Zyxel Prestige 650 Users Manual P650 13 ADSL Over ISDN Router User's Guide
650 to the manual 9a138206-0931-4e3b-87ba-de41ce3efc83
2015-01-23
: Zyxel Zyxel-Prestige-650-Users-Manual-309969 zyxel-prestige-650-users-manual-309969 zyxel pdf
Open the PDF directly: View PDF 
.
Page Count: 214
| Download | |
| Open PDF In Browser | View PDF |
Prestige 650 ADSL Router User's Guide Version 3.40 August 2002 Prestige 650 ADSL Router Copyright Copyright © 2002 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transmitted in any form or by any means, electronic, mechanical, magnetic, optical, chemical, photocopying, manual, or otherwise, without the prior written permission of ZyXEL Communications Corporation. Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice. Trademarks ZyNOS (ZyXEL Network Operating System) is a registered trademark of ZyXEL Communications, Inc. Other trademarks mentioned in this publication are used for identification purposes only and may be properties of their respective owners. ii Copyright Prestige 650 ADSL Router Federal Communications Commission (FCC) Interference Statement This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operations. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio/television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and the receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. Notice 1 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Certifications Refer to the product page at www.zyxel.com. FCC Statement iii Prestige 650 ADSL Router ZyXEL Limited Warranty ZyXEL warrants to the original end user (purchaser) that this product is free from any defects in materials or workmanship for a period of up to two years from the date of purchase. During the warranty period, and upon proof of purchase, should the product have indications of failure due to faulty workmanship and/or materials, ZyXEL will, at its discretion, repair or replace the defective products or components without charge for either parts or labor, and to whatever extent it shall deem necessary to restore the product or components to proper operating condition. Any replacement will consist of a new or re-manufactured functionally equivalent product of equal value, and will be solely at the discretion of ZyXEL. This warranty shall not apply if the product is modified, misused, tampered with, damaged by an act of God, or subjected to abnormal working conditions. Note Repair or replacement, as provided under this warranty, is the exclusive remedy of the purchaser. This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind of character to the purchaser. To obtain the services of this warranty, contact ZyXEL's Service Center for your Return Material Authorization number (RMA). Products must be returned Postage Prepaid. It is recommended that the unit be insured when shipped. Any returned products without proof of purchase or those with an out-dated warranty will be repaired or replaced (at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary from country to country. Safety Warnings 1. To reduce the risk of fire, use only No. 26 AWG or larger telephone wire. 2. Do not use this product near water, for example, in a wet basement or near a swimming pool. 3. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightening. iv ZyXEL Warranty Prestige 650 ADSL Router Customer Support Please have the following information ready when you contact customer support. • • • • • Product model and serial number. Information in Menu 24.2.1 – System Information. Warranty Information. Date that you received your device. Brief description of the problem and the steps you took to solve it. METHOD E-MAIL SUPPORT/SALES TELEPHONE/FAX WEB SITE/ FTP SITE REGULAR MAIL LOCATION WORLDWIDE support@zyxel.com.tw +886-3-578-3942 www.zyxel.com www.europe.zyxel.com NORTH AMERICA SCANDINAVIA GERMANY MALAYSIA ZyXEL Communications Corp., 6 Innovation Road II, ScienceBased Industrial Park, Hsinchu 300, Taiwan. sales@zyxel.com.tw +886-3-578-2439 ftp.europe.zyxel.com support@zyxel.com +1-714-632-0882 800-255-4101 www.zyxel.com sales@zyxel.com +1-714-632-0858 ftp.zyxel.com support@zyxel.dk +45-3955-0700 www.zyxel.dk sales@zyxel.dk +45-3955-0707 ftp.zyxel.dk support@zyxel.de +49-2405-6909-0 www.zyxel.de sales@zyxel.de +49-2405-6909-99 ZyXEL Deutschland GmbH. Adenauerstr. 20/A4 D-52146 Wuerselen, Germany support@zyxel.com.my +603-795-44-688 www.zyxel.com.my sales@zyxel.com.my +603-795-34-407 Lot B2-06, PJ Industrial Park, Section 13, Jalan Kemajuan, 46200 Petaling Jaya Selangor Darul Ehasn, Malaysia Customer Support ZyXEL Communications Inc., 1650 Miraloma Avenue, Placentia, CA 92870, U.S.A. ZyXEL Communications A/S, Columbusvej 5, 2860 Soeborg, Denmark. v Prestige 650 ADSL Router Table of Contents Copyright .......................................................................................................................................... ii Federal Communications Commission (FCC) Interference Statement ......................................iii ZyXEL Limited Warranty .............................................................................................................. iv Customer Support ............................................................................................................................ v List of Figures ................................................................................................................................. xii List of Tables .................................................................................................................................. xvi Preface ..........................................................................................................................................xviii What is DSL? .................................................................................................................................. xx GETTING STARTED .....................................................................................................................................I Chapter 1 Getting To Know Your Prestige ..................................................................................1-1 1.1 Prestige 650 ADSL Internet Access Router...............................................................................1-1 1.2 Features of the Prestige 650 .......................................................................................................1-1 1.3 Applications for the Prestige 650...............................................................................................1-6 1.3.1 Internet Access...................................................................................................................1-6 1.3.2 LAN to LAN Application ..................................................................................................1-6 Chapter 2 Hardware Installation and Initial Setup....................................................................2-1 2.1 Front Panel LEDs of the P650 ...................................................................................................2-1 2.2 Rear Panel Connections of the Prestige 650 ..............................................................................2-2 2.2.1 DSL Port ............................................................................................................................2-4 2.2.2 Console Port.......................................................................................................................2-4 2.2.3 LAN 10/100M Port ............................................................................................................2-4 2.2.4 Power Port..........................................................................................................................2-4 2.2.5 Reset Button.......................................................................................................................2-4 2.3 Additional Installation Requirements ........................................................................................2-4 2.4 P650 with POTS ........................................................................................................................2-5 2.4.1 Connecting a POTS Splitter...............................................................................................2-5 2.4.2 Telephone Microfilters.......................................................................................................2-6 2.5 P650 With ISDN........................................................................................................................2-6 2.6 Turning On Your Prestige..........................................................................................................2-7 2.7 Configuring Your Prestige For Internet Access.........................................................................2-7 2.7.1 Initial Screen ......................................................................................................................2-7 2.7.2 Entering Password .............................................................................................................2-8 2.8 Resetting the Prestige.................................................................................................................2-8 2.8.1 Methods of Restoring Factory-Defaults.............................................................................2-9 2.8.2 Procedure To Use The Reset Button..................................................................................2-9 2.8.3 Prestige 650 SMT Menu Overview..................................................................................2-10 2.9 Navigating the SMT Interface..................................................................................................2-11 2.9.1 System Management Terminal Interface Summary.........................................................2-12 2.10 Changing the System Password ...............................................................................................2-13 vi Table of Contents Prestige 650 ADSL Router 2.11 General Setup ...........................................................................................................................2-13 2.11.1 Dynamic DNS ..................................................................................................................2-14 2.11.2 Procedure To Configure Menu 1......................................................................................2-14 2.11.3 Procedure to Configure Dynamic DNS............................................................................2-15 2.12 LAN Setup ...............................................................................................................................2-16 2.12.1 LAN Port Filter Setup ......................................................................................................2-17 2.13 Protocol Dependent Ethernet Setup .........................................................................................2-17 Chapter 3 Internet Access .............................................................................................................3-1 3.1 Factory Ethernet Defaults...........................................................................................................3-1 3.2 LANs and WANs .......................................................................................................................3-1 3.2.1 LANs, WANs and the Prestige...........................................................................................3-1 3.3 TCP/IP Parameters .....................................................................................................................3-2 3.3.1 IP Address and Subnet Mask..............................................................................................3-2 3.3.2 Private IP Addresses...........................................................................................................3-3 3.3.3 RIP Setup ...........................................................................................................................3-3 3.3.4 DHCP Configuration..........................................................................................................3-4 3.4 IP Multicast ................................................................................................................................3-5 3.5 IP Policies ..................................................................................................................................3-5 3.6 IP Alias.......................................................................................................................................3-5 3.6.1 IP Alias Setup.....................................................................................................................3-6 3.7 Route IP Setup............................................................................................................................3-8 3.8 TCP/IP Ethernet Setup and DHCP.............................................................................................3-8 3.9 VPI and VCI.............................................................................................................................3-11 3.10 Multiplexing.............................................................................................................................3-11 3.10.1 VC-based Multiplexing ....................................................................................................3-11 3.10.2 LLC-based Multiplexing ..................................................................................................3-11 3.11 Encapsulation ...........................................................................................................................3-11 3.11.1 ENET ENCAP .................................................................................................................3-11 3.11.2 PPP over Ethernet ............................................................................................................3-12 3.11.3 PPPoA ..............................................................................................................................3-12 3.11.4 RFC 1483 .........................................................................................................................3-12 3.12 IP Address Assignment ............................................................................................................3-12 3.12.1 Using PPPoA or PPPoE Encapsulation............................................................................3-12 3.12.2 Using RFC 1483 Encapsulation .......................................................................................3-12 3.12.3 Using ENET ENCAP Encapsulation................................................................................3-12 3.13 Internet Access Configuration..................................................................................................3-13 3.13.1 Traffic Shaping.................................................................................................................3-14 ADVANCED APPLICATIONS................................................................................................................... III Chapter 4 Remote Node Configuration .......................................................................................4-1 4.1 Remote Node Setup....................................................................................................................4-1 4.1.1 Remote Node Profile..........................................................................................................4-1 Table of Contents vii Prestige 650 ADSL Router 4.1.2 Encapsulation and Multiplexing Scenarios ........................................................................4-2 4.1.3 Outgoing Authentication Protocol .....................................................................................4-5 4.2 Remote Node Setup ...................................................................................................................4-6 4.3 Remote Node Filter....................................................................................................................4-8 Chapter 5 Remote Node TCP/IP Configuration .........................................................................5-1 5.1 TCP/IP Configuration ................................................................................................................5-1 5.1.1 Editing TCP/IP Options .....................................................................................................5-1 5.1.2 IP Static Route Setup .........................................................................................................5-5 Chapter 6 Bridging Setup .............................................................................................................6-1 6.1 Bridging in General....................................................................................................................6-1 6.2 Bridge Ethernet Setup ................................................................................................................6-1 6.2.1 Remote Node Bridging Setup ............................................................................................6-1 6.2.2 Bridge Static Route Setup ..................................................................................................6-2 Chapter 7 Network Address Translation (NAT) .........................................................................7-1 7.1 Introduction................................................................................................................................7-1 7.1.1 NAT Definitions ................................................................................................................7-1 7.1.2 What NAT Does ................................................................................................................7-2 7.1.3 How NAT Works...............................................................................................................7-2 7.1.4 NAT Application ...............................................................................................................7-3 7.1.5 NAT Mapping Types .........................................................................................................7-4 7.2 Using NAT.................................................................................................................................7-6 7.2.1 SUA (Single User Account) Versus NAT .........................................................................7-6 7.2.2 Applying NAT ...................................................................................................................7-6 7.3 NAT Setup .................................................................................................................................7-8 7.3.1 Address Mapping Sets .......................................................................................................7-9 7.4 NAT Server Sets — Port Forwarding ......................................................................................7-14 7.4.1 Configuring a Server behind NAT...................................................................................7-15 7.5 General NAT Examples ...........................................................................................................7-18 7.5.1 Example 1: Internet Access Only.....................................................................................7-18 7.5.2 Example 2: Internet Access with an Inside Server...........................................................7-19 7.5.3 Example 3: Multiple Public IP Addresses With Inside Servers .......................................7-20 7.5.4 Example 4: NAT Unfriendly Application Programs........................................................7-24 ADVANCED MANAGEMENT...................................................................................................................III Chapter 8 Filter Configuration ....................................................................................................8-1 8.1 About Filtering...........................................................................................................................8-1 8.2 Configuring a Filter Set .............................................................................................................8-4 8.2.1 Filter Rules Summary Menus ............................................................................................8-7 8.3 Configuring a Filter Rule ...........................................................................................................8-9 8.3.1 TCP/IP Filter Rule .............................................................................................................8-9 8.3.2 Generic Filter Rule...........................................................................................................8-14 8.4 Filter Types and NAT ..............................................................................................................8-16 viii Table of Contents Prestige 650 ADSL Router 8.5 Example Filter..........................................................................................................................8-16 8.6 Applying Filters and Factory Defaults .....................................................................................8-19 8.6.1 Ethernet Traffic ................................................................................................................8-20 8.6.2 Remote Node Filters.........................................................................................................8-20 Chapter 9 SNMP Configuration ...................................................................................................9-1 9.1 About SNMP..............................................................................................................................9-1 9.2 Supported MIBs .........................................................................................................................9-2 9.3 SNMP Configuration .................................................................................................................9-2 9.4 SNMP Traps...............................................................................................................................9-4 Chapter 10 System Information and Diagnosis.........................................................................10-1 10.1 System Status ...........................................................................................................................10-1 10.2 System Information and Console Port Speed...........................................................................10-3 10.2.1 System Information ..........................................................................................................10-3 10.2.2 Console Port Speed ..........................................................................................................10-5 10.3 Log and Trace ..........................................................................................................................10-5 10.3.1 Viewing Error Log ...........................................................................................................10-5 10.3.2 Syslog and Accounting.....................................................................................................10-6 10.4 Diagnostic ................................................................................................................................10-8 Chapter 11 Firmware and Configuration File Maintenance....................................................11-1 11.1 Filename Conventions..............................................................................................................11-1 11.2 Backup Configuration ..............................................................................................................11-2 11.2.1 Backup Configuration ......................................................................................................11-3 11.2.2 Using the FTP Command from the Command Line.........................................................11-3 11.2.3 Example of FTP Commands from the Command Line ....................................................11-3 11.2.4 GUI-based FTP Clients ....................................................................................................11-4 11.2.5 TFTP and FTP over WAN Will Not Work When............................................................11-4 11.2.6 Backup Configuration Using TFTP .................................................................................11-5 11.2.7 TFTP Command Example................................................................................................11-5 11.2.8 GUI-based TFTP Clients..................................................................................................11-5 11.2.9 Backup Via Console Port .................................................................................................11-6 11.3 Restore Configuration ..............................................................................................................11-7 11.3.1 Restore Using FTP ...........................................................................................................11-8 11.3.2 Restore Using FTP Session Example ...............................................................................11-9 11.3.3 Restore Via Console Port .................................................................................................11-9 11.4 Uploading Firmware and Configuration Files........................................................................11-10 11.4.1 Firmware File Upload ....................................................................................................11-10 11.4.2 Configuration File Upload .............................................................................................11-11 11.4.3 FTP File Upload Command from the DOS Prompt Example ........................................11-12 11.4.4 FTP Session Example of Firmware File Upload ............................................................11-12 11.4.5 TFTP File Upload ..........................................................................................................11-12 11.4.6 TFTP Upload Command Example .................................................................................11-13 Table of Contents ix Prestige 650 ADSL Router 11.4.7 Uploading Via Console Port ..........................................................................................11-13 11.4.8 Uploading Firmware File Via Console Port...................................................................11-14 11.4.9 Example Xmodem Firmware Upload Using HyperTerminal ........................................11-14 11.4.10 Uploading Configuration File Via Console Port............................................................11-15 11.4.11 Example Xmodem Configuration Upload Using HyperTerminal..................................11-15 Chapter 12 System Maintenance and Information...................................................................12-1 12.1 Command Interpreter Mode.....................................................................................................12-1 12.2 Call Control Support ................................................................................................................12-2 12.2.1 Budget Management ........................................................................................................12-2 12.3 Time and Date Setting .............................................................................................................12-4 12.3.1 Resetting the Time ...........................................................................................................12-5 Chapter 13 IP Policy Routing .....................................................................................................13-1 13.1 Introduction..............................................................................................................................13-1 13.2 Benefits ....................................................................................................................................13-1 13.3 Routing Policy .........................................................................................................................13-1 13.4 IP Routing Policy Setup...........................................................................................................13-2 13.5 Applying an IP Policy..............................................................................................................13-5 13.5.1 Ethernet IP Policies..........................................................................................................13-5 13.6 IP Policy Routing Example......................................................................................................13-6 Chapter 14 Call Scheduling ........................................................................................................14-1 14.1 Introduction..............................................................................................................................14-1 Chapter 15 Remote Management...............................................................................................15-1 15.1 Telnet .......................................................................................................................................15-1 15.2 FTP ..........................................................................................................................................15-1 15.3 Web..........................................................................................................................................15-1 15.4 Remote Management ...............................................................................................................15-1 15.4.1 Remote Management Setup .............................................................................................15-2 15.4.2 Remote Management Limitations ....................................................................................15-3 15.5 Remote Management and NAT ...............................................................................................15-3 15.6 System Timeout .......................................................................................................................15-3 ADDITIONAL INFORMATION .................................................................................................................. 1 Chapter 16 Troubleshooting .......................................................................................................16-1 16.1 Problems Starting Up the Prestige ...........................................................................................16-1 16.2 Problems with the LAN Interface ............................................................................................16-1 16.3 Problems with the WAN Interface...........................................................................................16-2 16.4 Problems with Internet Access.................................................................................................16-2 16.5 Problems with the Password ....................................................................................................16-3 16.6 Problems with Telnet ...............................................................................................................16-3 Appendix A PPPoE.......................................................................................................................... A Appendix B Virtual Circuit Topology ............................................................................................ C Appendix C Boot Module Commands ............................................................................................E x Table of Contents Prestige 650 ADSL Router Appendix D Power Adapter Specifications....................................................................................G Appendix E TCP/IP .......................................................................................................................... I Index ............................................................................................................................................….O Table of Contents xi Prestige 650 ADSL Router List of Figures Figure 1-1 Internet Access Application...........................................................................................................1-6 Figure 1-2 LAN-to-LAN Application.............................................................................................................1-7 Figure 2-1 Prestige 650 Front Panel ...............................................................................................................2-1 Figure 2-2 Prestige 650 Rear Panel and Connections.....................................................................................2-3 Figure 2-3 Connecting a POTS Splitter ..........................................................................................................2-5 Figure 2-4 Connecting a Microfilter ...............................................................................................................2-6 Figure 2-5 P650 with ADSL over ISDN .........................................................................................................2-7 Figure 2-6 Power-On Display.........................................................................................................................2-8 Figure 2-7 Login Screen .................................................................................................................................2-8 Figure 2-8 Prestige 650 SMT Menu Overview.............................................................................................2-10 Figure 2-9 SMT Main Menu.........................................................................................................................2-12 Figure 2-10 Menu 23 — System Password ..................................................................................................2-13 Figure 2-11 Menu 1 — General Setup..........................................................................................................2-14 Figure 2-12 Configure Dynamic DNS..........................................................................................................2-16 Figure 2-13 Menu 3 — LAN Setup ..............................................................................................................2-17 Figure 2-14 Menu 3.1 — General Ethernet Setup ........................................................................................2-17 Figure 3-1 LAN & WAN IPs ..........................................................................................................................3-2 Figure 3-2 Physical Network ..........................................................................................................................3-6 Figure 3-3 Partitioned Logical Networks .......................................................................................................3-6 Figure 3-4 Menu 3.2 — TCP/IP and DHCP Ethernet Setup ..........................................................................3-6 Figure 3-5 Menu 3.2.1 — IP Alias Setup........................................................................................................3-7 Figure 3-6 Menu 1 — General Setup..............................................................................................................3-8 Figure 3-7 Menu 3.2 — TCP/IP and DHCP Ethernet Setup ...........................................................................3-9 Figure 3-8 Example of Traffic Shaping ........................................................................................................3-14 Figure 3-9 Internet Access Setup ..................................................................................................................3-15 Figure 4-1 Menu 11 — Remote Node Setup ..................................................................................................4-2 Figure 4-2 Menu 11.1 — Remote Node Profile..............................................................................................4-3 Figure 4-3 Remote Node Network Layer Options..........................................................................................4-6 Figure 4-4 Menu 11.5 — Remote Node Filter ................................................................................................4-8 Figure 5-1 Menu 11.6 for VC-based Multiplexing .........................................................................................5-2 Figure 5-2 Menu 11.6 for LLC-based Multiplexing or PPPoA Encapsulation ...............................................5-2 Figure 5-3 Sample IP Addresses for a TCP/IP LAN-to-LAN Connection......................................................5-3 Figure 5-4 Remote Node Network Layer Options..........................................................................................5-4 Figure 5-5 Sample Static Routing Topology...................................................................................................5-6 Figure 5-6 Menu 12 — Static Route Setup.....................................................................................................5-6 Figure 5-7 Menu 12.1 — IP Static Route Setup .............................................................................................5-7 Figure 5-8 Edit IP Static Route .......................................................................................................................5-7 Figure 6-1 Menu 11.3 — Remote Node Bridging Options.............................................................................6-2 Figure 6-2 Menu 12.3.1 — Edit Bridge Static Route .....................................................................................6-3 xii List of Figures Prestige 650 ADSL Router Figure 7-1 How NAT Works .......................................................................................................................... 7-3 Figure 7-2 NAT Application With IP Alias .................................................................................................... 