KL003_76011 KL003 76011

: Zip Water Kl003 76011 KL003_76011 zipwater.installation.layout zipwater.chilled water zipwater.products zipwater.australia

Open the PDF directly: View PDF .
Page Count: 1

Surface finishes unless

otherwise stated:

Sand-Cast = 16.0µm1.

Drilling = 6.3µm2.

Forging = 6.3µm3.

Milling = 3.2µm4.

Turning = 3.2µm5.

Boring = 3.2µm6.

Die-Cast = 1.6µm7.

Reaming = 1.6µm8.

Grinding = 0.8µm9.

Honing = 0.4µm10.

Polishing = 0.2µm11.

Limits unless otherwise stated:

Fabricated 0.751.

Sand-Cast 0.352.

Forging 0.25 3.

Die-Cast 0.254.

Moulded 0.155.

Machined 0.25mm6.

Angular 0.50degree7.

Fits unless otherwise stated:

Free Running = H9/d91.

Running = H8/f82.

Clearance = H7/h63.

Sliding = H7/g64.

Interference = H7/u65.

XXX.XX

Features marked with this symbol:

must be referred to in the manufacturing control plan

THIRD ANGLE

PROJECTION

R

Isometric View (1:1)

Configuration : Default

635

1670

921

DETAIL FRONT VIEW

SCALE 1 : 7.5

Carafe Filler

Bubbler

Floor level

270

413

DETAIL SIDE VIEW

SCALE 1 : 7.5

Plinth

Wall

560.9

306

256

DETAIL TOP VIEW

SCALE 1 : 7.5

DETAIL REAR VIEW

SCALE 1 : 7.5

PVC Drain Fitting

Filter

Chiller Unit

Valve

REVISIONS

Rev

XXXX

YYYY

Last Change(s)

ECO

Date

Init

150

50

200

250

150

100

50

250

200

50

100

250

200

100

150

Web : www.zipindustries.com

Email : sales@zipindustries.com

100

300

400 400

300

350 350

550

450

500

400

350

300

150

200

250

300

350

Dimensions in

millimetres

Drawing to

BS8888:2004

Screw threads to

BS 8498:2008

File Ref : R:\!Released\KL003_76011 (Sheet1)

Sheet1 (Default)

Zip Industries Pty Ltd

67 Allingham Street

Condell Park

Sydney

NSW 2200

Australia

No

Handed? :

Unchecked on 1/01/2001

edgarg on 7/06/2012 9:46:39 AM

Updated by :

EdgarG on 21/05/2012

A

A2

Created by & on

Created by & on

Potable? :

Recyclable? :

No No

Make

See Components

See Components

Comments :

Remove all sharp edges. This drawing ONLY details information

which cannot be ascertained from the 3D geometry of the part(s)

attached. Model & dimensions are AFTER all finishing operations

Raw material :

Manufacturing Route :

Make or Buy :

This drawing is CONFIDENTIAL and is supplied on the express condition that it shall not be LOANED, COPIED or DISCLOSED to

any other third party or used for any purpose without the written consent of Zip Industries Pty Ltd. If this document is printed in

hardcopy form, it is for INFORMATION ONLY and therefore not subject to updating controls.

For the current revision ALWAYS refer to the NATIVE electronic form as stated in the top left-hand corner of this sheet.

© copyright Zip Industries Pty Ltd, 21/05/2012

_Drawing

Property

Part

Property

140 Glass/Hr Filt CMBCF140SFXV

Wallfountain

KL003_76011

377143.7

See Components

Sheet :

1

of

1

1:20

Unapproved on 1/01/2001

EdgarG

on 21/05/2012

New

Manufacturing Instructions

Zip Industries

KL003_76011

Drawing :

Model :

Description :

Status :

Derived from :

Scale :

Approved by :

Checked by :

Finish

Finish :

Material :

Mass

(g)

:

Density

(g/cm3)

:

1.0

Area

(cm2)

:

173345.3

376759.3

Volume

(cm3)

:

Production

Default

Configuration :

Chillmaster/Economaster®

Project :

Size

Rev

Colour

Colour :