please read “NetBEUI
Protocol Installation” section in this chapter.
50
V0.1.32 Draft version, for evaluation sample only
TCP/IP Protocol Installation
1. Click Start, point to Settings and select Control Panel.
2. Double click the Network icon.
3. If the TCP/IP Protocol is not already installed, click Add.
4. Select Protocol and click Add.
5. Select Microsoft from the Manufacturers list.
6. Select TCP/IP Protocol from the Network Protocols list.
7. Specify an IP address, Subnet Mask, and Gateway address or specific “Obtain IP
address automatically”, if a DHCP server is available on the LAN.
8. Restart the computer.
9. Done.
Note: Using TCP/IP protocol to access the print server requires well-configured TCP/IP
settings. If you are not familiar with these settings, please consult your network
administrator for details or ask for help.
IPX/SPX-compatible Protocol Installation
1. Click Start, point to Settings, and select Control Panel.
2. Double click the Network icon.
3. If the IPX/SPX-compatible Protocol is not already installed, click Add.
4. Select Protocol and click Add.
5. Select Microsoft from the Manufacturers list.
6. Select IPX/SPX-compatible Protocol from the Network Protocols list and follow the
instructions on the screen.
7. Restart the computer.
8. Done.
51
V0.2.32 Draft version, for evaluation sample only.
NetBEUI Protocol Installation
1. Click Start, point to Settings, and select Control Panel.
2. Double click the Network icon.
3. If the NetBEUI is not already installed, click Add.
4. Select Protocol and click Add.
5. Select Microsoft from the Manufacturers list.
6. Select NetBEUI from the Network Protocols box and follow the instructions on the
screen.
7. Restart your computer for new settings to take effect.
8. Done.
Note: For more detailed information, please refer to your Microsoft Windows
9X/ME/NT/2000/XP/2003 manuals.
Win 95/98/Me/NT/2000/XP/2003 Installation Procedure
Please perform the steps as follows to ensure a smooth installation:
1. Run Setup from the print server’s NetWare, Win 95/98/Me/NT/2000/XP/2003 Setup
diskette
2. The Network Print Monitor for Windows 95/98/Me Setup will then appear. Click Next.
3. A message reading, “Setup is complete. You may add the Network Print Port by using
the PSAdmin” will appear. Click OK.
4. Click Start, point to Settings, and select Printers.
5. Double-click the Add Printer icon.
6. Select Local Printer and click Next.
7. Select the appropriate printer manufacturer and printer type and click Next.
8. Select LPT1 and click Next.
9. Type in the Printer Name and click Next.
52
V0.1.32 Draft version, for evaluation sample only
10. A message reading, “After your printer is installed, Windows can print a test page so you
can confirm that the printer is set up properly.” Select No and click Finish.
11. Double-click the newly created Printer Name icon.
12. Select Printer and Properties.
13. Click Details tab and select Add Port.
14. In the Add Port dialog box, select Other, as shown in the following picture.
15. Select the Network Print Port and click OK.
16. The Add Port box will then appear, along with the print server’s Node ID (The last 6 digits
of the Node ID, located on the back of the print server unit). Select one printer server port
from the list, which is now connected to (one of) your printer(s), as shown in the following
picture.
53
V0.2.32 Draft version, for evaluation sample only.
„By default, the computer will first search for the print server(s) on the network by using
the IPX/SPX protocol.
„If the IPX/SPX protocol is installed, the print server will be displayed along with its Node
ID, as shown in Node column. (The last 6 digits of the Node ID, located on the back of the
print server unit). Select one of the print server’s ports from the list.
„If the IPX/SPX protocol is not installed, no print server will be shown in the display box.
Then please select TCP/IP or NetBEUI alternatively.
„It starts again to search for the print server on the network by using the protocol you
specify in the step above. When finished, the print server will be displayed along with the
its Node ID, as shown in the following picture. (The last 6 digits of the Node ID, located on
the back of the print server unit). Select one of the print server’s ports from the list.