7-4 Figure 7-3 Menu 4 — Applying NAT for Internet Access ............................................................................. 7-6 Figure 7-4 Menu 11.3 — Applying NAT to the Remote Node ...................................................................... 7-8 Figure 7-5 Menu 15 — NAT Setup................................................................................................................ 7-9 Figure 7-6 Menu 15.1 — Address Mapping Sets........................................................................................... 7-9 Figure 7-7 Menu 15.1.255 — SUA Address Mapping Rules....................................................................... 7-10 Figure 7-8 Menu 15.1.1 — First Set .............................................................................................................7-11 Figure 7-9 Menu 15.1.1.1 — Editing/Configuring an Individual Rule in a Set ........................................... 7-13 Figure 7-10 Menu 15.2 — NAT Server Setup.............................................................................................. 7-16 Figure 7-11 Menu 15.2.1 — NAT Server Setup........................................................................................... 7-16 Figure 7-12 Multiple Servers Behind NAT Example ................................................................................... 7-17 Figure 7-13 NAT Example 1 ........................................................................................................................ 7-18 Figure 7-14 Menu 4 — Internet Access & NAT Example ........................................................................... 7-18 Figure 7-15 NAT Example 2 ........................................................................................................................ 7-19 Figure 7-16 Menu 15.2.1 — Specifying an Inside Server............................................................................ 7-20 Figure 7-17 NAT Example 3 ........................................................................................................................ 7-21 Figure 7-18 Example 3: Menu 11.3.............................................................................................................. 7-22 Figure 7-19 Example 3: Menu 15.1.1.1 ....................................................................................................... 7-22 Figure 7-20 Example 3: Final Menu 15.1.1 ................................................................................................. 7-23 Figure 7-21 NAT Example 4 ........................................................................................................................ 7-24 Figure 7-22 Example 4: Menu 15.1.1.1 — Address Mapping Rule............................................................. 7-25 Figure 7-23 Example 4: Menu 15.1.1 — Address Mapping Rules ............................................................. 7-26 Figure 8-1 Outgoing Packet Filtering Process ............................................................................................... 8-2 Figure 8-2 Filter Rule Process........................................................................................................................ 8-3 Figure 8-3 Menu 21 — Filter Set Configuration............................................................................................ 8-4 Figure 8-4 NetBIOS_WAN Filter Rules Summary........................................................................................ 8-5 Figure 8-5 NetBIOS_LAN Filter Rules Summary......................................................................................... 8-5 Figure 8-6 Telnet_WAN Filter Rules Summary ............................................................................................ 8-6 Figure 8-7 PPPoE Filter Rules Summary ...................................................................................................... 8-6 Figure 8-8 FTP_WAN Filter Rules Summary................................................................................................ 8-7 Figure 8-9 WebSet Filter Rules Summary ..................................................................................................... 8-7 Figure 8-10 Menu 21.1.1 — TCP/IP Filter Rule.......................................................................................... 8-10 Figure 8-11 Executing an IP Filter ............................................................................................................... 8-13 Figure 8-12 Menu 21.5.1 — Generic Filter Rule ........................................................................................ 8-14 Figure 8-13 Protocol and Device Filter Sets ................................................................................................ 8-16 Figure 8-14 Sample Telnet Filter ................................................................................................................. 8-17 Figure 8-15 Sample Filter — Menu 21.3.1 .................................................................................................. 8-18 Figure 8-16 Sample Filter Rules Summary — Menu 21.1........................................................................... 8-19 Figure 8-17 Filtering Ethernet Traffic .......................................................................................................... 8-20 Figure 8-18 Filtering Remote Node Traffic ................................................................................................. 8-21 List of Figures xiii Prestige 650 ADSL Router Figure 9-1 SNMP Management Model...........................................................................................................9-1 Figure 9-2 Menu 22 — SNMP Configuration ................................................................................................9-3 Figure 10-1 Menu 24 — System Maintenance .............................................................................................10-1 Figure 10-2 Menu 24.1 — System Maintenance — Status...........................................................................10-2 Figure 10-3 Menu 24.2 — System Information and Console Port Speed.....................................................10-3 Figure 10-4 Menu 24.2.1 — System Maintenance — Information ..............................................................10-4 Figure 10-5 Menu 24.2.2 — System Maintenance — Change Console Port Speed.....................................10-5 Figure 10-6 Menu 24.3 — System Maintenance — Log and Trace .............................................................10-5 Figure 10-7 Sample Error and Information Messages ..................................................................................10-6 Figure 10-8 Menu 24.3.2 — System Maintenance — Syslog and Accounting ............................................10-6 Figure 10-9 Menu 24.4 — System Maintenance — Diagnostic ...................................................................10-8 Figure 11-1 Telnet in Menu 24.5...................................................................................................................11-3 Figure 11-2 FTP Session Example................................................................................................................11-4 Figure 11-3 System Maintenance — Backup Configuration ........................................................................11-6 Figure 11-4 System Maintenance — Starting Xmodem Download Screen..................................................11-6 Figure 11-5 Backup Configuration Example ................................................................................................11-7 Figure 11-6 Successful Backup Confirmation Screen ..................................................................................11-7 Figure 11-7 Telnet into Menu 24.6 ...............................................................................................................11-8 Figure 11-8 Restore Using FTP Session Example ........................................................................................11-9 Figure 11-9 System Maintenance — Restore Configuration ........................................................................11-9 Figure 11-10 System Maintenance — Starting Xmodem Download Screen................................................11-9 Figure 11-11 Restore Configuration Example ............................................................................................11-10 Figure 11-12 Successful Restoration Confirmation Screen ........................................................................11-10 Figure 11-13 Telnet Into Menu 24.7.1 — Upload System Firmware.......................................................... 11-11 Figure 11-14 Telnet Into Menu 24.7.2 — System Maintenance ................................................................. 11-11 Figure 11-15 FTP Session Example of Firmware File Upload ...................................................................11-12 Figure 11-16 Menu 24.7.1 as seen using the Console Port .........................................................................11-14 Figure 11-17 Example Xmodem Upload ....................................................................................................11-14 Figure 11-18 Menu 24.7.2 as seen using the Console Port .........................................................................11-15 Figure 11-19 Example Xmodem Upload ....................................................................................................11-16 Figure 12-1 Command Mode in Menu 24 ....................................................................................................12-1 Figure 12-2 Valid Commands .......................................................................................................................12-2 Figure 12-3 Call Control...............................................................................................................................12-2 Figure 12-4 Budget Management .................................................................................................................12-3 Figure 12-5 Menu 24 — System Maintenance .............................................................................................12-4 Figure 12-6 Menu 24.10 System Maintenance — Time and Date Setting....................................................12-4 Figure 13-1 IP Routing Policy Setup ............................................................................................................13-2 Figure 13-2 Menu 25.1 — Sample IP Routing Policy Setup ........................................................................13-3 Figure 13-3 IP Routing Policy ......................................................................................................................13-4 Figure 13-4 Menu 3.2 — TCP/IP and DHCP Ethernet Setup .......................................................................13-6 Figure 13-5 Menu 11.3 — Remote Node Network Layer Options...............................................................13-6 xiv List of Figures Prestige 650 ADSL Router Figure 13-6 Example of IP Policy Routing .................................................................................................. 13-7 Figure 13-7 IP Routing Policy Example ...................................................................................................... 13-8 Figure 13-8 IP Routing Policy .................................................................................................................... 13-9 Figure 13-9 Applying IP Policies ................................................................................................................. 13-9 Figure 14-1 Menu 26 — Schedule Setup ..................................................................................................... 14-1 Figure 14-2 Schedule Set Setup ................................................................................................................... 14-2 Figure 14-3 Applying Schedule Set(s) to a Remote Node (PPPoE)............................................................. 14-4 Figure 15-1 Telnet Configuration on a TCP/IP Network ............................................................................. 15-1 Figure 15-2 Menu 24.11 — Remote Management Control.......................................................................... 15-2 List of Figures xv Prestige 650 ADSL Router List of Tables Table 2-1 Front Panel LED Description ........................................................................................................ 2-1 Table 2-2 Main Menu Commands ................................................................................................................2-11 Table 2-3 Main Menu Summary .................................................................................................................. 2-12 Table 2-4 General Setup Menu Fields.......................................................................................................... 2-15 Table 2-5 Configure Dynamic DNS Menu Fields........................................................................................ 2-16 Table 3-1 IP Alias Setup Menu Fields............................................................................................................ 3-7 Table 3-2 DHCP Ethernet Setup Menu Fields ............................................................................................... 3-9 Table 3-3 TCP/IP Ethernet Setup Menu Fields ............................................................................................ 3-10 Table 3-4 Internet Account Information....................................................................................................... 3-13 Table 3-5 Internet Access Setup Menu Fields.............................................................................................. 3-15 Table 4-1 Remote Node Profile Menu Fields ................................................................................................ 4-3 Table 4-2 Remote Node Network Layer Options .......................................................................................... 4-6 Table 5-1 TCP/IP-Related Fields in Menu 11.1 — Remote Node Profile ..................................................... 5-3 Table 5-2 TCP/IP Remote Node Configuration ............................................................................................. 5-4 Table 5-3 Edit IP Static Route Menu Fields................................................................................................... 5-7 Table 6-1 Remote Node Bridge Options........................................................................................................ 6-2 Table 6-2 Edit Bridge Static Route Menu Fields ........................................................................................... 6-3 Table 7-1 NAT Definitions............................................................................................................................. 7-1 Table 7-2 NAT Mapping Types...................................................................................................................... 7-5 Table 7-3 Applying NAT in Menus 4 & 11.3 ................................................................................................. 7-8 Table 7-4 SUA Address Mapping Rules ...................................................................................................... 7-10 Table 7-5 Fields in Menu 15.1.1 .................................................................................................................. 7-12 Table 7-6 Menu 15.1.1.1 — Editing/Configuring an Individual Rule in a Set ............................................ 7-13 Table 7-7 Services and Port Numbers.......................................................................................................... 7-14 Table 8-1 Abbreviations Used in the Filter Rules Summary Menu ............................................................... 8-8 Table 8-2 Rule Abbreviations Used ............................................................................................................... 8-8 Table 8-3 TCP/IP Filter Rule Menu Fields .................................................................................................. 8-10 Table 8-4 Generic Filter Rule Menu Fields ................................................................................................. 8-15 Table 8-5 Filter Sets Table ........................................................................................................................... 8-20 Table 9-1 SNMP Configuration Menu Fields ................................................................................................ 9-3 Table 9-2 SNMP Traps................................................................................................................................... 9-4 Table 9-3 Ports and Permanent Virtual Circuits............................................................................................. 9-4 Table 10-1 System Maintenance — Status Menu Fields ............................................................................. 10-2 Table 10-2 Fields in System Maintenance ................................................................................................... 10-4 Table 10-3 System Maintenance Menu — Syslog Parameters .................................................................... 10-6 Table 10-4 System Maintenance Menu — Diagnostic................................................................................. 10-8 Table 11-1 Filename Conventions ................................................................................................................11-2 Table 11-2 General Commands for GUI-based FTP Clients.........................................................................11-4 Table 11-3 General Commands for GUI-based TFTP Clients ......................................................................11-5 xvi List of Tables Prestige 650 ADSL Router Table 12-1 Budget Management .................................................................................................................. 12-3 Table 12-2 Time and Date Setting Fields ..................................................................................................... 12-5 Table 13-1 IP Routing Policy Setup ............................................................................................................. 13-3 Table 13-2 IP Routing Policy ....................................................................................................................... 13-4 Table 14-1 Schedule Set Setup Fields .......................................................................................................... 14-2 Table 15-1 Menu 24.11 — Remote Management Control ........................................................................... 15-2 Table 16-1 Troubleshooting the Start-Up of Your Prestige .......................................................................... 16-1 Table 16-2 Troubleshooting the LAN Interface ........................................................................................... 16-1 Table 16-3 Troubleshooting the WAN Interface .......................................................................................... 16-2 Table 16-4 Troubleshooting Internet Access ................................................................................................ 16-2 Table 16-5 Troubleshooting the Password ................................................................................................... 16-3 Table 16-6 Troubleshooting Telnet............................................................................................................... 16-3 List of Tables xvii Prestige 650 ADSL Router Preface Congratulations on your purchase of the Prestige 650 ADSL Internet Access Router. There are two Prestige 650 models, one for ADSL over POTS (Plain Old Telephone System) and one for ADSL over ISDN (Integrated Synchronous Digital System). Both models are discussed together in this guide. The P650 ADSL router can run maximum upstream transmission rates of up to 832Kbps and maximum downstream transmission rates of 8Mbps. The actual rate depends on the copper category of your telephone wire, distance from the central office and the type of ADSL service subscribed to. See the What is DSL section for more background information on DSL and ADSL. The P650's 10/100M auto-negotiating LAN interface enables fast data transfer of either 10Mbps or 100Mbps in either half-duplex or full-duplex mode depending on your Ethernet network. Your Prestige is easy to install and configure. All functions of the Prestige are software configurable via the SMT (System Management Terminal) and web configurator. Advanced users may configure the Prestige using CLI (Command Line Interface) commands. Don’t forget to register your Prestige (fast, easy online registration at www.zyxel.com) for free future product updates and information. About This User's Guide This user's guide covers all aspects of Prestige operations and shows you how to get the best out of the multiple advanced features of your ADSL Internet Access Router using the SMT. It is designed to guide you through the correct configuration of your Prestige 650 for various applications. Related Documentation Supporting Disk More detailed information and examples can be found in our included disk (as well as on the zyxel.com web site). This disk contains information on configuring your Prestige for Internet Access, general and advanced FAQs, Application Notes, Troubleshooting, a reference for CI Commands and bundled software. Read Me First Our Read Me First is designed to help you get up and running right away. It contains a detailed easy-to-follow connection diagram, default settings, handy checklists and information on setting up your network and configuring for Internet access. ZyXEL Web Site The ZyXEL download library at www.zyxel.com contains additional support documentation and a glossary. xviii Preface Prestige 650 ADSL Router Syntax Conventions • “Type” means for you to type one or more characters and press the carriage return. “Select” or “Choose” means for you to select one predefined choices. • The SMT menu titles and labels are in Bold Times New Roman font. Predefined field choices are in Bold Arial font. Command and arrow keys are enclosed in square brackets. [ENTER] means the Enter, or carriage return key; [ESC] means the Escape key and [SPACE BAR] means the Space Bar. • For brevity’s sake, we will use “e.g.,” as a shorthand for “for instance”, and “i.e.,” for “that is” or “in other words” throughout this manual. • The Prestige 650 router may be referred to as the P650 or the Prestige in this user’s guide. The following section offers some background information on DSL. Skip to Chapter 1 if you wish to begin working with your router right away. Preface xix Prestige 650 ADSL Router What is DSL? DSL (Digital Subscriber Line) technology enhances the data capacity of the existing twisted-pair wire that runs between the local telephone company switching offices and most homes and offices. While the wire itself can handle higher frequencies, the telephone switching equipment is designed to cut off signals above 4,000 Hz to filter noise off the voice line, but now everybody is searching for ways to get more bandwidth to improve access to the Web - hence DSL technologies. There are actually seven types of DSL service, ranging in speeds from 16 Kbits/sec to 52 Mbits/sec. The services are either symmetrical (traffic flows at the same speed in both directions), or asymmetrical (the downstream capacity is higher than the upstream capacity). Asymmetrical services (ADSL) are suitable for Internet users because more information is usually downloaded than uploaded. For example, a simple button click in a web browser can start an extended download that includes graphics and text. As data rates increase, the carrying distance decreases. That means that users who are beyond a certain distance from the telephone company’s central office may not be able to obtain the higher speeds. A DSL connection is a point-to-point dedicated circuit, meaning that the link is always up and there is no dialing required. What is ADSL? It is an asymmetrical technology, meaning that the downstream data rate is much higher than the upstream data rate. As mentioned, this works well for a typical Internet session in which more information is downloaded, for example, from Web servers, than is uploaded. ADSL operates in a frequency range that is above the frequency range of voice services, so the two systems can operate over the same cable. xx What is DSL? Getting Started Part I: GETTING STARTED This part is structured as a step-by-step guide to help you connect, install and set up your Prestige to operate on your network and to access the Internet. Described are Key Features and Applications, Hardware Installation, Initial Setup and Internet Access. I Prestige 650 ADSL Router Chapter 1 Getting To Know Your Prestige This chapter describes the key features and applications of your Prestige. 1.1 Prestige 650 ADSL Internet Access Router Your Prestige integrates a high-speed 10/100Mbps auto-negotiating LAN interface and one high-speed ADSL port into a single package. The Prestige is ideal for high-speed Internet browsing and making LANto-LAN connections to remote networks. 1.2 Features of the Prestige 650 Your Prestige is packed with a number of features that give it the flexibility to provide a complete networking solution for almost any user. High Speed Internet Access Your Prestige ADSL router can support downstream transmission rates of up to 8Mbps and upstream transmission rates of 832 Kbps. Prestige 650 with ADSL over POTS also supports rate management. PPPoE Support (RFC2516) PPPoE (Point-to-Point Protocol over Ethernet) emulates a dial-up connection. It allows your ISP to use their existing network configuration with newer broadband technologies such as ADSL. The PPPoE driver on the Prestige is transparent to the computers on the LAN, which see only Ethernet and are not aware of PPPoE thus saving you from having to manage PPPoE clients on individual computers. Getting To Know Your Prestige 1-1 Prestige 650 ADSL Router NAT for Single-IP-address Internet Access The Prestige's SUA (Single User Account) feature allows multiple-user Internet access for the cost of a single IP account. NAT supports popular Internet applications such as MS traceroute, CuSeeMe, IRC, RealPlayer, VDOLive, Quake, and PPTP. No configuration is needed to support these applications. 10/100M Auto-negotiation Ethernet/Fast Ethernet Interface This auto-negotiation feature allows the Prestige to detect the speed of incoming transmissions and adjust appropriately without manual intervention. It allows data transfer of either 10 Mbps or 100 Mbps in either half-duplex or full-duplex mode depending on your Ethernet network. Dynamic DNS Support With Dynamic DNS support, you can have a static hostname alias for a dynamic IP address, allowing the host to be more easily accessible from various locations on the Internet. You must register for this service with a Dynamic DNS client. Multiple PVC (Permanent Virtual Circuits) Support Your Prestige supports up to 8 PVC’s. ADSL Transmission Rate Standards ♦ Full-Rate (ANSI T1.413, Issue 2; G.dmt (G.992.1) with line rate support of up to 8 Mbps downstream and 832 Kbps upstream. ♦ G.lite (G.992.2) with line rate support of up to 1.5Mbps downstream and 512Kbps upstream. ♦ Supports Multi-Mode standard (ANSI T1.413, Issue 2; G.dmt (G.992.1); G.994.1 and G.996.1 (for ISDN only); G.991.1;G.lite (G992.2)). ♦ TCP/IP (Transmission Control Protocol/Internet Protocol) network layer protocol. ♦ ATM Forum UNI 3.1/4.0 PVC. ♦ Supports up to 8 PVCs (UBR, CBR). ♦ Multiple Protocols over AAL5 (RFC 1483). ♦ PPP over AAL5 (RFC 2364). 1-2 Getting To Know Your Prestige Prestige 650 ADSL Router ♦ PPP over Ethernet over AAL5 (RFC 2516). ♦ RFC 1661. ♦ PPP over PAP (RFC 1334). ♦ PPP over CHAP (RFC 1994). • Protocol Support ♦ DHCP Support DHCP (Dynamic Host Configuration Protocol) allows the individual clients (computers) to obtain the TCP/IP configuration at start-up from a centralized DHCP server. The Prestige has built-in DHCP server capability enabled by default. It can assign IP addresses, an IP default gateway and DNS servers to DHCP clients. The Prestige can now also act as a surrogate DHCP server (DHCP Relay) where it relays IP address assignment from the actual real DHCP server to the clients. ♦ IP Alias IP Alias allows you to partition a physical network into logical networks over the same Ethernet interface. The Prestige supports three logical LAN interfaces via its single physical Ethernet interface with the Prestige itself as the gateway for each LAN network. ♦ IP Policy Routing (IPPR) Traditionally, routing is based on the destination address only and the router takes the shortest path to forward a packet. IP Policy Routing (IPPR) provides a mechanism to override the default routing behavior and alter the packet forwarding based on the policy defined by the network administrator. ♦ PPP (Point-to-Point Protocol) link layer protocol. ♦ Transparently bridging for unsupported network layer protocols. ♦ RIP I/RIP II ♦ IGMP Proxy ♦ ICMP support Getting To Know Your Prestige 1-3 Prestige 650 ADSL Router ♦ IP QoS support ♦ MIB II support (RFC 1213) Networking Compatibility Your Prestige is compatible with the major ADSL DSLAM (Digital Subscriber Line Access Multiplexer) providers, making configuration as simple as possible for you. Multiplexing The Prestige Series supports VC-based and LLC-based multiplexing. Encapsulation The Prestige Series supports PPPoA (RFC 2364 - PPP over ATM Adaptation Layer 5), RFC 1483 encapsulation over ATM, MAC encapsulated routing (ENET Encapsulation) as well as PPP over Ethernet (RFC 2516). Network Management ♦ Menu driven SMT (System Management Terminal) management ♦ Embedded Web Configurator ♦ CLI (Command Line Interpreter) ♦ Remote SMT session via Telnet ♦ SNMP manageable ♦ Local SMT session via console port ♦ DHCP Server/Client ♦ Built-in Diagnostic Tools ♦ Syslog ♦ Telnet Support (Password-protected telnet access to internal configuration manager) ♦ TFTP/FTP server, firmware upgrade and configuration backup/support supported ♦ Supports OAM F4/F5 loop-back, AIS and RDI OAM cells 1-4 Getting To Know Your Prestige Prestige 650 ADSL Router • Remote Management • Other PPPoE Features • ♦ PPPoE idle time out ♦ PPPoE Dial on Demand Diagnostics Capabilities ♦ The Prestige can perform self-diagnostic tests. These tests check the integrity of the following circuitry: ♦ FLASH memory ♦ ADSL circuitry ♦ RAM ♦ LAN port Filters The Prestige's packet filtering functions allows added network security and management. Ease of Installation Your Prestige is designed for quick, intuitive and easy installation. Housing Your Prestige's all new compact and ventilated housing minimizes space requirements making it easy to position anywhere in your busy office. The Prestige is easy to mount on your wall. Getting To Know Your Prestige 1-5 Prestige 650 ADSL Router 1.3 Applications for the Prestige 650 1.3.1 Internet Access The Prestige is the ideal high-speed Internet access solution. Your Prestige supports the TCP/IP protocol, which the Internet uses exclusively. It is compatible with all major ADSL DSLAM (Digital Subscriber Line Access Multiplexer) providers. A DSLAM is a rack of ADSL line cards with data multiplexed into a backbone network interface/connection (for example, T1, OC3, DS3, ATM or Frame Relay). Think of it as the equivalent of a modem rack for ADSL. A typical Internet Access application is shown below. Figure 1-1 Internet Access Application Internet Single User Account For a SOHO (Small Office/Home Office) environment, your Prestige offers the Single User Account (SUA) feature that allows multiple users on the LAN (Local Area Network) to access the Internet concurrently for the cost of a single IP address. 1.3.2 LAN to LAN Application You can use the Prestige to connect two geographically dispersed networks over the ADSL line. A typical LAN-to-LAN application for your Prestige is shown as follows. 1-6 Getting To Know Your Prestige Prestige 650 ADSL Router Figure 1-2 LAN-to-LAN Application Getting To Know Your Prestige 1-7 Prestige 650 ADSL Router Chapter 2 Hardware Installation and Initial Setup This chapter describes the physical features of the Prestige and how to make cable connections. 2.1 Front Panel LEDs of the P650 The LEDs on the front panel indicate the operational status of your Prestige Figure 2-1 Prestige 650 Front Panel Table 2-1 Front Panel LED Description LED PWR SYS LAN 10M COLOR Green STATUS DESCRIPTION On The Prestige is receiving power. Blinking The Prestige is performing a self-test. Off The Prestige is not receiving power. On The Prestige is functioning properly. Blinking The Prestige is rebooting. Off The system is not ready or has malfunctioned. Orange On Power gasp action. Power to the Prestige is too low. Green On The Prestige has a successful 10Mb Ethernet connection. Blinking The Prestige is sending/receiving data. Off The Prestige does not have 10Mb Ethernet connection. Green Hardware Installation and Initial Setup 2-1 Prestige 650 ADSL Router LED COLOR LAN 100M Orange DSL ACT 2.2 Green Green STATUS DESCRIPTION On The Prestige has a successful 100Mb Ethernet connection. Blinking The Prestige is sending/receiving data. Off The Prestige does not have 100Mb Ethernet connection. On The Prestige is linked successfully to a DSLAM. Blinking The Prestige is initializing the DSL line. Off The DSL link is down. On The Prestige has a successful DSL connection. Blinking The Prestige is sending/receiving data. Off The system is ready, but is not sending/receiving data. Rear Panel Connections of the Prestige 650 The following figure shows the rear panel of your Prestige. 2-2 Hardware Installation and Initial Setup Prestige 650 ADSL Router Figure 2-2 Prestige 650 Rear Panel and Connections Hardware Installation and Initial Setup 2-3 Prestige 650 ADSL Router 2.2.1 DSL Port Connect the Prestige directly to the wall jack using the included DSL cable. Connect a microfilter(s) between the wall jack and your telephone(s). A microfilter acts as low-pass filter (voice transmission takes place in the 0 to 4KHz bandwidth) and is an optional purchase. 2.2.2 Console Port Use terminal emulator software on a computer for configuring your Prestige via console port. Connect the 7-pin end of the supplied console cable to the console port of the Prestige and the 9-pin female end to a serial port (COM1, COM2 or other COM port) of your computer. 2.2.3 LAN 10/100M Port Ethernet 10Base-T/100Base-T networks use Shielded Twisted Pair (STP) cable with RJ-11 connectors (POTS) that look like a bigger telephone plug with 8 pins. Use the crossover cable to connect your Prestige to a computer directly or use a straight-through Ethernet cable to connect to an external hub, then connect one end of the straight-through cable from the hub to the NIC on the computer. When the Prestige is on and properly connected to a computer or a hub, the corresponding LAN LED on the front panel turns on. 2.2.4 Power Port Connect the power adapter to the port labeled POWER on the rear panel of your Prestige. To avoid damage to the Prestige, make sure you use the correct power adapter. Refer to the Power Adapter Specification Appendix for this information. 2.2.5 Reset Button Refer to section 2.8 for information on the RESET button. 2.3 Additional Installation Requirements A computer with an Ethernet 10Base-T/100Base-T NIC (Network Interface Card). A computer equipped with communications software (for example, Hyper Terminal in Windows 95) configured to the following parameters: VT100 terminal emulation. 9600 baud rate. 2-4 Hardware Installation and Initial Setup Prestige 650 ADSL Router Parity set to none, 8 data bits, 1 stop bit. Flow control set to none. After the Prestige has been successfully connected to your network, you can make future changes to the configuration via Telnet or the embedded web configurator. 2.4 P650 with POTS Sections 2.4.1 and 2.4.2 relate to people who use their P650 with ADSL over POTS (analog telephone service) only. 2.4.1 Connecting a POTS Splitter This is for the Prestige that follows the Full Rate (G.dmt) standard only. One major difference between ADSL and dial-up modems is the optional telephone splitter. This device keeps the telephone and ADSL signals separated, giving them the capability to provide simultaneous Internet access and telephone service on the same line. Splitters also eliminate the destructive interference conditions caused by telephone sets. The purchase of a POTS splitter is optional. Noise generated from a telephone in the same frequency range, as the ADSL signal can be disruptive to the ADSL signal. In addition the impedance of a telephone when off-hook may be so low that it shunts the strength of the ADSL signal. When a POTS splitter is installed at the entry point, where the line comes into the home, it will filter the telephone signals before combining the ADSL and telephone signals transmitted and received. The issues of noise and impedance are eliminated with a single POTS splitter installation. A telephone splitter is easy to install as shown in the following figure. Figure 2-3 Connecting a POTS Splitter Step 1. Connect the side labeled “Phone” to your telephone. Hardware Installation and Initial Setup 2-5 Prestige 650 ADSL Router Step 2. Connect the side labeled “Modem” to your Prestige. Step 3. Connect the side labeled “Line” to the telephone wall jack. 2.4.2 Telephone Microfilters Telephone voice transmissions take place in the lower frequency range, 0 - 4KHz, while ADSL transmissions take place in the higher bandwidth range, above 4KHz. A microfilter acts as a low-pass filter, for your telephone, to ensure that ADSL transmissions do not interfere with your telephone voice transmissions. The purchase of a telephone microfilter is optional. Step 1. Connect a phone cable from the wall jack to the single jack end of the Y- Connector. Step 2. Connect a cable from the double jack end of the Y-Connector to the “wall side” of the microfilter. Step 3. Connect another cable from the double jack end of the Y-Connector to the Prestige. Step 4. Connect the “phone side” of the microfilter to your telephone as shown in the following figure. Figure 2-4 Connecting a Microfilter 2.5 P650 With ISDN This section relates to people who use their P650 with ADSL over ISDN (digital telephone service) only. The following is an example installation for the P650 with ISDN. 2-6 Hardware Installation and Initial Setup Prestige 650 ADSL Router Figure 2-5 P650 with ADSL over ISDN 2.6 Turning On Your Prestige At this point, you should have connected the DSL, LAN 10/100M, console and power ports to the appropriate devices. Make sure the power adapter is plugged into an appropriate power source and the power switch (located on the back of your Prestige) is “on” (or pressed). 