Zhejiang Dahua Vision Technology DH-IPC-AX6 CONSUMER CAMERA User Manual x
Zhejiang Dahua Vision Technology Co., Ltd CONSUMER CAMERA x
Users Manual
Dahua A Series HD Wi-Fi Network Camera
Quick Start Guide
V 1.0.3
Dahua Vision Technology CO., LTD
1
1
11
1 Packing List
Packing List Packing List
Packing List
Device × 1 QSG ×1
Power Adapter ×1 Screw Package ×1
Quick Installation Board ×1 Installation Position Map×1
2
USB ×1
3
2
22
2 Product Appearance
Product Appearance Product Appearance
Product Appearance
Figure 2-1 Figure 2-2
Figure 2-3
Please refer to the following sheet for more details about each port.
Sheet 2-1
SN Name
1 Lens
2 Microphone
3 Reset/WPS (Wi-Fi Protected Setup)button
4 Micro SD card slot
5 Ethernet port
6 Power port
7 Indicator light
8 Speaker
4
Note:
For reset, long press for 8 seconds and then the light off; For WPS (Wi-Fi Protected Setup), one quick
press.
Please refer to the following sheet for more details about status of indicator light.
Device status Indicate light status
Red light spinning Booting, device malfunction, fail to boot up
Green light spinning Booting completed, await Wi-Fi config,
enter smart config status;
Green light flashing
Wi-Fi smart config in progress, including
WPS (Wi-Fi Protected Setup),
management frame, etc.
Blue light stably on Wi-Fi connection succeeded, operate
normally.
Blue light flashing Device upgrade
Yellow light flashing Network disconnection
Red light flashing Alarm or SD card does not work
Sheet 2-2
5
3
33
3 Operate by Easy4ip APP
Operate by Easy4ip APPOperate by Easy4ip APP
Operate by Easy4ip APP
Step 1
Power on the device with power adapter.
Step 2
Connect your smart phone to your Wi-Fi network. Scan the “Easy4ip” QR on the packing box,
download and install the Easy4ip APP.
Step 3
Open Easy4ip APP (take IOS as an example), tap “Login” to login the APP, see Figure 3-1. Please
register an account for your first use.
Figure 3-1
Step 4
Please tap “+” to add new devices after you log in your account.
6
Figure 3-2
Step 5
Scan the QR code on the back of the camera to get the SN, you can also tap “Continue without
scanning” and manually input the SN number on the next page.
7
Figure 3-3
Step 6
Fill in the Username and Password of the new camera, both of which are admin by default.
8
Figure 3-4
Step 7
Select “Yes, config Wi-Fi”, and fill in your Wi-Fi password, then tap “Next”. During the Wi-Fi connecting
process, please put your smartphone and the camera within 30cm.
9
Figure 3-5 Figure 3-6
Step 8
Your Camera will be added to your account.
10
Figure 3-7
Note:
If you have more cameras, please follow steps 4-8 to add them one by one.
If you want to change the Wi-Fi signal, please reset the camera to factory default and repeat steps
4-8 to add the device.
11
4
44
4 Device Installation
Device Installation Device Installation
Device Installation
Important
Before the installation, please make sure the installation environments can at least support 3x weight
of the camera.
Figure 4-1
Note:
This quick start guide is for reference only. Slight difference may be found in user interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective
owners.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more information.
12
5
55
5
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
product generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment should be installed and operated with a minimum distance 20cm between
the radiator and your body
Dahua Vision Technology Co., Ltd
Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: +86-571-87688883
Fax: +86-571-87688815
Email:overseas@dahuatech.com
Website: www.dahuasecurity.com