Alpine CoverPage_UserManual X208U Navigation Software Manual Navi X209 WRA INE W977HD EN

User Manual: alpine X208U - Navigation Software Manual Free User Guide for Alpine GPS, Manual

Open the PDF directly: View PDF PDF.
Page Count: 89

User Manual
Alpine Navigation System
Navigation software for the Alpine Navigation System
English
March 2015, ver. 1.0
2
Table of contents
1 Warnings and safety information ............................................................................................ 5
2 Getting started ........................................................................................................................... 6
2.1 Initial set-up........................................................................................................................................ 6
2.2 Screen controls ................................................................................................................................... 8
2.2.1 Using the buttons and other controls ........................................................................................................... 8
2.2.2 Using the cursor .......................................................................................................................................... 9
2.2.3 Using the keyboard ..................................................................................................................................... 9
2.2.4 Using touch gestures ................................................................................................................................. 10
2.2.5 Manipulating the map ............................................................................................................................... 11
2.3 Navigation view ................................................................................................................................ 13
2.3.1 Streets and roads ....................................................................................................................................... 15
2.3.2 GPS position markers .............................................................................................................................. 16
2.3.3 The planned route ..................................................................................................................................... 16
2.3.4 Turn preview and next street .................................................................................................................... 17
2.3.5 Maneuver icons ........................................................................................................................................ 17
2.3.6 Lane information and signposts ............................................................................................................... 18
2.3.7 Junction view ............................................................................................................................................ 19
2.3.8 Tunnel view .............................................................................................................................................. 19
2.3.9 Freeway services ....................................................................................................................................... 20
2.3.10 3D object types ....................................................................................................................................... 20
2.3.11 Traffic events .......................................................................................................................................... 21
2.4 Navigation menu ............................................................................................................................... 21
3 Using the navigation ................................................................................................................ 24
3.1 Selecting a destination ...................................................................................................................... 24
3.1.1 Using Freeform Search ............................................................................................................................. 24
3.1.2 Selecting an address .................................................................................................................................. 27
3.1.2.1 Entering an address ............................................................................................................................................ 27
3.1.2.2 Selecting a town center ....................................................................................................................................... 29
3.1.2.3 Selecting the midpoint of a street ........................................................................................................................ 29
3.1.2.4 Selecting an intersection in a town ..................................................................................................................... 30
3.1.2.5 Using the ZIP code to select a destination .......................................................................................................... 30
3.1.3 Selecting a Place of Interest ...................................................................................................................... 31
3.1.3.1 Using Quick search categories ........................................................................................................................... 32
3.1.3.2 Searching by category ........................................................................................................................................ 33
3.1.3.3 Searching by name .............................................................................................................................................. 35
3.1.3.4 Finding help nearby ............................................................................................................................................ 37
3
3.1.4 Selecting a Saved Location ....................................................................................................................... 38
3.1.5 Selecting a History item ............................................................................................................................ 39
3.1.6 Entering coordinates ................................................................................................................................. 40
3.1.7 Selecting a location on the map ................................................................................................................ 41
3.1.8 Planning a Multipoint Route ..................................................................................................................... 42
3.2 Checking Route Information and Alternatives ................................................................................. 43
3.3 Checking Traffic Events.................................................................................................................... 44
3.4 Editing the route ............................................................................................................................... 46
3.4.1 Setting a new starting point ....................................................................................................................... 47
3.4.2 Adding an additional destination .............................................................................................................. 48
3.4.3 Modifying the list of destinations ............................................................................................................. 49
3.4.4 Saving the planned route ........................................................................................................................... 49
3.4.5 Deleting the planned route ........................................................................................................................ 50
3.4.6 Selecting a route alternative when planning the route .............................................................................. 51
3.4.7 Selecting a route alternative for an existing route ..................................................................................... 52
3.5 Saving a location .............................................................................................................................. 53
3.5.1 Editing a Saved Location .......................................................................................................................... 54
3.6 Adding an Alert Point ....................................................................................................................... 54
3.7 Running a Simulation ....................................................................................................................... 56
3.8 Off-road navigation .......................................................................................................................... 57
3.8.1 Switching to off-road navigation .............................................................................................................. 57
3.8.2 Selecting the destination in off-road mode ............................................................................................... 57
3.8.3 Navigating in off-road mode ..................................................................................................................... 58
3.9 Updating the navigation software and the maps .............................................................................. 58
4 Reference guide ....................................................................................................................... 60
4.1 Concepts ........................................................................................................................................... 60
4.1.1 2D/3D GPS reception ............................................................................................................................... 60
4.1.2 Natural and TTS voices............................................................................................................................. 60
4.1.3 Road safety cameras and other proximity Alert Points ............................................................................. 60
4.1.4 Route calculation and recalculation .......................................................................................................... 61
4.1.5 Smart Zoom .............................................................................................................................................. 61
4.1.6 Speed limit warning .................................................................................................................................. 62
4.1.7 Historical traffic ........................................................................................................................................ 62
4.1.8 Real-time traffic ........................................................................................................................................ 62
4.1.9 Intelligent navigation ................................................................................................................................ 63
4.1.9.1 Congestion detour on highways .......................................................................................................................... 63
4.1.9.2 Real-time alternative routes ................................................................................................................................ 64
4.1.9.3 Parking around destination ................................................................................................................................ 65
4
4.1.9.4 Hints upon detour ............................................................................................................................................... 65
4.2 Information menu ............................................................................................................................. 66
4.2.1 Where Am I .............................................................................................................................................. 67
4.2.2 Trip Monitor ............................................................................................................................................. 68
4.3 Setup menu........................................................................................................................................ 68
4.3.1 Route preferences ...................................................................................................................................... 70
4.3.1.1 Vehicle profile ..................................................................................................................................................... 70
4.3.1.2 Route Planning Method types ............................................................................................................................. 72
4.3.1.3 Navigation Mode ................................................................................................................................................ 72
4.3.1.4 Road types ........................................................................................................................................................... 72
4.3.2 Sound ........................................................................................................................................................ 73
4.3.3 Warnings ................................................................................................................................................... 75
4.3.4 Navigation View ....................................................................................................................................... 76
4.3.5 Regional .................................................................................................................................................... 78
4.3.6 Display ...................................................................................................................................................... 79
4.3.7 Traffic ....................................................................................................................................................... 80
4.3.8 Trip Monitor ............................................................................................................................................. 81
4.3.9 User Profiles ............................................................................................................................................. 81
5 End-user license agreement .................................................................................................... 82
6 Copyright note ......................................................................................................................... 82
5
1 Warnings and safety information
The navigation system helps you find your way to your destination with the built-in GPS receiver. Alpine
Navigation System does not transmit your GPS position; others cannot track you.
It is important to look at the display only when it is safe to do so. If you are the driver of the vehicle, we
recommend that you plan and review your route before you start your journey. Plan the route before your
departure and stop if you need to change the route.
You must follow the traffic rules. If you deviate from the planned route, Alpine Navigation System changes
the instructions accordingly.
For more information, see the end-user license agreement (page 82).
6
2 Getting started
Alpine Navigation System is optimized for in-car use. You can use it easily by tapping the screen buttons
and the map with your fingertips.
Easy map updates
Update your maps regularly as road networks are continuously evolving all over the world. About 15% of
the roads are changed each year, new ones are built, directions are altered, new speed limits are set, and
many other changes are made.
It is easy to keep the navigation system up-to-date. Go to alpine.naviextras.com to find map updates and
extra content for your navigation system. Use the Toolbox application with your product connected, and
download the new map data.
To update your navigation software and its maps, you need a PC with Internet access and a USB storage
device. For instructions, see:Page 58
Latest Map Guarantee
When you start using the product, you have 30 days to download the latest available map free of charge.
Free Map updates
When you start using the product, you can download new maps in the next 1 year.
2.1 Initial set-up
When using the navigation software for the first time, an initial set-up process starts automatically.
1. Select your preferred language, then tap to confirm your selection. Later you
can change it in Regional settings (page 78).
7
2. Read the end-user license agreement, and tap if you agree with the terms of
use.
3. The Configuration Wizard starts. Tap to continue.
4. Select the language and speaker used for voice guidance messages. Later you can change it in
Regional settings (page 73). Tap to continue.
5. If needed, modify the time format and unit settings. Later you can change them in Regional
settings (page 78). Tap to continue.
6. If needed, modify the default route planning options. Later you can change them in Route
Preferences (page 70). Tap to continue.
8
7. The initial set-up is now complete, tap .
8. A warning appears to draw your attention to the hazards of operating, entering data into or
obtaining data from the Alpine Navigation System during driving or transportsation. After reading it
carefully, tap to enter the navigation view.
Note!
This warning pops up every time you start Alpine Navigation System.
2.2 Screen controls
The following sections describe the functionality and use of buttons, sliders, and other screen controls in
Alpine Navigation System.
2.2.1 Using the buttons and other controls
To operate Alpine Navigation System, tap the buttons on the touch screen.
The Navigation menu may contain several menu items on one or more pages.
You need to confirm selections or changes only if the application needs to be restarted, if it needs to
perform a major reconfiguration, or if you are about to lose some of your data or settings. Otherwise,
9
Alpine Navigation System saves your selections and applies the new settings without confirmation as
soon as you use the controls.
2.2.2 Using the cursor
You can select a map location by tapping the map during navigation.
When a map location is selected, the cursor ( ) appears at the selected point on the map.
The location of the cursor can be used as the destination of the route or a new Alert Point. You can also
search for Places around it or add this location to your saved locations.
You can also select some of the objects on the map. If you tap the map at the icon of a Place or traffic
event, the object is selected, and you can get information about this object or use it as a route point.
2.2.3 Using the keyboard
You can type with your fingertips on the screen keyboards and you can switch between various keyboard
layouts, for example English, Greek or numerical. Only those keyboard buttons are active that can be
used to type a name that is available on the map. The other keys are grayed out.
Action
Function
Switching to another keyboard
layout, for example from an
English keyboard to a Greek
keyboard
Tap and select the new keyboard layout from the list.
Correcting your entry on the
keyboard
Tap to remove the unnecessary character(s).
Tap and hold the button to delete several characters or the entire input
string.
Entering a space, for example
between a first name and a
family name or in multi-word
street names
Tap the button at the bottom center of the screen.
Entering upper and lower case
letters
By default, when entering a text, the first character appears in upper
case while the rest of the text is in lower case. Tap to enter an
upper case letter or tap it twice to turn on Caps Lock. Tap again to use
lower case letters.
Entering numbers and symbols
Tap to switch to a keyboard offering numbers and symbols.
10
Finalizing the keyboard entry
Tap .
Hiding the keyboard
Tap .
2.2.4 Using touch gestures
You usually need to tap the screen only once. However, some useful features can be accessed with other
gestures. See the table below.
Action
Tapping and
holding the screen
Dragging
11
2.2.5 Manipulating the map
If you tap the map anywhere during navigation, the map stops following the current position (the blue
arrow is not locked in a fix position on the screen anymore) and control buttons appear to help you modify
the map view.
You can perform the following actions on the map:
Action
Button(s)
Function
Checking
location
information
No buttons
The top section of the Navigation view shows information about
the selected point (the cursor ).