2.7 Configuring Your Prestige For Internet Access Configure your Prestige for Internet access using: Web Configurator (refer to the Read Me First) SMT (System Management Terminal). Access the SMT via: o LAN or WAN using Telnet o Console port using terminal emulation software The remainder of this user’s guide shows you how to configure the Prestige for Internet access using SMT screens. There are also some sections in this guide that also focus on using Telnet to configure the Prestige. 2.7.1 Initial Screen When you turn on your Prestige, it performs several internal tests as well as line initialization. After the initialization, the Prestige asks you to press [ENTER] to continue, as shown. Hardware Installation and Initial Setup 2-7 Prestige 650 ADSL Router Copyright (c) 1994 - 2002 ZyXEL Communications Corp. initialize ch =0, ethernet address: 00:a0:c5:01:23:45 HWSAR (FPGA) : programing (11969) ... done HWSAR (FPGA) : testing . . . done WAN Channel init . . . . done Loading ADSL modem F/W ............................................... done Press ENTER to continue... Figure 2-6 Power-On Display 2.7.2 Entering Password The login screen appears after you press [ENTER], prompting you to enter the password, as shown next. For your first login, enter the default password “1234”. As you type the password, the screen displays an “X” for each character you type. Please note that if there is no activity for longer than five minutes after you log in, your Prestige will automatically log you out and will display a blank screen. If you see a blank screen, press [ENTER] to display the login screen again. Enter Password : XXXX Figure 2-7 Login Screen 2.8 Resetting the Prestige If you forget your password or cannot access the Prestige, you will need to reload the factory-default configuration file. Uploading this configuration file replaces the current configuration file with the factorydefault configuration file. This means that you will lose all configurations that you had previously and the speed of the console port will be reset to the default of 9600bps with 8 data bit, no parity, one stop bit and flow control set to none. The password will be reset to “1234” and the LAN IP address to 192.168.1.1also. To obtain the default configuration file, download it from the ZyXEL FTP site, unzip it and save it in a folder. Turn the Prestige off and then on to begin a session. When you turn on the Prestige again you will see the initial screen. When you see the message “Press any key to enter Debug Mode within 3 seconds” press any key to enter debug mode. To upload the configuration file, do the following: 2-8 Hardware Installation and Initial Setup Prestige 650 ADSL Router 1. Type atlc after the Enter Debug Mode message. 2. Wait for the Starting XMODEM upload message before activating XMODEM upload on your terminal. 3. After a successful firmware upload, type atgo to restart the Prestige. The Prestige is now reinitialized with a default configuration file including the default password of “1234”. 2.8.1 Methods of Restoring Factory-Defaults You can erase the current configuration and restore factory defaults in three ways: a. Use the web configurator (see the web configurator HTML help). b. Upload the default configuration file via the console port as described above. See later in this User’s Guide for more information on how to transfer the configuration file to your Prestige using the SMT menus. c. Use the RESET button on the rear panel of the Prestige (see the next section). 2.8.2 Procedure To Use The Reset Button 1. Turn your Prestige off and then on. Make sure the SYS led is on (not blinking). 2. Press the RESET button for five seconds and then release it. If the SYS LED begins to blink, the defaults have been restored and the Prestige restarts. Hardware Installation and Initial Setup 2-9 Prestige 650 ADSL Router 2.8.3 Prestige 650 SMT Menu Overview The following figure gives you an overview of the various SMT menu screens of your Prestige. Figure 2-8 Prestige 650 SMT Menu Overview 2-10 Hardware Installation and Initial Setup Prestige 650 ADSL Router 2.9 Navigating the SMT Interface The SMT (System Management Terminal) is the interface that you use to configure your Prestige. Several operations that you should be familiar with before you attempt to modify the configuration are listed in the table below. Table 2-2 Main Menu Commands OPERATION KEYSTROKE DESCRIPTION Move down to another menu [ENTER] To move forward to a submenu, type in the number of the desired submenu and press [ENTER]. Move up to a previous menu [ESC] Press [ESC] to move back to the previous menu. Fields beginning with “Edit” lead to hidden menus and have a Move to a “hidden” Press [SPACE BAR] to change No default setting of No. Press [SPACE BAR] once to change No to menu to Yes then press Yes, then press [ENTER] to go to the “hidden” menu. [ENTER]. Move the cursor [ENTER] or Within a menu, press [ENTER] to move to the next field. You can [UP]/[DOWN] arrow also use the [UP]/[DOWN] arrow keys to move to the previous keys. and the next field, respectively. Entering information Type in or press You need to fill in two types of fields. The first requires you to type [SPACE BAR], then in the appropriate information. The second allows you to cycle press [ENTER]. through the available choices by pressing [SPACE BAR]. Required fields All fields with the symbol must be filled in order to be able to save the new configuration. N/A fieldsSome of the fields in the SMT will show a . This symbol refers to an option that is Not Applicable. Save your configuration [ENTER] Save your configuration by pressing [ENTER] at the message “Press ENTER to confirm or ESC to cancel”. Saving the data on the screen will take you, in most cases to the previous menu. Exit the SMT Type 99, then press Type 99 at the main menu prompt and press [ENTER] to exit the [ENTER]. SMT interface. After you enter the password, the SMT displays the main menu, as shown next. Hardware Installation and Initial Setup 2-11 Prestige 650 ADSL Router Copyright (c) 1994 - 2002 ZyXEL Communications Corp. Prestige 650 Main Menu Getting Started 1. General Setup 3. LAN Setup 4. Internet Access Setup Advanced Applications 11. Remote Node Setup 12. Static Routing Setup 15. NAT Setup Advanced Management 21. Filter Set Configuration 22. SNMP Configuration 23. System Password 24. System Maintenance 25. IP Routing Policy Setup 26. Schedule Setup 99. Exit Enter Menu Selection Number:_ Figure 2-9 SMT Main Menu The SMT menu continually improves and changes with new firmware upgrades. Check the release notes at www.zyxel.com to find the most recent upgrades and information. 2.9.1 System Management Terminal Interface Summary Table 2-3 Main Menu Summary # MENU TITLE DESCRIPTION 1 General Setup Use this menu to set up your general information. 3 LAN Setup Use this menu to set up your LAN connection. 4 Internet Access Setup A quick and easy way to set up an Internet connection. 11 Remote Node Setup Use this menu to set up the Remote Node for LAN-to-LAN connection, including Internet connection. 12 Static Routing Setup Use this menu to set up static routes. 15 NAT Setup Use this menu to specify inside servers when NAT is enabled. 21 Filter Set Configuration Use this menu to set up filters to provide security, etc. 22 SNMP Configuration Use this menu to set up SNMP related parameters. 23 System Password Use this menu to change your password. 24 System Maintenance This menu provides system status, diagnostics, software upload, etc. 25 IP Routing Policy Setup Use this menu to configure your IP routing policy. 26 Schedule Setup Use this menu to schedule outgoing calls. 99 Exit Use this to exit from SMT and return to a blank screen. 2-12 Hardware Installation and Initial Setup Prestige 650 ADSL Router 2.10 Changing the System Password Change the Prestige default password by following the steps shown next. Step 1. Enter 23 in the main menu to display Menu 23 - System Password as shown next. Step 2. Type your existing system password in the Old Password field, for example “1234”, and press [ENTER]. Menu 23 – System Password Old Password= **** New Password= ? Retype to confirm= ? Enter here to CONFIRM or ESC to CANCEL: Figure 2-10 Menu 23 — System Password Step 3. Type your new system password in the New Password field (up to 30 characters), and press [ENTER]. Step 4. Re-type your new system password in the Retype to confirm field for confirmation and press [ENTER]. Note that as you type a password, the screen displays an “*” for each character you type. 2.11 General Setup Menu 1 — General Setup contains administrative and system-related information (shown next). The System Name field is for identification purposes. However, because some ISPs check this name you should enter your computer's "Computer Name". • In Windows 95/98 click Start -> Settings -> Control Panel -> Network. Click the Identification tab, note the entry for the Computer name field and enter it as the Prestige System Name. • In Windows 2000 click Start->Settings->Control Panel and then double-click System. Click the Network Identification tab and then the Properties button. Note the entry for the Computer name field and enter it as the Prestige System Name. • In Windows XP, click start -> My Computer -> View system information and then click the Computer Name tab. Note the entry in the Full computer name field and enter it as the Prestige System Name. Hardware Installation and Initial Setup 2-13 Prestige 650 ADSL Router The Domain Name entry is what is propagated to the DHCP clients on the LAN. If you leave this blank, the domain name obtained by DHCP from the ISP is used. While you must enter the host name (System Name) on each individual computer, the domain name can be assigned from the Prestige via DHCP. 2.11.1 Dynamic DNS Dynamic DNS (Domain Name System) allows you to update your current dynamic IP address with one or many dynamic DNS services so that anyone can contact you (in NetMeeting, CU-SeeMe or other services). You can also access your FTP server or Web site on your own computer using a DNS-like address (for example, myhost.dhs.org, where myhost is a name of your choice) which will never change instead of using an IP address that changes each time you reconnect. Your friends or relatives will always be able to call you even if they don't know your IP address. First of all, you need to have registered a dynamic DNS account with www.dyndns.org. This is for people with a dynamic IP from their ISP or DHCP server that would still like to have a DNS name. To use this service, you must register with the Dynamic DNS service provider. The Dynamic DNS service provider will give you a password or key. The Prestige supports www.dyndns.org. You can apply to this service provider for Dynamic DNS service. DYNDNS Wildcard Enabling the wildcard feature for your host causes *.yourhost.dyndns.org to be aliased to the same IP address as yourhost.dyndns.org. This feature is useful if you want to be able to use, for example, www.yourhost.dyndns.org and still reach your hostname. 2.11.2 Procedure To Configure Menu 1 Step 1. Enter 1 in the Main Menu to open Menu 1 — General Setup (shown next). Menu 1 - General Setup System Name= ? Location= Contact Person's Name= Domain Name= Edit Dynamic DNS= No Route IP= Yes Bridge= No Press ENTER to Confirm or ESC to Cancel: Figure 2-11 Menu 1 — General Setup Step 2. 2-14 Fill in the required fields. Refer to the table shown next for more information about these fields. Hardware Installation and Initial Setup Prestige 650 ADSL Router Table 2-4 General Setup Menu Fields FIELD DESCRIPTION EXAMPLE System Name Choose a descriptive name for identification purposes. This name can be up to 30 alphanumeric characters long. Spaces are not allowed, but dashes “-” and underscores "_" are accepted. P650 Location (optional) Enter the geographic location (up to 31 characters) of your Prestige. MyHouse Contact Person's Name (optional) Enter the name (up to 30 characters) of the person in charge of this Prestige. JohnDoe Domain Name Enter the domain name (if you know it) here. If you leave this field blank, the ISP may assign a domain name via DHCP. You can go to menu 24.8 and type “sys domainname” to see the current domain name used by your gateway. If you want to clear this field just press the [SPACE BAR]. The domain name entered by you is given priority over the ISP-assigned domain name. Edit Dynamic DNS Press the [SPACE BAR] to select Yes or No (default). Select Yes to configure Menu 1.1 — Configure Dynamic DNS (discussed next). No Route IP Set this field to Yes to enable or No to disable IP routing. You must enable IP routing for Internet access. Yes Bridge Turn on/off bridging for protocols not supported (for example, SNA) or not turned on in the previous Route IP field. Select Yes to turn bridging on; select No to turn bridging off. No 2.11.3 Procedure to Configure Dynamic DNS Step 1. To configure Dynamic DNS, go to Menu 1 — General Setup and select Yes in the Edit Dynamic DNS field. Press [ENTER] to display Menu 1.1 — Configure Dynamic DNS as shown next. Hardware Installation and Initial Setup 2-15 Prestige 650 ADSL Router Menu 1.1 - Configure Dynamic DNS Service Provider = WWW.DynDNS.ORG Active= Yes Host= me.ddns.org EMAIL= mail@mailserver USER= username Password= ********* Enable Wildcard= No Press ENTER to confirm or ESC to cancel: Figure 2-12 Configure Dynamic DNS Follow the instructions in the next table to configure Dynamic DNS parameters. Table 2-5 Configure Dynamic DNS Menu Fields FIELD DESCRIPTION EXAMPLE Service Provider This is the name of your Dynamic DNS service provider. Active Press [SPACE BAR] to select Yes and then press [ENTER] to make dynamic DNS active. Host Enter the domain name assigned to your Prestige by your Dynamic DNS provider. EMAIL Enter your e-mail address. USER Enter your user name. Password Enter the password assigned to you. Enable Wildcard Your Prestige supports DYNDNS Wildcard. Press [SPACE BAR] and then [ENTER] to select Yes or No This field is N/A when you choose DDNS client as your service provider. WWW.DynDNS.ORG (default) Yes me.dyndns.org mail@mailserver No When you have completed this menu, press [ENTER] at the prompt “Press ENTER to Confirm…” to save your configuration, or press [ESC] at any time to cancel. If you have a private WAN IP address, then you cannot use Dynamic DNS. 2.12 LAN Setup This section describes how to configure the Ethernet using Menu 3 — LAN Setup. From the main menu, enter 3 to display menu 3. Settings configured in Menu 3 — LAN Setup apply to the LAN side of the router only. 2-16 Hardware Installation and Initial Setup Prestige 650 ADSL Router Menu 3 - LAN Setup 1. LAN Port Filter Setup 2. TCP/IP and DHCP Setup Enter Menu Selection Number: Figure 2-13 Menu 3 — LAN Setup 2.12.1 LAN Port Filter Setup This menu allows you to specify filter set(s) that you wish to apply to the Ethernet traffic. You seldom need to filter Ethernet traffic; however, the filter sets may be useful to block certain packets, reduce traffic and prevent security breaches. Menu 3.1 - LAN Port Filter Setup Input Filter Sets: protocol filters= device filters= Output Filter Sets: protocol filters= device filters= Press ENTER to Confirm or ESC to Cancel: Figure 2-14 Menu 3.1 — General Ethernet Setup If you need to define filters, please read the Filter Set Configuration chapter first, then return to this menu to define the filter sets. 2.13 Protocol Dependent Ethernet Setup Depending on the protocols for your applications, you need to configure the respective Ethernet Setup, as outlined next. For TCP/IP Ethernet setup refer to Internet Access Application. For bridging Ethernet setup refer to Bridging Setup. Hardware Installation and Initial Setup 2-17 Prestige 650 ADSL Router Chapter 3 Internet Access This chapter shows you how to configure the LAN and WAN of your Prestige for Internet access. 3.1 Factory Ethernet Defaults The Ethernet parameters of the Prestige are preset in the factory with the following values: 1. IP address of 192.168.1.1 with subnet mask of 255.255.255.0 (24 bits). 2. DHCP server enabled with 32 client IP addresses starting from 192.168.1.33. These parameters should work for the majority of installations. If the parameters are satisfactory, you can skip to TCP/IP Ethernet Setup and DHCP to enter the DNS server address(es) if your ISP gives you explicit DNS server address(es). If you wish to change the factory defaults or to learn more about TCP/IP, please read on. 3.2 LANs and WANs A LAN (Local Area Network) is a computer network limited to the immediate area, usually the same building or floor of a building. A WAN (Wide Area Network), on the other hand, is an outside connection to another network or the Internet. 3.2.1 LANs, WANs and the Prestige The actual physical connection determines whether the Prestige ports are LAN or WAN ports. There are two separate IP networks, one inside, the LAN network; the other outside: the WAN network as shown next: Internet Access 3-1 Prestige 650 ADSL Router Figure 3-1 LAN & WAN IPs 3.3 TCP/IP Parameters 3.3.1 IP Address and Subnet Mask Like houses on a street that share a common street name, the computers on a LAN share one common network number. Where you obtain your network number depends on your particular situation. If the ISP or your network administrator assigns you a block of registered IP addresses, follow their instructions in selecting the IP addresses and the subnet mask. If the ISP did not explicitly give you an IP network number, then most likely you have a single user account and the ISP will assign you a dynamic IP address when the connection is established. If this is the case, it is recommended that you select a network number from 192.168.0.0 to 192.168.255.0 (ignoring the trailing zero) and you must enable the Single User Account feature of the Prestige. The Internet Assigned Number Authority (IANA) reserved this block of addresses specifically for private use; please do not use any other number unless you are told otherwise. Let’s say you select 192.168.1.0 as the network number; which covers 254 individual addresses, from 192.168.1.1 to 192.168.1.254 (zero and 255 are reserved). In other words, the first three numbers specify the network number while the last number identifies an individual computer on that network. The subnet mask specifies the network number portion of an IP address. Your Prestige will compute the subnet mask automatically based on the IP address that you entered. You don’t need to change the subnet mask computed by the Prestige unless you are instructed to do otherwise. 3-2 Internet Access Prestige 650 ADSL Router 3.3.2 Private IP Addresses Every machine on the Internet must have a unique address. If your networks are isolated from the Internet, for example, only between your two branch offices, you can assign any IP addresses to the hosts without problems. However, the Internet Assigned Numbers Authority (IANA) has reserved the following three blocks of IP addresses specifically for private networks: 10.0.0.0 — 10.255.255.255 172.16.0.0 — 172.31.255.255 192.168.0.0 — 192.168.255.255 You can obtain your IP address from the IANA, from an ISP or it can be assigned from a private network. If you belong to a small organization and your Internet access is through an ISP, the ISP can provide you with the Internet addresses for your local networks. On the other hand, if you are part of a much larger organization, you should consult your network administrator for the appropriate IP addresses. Note: Regardless of your particular situation, do not create an arbitrary IP address; always follow the guidelines above. For more information on address assignment, please refer to RFC 1597, Address Allocation for Private Internets and RFC 1466, Guidelines for Management of IP Address Space. 3.3.3 RIP Setup RIP (Routing Information Protocol) allows a router to exchange routing information with other routers. The RIP Direction field controls the sending and receiving of RIP packets. When set to: 1. Both - the Prestige will broadcast its routing table periodically and incorporate the RIP information that it receives. 2. In Only - the Prestige will not send any RIP packets but will accept all RIP packets received. 3. Out Only - the Prestige will send out RIP packets but will not accept any RIP packets received. 4. None - the Prestige will not send any RIP packets and will ignore any RIP packets received. The Version field controls the format and the broadcasting method of the RIP packets that the Prestige sends (it recognizes both formats when receiving). RIP-1 is universally supported; but RIP-2 carries more information. RIP-1 is probably adequate for most networks, unless you have an unusual network topology. Both RIP-2B and RIP-2M sends the routing data in RIP-2 format; the difference being that RIP-2B uses subnet broadcasting while RIP-2M uses multicasting. Internet Access 3-3 Prestige 650 ADSL Router 3.3.4 DHCP Configuration DHCP (Dynamic Host Configuration Protocol) allows the individual clients (computers) to obtain the TCP/IP configuration at start-up from a centralized DHCP server. The Prestige has built-in DHCP server capability, enabled by default, which means it can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. The Prestige can also act as a surrogate DHCP server where it relays IP address assignment from the actual DHCP server to the clients. IP Pool Setup The Prestige is pre-configured with a pool of 32 IP addresses starting from 192.168.1.33 to 192.168.1.64 for the client machines. This leaves 31 IP addresses, 192.168.1.2 to 192.168.1.32 (excluding the Prestige itself which has a default IP of 192.168.1.1) for other server machines, for example, server for mail, FTP, telnet, web, etc., that you may have. DNS Server Address DNS (Domain Name System) is for mapping a domain name to its corresponding IP address and vice versa, for example, the IP address of www.zyxel.com is 204.217.0.2. The DNS server is extremely important because without it, you must know the IP address of a machine before you can access it. The DNS server addresses that you enter in the DHCP setup are passed to the client machines along with the assigned IP address and subnet mask. There are two ways that an ISP disseminates the DNS server addresses. The first is for an ISP to tell a customer the DNS server addresses, usually in the form of an information sheet, when s/he signs up. If your ISP does give you the DNS server addresses, enter them in the DNS Server fields in DHCP Setup, otherwise, leave them blank. Some ISP’s choose to pass the DNS servers using the DNS server extensions of PPP IPCP (IP Control Protocol) after the connection is up. If your ISP did not give you explicit DNS servers, chances are the DNS servers are conveyed through IPCP negotiation. The Prestige supports the IPCP DNS server extensions through the DNS proxy feature. If the Primary and Secondary DNS Server fields in DHCP Setup are not specified, for instance, left as 0.0.0.0, the Prestige tells the DHCP clients that it itself is the DNS server. When a computer sends a DNS query to the Prestige, the Prestige forwards the query to the real DNS server learned through IPCP and relays the response back to the computer. Please note that DNS proxy works only when the ISP uses the IPCP DNS server extensions. It does not mean you can leave the DNS servers out of the DHCP setup under all circumstances. If your ISP gives you explicit DNS servers, make sure that you enter their IP addresses in the DHCP Setup menu. This way, the Prestige can pass the DNS servers to the computers and the computers can query the DNS server directly without the Prestige’s intervention. 3-4 Internet Access Prestige 650 ADSL Router 3.4 IP Multicast Traditionally, IP packets are transmitted in one of either two ways - Unicast (1 sender – 1 recipient) or Broadcast (1 sender – everybody on the network). Multicast is a third way to deliver IP packets to a group of hosts on the network - not everybody. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group - it is not used to carry user data. IGMP version 2 (RFC 2236) is an improvement over version 1 (RFC 1112) but IGMP version 1 is still in wide use. If you would like to read more detailed information about interoperability between IGMP version 2 and version 1, please see sections 4 and 5 of RFC 2236. The class D IP address is used to identify host groups and can be in the range 224.0.0.0 to 239.255.255.255. The address 224.0.0.0 is not assigned to any group and is used by IP multicast computers. The address 224.0.0.1 is used for query messages and is assigned to the permanent group of all IP hosts (including gateways). All hosts must join the 224.0.0.1 group in order to participate in IGMP. The address 224.0.0.2 is assigned to the multicast routers group. The Prestige supports both IGMP version 1 (IGMP-v1) and version 2 (IGMP-v2). At start up, the Prestige queries all directly connected networks to gather group membership. After that, the Prestige periodically updates this information. IP Multicasting can be enabled/disabled on the Prestige LAN and/or WAN interfaces using menus 3.2 (LAN) and 11.3 (WAN). Select None to disable IP Multicasting on these interfaces. 3.5 IP Policies Traditionally, routing is based on the destination address only and the router takes the shortest path to forward a packet. IP Policy Routing (IPPR) provides a mechanism to override the default routing behavior and alter the packet forwarding based on the policy defined by the network administrator. Policy-based routing is applied to incoming packets on a per interface basis, prior to the normal routing. Create policies using SMT menu 25 (see IP Policy Routing) and apply them on the Prestige LAN and/or WAN interfaces using menus 3.2 (LAN) and 11.3 (WAN). 3.6 IP Alias IP Alias allows you to partition a physical network into different logical networks over the same Ethernet interface. The Prestige supports three logical LAN interfaces via its single physical Ethernet interface with the Prestige itself as the gateway for each LAN network. Internet Access 3-5 Prestige 650 ADSL Router Figure 3-2 Physical Network Figure 3-3 Partitioned Logical Networks Use menu 3.2.1 to configure IP Alias on your Prestige. 3.6.1 IP Alias Setup Use menu 3.2 to configure the first network. Move the cursor to Edit IP Alias field and press [SPACEBAR] to choose Yes and press [ENTER] to configure the second and third network. Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup: DHCP= Server Client IP Pool Starting Addres= 192.168.1.33 Size of Client IP Pool= 6 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= None Version= N/A Multicast= None IP Policies= Edit IP Alias= No Press ENTER to confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 3-4 Menu 3.2 — TCP/IP and DHCP Ethernet Setup 3-6 Internet Access Prestige 650 ADSL Router Pressing [ENTER] displays Menu 3.2.1 — IP Alias Setup, as shown next. Menu 3.2.1 - IP Alias Setup IP Alias 1= No IP Address= N/A IP Subnet Mask= N/A RIP Direction= N/A Version= N/A Incoming protocol filters= Outgoing protocol filters= IP Alias 2= No IP Address= N/A IP Subnet Mask= N/A RIP Direction= N/A Version= N/A Incoming protocol filters= Outgoing protocol filters= N/A N/A N/A N/A Enter here to CONFIRM or ESC to CANCEL: Press Space Bar to Toggle. Figure 3-5 Menu 3.2.1 — IP Alias Setup Follow the instructions in the following table to configure IP Alias parameters. Table 3-1 IP Alias Setup Menu Fields FIELD DESCRIPTION IP Alias Choose Yes to configure the LAN network for the Prestige. IP Address Enter the IP address of your Prestige in dotted decimal notation IP Subnet Mask Your Prestige will automatically calculate the subnet mask based on the IP address that you assign. Unless you are implementing subnetting, use the subnet mask computed by the Prestige EXAMPLE Yes 192.168.2.1 255.255.255.0 RIP Direction Press [SPACE BAR] to select the RIP direction. Choices are None, Both, In Only or Out Only. None Version Press [SPACE BAR] to select the RIP version. Choices are RIP-1, RIP-2B or RIP-2M. RIP-1 Incoming Enter the filter set(s) you wish to apply to the incoming traffic Protocol Filters between this node and the Prestige. Outgoing Enter the filter set(s) you wish to apply to the outgoing traffic between Protocol Filters this node and the Prestige. When you have completed this menu, press [ENTER] at the prompt “Press ENTER to Confirm…” to save your configuration, or press [ESC] at any time to cancel. Internet Access 3-7 Prestige 650 ADSL Router 3.7 Route IP Setup The first step is to enable the IP routing in Menu 1 — General Setup. To edit menu 1, type in 1 in the main menu and press [ENTER]. Set the Route IP field to Yes by pressing [SPACE BAR]. Menu 1 - General Setup System Name= P650R Location= location Contact Person's Name= Domain Name= Edit Dynamic DNS= No Route IP= Yes Bridge= No Press ENTER to Confirm or ESC to Cancel: Figure 3-6 Menu 1 — General Setup 3.8 TCP/IP Ethernet Setup and DHCP Use menu 3.2 to configure your Prestige for TCP/IP. To edit menu 3.2, enter 3 from the main menu to display Menu 3 — Ethernet Setup. When menu 3 appears, press 2 and press [ENTER] to display Menu 3.2 — TCP/IP and DHCP Ethernet Setup, as shown next: 3-8 Internet Access Prestige 650 ADSL Router Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup: DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 6 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.68.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-1 Multicast= None IP Policies= Edit IP Alias= No First address in the IP Pool Size of the IP Pool IP addresses of the DNS servers Press ENTER to Confirm or ESC to Cancel: This is the IP address of the Prestige Press Space Bar to Toggle. Figure 3-7 Menu 3.2 — TCP/IP and DHCP Ethernet Setup Follow the instructions in the following table on how to configure the DHCP fields. Table 3-2 DHCP Ethernet Setup Menu Fields FIELD DESCRIPTION EXAMPLE DHCP Setup DHCP If set to Server, your Prestige can assign IP addresses, an IP default gateway and DNS servers to Windows 95, Windows NT and other systems that support the DHCP client. If set to None, the DHCP server will be disabled. If set to Relay, the Prestige acts as a surrogate DHCP server and relays DHCP requests and responses between the remote server and the clients. Enter the IP address of the actual, remote DHCP server in the Remote DHCP Server in this case. Server (default) When DHCP is used, the following items need to be set: Client IP Pool Starting This field specifies the first of the contiguous addresses in the IP Address address pool. Size of Client IP Pool This field specifies the size or count of the IP address pool. 192.168.1.33 32 Primary DNS Server Enter the IP addresses of the DNS servers. The DNS servers are passed to the DHCP clients along with the IP address and Secondary DNS Server the subnet mask. Internet Access 3-9 Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE Remote DHCP Server If Relay is selected in the DHCP field above then enter the IP address of the actual remote DHCP server here. Follow the instructions in the following table to configure TCP/IP parameters for the Ethernet port. Table 3-3 TCP/IP Ethernet Setup Menu Fields FIELD DESCRIPTION EXAMPLE TCP/IP Setup IP Address Enter the (LAN) IP address of your Prestige in dotted decimal notation IP Subnet Mask Your Prestige will automatically calculate the subnet mask based on the IP address that you assign. Unless you are implementing subnetting, use the subnet mask computed by the Prestige. RIP Direction Press [SPACE BAR] to select the RIP direction. Choices are Both, In Only, Out Only or None. 192.168.1.1 255.255.255.0 Both (default) Version Press [SPACE BAR] to select the RIP version. Choices are RIP-1, RIP-2B or RIP-2M. RIP-1 (default) Multicast IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a Multicast group. The Prestige supports both IGMP version 1 (IGMP-v1) and version 2 ( IGMP-v2). Press the [SPACE BAR] to enable IP Multicasting or select None to disable it. None (default) IP Policies Create policies using SMT menu 25 (see the IP Policy Routing chapter) and apply them on the Prestige LAN interface here. You can apply up to four IP Policy sets (from twelve) by entering their numbers separated by commas. 2,4,7,9 Edit IP Alias The Prestige supports three logical LAN interfaces via its single physical Ethernet interface with the Prestige itself as the gateway for each LAN network. Press [SPACE BAR] to change No to Yes and press [ENTER] to for menu 3.2.1 No (default) When you have completed this menu, press [ENTER] at the prompt “Press ENTER to Confirm…” to save your configuration, or press [ESC] at any time to cancel. 3-10 Internet Access Prestige 650 ADSL Router 3.9 VPI and VCI Be sure to use the correct Virtual Path Identifier (VPI) and Virtual Channel Identifier (VCI) numbers supplied by your telephone company. The valid range for the VPI is 0 to 255 and for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). Please see the Appendices for more information. 3.10 Multiplexing There are two conventions to identify what protocols the virtual circuit (VC) is carrying. Be sure to use the multiplexing method required by your ISP. 3.10.1 VC-based Multiplexing In this case, by prior mutual agreement, each protocol is assigned to a specific virtual circuit, for example, VC1 carries IP, etc. VC-based multiplexing may be dominant in environments where dynamic creation of large numbers of ATM VCs is fast and economical. 3.10.2 LLC-based Multiplexing In this case one VC carries multiple protocols with protocol identifying information being contained in each packet header. Despite the extra bandwidth and processing overhead, this method may be advantageous if it is not practical to have a separate VC for each carried protocol, for example, if charging heavily depends on the number of simultaneous VCs. 3.11 Encapsulation Be sure to use the encapsulation method required by your ISP. The Prestige supports the following methods. 3.11.1 ENET ENCAP The MAC Encapsulated Routing Link Protocol (ENET ENCAP) is only implemented with the IP network protocol. IP packets are routed between the Ethernet interface and the WAN interface and then formatted so that they can be understood in a bridged environment for instance, it encapsulates routed Ethernet frames into bridged ATM cells. ENET ENCAP requires that you specify a gateway IP address in the Ethernet Encapsulation Gateway field in menu 4 and in the Rem IP Addr field in menu 11.1. You can get this information from your ISP. Internet Access 3-11 Prestige 650 ADSL Router 3.11.2 PPP over Ethernet PPPoE provides access control and billing functionality in a manner similar to dial-up services using PPP. The Prestige bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your computer to an ATM PVC (Permanent Virtual Circuit) which connects to a xDSL Access Concentrator where the PPP session terminates. One PVC can support any number of PPP sessions from your LAN. For more information on PPPoE, see the Appendices. 3.11.3 PPPoA Please refer to RFC 2364 for more information on PPP over ATM Adaptation Layer 5 (AAL5). Refer to RFC 1661 for more information on PPP. 3.11.4 RFC 1483 RFC 1483 describes two methods for Multiprotocol Encapsulation over ATM Adaptation Layer 5 (AAL5). The first method allows multiplexing of multiple protocols over a single ATM virtual circuit (LLC-based multiplexing) and the second method assumes that each protocol is carried over a separate ATM virtual circuit (VC-based multiplexing). Please refer to the RFC for more detailed information. 3.12 IP Address Assignment A static IP is a fixed IP that your ISP gives you. A dynamic IP is not fixed; the ISP assigns you a different one each time. The Single User Account feature can be enabled or disabled if you have either a dynamic or static IP. However the encapsulation method assigned influences your choices for IP Address and ENET ENCAP Gateway. 3.12.1 Using PPPoA or PPPoE Encapsulation If you have a dynamic IP, then the IP Address and ENET ENCAP Gateway fields are not applicable (N/A). If you have a static IP, then you only need to fill in the IP Address field and not the ENET ENCAP Gateway field. 3.12.2 Using RFC 1483 Encapsulation In this case the IP Address Assignment must be static with the same requirements for the IP Address and ENET ENCAP Gateway fields as stated above. 3.12.3 Using ENET ENCAP Encapsulation In this case you can have either a static or dynamic IP. For a static IP you must fill in all the IP Address and ENET ENCAP Gateway fields as supplied by your ISP. However for a dynamic IP, the Prestige acts as a 3-12 Internet Access Prestige 650 ADSL Router DHCP client on the WAN port and so the IP Address and ENET ENCAP Gateway fields are not applicable (N/A) as they are assigned to the Prestige by the DHCP server. 