Uninstalling Network Print Port on Windows 95/98/Me/NT/2000/XP/2003
To provide users an easiest way to remove all of the Network Print Port components from
Windows 95/98/Me, the Network Print Port software comes with un-installation wizard
program to help users remove the software components from their Windows
95/98/Me/NT/2000/XP/2003 systems in minutes. Please follow the directions listed below to
proceed with the un-installation procedure.
After the Network Print Port is removed, the print server is no longer accessible via the
Network Print Port. You have to re-install the Network Print Port on your system in order to
access the print server again.
Procedure:
1. Click Start, point to Settings, and select Control Panel.
2. Double click the Add/Remove Programs icon.
3. Click Add/Remove tab.
4. Select Network Print Monitor for Windows 95/98/Me and click Add/Remove button.
5. The un-installation wizard program will be launched.
6. Follow the directions on the screen to complete the un-installation procedure.
Note: We recommend you restart your computer after un-installation is finished.
54
V0.1.32 Draft version, for evaluation sample only
7. TCP/IP LPR Port Printing Installation
Basic TCP/IP Installation Overview
When installing your print server in a TCP/IP environment, IP addresses are essential as a
basic means of communications. It is therefore necessary to first assign an IP address to
your print server unit. After assigning an IP address, the print server can be configured
accordingly.
Assigning an IP Address
The first step to install a print server on a TCP/IP network is to assign the print server an IP
address and other related TCP/IP settings before the print server can function. You can
select the following two methods to specify an IP address the print server. Each method will
be detailed in the following section.
1. Use the Network Print Monitor utility.
2. Manually specify (using DOS commands or UNIX text-mode commands. This
applies to Windows NT/2000/XP/2003 and UNIX systems).
Note: The Network Print Monitor can only search for the print server(s) over the same
network segment the Windows NT/2000/XP/2003/UNIX computer is located. You
would like to install a print server on a different network segment.
DHCP
The print server supports DHCP feature, allowing the print server to obtain an IP address and
related TCP/IP settings automatically from a DHCP server. While the print server supports
DHCP, we strongly recommend you manually specify a fixed IP address to the print server.
By default, the print server’s DHCP function is disabled.
Windows NT LPR Port Printing Installation
1. Click Start, point to Settings, and select Printer.
2. Run Add Printer.
3. The Add Printer Wizard screen will appear, Select My Computer and click Next.
4. Click Add Port.
55
V0.2.32 Draft version, for evaluation sample only.
5.
From the Printer Ports box as shown in the following picture, select the LPR Port.
6. The Add LPR compatible printers box will then appear as shown in the following picture.
Type in the IP address assigned to the print server in the Name or address of server
providing lpd box.
7. In the Name of printer or print queue on that server box, type in a printer name, for
example, lp1. Click OK.
8. In the Printer Ports box, select Close.
9.
Click Next.
10. Select the appropriate printer manufacturer and printer type list and click Next.
11. Select Shared. Type in a new Share Name or leave it in default and click Next.
12. A message reading, “After your printer is installed, Windows can print a test page so you
can confirm that the printer is set up properly.”, Select Yes (Recommended) and click
Finish.
13. Done.
56
V0.1.32 Draft version, for evaluation sample only
Windows 2000/XP/2003 Standard TCP/IP Port Printing Installation
1.
Click Start, point to Settings, and select Printer.
2.
Run Add Printer, Click Next.
3.
The Add Printer Wizard screen will appear, Select Local Printer and click Next.
4.
From the type of Create a new port box as shown in the following picture, select the
Standard TCP/IP Port, Click Next and Next.
5.
The Add Standard TCP/IP Printer Port Wizard box will then appear as shown the picture
as below, and type in the IP address assigned to the print server in the Printer Name
or IP Address box, Click Next.
57
V0.2.32 Draft version, for evaluation sample only.
6.
In the Add Standard TCP/IP Printer Port Wizard box as shown in the following picture,
Select Custom, Click Settings button, and click Next.
7.
In the Configure Standard TCP/IP Port Monitor box as shown in the following picture,
select LPR form Protocol, type in a queue name, for example, lp1.
8.
Click OK, and Next.
Note: Please DO NOT type any other name than lp1 in this step.
