Zhongshan K mate General Electronics BTT025A Bluetooth Audio Transmitter User Manual BTR006

Zhongshan K-mate General Electronics Co., Ltd Bluetooth Audio Transmitter BTR006

UserManual.wiki >

Zhongshan K mate General Electronics >

BTT025A User Manual

Users Manual

BTT025A Bluetooth audio transmitter User’s manual

Content  Before use…………………………………………………...…1 1. About BTT025A………………………………………...…….1 2. System requirements………………………………...…………1 3. Overview of BTT025A…………….…………………...……...1  Getting started…………………….……………………………2 1. Charging the transmitter…………......………………………....2 2. Reeling the cable ....................…..…………………………...2 3. Turning on/off the transmitter.....................................................3 4. Pairing with Bluetooth devices...................................................4 5. Playing music …………..…………………………………….5 6. LED indicator…………..……………………………………...5 7. Factory reset................................................................................5  Care and maintenance………….………………………………6  FAQs…………………………………..……………………….7  Specifications……………………...…………………………...7  FCC Statement…………………………………..…………….7

 Getting started 1. Charging the transmitter First using—You must charge the battery fully before first using. Low power—It means low power if the red LED of the transmitter flashes during using. At this time, you need to recharge the transmitter. The charging steps as follows: 1) Connect the USB charging cable into the USB port of PC or charger; 2) Connect the other end of USB charging cable to charging port of the transmitter. RED light on→Charging RED light off→Finished charging 3) It will take about 2 hours to finish charging. Warning: The battery is recyclable. Batteries (battery pack or batteries installed) shall not be exposed to excessive heat place, such as sunshine, fire or the like. 2 Reeling the cable 1) Please reel the audio line into the cable slot if you don’t use the product. It is convenient to carry and store. Please operate it as shown below . 2

2) Taking the audio line out from the cable slot as shown below if you want to use the product. Remarks:  Please don’t push the 3.5 mm plug into the buckle directly when you reel the audio line.  Please don’t pull the3.5mm plug out from the buckle directly when you take out the audio line.  The audio line should be push in or pull out by sliding as above shown to avoid the damage of the buckle. 3.Turning on/off the transmitter Function Operation LED indicator Turning on Ensure the transmitter is off, press and hold MFB button for 3seconds Blue LED on for 1 second Turning off Ensure the transmitter is on, press and hold MFB button for 3seconds Red LED on for 1 second Enter pairing mode Ensure the transmitter is off, press and hold MFB button for 5 seconds. Blue and red LED flash alternately 3

5. Playing music 1) After successful connecting of BTT025A with Bluetooth receiver device , you can play your music on your Bluetooth receiver device. 2) BTT025A not only support SBC mode , but also support APTX and APTX low latency mode. But all this need your Bluetooth receiver device also support these modes. 6. LED indicator LED indicator Status of BTT025A Red and blue LED flashes alternately Pairing mode Blue LED flashes once every 4 seconds Connected with device(SBC mode) Blue LED flashes twice every 4 seconds Connected with device(APTX mode) Blue LED flashes thrice every 4 seconds Connected with device(APTX low lattency mode) Blue LED flashes once every 2 seconds Not connected with device Red LED on Charging 7. Factory reset In the status of standby or off mode, long press MFB button for about 10 seconds and release it until the red and blue LED on simultaneously. 5

Remarks:  After factory reset, the paired list of transmitter will be deleted. When you turn on the transmitter again, it will enter pairing mode automatically, but it won’t connect to device automatically, you should re-pair and connect to devices.  In the status of off mode, reset the BTT025A ,it will enter the process of turn on, pairing, factory reset, enter pairing. The LED indictor will change from blue LED on , red and blue LED on simultaneously, to blue LED and red LED flashes alternately, and then enter pairing mode directly.  In the status of standby mode, reset the BTT025A , it will enter the process of turn off, factory reset , turn off. The LED indictor will change from red LED on , red and blue LED on simultaneously, to LED indictor off, and then turn off.  Care and maintenance Read the following recommendations carefully before using BTT025A. Following these you will be able to enjoy this product for many years.  Keep it dry and don’t put it in the dump place to avoid the product’s internal circuit being affected.  Keep the product away from direct sunlight or hot places. High temperatures will shorten the life of electronic devices, destroy the battery or distort certain plastic part.  Don’t expose the product to cold areas. It may damage the internal circuit board.  Don’t try to disassemble the product as it may get damaged if you are not professional.  Don’t let it fall down onto the floor or other hard surfaces. The internal circuit might get damaged.  Don’t use intensive chemical products or detergent to clean the product.  Don’t scratch the surface with sharp things. It may get damaged by sweat. In case the transmitter doesn’t function properly, please send it to the store that you bought it. The staff will help you to solve the problem. 6

 FAQs 1. What to do when BTT025A can’t be turned on? Please charge the BTT025A. 2. What to do when BTT025A can’t pair and connect to a Bluetooth device? a)Make sure Bluetooth receiver supports A2DP; b)Make sure Bluetooth receiver is placed within 1 meters; c)Make sure Bluetooth receiver has already entered into pairing mode. 3. What to do when I can’t listen to music from Bluetooth receiver？ a)Make sure the transmitter connect well with player; b)Make sure player is playing music.  Specifications Bluetooth version Bluetooth V2.1+EDR Bluetooth profiles A2DP Bluetooth frequency range 2402MHz-2480MHz Operating distance About 10 meters Charging input voltage DC 5V Working time About 12 hours Charging time About 2 hours Dimension 52*23*10 mm  FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 7

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.  FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 8