3.13 Internet Access Configuration Menu 4 allows you to enter the Internet Access information in one screen. Menu 4 is actually a simplified setup for one of the remote nodes that you can access in menu 11. Before you configure your Prestige for Internet access, you need to collect your Internet account information from your ISP and telephone company. Use the following table to record your Internet Account Information. Note that if you are using PPPoA or PPPoE encapsulation, then the only ISP information you need is a login name and password. You only need to know the Ethernet Encapsulation Gateway IP address if you are using ENET ENCAP encapsulation. Table 3-4 Internet Account Information FIELD DESCRIPTION System Name Name of the Prestige (optional). Encapsulation PPPoE, RFC1483, PPPoA or ENET ENCAP. Multiplexing LLC-based or VC-based. If this information is not given, use the default. VPI Enter your Virtual Path Identifier here. VCI Enter your Virtual Channel Identifier here. My Login Enter the login name assigned by your ISP (for PPPoA/PPPoE only). My Password Enter the password associated with your ISP assigned My Login (for PPPoA/PPPoE only). Idle Timeout (PPPoE or PPP) Enter the time lapse, in seconds, before you automatically disconnect from the PPPoE or PPPoA server. IP Address Enter if your IP address if it is not dynamically assigned. Network Address Translation Full Feature, SUA Only or None. ENET ENCAP Gateway IP Address Gateway IP Address Enter when using ENET ENCAP Encapsulation. Internet Access YOUR INFO 3-13 Prestige 650 ADSL Router 3.13.1 Traffic Shaping Traffic Shaping is an agreement between the carrier and the subscriber to regulate the average rate and “burstiness” or fluctuation of data transmission over an ATM network. This agreement helps eliminate congestion, which is important for transmission of real time data such as audio and video connections. Peak Cell Rate (PCR) is the maximum rate at which the sender can send cells. This parameter may be lower (but not higher) than the maximum line speed. 1 ATM cell is 53 bytes (424 bits), so a maximum speed of 832 Kbps gives a maximum PCR of 1962 cells/sec. This rate is not guaranteed because it is dependent on the line speed. Sustained Cell Rate (SCR) is the mean cell rate of a bursty, on-off traffic source that can be sent at the peak rate, and a parameter for burst-type traffic. SCR may not be greater than the PCR; the system default is 0 cells/sec. Maximum Burst Size (MBS) is the maximum number of cells that can be sent at the PCR. After MBS is reached, cell rates fall below SCR until cell rate averages to the SCR again. At this time, more cells (up to the MBS) can be sent at the PCR again. If the PCR, SCR or MBS is set to the default of “0”, the system will assign a maximum value that correlates to your upstream line rate. The following figure illustrates the relationship between PCR, SCR and MBS. Figure 3-8 Example of Traffic Shaping From the main menu, type 4 to display Menu 4 — Internet Access Setup, as shown next. 3-14 Internet Access Prestige 650 ADSL Router Menu 4 - Internet Access Setup ISP's Name= MyISP Encapsulation= RFC 1483 Multiplexing= VC-based VPI #= 8 VCI #= 35 ATM QoS Type= CBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static IP Address= 0.0.0.0 Network Address Translation= SUA Only Address Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: Figure 3-9 Internet Access Setup The following table contains instructions on how to configure your Prestige for Internet access. Table 3-5 Internet Access Setup Menu Fields FIELD DESCRIPTION EXAMPLE ISP’s Name Enter the name of your Internet Service Provider. This information is for identification purposes only. Encapsulation Press [SPACE BAR] to select the method of encapsulation used by your ISP. Choices are PPPoE, PPP, RFC 1483 or ENET ENCAP. RFC 1483 Multiplexing Press [SPACE BAR] to select the method of multiplexing used by your ISP. Choices are VC-based or LLC-based. VC-based VPI # Enter the Virtual Path Identifier (VPI) that the telephone company gives you. 8 VCI # Enter the Virtual Channel Identifier (VCI) that the telephone company gives you. 35 ATM QoS Type Press [SPACE BAR] and select CBR (Continuous Bit Rate) to specify fixed (always-on) bandwidth. Select UBR (Unspecified Bit Rate) for applications that are non-time sensitive, such as e-mail. UBR Peak Cell Rate (PCR) This is the maximum rate at which the sender can send cells. Type the PCR. 0 Internet Access MyISP 3-15 Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE Sustained Cell Rate is the mean cell rate of a bursty, on-off traffic source that can be sent at the peak rate, and a parameter for burst-type traffic. Type the SCR; it must be less than the PCR. 0 Refers to the maximum number of cells that can be sent at the peak rate. Type the MBS. The MBS must be less than 65535. 0 My Login Configure the My Login and My Password fields for PPPoA and PPPoE encapsulation only. Enter the login name that your ISP gives you. If you are using PPPoE encapsulation, then this field must be of the form user@domain where domain identifies your PPPoE service name. N/A My Password Enter the password associated with the login name above. N/A ENET ENCAP Gateway Enter the gateway IP address supplied by your ISP when you are using ENET ENCAP encapsulation. N/A Idle Timeout This value specifies the number of idle seconds that elapse before the Prestige automatically disconnects the PPPoE session. 100 (default) IP Address Assignment Press [SPACE BAR] to select Static or Dynamic address assignment. Static Enter the IP address supplied by your ISP if applicable. 0.0.0.0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 IP Address Network Address Translation Press [SPACE BAR] to select None, SUA Only or Full Feature. Please see the NAT Chapter for more details on the SUA (Single User Account) feature. SUA Only Address Mapping Set Type the numbers of mapping sets (1-8) to use with NAT. See the NAT chapter for details. N/A When you have completed this menu, press [ENTER] at the prompt “Press ENTER to Confirm…” to save your configuration, or press [ESC] at any time to cancel. If all your settings are correct your Prestige should connect automatically to the Internet. If the connection fails, note the error message that you receive on the screen and take the appropriate troubleshooting steps. 3-16 Internet Access Advanced Applications Part II: ADVANCED APPLICATIONS This part shows how to configure Remote Node, Remote Node TCP/IP and NAT. II Prestige 650 ADSL Router Chapter 4 Remote Node Configuration This chapter covers the parameters that are protocol-independent. Protocol-dependent configuration (TCP/IP and Bridging) is covered in the following chapters. A remote node is required for placing calls to a remote gateway. A remote node represents both the remote gateway and the network behind it across a WAN connection. When you use menu 4 to set up Internet access, you are configuring one of the remote nodes. 4.1 Remote Node Setup This section describes the protocol-independent parameters for a remote node. 4.1.1 Remote Node Profile To configure a remote node, follow these steps: Step 1. From the main menu, enter 11 to display Menu 11 - Remote Node Setup. Step 2. When menu 11 appears, as shown in the following figure, type the number of the remote node that you want to configure. Remote Node Configuration 4-1 Prestige 650 ADSL Router Menu 11 - Remote Node Setup 1. 2. 3. 4. 5. 6. 7. 8. My ISP (ISP, SUA) ________ ________ ________ ________ ________ ________ ________ Enter Node # to Edit: Figure 4-1 Menu 11 — Remote Node Setup 4.1.2 Encapsulation and Multiplexing Scenarios For Internet access you should use the encapsulation and multiplexing methods used by your ISP. For LAN-to-LAN applications, for example, between a branch office and corporate headquarters, prior agreement on methods is necessary because encapsulation and multiplexing cannot be automatically determined. What method(s) you use depends on how many VCs you have and how many different network protocols you need. The extra overhead that ENET ENCAP encapsulation entails makes it a poor choice in a LAN-to-LAN application. Here are some examples of more suitable combinations in such an application. Scenario 1. One VC, Multiple Protocols PPPoA (RFC-2364) encapsulation with VC-based multiplexing is the best combination because no extra protocol identifying headers are needed. The PPPoA protocol already contains this information. Scenario 2. One VC, One Protocol (IP) Selecting RFC-1483 encapsulation with VC-based multiplexing requires the least amount of overhead (0 octets). However, if there is a potential need for multiple protocol support in the future, it may be safer to select PPPoA encapsulation instead of RFC-1483, so you do not need to reconfigure either computer later. Scenario 3. Multiple VCs If you have an equal number (or more) of VCs than the number of protocols, then select RFC-1483 encapsulation and VC-based multiplexing. 4-2 Remote Node Configuration Prestige 650 ADSL Router Nailed-Up Connection (PPPoA/PPPoE) A nailed-up connection is a dial-up line where the connection is always up regardless of traffic demand. The Prestige does two things when you specify a nailed-up connection. The first is that idle timeout is disabled. The second is that the Prestige will try to bring up the connection when turned on and whenever the connection is down. A nailed-up connection can be very expensive for obvious reasons. Do not specify a nailed-up connection unless your telephone company offers flat-rate service or you need a constant connection and the cost is of no concern. Menu 11.1 - Remote Node Profile Rem Node Name= myISP Active= Yes Route= IP Bridge= No Encapsulation= PPPoE Multiplexing= LLC-based Service Name= any Incoming: Rem Login= Rem Password= ******** Outgoing: My Login= My Password= ******** Authen= CHAP/PAP Edit IP/Bridge= No Edit ATM Options= No Telco Option: Allocated Budget(min)= 0 Period (hr)= 0 Schedule Sets= Nailed-Up Connection= No Session Options: Edit Filter Sets= No Idle Timeout (sec)= 0 Press ENTER to Confirm or ESC to Cancel: Figure 4-2 Menu 11.1 — Remote Node Profile In Menu 11.1 — Remote Node Profile, fill in the fields as described in the following table. Table 4-1 Remote Node Profile Menu Fields FIELD DESCRIPTION Rem Node Name Type a unique, descriptive name of up to eight characters for this node. Active Press [SPACE BAR] and then [ENTER] to select Yes to activate or No to deactivate this node. Inactive nodes are displayed with a minus sign “–“ in SMT menu 11. Remote Node Configuration EXAMPLE myISP Yes 4-3 Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE Encapsulation PPPoE (Point-to-Point Protocol over Ethernet). PPPoA refers to RFC-2364 (PPP Encapsulation over ATM Adaptation Layer 5). If RFC-1483 (Multiprotocol Encapsulation over ATM Adaptation Layer 5) of ENET ENCAP are selected, then the Rem Login, Rem Password, My Login, My Password, Edit PPP Options and Authen fields are not applicable (N/A). PPPoE Multiplexing Press [SPACE BAR] and then [ENTER] to select the method of multiplexing that your ISP uses, either VCbased or LLC-based. Service Name When using PPPoE encapsulation, type the name of your PPPoE service here. Incoming: Type the login name that this remote node will use to call your Prestige. The login name and the Rem Password will be used to authenticate this node. Rem Login Rem Password LLC-based Type the password used when this remote node calls your Prestige. Outgoing: My Login My Password Authen Type the login name assigned by your ISP when the Prestige calls this remote node. Type the password assigned by your ISP when the Prestige calls this remote node. This field sets the authentication protocol used for outgoing calls. Options for this field are: CHAP/PAP – Your Prestige will accept either CHAP or PAP when requested by this remote node. CHAP – accept CHAP (Challenge Handshake Authentication Protocol) only. CHAP/PAP PAP – accept PAP (Password Authentication Protocol) only. Route This field determines the protocol used in routing. Options are IP and None. IP Bridge When bridging is enabled, your Prestige will forward any packet that it does not route to this remote node; otherwise, the packets are discarded. Select Yes to enable and No to disable. No 4-4 Remote Node Configuration Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE Edit IP/Bridge Press [SPACE BAR] to select Yes and press [ENTER] to display Menu 11.3 – Remote Node Network Layer Options. No Edit ATM Options Press [SPACE BAR] to select Yes and press [ENTER] to display Menu 11.6 – Remote Node ATM Layer Options. No Telco Option This sets a ceiling for outgoing call time for this remote node. The default for this field is 0 meaning no budget control. 0 (default) Period (hr) This field is the time period that the budget should be reset. For example, if we are allowed to call this remote node for a maximum of 10 minutes every hour, then the Allocated Budget is (10 minutes) and the Period (hr) is 1 (hour). 0 (default) Schedule Sets This field is only applicable for PPPoE or PPPoA encapsulation. You can apply up to four schedule sets here. For more details please refer to the Call Schedule Setup chapter. Allocated Budget (min) Nailed up Connection Session Options Edit Filter Sets Idle Timeout (sec) This field is only applicable for PPPoE or PPPoA encapsulation. This field specifies if you want to make the connection to this remote node a nailed-up connection. More details are given earlier in this section. No Use [SPACE BAR] to choose Yes and press [ENTER] to open menu 11.5 to edit the filter sets. See the Remote Node Filter section for more details. No (default) Type the number of seconds (0-9999) that can elapse when the Prestige is idle (there is no traffic going to the remote node), before the Prestige automatically disconnects the remote node. 0 means that the session will not timeout. 0 (default) When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. 4.1.3 Outgoing Authentication Protocol For obvious reasons, you should employ the strongest authentication protocol possible. However, some vendors’ implementation includes specific authentication protocol in the user profile. It will disconnect if Remote Node Configuration 4-5 Prestige 650 ADSL Router the negotiated protocol is different from that in the user profile, even when the negotiated protocol is stronger than specified. If the peer disconnects right after a successful authentication, make sure that you specify the correct authentication protocol when connecting to such an implementation. 4.2 Remote Node Setup For the TCP/IP parameters, perform the following steps to edit Menu 11.3 – Remote Node Network Layer Options as shown next. Step 1. In menu 11.1, make sure IP is among the protocols in the Route field. Step 2. Move the cursor to the Edit IP/Bridge field, press [SPACE BAR] to select Yes, then press [ENTER] to display Menu 11.3 – Remote Node Network Layer Options. Figure 4-3 Remote Node Network Layer Options The next table explains fields in Menu 11.3 – Remote Node Network Layer Options. Table 4-2 Remote Node Network Layer Options FIELD IP Address A i t 4-6 DESCRIPTION EXAMPLE Press [SPACE BAR] and then [ENTER] to select Dynamic if the remote d i i d i ll i d IP dd St ti if it i i Static Remote Node Configuration Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE IP Address Assignment Press [SPACE BAR] and then [ENTER] to select Dynamic if the remote node is using a dynamically assigned IP address or Static if it is using a static (fixed) IP address. You will only be able to configure this in the ISP node (also the one you configure in menu 4), all other nodes are set to Static. Static Rem IP Addr This is the IP address you entered in the previous menu. Rem Subnet Mask Type the subnet mask assigned to the remote node. My WAN Addr Some implementations, especially UNIX derivatives, require separate IP network numbers for the WAN and LAN links and each end to have a unique address within the WAN network number. In that case, type the IP address assigned to the WAN port of your Prestige. NOTE: Refers to local Prestige address, not the remote router address. NAT Press [SPACE BAR] and then [ENTER] to select Full Feature if you have multiple public WAN IP addresses for your Prestige. Full Feature Select SUA Only if you have just one public WAN IP address for your Prestige. The SMT uses Address Mapping Set 255 (menu 15.1 - see section 7.3.1). Select None to disable NAT. Address Mapping Set When Full Feature is selected in the NAT field, configure address mapping sets in menu 15.1. Select one of the NAT server sets (2-10) in menu 15.2 (see the NAT chapter for details) and type that number here. 2 When SUA Only is selected in the NAT field, the SMT uses NAT server set 1 in menu 15.2 (see the NAT chapter for details). Metric The metric represents the “cost” of transmission for routing purposes. IP routing uses hop count as the cost measurement, with a minimum of 1 for directly connected networks. Type a number that approximates the cost for this link. The number need not be precise, but it must be between 1 and 15. In practice, 2 or 3 is usually a good number. 2 Private This determines if the Prestige will include the route to this remote node in its RIP broadcasts. If set to Yes, this route is kept private and not included in RIP broadcast. If No, the route to this remote node will be propagated to other hosts through RIP broadcasts. No RIP Direction Press [SPACE BAR] and then [ENTER] to select the RIP Direction. Options are Both, In Only, Out Only or None. Remote Node Configuration None 4-7 Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE Press [SPACE BAR] and then [ENTER] to select the RIP version. Options are RIP-1, RIP-2B or RIP-2M. RIP-1 Multicast IGMP-v1 sets IGMP to version 1, IGMP-v2 sets IGMP to version 2 and None disables IGMP. None IP Policies You can apply up to four IP Policy sets (from 12) by typing in their numbers separated by commas. Configure the filter sets in menu 25 first (see the IP Policy Routing chapter) and then apply them here. Version 3, 4, 5, 6 When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. 4.3 Remote Node Filter Move the cursor to the Edit Filter Sets field in menu 11.1, then press [SPACE BAR] to select Yes. Press [ENTER] to display Menu 11.5 – Remote Node Filter. Use Menu 11.5 – Remote Node Filter to specify the filter set(s) to apply to the incoming and outgoing traffic between this remote node and the Prestige and also to prevent certain packets from triggering calls. You can specify up to 4 filter sets separated by comma, for example, 1, 5, 9, 12, in each filter field. Note that spaces are accepted in this field. The Prestige has a prepackaged filter set, NetBIOS_WAN, that blocks NetBIOS packets (call protocol filter = 1). Include this in the call filter sets if you want to prevent NetBIOS packets from triggering calls to a remote node. Menu 11.5 - Remote Node Filter Input Filter Sets: protocol filters= device filters= Output Filter Sets: protocol filters= device filters= Call Filter Sets: protocol filters= device filters= Figure 4-4 Menu 11.5 — Remote Node Filter Note that call filter sets are visible when you select PPPoA or PPPoE encapsulation. 4-8 Remote Node Configuration Prestige 650 ADSL Router Chapter 5 Remote Node TCP/IP Configuration This chapter shows a sample LAN-to-LAN application and how to configure TCP/IP remote node. 5.1 TCP/IP Configuration The following sections describe how to configure the TCP/IP parameters of a remote node. 5.1.1 Editing TCP/IP Options Follow the steps shown next to edit Menu 11.6 – Remote Node ATM Layer Options. In menu 11.1, move the cursor to the Edit ATM Options field and then press [SPACE BAR] to select Yes. Press [ENTER] to display Menu 11.6 – Remote Node ATM Layer Options. There are two versions of menu 11.6 for the Prestige, depending on whether you chose VC-based/LLCbased multiplexing and PPPoA encapsulation in menu 11.1. VC-based Multiplexing For VC-based multiplexing, by prior agreement, a protocol is assigned a specific virtual circuit, for example, VC1 will carry IP. Separate VPI and VCI numbers must be specified for each protocol. Remote Node TCP/IP Configuration 5-1 Prestige 650 ADSL Router Menu 11.6 - Remote Node ATM Layer Options VPI/VCI (VC-Multiplexing) VC Options for IP: VPI #= 0 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 VC Options for Bridge: VPI #= 1 VCI #= 36 ATM QoS Type= N/A Peak Cell Rate (PCR)= N/A Sustain Cell Rate (SCR)= N/A Maximum Burst Size (MBR)= N/A Separate VPI and VCI numbers must be specified Press ENTER to Confirm or ESC to Cancel: Figure 5-1 Menu 11.6 for VC-based Multiplexing LLC-based Multiplexing or PPPoA Encapsulation For LLC-based multiplexing or PPPoA encapsulation, one VC carries multiple protocols with protocol identifying information being contained in each packet header. Menu 11.6 - Remote Node ATM Layer Options VPI/VCI (LLC-Multiplexing or PPPoA-Encapsulation) VPI #= 0 VCI #= 35 ATM QoS Type= UBR Peak Cell Rate (PCR)= 5400 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 . Only one set of VPI and VCI numbers needs to be specified. ENTER here to CONFIRM or ESC to CANCEL: Figure 5-2 Menu 11.6 for LLC-based Multiplexing or PPPoA Encapsulation In this case, only one set of VPI and VCI numbers need be specified for all protocols. The valid range for the VPI is 0 to 255 and for the VCI is 32 to 65535 (1 to 31 is reserved for local management of ATM traffic). The following figure uses sample IP addresses to help you understand the field of My Wan Addr in menu 11.3. Refer to the previous figure LAN and WAN IPs for a brief review of what a WAN IP is. My WAN Addr indicates the local Prestige WAN IP while Rem IP Addr indicates the peer WAN IP. 5-2 Remote Node TCP/IP Configuration Prestige 650 ADSL Router Figure 5-3 Sample IP Addresses for a TCP/IP LAN-to-LAN Connection To configure the TCP/IP parameters of a remote node, first configure fields in Menu 11.1 – Remote Node Profile, as shown in the following table. For more details on the IP Option fields, refer to Internet Access. Table 5-1 TCP/IP-Related Fields in Menu 11.1 — Remote Node Profile FIELD DESCRIPTION EXAMPLE Route Make sure IP is among the protocols in the Route field in Menu 11.1 – Remote Node Profile. IP Edit IP/Bridge Press [SPACE BAR] to select Yes and press [ENTER] to display menu. Yes Remote Node TCP/IP Configuration 5-3 Prestige 650 ADSL Router Menu 11.3 - Remote Node Network Layer Options IP Options: IP Address Assignment= Static Rem IP Addr: 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= 0.0.0.0 NAT= Full Feature Address Mapping Set=2 Metric= 2 Private= No RIP Direction= Both Version= RIP-2B Multicast= IGMP-v2 IP Policies= Bridge Options: Ethernet Addr Timeout (min)= 0 Press ENTER to Confirm or ESC to Cancel: Figure 5-4 Remote Node Network Layer Options The following table shows the fields in Menu 11.3 — Remote Node Network Layer Options. Table 5-2 TCP/IP Remote Node Configuration FIELD DESCRIPTION EXAMPLE IP Address Assignment Press [SPACE BAR] and then [ENTER] to select Dynamic if the remote node is using a dynamically assigned IP address or Static if it is using a static (fixed) IP address. You will only be able to configure this in the ISP node (the first node); all other nodes are set to Static. Static Rem IP Addr This is the IP address of the remote gateway. Type the remote Prestige’s WAN IP address here (172.16.02 in the example Figure 5-3 shown previously). If the remote Prestige’s WAN IP address is 0.0.0.0, then type 192.168.1.1 (its LAN IP address) here. 0.0.0.0 (default) Rem Subnet Mask Type the subnet mask assigned to the remote node. 0.0.0.0 (default) My WAN Addr Some implementations, especially UNIX derivatives, require separate IP network numbers for the WAN and LAN links and each end to have a unique address within the WAN network number. In that case, type the IP address assigned to the WAN port of your Prestige. NOTE: Refers to local Prestige address, not the remote router address. NAT 5-4 Press [SPACE BAR] and then [ENTER] to select Full Feature if you have multiple public WAN IP addresses for your Prestige. Full Feature Remote Node TCP/IP Configuration Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE Select SUA Only if you have just one public WAN IP address for your Prestige. The SMT uses Address Mapping Set 255 (menu 15.1 - see section 7.3.1). Select None to disable NAT. Address Mapping Set When Full Feature is selected in the NAT field, configure address mapping sets in menu 15.1. Select one of the NAT server sets (2-10) in menu 15.2 (see the NAT chapter for details) and type that number here. 2 When SUA Only is selected in the NAT field, the SMT uses NAT server set 1 in menu 15.2 (see the NAT chapter for details). Metric The metric represents the “cost” of transmission for routing purposes. IP routing uses hop count as the cost measurement, with a minimum of 1 for directly connected networks. Type a number that approximates the cost for this link. The number need not be precise, but it must be between 1 and 15. In practice, 2 or 3 is usually a good number. 2 Private This determines if the Prestige will include the route to this remote node in its RIP broadcasts. If set to Yes, this route is kept private and not included in RIP broadcast. If No, the route to this remote node will be propagated to other hosts through RIP broadcasts. Yes RIP Direction Press [SPACE BAR] and then [ENTER] to select the RIP Direction. Options are Both, In Only, Out Only or None. Both Version Press [SPACE BAR] and then [ENTER] to select the RIP version. Options are RIP-1, RIP-2B or RIP-2M. RIP-2B Multicast IGMP-v1 sets IGMP to version 1, IGMP-v2 sets IGMP to version 2 and None disables IGMP. IGMP-v2 IP Policies You can apply up to four IP Policy sets (from 12) by typing in their numbers separated by commas. 3, 4, 5, 6 When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. 5.1.2 IP Static Route Setup Static routes tell the Prestige routing information that it cannot learn automatically through other means. This can arise in cases where RIP is disabled on the LAN or a remote network is beyond the one that is directly connected to a remote node. Remote Node TCP/IP Configuration 5-5 Prestige 650 ADSL Router Each remote node specifies only the network to which the gateway is directly connected and the Prestige has no knowledge of the networks beyond. For instance, the Prestige knows about network N2 in the following figure through remote node Router 1. However, the Prestige is unable to route a packet to network N3 because it does not know that there is a route through remote node Router 1 (via Router 2). The static routes allow you to tell the Prestige about the networks beyond the remote nodes. Figure 5-5 Sample Static Routing Topology Configuration Step 1. To configure an IP static route, use Menu 12 – Static Route Setup (shown next). Menu 12 - Static Route Setup 1. IP Static Route 3. Bridge Static Route Please enter selection: Figure 5-6 Menu 12 — Static Route Setup 5-6 Remote Node TCP/IP Configuration Prestige 650 ADSL Router Step 2. From menu 12, enter 1 to open Menu 12.1 — IP Static Route Setup (shown next). Menu 12.1 - IP Static Route Setup 1. 2. 3. 4. 5. 6. 7. 8. ________ ________ ________ ________ ________ ________ ________ ________ Enter selection number: Figure 5-7 Menu 12.1 — IP Static Route Setup Step 3. Type the route number of a static route you want to configure and then press [ENTER]. Menu 12.1.1 - Edit IP Static Route Route #: 1 Route Name= ? Active= No Destination IP Address= ? IP Subnet Mask= ? Gateway IP Address= ? Metric= 2 Private= No Press ENTER to Confirm or ESC to Cancel: Figure 5-8 Edit IP Static Route The following table describes the fields for Menu 12.1.1 – Edit IP Static Route Setup. Table 5-3 Edit IP Static Route Menu Fields FIELD DESCRIPTION Route # This is the index number of the static route that you chose in menu 12.1. Route Name Type a descriptive name for this route. This is for identification purpose only. Active This field allows you to activate/deactivate this static route. Destination IP Address This parameter specifies the IP network address of the final destination. Routing is always based on network number. If you need to specify a route to a single host, use a subnet mask of 255.255.255.255 in the subnet mask field to force the network number to be identical to the host ID. Remote Node TCP/IP Configuration 5-7 Prestige 650 ADSL Router FIELD DESCRIPTION IP Subnet Mask Type the subnet mask for this destination. Follow the discussion on IP Subnet Mask in this manual. Gateway IP Address Type the IP address of the gateway. The gateway is an immediate neighbor of your Prestige that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Prestige; over WAN, the gateway must be the IP address of one of the remote nodes. Metric Metric represents the “cost” of transmission for routing purposes. IP routing uses hop count as the measurement of cost, with a minimum of 1 for directly connected networks. Type a number that approximates the cost for this link. The number need not be precise, but it must be between 1 and 15. In practice, 2 or 3 is usually a good number. Private This parameter determines if the Prestige will include the route to this remote node in its RIP broadcasts. If set to Yes, this route is kept private and is not included in RIP broadcasts. If No, the route to this remote node will be propagated to other hosts through RIP broadcasts. When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. 5-8 Remote Node TCP/IP Configuration Prestige 650 ADSL Router Chapter 6 Bridging Setup This chapter shows you how to configure the bridging parameters of your Prestige. 6.1 Bridging in General Bridging bases the forwarding decision on the MAC (Media Access Control), or hardware address, while routing does it on the network layer (IP) address. Bridging allows the Prestige to transport packets of network layer protocols that it does not route, for example, SNA, from one network to another. The caveat is that, compared to routing, bridging generates more traffic for the same network layer protocol, and it also demands more CPU cycles and memory. For efficiency reasons, do not turn on bridging unless you need to support protocols other than IP on your network. For IP, enable the routing if you need it; do not bridge what the Prestige can route. 6.2 Bridge Ethernet Setup Basically, all non-local packets are bridged to the WAN. Your Prestige does not support IPX. 6.2.1 Remote Node Bridging Setup Follow the procedure in another section to configure the protocol-independent parameters in Menu 11.1 – Remote Node Profile. For bridging-related parameters, you need to configure Menu 11.3 – Remote Node Network Layer Options. To setup Menu 11.3 – Remote Node Network Layer Options shown in the next figure, follow these steps: Step 1. In menu 11.1, make sure the Bridge field is set to Yes. Step 2. Move the cursor to the Edit IP/Bridge field, then press [SPACE BAR] to set the value to Yes and press [ENTER] to edit Menu 11.3 – Remote Node Network Layer Options. Bridging Setup 6-1 Prestige 650 ADSL Router Menu 11.3 - Remote Node Network Layer Options IP Options: IP Address Assignment= Static Rem IP Addr: 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= 0.0.0.0 NAT= Full Feature Address Mapping Set=2 Metric= 2 Private= No RIP Direction= Both Version= RIP-2B Multicast= IGMP-v2 IP Policies= Bridge Options: Ethernet Addr Timeout (min)= 0 Press ENTER to Confirm or ESC to Cancel: Figure 6-1 Menu 11.3 — Remote Node Bridging Options Table 6-1 Remote Node Bridge Options FIELD DESCRIPTION Bridge (menu 11.1) Make sure this field is set to Yes. Edit IP/Bridge (menu 11.1) Press [SPACE BAR] to select Yes and press [ENTER] to display menu 11.3. Ethernet Addr Timeout (min.) (menu 11.3) Type the time (in minutes) for the Prestige to retain the Ethernet Address information in its internal tables while the line is down. If this information is retained, your Prestige will not have to recompile the tables when the line comes back up. When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. 6.2.2 Bridge Static Route Setup Similar to network layer static routes, a bridging static route tells the Prestige the route to a node before a connection is established. You configure bridge static routes in menu 12.3.1 (go to menu 12, choose option 3, then choose a static route to edit) as shown next. 6-2 Bridging Setup Prestige 650 ADSL Router Menu 12.3.1 - Edit Bridge Static Route Route #: 1 Route Name= Active= No Ether Address= ? IP Address= Gateway Node= 1 Press ENTER to Confirm or ESC to Cancel: Figure 6-2 Menu 12.3.1 — Edit Bridge Static Route The following table describes the Edit Bridge Static Route menu. Table 6-2 Edit Bridge Static Route Menu Fields FIELD DESCRIPTION Route # This is the route index number you typed in Menu 12.3 – Bridge Static Route Setup. Route Name Type a name for the bridge static route for identification purposes. Active Indicates whether the static route is active (Yes) or not (No). Ether Address Type the MAC address of the destination computer that you want to bridge the packets to. IP Address If available, type the IP address of the destination computer that you want to bridge the packets to. Gateway Node Press [SPACE BAR] and then [ENTER] to select the number of the remote node (one to eight) that is the gateway of this static route. When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. Bridging Setup 6-3 Prestige 650 ADSL Router Chapter 7 Network Address Translation (NAT) This chapter discusses how to configure NAT on the Prestige. 7.1 Introduction NAT (Network Address Translation - NAT, RFC 1631) is the translation of the IP address of a host in a packet, for example, the source address of an outgoing packet, used within one network to a different IP address known within another network. 7.1.1 NAT Definitions Inside/outside denotes where a host is located relative to the Prestige, for example, the computers of your subscribers are the inside hosts, while the web servers on the Internet are the outside hosts. Global/local denotes the IP address of a host in a packet as the packet traverses a router, for example, the local address refers to the IP address of a host when the packet is in the local network, while the global address refers to the IP address of the host when the same packet is traveling in the WAN side. Note that inside/outside refers to the location of a host, while global/local refers to the IP address of a host used in a packet. Thus, an inside local address (ILA) is the IP address of an inside host in a packet when the packet is still in the local network, while an inside global address (IGA) is the IP address of the same inside host when the packet is on the WAN side. The following table summarizes this information. Table 7-1 NAT Definitions TERM DESCRIPTION Inside This refers to the host on the LAN. Outside This refers to the host on the WAN. Local This refers to the packet address (source or destination) as the packet travels on the LAN. Global This refers to the packet address (source or destination) as the packet travels on the WAN. NAT 7-1 Prestige 650 ADSL Router NAT never changes the IP address (either local or global) of an outside host. 7.1.2 What NAT Does In the simplest form, NAT changes the source IP address in a packet received from a subscriber (the inside local address) to another (the inside global address) before forwarding the packet to the WAN side. When the response comes back, NAT translates the destination address (the inside global address) back to the inside local address before forwarding it to the original inside host. Note that the IP address (either local or global) of an outside host is never changed. The global IP addresses for the inside hosts can be either static or dynamically assigned by the ISP. In addition, you can designate servers, for example, a web server and a telnet server, on your local network and make them accessible to the outside world. Although you can make designated servers on the LAN accessible to the outside world, it is strongly recommended that you attach those servers to the DMZ port instead. If you do not define any servers (for Many-to-One and Many-to-Many Overload mapping – see Table 7-2), NAT offers the additional benefit of firewall protection. With no servers defined, your Prestige filters out all incoming inquiries, thus preventing intruders from probing your network. For more information on IP address translation, refer to RFC 1631, The IP Network Address Translator (NAT). 7.1.3 How NAT Works Each packet has two addresses – a source address and a destination address. For outgoing packets, the ILA (Inside Local Address) is the source address on the LAN, and the IGA (Inside Global Address) is the source address on the WAN. For incoming packets, the ILA is the destination address on the LAN, and the IGA is the destination address on the WAN. NAT maps private (local) IP addresses to globally unique ones required for communication with hosts on other networks. It replaces the original IP source address (and TCP or UDP source port numbers for Many-to-One and Many-to-Many Overload NAT mapping) in each packet and then forwards it to the Internet. The Prestige keeps track of the original addresses and port numbers so incoming reply packets can have their original values restored. The following figure illustrates this. 7-2 NAT Prestige 650 ADSL Router Figure 7-1 How NAT Works 7.1.4 NAT Application The following figure illustrates a possible NAT application, where three inside LANs (logical LANs using IP Alias) behind the Prestige can communicate with three distinct WAN networks. More examples follow at the end of this chapter. NAT 7-3 Prestige 650 ADSL Router Figure 7-2 NAT Application With IP Alias 7.1.5 NAT Mapping Types NAT supports five types of IP/port mapping. They are: 1. One to One: In One-to-One mode, the Prestige maps one local IP address to one global IP address. 2. Many to One: In Many-to-One mode, the Prestige maps multiple local IP addresses to one global IP address. This is equivalent to SUA (for instance, PAT, port address translation), ZyXEL’s Single User Account feature that previous ZyXEL routers supported (the SUA Only option in today’s routers). 3. 7-4 Many to Many Overload: In Many-to-Many Overload mode, the Prestige maps the multiple local IP addresses to shared global IP addresses. NAT Prestige 650 ADSL Router 4. Many-to-Many No Overload: In Many-to-Many No Overload mode, the Prestige maps each local IP address to a unique global IP address. 5. Server: This type allows you to specify inside servers of different services behind the NAT to be accessible to the outside world although, it is highly recommended that you use the DMZ port for these servers instead. Port numbers do not change for One-to-One and Many-to-Many No Overload NAT mapping types. The following table summarizes these types. Table 7-2 NAT Mapping Types TYPE IP MAPPING SMT ABBREVIATION One-to-One ILA1ÅÆ IGA1 1:1 Many-to-One (SUA/PAT) ILA1ÅÆ IGA1 M:1 ILA2ÅÆ IGA1 … Many-to-Many Overload ILA1ÅÆ IGA1 M:M Ov ILA2ÅÆ IGA2 ILA3ÅÆ IGA1 ILA4ÅÆ IGA2 … Many-to-Many No Overload ILA1ÅÆ IGA1 M:M No OV ILA2ÅÆ IGA2 ILA3ÅÆ IGA3 … Server Server 1 IPÅÆ IGA1 Server Server 2 IPÅÆ IGA1 Server 3 IPÅÆ IGA1 NAT 7-5 Prestige 650 ADSL Router 7.2 Using NAT 7.2.1 SUA (Single User Account) Versus NAT SUA (Single User Account) is a ZyNOS implementation of a subset of NAT that supports two types of mapping, Many-to-One and Server. See section 7.3.1 for a detailed description of the NAT set for SUA. The Prestige also supports Full Feature NAT to map multiple global IP addresses to multiple private LAN IP addresses of clients or servers using mapping types as outlined in Table 7-2. 