Moving the map
by dragging
No buttons
Move the map in any direction: tap and hold the map and move
your finger towards the direction you want to move the map.
Zooming in and
out
,
Change how much of the map is displayed on the screen.
Alpine Navigation System uses maps that let you examine the
locations at various zoom levels, always with optimized content. It
always displays street names and other text with the same font
size, never upside-down, and you only see the streets and
objects that you need.
Map scaling has a limit in 3D map view mode. If you zoom out
further, the map switches to 2D view mode.
Tap once to modify the view in a large step, or tap and hold the
button to modify it continuously and smoothly.
Tilting up and
down
,
Change the vertical view angle of the map in 3D mode.
Tap once to modify the view in a large step, or tap and hold the
button to modify it continuously and smoothly.
Rotating left and
right
,
Changes the horizontal view angle of the map.
Tap once to modify the view in a large step, or tap and hold the
button to modify it continuously and smoothly.
12
Changing 2D,
3D, or 2D North
up views
, ,
Switch between the 3D perspective, 2D Heading up, and 2D
North up map view modes. In Heading up mode the map is
rotated so its top always points in the current driving direction.
This is the default orientation in 3D map view mode. In North up
mode, the map faces North.
Checking the
compass
The direction of the compass shows North.
Selecting
additional
options
Open a list of additional features like saving a location, or
searching for Places around the cursor.
Selecting a
destination
Select the cursor location as a new destination. The route is
automatically calculated.
13
2.3 Navigation view
The navigation view is the main screen of Alpine Navigation System that shows the planned route on a
map. Alpine Navigation System works with digital maps which are not simply the computerized versions
of traditional paper maps. Similarly to paper road maps, the 2D mode of digital maps shows you streets
and roads. Elevation is also illustrated in color.
The navigation view displays the following screen buttons, data fields, and route information on the map
during navigation:
Note!
Some buttons, fields, or icons may not be available in your product version.
14
Number
Name
Description
1
Current
position
marker
The current position is displayed as a blue arrow by default. When there is
no GPS position, the current position marker is transparent and it shows your
last known position. See page 16.
2
GPS position
The dot near the arrow shows the GPS position as perceived by the GPS
receiver. See page 16.
3
Planned route
The planned route is displayed as an orange line.
4
Data fields
Three data fields show the following information:
The estimated time of the arrival at the destination
The remaining time of the trip
The remaining distance to the destination.
By tapping and holding it, you can access additional information about the
current trip on a dashboard screen and in the Trip Summary.
You can change the default values in Setup (page 76) or by tapping the area
where the data fields appear.
If you have not selected a destination, you can see your heading instead of
the three data fields.
5
Next turn
preview
It shows the type of the next maneuver and its distance. See page 17.
6
Next street
It displays the name of the next street. See page 17.
If you have not selected a route destination, you can see nearby house
numbers.
7
2D/2D North
up/3D views
You can switch between the 3D perspective, 2D Heading up, and 2D North
up map view modes. In Heading up mode the map is rotated so its top
always points in the current driving direction. This is the default orientation in
3D map view mode. In North up mode, the map faces North.
8
Traffic
It shows traffic-related information. See page 44.
9
Zoom
You can change how much of the map is displayed on the screen. Alpine
Navigation System uses maps that let you zoom in and out on the map. See
Page 11.
10
Lane
information
On multi-lane roads, it shows the lanes ahead and their directions. The
highlighted arrows represent the lanes and direction you need to take. See
page 18.
11
Alert point
warning
It shows the type of the alert points when approaching a road safety camera
or other Alert Points like school zones or railroad crossings. You must make
sure that using this feature is legal in the country where you intend to use it.
See page 75.
12
Speed limit
warning
It shows the current speed limit of the road. See page 75.
15
13
Warning road
sign
It shows warning for the current road (for example, dangers, sharp curves).
See page 75.
14
Signpost
It shows the available destinations and the road numbers. See page 18.
15
Freeway
services
By tapping it, you can check the details of the next few service stations (gas
stations, restaurants) when traveling on a freeway. See page 20.
16
Parking
around
destination
It appears near the destination. By tapping it, you can check the available
parking facilities around your destination. See page 65.
17
Destination
menu
It appears near the destination. By tapping it, you can check the trip
summary, find Places around your final destination, save the current location,
or suspend the navigation.
18
Additional
information
It shows the Freeway services, Parking around destination, or the
Destination menu button if they are available during navigation.
19
Street name
It shows the current street name. By tapping it, you can open the Where Am I
screen. See page 67.
20
3D objects
They display hills, mountains, roads, landmarks, and buildings in 3D.
By pressing the navigation hardkey button, you can open the Navigation menu, where you can reach
other parts of Alpine Navigation System.
If you are approaching a freeway exit or a complex intersection and the needed information exists, the
map is replaced with a 3D view of the junction. See page 19.
When entering a tunnel, the map is replaced with a generic tunnel image. See page 19.
2.3.1 Streets and roads
Alpine Navigation System shows the streets similarly to paper road maps. Their width and colors
correspond to their importance; you can easily tell a freeway from a small street.
16
2.3.2 GPS position markers
When your GPS position is available, Alpine Navigation System marks your current position. By default,
this marker is a blue arrow. The dot near the arrow shows the GPS position as perceived by the GPS
receiver.
When on-road navigation is selected, the current position marker may not show your exact GPS position
and heading. If roads are near, it is aligned to the nearest road to eliminate GPS position errors, and the
direction of the icon is aligned to the direction of the road.
If you select off-road navigation, the current position marker is at your exact GPS position. The direction
of the icon shows your current heading.
2.3.3 The planned route
The planned route is the currently navigated route. Whenever the destination is set, the route is active
until you delete it, reach your destination or suspend navigation. Alpine Navigation System displays the
route in the following ways:
Symbol
Name
Description
Current GPS position
and starting point
It is your current position displayed on the map.
If a vehicle is selected for route calculation and roads are near,
the arrow jumps to the nearest road.
The dot near the arrow shows the exact GPS position.
Normally, if GPS position is available, the route starts from the current
position. If there is no valid GPS position, Alpine Navigation System
uses the last known position as the starting point.
Waypoint (intermediate
destination)
It is an intermediate destination of the route before reaching the final
destination.
Destination (end point)
It is the final destination of the route.
Route color
The route always stands out with its color on the map, both in daytime
and night color modes.
Streets and roads that
are excluded from the
navigation
You can choose whether you want to use or avoid certain road types
(page 70). However, when Alpine Navigation System cannot avoid
such roads, the route includes them and shows them in a color that is
different from the route color.
Streets and roads that
are affected by traffic
events
Road segments may be affected by traffic events. These streets and
roads are displayed in a different color, and small symbols displayed
along the route show the type of the traffic event.
17
2.3.4 Turn preview and next street
When navigating a route, the top section of the Navigation view shows information about the next route
event (maneuver) and the next street or the next town.
There is a field in the top left corner displaying the next maneuver. Both the type of the maneuver (turn,
traffic circle, exiting freeway, and so on) and its distance from the current position are displayed.
A smaller icon shows the type of the second next maneuver if it is near the first one. Otherwise, only the
next maneuver is displayed.
2.3.5 Maneuver icons
During navigation the next maneuver is displayed in the top left corner. Most of the maneuver icons are
intuitive. The following table lists some of the frequently shown route events:
Icon
Function
Turn left.
Turn right.
Turn back.
Bear right.
Turn sharp left.
Keep left.
Continue straight in the intersection.
Enter the traffic circle and take the first exit (next
maneuver).
Enter the traffic circle (second next maneuver).
18
Enter the freeway.
Exit the freeway.
Board the ferry.
Leave the ferry.
Approaching a waypoint on the right.
Approaching the destination.
2.3.6 Lane information and signposts
When navigating on multi-lane roads, it is important to take the appropriate lane in order to follow the
planned route. If lane information is available in the map data, Alpine Navigation System displays the
lanes and their directions using small arrows at the bottom of the map. Highlighted arrows represent the
lanes and the direction you need to take.
Where additional information is available, arrows are replaced by signposts. Signposts are displayed at
the top of the map. The color and style of the signposts are similar to the real ones you can see above
roads or by roadsides. They show the available destinations and the road numbers.
All signposts look similar when cruising (when there is no planned route). During navigation only the
signpost that points to the lane(s) to be taken is highlighted; all the others are darker.
If you want to hide the currently displayed signposts, tap any of them and the normal Navigation view
returns until new signpost information is received.
You can modify the signpost settings in . See page 76.
19
2.3.7 Junction view
If you are approaching a freeway exit or a complex intersection and the needed information exists, the
map is replaced with a 3D view of the junction. The lanes you need to take are displayed with arrows. At
the top of the screen, road signs show you additional information.
If you want to hide the currently displayed junction and return to the Navigation view, tap the picture.
Junction view can be turned off in . See page 76.
2.3.8 Tunnel view
When entering a tunnel, the map is replaced with a generic tunnel image so that surface roads and
buildings cannot distract you.
The top-down overview of the tunnel displayed in a separate window helps you orient yourself. The
remaining distance in the tunnel is also displayed.
After leaving the tunnel, the original map view returns.
Tunnel view can be turned off in . See page 76.
20
2.3.9 Freeway services
When you are driving on a freeway, the button appears at the top right corner of the Navigation
view. Tap it to open a panel with the details of the next few service stations (gas stations, restaurants).
Tap any of them to display the exit area on the map. You can now easily add this service station as a
waypoint to your route if necessary.
If you want to display other types of Places at the next few service stations, you can change the icons in
. See page 76.
2.3.10 3D object types
Alpine Navigation System supports the following 3D object types:
Type
Description
3D terrain
Alpine Navigation System displays 3D hills and mountains in the Navigation view, and
illustrates them by coloring and shading on the 2D map.
Elevated roads
Elevated roads are complex intersections and vertically isolated roads (such as
overpasses or bridges) displayed in 3D.
3D landmarks
Landmarks are 3D representations of prominent or well-known objects.
3D buildings
3D buildings are block representations of full town building data containing actual
building sizes and positions on the map.
21
2.3.11 Traffic events
Road segments affected by traffic events are displayed in a different color on the map.
The following icons may appear at the top right corner of the screen:
Button
Description
It is displayed when traffic events are not received.
It is displayed when traffic events are received but they do not affect the planned route.
It shows the type of the next traffic event with the expected delay.
It shows the type of the next traffic event if it does not cause any delay or the delay is not known.
For more information, see page 44.
2.4 Navigation menu
Press the navigation hardkey button to open the Navigation menu.
22
You can see the following menu options when you are navigating without a planned route:
Button
Function
Select your destination by entering an address or its coordinate, or by selecting a Place, a
Saved Location, or a Saved Route. You can also look up your recent destinations from the
History. When Internet connection is available, the Online Search option can be a further help to
find your destination.
Build your route from one or more route points. You can also plan a route independently of your
current GPS position by setting a new starting point.
Access additional options and check navigation-related information.
Customize the way the navigation software works.
With a planned route, the following menu options are also available:
Button
Function
Add an intermediate destination to your route.
