Zinwell ZWX-B290 802.11b USB WLAN Pen Adapter User Manual UserManual EN v1 02
Zinwell Corporation 802.11b USB WLAN Pen Adapter UserManual EN v1 02
Zinwell >
Installation Guide
Wireless LAN Device Series
WLAN USB Pen-Type Adapter
ZPlus-B290 User’s Manual
Version. 1.02 (10.07.2003)
1
Notice
“ This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
The users manual or instruction manual for an intentional or unintentional radiator shall caution
the user that changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed.
Consult the dealer or an experienced radio/TV technician for help.
The Product name has been tested to the FCC exposure requirements (Specific Absorption Rate).
CAUTION:
1. The equipment complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2).
2. This Transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
2
Contents
1 Introduction....................................................................................... 3
1.1 Package Contents ........................................................................................................ 3
1.2 System Requirements.................................................................................................. 3
2 Quick Installation..............................................................................4
3 Installation Procedures Under MS Windows.................................. 5
3.1 Installing the Application and Drivers under Windows 98SE/Me /2000/XP......... 5
3.2 Uninstall the Driver/Application..............................................................................12
4 Configuration & Monitor Utility .....................................................15
4.1 Quick step-by-step start to connect site................................................................... 15
4.2 System tray................................................................................................................. 18
4.3 Main dialog box of Utility.........................................................................................18
4.4 More Setting…........................................................................................................... 19
4.5 General connection setting ....................................................................................... 20
4.6 Encryption.................................................................................................................. 21
4.7 Language .................................................................................................................... 22
4.8 Profile .........................................................................................................................22
4.9 Other...........................................................................................................................23
3
1
1
I
In
nt
tr
ro
od
du
uc
ct
ti
io
on
n
This USB device is a Wireless LAN Adapter with a rate of 1, 2, 5.5, and 11 Mbps operating
in the ISM band using Direct Sequence Spread Spectrum (DSSS) transmission,
conforming the IEEE 802.11b standard. For these card currently provides Device Drivers
for Microsoft Windows® 98SE/Me/2000/XP.
1.1 Package Contents
Before you do anything, open your package and verify it includes:
ZPlus-B290 Adapter
USB Cable
Setup Utility CD containing User’s Manual
Quick Start Guide
1.2 System Requirements
Operating System: MS Windows 98SE/Me/2000/XP.
Desktop/notebook PC with CD-ROM drive and USB interface.
4
2
2
Q
Qu
ui
ic
ck
k
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
This section provides a quick step by step guide on how to install your Wireless LAN USB
Adapter. Please follow the steps described below and refer to the appropriate sections for
further details:
Power on the computer.
Please make sure that
you don’t insert your WLAN USB adapter yet.
Install the drivers and application:
1. Insert the given Installation CD into your CD-ROM drive.
2. Click “Install/Uninstall software” button to install.
3. Follow the installation instructions from the InstallShield Wizard by pressing the
“Next” button.
4. Choose the appropriate of installation, according to your needs (Application,
Drivers)
5. If you want to set the path of your choice, select “Browse” and then “Next”.
6. Then setup wizard will help you finalize the rest steps.
7. Push the “OK” button, and then reboot system.
8. The installation will be completed after reboot.
Insert your WLAN USB adapter.
The “Add New Hardware Wizard” automatically loads the Drivers.
Refer to sections 3 for more details on the installation and configuration under
Windows 98SE/Me/2000/XP respectively. Section 4 gives detailed instructions on
how to use the Configuration Utility.
ZPlus-B290 802.11b WLAN USB Adapter
ZPlus-B290 Wireless LAN USB Adapter
Install/ Uninstall Software
User’s Manual
Explore CD-ROM
Browser Our Web Site
Exit
Copyright(C) 2003 ZINWELL V1.00
ZPlus-B290 802.11b WLAN USB Adapter
5
3
3
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
P
Pr
ro
oc
ce
ed
du
ur
re
es
s
U
Un
nd
de
er
r
M
MS
S
W
Wi
in
nd
do
ow
ws
s
The procedures described in this section to install and configure the Wireless LAN USB
Adapter under MS Windows 98SE/Me/2000/XP.
3.1 Installing the Application and Drivers under Windows 98SE/Me
/2000/XP
Please do not plug your USB adapter until the Application setup has been
completed. The setup procedure described below installs both the drivers
and the Configuration & Monitor Utility.
1. Insert the Driver CD to your CD-ROM, the following window will pop up and Click
“Install/Uninstall software” button to install. (If the following window doesn’t pop up,
click the Start button at the Taskbar and then select Run. Enter E:\autorun.exe if E
is your CD-drive.)