1. Choose SUA Only if you have just one public WAN IP address for your Prestige. 2. Choose Full Feature if you have multiple public WAN IP addresses for your Prestige. 7.2.2 Applying NAT You apply NAT via menus 4 or 11.3 as displayed next. The next figure shows you how to apply NAT for Internet access in menu 4. Enter 4 from the main menu to go to Menu 4 - Internet Access Setup. Menu 4 - Internet Access Setup ISP's Name= ChangeMe Encapsulation= RFC-1483 Multiplexing= LLC-based VPI #= 0 VCI #= 35 ATM QoS Type= CBR Peak Cell Rate (PCR)= 0 Sustain Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static IP Address= 0.0.0.0 Network Address Translation= SUA Only Address Mapping Set= N/A Figure 7-3 Menu 4 — Applying NAT for Internet Access The following figure shows how you apply NAT to the remote node in menu 11.1. 7-6 NAT Prestige 650 ADSL Router Step 1. Enter 11 from the main menu. Step 2. Move the cursor to the Edit IP field, press [SPACE BAR] to select Yes and then press [ENTER] to bring up Menu 11.3 - Remote Node Network Layer Options. NAT 7-7 Prestige 650 ADSL Router Menu 11.3 - Remote Node Network Layer Options IP Options: IP Address Assignment= Static Rem IP Addr: 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= 0.0.0.0 NAT= Full Feature Address Mapping Set= 2 Metric= 2 Private= No RIP Direction= Both Version= RIP-2B Multicast= IGMP-v2 IP Policies= Bridge Options: Ethernet Addr Timeout (min)= 0 Press ENTER to Confirm or ESC to Cancel: Figure 7-4 Menu 11.3 — Applying NAT to the Remote Node The following table describes the options for Network Address Translation. Table 7-3 Applying NAT in Menus 4 & 11.3 FIELD NAT DESCRIPTION Press [SPACE BAR] and then [ENTER] to select Full Feature if you have multiple public WAN IP addresses for your Prestige. The SMT uses the address mapping set that you configure and enter in the Address Mapping Set field (menu 15.1 - see section 7.3.1). Select None to disable NAT. When you select SUA Only, the SMT uses Address Mapping Set 255 (menu 15.1 - see section 7.3.1). Choose SUA Only if you have just one public WAN IP address for your Prestige. 7.3 EXAMPLE Full Feature None SUA Only NAT Setup Use the Address Mapping Sets menus and submenus to create the mapping table used to assign global addresses to computers on the LAN. You can see two NAT Address Mapping sets in menu 15.1. You can only configure Set 1. Set 255 is used for SUA. When you select Full Feature in menu 4 or 11.3, the SMT will use Set 1, which supports all mapping types as outlined in Table 7-2. When you select SUA Only, the SMT will use the pre-configured Set 255 (read only). 7-8 NAT Prestige 650 ADSL Router The Server Set is a list of LAN side servers mapped to external ports. To use this set (one set for the Prestige 10), a server rule must be set up inside the NAT Address Mapping set. Please see section 7.4 for further information on these menus. To configure NAT, enter 15 from the main menu to bring up the following screen. Menu 15 — NAT Setup 1. 2. Address Mapping Sets NAT Server Sets Enter Menu Selection Number: Figure 7-5 Menu 15 — NAT Setup 7.3.1 Address Mapping Sets Enter 1 to bring up Menu 15.1 — Address Mapping Sets. Menu 15.1 - Address Mapping Sets 1. 2. 3. 4. 5. 6. 7. 8. 255. (read only) Enter Menu Selection Number: Enter Menu Selection Number: Figure 7-6 Menu 15.1 — Address Mapping Sets SUA Address Mapping Set Enter 255 to display the next screen (see also section 7.2.1). The fields in this menu cannot be changed. NAT 7-9 Prestige 650 ADSL Router Menu 15.1.255 - Address Mapping Rules Set Name= Idx --1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Local Start IP --------------0.0.0.0 Local End IP --------------255.255.255.255 Global Start IP --------------0.0.0.0 0.0.0.0 Global End IP --------------- Type -----M-1 Server Press ENTER to Confirm or ESC to Cancel: Figure 7-7 Menu 15.1.255 — SUA Address Mapping Rules The following table explains the fields in this screen. Menu 15.1.255 is read-only. Table 7-4 SUA Address Mapping Rules FIELD Set Name This is the name of the set you selected in menu 15.1. Enter the name of a new set you want to create. Idx This is the index or rule number. Local Start IP Local Start IP is the starting local IP address (ILA) (see Figure 7-1). Local End IP is the ending local IP address (ILA). If the rule is for all local IPs, then the Start IP is 0.0.0.0 and the End IP is 255.255.255.255. Local End IP 7-10 DESCRIPTION Global Start IP This is the starting global IP address (IGA). If you have a dynamic IP, enter 0.0.0.0 as the Global Start IP. Global End IP This is the ending global IP address (IGA). Type These are the mapping types discussed above (see Table 7-2). Server allows us to specify multiple servers of different types behind NAT to this machine. See later for some examples. EXAMPLE SUA 1 0.0.0.0 255.255.255.255 0.0.0.0 Server NAT Prestige 650 ADSL Router Once you have finished configuring a rule in this menu, press [ENTER] at the message “Press ENTER to Confirm…” to save your configuration, or press [ESC] to cancel. User-Defined Address Mapping Sets Now let’s look at option 1 in menu 15.1. Enter 1 to bring up this menu. We’ll just look at the differences from the previous menu. Note the extra Action and Select Rule fields mean you can configure rules in this screen. Note also that the [?] in the Set Name field means that this is a required field and you must enter a name for the set. Menu 15.1.1 - Address Mapping Rules Set Name= NAT_SET Idx --1. 2 3. 4. 5. 6. 7. 8. 9. 10. Local Start IP --------------- Local End IP --------------- Action= Edit Global Start IP --------------- Global End IP --------------- Type ------ Select Rule= Press ENTER to Confirm or ESC to Cancel: Figure 7-8 Menu 15.1.1 — First Set If the Set Name field is left blank, the entire set will be deleted. The Type, Local and Global Start/End IPs are configured in menu 15.1.1.1 (described later) and the values are displayed here. Ordering Your Rules Ordering your rules is important because the Prestige applies the rules in the order that you specify. When a rule matches the current packet, the Prestige takes the corresponding action and the remaining rules are ignored. If there are any empty rules before your new configured rule, your configured rule will be pushed NAT 7-11 Prestige 650 ADSL Router up by that number of empty rules. For example, if you have already configured rules 1 to 6 in your current set and now you configure rule number 9. In the set summary screen, the new rule will be rule 7, not 9. Now if you delete rule 4, rules 5 to 7 will be pushed up by 1 rule, so as old rule 5 becomes rule 4, old rule 6 becomes rule 5 and old rule 7 becomes rule 6. Table 7-5 Fields in Menu 15.1.1 FIELD DESCRIPTION EXAMPLE Set Name Enter a name for this set of rules. This is a required field. If this field is left blank, the entire set will be deleted. NAT_SET Action The default is Edit. Edit means you want to edit a selected rule (see following field). Insert Before means to insert a rule before the rule selected. The rules after the selected rule will then be moved down by one rule. Delete means to delete the selected rule and then all the rules after the selected one will be advanced one rule. None disables the Select Rule item. Edit Select Rule When you choose Edit, Insert Before or Delete in the previous field the cursor jumps to this field to allow you to select the rule to apply the action in question. 1 You must press [ENTER] at the bottom of the screen to save the whole set. You must do this again if you make any changes to the set – including deleting a rule. No changes to the set take place until this action is taken. Selecting Edit in the Action field and then selecting a rule brings up the following menu, Menu 15.1.1.1 Address Mapping Rule in which you can edit an individual rule and configure the Type, Local and Global Start/End IPs. An End IP address must be numerically greater than its corresponding IP Start address. 7-12 NAT Prestige 650 ADSL Router Menu 15.1.1.1 Address Mapping Rule Type= One-to-One Local IP: Start= End = N/A Global IP: Start= End = N/A Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 7-9 Menu 15.1.1.1 — Editing/Configuring an Individual Rule in a Set Table 7-6 Menu 15.1.1.1 — Editing/Configuring an Individual Rule in a Set FIELD DESCRIPTION EXAMPLE Type Press [SPACE BAR] and then [ENTER] to select from a total of five types. These are the mapping types discussed in Table 7-2. Server allows you to specify multiple servers of different types behind NAT to this computer. See section 7.5.3 for an example. One-to-One Local IP Only local IP fields are N/A for server; Global IP fields MUST be set for Server. Start This is the starting local IP address (ILA). 0.0.0.0 End This is the ending local IP address (ILA). If the rule is for all local IPs, then put the Start IP as 0.0.0.0 and the End IP as 255.255.255.255. This field is N/A for One-to-One and Server types. N/A Start This is the starting global IP address (IGA). If you have a dynamic IP, enter 0.0.0.0 as the Global IP Start. Note that Global IP Start can be set to 0.0.0.0 only if the types are Many-to-One or Server. 0.0.0.0 End This is the ending global IP address (IGA). This field is N/A for One-to-One, Many-to-One and Server types. N/A Server Mapping Set Only available when Type is set to Server. Type a number from 1 to 10 to choose a server set from menu 15.2. Global IP NAT 7-13 Prestige 650 ADSL Router Once you have finished configuring a rule in this menu, press [ENTER] at the message “Press ENTER to Confirm…” to save your configuration, or press [ESC] to cancel. 7.4 NAT Server Sets — Port Forwarding A NAT server set is a list of inside (behind NAT on the LAN) servers, for example, web or FTP, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. Use Menu 15 — NAT Setup to forward incoming service requests to the server(s) on your local network. You may enter a single port number or a range of port numbers to be forwarded, and the local IP address of the desired server. The port number identifies a service; for example, web service is on port 80 and FTP on port 21. In some cases, such as for unknown services or where one server can support more than one service (for example both FTP and web service), it might be better to specify a range of port numbers. In addition to the servers for specified services, NAT supports a default server. A service request that does not have a server explicitly designated for it is forwarded to the default server. If the default is not defined, the service request is simply discarded. Many residential broadband ISP accounts do not allow you to run any server processes (such as a Web or FTP server) from your location. Your ISP may periodically check for servers and may suspend your account if it discovers any active services at your location. If you are unsure, refer to your ISP. The most often used port numbers are shown in the following table. Please refer to RFC 1700 for further information about port numbers. Please also refer to the included disk for more examples and details on NAT. Table 7-7 Services and Port Numbers SERVICES 7-14 PORT NUMBER ECHO 7 FTP (File Transfer Protocol) 21 Telnet 23 NAT Prestige 650 ADSL Router SERVICES PORT NUMBER SMTP (Simple Mail Transfer Protocol) 25 DNS (Domain Name System) 53 Finger 79 HTTP (Hyper Text Transfer protocol or WWW, Web) 80 POP3 (Post Office Protocol) 110 NNTP (Network News Transport Protocol) 119 SNMP (Simple Network Management Protocol) 161 SNMP trap 162 PPTP (Point-to-Point Tunneling Protocol) 1723 7.4.1 Configuring a Server behind NAT Follow these steps to configure a server behind NAT: Step 1. Enter 15 in the main menu to go to Menu 15 — NAT Setup. Step 2. Enter 2 to display Menu 15.2 — NAT Server Sets as shown next. NAT 7-15 Prestige 650 ADSL Router Menu 15.2 - NAT Server Sets 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Server Server Server Server Server Server Server Server Server Server Set Set Set Set Set Set Set Set Set Set 1 (Used for SUA Only) 2 3 4 5 6 7 8 9 10 Enter Set Number to Edit: Figure 7-10 Menu 15.2 — NAT Server Setup Step 3. Enter 1 to go to Menu 15.2.1 NAT Server Setup as follows. Menu 15.2.1 - NAT Server Setup Rule Start Port No. End Port No. IP Address --------------------------------------------------1. Default Default 0.0.0.0 2. 21 25 192.168.1.33 3. 0 0 0.0.0.0 4. 0 0 0.0.0.0 5. 0 0 0.0.0.0 6. 0 0 0.0.0.0 7. 0 0 0.0.0.0 8. 0 0 0.0.0.0 9. 0 0 0.0.0.0 10. 0 0 0.0.0.0 11. 0 0 0.0.0.0 12. 0 0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Figure 7-11 Menu 15.2.1 — NAT Server Setup Step 4. 7-16 Enter a port number in an unused Start Port No field. To forward only one port, enter it again in the End Port No field. To specify a range of ports, enter the last port to be forwarded in the End Port No field. NAT Prestige 650 ADSL Router Step 5. Enter the inside IP address of the server in the IP Address field. In the following figure, you have a computer acting as an FTP, Telnet and SMTP server (ports 21, 23 and 25) at 192.168.1.33. Step 6. Press [ENTER] at the “Press ENTER to confirm …” prompt to save your configuration after you define all the servers or press [ESC] at any time to cancel. Figure 7-12 Multiple Servers Behind NAT Example NAT 7-17 Prestige 650 ADSL Router 7.5 General NAT Examples 7.5.1 Example 1: Internet Access Only In the following Internet access example, you only need one rule where your ILAs (Inside Local addresses) all map to one dynamic IGA (Inside Global Address) assigned by your ISP. Figure 7-13 NAT Example 1 Menu 4 - Internet Access Setup ISP's Name= ChangeMe Encapsulation= RFC-1483 Multiplexing= LLC-based VPI #= 1 VCI #= 1 ATM QoS Type= UBR Peak Cell Rate (PCR)= 5500 Sustained Cell Rate (SCR)= 0 Maximum Burst Size (MBS)= 0 My Login= N/A My Password= N/A ENET ENCAP Gateway= N/A IP Address Assignment= Static IP Address= 0.0.0.0 Network Address Translation= SUA Only Address Mapping Set= Figure 7-14 Menu 4 — Internet Access & NAT Example 7-18 NAT Prestige 650 ADSL Router From menu 4, choose the SUA Only option from the Network Address Translation field. This is the Many-to-One mapping discussed in section 7.5. The SUA Only read-only option from the Network Address Translation field in menus 4 and 11.3 is specifically pre-configured to handle this case. 7.5.2 Example 2: Internet Access with an Inside Server Figure 7-15 NAT Example 2 In this case, you do exactly as above (use the convenient pre-configured SUA Only set) and also go to menu 15.2 to specify the Inside Server behind the NAT as shown in the next figure. NAT 7-19 Prestige 650 ADSL Router Menu 15.2.1 - NAT Server Setup (Used for SUA Only) Rule Start Port No. End Port No. IP Address --------------------------------------------------1. Default Default 192.168.1.10 2. 0 0 0.0.0.0 3. 0 0 0.0.0.0 4. 0 0 0.0.0.0 5. 0 0 0.0.0.0 6. 0 0 0.0.0.0 7. 0 0 0.0.0.0 8. 0 0 0.0.0.0 9. 0 0 0.0.0.0 10. 0 0 0.0.0.0 11. 0 0 0.0.0.0 12. 0 0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Figure 7-16 Menu 15.2.1 — Specifying an Inside Server 7.5.3 Example 3: Multiple Public IP Addresses With Inside Servers In this example, there are 3 IGAs from our ISP. There are many departments but two have their own FTP server. All departments share the same router. The example will reserve one IGA for each department with an FTP server and all departments use the other IGA. Map the FTP servers to the first two IGAs and the other LAN traffic to the remaining IGA. Map the third IGA to an inside web server and mail server. Four rules need to be configured, two bi-directional and two uni-directional as follows. Rule 1. Map the first IGA to the first inside FTP server for FTP traffic in both directions (1 : 1 mapping, giving both local and global IP addresses). Rule 2. Map the second IGA to our second inside FTP server for FTP traffic in both directions (1 : 1 mapping, giving both local and global IP addresses). Rule 3. Map the other outgoing LAN traffic to IGA3 (Many : 1 mapping). Rule 4. You also map your third IGA to the web server and mail server on the LAN. Type Server allows you to specify multiple servers, of different types, to other computers behind NAT on the LAN. The example situation looks somewhat like this: 7-20 NAT Prestige 650 ADSL Router Figure 7-17 NAT Example 3 Step 1. In this case you need to configure Address Mapping Set 1 from Menu 15.1 - Address Mapping Sets. Therefore you must choose the Full Feature option from the Network Address Translation field (in menu 4 or menu 11.3) in The following figure shows how to configure the first rule . Step 2. Then enter 15 from the main menu. Step 3. Enter 1 to configure the Address Mapping Sets. Step 4. Enter 1 to begin configuring this new set. Enter a Set Name, choose the Edit Action and then enter 1 for the Select Rule field. Press [ENTER] to confirm. Step 5. Select Type as One-to-One (direct mapping for packets going both ways), and enter the local Start IP as 192.168.1.10 (the IP address of FTP Server 1), the global Start IP as 10.132.50.1 (our first IGA). (See Figure 7-19). Step 6. Repeat the previous step for rules 2 to 4 as outlined above. Step 7. When finished, menu 15.1.1 should look like as shown in . NAT 7-21 Prestige 650 ADSL Router Menu 11.3 - Remote Node Network Layer Options IP Options: IP Address Assignment= Static Rem IP Addr: 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= 0.0.0.0 NAT= Full Feature Address Mapping Set= 2 Metric= 2 Private= No RIP Direction= Both Version= RIP-2B Multicast= IGMP-v2 IP Policies= Bridge Options: Ethernet Addr Timeout (min)= 0 Press ENTER to Confirm or ESC to Cancel: Figure 7-18 Example 3: Menu 11.3 The following figure shows how to configure the first rule Menu 15.1.1.1 Address Mapping Rule Type= One-to-One Local IP: Start= 192.168.1.10 End = N/A Global IP: Start= 10.132.50.1 End = N/A Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 7-19 Example 3: Menu 15.1.1.1 7-22 NAT Prestige 650 ADSL Router Menu 15.1.1 - Address Mapping Rules Set Name= Example3 Idx Local Start IP --- --------------1. 192.168.1.10 2 192.168.1.11 3. 0.0.0.0 4. 5. 6. 7. 8. 9. 10. Local End IP --------------255.255.255.255 Action= Edit Global Start IP --------------10.132.50.1 10.132.50.2 10.132.50.3 10.132.50.3 Global End IP --------------- Type -----1-1 1-1 M-1 Server Select Rule= Press ENTER to Confirm or ESC to Cancel: Figure 7-20 Example 3: Final Menu 15.1.1 Now configure the IGA3 to map to our web server and mail server on the LAN. Step 8. Enter 15 from the main menu. Step 9. Enter 2 in Menu 15 - NAT Setup. Step 10. Enter 1 in Menu 15.2 - NAT Server Sets to see the following menu. Configure it as shown. NAT 7-23 Prestige 650 ADSL Router Menu 15.2.1 - NAT Server Setup Rule Start Port No. End Port No. IP Address --------------------------------------------------1. Default Default 0.0.0.0 2. 80 80 192.168.1.21 3. 25 25 192.168.1.20 4. 0 0 0.0.0.0 5. 0 0 0.0.0.0 6. 0 0 0.0.0.0 7. 0 0 0.0.0.0 8. 0 0 0.0.0.0 9. 0 0 0.0.0.0 10. 0 0 0.0.0.0 11. 0 0 0.0.0.0 12. 0 0 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Example 3: Menu 15.2.1 7.5.4 Example 4: NAT Unfriendly Application Programs Some applications do not support NAT Mapping using TCP or UDP port address translation. In this case it is better to use Many-to-Many No Overload mapping as port numbers do not change for Many-toMany No Overload (and One-to-One) NAT mapping types. The following figure illustrates this. Figure 7-21 NAT Example 4 7-24 NAT Prestige 650 ADSL Router Other applications such as some gaming programs are NAT unfriendly because they embed addressing information in the data stream. These applications won’t work through NAT even when using One-to-One and Many-to-Many No Overload mapping types. Follow the steps outlined in example 3 to configure these two menus as follows. Menu 15.1.1.1 Address Mapping Rule Type= Many-to-Many No Overload Local IP: Start= 192.168.1.10 End = 192.168.1.12 Global IP: Start= 10.132.50.1 End = 10.132.50.3 Server Mapping Set= N/A Press ENTER to Confirm or ESC to Cancel: Figure 7-22 Example 4: Menu 15.1.1.1 — Address Mapping Rule After you’ve configured your rule, you should be able to check the settings in menu 15.1.1 as shown next. NAT 7-25 Prestige 650 ADSL Router Menu 15.1.1 - Address Mapping Rules Set Name= Example4 Idx --1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Local Start IP --------------192.168.1.10 Local End IP --------------192.168.1.12 Action= Edit Global Start IP --------------10.132.50.1 Global End IP --------------10.132.50.3 Type -----M:M NO OV Select Rule= Press ENTER to Confirm or ESC to Cancel: Figure 7-23 Example 4: Menu 15.1.1 — Address Mapping Rules 7-26 NAT Advanced Management Part III: ADVANCED MANAGEMENT This part discusses Filtering, SNMP, System Information and Diagnosis, Firmware and Configuration File Maintenance, System Maintenance and Information, IP Policy Routing, Call Scheduling and Remote Management. III Prestige 650 ADSL Router Chapter 8 Filter Configuration This chapter shows you how to create and apply filters. 8.1 About Filtering Your Prestige uses filters to decide whether or not to allow passage of a data packet and/or to make a call. There are two types of filter applications: data filtering and call filtering. Filters are subdivided into device and protocol filters, which are discussed later. Data filtering screens data to determine if the packet should be allowed to pass. Data filters are divided into incoming and outgoing filters, depending on the direction of the packet relative to a port. Data filtering can be applied on either the WAN side or the Ethernet side. Call filtering is used to determine if a packet should be allowed to trigger a call. Outgoing packets must undergo data filtering before they encounter call filtering. Call filters are divided into two groups, the built-in call filters and user-defined call filters. Your Prestige has built-in call filters that prevent administrative, for example, RIP packets from triggering calls. These filters are always enabled and not accessible to you. Your Prestige applies the built-in filters first and then the user-defined call filters, if applicable, as shown next. Filter Configuration 8-1 Prestige 650 ADSL Router Call Filtering Outgoing Packet No match Data Match Drop packet No match Built-in default Call Filters Match Drop packet if line not up No match User-defined Call Filters (if applicable) Active Data Initiate call if line not up Send packet and reset Idle Timer Match Drop packet if line not up Or Or Send packet but do not reset Idle Timer Send packet but do not reset Idle Timer Figure 8-1 Outgoing Packet Filtering Process Two sets of factory filter rules have been configured in menu 21 to prevent NetBIOS traffic from triggering calls. A summary of their filter rules is shown in the figures that follow. The following figure illustrates the logic flow when executing a filter rule. 8-2 Filter Configuration Prestige 650 ADSL Router Start Packet intoFilter Fetch First Filter Set Filter Set Fetch Next Filter Set Fetch First Filter Rule Fetch Next Filter Rule Yes Yes Yes Next Filter Set Available? No Next filter Rule Available? No Active? Yes No Check Next Rule Execute Filter Rule Forward Drop Drop Packet Accept Packet Figure 8-2 Filter Rule Process You can apply up to four filter sets to a particular port to block various types of packets. Because each filter set can have up to six rules, you can have a maximum of 24 rules active for a single port. Filter Configuration 8-3 Prestige 650 ADSL Router For incoming packets, your Prestige applies data filters only. Packets are processed depending on whether a match is found. The following sections describe how to configure filter sets. The Filter Structure of the Prestige A filter set consists of one or more filter rules. Usually, you would group related rules, for example, all the rules for NetBIOS, into a single set and give it a descriptive name. You can configure up to twelve filter sets with six rules in each set, for a total of 72 filter rules in the system. 8.2 Configuring a Filter Set To configure a filter set, follow the steps shown next. Step 1. Enter 21 in the main menu to display Menu 21 – Filter Set Configuration. Menu 21 - Filter Set Configuration Filter Set # -----1 2 3 4 5 6 Comments ----------------NetBIOS_WAN NetBIOS_LAN TELNET_WAN PPPoE FTP_WAN _______________ Filter Set # -----7 8 9 10 11 12 Comments ----------------_______________ _______________ _______________ _______________ WebSet1 WebSet2 Enter Filter Set Number to Configure= 0 Edit Comments= N/A Press ENTER to Confirm or ESC to Cancel: Figure 8-3 Menu 21 — Filter Set Configuration Step 2. Type the filter set to configure (no. 1 to 12) and press [ENTER]. Filter rule set 11 and 12 are used by the Web Configurator. Your custom configuration will be replaced if you use rule 11 or 12. Step 3. 8-4 Type a descriptive name or comment in the Edit Comments field and press [ENTER]. Filter Configuration Prestige 650 ADSL Router Step 4. Press [ENTER] at the message “Press [ENTER] to confirm…” to display Menu 21.1 – Filter Rules Summary (that is, if you selected filter set 1 in menu 21). Menu 21.1 - Filter Rules Summary # A Type Filter Rules M m n - - ---- -------------------------------------------- --------- - - 1 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=137 N D N 2 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=138 N D N 3 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=139 N D N 4 Y IP Pr=17, SA=0.0.0.0, DA=0.0.0.0, DP=137 N D N 5 Y IP Pr=17, SA=0.0.0.0, DA=0.0.0.0, DP=138 N D N 6 Y IP Pr=17, SA=0.0.0.0, DA=0.0.0.0, DP=139 N D F Enter Filter Rule Number (1-6) to Configure: 1 Figure 8-4 NetBIOS_WAN Filter Rules Summary Menu 21.2 - Filter Rules Summary # A Type Filter Rules M m n - - ---- -------------------------------------------- --------- - - 1 Y IP Pr=17, SA=0.0.0.0, SP=137, DA=0.0.0.0, DP=53 N D F 2 Y 3 Y 4 Y 5 Y 6 Y Enter Filter Rule Number (1-6) to Configure: 1 Figure 8-5 NetBIOS_LAN Filter Rules Summary Filter Configuration 8-5 Prestige 650 ADSL Router Menu 21.3 - Filter Rules Summary # 1 2 3 4 5 6 A Type Filter Rules M m n - ---- --------------------------------------------------------------- - - Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=23 N D F N N N N N Enter Filter Rule Number (1-6) to Configure: Figure 8-6 Telnet_WAN Filter Rules Summary Menu 21.4 - Filter Rules Summary # A Type Filter Rules M m n - - ---- --------------------------------------------------------------- - - 1 Y Gen Off=12, Len=2, Mask=ffff, Value=8863 N F N 2 Y Gen Off=12, Len=2, Mask=ffff, Value=8864 N F D 3 N 4 N 5 N 6 N Enter Filter Rule Number (1-6) to Configure: Figure 8-7 PPPoE Filter Rules Summary 8-6 Filter Configuration Prestige 650 ADSL Router Menu 21.5 - Filter Rules Summary # 1 2 3 4 5 6 A Type - ---Y IP N N N N N Filter Rules M m n -------------------------------------------------------------- - - PR=6, SA=0.0.0.0, DA=0.0.0.0, DP=21 N D F Enter Filter Rule Number (1-6) to Configure: Figure 8-8 FTP_WAN Filter Rules Summary In filter rule 6, FTP_TELNET_WEB, the WEB means that HTTP and TFTP traffic are blocked. Menu 21.12 - Filter Rules Summary # A Type Filter Rules M m n - - ---- --------------------------------------------------------------- - - 1 Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=21 N D N 2 N IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=23 N D N 3 N IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=80 N D N 4 N IP Pr=17, SA=0.0.0.0, DA=0.0.0.0, DP=69 N D F 5 N 6 N Figure 8-9 WebSet Filter Rules Summary 8.2.1 Filter Rules Summary Menus The following tables briefly describe the abbreviations used in menus 21.1 and 21.2. Filter Configuration 8-7 Prestige 650 ADSL Router Table 8-1 Abbreviations Used in the Filter Rules Summary Menu FIELD DESCRIPTION # The filter rule number: 1 to 6. A Active: “Y” means the rule is active. “N” means the rule is inactive. Type The type of filter rule: “GEN” for Generic, “IP” for TCP/IP. Filter Rules These parameters are displayed here. M More. “Y” means there are more rules to check which form a rule chain with the present rule. An action cannot be taken until the rule chain is complete. “N” means there are no more rules to check. You can specify an action to be taken for instance, forward the packet, drop the packet or check the next rule. For the latter, the next rule is independent of the rule just checked. m Action Matched. “F” means to forward the packet immediately and skip checking the remaining rules. “D” means to drop the packet. “N“ means to check the next rule. n Action Not Matched. “F” means to forward the packet immediately and skip checking the remaining rules. “D” means to drop the packet. “N” means to check the next rule. The protocol dependent filter rules abbreviation are listed as follows: Table 8-2 Rule Abbreviations Used FILTER TYPE DESCRIPTION IP Pr Protocol SA Source Address SP Source Port Number DA Destination Address DP Destination Port Number Off Offset Len Length GEN 8-8 Filter Configuration Prestige 650 ADSL Router 8.3 Configuring a Filter Rule To configure a filter rule, type its number in Menu 21.1 – Filter Rules Summary and press [ENTER] to open menu 21.1.1 for the rule. There are two types of filter rules: TCP/IP and Generic. Depending on the type of rule, the parameters for each type will be different. Use [SPACE BAR] to select the type of rule that you want to create in the Filter Type field and press [ENTER] to open the respective menu. To speed up filtering, all rules in a filter set must be of the same class, for instance, protocol filters or generic filters. The class of a filter set is determined by the first rule that you create. When applying the filter sets to a port, separate menu fields are provided for protocol and device filter sets. If you include a protocol filter set in a device filters field or vice versa, the Prestige will warn you and will not allow you to save. 8.3.1 TCP/IP Filter Rule This section shows you how to configure a TCP/IP filter rule. TCP/IP rules allow you to base the rule on the fields in the IP and the upper layer protocol, for example, UDP and TCP headers. To configure TCP/IP rules, select TCP/IP Filter Rule from the Filter Type field and press [ENTER] to open Menu 21.1.1 – TCP/IP Filter Rule, as shown next. Filter Configuration 8-9 Prestige 650 ADSL Router Menu 21.1.1 - TCP/IP Filter Rule Filter #: 1,1 Filter Type= TCP/IP Filter Rule Active= Yes IP Protocol= 6 IP Source Route= No Destination: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= 137 Port # Comp= Equal Source: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= 0 Port # Comp= None TCP Estab= No More= No Log= None Action Matched= Check Next Rule Action Not Matched= Check Next Rule Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 8-10 Menu 21.1.1 — TCP/IP Filter Rule The following table describes how to configure your TCP/IP filter rule. Table 8-3 TCP/IP Filter Rule Menu Fields FIELD DESCRIPTION EXAMPLE Filter # This is the filter set, filter rule coordinates, for instance, 2, 3 refers to the second filter set and the third filter rule of that set. 1,1 Filter Type Use [SPACE BAR] and then [ENTER] to choose a rule. Parameters displayed for each type will be different. Choices are TCP/IP Filter Rule or Generic Filter Rule. TCP/IP Filter Rule Active Select Yes to activate or No to deactivate the filter rule. No IP Protocol This is the upper layer protocol, for example, TCP is 6, UDP is 17 and ICMP is 1. The value must be between 0 and 255. A value of O matches ANY protocol. 0 to 255 IP Source Route IP Source Route is an optional header that dictates the route an IP packet takes from its source to its destination. If Yes, the rule applies to any packet with an IP source route. The majority of IP packets do not have source route. No (default) 8-10 Filter Configuration Prestige 650 ADSL Router FIELD Destination: IP Addr IP Mask DESCRIPTION EXAMPLE Type the destination IP address of the packet you want to filter. This field is ignored if it is 0.0.0.0. IP address Type the IP mask to apply to the Destination: IP Addr field. IP mask Port # Type the destination port of the packets you want to filter. The field range is 0 to 65535. A 0 field is ignored. 0 to 65535 Port # Comp Select the comparison to apply to the destination port in the packet against the value given in Destination: Port #. Choices are None, Less, Greater, Equal or Not Equal. None Source: IP Addr Type the source IP Address of the packet you want to filter. A 0.0.0.0 field is ignored. IP Mask Type the IP mask to apply to the Source: IP Addr field. Port # Port # Comp Type the source port of the packets you want to filter. The range of this field is 0 to 65535. A 0 field is ignored. Select the comparison to apply to the source port in the packet against the value given in Source: Port # field. Choices are None, Less, Greater, Equal or Not Equal. IP address IP mask 0 to 65535 None TCP Estab This applies only when the IP Protocol field is 6, TCP. If Yes, the rule matches packets that want to establish TCP connection(s) (SYN=1 and ACK=0); else it is ignored. No (default) More If Yes, a matching packet is passed to the next filter rule before an action is taken or else the packet is disposed of according to the action fields. No (default) If More is Yes, then Action Matched and Action Not Matched will be N/A. Log Select the logging option from the following: None – No packets will be logged. None Action Matched – Only packets that match the rule parameters will be logged. Action Not Matched – Only packets that do not match the rule parameters will be logged. Both – All packets will be logged. Filter Configuration 8-11 Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE Action Matched Select the action for a matching packet. Choices are Check Next Rule, Forward or Drop. Check Next Rule (default) Action Not Matched Select the action for a packet not matching the rule. Choices are Check Next Rule, Forward or Drop. Check Next Rule (default) When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. The following figure illustrates the logic flow of an IP filter. 8-12 Filter Configuration Prestige 650 ADSL Router Packet into IP Filter Filter Active? No Yes Apply SrcAddrMask to Src Addr Check Src IP Addr Not Matched Matched Apply DestAddrMask to Dest Addr Check Dest IP Addr Not Matched Matched Check IP Protocol Not Matched Matched Check Src & Dest Port Not Matched Matched More? Yes No Action Matched Drop Drop Packet Action Not Matched Check Next Rule Check Next Rule Drop Forward Forward Check Next Rule Accept Packet Figure 8-11 Executing an IP Filter Filter Configuration 8-13 Prestige 650 ADSL Router 8.3.2 Generic Filter Rule This section shows you how to configure a generic filter rule. The purpose of generic rules is to allow you to filter non-IP packets. For IP, it is generally easier to use the IP rules directly. For generic rules, the Prestige treats a packet as a byte stream as opposed to an IP packet. You specify the portion of the packet to check with the Offset (from 0) and the Length fields, both in bytes. The Prestige applies the Mask (bit-wise ANDing) to the data portion before comparing the result against the Value to determine a match. The Mask and Value fields are specified in hexadecimal numbers. Note that it takes two hexadecimal digits to represent a byte, so if the length is 4, the value in either field will take 8 digits, for example, FFFFFFFF. To configure a generic rule select an empty filter set in menu 21, for example 5. Select Generic Filter Rule in the Filter Type field and press [ENTER] to open Menu 21.5.1 – Generic Filter Rule, as shown in the following figure. Menu 21.5.1 - Generic Filter Rule Filter #: 5,1 Filter Type= Generic Filter Rule Active= No Offset= 0 Length= 0 Mask= N/A Value= N/A More= No Log= None Action Matched= Check Next Rule Action Not Matched= Check Next Rule Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 8-12 Menu 21.5.1 — Generic Filter Rule The next table describes the fields in the Generic Filter Rule menu. 8-14 Filter Configuration Prestige 650 ADSL Router Table 8-4 Generic Filter Rule Menu Fields FIELD DESCRIPTION EXAMPLE Filter # This is the filter set, filter rule coordinates, for instance, 2, 3 refers to the second filter set and the third rule of that set. 5,1 Filter Type Press [SPACE BAR] and then [ENTER] to select a type of rule. Parameters displayed below each type will be different. Choices are Generic Filter Rule or TCP/IP Filter Rule. Active Select Yes to turn on or No to turn off the filter rule. No (default) Offset Type the starting byte of the data portion in the packet that you want to compare. The range for this field is from 0 to 255. 0 (default) Length Type the byte count of the data portion in the packet that you want to compare. The range for this field is 0 to 8. 0 (default) Mask Type the mask (in Hexadecimal) to apply to the data portion before comparison. Value Type the value (in Hexadecimal) to compare with the data portion. More If Yes, a matching packet is passed to the next filter rule before an action is taken or else the packet is disposed of according to the action fields. Generic Filter Rule No (default) If More is Yes, then Action Matched and Action Not Matched will be N/A. Log Select the logging option from the following: None – No packets will be logged. Action Matched – Only matching packets and rules will be logged. Action Not Matched – Only packets that do not match the rule parameters will be logged. Both – All packets will be logged. None Action Matched Select the action for a matching packet. Choices are Check Next Rule, Forward or Drop. Check Next Rule (default) Action Not Matched Select the action for a packet not matching the rule. Choices are Check Next Rule, Forward or Drop. Check Next Rule (default) When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. Filter Configuration 8-15 Prestige 650 ADSL Router 8.4 Filter Types and NAT There are two classes of filter rules, Generic Filter Device rules and Protocol Filter (TCP/IP) rules. Generic Filter rules act on the raw data from/to LAN and WAN. Protocol Filter rules act on IP packets. When NAT (Network Address Translation) is enabled, the inside IP address and port number are replaced on a connection-by-connection basis, which makes it impossible to know the exact address and port on the wire. Therefore, the Prestige applies the protocol filters to the “native” IP address and port number before NAT for outgoing packets and after NAT for incoming packets. On the other hand, the generic (or device) filters are applied to the raw packets that appear on the wire. They are applied at the point where the Prestige is receiving and sending the packets; for instance, the interface. The interface can be an Ethernet, or any other hardware port. The following figure illustrates this. Figure 8-13 Protocol and Device Filter Sets 8.5 Example Filter Let’s look at an example to block outside users from telnetting into the Prestige. See the included disk for example filters. 