See route alternatives to avoid parts of the route, or to avoid a specific road from your planned
route.
View the route in its full length on the map and check route parameters and route alternatives.
Tap to access additional options, like Simulation or Route Preferences.
Delete your route.
Delete the next waypoint or the whole route.
The following options are also available on many of the menu screens:
Button
Function
Tap the Menu button to return to the main menu.
Check those notifications that contain important information but do not require
immediate action from the users. If there are no notifications, this icon is not
displayed.
23
The More button appears on the screen to display additional features. Tap it to open
the list of additional features on certain screens.
Tap the Back button to return to the previous screen. You can also press and hold
this button to quickly return to the Navigation view from any other screen.
24
3 Using the navigation
By default, Alpine Navigation System calculates routes using the road network of the maps provided with
the product.
You can select the destination and start navigating to it right away (normal navigation) if you need a route
for immediate navigation.
You can also plan a route independently of your current GPS position even without GPS reception. To
achieve this, you need to set a new starting point in the Multipoint Route menu. It also suspends guidance
so that the route is not recalculated when a new position is received. See Page 47.
You can plan routes with multiple destinations by selecting a first and a second destination and adding it
to your route. You can add as many destinations to your route as you like. See Page 42.
You can also use Alpine Navigation System for off-road navigation. See page 57.
The following sections describe how to select a destination, view and modify the route or use navigation-
related features with the help of the touch screen.
3.1 Selecting a destination
You can choose your destination by selecting one of the following options:
Using Freeform Search to search among different destination types at once, see page 24
Entering a full address or a part of an address, for example a street name without a house number,
see page 27
Selecting a Place as your destination, see page 31
Selecting a Saved Location as your destination, see page 38
Selecting a location from the History of previously used destinations, see page 39
Entering the coordinate of the destination, see page 40
Selecting a location on the map, see page 41
Planning a multipoint route, see page 42.
3.1.1 Using Freeform Search
There are several ways to select your destination. You can initiate a separate search for addresses,
Places, Saved Locations, or recent destinations, but the fastest way to search for any of these is to use
Freeform Search.
Perform the following steps to use Freeform Search:
1. Press the navigation hardkey button to access the Navigation menu.
25
2. Tap . You can see the input field at the top of the screen. Right next to it you
can see the search area, the town around which the search is carried out. The default search area
is the area where you are located. For a local search, skip the next step.
3. (optional) To search in a different area, tap the input field with the search area, and start entering
the name of the new search area on the keyboard.
You only need to enter a few letters to get a result. The most likely result appears below the input
field as you enter new letters.
a. If the new search area is in a different country or state, start entering the country/state and
the town.
b. Tap to see the whole list of the matching results.
4. With the proper search area displayed, start entering the name, address, or category of the
destination you are looking for.
5. Tap to switch to the result screen. You can see all the results in the list,
regardless of their type. Addresses, Places, Place categories, Saved Locations, and recent
destinations are mixed in one list. You can immediately select the result you want to use as your
destination or narrow the list of results for only one type (for example, Places).
6. If necessary, tap on the right side of the list and then tap the related button to narrow the list
of search results by type (the number on the related icon shows the number of the matching
results):
26
Tap to see the list of recent destinations with a matching name or address.
Tap to see the list of your saved locations with a matching name.
Tap to see the list of matching addresses.
Tap to see the list of matching Place category names. Scroll the list and select one of
the categories. You get the list of Places in that category ordered by their distance from your
current position.
Tap to see the list of matching Places ordered by their distance from your current
location.
(optional) If your product contains Places from different data providers, you can further
narrow the list by showing the results from one provider only. Look for the provider logos.
Tap one of them to see Places from that provider.
Tap the Online Providers button to start the new search using the Online Search facility.
Wait for the results and select an item from the list.
Tip!
To search for an intersection in the Freeform search, enter the names of the streets
connected by the '&' sign. You do not need to use spaces before and after the separator
character. For example you can find the intersection of Collins Street and Douglas Avenue
by entering strings, like "Collins St & Douglas Ave", "Collins & Douglas", "Col&Doug", etc.
The more precise the input string is, the fewer false results are expected. If you enter
"Collins St&", you get all the intersections of Collins Street and you can select the
appropriate one from the result list.
7. The route is calculated and the map appears showing the entire route, where you can check route
information and route alternatives. Tap to modify the route parameters, or tap
to start your journey.
27
3.1.2 Selecting an address
If you know at least a part of the address, this is the quickest way to select your destination.
Using the same screen, you can find an address by entering the following information:
The exact address, including the house number, see page 27
The center of a town, see page 29
The midpoint of a street, see page 29
An intersection, see page 30
Any of the above, starting the search with the ZIP code, see page 30.
3.1.2.1 Entering an address
To enter an address as the destination, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap .
3. Select the country by performing the following steps:
a. By default, the Alpine Navigation System proposes the country where you are or in case
there is no valid GPS position, the country of the last known position. If needed, tap
.
b. Start entering the first few letters of the country. The names that match the string appear in
a list.
c. To open the list, tap , and select the country.
1. Select a new town or ZIP code by performing the following steps:
a. Tap and start entering the first few letters of the town or the first few
numbers of the ZIP code. The names that match the string appear in a list.
28
b. To open the list, tap , and select the town or ZIP code.
2. Enter the street name and the house number or crossing street by performing the following steps:
a. Start entering the street name on the keyboard. The names that match the string appear in
a list.
b. Tap to open the list of results. Select the street from the list.
c. Enter the house number or crossing street on the keyboard. (To enter letters, tap .)
d. Tap the selected address to finish the address search.
3. The route is calculated and the map appears showing the entire route, where you can check route
information and route alternatives. Tap to modify the route parameters, or tap
to start your journey.
29
3.1.2.2 Selecting a town center
The town center is not the geometric center of the town but an arbitrary point the map creators have
chosen. In towns and villages, it is usually the most important intersection and in larger towns, it is one of
the important intersections.
1. Press the navigation hardkey button to access the Navigation menu.
2. Go to and modify the country as described earlier (page 27), if necessary.
3. Select a new town or ZIP code by performing the following steps:
a. Tap and start entering the first few letters of the town or the first few
numbers of the ZIP code. The names that match the string appear in a list.
b. To open the list, tap , and select the town or ZIP code.
3.1.2.3 Selecting the midpoint of a street
To navigate to the midpoint of a street without entering the house number, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Go to , and select the street name field.
3. Tap and start entering the street name on the keyboard. The names that
match the string appear in a list.
4. Tap to open the list of results. Select the street from the list.
30
5. Instead of entering the house number, tap . The midpoint of the street is
selected as the destination.
3.1.2.4 Selecting an intersection in a town
To navigate to an intersection, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Go to and select the country and town as described earlier.
3. Start entering the street name on the keyboard. The names that match the string appear in a list.
4. Tap to open the list of results. Select the street from the list.
5. Start entering the name of the crossing street (tap to enter letters), or tap
to open the list of results. Select the crossing street from the list.
3.1.2.5 Using the ZIP code to select a destination
You can also select any kind of destination by entering the ZIP code instead of the city name. To select
the ZIP code, perform the following steps:
1. Go to and modify the country as described earlier (page 27), if necessary.
31
2. Tap .
3. Tap to open the numeric keypad and start entering the ZIP code.
4. Tap to open the list of results. Select the ZIP code from the list.
5. Continue the search as described previously (page 27).
3.1.3 Selecting a Place of Interest
You can search for Places of Interest (Places) in the menu.
Using the same screen, you can find a Place by selecting one of the following options:
Finding frequently searched types of Places with the Quick search categories, see page 32
Searching for a Place by its name, see page 35
Searching for a Place by its category, see page 33
In case of emergency, you can also find help nearby, see page 37
32
3.1.3.1 Using Quick search categories
The Quick search feature helps you quickly find the most frequently selected types of Places. Perform the
following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap .
The following Quick search categories appear:
: If a planned route exists, gas stations are searched along the
route.
: If a planned route exists, accommodation is searched around the
destination.
: If a planned route exists, restaurants are searched along the
route.
: If a planned route exists, parking lots are searched around the
destination.
If there is no planned route (destination is not selected), the search is carried out around the
current position. If the current position is not available either (no GPS signal), places are searched
around the last known position.
3. Tap any of the quick search buttons to get an instant list of Places.
4. The Places in the list can be ordered by their distance from the current or last known position, from
the destination, or by the length of the necessary detour. If you need to reorder the list, tap
33
. To filter the list of results by providers, tap and then the provider logo
on the right side of the screen.
5. (optional) If needed, tap to further filter the list of results.
6. Browse the list and tap one of the list items.
7. The route is calculated and the map appears showing the entire route, where you can check route
information and route alternatives. Tap to modify the route parameters, or tap
to start your journey.
3.1.3.2 Searching by category
To search for Places by their categories and subcategories, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap and .
3. Select the area around which you would like to search for the Place by tapping
. By default, the search area is around the current position (or if it is not
available, around the last known position). In this case, the following result list is ordered by the
distance from this position.
Tap to search along the planned route, and not around a given point.
This is useful when you search for a later stopover that results in a minimal detour only,
such as searching for upcoming gas stations or restaurants. (The result list is ordered by the
length of the necessary detour.)
Tap to search for a place around the destination of the planned route.
(The result list is ordered by the distance from the destination.)
34
Tap to search for a place within a selected town. (The result list is
ordered by the distance from the center of the selected town.)
4. (optional) If you have selected , select the town to search in.
5. Select one of the main Place categories (for example, Accommodation), then browse the
subcategories (for example, Hotel or Motel) to find your destination.
6. You can turn the Category View off at any level to list all Places around the selected location or
along the route.
7. (optional) The Places in the list can be ordered by the following criteria:
Name
Their distance from the current or last known position
Their distance from the selected town
Their distance from the destination
The length of the necessary detour.
35
Tap to reorder the list.
To filter the list of results by providers, tap and then the provider logo on the right side of the
screen.
8. Browse the list and tap one of the list items. A full screen map appears with the selected point in
the middle.
9. The process continues the same way as in case of any other search for Places. See page 32.
3.1.3.3 Searching by name
To search for a Place by name, browse the various Place categories, or use the mixture of the two search
types, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap and .
3. Select the area around which you would like to search for the Place. By default, the search area is
around the current position (or if it is not available, around the last known position). In this case,
the result list is ordered by the distance from this position. Tap to select one of
the following search areas:
Tap to search for a place within a selected town. (The result list is
ordered by the distance from the center of the selected town.)
Tap to search for a place around the destination of the planned route.
(The result list is ordered by the distance from the destination.)
Tap to search along the planned route, and not around a given
position. This is useful when you search for a later stopover that results in a minimal detour
only, such as searching for upcoming gas stations or restaurants. (The result list is ordered
by the length of the necessary detour.)
36
4. (optional) If you have selected , select the town to search in.
You can search for the name of a Place in all categories by performing the following steps:
1. Tap . Using the keyboard, start entering the name of the Place or browse in
the categories.
2. After entering a few letters, tap to open the list of Places or Place categories
with names containing the entered character sequence.