9.
Click Finish.
58
V0.1.32 Draft version, for evaluation sample only
10. Select the appropriate printer manufacturer and printer type list and click Next.
11. Type in a new Printer name or leave it in default, and click Next button.
12. A message reading, “To confirm that the printer is installed properly, you can print a test
page”. Select Yes (Recommended) and click Finish.
13. Done.
59
V0.2.32 Draft version, for evaluation sample only.
UNIX Installation
After the static IP address is assigned, the Print Server is ready to be configured. For some
UNIX/Linux systems, we include the detailed installation procedures below. If you can’t find
the installation procedure corresponding to your UNIX system, please refer to your UNIX
manuals for details about configuring your UNIX for the “remote printing system”.
SCO UNIX 8.0.0 (Caldera Open Unix 8.0.0)
1. Select “SCO Admin”.
2. Select “Printer Setup Manager”.
3. Enter /Printer / Add TCP / IP Printer…
4. Name: Input a name you like. For example: Test.
Protocol Type: Choose “lpd (BSD)”.
Make/Model: Select the printer model. For example: EPSON LQ570.
Printer Connection Type: Choose “On Remote Server”.
Remote System: Input the IP address of the printer server. For example: 192.168.1.250.
Remote Printer: lp1 or lp2 or lp3. (fixed)
If the printer connected to the first print server port, please choose lp1.
If the printer connected to the second print server port, please choose lp2.
If the printer connected to the third print server port, please choose lp3.
5. Click “OK”.
6. Enter /Printer / Make Default.
System V Release 4 Unix
1. For example: the print server has a static IP address: 192.168.1.100
2. Input “lpsystem –tbsd 192.168.1.100”.
3. Input “lpadmin –pa1 –s 192.168.1.100!lp1”. lp1 for the first print server port.
4. Input “accept a1”.
5. Input “enable a1”.
60
V0.1.32 Draft version, for evaluation sample only
Redhat Linux 9
The Print Server can work under any Linux-based systems, including Slackware, RedHat,
etc, without any problems.
Basically, the Linux's printing system is based on BSD system. Although many commercial
Linux systems are available in the market and their commands will vary slightly, depending
upon which version is used, the functionality of the Linux-based variants is exactly the same.
Following are the outlined procedures (recommended for all users) on Red Hat Linux
7.2/7.3 or later with X-Window system installed.
a. Make sure that the TCP/IP is well configured on your RedHat system, including
network interface card's driver and IP-related settings say, IP address, subnet mask,
and gateway IP).
b. Log in root.
c. Assign Print Server an IP address. At shell mode:
c.1. arp -s  < Print Server
's Node ID>
c.2. Execute tftp < Print Server 's IP> get config.txt and quit tftp.
c.3. Edit the config.txt and modify the IP address, subnet mask, and gateway IP.
When done, save the config.txt.
c.4. Execute tftp  put config.txt and quit tftp.
d. Start X-windows by typing startx at the shell mode.
e. Open Printer Configuration.
f. Click New button.
61
V0.2.32 Draft version, for evaluation sample only.
g. Click Forward button.
h. In the Name field, type a user-defined name, click Forward.
62
V0.1.32 Draft version, for evaluation sample only
i.
In the Queue Type field, choose Networked UNIX.
j. In the Server field, type the IP address of print server
k. In the Queue field, type a print server’s port name, which connect to the printer. For
example: lp1.
l. Click Forward button.
m. In the Printer field, choose Postscript Printer.
63
V0.2.32 Draft version, for evaluation sample only.
n. Choose the model of printer and click Forward.
o. Done.
64
V0.1.32 Draft version, for evaluation sample only
8.Upgrading Print Server
Overview
Upgrading print server will allow you to upgrade its firmware inside the print server while the
newer software version of the print server is available from your local dealer. Depending on
the different systems users might use, this chapter is divided into several Sections; please
refer to the following lists for your systems.
1.
Upgrading the print server from PSAdmin
2.
Upgrading the print server from Windows NT/2000/XP/2003
3.
Upgrading the print server from UNIX system
4.