8-16 Filter Configuration Prestige 650 ADSL Router Figure 8-14 Sample Telnet Filter Step 1. Enter 21 from the main menu to open Menu 21 — Filter Set Configuration. Step 2. Enter the index number of the filter set you want to configure (in this case 3). Step 3. Type a descriptive name or comment in the Edit Comments field (for example, TELNET_WAN) and press [ENTER]. Filter Configuration 8-17 Prestige 650 ADSL Router Step 4. Press [ENTER] at the message “Press [ENTER] to confirm or [ESC] to cancel” to open Menu 21.3.1 — TCP/IP Filter Rule. Menu 21.3.1 - TCP/IP Filter Rule Filter #: 3,1 Filter Type= TCP/IP Filter Rule Active= Yes IP Protocol= 6 IP Source Route= No Destination: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= 23 Port # Comp= Equal Source: IP Addr= 0.0.0.0 IP Mask= 0.0.0.0 Port #= Port # Comp= None TCP Estab= No More= No Log= None Action Matched= Drop Action Not Matched= Forward Press [SPACE BAR] to choose this filter rule type. The first filter rule type determines all subsequent filter types within a set. Select Yes to make the rule active. 6 is the TCP protocol. Press ENTER to Confirm or ESC to Cancel: The port number for the telnet service (TCP protocol) is 23. See There are no more rules to Select Equal here RFC-1060 for port numbers of well- check. as we are looking known services. for packets going Select Drop here so that the to port 23 only. packet will be dropped if its destination is the telnet port. Select Forward here so that the packet will be forwarded if its destination is not the telnet port and there are no more rules in this filter set to check. Select Next if there are more rules to check. Figure 8-15 Sample Filter — Menu 21.3.1 Step 5. Type 1 to configure the first filter rule. Make the entries in this menu as shown next. When you press [ENTER] to confirm, the following screen appears. Note that there is only one filter rule in this set. 8-18 Filter Configuration Prestige 650 ADSL Router Menu 21.1 - Filter Rules Summary # 1 2 3 4 5 6 A Type Filter Rules M m n - ---- --------------------------------------------------------------- - - Y IP Pr=6, SA=0.0.0.0, DA=0.0.0.0, DP=23 N D F N N N N N Enter Filter Rule Number (1-6) to Configure: 1 This shows you that you have M = N means an action can be taken immediately. configured and activated (A = Y) a The action is to drop the packet (m = D) if the TCP/IP filter rule (Type = IP, Pr = 6) action is matched and to forward the packet for destination telnet ports (DP = immediately (n = F) if the action is not matched no 23). matter whether there are more rules to be checked (there aren’t in this example). Figure 8-16 Sample Filter Rules Summary — Menu 21.1 After you have created the filter set, you must apply it. Step 1. Enter 11 in the main menu to display menu 11 and type the remote node number to edit. Step 2. Go to the Edit Filter Sets field, press [SPACE BAR] to choose Yes and press [ENTER]. Step 3. This brings you to menu 11.5. Apply the example filter set (for example, filter set 3) in this menu as shown in the next section. 8.6 Applying Filters and Factory Defaults This section shows you where to apply the filter(s) after you design it (them). Sets of factory default filter rules have been configured in menu 21 (but have not been applied) to filter traffic. Filter Configuration 8-19 Prestige 650 ADSL Router Table 8-5 Filter Sets Table FILTER SETS DESCRIPTION Input Filter Sets: Apply filters for incoming traffic. You may apply protocol or device filter rules. See earlier in this chapter for information on filters. Output Filter Sets: Apply filters for traffic leaving the Prestige. You may apply filter rules for protocol or device filters. See earlier in this section for information on types of filters. Call Filter Sets: Apply filters to decide if a packet should be allowed to trigger a call. 8.6.1 Ethernet Traffic You seldom need to filter Ethernet traffic; however, the filter sets may be useful to block certain packets, reduce traffic and prevent security breaches. Go to menu 3.1 (shown next) and type the number(s) of the filter set(s) that you want to apply as appropriate. You can choose up to four filter sets (from twelve) by typing their numbers separated by commas, for example, 3, 4, 6, 11. The factory default filter set, NetBIOS_LAN, is inserted in the protocol filters field under Input Filter Sets in menu 3.1 in order to prevent local NetBIOS messages from triggering calls to the DNS server. Menu 3.1 – LAN Port Filter Setup Input Filter Sets: protocol filters= 2 device filters= Output Filter Sets: protocol filters= device filters= Press ENTER to Confirm or ESC to Cancel: Apply filter 2 to block NETBIOS traffic from the LAN Figure 8-17 Filtering Ethernet Traffic 8.6.2 Remote Node Filters Go to menu 11.5 (shown next) and type the number(s) of the filter set(s) as appropriate. You can cascade up to four filter sets by typing their numbers separated by commas. The factory default filter set, NetBIOS_WAN, is inserted in the protocol filters field under Call Filter Sets in menu 11.5 to block local NetBIOS traffic from triggering calls to the ISP. 8-20 Filter Configuration Prestige 650 ADSL Router Apply filter 3 to Menu 11.5 - Remote Node Filter Input Filter Sets: protocol filters= 3 device filters= Output Filter Sets: protocol filters= 1 block Telnet, FTP and Web traffic from the WAN. Apply filter 1 to block NETBIOS traffic to the WAN. Figure 8-18 Filtering Remote Node Traffic Note that call filter sets are visible when you select PPPoA or PPPoE encapsulation. Filter Configuration 8-21 Prestige 650 ADSL Router Chapter 9 SNMP Configuration This chapter explains SNMP Configuration menu 22. SNMP is only available if TCP/IP is configured. 9.1 About SNMP Simple Network Management Protocol is a protocol used for exchanging management information between network devices. SNMP is a member of the TCP/IP protocol suite. Your Prestige supports SNMP agent functionality, which allows a manager station to manage and monitor the Prestige through the network. The Prestige supports SNMP version one (SNMPv1). The next figure illustrates an SNMP management operation. SNMP is only available if TCP/IP is configured. Figure 9-1 SNMP Management Model SNMP Configuration 9-1 Prestige 650 ADSL Router An SNMP managed network consists of two main components: agents and a manager. An agent is a management software module that resides in a managed device (the Prestige). An agent translates the local management information from the managed device into a form compatible with SNMP. The manager is the console through which network administrators perform network management functions. It executes applications that control and monitor managed devices. The managed devices contain object variables/managed objects that define each piece of information to be collected about a device. Examples of variables include such as number of packets received, node port status etc. A Management Information Base (MIB) is a collection of managed objects. SNMP allows a manager and agents to communicate for the purpose of accessing these objects. SNMP itself is a simple request/response protocol based on the manager/agent model. The manager issues a request and the agent returns responses using the following protocol operations: • Get - Allows the manager to retrieve an object variable from the agent. • GetNext - Allows the manager to retrieve the next object variable from a table or list within an agent. In SNMPv1, when a manager wants to retrieve all elements of a table from an agent, it initiates a Get operation, followed by a series of GetNext operations. • Set - Allows the manager to set values for object variables within an agent. • Trap - Used by the agent to inform the manager of some events. 9.2 Supported MIBs The Prestige supports RFC-1215 and MIB II as defined in RFC-1213. The focus of the MIBs is to let administrators collect statistic data and monitor status and performance. 9.3 SNMP Configuration To configure SNMP, select option 22 from the main menu to open Menu 22 — SNMP Configuration as shown next. The “community” for Get, Set and Trap fields is SNMP terminology for password. 9-2 SNMP Configuration Prestige 650 ADSL Router Menu 22 - SNMP Configuration SNMP: Get Community= public Set Community= public Trusted Host= 0.0.0.0 Trap: Community= public Destination= 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Figure 9-2 Menu 22 — SNMP Configuration The following table describes the SNMP configuration parameters. Table 9-1 SNMP Configuration Menu Fields FIELD DESCRIPTION EXAMPLE Get Community Type the Get Community, which is the password for the incoming Get- and GetNext requests from the management station. public Set Community Type the Set community, which is the password for incoming Set requests from the management station. public Trusted Host If you enter a trusted host, your Prestige will only respond to SNMP messages from this address. A blank (default) field means your Prestige will respond to all SNMP messages it receives, regardless of source. 0.0.0.0 SNMP: Trap: public Community Type the trap community, which is the password sent with each trap to the SNMP manager. Destination Type the IP address of the station to send your SNMP traps to. 0.0.0.0 When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. SNMP Configuration 9-3 Prestige 650 ADSL Router 9.4 SNMP Traps The Prestige will send traps to the SNMP manager when any one of the following events occurs: Table 9-2 SNMP Traps TRAP # TRAP NAME DESCRIPTION 1 coldStart (defined in RFC-1215) A trap is sent after booting (power on). 2 warmStart (defined in RFC-1215) A trap is sent after booting (software reboot). 3 linkUp (defined in RFC-1215) A trap is sent with the port number. 4 authenticationFailure (defined in RFC-1215) A trap is sent to the manager when receiving any SNMP get or set requirements with wrong community (password). 6 linkDown (defined in RFC-1215) A trap is sent with the port number when any of the links are down. See the following table. The port number is its interface index under the interface group. Table 9-3 Ports and Permanent Virtual Circuits 9-4 PORT PVC (PERMANENT VIRTUAL CIRCUIT) 1 Ethernet LAN 2 1 3 2 … … 13 12 14 xDSL SNMP Configuration Prestige 650 ADSL Router Chapter 10 System Information and Diagnosis This chapter covers the information and diagnostic tools in SMT menus 24.1 to 24.4. These tools include updates on system status, port status, log and trace capabilities and upgrades for the system software. This chapter describes how to use these tools in detail. Type 24 in the main menu to open Menu 24 – System Maintenance, as shown in the following figure. Menu 24 - System Maintenance 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. System Status System Information and Console Port Speed Log and Trace Diagnostic Backup Configuration Restore Configuration Upload Firmware Command Interpreter Mode Call Control Time and Date Setting Remote Management Enter Menu Selection Number: Figure 10-1 Menu 24 — System Maintenance 10.1 System Status The first selection, System Status gives you information on the status and statistics of the ports, as shown next. System Status is a tool that can be used to monitor your Prestige. Specifically, it gives you information on your ADSL telephone line status, number of packets sent and received. Enter 24 to display Menu 24 — System Maintenance. Enter 1 to display Menu 24.1 — System Maintenance — Status. Entering 1 resets the counters; [ESC] takes you back to the previous screen. The following table describes the fields present in Menu 24.1 — System Maintenance — Status which are read-only and meant for diagnostic purposes. System Information and Diagnosis 10-1 Prestige 650 ADSL Router Menu 24.1 - System Maintenance – Status hh:mm:ss Sat. Jan. 01, 2000 Node-Lnk 1-ENET 2 3 4 5 6 7 8 Status Up N/A N/A N/A N/A N/A N/A N/A TxPkts 211 0 0 0 0 0 0 0 RxPkts 0 0 0 0 0 0 0 0 Errors 0 0 0 0 0 0 0 0 Tx B/s 0 0 0 0 0 0 0 0 Rx B/s 0 0 0 0 0 0 0 0 Up Time 0:26:20 0:00:00 0:00:00 0:00:00 0:00:00 0:00:00 0:00:00 0:00:00 My WAN IP (from ISP) : Ethernet: Status: 10M/Half Duplex Collisions: 0 CPU Load= 3.8% Tx Pkts: 53 Rx Pkts: 36 Press Command: COMMANDS: 1-Reset Counters WAN: Line Status: Up Upstream Speed: Downstream Speed: ESC-Exit Figure 10-2 Menu 24.1 — System Maintenance — Status The following table describes the fields present in Menu 24.1 — System Maintenance — Status. Table 10-1 System Maintenance — Status Menu Fields FIELD DESCRIPTION Node-Lnk This is the node index number and link type. Link types are: PPP, ENET, 1483. Status Shows the status of the remote node. TxPkts The number of transmitted packets to this remote node. RxPkts The number of received packets from this remote node. Errors The number of error packets on this connection. Tx B/s Shows the transmission rate in bytes per second. Rx B/s Shows the receiving rate in bytes per second. Up Time Time this channel has been connected to the current remote node. My WAN IP (from ISP) The IP address of the ISP remote node. Ethernet Shows statistics for the LAN. 10-2 System Information and Diagnosis Prestige 650 ADSL Router FIELD DESCRIPTION Status Shows the current status of the LAN. Tx Pkts The number of transmitted packets to the LAN. Rx Pkts The number of received packets from the LAN. Collision Number of collisions. WAN Shows statistics for the WAN. Line Status Shows the current status of the xDSL line which can be Up or Down. Downstream Speed Shows the downstream speed of the Prestige in kbps. Upstream Speed Shows the upstream speed of the Prestige in kbps. CPU Load Specifies the percentage of CPU utilization. 10.2 System Information and Console Port Speed This section describes your system and allows you to choose different console port speeds. To get to the System Information and Console Port Speed: Step 1. Enter 24 to display Menu 24 — System Maintenance. Step 2. Enter 2 to display Menu 24.2 — System Information and Console Port Speed. Step 3. From this menu you have two choices as shown in the next figure: Menu 24.2 - System Information and Console Port Speed 1. System Information 2. Console Port Speed Please enter selection: Figure 10-3 Menu 24.2 — System Information and Console Port Speed 10.2.1 System Information Enter 1 in menu 24.2 to display the screen shown next. System Information and Diagnosis 10-3 Prestige 650 ADSL Router Menu 24.2.1 – System Maintenance – Information Name: Routing: IP ZyNOS F/W Version: V3.40(ES.0)b8 | 11/20/2001 ADSL Chipset Vendor: Alcatel, Version 3.8.130 Standard: Multi-Mode LAN Ethernet Address: 00:a0:c5:01:23:45 IP Address: 192.168.1.1 IP Mask: 255.255.255.0 DHCP: Server Press ESC or RETURN to Exit: Figure 10-4 Menu 24.2.1 — System Maintenance — Information Table 10-2 Fields in System Maintenance FIELD DESCRIPTION Name Displays the system name of your Prestige. This information can be changed in Menu 1 – General Setup. Routing Refers to the routing protocol used. ZyNOS F/W Version Refers to the ZyNOS (ZyXEL Network Operating System) system firmware version. ZyNOS is a registered trademark of ZyXEL Communications Corporation. ADSL Chipset Vendor Displays the vendor of the ADSL chipset and DSL version. Standard This refers to the operational protocol the Prestige and the DSLAM (Digital Subscriber Line Access Multiplexer) are using. LAN Ethernet Address IP Address IP Mask DHCP 10-4 Refers to the Ethernet MAC (Media Access Control) of your Prestige. This is the IP address of the Prestige in dotted decimal notation. This shows the subnet mask of the Prestige. This field shows the DHCP setting (None, Relay or Server) of the Prestige. System Information and Diagnosis Prestige 650 ADSL Router 10.2.2 Console Port Speed You can set up different port speeds for the console port through Menu 24.2.2 – System Maintenance – Console Port Speed. Your Prestige supports 9600 (default), 19200 and 38400bps. Use [SPACE BAR] and then [ENTER] to select the desired speed in menu 24.2.2, as shown in the following figure. Menu 24.2.2 – System Maintenance – Change Console Port Speed Console Port Speed: 9600 Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 10-5 Menu 24.2.2 — System Maintenance — Change Console Port Speed 10.3 Log and Trace There are two logging facilities in the Prestige. The first is the error logs and trace records that are stored locally. The second is the UNIX syslog facility for message logging. 10.3.1 Viewing Error Log The first place you should look for clues when something goes wrong is the error log. Follow the procedures to view the local error/trace log: Step 1. Type 24 in the main menu to display Menu 24 – System Maintenance. Step 2. From menu 24, type 3 to display Menu 24.3 – System Maintenance – Log and Trace. Menu 24.3 - System Maintenance - Log and Trace 1. View Error Log 2. UNIX Syslog Please enter selection Figure 10-6 Menu 24.3 — System Maintenance — Log and Trace Step 3. Enter 1 from Menu 24.3 — System Maintenance — Log and Trace to display the error log in the system. After the Prestige finishes displaying the error log, you will have the option to clear it. Samples of typical error and information messages are presented in the next figure. System Information and Diagnosis 10-5 Prestige 650 ADSL Router 59 Thu Jan 01 60 Thu Jan 01 61 Thu Jan 01 62 Thu Jan 01 63 Thu Jan 01 Clear Error Log 00:00:03 00:00:03 00:00:03 00:00:19 00:00:24 (y/n): 1970 1970 1970 1970 1970 PP0f INFO PP00 -WARN PP00 INFO PP00 INFO PP0a WARN LAN promiscuous mode <0> SNMP TRAP 0: cold start main: init completed SMT Session Begin MPOA Link Down Figure 10-7 Sample Error and Information Messages 10.3.2 Syslog and Accounting The Prestige uses the UNIX syslog facility to log the CDR (Call Detail Record) and system messages to a syslog server. Syslog and accounting can be configured in Menu 24.3.2 — System Maintenance — UNIX Syslog, as shown next. Menu 24.3.2 - System Maintenance - UNIX Syslog UNIX Syslog: Active= No Syslog IP Address= ? Log Facility= Local 1 Types: CDR= No Packet triggered= No Filter Log= No PPP Log= No Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 10-8 Menu 24.3.2 — System Maintenance — Syslog and Accounting You need to configure the UNIX syslog parameters described in the following table to activate syslog then choose what you want to log. Table 10-3 System Maintenance Menu — Syslog Parameters FIELD DESCRIPTION UNIX Syslog: Active Syslog IP Address 10-6 Use [SPACE BAR] and then [ENTER] to turn syslog on or off. Type the IP address of your syslog server. System Information and Diagnosis Prestige 650 ADSL Router FIELD DESCRIPTION Log Facility Use [SPACE BAR] and then [ENTER] to select one of seven different local options. The log facility lets you log the message in different server files. Refer to your UNIX manual. Types: CDR Packet Triggered Call Detail Record (CDR) logs all data phone line activity if set to Yes. The first 48 bytes or octets and protocol type of the triggering packet is sent to the UNIX syslog server when this field is set to Yes. Filter Log No filters are logged when this field is set to No. Filters with the individual filter Log Filter field set to Yes are logged when this field is set to Yes. PPP Log PPP events are logged when this field is set to Yes. The following are examples of the four types of syslog messages sent by the Prestige: 1 - CDR SdcmdSyslogSend ( SYSLOG_CDR, SYSLOG_INFO, String); String = board xx line xx channel xx, call xx, str board = the hardware board ID line = the WAN ID in a board Channel = channel ID within the WAN call = the call reference number which starts from 1 and increments by 1 for each new call str = C01 Outgoing Call dev xx ch xx (dev:device No. ch:channel No.) C01 Incoming Call xxxxBps xxxxx (L2TP, xxxxx = Remote Call ID) C01 Incoming Call xxxx (= connected speed) xxxxx (= Remote Call ID) L02 Tunnel Connected (L2TP) C02 OutCall Connected xxxx (= connected speed) xxxxx (= Remote Call ID) C02 CLID call refused L02 Call Terminated C02 Call Terminated Jul 19 11:19:27 192.168.102.2 ZYXEL: board 0 line 0 channel 0, call 1, C01 Outgoing Call dev=2 ch=0 40002 Jul 19 11:19:32 192.168.102.2 ZYXEL: board 0 line 0 channel 0, call 1, C02 OutCall Connected 64000 40002 Jul 19 11:20:06 192.168.102.2 ZYXEL: board 0 line 0 channel 0, call 1, C02 Call Terminated 2 - Packet Triggered SdcmdSyslogSend (SYSLOG_PKTTRI, SYSLOG_NOTICE, String); String = Packet trigger: Protocol=xx Data=xxxxxxxxxx…..x Protocol: (1:IP 2:IPX 3:IPXHC 4:BPDU 5:ATALK 6:IPNG) Data: We will send forty-eight Hex characters to the server Jul 19 11:28:39 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=4500003c100100001f010004c0a86614ca849a7b08004a5c020001006162636465666768696a6b6c6d6e6f70717273 74 Jul 19 11:28:56 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=4500002c1b0140001f06b50ec0a86614ca849a7b0427001700195b3e00000000600220008cd40000020405b4 Jul 19 11:29:06 192.168.102.2 ZYXEL: Packet Trigger: Protocol=1, Data=45000028240140001f06ac12c0a86614ca849a7b0427001700195b451d1430135004000077600000 3 - Filter Log SdcmdSyslogSend (SYSLOG_FILLOG, SYSLOG_NOTICE, String); String = IP[Src=xx.xx.xx.xx Dst=xx.xx.xx.xx prot spo=xxxx dpo=xxxx] S04>R01mD IP[…] is the packet header and S04>R01mD means filter set 4 (S) and rule 1 (R), match (m), drop (D). System Information and Diagnosis 10-7 Prestige 650 ADSL Router Src: Source Address Dst: Destination Address prot: Protocol (“TCP”, ”UDP”, ”ICMP”) spo: Source port dpo: Destination port Jul 19 14:43:55 192.168.102.2 ZYXEL: IP [Src=202.132.154.123 Dst=255.255.255.255 UDP spo=0208 dpo=0208]} S03>R01mF Jul 19 14:44:00 192.168.102.2 ZYXEL: IP [Src=192.168.102.20 Dst=202.132.154.1 UDP spo=05d4 dpo=0035]} S03>R01mF Jul 19 14:44:04 192.168.102.2 ZYXEL: IP [Src=192.168.102.20 Dst=202.132.154.1 UDP spo=05d4 dpo=0035]} S03>R01mF 4 - PPP Log SdcmdSyslogSend (SYSLOG_PPPLOG, SYSLOG_NOTICE, String); String = ppp:Proto Starting / ppp:Proto Opening / ppp:Proto Closing / ppp:Proto Shutdown Proto = LCP / ATCP / BACP / BCP / CBCP / CCP / CHAP/ PAP / IPCP / IPXCP Jul 19 11:42:44 192.168.102.2 ZYXEL: ppp:LCP Closing Jul 19 11:42:49 192.168.102.2 ZYXEL: ppp:IPCP Closing Jul 19 11:42:54 192.168.102.2 ZYXEL: ppp:CCP Closing 10.4 Diagnostic The diagnostic facility allows you to test the different aspects of your Prestige to determine if it is working properly. Menu 24.4 allows you to choose among various types of diagnostic tests to evaluate your system, as shown in the following figure. Menu 24.4 - System Maintenance – Diagnostic System 21. Reboot System 22. Command Mode xDSL 1. Reset xDSL 5. TCP/IP 12. Ping Host Enter Menu Selection Number: Host IP Address= N/A Figure 10-9 Menu 24.4 — System Maintenance — Diagnostic Follow the procedure next to get to Diagnostic: Step 1. From the main menu, type 24 to open Menu 24 – System Maintenance. Step 2. From this menu, type 4. Diagnostic to open Menu 24.4 – System Maintenance – Diagnostic. The following table describes the diagnostic tests available in menu 24.4 for and the connections. Table 10-4 System Maintenance Menu — Diagnostic FIELD Reset xDSL 10-8 DESCRIPTION Re-initialize the xDSL link to the telephone company. System Information and Diagnosis Prestige 650 ADSL Router FIELD DESCRIPTION Ping Host Ping the host to see if the links and TCP/IP protocol on both systems are working. Reboot System Reboot the Prestige. Command Mode Type the mode to test and diagnose your Prestige using specified commands. Host IP Address If you typed 12 to Ping Host, now type the address of the computer you want to ping. System Information and Diagnosis 10-9 Prestige 650 ADSL Router Chapter 11 Firmware and Configuration File Maintenance This chapter tells you how to back up and restore your configuration file as well as upload new firmware and a new configuration file. 11.1 Filename Conventions The configuration file (often called the romfile or rom-0) contains the factory default settings in the menus such as password, DHCP Setup, TCP/IP Setup, etc. It arrives from ZyXEL with a “rom” filename extension. Once you have customized the Prestige's settings, they can be saved back to your computer under a filename of your choosing. ZyNOS (ZyXEL Network Operating System sometimes referred to as the “ras” file) is the system firmware and has a “bin” filename extension. With many FTP and TFTP clients, the filenames are similar to those seen next. ftp> put firmware.bin ras This is a sample FTP session showing the transfer of the computer file " firmware.bin" to the Prestige. ftp> get rom-0 config.cfg This is a sample FTP session saving the current configuration to the computer file “config.cfg”. If your (T)FTP client does not allow you to have a destination filename different than the source, you will need to rename them as the Prestige only recognizes “rom-0” and “ras”. Be sure you keep unaltered copies of both files for later use. The following table is a summary. Please note that the internal filename refers to the filename on the Prestige and the external filename refers to the filename not on the Prestige, that is, on your computer, local network or FTP site and so the name (but not the extension) may vary. After uploading new firmware, see the ZyNOS F/W Version field in Menu 24.2.1 — System Maintenance — Information to confirm that you have uploaded the correct firmware version. The AT command is the command you enter after you press “y” when prompted in the SMT menu to go into debug mode. Firmware and Configuration File Maintenance 11-1 Prestige 650 ADSL Router Table 11-1 Filename Conventions FILE TYPE INTERNAL NAME EXTERNAL NAME DESCRIPTION Configuration File Rom-0 This is the configuration filename on the Prestige. Uploading the rom-0 file replaces the entire ROM file system, including your Prestige configurations, system-related data (including the default password), the error log and the trace log. *.rom Firmware Ras This is the generic name for the ZyNOS firmware on the Prestige. *.bin 11.2 Backup Configuration The Prestige displays different messages explaining different ways to backup, restore and upload files in menus 24.5, 24.6, 24. 7.1 and 24.7.2; depending on whether you use the console port or Telnet. Option 5 from Menu 24 — System Maintenance allows you to backup the current Prestige configuration to your computer. Backup is highly recommended once your Prestige is functioning properly. FTP is the preferred methods for backing up your current configuration to your computer since they are faster. You can also perform backup and restore using menu 24 through the console port. Any serial communications program should work fine; however, you must use Xmodem protocol to perform the download/upload and you don’t have to rename the files. Please note that terms “download” and “upload” are relative to the computer. Download means to transfer from the Prestige to the computer, while upload means from your computer to the Prestige. 11-2 Firmware and Configuration File Maintenance Prestige 650 ADSL Router 11.2.1 Backup Configuration Follow the instructions as shown in the next screen. Menu 24.5 - System Maintenance - Backup Configuration To transfer the configuration file to your workstation, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your router. Then type "root" and SMT password as requested. 3. Locate the 'rom-0' file. 4. Type 'get rom-0' to back up the current router configuration to your workstation. For details on FTP commands, please consult the documentation of your FTP client program. For details on backup using TFTP (note that you must remain in this menu to back up using TFTP), please see your router manual. Press ENTER to Exit: Figure 11-1 Telnet in Menu 24.5 11.2.2 Using the FTP Command from the Command Line Step 1. Launch the FTP client on your computer. Step 2. Enter “open”, followed by a space and the IP address of your Prestige. Step 3. Press [ENTER] when prompted for a username. Step 4. Enter your password as requested (the default is “1234”). Step 5. Enter “bin” to set transfer mode to binary. Step 6. Use “get” to transfer files from the Prestige to the computer, for example, “get rom-0 config.rom” transfers the configuration file on the Prestige to your computer and renames it “config.rom”. See earlier in this chapter for more information on filename conventions. Step 7. Enter “quit” to exit the ftp prompt. 11.2.3 Example of FTP Commands from the Command Line Firmware and Configuration File Maintenance 11-3 Prestige 650 ADSL Router 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> get rom-0 zyxel.rom 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 16384 bytes sent in 1.10Seconds 297.89Kbytes/sec. ftp> quit Figure 11-2 FTP Session Example 11.2.4 GUI-based FTP Clients The following table describes some of the commands that you may see in GUI-based FTP clients. Table 11-2 General Commands for GUI-based FTP Clients COMMAND DESCRIPTION Host Address Enter the address of the host server. Login Type Anonymous. This is when a user I.D. and password is automatically supplied to the server for anonymous access. Anonymous logins will work only if your ISP or service administrator has enabled this option. Normal. The server requires a unique User ID and Password to login. Transfer Type Transfer files in either ASCII (plain text format) or in binary mode. Initial Remote Directory Specify the default remote directory (path). Initial Local Directory Specify the default local directory (path). 11.2.5 TFTP and FTP over WAN Will Not Work When TFTP, FTP and Telnet over WAN will not work when: 1. You have disable Telnet service in menu 24.11. 2. You have applied a filter in menu 3.1 (LAN) or in menu 11.5 (WAN) to block Telnet service. 3. The IP address in the Secured Client IP field in menu 24.11 does not match the client IP. If it does not match, the Prestige will disconnect the Telnet session immediately. 11-4 Firmware and Configuration File Maintenance Prestige 650 ADSL Router 4. You have an SMT console session running. 11.2.6 Backup Configuration Using TFTP The Prestige supports the up/downloading of the firmware and the configuration file using TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should work over WAN as well, it is not recommended. To use TFTP, your computer must have both telnet and TFTP clients. To backup the configuration file, follow the procedure shown next. Step 1. Use telnet from your computer to connect to the Prestige and log in. Because TFTP does not have any security checks, the Prestige records the IP address of the telnet client and accepts TFTP requests only from this address. Step 2. Put the SMT in command interpreter (CI) mode by entering 8 in Menu 24 — System Maintenance. Step 3. Enter command “sys stdio 0” to disable the SMT timeout, so the TFTP transfer will not be interrupted. Enter command “sys stdio 5” to restore the five-minute SMT timeout (default) when the file transfer is complete. Step 4. Launch the TFTP client on your computer and connect to the Prestige. Set the transfer mode to binary before starting data transfer. Step 5. Use the TFTP client (see the example below) to transfer files between the Prestige and the computer. The file name for the configuration file is “rom-0” (rom-zero, not capital o). Note that the telnet connection must be active and the SMT in CI mode before and during the TFTP transfer. For details on TFTP commands (see following example), please consult the documentation of your TFTP client program. For UNIX, use “get” to transfer from the Prestige to the computer and “binary” to set binary transfer mode. 11.2.7 TFTP Command Example The following is an example TFTP command: tftp [-i] host get rom-0 config.rom where “i” specifies binary image transfer mode (use this mode when transferring binary files), “host” is the Prestige IP address, “get” transfers the file source on the Prestige (rom-0, name of the configuration file on the Prestige) to the file destination on the computer and renames it config.rom. 11.2.8 GUI-based TFTP Clients The following table describes some of the fields that you may see in GUI-based TFTP clients. Table 11-3 General Commands for GUI-based TFTP Clients Firmware and Configuration File Maintenance 11-5 Prestige 650 ADSL Router COMMAND DESCRIPTION Host Enter the IP address of the Prestige. 192.168.1.1 is the Prestige’s default IP address when shipped. Send/Fetch Use “Send” to upload the file to the Prestige and “Fetch” to back up the file on your computer. Local File Enter the path and name of the firmware file (*.bin extension) or configuration file (*.rom extension) on your computer. Remote File This is the filename on the Prestige. The filename for the firmware is “ras” and for the configuration file, is “rom-0”. Binary Transfer the file in binary mode. Abort Stop transfer of the file. Refer to section 11.2.5 to read about configurations that disallow TFTP and FTP over WAN. 11.2.9 Backup Via Console Port Back up configuration via console port by following the HyperTerminal procedure shown next. Procedures using other serial communications programs should be similar. Step 1. Display menu 24.5 and enter “y” at the following screen. Ready to backup Configuration via Xmodem. Do you want to continue (y/n): Figure 11-3 System Maintenance — Backup Configuration Step 2. The following screen indicates that the Xmodem download has started. You can enter ctrl-x to terminate operation any time. Starting XMODEM download... Figure 11-4 System Maintenance — Starting Xmodem Download Screen 11-6 Firmware and Configuration File Maintenance Prestige 650 ADSL Router Step 3. Run the HyperTerminal program by clicking Transfer, then Receive File as shown in the following screen. Type a location for storing the configuration file or click Browse to look for one. Choose the Xmodem protocol. Then click Receive. Figure 11-5 Backup Configuration Example Step 4. After a successful backup you will see the following screen. Press any key to return to the SMT menu. ** Backup Configuration completed. OK. ### Hit any key to continue.### Figure 11-6 Successful Backup Confirmation Screen 11.3 Restore Configuration This section shows you how to restore a previously saved configuration. Note that this function erases the current configuration before restoring a previous back up configuration; please do not attempt to restore unless you have a backup configuration file stored on disk. FTP is the preferred method for restoring your current computer configuration to your Prestige since FTP is faster. Please note that you must wait for the system to automatically restart after the file transfer is complete. Firmware and Configuration File Maintenance 11-7 Prestige 650 ADSL Router WARNING! DO NOT INTERUPT THE FILE TRANSFER PROCESS AS THIS MAY PERMANENTLY DAMAGE YOUR PRESTIGE. WHEN THE RESTORE CONFIGURATION PROCESS IS COMPLETE, THE PRESTIGE WILL AUTOMATICALLY RESTART. 11.3.1 Restore Using FTP For details about backup using (T)FTP please refer to earlier sections on FTP and TFTP file upload in this chapter. Menu 24.6 -- System Maintenance - Restore Configuration To transfer the firmware and configuration file to your workstation, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your router. Then type "root" and SMT password as requested. 3. Type "put backupfilename rom-0" where backupfilename is the name of your backup configuration file on your workstation and rom-0 is the remote file name on the router. This restores the configuration to your router. 4. The system reboots automatically after a successful file transfer For details on FTP commands, please consult the documentation of your FTP client program. For details on backup using TFTP (note that you must remain in this menu to back up using TFTP), please see your router manual. Press ENTER to Exit: Figure 11-7 Telnet into Menu 24.6 Step 1. Launch the FTP client on your computer. Step 2. Enter “open”, followed by a space and the IP address of your Prestige. Step 3. Press [ENTER] when prompted for a username. Step 4. Enter your password as requested (the default is “1234”). Step 5. Enter “bin” to set transfer mode to binary. Step 6. Find the “rom” file (on your computer) that you want to restore to your Prestige. 11-8 Firmware and Configuration File Maintenance Prestige 650 ADSL Router Step 7. Use “put” to transfer files from the Prestige to the computer, for example, “put config.rom rom0” transfers the configuration file “config.rom” on your computer to the Prestige. See earlier in this chapter for more information on filename conventions. Step 8. Enter “quit” to exit the ftp prompt. The Prestige will automatically restart after a successful restore process. 11.3.2 Restore Using FTP Session Example ftp> put config.rom rom-0 200 Port command okay 150 Opening data connection for STOR rom-0 226 File received OK 221 Goodbye for writing flash ftp: 16384 bytes sent in 0.06Seconds 273.07Kbytes/sec. ftp>quit Figure 11-8 Restore Using FTP Session Example Refer to section 11.2.5 to read about configurations that disallow TFTP and FTP over WAN. 11.3.3 Restore Via Console Port Restore configuration via console port by following the HyperTerminal procedure shown next. Procedures using other serial communications programs should be similar. Step 1. Display menu 24.6 and enter “y” at the following screen. Ready to restore Configuration via Xmodem. Do you want to continue (y/n): Figure 11-9 System Maintenance — Restore Configuration Step 2. The following screen indicates that the Xmodem download has started. Starting XMODEM download (CRC mode) ... CCCCCCCCC Figure 11-10 System Maintenance — Starting Xmodem Download Screen Step 3. Run the HyperTerminal program by clicking Transfer, then Send File as shown in the following screen. Firmware and Configuration File Maintenance 11-9 Prestige 650 ADSL Router Type the configuration file’s location, or click Browse to search for it. Choose the Xmodem protocol. Then click Send. Figure 11-11 Restore Configuration Example Step 4. After a successful restoration you will see the following screen. Press any key to restart the Prestige and return to the SMT menu. Save to ROM Hit any key to start system reboot. Figure 11-12 Successful Restoration Confirmation Screen 11.4 Uploading Firmware and Configuration Files This section shows you how to upload firmware and configuration files. You can upload configuration files by following the procedure in the previous Restore Configuration section or by following the instructions in Menu 24.7.2 — System Maintenance — Upload System Configuration File (for console port). WARNING! DO NOT INTERUPT THE FILE TRANSFER PROCESS AS THIS MAY PERMANENTLY DAMAGE YOUR PRESTIGE. 