3. Browse the list, if necessary, and tap the desired list item. A full screen map appears with the
selected point in the middle. The process continues the same way as in case of any other Places
search. See page 32.
37
3.1.3.4 Finding help nearby
To quickly search for nearby assistance, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap and .
Places in the following pre-set search categories can be searched for around the current position
(or around the last known position if the current position is not available):
: Car repair and roadside assistance services
: Medical and emergency services
: Police stations
: Gas stations
3. Tap any of the quick search buttons to get an instant list of those types of Places.
4. (optional) The Places in the list can be ordered by the following criteria:
By their distance from the current or last known position
By name.
Tap to reorder the list.
5. Browse the list and tap one of the list items. A full screen map appears with the selected point in
the middle.
6. The process continues the same way as in case of any other Places search. See page 32.
38
3.1.4 Selecting a Saved Location
To select a location that you have already saved (page 53), perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap .
3. The list of Saved Locations is displayed. It contains two pre-set categories: Home and Work.
4. Tap the location that you want to set as your destination. If necessary, browse the list to see more
results.
5. (optional) If needed, tap to enable the editing option so that you can rename
the Saved Locations or delete any of them.
6. The route is calculated and the map appears showing the entire route, where you can check route
information and route alternatives. Tap to modify the route parameters, or tap
to start your journey.
39
3.1.5 Selecting a History item
The destinations that you have used earlier appear in the History list. Smart History offers these locations
from your previous destinations, using parameters like the current time of day, the day of week, and the
current location. The more you use the navigation software, the better it can guess your desired
destination. To select a History item, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. To open all the History items, tap . The list of recent destinations appears. The list begins
with the three most likely destinations that are selected based on your previous routes (Smart
History). The rest of the destinations are ordered by the time they were last selected. If necessary,
scroll the list to see earlier destinations.
3. Select a destination from the list.
4. The route is calculated and the map appears showing the entire route, where you can check route
information and route alternatives. Tap to modify the route parameters, or tap
to start your journey.
Three of the Smart History Items are displayed in the History screen for easy access. You can
select one of them as your destination.
40
3.1.6 Entering coordinates
To select a destination by entering its coordinates, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap .
3. You can enter the latitude and longitude values in any of the following formats: decimal degrees,
degrees and decimal minutes, or degrees, minutes and decimal seconds. Tap
.
Tip!
(optional) If necessary, tap then and enter the
coordinate in UTM format.
4. The route is calculated and the map appears showing the entire route, where you can check route
information and route alternatives. Tap to modify the route parameters, or tap
to start your journey.
41
3.1.7 Selecting a location on the map
To select a map location, perform the following steps:
1. Locate your destination on the map. Move and scale the map as necessary.
2. Tap the location that you want to select as your destination. The cursor ( ) appears there.
3. (optional) If needed, tap to list the Places near the selected point or to save
this location.
Tip!
If you already have a planned route, tap and to
add the selected location to your route.
4. Tap to select the cursor as the destination.
5. The route is calculated and the map appears showing the entire route, where you can check route
information and route alternatives. Tap to modify the route parameters, or tap
to start your journey.
42
3.1.8 Planning a Multipoint Route
To build your route destination-by-destination, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. Tap .
3. There is only one line in the list of route points, the starting point of the route, which is normally the
current GPS position.
4. Tap to select the destination.
5. The New Route to... screen appears, where you can select the destination of the route the same
way as described in the previous sections.
6. If needed, you can add further intermediate destinations.
7. To add more route points, tap or tap to change the final
destination. The Add to Route... menu appears again, where you can select the new route point
the same way as you have set the destination before.
43
8. (optional) Tap to optimize the whole route or the order of waypoints. You can
also delete all the destinations.
9. When you have added all the route points, tap and the planned route is
automatically calculated.
3.2 Checking Route Information and Alternatives
To get a map overview of the planned route and check different parameters of the planned route, perform
the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. In the Navigation menu, tap .
3. The planned route is displayed in its full length on the map with the following additional information:
The total length of route
The total time of route.
4. You have the following options on this screen:
Tap to receive detailed information about the route.
If you tap on the right side of the screen, you can narrow the route
information, for example to show only freeway sections or toll roads.
44
Tap to list route alternatives and select the most suitable route for you.
Tap on the Route Summary screen to carry out additional actions, for example edit
your route preferences or display the itinerary.
3.3 Checking Traffic Events
Offline statistical traffic information (historical speed information or traffic patterns) can be taken into
account in the route calculation based on the time of day and the day of week if suitable data can be
found on the device. In addition, real-time traffic information can help you avoid current traffic events like
temporary road closures or traffic jams caused by an accident. Both functions are subject to data
availability.
For information on traffic icons, see page 21.
Road segments affected by traffic events are displayed in a different color on the map, and small symbols
above the road show the nature of the event.
To check the traffic summary, perform the following steps:
1. On the Navigation view, tap the traffic icon in the corner (for example, ) to open the Traffic
Summary screen.
45
2. If there is at least one significant event on the planned route, a description is displayed about the
next event. Tap to see the list of all events.
3. Tap any of the list items to see its details and to display the affected road segment in its full length
on the map.
To display real-time traffic information on the map, perform the following steps:
1. On the Navigation view, tap the traffic icon (for example, ) to open the Traffic summary
screen and tap .
2. Tap to display real-time traffic information on the map. A 2D map is displayed with road
segments colored by the impact on the traffic flow.
46
Tap to display historical traffic information. A 2D map is displayed with road segments
colored by the likely density of the traffic in the given period. The information relevant for the
current period is shown when you open the screen. If necessary, you can browse the map for a
better view of certain road segments. Modify the day of week and the time of day to see the
desired period.
3.4 Editing the route
When navigation has already started, there are several ways to modify the planned route. You have the
following options:
Setting a new starting point, see page 47
Adding an additional destination, see page 48
Modifying the list of destinations, see page 49
Saving the planned route, see page 49
Deleting the planned route, see page 50
Selecting a route alternative when planning the route, see page 51
Selecting a route alternative for an existing route, see page 52
Pausing guidance, see page 1.
47
3.4.1 Setting a new starting point
For normal navigation, all routes are calculated from the current position. You can pause navigation to
check future routes, simulate them or see their length in time and distance. Then you can set the starting
point of the route to a location other than the current GPS position.
1. Press the navigation hardkey button to access the Navigation menu.
2. In the Navigation menu, tap .
3. The first line from the bottom is the start of the route, normally the current GPS position. Tap
, select , and confirm your action at the warning message.
4. The Change Start to... screen appears. Select the starting point of the route the same way you
select a destination.
5. The Multipoint Route screen appears where you can continue adding a destination to your route.
48
6. Tap to continue. The map returns with a transparent position marker (showing
that there is no GPS reception). If a planned route already exists, it is now recalculated starting
from the selected location.
7. To return to normal navigation, tap .
3.4.2 Adding an additional destination
If you already have a planned route and you select a new destination as described in the above sections,
the route to the previous destination is deleted and a new route is calculated.
To add a new intermediate destination to the planned route, perform one of the following actions:
Tap the map anywhere to browse it. After selecting the location on the map, tap
and to add the selected location to your route as an
intermediate destination. The other destinations of the route remain intact.
Press the navigation hardkey button and tap . Add a destination to your route as
described on page 42.
49
3.4.3 Modifying the list of destinations
To edit your route, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. In the Navigation menu, tap .
You have the following options on this screen:
Tap to delete all the destinations, or optimize the waypoints or the
route.
Tap the name of the intermediate destination to move it up or down in the list, to save the
location, or to delete it from the list.
If you have a route with at least one intermediate destination, you can delete the waypoint
from the list by tapping on it or by going to the Navigation menu. Tap in the
Navigation menu, then confirm the deletion.
3.4.4 Saving the planned route
To save the planned route, perform the following steps:
1. Select a destination as described earlier.
2. Tap and .
50
3. Type in a name and tap .
4. The route is saved and it is available in in the Navigation menu.
By selecting a previously saved route, Alpine Navigation System recalculates the route using the saved
destination and/or the waypoints.
3.4.5 Deleting the planned route
You have the following two options to delete the navigated route:
If you already have a planned route and you select a new destination as described in the above
sections, the route to the previous destination is automatically deleted and a new route is
calculated.
In the Navigation menu, tap or . If there are no waypoints, the planned route is
deleted after a confirmation. If you have waypoints, you can choose to delete the whole route, or
only the next waypoint.
51
3.4.6 Selecting a route alternative when planning the route
To select from different route alternatives or change the route planning method after you have selected a
new destination, perform the following steps:
1. Select a destination as explained earlier, and go to the route confirmation screen.
2. Tap .
3. You can see the basic details of route alternatives. Tap any of them to see it on the map.
4. To view more suggestions, tap and scroll down for other alternative routes
with different route planning methods.
5. Select one of the route alternatives and tap to return to the previous screen.
Alpine Navigation System recalculates the route. Tap to start your journey.
The orange line now shows the new planned route.
52
3.4.7 Selecting a route alternative for an existing route
To recalculate the planned route with a different route planning method and to compare different route
alternatives, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. You can access the list of route alternatives from the Navigation menu in one of the following
ways:
Tap and .
Tap and .
3. You can see the basic details of a few route alternatives. Tap any of them to see it on the map.
If there are suitable alternatives calculated with the route planning method that is selected in Route
preferences (page 70), they are shown on top of the list. Routes with other route planning methods
are shown at the bottom of the list.
4. If there are more than a few suggestions, you can tap and scroll down for
routes.
5. Select one of the route alternatives and tap to return to the previous screen.
Alpine Navigation System replaces the original route. Tap to start your
journey. The orange line now shows the new planned route.
53
3.5 Saving a location
To add any location to the saved locations (the list of frequently used destinations), perform the following
steps:
1. Select a destination as described before. It can be an address, a Place, any location on the map, a
previously used destination from History, and so on.
2. When the map appears with the route, tap .
3. Tap .
4. (optional) Using the keyboard, you can change the name offered for the Saved Location.
5. Tap to save the location.
To add your home and work address to the saved locations, perform the following steps:
1. Press the navigation hardkey button, and tap on the Navigation view .
2. Tap or . Tap to confirm your
selection.
3. You can search for the address as described on page 24.
Planning a route to one of the saved locations is described on page 38.
54
3.5.1 Editing a Saved Location
To edit a location that you have already added as a Saved Location, perform the following steps:
1. Press the navigation hardkey button, and tap .
2. The list of Saved Locations is displayed.
3. Tap and .
4. Tap the location you want to edit, tap and enter the name of the location on
the keyboard, then tap .
Note!
In Saved Locations, Home and Work cannot be renamed. To change your home or work
location, tap or , and confirm the address
change.
5. Tap .
Adding a location to the list of Saved Locations is described on page 53.
3.6 Adding an Alert Point
You can save any map location as an Alert Point, for example a speed camera or a school zone.
1. If you would like to save an Alert Point for the first time, switch on the . In the
Navigation menu, tap , , then . Switch on
and confirm your selection.
55
Note!
The warning for road safety cameras is disabled when you are in a country where road
safety camera warning is prohibited. However, you must make sure that using this feature is
legal in the country where you intend to use it.
