Zippy Technology D001L USB Dongle - Receiver User Manual C701324004 rev

Zippy Technology Corp. USB Dongle - Receiver C701324004 rev

User Manual

Windows 98SE Windows ME Windows 2000/NT Windows XP Please do not use this product in ashy, wet, or oily environments. Failure to do so may shorten the life of this product and may cause bodily harm.Please keep this product as far away from Radio Frequency interruption areas as possible.This is not an outdoor product. Exposing this product to the elements may cause damages to the product and bodily harm to its users.Please do not use petroleum, benzene or thinner-based solution to clean this product.Laser MouseInternational standards and safety. This Laser device complies with International Standard IEC 60825-1:2001-08, Class 1 Laser Product, and also complies with 21 CFR1040.10 and 1040.11, except for deviations pursuant to Laser Notice No.50, dated July 26, 2001:1) Emission of a parallel beam of infrared user-invisible light: 2) MaximumPower of 716 microwatts CW, wavelength range 832-865 nanometers; 3) Operating temperature between 0 ( 32 ) to 40 ( 104 ). CAUTION: This Laser device has no serviceable parts. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Safety and Usage Guidelines1) Do not point infrared beam at eye. 2) In the absence of proper operation and if customer-initiated troubleshooting is unsuccessful, switch off device and call technical support. 3) Do not disassemble your product or expose it to liquid, humidity, moisture, or temperatures outside the specified operating range of 0 ( 32 ) to 40 ( 104 ). 4) If you product is exposed to out-of-range temperatures, Switch it off and allow the temperature to return to the normal operating range.B. Setting up the Keyboard and MouseA. Setting up the Dongle Receiver1. Plug the dongle receiver (FIG. 3) into an available USB 2. Wait for Windows to install drivers for the dongle receiver, keyboard and mouse.3. When the dongle receiver has been properly initialized, its LED light will stay alit.Installation ProcedureBefore installing this product please make sure you have one available USB port reserved for the dongle receiver. Dimensions: L105 x W55.5 x H35.5 mm Weight: 80.7 +/- 25g (with Battery) Key Number: 3 Keys (Wheel button on middle button) Battery: 2 x AAA batteries Battery Life: 1 Month (Base on average usage) Channel: 78 Channels ID: Unique ID for mouse Radio Frequency: 2.4 GHz Dimensions: L70xW22.7xH12.3mm Weight : 10.9g +/-25g Interface: USB 1.1Dimensions: 430 x 162x 20 mmWeight: 620+/- 20g (with Battery) Key Number: 104 Keys(By language)Battery: 2 x AAA batteriesBattery Life: 3 Month (Base on average usage)Channel: 78 Channels automatically switch.ID: unique ID for each keyboard Radio Frequency: 2.4 GHzHot Keys : previous page, next page, WWW home, stop, refresh, my favorite, search, e-mail, mute,previous, play/pause, next, stop, volume down, volume up, wake up, sleep, power WarningPlease be careful when resetting the ID's for the keyboard,mouse and dongle receiver. Objects with a sharp point may break and leave behind shards. Battery Low3. We recommend using alkaline batteries for the keyboard. 4.You may need to reset the ID's after replacing new batteries for the keyboard and mouse.User ManualWarning45786213Introduction Wireless Keyboard x 1 Wireless Laser Mouse x 1 USB 2.4GHz dongle receiver x 1 Installation CD x 1 Manual x 1 Alkaline batteries x4 ( 2 AAA for keyboard, 2 AAA for Mouse)Thank you for purchasing our cordless keyboard and Laser mouse. For your own safety, please read this manual thoroughly before using this product. After you have read this manual, please keep it inPlace for reference when necessary.The following items are included in the package. Please make sure all items are accounted for as you open the package. If there was any i tem missing or damaged, please contact the store where the product was purchased or our support center.Contents in the package SpecificationsKeyboardMouseDongle Receiverport.Any malfunction, damage or personal injury caused by the malfunctioning or damage of the user's personal computer or misuse of this product.Do not dismantle, change or modify this product in any way.WarningWAKE SLEEP POWERBatt.Low1. Low-Battery is indicated by the illumination of the keyboard LED indicator "Batt.Low". Please replace the battery when the LED lights up.2. Low-Battery is indicated by the illumination of the Mouse Scroll. Please replace the battery when the LED lights up.ADE-AD2OS supportSystem requirements IBM or compatible PC Windows Operating System Pentium-equivalent processor or above At least 10MB hard disk space One available USB port1. Open the battery compartment covers of the keyboard & mouse(FIG.1) (FIG.2) and insert the batteries. Make sure they are properly installed.2. Replace the battery compartment covers.3. Usually the keyboard and mouse have been set up in the factory. If the system cannot recognize the keyboard and mouse, please follow step 4~7 to bind keyboard and mouse.4. Move the keyboard and mouse close to the receiver (within 30 cm).5. Press the receiver ID button (FIG.3), then press the keyboard ID button (FIG.1).6. Press the receiver ID button again, then press the mouse Reset button (FIG.2).The system will automatically recognize the Mouse.7. The LED indicator on the receiver will turn green when the keyboard and mouse are connected and working properly.This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions(1)•This device may not cause harmful interference and (2)•This device must accept any interference received, including interference that may cause undesired operation You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. 