11.4.1 Firmware File Upload FTP is the preferred method for uploading the firmware and configuration. To use this feature, your computer must have an FTP client. When you telnet into the Prestige, you will see the following screens for uploading firmware and the configuration file using FTP. 11-10 Firmware and Configuration File Maintenance Prestige 650 ADSL Router Menu 24.7.1 - System Maintenance - Upload System Firmware To upload the system firmware, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your system. Then type "root" and SMT password as requested. 3. Type "put firmwarefilename ras" where "firmwarefilename" is the name of your firmware upgrade file on your workstation and "ras" is the remote file name on the system. 4. The system reboots automatically after a successful firmware upload. For details on FTP commands, please consult the documentation of your FTP client program. For details on uploading system firmware using TFTP (note that you must remain on this menu to upload system firmware using TFTP), please see your manual. Press ENTER to Exit: Figure 11-13 Telnet Into Menu 24.7.1 — Upload System Firmware 11.4.2 Configuration File Upload You see the following screen when you telnet into menu 24.7.2. Menu 24.7.2 - System Maintenance - Upload System Configuration File To upload the system configuration file, follow the procedure below: 1. Launch the FTP client on your workstation. 2. Type "open" and the IP address of your system. Then type "root" and SMT password as requested. 3. Type "put configurationfilename rom-0" where "configurationfilename" is the name of your system configuration file on your workstation, which will be transferred to the "rom-0" file on the system. 4. The system reboots automatically after the upload system configuration file process is complete. For details on FTP commands, please consult the documentation of your FTP client program. For details on uploading system firmware using TFTP (note that you must remain on this menu to upload system firmware using TFTP), please see your manual. Press ENTER to Exit: Figure 11-14 Telnet Into Menu 24.7.2 — System Maintenance Firmware and Configuration File Maintenance 11-11 Prestige 650 ADSL Router To upload the firmware and the configuration file, follow these examples 11.4.3 FTP File Upload Command from the DOS Prompt Example Step 1. Launch the FTP client on your computer. Step 2. Enter “open”, followed by a space and the IP address of your Prestige. Step 3. Press [ENTER] when prompted for a username. Step 4. Enter your password as requested (the default is “1234”). Step 5. Enter “bin” to set transfer mode to binary. Step 6. Use “put” to transfer files from the computer to the Prestige, for example, “put firmware.bin ras” transfers the firmware on your computer (firmware.bin) to the Prestige and renames it “ras”. Similarly, “put config.rom rom-0” transfers the configuration file on your computer (config.rom) to the Prestige and renames it “rom-0”. Likewise “get rom-0 config.rom” transfers the configuration file on the Prestige to your computer and renames it “config.rom.” See earlier in this chapter for more information on filename conventions. Step 7. Enter “quit” to exit the ftp prompt. 11.4.4 FTP Session Example of Firmware File Upload 331 Enter PASS command Password: 230 Logged in ftp> bin 200 Type I OK ftp> put firmware.bin ras 200 Port command okay 150 Opening data connection for STOR ras 226 File received OK ftp: 1103936 bytes sent in 1.10Seconds 297.89Kbytes/sec. ftp> quit Figure 11-15 FTP Session Example of Firmware File Upload More commands (found in GUI-based FTP clients) are listed earlier in this chapter. Refer to section 11.2.5 to read about configurations that disallow TFTP and FTP over WAN. 11.4.5 TFTP File Upload The Prestige also supports the uploading of firmware files using TFTP (Trivial File Transfer Protocol) over LAN. Although TFTP should work over WAN as well, it is not recommended. 11-12 Firmware and Configuration File Maintenance Prestige 650 ADSL Router To use TFTP, your computer must have both telnet and TFTP clients. To transfer the firmware and the configuration file, follow the procedure shown next. Step 1. Use telnet from your computer to connect to the Prestige and log in. Because TFTP does not have any security checks, the Prestige records the IP address of the telnet client and accepts TFTP requests only from this address. Step 2. Put the SMT in command interpreter (CI) mode by entering 8 in Menu 24 – System Maintenance. Step 3. Enter the command “sys stdio 0” to disable the console timeout, so the TFTP transfer will not be interrupted. Enter “command sys stdio 5” to restore the five-minute console timeout (default) when the file transfer is complete. Step 4. Launch the TFTP client on your computer and connect to the Prestige. Set the transfer mode to binary before starting data transfer. Step 5. Use the TFTP client (see the example below) to transfer files between the Prestige and the computer. The file name for the firmware is “ras”. Note that the telnet connection must be active and the Prestige in CI mode before and during the TFTP transfer. For details on TFTP commands (see following example), please consult the documentation of your TFTP client program. For UNIX, use “get” to transfer from the Prestige to the computer, “put” the other way around, and “binary” to set binary transfer mode. 11.4.6 TFTP Upload Command Example The following is an example TFTP command: tftp [-i] host put firmware.bin ras where “i” specifies binary image transfer mode (use this mode when transferring binary files), “host” is the Prestige’s IP address and “put” transfers the file source on the computer (firmware.bin – name of the firmware on the computer) to the file destination on the remote host (ras - name of the firmware on the Prestige). Commands that you may see in GUI-based TFTP clients are listed earlier in this chapter. 11.4.7 Uploading Via Console Port FTP or TFTP are the preferred methods for uploading firmware to your Prestige. However, in the event of your network being down, uploading files is only possible with a direct connection to your Prestige via the console port. Uploading files via the console port under normal conditions is not recommended since FTP or TFTP is faster. Any serial communications program should work fine; however, you must use the Xmodem protocol to perform the download/upload. Firmware and Configuration File Maintenance 11-13 Prestige 650 ADSL Router 11.4.8 Uploading Firmware File Via Console Port Step 1. Select 1 from Menu 24.7 — System Maintenance — Upload Firmware to display Menu 24.7.1 — System Maintenance — Upload System Firmware, then follow the instructions as shown in the following screen. Menu 24.7.1 - System Maintenance - Upload System Firmware To 1. 2. 3. upload system firmware: Enter "y" at the prompt below to go into debug mode. Enter "atur" after "Enter Debug Mode" message. Wait for "Starting XMODEM upload" message before activating Xmodem upload on your terminal. 4. After successful firmware upload, enter "atgo" to restart the router. Warning: Proceeding with the upload will erase the current system firmware. Do You Wish To Proceed:(Y/N) Figure 11-16 Menu 24.7.1 as seen using the Console Port Step 2. After the "Starting Xmodem upload" message appears, activate the Xmodem protocol on your computer. Follow the procedure as shown previously for the HyperTerminal program. The procedure for other serial communications programs should be similar. 11.4.9 Example Xmodem Firmware Upload Using HyperTerminal Click Transfer, then Send File to display the following screen. Type the firmware file’s location, or click Browse to look for it. Choose the Xmodem protocol. Then click Send. Figure 11-17 Example Xmodem Upload After the firmware upload process has completed, the Prestige will automatically restart. 11-14 Firmware and Configuration File Maintenance Prestige 650 ADSL Router 11.4.10 Step 1. Uploading Configuration File Via Console Port Select 2 from Menu 24.7 — System Maintenance — Upload Firmware to display Menu 24.7.2 — System Maintenance — Upload System Configuration File. Follow the instructions as shown in the next screen. Menu 24.7.2 - System Maintenance - Upload System Configuration File To 1. 2. 3. upload system configuration file: Enter "y" at the prompt below to go into debug mode. Enter "atlc" after "Enter Debug Mode" message. Wait for "Starting XMODEM upload" message before activating Xmodem upload on your terminal. 4. After successful firmware upload, enter "atgo" to restart the system. Warning: 1. Proceeding with the upload will erase the current configuration file. 2. The system’s console port speed (Menu 24.2.2) may change when it is restarted; please adjust your terminal's speed accordingly. The password may change (menu 23), also. 3. When uploading the DEFAULT configuration file, the console port speed will be reset to 9600 bps and the password to "1234". Do You Wish To Proceed:(Y/N) Figure 11-18 Menu 24.7.2 as seen using the Console Port Step 2. After the "Starting Xmodem upload" message appears, activate the Xmodem protocol on your computer. Follow the procedure as shown previously for the HyperTerminal program. The procedure for other serial communications programs should be similar. Step 3. Enter “atgo” to restart the Prestige. 11.4.11 Example Xmodem Configuration Upload Using HyperTerminal Click Transfer, then Send File to display the following screen. Firmware and Configuration File Maintenance 11-15 Prestige 650 ADSL Router Type the configuration file’s location, or click Browse to search for it. Choose the Xmodem protocol. Then click Send. Figure 11-19 Example Xmodem Upload After the configuration upload process has completed, restart the Prestige by entering “atgo”. 11-16 Firmware and Configuration File Maintenance Prestige 650 ADSL Router Chapter 12 System Maintenance and Information This chapter leads you through SMT menus 24.8 to 24.10. 12.1 Command Interpreter Mode The Command Interpreter (CI) is a part of the main system firmware. The CI provides much of the same functionality as the SMT, while adding some low-level setup and diagnostic functions. Enter the CI from the SMT by selecting menu 24.8. Access can be by Telnet or by a serial connection to the console port, although some commands are only available with a serial connection. See the included disk or the zyxel.com web site for more detailed information on CI commands. Enter 8 from Menu 24 — System Maintenance. A list of valid commands can be found by typing help or ? at the command prompt. Type “exit” to return to the SMT main menu when finished. Menu 24 - System Maintenance 1. System Status 2. System Information and Console Port Speed 3. Log and Trace 4. Diagnostic 5. Backup Configuration 6. Restore Configuration 7. Firmware Update 8. Command Interpreter Mode Figure 12-1 Command Mode in Menu 24 System Maintenance and Information 12-1 Prestige 650 ADSL Router Copyright (c) 1994 - 2002 ZyXEL Communications Corp. ras> ? Valid commands are: sys exit ether wan ip bridge show set ras> Figure 12-2 Valid Commands 12.2 Call Control Support The Prestige provides the budget management call control function. Please note that this menu is only applicable when Encapsulation is set to PPPoE or PPPoA in menu 4 or menu 11.1. The budget management function allows you to set a limit on the total outgoing call time of the Prestige within certain times. When the total outgoing call time exceeds the limit, the current call will be dropped and any future outgoing calls will be blocked. To access the call control menu, select option 9 in menu 24 to go to Menu 24.9 — System Maintenance — Call Control, as shown in the next table. Menu 24.9 - System Maintenance - Call Control 1. Budget Management Enter Menu Selection Number: Figure 12-3 Call Control 12.2.1 Budget Management Menu 24.9.1 shows the budget management statistics for outgoing calls. Enter 1 from Menu 24.9 — System Maintenance — Call Control to bring up the following menu. 12-2 System Maintenance and Information Prestige 650 ADSL Router Menu 24.9.1 - Budget Management Remote Node 1.ChangeMe 2.-------3.-------4.-------5.-------6.-------7.-------8.-------- Connection Time/Total Budget No Budget --------------- Elapsed Time/Total Period No Budget --------------- Reset Node (0 to update screen): Figure 12-4 Budget Management The total budget is the time limit on the accumulated time for outgoing calls to a remote node. When this limit is reached, the call will be dropped and further outgoing calls to that remote node will be blocked. After each period, the total budget is reset. The default for the total budget is 0 minutes and the period is 0 hours, meaning no budget control. You can reset the accumulated connection time in this menu by entering the index of a remote node. Enter 0 to update the screen. The budget and the reset period can be configured in menu 11.1 for the remote node when PPPoE encapsulation is selected. Table 12-1 Budget Management FIELD DESCRIPTION EXAMPLE Remote Node Enter the index number of the remote node you want to reset (just one in this case) 1 Connection Time/Total Budget This is the total connection time that has gone by (within the allocated budget that you set in menu 11.1. 5/10 means that 5 minutes out of a total allocation of 10 minutes have lapsed. Elapsed Time/Total Period The period is the time cycle in hours that the allocation budget is reset (see menu 11.1.) The elapsed time is the time used up within this period. 0.5/1 means that 30 minutes out of the 1 hour time period has lapsed. Enter “0” to update the screen or press [ESC] to return to the previous screen. System Maintenance and Information 12-3 Prestige 650 ADSL Router 12.3 Time and Date Setting The Prestige keeps track of the time and date. There is also a software mechanism to set the time manually or get the current time and date from an external server when you turn on your Prestige. Menu 24.10 allows you to update the time and date settings of your Prestige. The real time is then displayed in the Prestige error logs and firewall logs. Select menu 24 in the main menu to open Menu 24 — System Maintenance, as shown next. Menu 24 - System Maintenance 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. System Status System Information and Console Port Speed Log and Trace Diagnostic Backup Configuration Restore Configuration Upload Firmware Command Interpreter Mode Call Control Time and Date Setting Remote Management Enter Menu Selection Number: Figure 12-5 Menu 24 — System Maintenance Then enter 10 to go to Menu 24.10 — System Maintenance — Time and Date Setting to update the time and date settings of your Prestige as shown in the following screen. Menu 24.10 - System Maintenance - Time and Date Setting Use Time Server when Bootup= None Time Server Address= N/A Current Time: New Time (hh:mm:ss): 00 : 00 : 00 11 : 23 : 16 Current Date: New Date (yyyy-mm-dd): 2000 - 01 - 01 2001 - 03 - 01 Time Zone= GMT Daylight Saving= No Start Date (mm-dd): End Date (mm_dd): 01 – 00 01 – 00 Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 12-6 Menu 24.10 System Maintenance — Time and Date Setting 12-4 System Maintenance and Information Prestige 650 ADSL Router Table 12-2 Time and Date Setting Fields FIELD DESCRIPTION Use Time Server when Bootup Enter the time service protocol that your time server sends when you turn on the Prestige. Not all time servers support all protocols, so you may have to check with your ISP/network administrator or use trial and error to find a protocol that works. The main differences between them are the format. Daytime (RFC 867) format is day/month/year/time zone of the server. Time (RFC-868) format displays a 4-byte integer giving the total number of seconds since 1970/1/1 at 0:0:0. NTP (RFC-1305) is similar to Time (RFC-868). None. The default, enter the time manually. Time Server Address Enter the IP address or domain name of your time server. Check with your ISP/network administrator if you are unsure of this information. Current Time This field displays an updated time only when you reenter this menu. New Time Enter the new time in hour, minute and second format. Current Date This field displays an updated date only when you re-enter this menu. New Date Enter the new date in year, month and day format. Time Zone Press [SPACE BAR] and then [ENTER] to set the time difference between your time zone and Greenwich Mean Time (GMT). Daylight Saving If you use daylight savings time, then choose Yes. Start Date If using daylight savings time, enter the month and day that it starts on. End Date If using daylight savings time, enter the month and day that it ends on Once you have filled in this menu, press [ENTER] at the message “Press ENTER to Confirm or ESC to Cancel“ to save your configuration, or press [ESC] to cancel. 12.3.1 Resetting the Time The Prestige resets the time in three instances: i. On leaving menu 24.10 after making changes. ii. When the Prestige starts up, if there is a time server configured in menu 24.10. iii. 24-hour intervals after starting. System Maintenance and Information 12-5 Prestige 650 ADSL Router Chapter 13 IP Policy Routing This chapter covers setting and applying policies used for IP routing. 13.1 Introduction Traditionally, routing is based on the destination address only and the IAD takes the shortest path to forward a packet. IP Routing Policy (IPPR) provides a mechanism to override the default routing behavior and alter the packet forwarding based on the policy defined by the network administrator. Policy-based routing is applied to incoming packets on a per interface basis, prior to the normal routing. 13.2 Benefits • Source-Based Routing – Network administrators can use policy-based routing to direct traffic from different users through different connections. • Quality of Service (QoS) – Organizations can differentiate traffic by setting the precedence or TOS (Type of Service) values in the IP header at the periphery of the network to enable the backbone to prioritize traffic. • Cost Savings – IPPR allows organizations to distribute interactive traffic on high-bandwidth, high-cost paths while using low-cost paths for batch traffic. • Load Sharing – Network administrators can use IPPR to distribute traffic among multiple paths. 13.3 Routing Policy Individual routing policies are used as part of the overall IPPR process. A policy defines the matching criteria and the action to take when a packet meets the criteria. The action is taken only when all the criteria are met. The criteria includes the source address and port, IP protocol (ICMP, UDP, TCP, etc.), destination address and port, TOS and precedence (fields in the IP header) and length. The inclusion of length criterion is to differentiate between interactive and bulk traffic. Interactive applications, for example, telnet, tend to have short packets, while bulk traffic, for example, file transfer, tends to have large packets. The actions that can be taken include: • routing the packet to a different gateway (and hence the outgoing interface). • setting the TOS and precedence fields in the IP header. IP Policy Routing 13-1 Prestige 650 ADSL Router IPPR follows the existing packet filtering facility of RAS in style and in implementation. The policies are divided into sets, where related policies are grouped together. A user defines the policies before applying them to an interface or a remote node, in the same fashion as the filters. There are 12 policy sets with six policies in each set. 13.4 IP Routing Policy Setup Menu 25 shows all the policies defined. Menu 25 - IP Routing Policy Setup Policy Policy Set # Name Set # Name ------ ----------------- ------ ----------------- 1 test 7 _______________ 2 _______________ 8 _______________ 3 _______________ 9 _______________ 4 _______________ 10 _______________ 5 _______________ 11 _______________ 6 _______________ 12 _______________ Figure 13-1 IP Routing Policy Setup To setup a routing policy, perform the following procedures: Step 1. Type 25 in the main menu to open Menu 25 – IP Routing Policy Setup. Step 2. Type the index of the policy set you want to configure to open Menu 25.1 – IP Routing Policy Setup. Menu 25.1 shows the summary of a policy set, including the criteria and the action of a single policy, and whether a policy is active or not. Each policy contains two lines. The former part is the criteria of the incoming packet and the latter is the action. Between these two parts, separator “|” means the action is taken on criteria matched and separator “=” means the action is taken on criteria not matched. 13-2 IP Policy Routing Prestige 650 ADSL Router Menu 25.1 - IP Routing Policy Setup # A Criteria/Action - - -------------------------------------------------------------------------1 Y SA=1.1.1.1-1.1.1.1,DA=2.2.2.2-2.2.2.5 SP=20-25,DP=20-25,P=6,T=NM,PR=0 |GW=192.168.1.1,T=MT,PR=0 2 N __________________________________________________________________________ __________________________________________________________________________ 3 N __________________________________________________________________________ __________________________________________________________________________ Figure 13-2 Menu 25.1 — Sample IP Routing Policy Setup Table 13-1 IP Routing Policy Setup ABBREVIATION Criterion SA Source IP Address SP Source Port DA Destination IP Address DP Destination Port P IP layer 4 protocol number (TCP=6, UDP=17…) T Type of service of incoming packet PR Action Service IP Policy Routing MEANING GW Precedence of incoming packet Gateway IP address T Outgoing Type of service P Outgoing Precedence NM Normal MD Minimum Delay MT Maximum Throughput MR Maximum Reliability MC Minimum Cost 13-3 Prestige 650 ADSL Router Type a number from 1 to 6 to display Menu 25.1.1 – IP Routing Policy (see the next figure). This menu allows you to configure a policy rule. Menu 25.1.1 - IP Routing Policy Policy Set Name= test Active= Yes Criteria: IP Protocol = 6 Type of Service= Normal Precedence = 0 Source: addr start= 1.1.1.1 port start= 20 Destination: addr start= 2.2.2.2 port start= 20 Action= Matched Gateway addr = 192.168.1.1 Type of Service= Max Thruput Precedence = 0 Packet length= 40 Len Comp= N/A end= 1.1.1.1 end= 20 end= 2.2.2.2 end= 20 Log= No Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 13-3 IP Routing Policy Table 13-2 IP Routing Policy FIELD DESCRIPTION Policy Set Name This is the policy set name assigned in Menu 25 – IP Routing Policy Setup. Active Press [SPACE BAR] and then [ENTER] to select Yes to activate the policy. Criteria: IP Protocol Type of Service Prioritize incoming network traffic by choosing from Don’t Care, Normal, Min Delay, Max Thruput, Min Cost or Max Reliable. Precedence Precedence value of the incoming packet. Press [SPACE BAR] and then [ENTER] to select a value from 0 to 7 or Don’t Care. Packet Length Type the length of incoming packets (in bytes). The operators in the Len Comp (next field) apply to packets of this length. Len Comp 13-4 IP layer 4 protocol, for example, UDP, TCP, ICMP, etc. Press [SPACE BAR] and then [ENTER] to choose from Equal, Not Equal, Less, Greater, Less or Equal or Greater or Equal. IP Policy Routing Prestige 650 ADSL Router FIELD DESCRIPTION Source: addr start / end Source IP address range from start to end. port start / end Source port number range from start to end; applicable only for TCP/UDP. Destination: addr start / end Destination IP address range from start to end. port start / end Destination port number range from start to end; applicable only for TCP/UDP. Action Specifies whether action should be taken on criteria Matched or Not Matched. Gateway addr Defines the outgoing gateway address. The gateway must be on the same subnet as the Prestige if it is on the LAN, otherwise, the gateway must be the IP address of a remote node. The default gateway is specified as 0.0.0.0. Type of Service Set the new TOS value of the outgoing packet. Prioritize incoming network traffic by choosing No Change, Normal, Min Delay, Max Thruput, Max Reliable or Min Cost. Precedence Set the new outgoing packet precedence value. Values are 0 to 7 or No Change. Log Press [SPACE BAR] and then [ENTER] to select Yes to make an entry in the system log when a policy is executed. When you have completed this menu, press [ENTER] at the prompt “Press [ENTER] to confirm or [ESC] to cancel” to save your configuration or press [ESC] to cancel and go back to the previous screen. 13.5 Applying an IP Policy This section shows you where to apply the IP policies after you design them. 13.5.1 Ethernet IP Policies From Menu 3 — Ethernet Setup, type 2 to go to Menu 3.2 — TCP/IP and DHCP Ethernet Setup. You can choose up to four IP policy sets (from 12) by typing their numbers separated by commas, for example, 2, 4, 7, 9. IP Policy Routing 13-5 Prestige 650 ADSL Router Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup: DHCP= None Client IP Pool Starting Address= N/A Size of Client IP Pool= N/A Primary DNS Server= N/A Secondary DNS Server= N/A Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-2B Multicast= IGMP-v2 IP Policies= 2,4,7,9 Edit IP Alias= No Type IP Policy sets here. Press ENTER to Confirm or ESC to Cancel: Figure 13-4 Menu 3.2 — TCP/IP and DHCP Ethernet Setup Go to menu 11.3 (shown next) and type the number(s) of the IP Routing Policy set(s) as appropriate. You can cascade up to four policy sets by typing their numbers separated by commas. Menu 11.3 - Remote Node Network Layer Options IP Options: IP Address Assignment= Static Bridge Options: Ethernet Addr Timeout (min)= 0 Rem IP Addr: 0.0.0.0 Rem Subnet Mask= 0.0.0.0 My WAN Addr= 0.0.0.0 NAT= Full Feature Address Mapping Set= 2 Metric= 2 Type IP Policy sets here. Figure 13-5 Menu 11.3 — Remote Node Network Layer Options 13.6 IP Policy Routing Example If a network has both Internet and remote node connections, you can route Web packets to the Internet using one policy and route FTP packets to a remote network using another policy. See the next figure. 13-6 IP Policy Routing Prestige 650 ADSL Router Figure 13-6 Example of IP Policy Routing To force Web packets coming from clients with IP addresses of 192.168.1.33 to 192.168.1.64 to be routed to the Internet via the WAN port of the Prestige, follow the steps as shown next. IP Policy Routing 13-7 Prestige 650 ADSL Router Step 1. Create a routing policy set in menu 25. Step 2. Create a rule for this set in Menu 25.1.1 — IP Routing Policy as shown next. Menu 25.1.1 - IP Routing Policy Policy Set Name= set1 Active= Yes Criteria: IP Protocol = 6 Type of Service= Don't Care Precedence = Don't Care Source: addr start= 192.168.1.2 port start= 0 Destination: addr start= 0.0.0.0 port start= 80 Action= Matched Gateway addr = 192.168.1.1 Type of Service= No Change Precedence = No Change Packet length= 10 Len Comp= N/A end= 192.168.1.64 end= N/A end= N/A end= 80 Log= No Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 13-7 IP Routing Policy Example Step 3. Check Menu 25.1 — IP Routing Policy Setup to see if the rule is added correctly. Step 4. Create another policy set in menu 25. Step 5. Create a rule in menu 25.1 for this set to route packets from any host (IP=0.0.0.0 means any host) with protocol TCP and port FTP access through another gateway (192.168.1.100). 13-8 IP Policy Routing Prestige 650 ADSL Router Menu 25.1.1 - IP Routing Policy Policy Set Name= set2 Active= Yes Criteria: IP Protocol = 6 Type of Service= Don't Care Precedence = Don't Care Source: addr start= 0.0.0.0 port start= 0 Destination: addr start= 0.0.0.0 port start= 20 Action= Matched Gateway addr =192.168.1.100 Type of Service= No Change Precedence = No Change Packet length= 10 Len Comp= N/A end= N/A end= N/A end= N/A end= 21 Log= No Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 13-8 IP Routing Policy Step 6. Check Menu 25.1 — IP Routing Policy Setup to see if the rule is added correctly. Step 7. Apply both policy sets in menu 3.2 as shown next. Menu 3.2 - TCP/IP and DHCP Ethernet Setup DHCP Setup DHCP= Server Client IP Pool Starting Address= 192.168.1.33 Size of Client IP Pool= 64 Primary DNS Server= 0.0.0.0 Secondary DNS Server= 0.0.0.0 Remote DHCP Server= N/A TCP/IP Setup: IP Address= 192.168.1.1 IP Subnet Mask= 255.255.255.0 RIP Direction= Both Version= RIP-1 Multicast= None IP Policies= 1,2 Edit IP Alias= No Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle. Figure 13-9 Applying IP Policies IP Policy Routing 13-9 Prestige 650 ADSL Router Chapter 14 Call Scheduling Call scheduling (applicable for PPPoE and PPPoA encapsulation only) allows you to dictate when a remote node should be called and for how long. 14.1 Introduction The call scheduling feature allows the Prestige to manage a remote node and dictate when a remote node should be called and for how long. This feature is similar to the scheduler in a video cassette recorder (you can specify a time period for the VCR to record). You can apply up to 4 schedule sets in Menu 11.1 — Remote Node Profile. From the main menu, enter 26 to access Menu 26 — Schedule Setup as shown next. Menu 26 - Schedule Setup Schedule Set # -----1 2 3 4 5 6 Name ----------------______________ ______________ ______________ ______________ ______________ ______________ Schedule Set # -----7 8 9 10 11 12 Name -----------------______________ ______________ ______________ ______________ ______________ ______________ Enter Schedule Set Number to Configure= Edit Name= Figure 14-1 Menu 26 — Schedule Setup Lower numbered sets take precedence over higher numbered sets thereby avoiding scheduling conflicts. For example, if sets 1, 2 ,3 and 4 in are applied in the remote node then set 1 will take precedence over set 2, 3 and 4 as the Prestige, by default, applies the lowest numbered set first. Set 2 will take precedence over set 3 and 4, and so on. You can design up to 12 schedule sets but you can only apply up to four schedule sets for a remote node. Call Scheduling 14-1 Prestige 650 ADSL Router To delete a schedule set, enter the set number and press [SPACE BAR] and then [ENTER] (or delete) in the Edit Name field. To setup a schedule set, select the schedule set you want to setup from menu 26 (1-12) and press [ENTER] to see Menu 26.1 — Schedule Set Setup as shown next. Menu 26.1 - Schedule Set Setup Active= Yes Start Date(yyyy/mm/dd) = 2000 – 01 - 01 How Often= Once Once: Date(yyyy/mm/dd)= 2000 – 01 - 01 Weekdays: Sunday= N/A Monday= N/A Tuesday= N/A Wednesday= N/A Thursday= N/A Friday= N/A Saturday= N/A Start Time (hh:mm)= 00 : 00 Duration (hh:mm)= 00 : 00 Action= Forced On Press ENTER to Confirm or ESC to Cancel: Press Space Bar to Toggle Figure 14-2 Schedule Set Setup If a connection has been already established, your Prestige will not drop it. Once the connection is dropped manually or it times out, then that remote node can't be triggered up until the end of the Duration. Table 14-1 Schedule Set Setup Fields FIELD DESCRIPTION EXAMPLE Active Press [SPACE BAR] to select Yes or No. Choose Yes and press [ENTER] to activate the schedule set. Yes Start Date Enter the start date when you wish the set to take effect in year month-date format. Valid dates are from the present to 2036February-5. 2000-01-01 How Often Should this schedule set recur weekly or be used just once only? Press the [SPACE BAR] and then [ENTER] to select Once or Weekly. Both these options are mutually exclusive. If Once is selected, then all weekday settings are N/A. When Once is Once 14-2 Call Scheduling Prestige 650 ADSL Router FIELD DESCRIPTION EXAMPLE How Often Should this schedule set recur weekly or be used just once only? Press the [SPACE BAR] and then [ENTER] to select Once or Weekly. Both these options are mutually exclusive. If Once is selected, then all weekday settings are N/A. When Once is selected, the schedule rule deletes automatically after the scheduled time elapses. Once Once: If you selected Once in the How Often field above, then enter the date the set should activate here in year-month-date format. 2000-01-01 If you selected Weekly in the How Often field above, then select the day(s) when the set should activate (and recur) by going to that day(s) and pressing [SPACE BAR] to select Yes, then press [ENTER]. Yes Start Time Enter the start time when you wish the schedule set to take effect in hour-minute format. 09:00 Duration Enter the maximum length of time this connection is allowed in hour-minute format. 08:00 Action Forced On means that the connection is maintained whether or not there is a demand call on the line and will persist for the time period specified in the Duration field. Date Weekday: Day No N/A Forced On Forced Down means that the connection is blocked whether or not there is a demand call on the line. Enable Dial-On-Demand means that this schedule permits a demand call on the line. Disable Dial-On-Demand means that this schedule prevents a demand call on the line. When you have completed this menu, press [ENTER] at the prompt “Press ENTER to Confirm…” to save your configuration, or press [ESC] at any time to cancel. Once your schedule sets are configured, you must then apply them to the desired remote node(s). Enter 11 from the Main Menu and then enter the target remote node index. Using [SPACE BAR], select PPPoE or PPPoA in the Encapsulation field and then press [ENTER] to make the schedule sets field available as shown next. Call Scheduling 14-3 Prestige 650 ADSL Router Menu 11.1 - Remote Node Profile Rem Node Name= ChangeMe Active= Yes Route= IP Bridge= No Encapsulation= PPPoE Multiplexing=VC-based Service Name= Incoming Rem Login= Rem Password= ******** Edit IP/Bridge= No Edit ATM Options= No Telco Option: Allocated Budget(min)= 0 Period(hr)= 0 Outgoing= My Login=? My Password= ******** Authen= CHAP/PAP Schedules= 1,2,3,4 Nailed-Up Connection= No Session Options: Edit Filter Sets= No Idle Timeout(sec)= 100 Press ENTER to Confirm or ESC to Cancel: Apply your schedule sets here. Press Space Bar to Toggle. Figure 14-3 Applying Schedule Set(s) to a Remote Node (PPPoE) You can apply up to four schedule sets, separated by commas, for one remote node. Change the schedule set numbers to your preference(s). 14-4 Call Scheduling Prestige 650 ADSL Router Chapter 15 Remote Management This chapter covers remote management (SMT menu 24.11). 15.1 Telnet The only way to configure the Prestige for remote management is through an SMT session using the console port. Once your Prestige is configured, you can use Telnet to configure it remotely as shown next. Figure 15-1 Telnet Configuration on a TCP/IP Network 15.2 FTP You can upload and download Prestige firmware and configuration files using FTP - please see System Information and Diagnosis chapter for details. To use this feature, your computer must have an FTP client. 15.3 Web You can use the Prestige’s embedded web configurator for configuration and file management. See the Read Me First to learn how to access the web configurator. 15.4 Remote Management To disable remote management of a service, select Disable in the corresponding Server Access field. Enter 11 from menu 24 to display Menu 24.11 — Remote Management. Remote Management 15-1 Prestige 650 ADSL Router 15.4.1 Remote Management Setup Remote management setup is for managing Telnet, FTP and Web services. You can customize the service port, access interface and the secured client IP address to enhance security and flexibility. You may manage your Prestige from a remote location via: the Internet (WAN only), the LAN only, All (LAN and WAN) or Disable (neither). WAN only (Internet) ALL (LAN and WAN) LAN only Disable (Neither) If you enable remote management of a service, but have applied a filter to block the service, then you will not be able to remotely manage the service. Enter 11, from menu 24, to display Menu 24.11 — Remote Management Control (shown next). Menu 24.11 - Remote Management Control TELNET Server: Port = 23 Access = LAN only Secured Client IP = 0.0.0.0 FTP Server: Port = 21 Access = LAN only Secured Client IP = 0.0.0.0 Web Server: Port = 80 Access = LAN only Secured Client IP = 0.0.0.0 Press ENTER to Confirm or ESC to Cancel: Figure 15-2 Menu 24.11 — Remote Management Control Table 15-1 Menu 24.11 — Remote Management Control FIELD DESCRIPTION EXAMPLE Telnet Server FTP Server Web Server Each of these read-only labels denotes a service that you may use to remotely manage the Prestige. Port This field shows the port number for the remote management service. You may change the port number for a service if needed, but you must use the same port number to use that service for remote management. 23 Access Select the access interface (if any) by pressing the [SPACE BAR]. Choices are: LAN only, WAN only, All or Disable. LAN only (Default) 15-2 Remote Management Prestige 650 ADSL Router FIELD Secured Client IP DESCRIPTION EXAMPLE The default 0.0.0.0 allows any client to use this service to remotely manage the Prestige. Enter an IP address to restrict access to a client with a matching IP address. 0.0.0.0 Once you have filled in this menu, press [ENTER] at the message "Press ENTER to Confirm or ESC to Cancel" to save your configuration, or press [ESC] to cancel. 15.4.2 Remote Management Limitations Remote management over LAN or WAN will not work when: 1. A filter in menu 3.1 (LAN) or in menu 11.5 (WAN) is applied to block a Telnet, FTP or Web service. 2. You have disabled that service in menu 24.11. 3. The IP address in the Secured Client IP field (menu 24.11) does not match the client IP address. If it does not match, the Prestige will disconnect the session immediately. 4. There is an SMT console session running. 5. There is already another remote management session of the same type (Telnet, FTP or Web) running. You may only have one remote management session of the same type running at one time. 6. There is a web remote management session running with a Telnet session. A Telnet session will be disconnected if you begin a web session; it will not begin if there already is a web session. 