1. Return to the Navigation view, and select the Alert Point. The red cursor ( ) appears there.
2. Tap .
3. Scroll down the list and tap .
4. Select the type of the Alert Point, the direction from which you expect the alert, and (if applicable)
the speed limit for this Alert Point.
5. Tap to save the location as a new Alert Point.
56
3.7 Running a Simulation
To run a simulated navigation that demonstrates the planned route, perform the following steps:
1. Press the navigation hardkey button to access the Navigation menu.
2. In the Navigation menu, tap .
3. Tap .
4. Tap . The simulation starts from the starting point of the route and leads you
through the whole planned route using a realistic speed.
(optional) You have the following controls during the simulation (the control buttons disappear after
a few seconds but you can open them again if you tap the map):
: Jump to the next route event (maneuver).
: Pause the simulation.
: Jump to the previous route event (maneuver).
57
: Tap to increase the speed of the simulation to 4, 8 or 16 times faster. Tap again to
return to normal speed.
5. Tap to stop the simulation.
3.8 Off-road navigation
When first started, Alpine Navigation System calculates routes using the road network of the maps
provided with the product. If you want to disregard roads during navigation, you can switch to off-road
mode, for example when driving in a desert.
3.8.1 Switching to off-road navigation
To switch to off-road navigation, perform the following steps:
1. Press the navigation hardkey button, and tap , and .
2. Tap and select .
Most of the procedures described for on-road navigation also apply to off-road navigation. However, there
are some that are not available in this navigation mode. For example:
You cannot open the itinerary as you have no maneuvers just route points and straight lines
between them.
There are no route alternatives and route planning method.
Vehicle settings are disabled.
3.8.2 Selecting the destination in off-road mode
Selecting a destination (waypoint or final destination) is the same as described in the previous sections.
The only difference is that route points are linked to form a route with straight lines regardless of the road
network and traffic regulations.
58
3.8.3 Navigating in off-road mode
The real difference between on-road and off-road modes is the navigation itself. When you are on the
Navigation view with an off-road route:
Your position and heading is not aligned to the nearest road.
There is no turn-by-turn navigation, just a recommended direction.
You can see an orange line drawn between your current position and the next destination to reach. The
Turn Preview field in the top left corner shows a compass with your bearing and the distance of the next
destination.
When you reach the final destination, the navigation ends.
Note!
If you do not want to use off-road navigation, switch back to on-road navigation by tapping
and .
3.9 Updating the navigation software and the maps
To update your navigation software and its maps, you need the following:
A PC equipped with the following:
Microsoft Windows® operating system (Windows XP Service Pack 2 or later)
Internet connection
USB port
An empty USB storage device with a capacity of at least 2 GB
To update your navigation software and its maps, perform the following steps:
1. Download and install the Toolbox PC tool on your PC.
a. Go to the alpine.naviextras.com website. If you do not have a user account yet, create one.
b. Click Download PC tool on the right side of the page to access the download page.
c. Follow the instructions on the site to download and install the Toolbox PC tool on your PC.
2. Collect navigation device information on a USB storage device.
59
Caution!
Do not switch off your navigation system during the following process.
Do not remove the USB storage device until the preparation process is completed.
a. Start the navigation system while your vehicle is parked.
b. Insert the empty USB storage device into the USB port of your navigation system.
c. Press the navigation hardkey button, and in the Navigation Menu, tap and
.
d. Tap Yes on the confirmation screen. The collection of device information starts, and a
progress bar shows the status of the process.
e. Wait until you receive the following message: Device information has been stored
successfully on the USB storage media. Remove the USB storage device from your
navigation system.
3. Download updates with the Toolbox PC tool.
a. Connect the same USB storage device to your PC.
b. Start the Toolbox PC tool on your PC and sign in with your Naviextras user name and
password.
c. Use the Toolbox PC tool to download updates and to purchase additional extras at your
convenience. For instructions on using the Toolbox, see the Toolbox How-to Guides at
alpine.naviextras.com/shop/portal/support.
d. Once the download is complete, remove the USB storage device from the PC.
4. Perform the update on your navigation system.
Caution!
Do not switch off your navigation system during the following process.
Do not remove the USB storage device until the preparation process is completed.
a. Start the navigation system while your vehicle is parked, and go to any navigation-related
screen.
b. Insert the USB storage device that now contains the updates into the USB port of your
navigation system.
c. Tap Yes on the confirmation screen. The software update starts, and a progress bar shows
the status of the process.
d. Wait until you receive the following message: The software update has been successfully
completed. Remove the USB storage device from your navigation system.
The navigation system will start using the updated maps next time you start the car.
Note!
If you switch off the navigation system or remove the USB storage device during the update
process, it will continue the update on next launch.
60
4 Reference guide
The following sections describe the different concepts and menu screens of Alpine Navigation System.
4.1 Concepts
The following sections describe and explain navigation-related concepts.
4.1.1 2D/3D GPS reception
The GPS receiver uses satellite signals to calculate its (your) position and needs at least four signals to
give a three-dimensional position, including elevation. Because the satellites are moving and because
objects can block the signals, your GPS device might not receive four signals. If three satellites are
available, the receiver can calculate the horizontal GPS position but the accuracy is lower and the GPS
device does not give you elevation data; only 2D reception is possible.
Several factors have an impact on the deviation between your real position and the one given by the GPS
device. For example, signal delay in the ionosphere or reflecting objects near the GPS device have a
different and varying impact on how accurately the GPS device can calculate your position.
4.1.2 Natural and TTS voices
Natural voices are the traditional type of voice instructions. Every phrase that occurs in voice guidance
messages is recorded in a studio with a real person. The advantage of pre-recorded voice is that it
sounds really natural, but the range of instructions that can be given this way is limited. Location-specific
information such as street names cannot be announced.
TTS technology provides a machine-generated way to give voice instructions. The advantage of TTS is
that it can announce street names, traffic events, route summary, and traffic rules.
4.1.3 Road safety cameras and other proximity Alert Points
There is a special proximity warning for road safety cameras (like speed or red light cameras) and other
proximity Alert Points (like schools or railroad crossings). These Alert Points are not part of Alpine
Navigation System. You can download Alert points from alpine.naviextras.com or you can upload points
in a specific text file if needed.
There is a proximity warning for special locations such as schools or railroad crossings. You can add your
own Alert Points. See page 54.
The application can warn you when you approach road safety cameras like speed cameras or dangerous
areas like school zones or railroad crossings. You can set up the different alert types individually in the
Warnings settings, see page 75.
The following warning types are available:
61
Audio warning: beeps are played (if the voice guidance language that you selected is a natural
voice) or the type of the alert can be announced (TTS voice) while you are approaching one of
these points, and an extra alert warns you if you exceed the given speed limit while approaching.
Visual warning: the type of the Alert Point, its distance and the related speed limit appear on the
Navigation view while you are approaching one of these locations.
For some of the Alert Points, either the enforced or expected speed limit is available. For these points, the
audio alert can be different if you are below or above the given speed limit.
Only when speeding: The audio alert is only played when you exceed the given speed limit.
When approaching: The audio alert is always played when approaching one of these Alert Points.
In order to draw your attention, the alert is different when you exceed the speed limit.
Note!
The warning for road safety cameras is usually disabled when you are in a country where road
safety camera warnings are prohibited. Make sure that using this feature is legal in the country
where you intend to operate. Use it on your own responsibility.
4.1.4 Route calculation and recalculation
A route is a sequence of route events, that is, maneuvers (for example, turns and traffic circles) to reach
the destination. The route contains one starting point and one or more destinations. The starting point is
the current (or last known) position by default. If you need to see a future route, the starting point can be
replaced with any other given point. See page 47.
Once the destination has been selected, Alpine Navigation System calculates the route based on your
preferences. These preferences are the route planning method, the vehicle type, and the road types used
or avoided when calculating the route. For detailed information on all the preferences, see Route
preferences settings, page 70.
Real-time traffic events are also taken into account, which sometimes greatly modify the route. See page
62.
Alpine Navigation System automatically recalculates the route if you deviate from the proposed itinerary.
If traffic services are enabled, Alpine Navigation System considers real-time dynamic traffic information in
route calculation and may also recalculate the route if the traffic situation changes during navigation.
Intelligent data (captured historical speed information based on probe data) is used for optimal routing
depending on the day of the week and time of day. Route segments where traffic flow is typically slow at
the given time of day and day of the week are avoided if a suitable alternative can be found. When
calculating the optimal route, the data relevant for the time of the estimated arrival of the vehicle at the
given route point is taken into account. As a result, Alpine Navigation System may suggest a different
route during the weekday rush hours, especially in major cities with frequent traffic jams. See page 62.
4.1.5 Smart Zoom
Smart Zoom provides the following features:
While following a route: When approaching a turn, it zooms in and raises the view angle to let
you easily recognize your next maneuver. If the next turn is at a distance, it zooms out and lowers
the view angle to be flat so you can see the road in front of you.
62
While driving without a planned route: Smart Zoom zooms in if you drive slowly and zooms out
when you drive at a high speed.
4.1.6 Speed limit warning
Maps may contain information about the speed limits of the road segments. Alpine Navigation System is
able to warn you if you exceed the current limit. This information may not be available for your region, or
may not be fully correct for all roads on the map.
The maximum speed set in the vehicle profile (page 70) is also used for this warning. Alpine Navigation
System alerts you if you exceed the pre-set value even if the legal speed limit is higher.
Speed warning can be fine-tuned in Warnings. See page 75.
You can also set the relative speed tolerance above which the application initiates the warning.
The following warning types are available:
Audio warning: You receive a verbal warning when you exceed the speed limit with the given
percentage.
Visual warning: The current speed limit is shown on the map when you exceed it (for example
).
You can also choose to see the speed limit sign on the map all the time.
4.1.7 Historical traffic
If statistical traffic information is stored with the map data, Alpine Navigation System can take them into
account when planning a route. In normal cases, these statistics help you avoid usual traffic jams on the
given day of week in the given hour but in some cases like on public vacations that fall on normal
weekdays, they can be misleading. You can enable or disable this feature in Traffic settings. See page
80.
4.1.8 Real-time traffic
Real-time traffic information can provide you with the current status of the traffic. Route calculation can
avoid road blocks or unexpected traffic jams caused by an accident.
The following data sources are available:
Traffic Message Channel (TMC):
63
TMC is a specific application of the FM Radio Data System (RDS) used for broadcasting real-time
traffic and weather information.
If public Traffic data is broadcast at your location, Alpine Navigation System automatically
searches the FM radio stations for TMC data, and the decoded information is immediately used in
route planning.
Note!
TMC is not a global service. It may not be available in your country or region. Ask your
local dealer for coverage details.
The application automatically takes account of the traffic events received. You do not need to set
anything in Alpine Navigation System.
When Alpine Navigation System receives traffic information that may affect your route, it warns you that it
is recalculating the route. The navigation continues with a new optimal route considering the most up-to-
date traffic conditions.
For information on traffic icons, see page 21.
To fine-tune this service, you have the following options in Traffic settings (page 80):
Set the minimum amount of time that you think is worth saving at the cost of a detour.