1.•This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the installation. , May cause harmful interference to radio communication. However, there is no guarantee that interferenceWill not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna-Increase the separation between the equipment and receiver-Connect the equipment into an outlet on a circuit different from that to which the receiver is connectedConsult the dealer or an experienced radio / TV technician for help
C701324004Hotkey FunctionsThere are 18 built-in hotkeys for the product for quick access under the Windows operating system. Pleaserefer to the following section on their functions.1112 1413109Function descriptionID button Battery housingFIG.1FIG.2FIG.3Home page Start the WWW browser.E-mail Start the e-mail application.Previous Go back to the previous page of the internet.Next Proceed to the next page of the internet.Search [Search] button of the internet browser.Refresh Reload web page.My favorite [My favorite] button of the internet browser.Stop Stop download of the web page.Volume down Turn down the volume.Volume up Turn up the volume.Mute Toggle the on/off of the sound.Stop Stop the play of the CD.Previous Return to the previous track of the CD.Play/Pause Toggle the play/pause of the CD.Next Proceed to the next track of the CD.SLEEP Suspend Enter the Suspend mode.Wake up: Wake up system when entering suspend mode.POWER Power off or Exit the computer.The CD in the package provide the Number Lock, Scroll Lock, Cap Lock , hotkey information OSD (On Screen Display) function, For Windows 98SE/ 2000/ ME /XP system , the OSD driver should be installed before use, and to use the functions of the hotkeys under Windows 98SE, you must install the software from the CD-ROM. Please follow the ste ps below on bow to install the Multimedia Keyboard software to your system .1.Insert the CD disk ,RF driver , into the CD-ROM drive.2.The system will automatically run the setup.exe once after the disk is inserted, However , if the system . fails to perform the procedure , simply double- click on the setup.exe of CD Disk to continue the installation procedure.3.Follow all the on-screen instructions.How to install the softwareAttentionIf the install screen does not run automatically, open“[My Computer]-->[CD-ROM]-->[Autorun.exe] or [My Computer]-->[CD-ROM]-->[Driver]-->[Hotkey Driver] or [LED OSD Driver]-->setup.exe” .When you restart the computer, onscreen Slim Multimedia will show on the screen, and Slim Multimedia icon will show in the taskbar.You can drag the onscreen Slim Multimedia with the mouse to anywhere you want. To close onscreen Slim Multimedia, right click and left click [Finish] from the menu. When you right click Slim Multimedia icon, the menu will show and you can read the help or version information etc.15On/Off After install keyboard status indication software, you will find 3 small icons in your task bar as follows:When you lock up the Number pad, caps or scroll the light will show green color, otherwise it will show the gray color.Number Lock, Scroll Lock, Caps Lock indication software WAKE SLEEP POWERBatt.LowWAKE SLEEP POWERBatt.LowResetPress button forbattery compartmentUninstall the Hot Key driverClick [Start]-->[Program]-->[RF Status]--> uninstall, and uninstall according to the directions on the screen.Click [Start]-->[Program]-->[wirless]--> uninstall RF keyboard 1.0, and uninstall according to the directions on the screen.Uninstall the OSD driverSelect “Next “ to install OSD driver.Select “Next” Hot key driver installation is only for Windows 98SE users.For Windows98 SE users select “OK” then install the hotkey driver; For Windows 2000/ME/XP users select “Cancel” to not install this dricer.Select “Next” Select “Finish”. This symbol on the product or in the instructions means that your electrical and electronic equipment should be disposed at the end of its life separately from your household waste. There are separate collection systems for recycling in the EU.For more information, please contact the local authority or your retailer where you purchased the product.ID buttonID button on the keyboard (FIG. 1), receiver (FIG. 3), and the reset button on the mouse (FIG. 2) have the same function. If the RF device doesn't work properly, please press any keys after pressing ID button (FIG. 1) (FIG. 3) or reset button (FIG. 2) to connect the RF device.

Navigation menu