Upgrading the print server from WEB browser
Note: 1.Before you proceed to upgrade the print server, please ensure that the necessary
binary file is located on your current working directory.
2.Before upgrading the print server, ensure that it is not printing jobs. You have to wait
until the print job is finished before you can proceed.
3.Be careful not to interrupt the file transfer. If the transfer is interrupted, the print
server may have to be re-initialized by your dealer.
Upgrading the print server from PSAdmin
1. Log into your NetWare file server as a Supervisor (Admin.) or equivalent.
2. Ensure binary file is located in the PSAdmin directory.
3. Run PSAdmin from your Windows PC.
4. Click the Upgrade icon on tool bar.
Upgrading the print server from Windows NT/2000/XP/2003 (Through
TCP/IP)
1. Ensure binary file is located in your current working directory.
2. At NT/2000/XP/2003’s DOS prompt, and type “tftp –i  put
mpsXX.bin “.
65
V0.2.32 Draft version, for evaluation sample only.
3. Wait for the transfer successful message.
4. Done.
Upgrading the print server from UNIX (Through TCP/IP)
1. Log in as root
2. Ensure binary file is located in your current working directory.
3. Type “tftp ”.
4. At tftp prompt, type “get upgrade”.
5. Change to binary mode.
6. At tftp prompt, type “put mpsXX.bin”.
7. Wait for the file transfer to complete.
8. Quit from tftp.
9. Done.
Upgrading the print server from Browser
1.
Ensure binary file is located in your current working directory.
2.
Enter the IP address of the print server as the URL.
3.
Click Misc, and then choose Upgrade From Browser, it then as shown in the following
picture.
4.
Click Browse… and select the firmware file.
66
V0.1.32 Draft version, for evaluation sample only
5.
Click Upgrade.
6.
Done.
67
V0.2.32 Draft version, for evaluation sample only.
9. Troubleshooting
General Troubleshooting Overview
The most common problems, which cause the print server to perform improperly, are
covered in this chapter. If a problem still exists after reading this chapter, please contact your
dealer for technical support.
LED Light Indicators
The print server is equipped with LED lights to assist in diagnosing problems that are the
result of the network and/or the print server hardware itself.
Status (Green)
When the print server unit is powered on, the Status LED will flash five times as part of the
unit’s Power On Self Test (POST). This indicates that the print server hardware is properly
configured.
Note: Make sure that the LED flashes five times (POST) upon connecting the power. If the
unit does not flash five times, contact your dealer for a replacement or repair.
WLAN (Green)
Data is being transmitted via the wireless connectivity.
USB (Green)
Data is being transmitted via the USB port.
Power Related Problems
The print server requires an external AC power adapter in order for it to function. If you have
a power problem, check to see whether the power cord or its connectors are damaged. More
importantly, check to see that the AC power adapter included with the print server matches
the AC voltage in your country or area. Using an incorrect AC adapter will damage your print
server.
68
V0.1.32 Draft version, for evaluation sample only
Print Port Related Problems
Printing data failure may be caused by a loose connection of the print server to the USB port
of the printer. Check to see if any of the pins on the USB connector are damaged. In addition,
check the cable connection. If the pins are damaged, contact your dealer for a replacement
connector.
Windows 95/98/Me/NT/2000/XP/2003 Troubleshooting
Multi-Segment LAN Environment Installation (through the Network Print Port)
If your print server and Windows 95/98/Me/NT/2000/XP/2003 are located on two different
segments, and your Windows NT server is used as the router/gateway you will need to
implement the following procedures in order for your print server to function properly:
Add the RIP for NWLink IPX/SPX compatible transport. See RIP for NWLink IPX/SPX
compatible transport Installation Procedure later in this section.
Add the frame type 802.2 for both Ethernet adapters. See Multi-Segment Frame Type
802.2 Installation later in this section.
RIP for NWLink IPX/SPX compatible transport Installation Procedure
1. From your Windows NT server that is used as a router, select Start from the bottom left
hand corner of the screen.