Instruct Alpine Navigation System to have you confirm the new planned route before it takes effect.
Note!
If there are traffic events on the planned route that the application has not bypassed, the
icon opens the list of significant traffic events to let you quickly check them.
4.1.9 Intelligent navigation
With the help of intelligent navigation, the planned route can adapt to traffic and other changes during
navigation. The following sections describe these features.
4.1.9.1 Congestion detour on highways
Alpine Navigation System may offer a detour when you slow down on a highway due to a traffic jam. The
Potential congestion detour window appears and shows the length and duration of the detour.
64
You can ignore this message and keep the original route by tapping or you can
check the suggested route by tapping .
By tapping the plus/minus signs, you can increase or decrease the distance to avoid on the highway.
You can accept the recommended detour by tapping .
4.1.9.2 Real-time alternative routes
Alpine Navigation System may offer an alternative route on normal roads in case of a traffic jam. The
possible alternative route window appears and shows the length and duration of the detour.
You can ignore this message and keep the original route by tapping or you can
check the suggested route by tapping . You can accept the recommended detour by
tapping .
65
4.1.9.3 Parking around destination
If you leave the planned route by exiting a freeway, Alpine Navigation System tries to guess the reason
for making a detour. By tapping , you can open a top-down map with the recommended parking
Places around the destination. By tapping the arrows on the sides, you can switch between the
recommended parking facilities.
By tapping and , the selected parking place becomes your
destination.
If the online parking service is enabled and it is available at your current position, you can receive real-
time data on the occupancy of some parking facilities. If the online parking service is not available, Alpine
Navigation System is searching for parking places in the Places of Interest.
4.1.9.4 Hints upon detour
If you leave the planned route by exiting a freeway, Alpine Navigation System tries to guess the reason
for making a detour. The Reason for detour window appears and shows available gas stations,
restaurants or other Places around the current position. Also, if there are avoidable parts of the original
route ahead (like a tunnel, a toll road or a ferry), you can find them in the list, in case you want to bypass
them.
By tapping one of the Places, Alpine Navigation System creates a waypoint and navigates you to the
selected place. You can ignore them by tapping .
66
4.2 Information menu
The Information menu provides various additional functions. It can be found in the Navigation menu. You
need an Internet connection via your cell phone to access online services, like parking and weather
information.
Button
Description
Shows information on the current position (latitude, longitude, nearest town, next crossing
street, and so on) or the last known position if GPS reception is not available. See page 67.
Offers assistance near your current position. See page 37.
Offers a list of countries with useful driving information about the selected country (for example
speed limits, maximum blood alcohol level).
Shows statistical data of your trips, like the start time, end time and average speed, see page
68. Track logs, the sequence of the positions given by the GPS receiver, can be saved together
with the trip logs. They can later be displayed on the map.
Shows a world map with the sunlit and dark areas of the world. Tap to
check the exact sunrise and sunset times for all your route points.
Shows the GPS Information screen with satellite position and signal strength information.
Shows the version of Alpine Navigation System, licenses, content, demo routes, credits,
statistics, and the SWID.
67
4.2.1 Where Am I
This screen contains information about the current position (or about the last known position if GPS
reception is not available). You can access it the following two ways:
By going to the Navigation menu and tapping and .
By tapping the current street name if it is displayed below the current position marker on the map.
The following information is shown on the Where Am I screen:
Address details (when available) of the current position
Latitude and Longitude (coordinate of the current position in WGS84 format)
The nearest town
Next crossing road/street
Previous crossing road/street.
You can also perform some actions on this screen.
Tap and to add the current position to the Saved Locations and
to check the country information.
You can also search for assistance near your current position. Tap to open a new screen for
quick search and select a category. For detailed information, see page 37.
68
4.2.2 Trip Monitor
Trip Monitor logs information about your route.
You can record a new trip by tapping and stop it by tapping .
By tapping on the Trip Monitor screen, you can select the following options:
Button
Function
By selecting a recorded trip, you can delete, rename, or change the color of the
recorded route.
You can access the Trip Monitor Settings, where you can enable saving the trip logs
automatically or you can save the trip logs manually. See page 81.
By tapping your recorded trip on the Trip Monitor screen, you can check information such as time, speed,
altitude and distance.
By tapping on the Trip Data Details screen, you can view the trip on the map, export
track logs, and check the elevation and speed profiles.
4.3 Setup menu
You can configure the navigation settings, and modify the behavior of Alpine Navigation System, by
pressing the navigation hardkey button, and tapping .
Tap the arrows to view the content of other pages.
69
The Setup menu provides the following options:
Button
Function
Select the type of vehicle you are driving, the road types used in route planning, and the route
planning method.
Adjust the different sound volumes.
Enable and set up warnings for speed limit, Alert Points (such as speed cameras), and road
signs.
Fine-tune the appearance of the Navigation view or adjust how the software helps you navigate
with different kinds of route-related information on the Navigation view.
Change the voice guidance language, set the time zone, the measurement units, the time and
date, and formats, and customize the application for your local language.
Enable or disable menu animations, set separate themes for daytime and nighttime use.
Enable or disable traffic information and modify detour settings.
Turn the automatic trip log saving on or off and check the current size of the trip database.
Enable or disable collecting usage information and GPS logs that may be used for improving
the application and the quality and coverage of maps.
Modify the basic software parameters set during the initial set-up process. See page 6.
Create or use your own user profile for navigating, to be able to use your own settings.
Delete all saved data and reset all settings to their factory defaults.
70
4.3.1 Route preferences
The following settings determine how routes are calculated:
Button
Function
Set the type of vehicle you want to use to navigate the route. Based on this setting,
some of the road types can be excluded from the route, or some of the restrictions
may not be taken into account in route calculation. See page 70.
Edit the parameters of the vehicle profile. See page 70.
Optimize the route calculation for different situations and vehicle types by changing
the planning method. See page 72.
Select on-road or off-road navigation. See page 57.
Select your preferred road types for the route. See page 72.
4.3.1.1 Vehicle profile
You can select the following vehicle types:
Button
Description
Maneuver restrictions and directional constraints are taken into account when
planning a route.
Roads are used only if access for cars is allowed.
Private roads and resident-only roads are used only if they are inevitable to reach
the destination.
Walkways are excluded from routes.
All maneuvers are available in intersections.
One-way streets are taken into account so that driving in the opposite direction is
allowed at low speed.
A private road is used only if the destination is there.
Walkways are excluded from routes.
Maneuver restrictions and one-way streets are taken into account when planning a
route.
Roads are used only if access for buses is allowed.
Private roads, resident-only roads and walkways are excluded from routes.
71
Maneuver restrictions and one-way streets are taken into account when planning a
route.
Roads are used only if access for taxis is allowed.
Private roads, resident-only roads and walkways are excluded from routes.
Maneuver restrictions and one-way streets are taken into account when planning a
route.
Roads are used only if access for trucks is allowed.
Private roads, resident-only roads and walkways are excluded from routes.
U-turns are excluded from routes (turning back on a divided road is not considered
as a U-turn).
If the map contains data on dimension, weight and freight restrictions, they can also
be taken into account when planning a route.
Creating a profile makes it possible to set up vehicle parameters used in route planning. You can have
several profiles for the same vehicle.
To add a new vehicle profile, perform the following steps:
1. Tap , browse the list of vehicles, and tap .
2. Select the vehicle type and set the parameters below. Depending on the vehicle type, some
parameters may not be available in the list.
You can set the following parameters:
Button
Function
Rename the profile for something meaningful, for example John's car.
Set the maximum speed you travel at.
Enter the average consumption of your vehicle in built-up areas. The unit for
consumption can be set in Regional settings.
Enter the average consumption of your vehicle on highways. The unit for
consumption can be set in Regional settings.
Select the engine and fuel type of your vehicle. It helps estimate the CO2 emission.
To reset all vehicle profiles to their default settings, tap , , and
.
72
4.3.1.2 Route Planning Method types
You can select from the following route planning method types:
Button
Description
Gives a quick route if you can travel at or near the speed limit on all roads. Usually,
the best selection for fast and normal cars.
Results in a route with fewer turns and no difficult maneuvers. With this option, you
can make Alpine Navigation System take, for example, the freeway instead of a
series of smaller roads or streets.
Gives a short route to minimize the travel distance. It can be optimal for slow
vehicles. Searching for a short route regardless of the speed, this route type is
rarely optimal for normal vehicles.
Gives a quick but fuel-efficient route based on the fuel consumption data. Travel
cost and CO2 emission calculations are estimations only. They cannot take
elevations, curves and traffic conditions into consideration.
Combines the benefits of Fast and Short. Alpine Navigation System calculates as if
it were calculating the Fast route, but it takes other roads as well to save fuel.
Depending on the vehicle type, some methods may not be available.
4.3.1.3 Navigation Mode
You can switch between on-road and off-road navigation by tapping and selecting
or (page 57).
4.3.1.4 Road types
To let the route fit your needs, you can also set which road types are to be considered for or to be
excluded from the route.
Excluding a road type is a preference. It does not necessarily mean total prohibition. If your destination
can only be accessed using some of the excluded road types, they are used only as much as necessary.
In this case, a warning icon is shown on the Route information screen, and the part of the route not
matching your preference is displayed in a different color on the map.
Some road types are only available in certain regions.
The following road types are available:
Button
Description
You might need to avoid freeways when you are driving a slow car or you are
towing another vehicle.
73
Charge roads are pay roads where you can purchase a pass or vignette to use the
road for a longer period of time. They can be enabled or disabled separately from
toll roads.
Per-use toll roads are pay roads where there is a per-use charge in the routes by
default. If you disable toll roads, Alpine Navigation System plans the best toll-free
route.
Alpine Navigation System includes ferries in a planned route by default. However, a
map does not necessarily contain information about the accessibility of temporary
ferries. You might also need to pay a fare on ferries.
Car shuttle trains are used to transports vehicles for a relatively short distance and
they usually connect places that are not easily accessible on a road, for example, in
Switzerland.
Carpool or HOV lanes can be used if a given number of passengers is traveling in
the vehicle. Check whether you are allowed to use carpool lanes before enabling
this road type.
Alpine Navigation System excludes unpaved roads by default. Unpaved roads can
be in a bad condition and you usually cannot reach the speed limit on them.
4WD tracks are dirt roads of very poor condition. They can only be driven by 4WD
vehicles. Alpine Navigation System excludes 4WD tracks by default.
4.3.2 Sound
You can modify the following settings:
Button
Function
This is the main volume control. Adjust all the sound types below or mute them.
Adjust the volume of the guidance sounds (verbal instructions) or mute it.
Adjust the volume of the non-verbal alert sounds (beeps) or mute it.
Turn off the attention tone preceding verbal instructions or adjust its volume.
Adjust the volume or mute the sound played when pressing the button.
74
You have the following options for each sound type:
Button
Function
Volume slider
Adjust the volume of the related sound.
Mute the related sound. The slider becomes inactive. Tap again to re-enable it.
Button
Function
Disable verbal instructions. This function is enabled by default.
Choose from the following options:
Announce the street names in the native language area of the selected voice
guidance language.