ZPlus-B290 Wireless LAN USB Adapter
Install/ Uninstall Software
User’s Manual
Explore CD-ROM
Browser Our Web Site
Exit
Copyright(C) 2003 ZINWELL V1.00
6
2. Follow the installation instructions from the InstallShield Wizard by pressing the
“Next” button.
3. The installer will install the needed files to a folder named “C:\Program Files\Wireless
LAN Series\ZPlus-B290”. If you want to change this, Click”Browse” and select a
folder. Click “Next” to continue.
Setup will install ZPlus-B290 802.11b WLAN USB Adapter in the following folder.
To install to this folder, click Next. To install to a different folder, click Browse and
select another folder.
C:\…\Wireless LAN Series\ZPlus-B290\
7
4. Choose all program features will be installed. If you want to change this, Click
“Custom”, Choose which program features you want installed. Click
“Next”
to
continue.
5. The installer will create a program folder called ZPlus-B290 802.11b WLAN USB
Adapter. If you want to change this, enter a name or select from the list below.
Click
“Next”
to continue.
C:\…\Wireless LAN Series\ZPlus-B290
C:\…\Wireless LAN Series\ZPlus-B290
l
us-B210M 802.11b WLAN USB Adapter
ZPlus-B290 802.11b WLAN USB Adapter
8
6. Start Setup.
7. Click
“OK”
to complete the installation and restart the computer.
8. After the computer restarts, plug WLAN USB Adapter connector into USB port on
computer.
9
Under MS XP-
9. After the computer restarts, plug WLAN USB Adapter connector into USB port on
computer then Windows XP detects the device automatically, briefly showing a
message “Found New Hardware” and starts collecting information for a device
information database.
10. When Windows XP is ready to configure the new hardware, it opens the Found
New Hardware Wizard dialog box as shown; a dialog box appears asking what you
want the wizard to do. Select “Install the software automatically
(Recommended)” and Click “Next”.
ZPlus-B290 802.11b WLAN USB Adapter
10
11. Starting search the driver automatically.
12. Starting install driver automatically, Click
“Continue Anyway”
ZPlus-B290 802.11b WLAN USB Adapter
11
13. Hardware installation finished, Click “
Finish”
.
14. You will find an icon in indicated “Wireless LAN USB Adapter” on your system tray.
You can double-click on it to configuration.
ZPlus-B290 802.11b WLAN USB Adapter
12
3.2 Uninstall the Driver/Application
There are three way to uninstall the driver/application.
1. Uninstall from windows “Control Panel”
2. Uninstall from “Installation CD”
3. Uninstall from windows “Start Menu”
Note:
It is recommended to “Exit” the “Configuration & Monitor Utility”, when
you uninstall. No matter what way you choose to uninstall.
Uninstall form windows “Control Panel”
Under MS Windows 2000/XP
1. Open
“Control Panel”
.
2. Double click
“Add or Remove Programs”
.
13
3. Choice the
“Change or Remove Programs”
.
4. Select the “ZPlus-B290 802.11b WLAN USB Adapter” from the list.
5. Click the
“Change/Remove”
button.
6. Click the
“Next”
button, and then click “
OK
”.
ZPlus-B290 802.11b WLAN USB Adapter
14
Uninstall from Installation CD
Insert the Installation CD to your CD-ROM, the following window will pop up and Click
“Install/Uninstall software”
button to uninstall.
Uninstall from Windows Start Menu
Select “Start->All Program->Wireless LAN Series->ZPlus-B290“, Choose
“Uninstall”.
ZPlus-B290 Wireless LAN USB Adapter
Install/ Uninstall Software
User’s Manual
Explore CD-ROM
Browser Our Web Site
Exit
Copyright(C) 2003 ZINWELL V1.00
15
4
4
C
Co
on
nf
fi
ig
gu
ur
ra
at
ti
io
on
n
&
&
M
Mo
on
ni
it
to
or
r
U
Ut
ti
il
li
it
ty
y
The “Configuration & Monitor Utility” is a powerful application that helps you to
configure the Wireless LAN Adapter and monitor the statistics of the communication.
Unlike the standard method of configuring the card via the operating system utilities (e.g.
Control Panel), this application permits the dynamic modification of the configuration
parameters while the adapter is operating. It also offers some more configuration options.
Offers the “Configuration & Monitor Utility” for Windows 98/Me/2000/XP.
Note
：
Please keep in mind that the Configuration & Monitor Utility can be used to
change the above configuration parameters when the cards are active.
When the cards are not in use, please use the Control Panel method.
4.1 Quick step-by-step start to connect site
Double-click the icon on the system tray to open “Configuration & Monitor utility”.
Click “Refresh” button to scan nearby available network.
Select one of available network and click “Connect this site” button to connect site.
ZPlus-B290 802.11b WLAN USB Adapter
Wireless LAN USB Adapter Utility
16
If adapter connect successfully, you can get the information about link status,
signal strength and link quality.