2. Select Settings.
3. Select Control Panel.
4. Double-click the Network icon.
5. Select Services.
6. Select Add.
7. In the Select Network Service box, select the RIP for NWLink IPX/SPX compatible
transport. Click OK.
8. Follows the directions on the screen.
9. Done.
Multi-Segment Frame Type 802.2 Installation
1. From your Windows NT server that is used as a router, select Start from the bottom left
hand corner of the screen.
2. Point to Settings, and select Control Panel.
3. Double-click the Network icon.
4. Select Protocols.Select the NWLink IPX/SPX Compatible Transport.
5. Select Properties.
6. Select your (first) network interface card and select Manual Frame Type Detection.
7. Click Add.
8. In the Frame Type field, select Ethernet 802.2.
9. In the Network Number field, type in an unique 8-digit hexadecimal network number.
For example: 12345ABC.
10. Select Add.
11. Repeat the Steps 8-12 for the other Ethernet adapter.
69
V0.2.32 Draft version, for evaluation sample only.
12. Restart the computer.
13. Done.
Moving the print server to A New Segment
If the print server is moved from one network segment to another after the initial installation,
through the Network Print Port, the print server must be reconfigured on the original Windows
NT server or on each Windows 95/98 computer using this print server in order for the print
server’s driver on each computer to re-establish a new connection.
Print Server Reconfiguration Procedure on Windows 95/98/Me
1. Click Start on the bottom left hand corner of the screen.
2. Select Settings and select Printers.
3. Select your printer connected to the print server, and right-click the printer icon. Select
Properties.
4. Click Details tab.
5. Click Port Settings as shown in the picture below. The print server will be displayed on
the next print server’s configuration screen.
Find your original print server according to its Port Name or other distinguished name and
click this print server.
6. Click OK and it returns to the printer’s Properties page.
7. Click OK.
8. Done.
Print server Reconfiguration Procedure on Windows NT
1. Click Start on the bottom left hand corner of the screen.
2. Select Settings and select Printers.
3. Select your printer connected to the print server, and right-click the printer icon. Select
Properties.
4. Click Ports tab.
5. Click Configure Port. The print server will be shown on the next screen.
6. Find your original print server according to its Port Name or other distinguished name
and click this print server.
7. Click OK and it returns to the printer’s Properties page.
8. Click OK.
70
V0.1.32 Draft version, for evaluation sample only
9. Done!
Moving Your Computer to A New Segment
If you are using the print server through the Network Print Port on your NT or Windows
95/98/Me computer and your computer is going to be moved onto another segment, you
have to reconfigure the print server on your computer to use your print server. However, this
situation is like moving the print server to a new segment. Please refer to the “Moving the
print server to a new segment” section for more detailed reconfiguration instructions.
Novell NetWare Troubleshooting
Many printing problems can be traced back to incorrect or incomplete print server
installations. It is always wise to check the installation configurations first.
In some cases, if necessary, delete the print server, print queue(s) or other setting(s). Next
recreate the necessary parameters or reconfigure the print server by running the PSAdmin.
TCP/IP Troubleshooting
When you are configuring a new print server on your NT/UNIX server through LPR Port
printing under TCP/IP protocol, you might encounter the following problem in your initial
installation steps:
" I can do the "arp" command. However, when I am going to ping or tftp the print server, it
always shows Request timed out. I have checked the print server’s power and it exactly
passed the POST. Besides, the network cabling is OK. As such, I can't do tftp command to
get and put the print server's configuration file and save its IP address permanently. I can't,
therefore, continue installing the print server."
Regarding this problem, there are three possible causes:
A. The print server's Node ID you specified in the "arp" command is not correct.
If this is the case, please ensure the Node ID field in the corresponding entry of the print
server's IP address in NT's ARP cache table is correct by typing the following command at
NT's DOS prompt. "arp -a"
If the Node ID shown on the screen doesn't match the print server's Node ID, please follow
the instructions below to reset the entry.
1.
At NT's DOS prompt, type "arp -d " to delete the current
entry.
2.
Type "arp -s  " to specify a new ARP entry.
3.
Refer to Chapter 7 for the detailed instructions to complete the installation.