Announce the road numbers only.
Announce the maneuvers only.
Street names sound correct only if you use a native voice profile for the country.
Choose from the following options:
Try to read the street names in a foreign country.
Announce the road numbers only.
Announce the maneuver only.
Set whether you want an immediate announcement for the next maneuver after
each turn, or it is enough to receive the information when the turn is near.
Set the verbosity of the voice instructions, that is how much they tell and how often
they speak.
Minimal: the voice instruction is given once right before the next maneuver.
Medium: the voice instruction is given when approaching the next maneuver
and it is repeated right before the maneuver.
Verbose: the voice instruction is given first relatively far from the next
maneuver, it is repeated when approaching the next turn, and it is repeated
again right before the actual maneuver.
Allow reading out a quick summary of the route whenever a route is calculated.
Allow reading out information about the country you have entered, when you cross
country borders.
Allow reading out real-time traffic messages.
75
Allow announcing system messages.
4.3.3 Warnings
You can enable and modify the following settings:
Button
Description
Alpine Navigation System is able to warn you if you exceed the current speed limit.
This information may not be available in your region, or may not be fully correct for
all roads on the map.
The maximum speed set in the vehicle profile is also used for this warning. Alpine
Navigation System alerts you if you exceed the pre-set value even if the legal speed
limit is higher.
This setting lets you decide whether you wish to receive visible and/or audible
warnings.
The following warning types are available:
Visual warning: the current speed limit is shown on the map when you
exceed it.
Audio and Visual warning: besides the current speed limit being shown on
the map, you also receive a verbal warning when you exceed the speed limit
with the set percentage.
If you prefer to see the speed limit sign on the map all the time (normally, it is shown
only if you exceed the limit), you can set it here.
You can also set the relative speed above which the application initiates the
warning by adjusting a slider. The value can be different within and outside towns.
76
Tap it to receive a warning when approaching a road safety camera or other Alert
Points like school zones or railroad crossings. You must make sure that using this
feature is legal in the country where you intend to use it.
You can set the warning type for the different Alert Point categories (alert types)
individually. The following warning types are available:
Visual warning: the type of the Alert Point, its distance, and the related speed
limit appear on the Navigation view while you are approaching one of these
locations.
Audio and Visual warning: besides the visual alert, beeps are played (when
using a natural voice) or the type of the alert is announced (in case of a TTS
voice) while you are approaching one of these points, and an extra alert
warns you if you exceed the given speed limit while approaching.
For some of the Alert Points, the enforced or expected speed limit is available. For
these points, the audio alert can be different if you are below or above the given
speed limit.
Only when speeding: The audio warning is only played when you exceed the
given speed limit.
When approaching: The audio warning is always played when approaching
one of these Alert Points. In order to draw your attention, the audio alert is
different when you exceed the speed limit.
Maps may contain driver alert information that can be shown on the Navigation view
in a similar way as real-life road signs. Tap it to enable or disable the warning for
these road segments (for example, dangers and sharp curves). For each category
of warning signs, set the warning type (visual or audio and visual) and the distance
from the hazard to receive the warning at.
4.3.4 Navigation View
These settings allow you to fine-tune the appearance of the Navigation view. You can also adjust how the
software helps you navigate with different kinds of route-related information on the Navigation view.
Tap to adjust the navigation view to your needs, choose suitable color themes from
the list for both daytime and nighttime use, show or hide 3D buildings, landmarks, and manage your
Place visibility sets (which Places to show on the map).
77
You can modify the following settings:
Button
Function
Adjust the basic zoom and tilt levels to your needs. Three levels are available.
Switch between daytime and night color modes or let the software switch between
the two modes automatically a few minutes before sunrise and a few minutes after
sunset.
Select the color scheme used in daytime mode. Daytime colors are bright and
similar to paper road maps.
Select the color scheme used in night mode. Night colors are darker to keep the
average brightness of the screen low.
Show or hide 3D landmarks (3D representations of prominent or well-known
objects).
Show or hide 3D city models (3D block representation of full city building data
containing actual building size and position on the map).
Show or hide the 3D elevation of the terrain.
Turn on Track Logs to show them on the map or turn them off.
Select which Places to show on the map while navigating. Too many Places make
the map crowded so it is a good idea to keep as few of them on the map as
possible. Tap the name of the Place category to show/hide it or to open the list of its
subcategories.
You can modify the following additional settings on the Navigation View screen:
If you are navigating with a planned route, you can set three data fields to be
displayed on the Navigation view. You can choose from the time of arrival at
destination, distance to destination, time to destination, time of arrival at waypoint,
distance to waypoint, time to waypoint, heading, or altitude. Without a planned
route, there is only one data field that can be set to show the heading or the
altitude.
Turn the Route Progress Bar on or off. If turned on, an orange line is displayed on
the side of the screen, and a blue arrow on it shows your progress.
Turn it on to get freeway service information (for example gas stations, restaurants)
or turn it off if you do not need it.
Select the service types displayed for the freeway exits. Choose from the Places
categories.
78
Zoom out and show an overview of the surrounding area if the next maneuver is far
and you are driving on a freeway. When you get close to the event, the normal map
view returns.
Whenever adequate information is available, lane information similar to the real
ones on road signs above the road is displayed at the top of the map. Tap it to turn
this feature on or off.
If you are approaching a freeway exit or a complex intersection and the needed
information exists, the map is replaced with a 3D view of the junction. Tap it to turn
this feature on or let the map be displayed for the whole route.
When entering tunnels, the surface roads and buildings can be disturbing. Tap it to
show a generic picture of a tunnel instead of the map. A top-down overview of the
tunnel and the remaining distance are also displayed.
In certain situations, Alpine Navigation System offers a detour when there is a traffic
jam on a highway. See page 63.
In certain situations, Alpine Navigation System offers an alternative route when
there is a traffic jam on the road. See page 64.
In certain situations, Alpine Navigation System offers parking Places when you
approach your destination. See page 65.
In certain situations, Alpine Navigation System offers different route alternatives
when you leave the planned route and suddenly exit the freeway. See page 65.
4.3.5 Regional
You can modify the following settings:
Button
Description
It displays the current written language of the user interface. Tap it to select a new
language from the list of available languages. The application restarts after you
change this setting and confirm it.
79
It shows the current voice guidance profile. Tap it to select a new profile from the list
of available languages and speakers. Tap any of these to hear a sample voice
prompt. Just tap when you have selected the new spoken language.
Different voice profiles are capable of different levels of service:
Natural Voice (street names not announced): These pre-recorded sounds
can only tell you basic information about turns and distances.
TTS Voice (street names announced): These computed voices can read out
complex instructions, street names or system messages.
TTS Voice with a microphone icon: Besides the above-mentioned profiles, it
can also be used for voice recognition.
You can set the measurement units and time/date format to be used. Alpine
Navigation System may not support all the listed units in some voice guidance
languages.
By default, the time zone is taken from the map information and adjusted by your
current location. Here you can manually set the time zone and the daylight saving
time.
4.3.6 Display
You can modify the following settings:
Button
Function
When animation is turned on, buttons on menus and keyboard screens, and screen
transitions are animated.
Select the style and colors of the application used in daytime mode.
Select the style and colors of the application used in night mode. It is recommended
to use darker colors at night to avoid distraction during driving in the dark.
80
4.3.7 Traffic
You can modify the following settings:
Button
Function
Enable or disable the Traffic reception that can receive real-time traffic information.
The rest of the buttons below are all related to the Traffic function and are available
only if the receiver is enabled.
Tap it if you want to use online traffic information to avoid road blocks or
unexpected traffic jams.
If you want to see traffic events (for example closures, accidents, lane restrictions)
on the map, you can choose to show the events with a different color or to display
an icon too. This feature can also be disabled.
Receive information about normal traffic as well, not just special conditions or
events.
Enable or disable historical traffic data and traffic patterns. This locally stored
information can be very useful in normal circumstances but for example on public
vacations it may be better to turn it off in order not to take account of normal
weekday traffic jams.
Set the minimum amount of time that you think is worth saving at the cost of making
a detour.
For example, in the figure below, the orange route shows a traffic event that causes
a 30-minute delay. The blue route is a detour that is 15 minutes longer than the
original route (not counting the traffic jam). If you set the Offer detour feature to 10
minutes, Alpine Navigation System recalculates the route because it saves 15
minutes, which is more than the 10 minutes you set. If you set it to 20 minutes, the
original route is kept because the detour would save you only 15 minutes.
Calculations are based on information received about traffic events.
Enable or disable the manual confirmation of every recalculation due to traffic
events.
81
4.3.8 Trip Monitor
Trip logs contain useful information about your recorded trips. You can enable and modify the following
settings:
Button
Description
Trip monitor can record statistical data of your trips. If you need these logs later, you
can let the application save them automatically for you.
Track logs, the sequence of the positions given by the GPS receiver, can be saved
together with trip logs. They can later be displayed on the map. You can let the
application save track logs whenever it saves a trip.
This is not a button. This line shows the current size of the trip database, the sum of
all trip and track logs saved.
4.3.9 User Profiles
If more drivers use Alpine Navigation Systemfor navigating, their settings can be remembered by using
one of the user profiles.
You can create a new profile by tapping enter a name, and select a car model. If you
select a new profile, the application restarts so that the new settings can take effect.
By tapping , , you can select your profile and change the car
model and name of the profile, or delete the profile.
82
5 End-user license agreement
0. Definitions
The following terms shall have the meaning defined hereunder in this agreement when used with capital
letters. The text of this agreement may also contain further defined terms.
“Agreement” means this End User Licence Agreement (EULA) containing the terms and conditions of use
of the Software, Databases and Services by You as the end user.
“Database” or “Database Content” means geographically referenced data such as map data, points of
interest (“POI”), 3D models, TMC location tables, phonemes, images, audio or video files and other data,
as well as any data suitable for integration into the Software.
“Device” means the hardware equipment manufactured or distributed by Licensor on which the
Navigation Product is installed.
“Software” means the turn-by-turn navigation software installed on the Device, including the core engine,
other software modules and the graphical user interface, capable of processing and/or displaying the
Databases and the Services. The term Software shall by definition include any modifications, updates,
upgrades thereto.
“Service” means the provision of dynamically changing information that may be provided by-, displayed
by- or transmitted through the Software, for example, but not limited to Traffic Message Channel (TMC)
service, search, weather information and community based services. Services are usually transmitted
online via the Internet, but may be conveyed via other means (e.g. via radiowaves in case of “RDS TMC”
service).
“Navigation Product” means the Software, the Databases and the Services together, as (i) distributed with
the Device by the Licensor or (ii) otherwise installed on the Device.
1. The contracting parties
1.1 This Agreement has been entered into by and between You as the end user (hereinafter: “User”) and
the business entity distributing/selling the Device together with the Navigation Product, under its own
name and/or branding (hereinafter: “Licensor”). This Agreement sets out the conditions and limitations of
use of the Navigation Product. The User and the Licensor are referred together as: “Parties”.
1.2 User represents and warrants that (i) he/she is not located in a country that is subject to a U.S.
Government embargo, or that has been designated by the U.S. Government as a “terrorist supporting”
country; and (ii) he/she is not listed on any U.S. Government list of prohibited or restricted parties.
