Zhongshan K mate General Electronics BTT023 Bluetooth audio transmitter User Manual BTT023 User s manual

Zhongshan K-mate General Electronics Co., Ltd Bluetooth audio transmitter BTT023 User s manual

UserManual.wiki >

Zhongshan K mate General Electronics >

BTT023 User Manual

Manual.pdf

BTT023 Bluetooth stereo transmitter

Content  Before use………………………………………………….….1 1. About BTT023……………………………………………..….1 2. System requirements………………………………………..…1 3. Overview…………………………………….………………...2  Getting started………………………….......……………….….2 1. Charging…………………………….....….…………………....2 2. Turning on/off the transmitter……………………...……….…3 3. Pairing with Bluetooth devices………………………….…….3 4. Reconnecting with device...........................................................4 5. LED indicator………………………………….……….……..5  Care and maintenance………………………………………….5  FAQs…………………………………………………..………6  Specifications…………………………………..…………..…6

3. Overview  Getting started 1. Charging First using—You must charge the battery fully before first using. Low power—It means low power if the red LED of the transmitter flashes during using. At this time, you need to recharge the transmitter. The charging steps as follows: Step1: Connect the USB charging cable into the USB port of PC or charger; Step2: Connect the other end of USB charging cable to charging port of the transmitter. 2 1 Multi-function button 2 LED indicator 3 3.5mm audio plug 4 Charging port DC 5V

The pairing steps as follows: 1) Make sure the transmitter is turned off, otherwise please turn it off first; 2) Keep the transmitter and your Bluetooth stereo receiver within 1 meters; 3) Turn on your Bluetooth receiver and make it enter into pairing mode; 4) Press the MFB button of transmitter about 4~5 seconds and release it until red and blue LED flash alternately. The transmitter has already enter pairing mode; 5) The transmitter will search, paired and connect with Bluetooth receiver automatically; 6) After connecting successfully, blue LED of the transmitter flashing three times every 4 seconds; 7) Connect the transmitter to your music player through 3.5mm audio jack to play music. Remark:  The transmitter can remember 8 paired devices, when the paired devices over 8, the first paired device will be replaced.  The transmitter can pair with stereo Bluetooth receiver which PIN Nos. is:0000”,”1234”or ”1111”,”8888”. 4. Reconnecting with device 1) Automatic connecting Every time the transmitter is turned on, it will connect to last connected device automatically. Besides, it also will connect with the device in paired list in turn until it connect with a device successfully. 2) Manual connecting When the transmitter in standby mode and not connect with a device, short press MFB button once, it will connect to last connected device. 3) Can be connected When the transmitter in standby mode and not connect with a device, it can accept the connect request from the paired receiver. 4

5. LED indicator LED indicator Status of the transmitter Red and blue LEDs flash alternately Pairing mode Blue LED flashes three times every 4 seconds Already connected with Bluetooth device Blue LED flashes once every 2 seconds Not connected with Bluetooth device Red LED on Charging Red LED off Finish charging  Care and maintenance Before using the BTT023, please read the following recommendations, it will help you to enjoy the product for many years.  Keep dry and don’t put it in the wet place, in case of affecting the interior circuit of product.  Don’t put the product under the sunlight or place in hot areas. High temperature will shorten the life of electronic device and distort certain plastic.  Don’t expose the product to extreme temperatures, it may damage the internal circuit board.  Don’t try to take apart the product, it may damage the product if you are not professional.  Don’t fall off on the floor or knock the hard substance, it may damage interior circuit.  Don’t uses intensify chemical or detergent to clean the product.  Don’t scrap the surface with sharp things. If the product can’t work normally, please send it to the regularly asserted store, the staff will help you to solve the problem warmly. 5

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.