71
V0.2.32 Draft version, for evaluation sample only.
B. The print server's IP address is duplicated or is as same as another computer's IP
address on the network.
If this is the case, please consult your network administrator to obtain an unused IP address
for your print server.
C. The print server is on one segment and your Windows NT server is on the other
segment.
(This troubleshooting guide will also apply to a multiple-segmented network while installing
the print server)
For example, assuming the print server is on Segment A, NT server is on Segment B, and
there is a gateway computer between Segment A and Segment B. The network might be a
complete TCP/IP network, or a hybrid of TCP/IP and IPX/SPX network.
If this is the case, you have to adopt the following steps, depending on which platform the
gateway computer is.
a.If the gateway computer is a NT/UNIX server:
You have to do the same "arp" command to specify an entry on the NT/UNIX computer as
a gateway in order for it to forward your subsequent "ping" or/and "tftp" commands to the
print server.
b.If the gateway computer is a Novell NetWare file server:
1.Due to the presence of this NetWare file server, the IPX/SPX protocol might be used on
your network. Therefore, we strongly suggest you run the PSAdmin from any client
computer and select "Manual Setup" to specify the print server's IP address (For more
detailed information about Manual Setup, please refer to Chapter 3).
2.If the solution described above is not applicable, you have to follow the instructions
below to set up the print server's IP address.
For the purpose of explanation, we assume the NT server is on Segment A and its IP address
is 192.72.214.66 (subnet mask: 255.255.255.224), the print server is going to be installed on
Segment B, with IP address, for example, 192.72.214.100.
1. Find an unused IP address on Segment A for temporary use in the following steps, for
example, 192.72.214.68.
2. Connect your print server to Segment A as a networked node.
3. On your NT server, type, for example, "arp -s 192.72.214.68 00-40-01-3F-02-AB". Please
note, in this arp command you have to type 192.72.214.68 on purpose. Do not type this IP
address as 192.72.214.100.
4. Type "tftp 192.722.214.68 get config.txt". The configuration file will then be retrieved and
transferred to your NT server.
72
V0.1.32 Draft version, for evaluation sample only
5. Type "edit config.txt" to modify this configuration file.
6. In your editor, modify "BoxIPAddress" field from "0.0.0.0" to "192.72.214.100". Leave
other options as default and do not change their values. When done, save this new
file and quit from your editor. Please note, in this step you must specify an IP address
which is valid on Segment B, such as 192.72.214.100 in this example, rather than
192.72.214.68.
7. Type, for example, "tftp 192.72.214.68 put config.txt" to save this new configuration back
to print server.
8. Move the print server back to the Segment B.
9. Done!
73
V0.2.32 Draft version, for evaluation sample only.
Appendix:
Diagnostic Mode (Wireless)
If you have no the twisted-pair cable to configure print server and have problems to configure
it on wireless network. Please refer to the following steps:
1. Change the print server to diagnostic mode by switching the DIP switch to DIAG mode.
2. Change your wireless adapter to 802.11b Ad-hoc mode, and the ESSID: WLAN-PS;
Channel: 6
3. Run PSAdmin to discover the print server.
4. Select the wireless print server
5. Select wireless and input the ESSID, Channel, Rates that meet your network
environment, then press ok.
74
V0.1.32 Draft version, for evaluation sample only
6. Done! The print server will restart.
7. Switch the DIP back to normal mode and change your wireless adapter setting.
Reset Button
Reboot the Print server:
1. Verify the power of print server is turned on.
2. Press the reset button once.
WARNING: This will restart the print server and stop all on-going and pending
print jobs!
Perform a Factory Default:
1. Disconnect the external power adapter.
2. Hold down the reset button.
3. Reconnect the external reset button. Wait about 5 seconds.
4. Release the reset button.
5. The print server will restart.
75
V0.2.32 Draft version, for evaluation sample only.
WARNING: This will erase all settings of print server to default and should be
performed with caution! After performing a factory default, the default settings
will be:
z802.11b Ad-Hoc mode
zSSID: WLAN-PS
zChannel: 6
zNo WEP encryption
zDHCP client: Off
zIP address: 192.168.0.10
76
V0.1.32 Draft version, for evaluation sample only
Frequently Asked Questions
Question A
Print jobs are sent to the print queue successfully, but fail to be sent to the printer.