15.5 Remote Management and NAT When NAT is enabled: Use the Prestige’s WAN IP address when configuring from the WAN. Use the Prestige’s LAN IP address when configuring from the LAN. 15.6 System Timeout There is a system timeout of five minutes (300 seconds) for either the console port or Telnet/web/FTP connections. Your Prestige will automatically log you out if you do nothing in this timeout period, except when it is continuously updating the status in menu 24.1 or when sys stdio has been changed on the command line. Remote Management 15-3 Additional Information Part: IV ADDITIONAL INFORMATION This part contains Troubleshooting, Appendices and the Index. IV Prestige 650 ADSL Router Chapter 16 Troubleshooting This chapter covers potential problems and the corresponding remedies. 16.1 Problems Starting Up the Prestige Table 16-1 Troubleshooting the Start-Up of Your Prestige PROBLEM CORRECTIVE ACTION None of the LEDs turn on when I turn on the Prestige. Make sure that the Prestige’s power adapter is connected to the Prestige and plugged in to an appropriate power source. Check that the Prestige and the power source are both turned on. I cannot access the Prestige via the console port. 1. Make sure the Prestige is connected to your computer's serial port. If the error persists, you may have a hardware problem. In this case, you should contact your vendor. 2. Make sure the communications program is configured correctly. The communications software should be configured as follows: VT100 terminal emulation. 9600 bps is the default speed on leaving the factory. Try other speeds in case the speed has been changed. No parity, 8 data bits, 1 stop bit, data flow set to none. 16.2 Problems with the LAN Interface Table 16-2 Troubleshooting the LAN Interface PROBLEM Cannot access the Prestige from the LAN. CORRECTIVE ACTION If the 10M/100M LEDs on the front panel are both off, check the Ethernet cable types and connections between your Prestige and computer. Prestige connections to a computer or hub require different Ethernet cable types. Refer to the Rear Panel and Connections section for details. Check for faulty Ethernet cables. Make sure your NIC (Network Interface Card) is installed and functioning properly. Check the TCP/IP configuration on your computer. Make sure that the IP address and the subnet mask of the Prestige and your computer(s) are on the same subnet. Troubleshooting 16-1 Prestige 650 ADSL Router 16.3 Problems with the WAN Interface Table 16-3 Troubleshooting the WAN Interface PROBLEM CORRECTIVE ACTION I cannot get a WAN IP address from the ISP. The WAN IP is provided when the ISP recognizes the user as an authorized user after verifying the MAC address, Host Name or User ID. Find out the verification method used by your ISP. If the ISP checks the host name, enter your computer’s name in the System Name field in Menu 1 — General Setup. If the ISP checks the User ID, make sure that you have entered the correct service type, user name (in the My Login field) and password (in the My Password field) in Menu 4 — Internet Access Setup. I cannot connect to a remote node or ISP. Check menu 4 or menu 11.1 to verify the Encapsulation for the remote node. 16.4 Problems with Internet Access Table 16-4 Troubleshooting Internet Access PROBLEM I cannot access the Internet CORRECTIVE ACTION Verify your settings in menu 3.2 and menu 4. Make sure the Prestige is turned on and connected to the network. If the Prestige’s DSL LED is off, check the cable between the Prestige and the telephone wall jack. Make sure you entered your user name correctly. Your username may be case-sensitive. Internet connection disconnects Check the schedule rules in SMT menu 26. If you use PPPoA or PPPoE encapsulation, check the idle time-out setting in SMT menu 11.5. Contact your ISP. 16-2 Troubleshooting Prestige 650 ADSL Router 16.5 Problems with the Password Table 16-5 Troubleshooting the Password PROBLEM I cannot access the Prestige. CORRECTIVE ACTION The Password and Username fields are case-sensitive. Make sure that you enter the correct password and username using the proper casing. Use the RESET button to restore the factory default configuration file. This will restore all of the factory defaults including the password. Refer to the RESET button section in the User's Guide for details. 16.6 Problems with Telnet Table 16-6 Troubleshooting Telnet PROBLEM I cannot access the Prestige from the LAN or WAN. CORRECTIVE ACTION Refer to the Remote Management Limitations section for scenarios when remote management may not be possible. When NAT is enabled: Use the Prestige’s WAN IP address when configuring from the WAN. Use the Prestige’s LAN IP address when configuring from the LAN. Refer to the Problems with the LAN Interface section for instructions on checking your LAN connection. Refer to the Problems with the WAN Interface section for instructions on checking your WAN connection. Troubleshooting 16-3 Prestige 650 ADSL Router Appendix A PPPoE PPPoE in Action An ADSL modem bridges a PPP session over Ethernet (PPP over Ethernet, RFC 2516) from your PC to an ATM PVC (Permanent Virtual Circuit), which connects to an xDSL Access Concentrator where the PPP session terminates (see the next figure). One PVC can support any number of PPP sessions from your LAN. PPPoE provides access control and billing functionality in a manner similar to dial-up services using PPP. Benefits of PPPoE PPPoE offers the following benefits: 1. It provides you with a familiar dial-up networking (DUN) user interface. 2. It lessens the burden on the carriers of provisioning virtual circuits all the way to the ISP on multiple switches for thousands of users. For GSTN (PSTN and ISDN), the switching fabric is already in place. 3. It allows the ISP to use the existing dial-up model to authenticate and (optionally) to provide differentiated services. Traditional Dial-up Scenario The following diagram depicts a typical hardware configuration where the PCs use traditional dial-up networking. Diagram 1 Single-PC per Router Hardware Configuration PPPoE A Prestige 650 ADSL Router How PPPoE Works The PPPoE driver makes the Ethernet appear as a serial link to the PC and the PC runs PPP over it, while the modem bridges the Ethernet frames to the Access Concentrator (AC). Between the AC and an ISP, the AC is acting as a L2TP (Layer 2 Tunneling Protocol) LAC (L2TP Access Concentrator) and tunnels the PPP frames to the ISP. The L2TP tunnel is capable of carrying multiple PPP sessions. With PPPoE, the VC (Virtual Circuit) is equivalent to the dial-up connection and is between the modem and the AC, as opposed to all the way to the ISP. However, the PPP negotiation is between the PC and the ISP. Prestige as a PPPoE Client When using the Prestige as a PPPoE client, the PCs on the LAN see only Ethernet and are not aware of PPPoE. This alleviates the administrator from having to manage the PPPoE clients on the individual PCs. Diagram 2 Prestige as a PPPoE Client B PPPoE Prestige 650 ADSL Router Appendix B Virtual Circuit Topology ATM is a connection-oriented technology, meaning that it sets up virtual circuits over which end systems communicate. The terminology for virtual circuits is as follows: • Virtual Channel Logical connections between ATM switches • Virtual Path A bundle of virtual channels • Virtual Circuit A series of virtual paths between circuit end points Diagram 3 Virtual Circuit Topology Think of a virtual path as a cable that contains a bundle of wires. The cable connects two points and wires within the cable provide individual circuits between the two points. In an ATM cell header, a VPI (Virtual Path Identifier) identifies a link formed by a virtual path; a VCI (Virtual Channel Identifier) identifies a channel within a virtual path. The VPI and VCI identify a virtual path, that is, termination points between ATM switches. A series of virtual paths make up a virtual circuit. Your service provider should supply you with VPI/VCI numbers. Virtual Circuit Topology C Prestige 650 ADSL Router Appendix C Boot Module Commands When you reboot your Prestige, you will be given a choice to go into debug mode by pressing a key at the prompt shown in the following screen. In debug mode you have access to a series of boot module commands, for example ATUR (for uploading firmware) and ATLC (for uploading the configuration file) already discussed in a previous section. Bootbase Version: V1.02 | 10/11/2001 13:36:19 RAM: Size = 8192 Kbytes DRAM POST: Testing: 8192K OK FLASH: Intel 16M *1 ZyNOS Version: V3.40(ES.0)b8 | 12/4/2001 12:54:08 Press any key to enter debug mode within 3 seconds. Diagram 4 Option to Enter Debug Mode Type "ATHE" to view all available Prestige boot module commands. Some are shown in the next screen. Most commands aid in advanced troubleshooting and should only be used by qualified engineers. Boot Module Commands E Prestige 650 ADSL Router ======= Debug Command Listing ======= AT just answer OK ATHE print help ATBAx change baudrate. 1:38.4k, 2:19.2k, 3:9.6k 4:57.6k 5:115.2k ATENx,(y) set BootExtension Debug Flag (y=password) ATSE show the seed of password generator ATTI(h,m,s) change system time to hour:min:sec or show current time ATDA(y,m,d) change system date to year/month/day or show current date ATDS dump RAS stack ATDT dump Boot Module Common Area ATDUx,y dump memory contents from address x for length y ATRBx display the 8-bit value of address x ATRWx display the 16-bit value of address x ATRLx display the 32-bit value of address x ATGO(x) run program at addr x or boot router ATGR boot router ATGT run Hardware Test Program ATRTw,x,y(,z) RAM test level w, from address x to y (z iterations) ATSH dump manufacturer related data in ROM ATDOx,y download from address x for length y to PC via XMODEM ATTD download router configuration to PC via XMODEM ATUR upload router firmware to flash ROM ATLC upload router configuration file to flash ROM ATXSx xmodem select: x=0: CRC mode(default); x=1: checksum mode ATSS display system registers Diagram 5 Boot Module Commands F Boot Module Commands Prestige 650 ADSL Router Appendix D Power Adapter Specifications NORTH AMERICAN PLUG STANDARDS AC Power Adapter Model DV-121AACS Input Power AC120Volts/60Hz/23W Output Power AC12Volts/1.0A Power Consumption 10 W Safety Standards UL, CUL (UL 1310, CSA C22.2 No.223) EUROPEAN PLUG STANDARDS AC Power Adapter Model DV-121AACUP-5716 Input Power AC230Volts/50Hz/19W Output Power AC12Volts/1.0A Power Consumption 10 W Safety Standards TUV, CE (EN 61558) CHINESE PLUG STANDARDS AC Power Adapter Model DV-121AACCP-5720 Input Power AC220Volts/50Hz/18W Output Power AC12Volts/1.0A Power Consumption 10 W Safety Standards CCEE (GB8898) Boot Module Commands G Prestige 650 ADSL Router Appendix E TCP/IP All computers must have a 10M or 100M Ethernet adapter card and TCP/IP installed. Use straight-through Ethernet cables to connect your computer's Ethernet adapter to a hub or switch and to connect the hub or switch to the Prestige's LAN port. Otherwise, connect your computer's Ethernet adapter directly to the LAN port with a crossover Ethernet cable. Windows 95/98/Me/NT/2000/XP, Macintosh OS 7 and later operating systems and all versions of UNIX/LINUX include the software components you need to install and use TCP/IP on your computer. Windows 3.1 requires the purchase of a third-party TCP/IP application package. TCP/IP should already be installed on computers using Windows NT/2000/XP, Macintosh OS 7 and later operating systems. After the appropriate TCP/IP components are installed, configure the TCP/IP settings in order to "communicate" with your network. Setting up Your Windows 95/98/Me Computer Installing TCP/IP Components 1. Click Start, Settings, Control Panel and double-click the Network icon. The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks. If you need the adapter: a. In the Network window, click Add. b. Select Adapter and then click Add. c. Select the manufacturer and model of your network adapter and then click OK. If you need TCP/IP: a. In the Network window, click Add. b. Select Protocol and then click Add. c. Select Microsoft from the list of manufacturers. d. Select TCP/IP from the list of network protocols and then click OK. If you need Client for Microsoft Networks: a. TCP/IP Click Add. I Prestige 650 ADSL Router b. Select Client and then click Add. c. Select Microsoft from the list of manufacturers. d. Select Client for Microsoft Networks from the list of network clients and then click OK. e. Restart your computer so the changes you made take effect. Configuring TCP/IP 1. In the Network window Configuration tab, select your network adapter's TCP/IP entry and click Properties. 2. Click the IP Address tab. -If your IP address is dynamic, select Obtain an IP address automatically. -If you have a static IP address, select Specify an IP address and type your information into the IP Address and Subnet Mask fields. 3. Click the DNS Configuration tab. -If you do not know your DNS information, select Disable DNS. -If you know your DNS information, select Enable DNS and type the information in the fields below (you may not need to fill them all in). 4. Click the Gateway tab. -If you were not given a gateway IP address, remove previously installed gateways. -If you have a gateway IP address, type it in the New gateway field and click Add. 5. Click OK to save and close the TCP/IP Properties window. 6. Click OK to close the Network window. Insert the Windows CD if prompted. 7. Turn on your Prestige and restart your computer when prompted. Verifying TCP/IP Properties 1. Click Start and then Run. 2. In the Run window, type "winipcfg" and then click OK to open the IP Configuration window. 3. Select your network adapter. You should see your computer's IP address, subnet mask and default gateway. J TCP/IP Prestige 650 ADSL Router Setting up Your Windows NT/2000 Computer Configuring TCP/IP 1. Click Start, Settings, Network and Dial-up Connections and right-click Local Area Connection or the connection you want to configure and click Properties. 2. Select Internet Protocol (TCP/IP) (you may need to scroll down) and click Properties. 3. The Internet Protocol TCP/IP Properties window opens. -If your IP address is dynamic, click Obtain an IP address automatically. -If you have a static IP address click Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields. 4. In the Internet Protocol TCP/IP Properties window: -Click Obtain DNS server automatically if you do not know your DNS server IP address(es). -If you know your DNS server IP address(es), type them in the Preferred DNS server and Alternate DNS server fields. If you have previously configured DNS servers, click Advanced and then the DNS tab to order them. 5. Click Advanced: -If you do not know your gateway's IP address, remove any previously installed gateways in the IP Settings tab and click OK. 6. Click OK to save and close the Internet Protocol (TCP/IP) Properties window. 7. Click OK to close the Local Area Connection Properties window. 8. Turn on your Prestige and restart your computer (if prompted). Verifying TCP/IP Properties Click Start, Programs, Accessories and then Command Prompt. In the Command Prompt window, type "ipconfig" and then press [ENTER]. The window will display information about your connection-specific DNS suffix, IP Address, Subnet Mask and Default Gateway. Setting up Your Windows XP Computer Configuring TCP/IP 1. Click start, Control Panel, Network and Internet Connections and then Network Connections. 2. Right-click the network connection you want to configure and then click Properties. 3. Under the General tab, select Internet Protocol (TCP/IP) (you may need to scroll down) and click Properties. TCP/IP K Prestige 650 ADSL Router 4. The Internet Protocol TCP/IP Properties window opens. -If you have a dynamic IP address click Obtain an IP address automatically. -If you have a static IP address click Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields. To configure advanced static address settings for a local area connection, click Advanced, and do one or more of the following to configure additional IP addresses: -In the IP Settings tab, in IP addresses, click Add. -In TCP/IP Address, type an IP address in IP address and a subnet mask in Subnet mask, and then click Add. -Repeat the above two steps for each IP address you want to add. -Configure additional default gateways in the IP Settings tab by clicking Add in Default gateways. -In TCP/IP Gateway Address, type the IP address of the default gateway in Gateway. To manually configure a default metric (the number of transmission hops), clear the Automatic metric check box and type a metric in Metric. -Click Add. -Repeat the previous three steps for each default gateway you want to add. -Click OK when finished. 5. In the Internet Protocol TCP/IP Properties window's General tab: -Click Obtain DNS server address automatically if you do not know your DNS server IP address(es). -If you know your DNS server IP address(es), click Use the following DNS server addresses, type them in the Preferred DNS server and Alternate DNS server fields. If you have previously configured DNS servers, click Advanced and then the DNS tab to order them. 6. Click OK to close the Internet Protocol (TCP/IP) Properties window. 7. Click OK to close the Local Area Connection Properties window. 8. Turn on your Prestige and restart your computer (if prompted). Verifying TCP/IP Properties 1. Click Start, All Programs, Accessories and then Command Prompt. 2. In the Command Prompt window, type "ipconfig" and then press [ENTER]. You can also open Network Connections, right-click a network connection, click Status and then click the Support tab. L TCP/IP Prestige 650 ADSL Router Setting up Your Macintosh Computer Configuring TCP/IP Properties 1. Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/IP Control Panel. 2. Select Ethernet from the Connect via list. 3. For dynamically assigned settings, select Using DHCP Server from the Configure: list. 4. For statically assigned settings, do the following: -From the Configure box, select Manually. -Type your IP address in the IP Address box. -Type your subnet mask in the Subnet mask box. -Type the IP address of your Prestige in the Router address box. 5. Close the TCP/IP Control Panel. 6. Click Save if prompted, to save changes to your configuration. 7. Turn on your Prestige and restart your computer (if prompted). Verifying TCP/IP Properties Check your TCP/IP properties in the TCP/IP Control Panel. TCP/IP M Prestige 650 ADSL Router Index A ADSL, what is it?.............................................. xx AT command ................................................. 11-1 Authentication...........................................4-4, 4-5 auto-negotiation ............................................... 1-2 B Back Panel connections description................................ 2-4 Backup ........................................................... 11-2 Bridging Ether Address .............................................. 6-3 Ethernet........................................................ 6-1 Ethernet Addr Timeout ................................ 6-2 Remote Node ............................................... 6-1 Static Route Setup........................................ 6-2 Budget Management ............................. 12-2, 12-3 C Call Control.................................................... 12-2 Call Filtering .................................................... 8-1 Call Filters Built-In......................................................... 8-1 User-Defined ............................................... 8-1 Call Scheduling.............................................. 14-1 Maximum Number of Schedule Sets ......... 14-1 PPPoE ........................................................ 14-3 Precedence ................................................. 14-1 Precedence Example .................See precedence CDR ............................................................... 10-7 CDR (Call Detail Record).............................. 10-6 CHAP............................................................... 4-4 Collision......................................................... 10-3 Command Interpreter Mode........................... 12-1 Command Mode............................................. 10-9 Community ...................................................... 9-2 Computer Name ............................................. 2-13 Index Conditions that prevent TFTP and FTP from working over WAN ................................... 11-4 Connecting the Prestige ................................... 2-4 Connections Additional Requirements............................. 2-4 ADSL Line .................................................. 2-4 Console Port ................................................ 2-4 Power Adapter............................................. 2-4 Rear Panel ................................................... 2-2 Console Port .................................................. 10-3 Copyright .............................................................ii Cost Of Transmission ........................4-7, 5-5, 5-8 Country Code................................................. 10-4 CPU Load ...................................................... 10-3 Customer Support ................................................v D Data Filtering ................................................... 8-1 Device Filter rules.......................................... 8-16 DHCP ..................................................... 1-3, 10-4 Diagnostic...................................................... 10-8 Diagnostic Tools............................................ 10-1 Digital Subscriber Line Access Multiplexer.... 1-6 DNS ................................................................. 3-9 Domain Name................................................ 7-15 Domain Name System ..................................... 3-4 DSL (Digital Subscriber Line)...........................xx DSL, What Is It? ................................................xx DSLAM .........See Digital Subscriber Line Access Multiplexer Dynamic DNS................................ 1-2, 2-14, 2-15 Dynamic Host Configuration Protocol ............ 3-4 DYNDNS Wildcard....................................... 2-14 E Encapsulation..........................1-4, 3-11, 3-15, 4-2 ENET ENCAP........................................... 3-11 PPP ............................................................ 3-12 O Prestige 650 ADSL Router PPP over Ethernet...................................... 3-12 RFC 1483 .................................................. 3-12 Error Log ....................................................... 10-5 Error/Information Messages Sample ....................................................... 10-6 Ethernet Encapsulation .................................. 7-14 Ethernet Traffic.............................................. 8-20 F FCC.................................................................... iii Filename Conventions ................................... 11-1 Filter .............................................................. 2-17 Applying Filters......................................... 8-19 Ethernet traffic........................................... 8-20 Ethernet Traffic ......................................... 8-20 Filter Rules .................................................. 8-7 Filter Structure............................................. 8-4 Generic Filter Rule .................................... 8-14 Remote Node............................................... 4-8 Remote Node Filter ..................................... 4-8 Remote Node Filters.................................. 8-20 Sample ....................................................... 8-18 SUA........................................................... 8-16 TCP/IP Filter Rule....................................... 8-9 Filter Log ....................................................... 10-7 Filter Rule ...................................................... 8-10 Filter Rule Process........................................... 8-3 Filter Rule Setup .............................................. 8-9 Filter Rules Summary Sample ....................................................... 8-19 Filter Set Class ............................................................ 8-9 Filter Set Configuration ................................... 8-4 Filtering .................................................... 8-1, 8-9 Filtering Process Outgoing Packets......................................... 8-2 Frame Relay..................................................... 1-6 Front Panel illustration.................................................... 2-1 FTP ................................................................ 15-3 Restrictions................................................ 15-3 P FTP File Transfer .........................................11-10 FTP Restrictions .............................................11-4 FTP Server......................................................7-21 Full Rate ...........................................................2-5 G Gateway............................................................5-8 Gateway Node ..................................................6-3 General Setup .................................................2-13 H Hidden Menus ................................................2-11 hop count ..........................................................5-5 Hop Count ................................................ 4-7, 5-8 HTTP..............................................................7-15 HyperTerminal program....................... 11-6, 11-9 I IANA........................................................ 3-2, 3-3 Idle Timeout .....................................................4-3 IGMP support ........................................... 4-8, 5-5 Initialization......................................................2-7 Interactive Applications..................................13-1 Internet access ..................................................3-1 Internet Access . xviii, 1-1, 1-2, 1-6, 2-12, 2-17, 31, 3-13, 3-14, 3-15 Internet Access Setup .......................................7-6 Internet Assigned Numbers Authority.. See IANA IP Address ... 3-10, 5-4, 5-7, 6-3, 8-11, 10-4, 10-9, 13-3 IP Address Assignment ..................................3-12 ENET ENCAP ...........................................3-12 PPP or PPPoE.............................................3-12 RFC 1483 ...................................................3-12 IP Alias Setup...................................................3-6 IP Filter...........................................................8-13 Logic Flow .................................................8-12 IP mask...........................................................8-11 IP network number ...........................................3-2 IP Packet.........................................................8-14 IP Policies.......................................................13-5 Index Prestige 650 ADSL Router IP Policy Routing (IPPR)..........................1-3, 3-5 Applying an IP Policy................................ 13-5 Ethernet IP Policies.................................... 13-5 Gateway ..................................................... 13-5 IP Pool.............................................................. 3-4 IP Protocol ..................................................... 13-4 IP Routing Policy ........................................... 13-4 IP Routing Policy (IPPR)............................... 13-1 Benefits...................................................... 13-1 Cost Savings .............................................. 13-1 Criteria ....................................................... 13-1 Load Sharing.............................................. 13-1 Setup .......................................................... 13-2 IP Routing Policy Setup................................. 13-3 IP Static Route ................................................. 5-6 IP Static Route Setup ................................5-6, 5-7 ISDN ................................................................ 2-6 L LAN ............................................................... 10-3 Link type ........................................................ 10-2 LLC-based Multiplexing.................................. 5-2 Log and Trace ................................................ 10-5 Log Facility.................................................... 10-7 Logging Option..................................... 8-11, 8-15 Login................................................................ 4-4 M MAC address ................................................... 6-3 Main Menu..................................................... 2-11 Management Information Base (MIB)............. 9-2 MBS ..............................See Maximum Burst Size Media Access Control...................................... 6-1 Message Logging ........................................... 10-5 Metric.................................................4-7, 5-5, 5-8 Multicast ...................................................4-8, 5-5 Multiplexing LLC-based ................................................. 3-11 VC-based ................................................... 3-11 Multiplexing........................... 1-4, 3-11, 3-15, 4-2 Multiprotocol Encapsulation.......................... 3-12 Index My WAN Address .................................... 4-7, 5-4 N Nailed-Up Connection ..................................... 4-3 NAT............................................................... 8-16 Application .................................................. 7-3 Applying NAT in the SMT Menus.............. 7-6 Configuring ................................................. 7-8 Definitions ................................................... 7-1 Examples ................................................... 7-18 How NAT Works ........................................ 7-2 Mapping Types............................................ 7-4 Non NAT Friendly Application Programs 7-24 Ordering Rules .......................................... 7-11 What NAT does........................................... 7-2 Network Address Translation (NAT) .............. 7-1 Network Management ..................................... 1-4 NIC .................................................................. 2-4 P Packet Error .......................................................... 10-2 Received .................................................... 10-3 Transmitted................................................ 10-3 Packet Triggered............................................ 10-7 Packets ........................................................... 10-2 PAP.................................................................. 4-4 Password...................................2-8, 2-13, 4-4, 9-2 Ping................................................................ 10-9 Point-to-Point.....................................................xx policy-based routing ...................................... 13-1 POTS Splitter................................................... 2-5 PPP .................................................................. 4-2 PPP Encapsulation ........................................... 5-2 PPP Log ................................................ 10-7, 10-8 Precedence ............................................ 13-1, 13-4 Private................................................4-7, 5-5, 5-8 Protocol.......................................................... 8-10 Protocol Filter Rules ...................................... 8-16 Q Prestige 650 ADSL Router Q Quality of Service .......................................... 13-1 R RAS ...................................................... 10-4, 13-2 Rate Receiving................................................... 10-2 Transmission ............................................. 10-2 Related Documentation.................................. xviii Remote DHCP Server.................................... 3-10 Remote Management Limitations.................. 15-3 Remote Management Setup .................. 15-1, 15-2 Remote Node .......................................... 4-1, 10-2 Remote Node Profile ................................... 4-3 Remote Node Setup.............................. 4-1, 4-2 Remote Node Index Number ......................... 10-2 Remote Node Traffic ..................................... 8-21 Required fields............................................... 2-11 RESET Button ................................................. 2-4 Restore Configuration.................................... 11-7 RFC-1483 ........................................................ 4-2 RFC-2364 ................................................. 4-2, 4-4 RIP......... 3-10, 4-7, 5-5. See Routing Information Protocol Routing Information Protocol.......................... 3-3 Direction...................................................... 3-3 Version ........................................................ 3-3 Routing Policy ............................................... 13-1 S Sample IP Addresses ....................................... 5-2 Schedule Sets Duration..................................................... 14-2 SCR..................................... See Sustain Cell Rate Server7-5, 7-9, 7-10, 7-13, 7-14, 7-15, 7-16, 7-19, 7-20, 12-5 Service ................................................................iv setup a schedule ............................................. 14-2 Single User Account ...................................... 3-16 SMT Menu Overview .................................... 2-10 SNMP R Community...................................................9-3 Configuration ...............................................9-2 Get................................................................9-2 Manager .......................................................9-2 MIBs ............................................................9-2 Trap ..............................................................9-2 Trusted Host.................................................9-3 Source-Based Routing ....................................13-1 Splitters.............................................................2-5 Static Route Setup ............................................5-5 Static Routing Topology...................................5-6 STP ...................................................................2-4 SUA..................................................................1-6 SUA (Single User Account) ................... See NAT Subnet Mask ............ 3-2, 3-10, 4-7, 5-4, 5-8, 10-4 Support Disk...................................................xviii Supporting Disk..............................................xviii Syntax Conventions.......................................... xix Syslog .............................................................10-6 Syslog IP Address ..........................................10-6 Syslog Server..................................................10-6 System Console Port Speed ....................................10-5 Diagnostic ..................................................10-8 Log and Trace ............................................10-5 Syslog and Accounting ..............................10-6 System Information....................................10-3 System Status .............................................10-1 System Information ........................................10-3 System Information & Diagnosis ...................10-1 System Maintenance....10-1, 10-3, 11-2, 11-5, 1113, 11-14, 12-1, 12-2, 12-4 System Management Terminal.......................2-11 System Status .................................................10-2 System Timeout..............................................15-3 T TCP/IP.................................. 5-1, 8-16, 10-9, 15-1 TCP/IP Options ................................................5-1 TCP/IP Parameters ...........................................3-2 Telephone Microfilters .....................................2-6 Index Prestige 650 ADSL Router Telnet ............................................................. 15-1 Telnet Configuration ...................................... 15-1 Telnet Under NAT ......................................... 15-1 TFTP and FTP Over WAN .................................. 15-3 Restrictions ................................................ 15-3 TFTP and FTP over WAN Will Not Work When…...................................................... 11-4 TFTP File Transfer....................................... 11-12 TFTP Restrictions .......................................... 11-4 Time and Date Setting........................... 12-4, 12-5 Time Zone...................................................... 12-5 To avoid damage to the Prestige ...................... 2-4 TOS (Type of Service)................................... 13-1 Trace Records ................................................ 10-5 Transfer Rate.................................................. 10-3 Transmission Rates .................................xviii, 1-1 Type of Service .................. 13-1, 13-3, 13-4, 13-5 Index U UNIX Syslog ........................................ 10-5, 10-6 UNIX syslog parameters................................ 10-6 Upload Firmware ......................................... 11-10 V VC-based Multiplexing ............................ 4-2, 5-1 VPI & VCI..................................................... 3-11 X XMODEM protocol....................................... 11-2 XMODEM upload ........................................... 2-9 Z ZyNOS.................................................. 11-1, 11-2 ZyNOS F/W Version ..................................... 11-1 ZyXEL Limited Warranty Note ................................................................iv S
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Encryption : Standard V1.2 (40-bit) User Access : Print, Fill forms, Extract, Assemble, Print high-res Modify Date : 2002:08:12 13:48:59+08:00 Create Date : 2002:08:12 13:43:26+08:00 Page Count : 214 Creation Date : 2002:08:12 13:43:26+08:00 Mod Date : 2002:08:12 13:48:59+08:00 Producer : Acrobat Distiller 5.0.5 (Windows) Author : Derek Rosner Metadata Date : 2002:08:12 13:48:59+08:00 Creator : Derek Rosner Title : P650-13 ADSL over ISDN Router User's Guide Page Mode : UseOutlinesEXIF Metadata provided by EXIF.tools