Note
：
Under Windows XP, Operating system will use ”Windows Zero
Configuration” to set your adapter. If you want to use our “Configuration
& Monitor utility”, you need to disable “Windows Zero Configuration”, first.
(See next section: How to disable “Windows Zero Configuration”.)
Or when you open “Configuration & Monitor utility” by double-clicking on icon
of system tray, it will pop up the error message” Wireless LAN is
controlled by Windows Zero Configuration!!! ”.
17
How to Disable “Windows Zero Configuration”.
Step 1. Right click the Wireless Network Connection icon in notification area and
select "View Available Wireless Network”.
Step 2. Click "Advanced..." button.
Step 3. Disable "Use Windows to configure my wireless network settings" and
click "OK".
18
4.2 System tray
The “Configuration & Monitor Utility” appears as an icon on the system tray of
Windows, when the adapter is running. And it will change image with signal strength. You
can open utility by double-clicking on this icon.
0% 0~20% 20~40% 40~60% 60~80% 80~100%0% 0~20% 20~40% 40~60% 60~80% 80~100%
4.3 Main dialog box of Utility
You can survey the reachable assess points and the wireless LAN adapter. And get the
information about the status of the communication (the SSID of the access point to which
the adapter is associated, signal strength, and link quality).
ZPlus-B290 802.11b WLAN USB Adapter
Wireless LAN USB Adapter Utility
19
4.4 More Setting…
Click “More Setting…” button, this dialog box consists four items can help you to
monitor and configure the Wireless LAN Adapter, the five items are “General
connection setting”, “Encryption”, “Language”, “Profile” and “Other”.
• General connection setting – About channel, TxRate, Network type and SSID.
• Encryption – About Authentication mode and WEP Key setting.
• Language – About language setting.
• Profile – About profile manage.
• Other – About Power saving mode, Fragmentation RTS/CTS Threshold and system
information.
20
4.5 General connection setting
In order to change the configuration parameters click the “Change” button (See
Figure 4.5.1), make your changes and then click “Apply” to save the changes (See
Figure 4.5.2).
Figure 4.5.1
Figure 4.5.2
Network Type: The 802.11 standard supports two network topologies: Ad Hoc and
Infrastructure mode.
Infrastructure – This mode of operation requires the presence of an 802.11b
Access Point. All communication is done via the Access Point, which relays
packets to other wireless Clients in the BSS as well as to modes on a wired
network such as Ethernet.
Ad Hoc – This is the 802.11b peer-to-peer mode of operation. All
communication is done from Client to Client without the use of an Access Point.
802.11 Ad Hoc networking uses the same SSID for establishing the wireless
connection.
SSID: SSID is the group name that will be shared by every member of your wireless
network. You will only be able to connect with an Access Point, which has the same
SSID.
Channel: There are 14 channels available. The channels differ from country to
country. Select the channel to be used.
TxRate: By default the unit adaptively selects the highest possible rate for
transmission. Select the basic rates to be used among the following options 1, 2, 5.5,
11 (Mbps).
21
4.6 Encryption
You can set four different WEP keys and specify which one of them to use. First,
either enable or disable encryption from the appropriate “Enable WEP” (see Figure
4.6.1). If you decide to use encryption, you can click "WEP More..." button to choose
any of the available WEP keys (1 to 4). You also have the option to select the WEP
Length. Please keep in mind that the WEP keys must be in HEX format. Finally, you
have the option to select whether Open System, Shared Key, or Auto authentication
will be used. In order to take effect the changes you wish to make, press the
“Change” button at the bottom of the dialog box (see Figure 4.6.2).
Figure 4.6.1
Figure 4.6.2
22
4.7 Language
You can choose one of the below language list, then click “Apply” button.
4.8 Profile
Profile is a named set of operating parameters for your Wireless LAN USB adapter.
The “Load Profiles setting” let you set values for all parameters by selecting a
previously defined profile. The Existing profiles display the available profiles for your
USB Wireless LAN adapter. When you change the configuration parameters, press
the “Save profile setting” button to save your changes. And you also can click
“Load default setting” to load factory default value or click “Delete profile setting”
button to delete settings (See Figure 4.7.1).
Figure 4.7.1
23
4.9 Other
Advanced
By Choosing the Advanced option, you can change advanced configuration settings,
such as the Preamble Type, Fragmentation Threshold, and RTS/CTS Threshold.
Figure 4.8.1 shows the default configuration for the advanced settings. Before
selecting Short Preamble, make sure that the other stations and Access Points are
also supporting this feature. When selecting “Auto” for the Preamble Type it
automatically selects the Preamble Type depending on the Access Point Preamble
Type.
Figure 4.8.1
24
Information
About driver, firmware and utility version..... (See Figure 4.8.2)
Figure 4.8.2