Zhejiang Libiao Robotics LBAP-102LU-900 Wireless Communication Device User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3948652
Application ID	NjEX8bQ+KkYxR1zz6egRwg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	37.36kB (467044 bits)
Date Submitted	2018-08-02 00:00:00
Date Available	2018-08-02 00:00:00
Creation Date	2018-07-31 10:47:08
Producing Software	福昕PDF生成器版本8.3.0.0331
Document Lastmod	2018-07-31 10:47:08
Document Title	User Manual
Document Creator	福昕软件开发股份有限公司
Document Author:	Administrator

ZheJiang Libiao Robotics Co.,Ltd.
LBAP-102LU-900 Wireless Communication
Device
Instruction Manual
V1.0
2018.7
Note: The picture of this manual is for reference only.
FCC Warning
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
Catalogo
1. Product Introduction .……………………………………..1
1.1 Product series…………………………………………………………………..………….....1
1.2 Product Usage…………………………………………………………………………….… 1
1.3 Product Features
……………………………………………………………………...……1
1.4 Electrical Specification…………………………………………………….……………….. 1
1.5 Electrical Parameter…………………………………………………………………..……...2
2. Product Structure and Composition……………………..2
2.1 Product Appearance Structure and Size …………………………………………………..….3
2.2 Panel Wiring Instructions
……………………………………………………………..….3
3. Product Usage Setting Instructions……………………....4
3.1 Reset……………………………………………………………………………..…………..4
3.2 Wired communication interface Instructions…………………………………..…………….5
3.3 Antenna Connection
……………………………………………………...………………5
3.4 Device IP Settings instructions……...……………………………………………...…………5
4. Minimum System Topology……………………...………..7
Wireless Communication Device
Instruction Manual
1、Product Introduction
1.1 Product model description
LBAP-102LU-900: Corresponding to 902-928MHz
1.2 Product Usage
Wireless communication device is mainly used in automatic sorting system
robot of our company, which is used for wireless communication between
server equipment and robots, replacing the WIFI communication method of
traditional robot.
The wireless communication device has an Ethernet interface supporting POE
power supply and a USB interface inside , and the server can communicate with
the device through a network or a USB interface, and then communicate with
the client-side by wirelessly.
1.3 Product Features
Support POE power supply mode, convenient on-site wiring;
Compatible with USB interface;
Wireless communication distance is far;
Adopt dual module wireless communication module；
The product is stable and reliable.
1.4 Electrical Specification
1.4.1 working power supply
POE: 44 ~ 57V / 150mA；
USB:5V / 500mA；
1.4.2 Environmental requirements
a. Environmental pressure: 86 kPa～106 kPa
b. Environment temperature: -40℃～+85℃
c.Air relative humidity: 10% ～90%, relative humidity, no condensation
(at＋25℃）；
d.Environment without significant shaking or violent shock vibration
1.5 Electrical Parameter
Modulation
GFSK
Frequency Range
904.25-926.25MHz
Antenna Type
External Antenna
Antenna Gain
5.0dBi
Lowest Internal Frequency of EUT
8MHZ
MAX. Field Strength
Antenna 0:102.63dBuV/m
Antenna 1:101.62dBuV/m
2、Product Structure and Composition
2.1 Product Appearance Structure and Size
As shown below ，The picture 1 shows a wireless communication device，
the size is 123mmx104.5mmx28.3mm.
Picture 1 Appearance structure of wireless communication device
2.2
Panel Wiring Instructions
Piture 2 Panel Wiring Instructions
As shown in the picture 2, the panel is shown as follows:
1. Thernet interface with POE power supply.
2. USB interface, connect to the computer.
3. LED indicating lamp
R1
The light is on, indicating that the wireless module 1 has
received the data.
R2
The light is on, indicating that the wireless module 2 has
received the data.
M1
The light is on, indicating that the network port receives the
data.
M2
The light is on, indicating that the USB receives the data.
4. Reset botton (restore factory settings)
3、Product Usage Setting Instructions
3.1 Reset
As shown in picture 2, press the button to keep the four lights R1, R2, M1, M2
all on and then release, the device IP will be restored to the factory settings, the
factory setting IP address is: 192.168.0.200;
3.2 Wired communication interface Instructions
Wireless communication devices can communicate using Ethernet or USB
interfaces,which can only be communicated in one way at a time.
Support standard POE mode power supply when communicating with Ethernet
interface.
Power is supplied directly from the USB when communicating with USB
interface.
3.3 Antenna Connection
The wireless communication device has two built-in wireless modules, which
can be configured with two external antennas,when the first module fails to
communicate, it automatically switches to the second 0ne for communication to
enhance the communication success rate and reduce the blind area of
communication.
3.4 Device IP Settings instructions
Open the software APLoopback Test, as shown in the picture 3:
Picture 3
First ,change the IP address as shown in the picture 4 to the current IP address
of the wireless communication device, for example, 192.168.0.200.
Picture 4
Enter the IP address you want to set as shown in the picture 5, for example,
192.168.1.100 , and then click to set , the display is successful, it’s successful ,
if it fails, it shows no response .
Pictur 5
You can use this software to test whether the IP address has been set
successfully .Input the IP address you set into the picture box, and click to test.
As shown in the picture 6.
Piccture 6
If the display is successful, the setting is successful , if the display fails, the
setting fails , if the display times out, it indicates that the communication is bad,
as shown in the picture 7.
Picture 7
4、Minimum System Topology
Picture 8 Minimum system TOP diagram
As shown in the picture 8,
the minimal system topology for Ethernet
connections.
The server is connected to the wireless communication device through the POE
switch, and the POE switch provides power support for the device while
communicating with the wireless communication device.When the server needs
to interact with the robot, the server communicates with the wireless network
device through UDP, then the wireless network device transmits data through
the wireless module and the wireless module on the robot, and then sends the
data back to the server through the wired link for a link communication.
When it is necessary to expand device and increase wireless communication
channels, it only needs to add wireless communication device.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Page Count                      : 10
Language                        : zh-CN
Tagged PDF                      : Yes
Creator                         : Administrator
Title                           : 
Description                     : 
Subject                         : 
Creator Tool                    : 福昕软件开发股份有限公司
Producer                        : 福昕PDF生成器版本8.3.0.0331
Keywords                        : 
Company                         : China
Create Date                     : 2018:07:31 10:47:08+08:00
Modify Date                     : 2018:07:31 10:47:08+08:00
Author                          : Administrator

EXIF Metadata provided by EXIF.tools