Possible explanations
1. The Print server Name/Print Queue configuration in PCONSOLE is incorrect.
2. The Print server name specified and stored in the print server memory doesn’t match the
same one set in PCONSOLE.
3. The network cable or power adapter connected to the print server is loose or
disconnected.
4. The printer is off-line, jammed or out of paper.
Solutions
1.
2.
3.
4.
Check all the information in PCONSOLE.
Check all the information of the print server by running PSAdmin.
Check to see that if the network cabling and power adapter are properly connected.
Recheck the print server connection by running the PSAdmin. It should read
“Connected.”
Question B
Print jobs start printing, but print very slowly or print unknown characters.
Possible explanation and solution
A printer driver is missing or is incompatible with that printer. Using a print driver that is not
specific for the printer can cause printing errors. Install the proper printer driver. If these
printer drivers are not available to you, please contact your printer manufacturer.
Question C
The upgrading process indication bar stops and does not seem to proceed again while
upgrading the print server.
Possible Explanation
There might be a network problem. This causes the upgrading procedure to fail.
Solutions
1.Check the network cabling, especially from the workstation running the PSAdmin to the
print server unit.
2.Run the PSAdmin and upgrade the print server again.
77
V0.2.32 Draft version, for evaluation sample only.
Question D
The Status LED light keeps blinking after POST.
Possible explanation and solution
The last upgrade process was not completed. The print server must be upgraded again by
using the PSAdmin. Please see Chapter 3 for details.
Question E
The PSAdmin reports “Create Print server Error”, “Create Printer Error”, or “Create Print
Queue Error” while using Auto Setup.
Possible Explanation
The print server name, the printer name, or the print queue name you specified in the Auto
Setup dialogue box contains a space.
Solution
Check to see if there is a space in the print server name, the printer name, or the queue
name. Type in a new name without a space between two characters or replace a space by a
dash (-) or an underscore (_).
Question F
The PSAdmin reports “Print server Already Exists”, “Printer Already Exists”, or “Print Queue
Already Exists” after specifying the print server name, or the print queue name in Auto Setup.
Possible Explanation
A same print server name or queue names exists in the specific NetWare file server as the
one you specified in the Auto Setup dialogue box.
Solution
Specify a new print server name or queue name in the Auto Setup.
Question G
The setup Wizard can’t find print server.
Possible Explanation
The Personal Firewall installed in your computer blocks the connection.
Solution
Please disable the Personal Firewall or adjust the security level to lower.
78
V0.1.32 Draft version, for evaluation sample only
Additional Installation Instructions
Panasonic KX-P6100/6300/6500
If you are using a Panasonic KX-P6100/6300/6500 laser printer with the print server through
the Network Print Port under Windows 95/98, please redirect the printer named
“Panasonic KX-P6100 PCL” or “Panasonic KX-P6300 PCL”, or “Panasonic KX-P6500
PCL” to the print server through the Network Print Port.
DO NOT redirect the printer named “Panasonic KX-P6100 GDI”, “Panasonic KX-P6300
GDI”, or “Panasonic KX-P6500 GDI” to the print server.
Please note that the print server doesn’t support printing with host-based printers,
e.g. CAPT, GDI, and PPA printers. Furthermore, the print server doesn’t support any
non-printing functions of MFP (Multiple Function Printer).
79

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2005:03:30 06:20:08Z
Modify Date                     : 2005:03:30 14:32:21+08:00
Page Count                      : 48
Creation Date                   : 2005:03:30 06:20:08Z
Mod Date                        : 2005:03:30 14:32:21+08:00
Producer                        : Acrobat Distiller 5.0.5 (Windows)
Author                          : Weng
Metadata Date                   : 2005:03:30 14:32:21+08:00
Creator                         : Weng
Title                           : 615WU English Manual V0.pdf
Has XFA                         : No

EXIF Metadata provided by EXIF.tools