2. Conclusion of the Agreement
2.1 This Agreement is concluded by implicit conduct of the Parties without signing the Agreement.
2.2 The User hereby acknowledges that following the lawful acquisition of the Navigation Product
constituting the object of this Agreement, any of the following actions of use shall mean that the User has
accepted the terms and conditions of this Agreement as legally binding: (i) any degree of use, installation
onto a computer or other Device (mobile phone, multi-function device, personal navigation device, in-car
navigation or multi function head unit, etc.), (ii) pressing the “Accept” button displayed by the Navigation
Product during installation or use. The time of conclusion of the present Agreement is the time of
executing the first action of use (commencement of use).
2.3 This Agreement shall by no means authorize the usage of the Navigation Product by those persons
having unlawfully acquired the Navigation Product or having unlawfully installed it on a Device or in a
vehicle.
2.4 U.S. Government Users. If you acquire the Navigation Product by or on behalf of the United States
Government or any other entity seeking or applying rights similar to those customarily claimed by the
United States Government, you are on notice that the Navigation Product is a commercial item as that
83
term is defined at 48 C.F.R (“FAR”) 2.101 and that all use of the Navigation Product is subject to this
Agreement.
3 Applicable law and venue
3.1 This Agreement will be governed by the laws of the country where the Licensor has its statutory seat
or in the absence of such incorporation where it has its central administration (“country of residence”)
without regard to such country’s choice of law provisions.
3.2 The courts of the country of residence specified in Section 3.1. above shall have jurisdiction over all
disputes related to this Agreement.
3.3 If the User is a “consumer” (a natural person who purchased and uses the Navigation Product for
purposes outside its business activities or which can be regarded as being outside his trade or
profession), the above choice of law and choice of venue shall not, have the result of depriving the
consumer of the protection afforded to him by provisions (including any provision regulating the court
having jurisdiction) that cannot be derogated from by agreement by virtue of the law which, in the
absence of choice, would have been applicable.
3.4 The United Nations Convention on Contracts for the International Sales of Goods is hereby excluded
from application to this Agreement.
4. Object of the Agreement and Termination
4.1 The object of this Agreement shall be the Navigation Product as a whole and the components (the
Software, the Databases and the Services) thereof. User acknowledges that all author’s rights (including
the economic rights) vested in the Software are owned by NNG Software Developing and Commercial
Ltd. (registered seat: 35-37 Szépvölgyi út, H-1037 Budapest, Hungary; company reg.no.: 01-09-891838,
http://www.nng.com), herein referred to as: Software Owner.
4.2 Any form of display, storage, coding, including printed, electronic or graphic display, storage, source
or object code, or any other as yet undefined form of display, storage, or coding, or any medium thereof
shall be deemed parts of the Navigation Product.
4.3 Error corrections, updates or upgrades or any other modifications to the Navigation Product used by
the User following the conclusion of this Agreement shall also be used in accordance with this
Agreement.
4.4 Your rights under this Agreement will terminate immediately without notice from Licensor if you
materially breach them, or take any action in derogation of the rights of Licensor, any suppliers holding
rights in the Navigation Product and/or their suppliers. Licensor may terminate this Agreement if the
Navigation Product as a whole or any part thereof becomes, or in Licensor’s (or other suppliers holding
rights in the Navigation Product) reasonable opinion likely to become, the subject of a claim of intellectual
property infringement or trade secret misappropriation. Upon termination, you will cease use of, and
delete the Navigation Product and confirm compliance in writing to Licensor, if requested.
4.5 Licensor reserves the right to upgrade, modify, withdraw, suspend, or discontinue any Service
offering, functionality or feature of the Navigation Product or may terminate distribution of the Navigation
Product in its sole discretion due to reasons such as (but not limited to): the provision is no longer
financially or otherwise feasible for Licensor, technology advances, or conditions rules change, end user
feedback indicates a change or is needed, agreements with third parties no longer permit us to make their
Databases or Services available, or external issues arise that make it imprudent or impractical to continue
with the provision.
4.6 Licensor reserves the right to replace any Database or Service with another Database or Service
having the same or similar functionality. Such change may be executed upon the sole discretion of
Licensor.
5. Rights under copyright or other intellectual property rights
5.1 All material copyrights and other intellectual property rights vested in the Navigation Product or any
parts thereof, that are not explicitly granted in this Agreement or by virtue of law, are reserved.
84
5.2 Intellectual property rights of Licensor, the Software Owner or other rightholders extend to the whole
Navigation Product and to its parts separately as well.
5.3 The owner(s) of the copyrights of the Database(s) is (are) the Licensor, or natural person(s) or
corporate business entity(ies) (referred to as: “Database Owner”) who supply them. In the event that the
copyright owner of the Database is not the Licensor, the Licensor hereby states that it has obtained
sufficient usage and representation rights from the Database Owners in order to utilize the Databases in
line with this Agreement.
5.4 Services available through the Software may transmit various types of information or content to the
User, which information or content is gathered and provided by third party service providers. Therefore it
is understood and accepted that neither the Licensor nor the Software Owner has the ability or right to
control, alter or modify such information and content and the Service itself is only a function enabling the
Software to access, download and display information and content to the User.
5.5 Database Owners, service providers and any special terms and conditions regarding their products
contained in- or displayed through the Navigation Product may be listed in the “About” or similar menu
item of the Navigation Product, or in in the Device documentation or at a website address indicated in the
“About” section.
6. Rights of the User
6.1 Without prejudice to Section 6.2 below, by default the User is entitled to run the Navigation Product on
the Device the Navigaiton Product came preinstalled before purchase or on the Device in connection
which the Navigation Product was provided by Licensor, and to run and use one copy of the Navigation
Product or a preinstalled copy of the Navigation Product thereon. The Navigation Product is for the User’s
personal purposes only.
6.2 In the event that the Navigation Product comes preinstalled on- or otherwise licensed together with
the Device or acquired from Licensor by the User for a specific Device, the Navigation Product shall be
tied to the Device and may not be separated-, transferred to-, or used with another Device or sold to
another User without selling the Device itself.
6.3 The Databases and Services provided to the User may only be used together with User’s copy of the
Software and may not be used separately or with another copy of the Software.
7. Limitations of use
7.1 The User is not entitled
7.1.1 to duplicate the Navigation Product (to make a copy thereof) or any part of it, except to the extent
allowed by this Agreement or applicable law;
7.1.2 to resell, sublicense, lease, rent or lend it, or to transfer it to a third person for any reason without
transferring the Device on which it was first legally installed on (see section 6.2);
7.1.3 to translate the Navigation Product (including translation (compilation) to other programming
languages);
7.1.4 to decompile, disassemble, or reverse engineer the Navigation Product;
7.1.5 to evade the protection of the Navigation Product or to modify, circumvent or obviate such
protection through technological or by any other means;
7.1.6 to modify, extend, transform the Navigation Product (in whole or in part), to separate it into parts,
combine it with other products, install it in other products, utilize it in other products, not even for the
purpose of achieving interoperability with other devices;
7.1.7 to remove, modify or obscure any copyright, trademark notice, or restrictive legend included in the
Navigation Product or any part thereof.
7.2 The User may only use the Databases and information from the Services available through the
Navigation Product (including but not limited to the traffic data received from the RDS TMC or on-line
TMC traffic information service) for his/her own benefit and at his/her own risk. It is strictly prohibited to
85
store, to transfer or to distribute these data or contents or to disclose them in full or in part to the public in
any format or to download them from the Navigation Product.
8. No warranty, limitation of liability
8.1 The Licensor hereby informs the User that although the greatest care was taken in producing the
Navigation Product, given the nature of the Navigation Product and its technical limitations, the Licensor
and its suppliers do not provide a warranty for the Navigation Product being completely error-free, and
they are not bound by any obligation whereby the Navigation Product obtained by the User should be
completely error-free.
8.2 THE LICENSED NAVIGATION PRODUCT, INCLUDING ANY OF THE DATABASES, OR SERVICES
FORMING PART THEREOF ARE PROVIDED ON AN “AS IS” AND “WITH ALL FAULTS BASIS”
(INCLUDING NO WARRANTY FOR THE CORRECTION OF FAULTS) AND LICENSOR, THE
DATABASE OWNERS, THE SOFTWARE OWNER, THE SERVICE PROVIDERS AND THIRD PARTY
SUPPLIERS EXPRESSLY DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY,
SATISFACTORY QUALITY, ACCURACY, TITLE AND FITNESS FOR A PARTICULAR PURPOSE. NO
ORAL OR WRITTEN ADVICE OR INFORMATION PROVIDED BY LICENSOR OR ANY OF ITS
AGENTS, SUPPLIERS, EMPLOYEES, THIRD PARTY PROVIDERS, THE SOFTWARE OWNER OR
THE DATABASE OWNERS AND SERVICE PROVIDERS SHALL CREATE A WARRANTY, AND USER
IS NOT ENTITLED TO RELY ON ANY SUCH ADVICE OR INFORMATION. THIS DISCLAIMER OF
WARRANTIES IS AN ESSENTIAL CONDITION OF THE AGREEMENT.
Licensor does not warrant that the Navigation Product is capable of interoperating with any system,
device or product.
8.3 The Licensor does not assume any responsibility for damages incurred due to an error in the
Navigation Product.
8.4 The Licensor does not assume any responsibility for damages incurred due to the Navigation Product
not being applicable for any defined purpose, or due to the error or incompatibility of the Navigation
Product with any other system, device or product.
8.5 NEITHER LICENSOR NOR ITS SUPPLIERS SHALL BE LIABLE TO USER FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL, INDIRECT OR EXEMPLARY DAMAGES ARISING OUT OF THIS
AGREEMENT, INCLUDING LOST PROFITS OR COSTS OF COVER, LOSS OF USE OR BUSINESS
INTERRUPTION OR THE LIKE, REGARDLESS OF WHETHER THE PARTY WAS ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
NOTWITHSTANDING ANYTHING TO THE CONTRARY CONTAINED HEREIN, THIRD PARTY
SUPPLIERS (E.G. DATABASE OWNERS, MAP PROVIDERS, SERVICE PROVIDERS, THE
SOFTWARE OWNER) OR AGENTS OF LICENSOR SHALL HAVE NO MONETARY LIABILITY TO THE
USER FOR ANY CAUSE (REGARDLESS OF THE FORM OF ACTION) UNDER OR RELATING TO
THIS AGREEMENT.
IF YOU HAVE ANY BASIS FOR RECOVERING DAMAGES FROM LICENSOR OR ANY OF ITS
SUPPLIERS, YOU CAN RECOVER ONLY DIRECT DAMAGES UP TO THE AMOUNT THAT YOU PAID
FOR THE NAVIGATION PRODUCT (OR UP TO 10 USD IF THE AMOUNT IS NOT CALCULABLE OR IF
YOU ACQUIRED THE NAVIGATION PRODUCT FOR NO CHARGE). THE DAMAGE EXCLUSIONS
AND LIMITATIONS IN THIS AGREEMENT APPLY EVEN IF REPAIR, REPLACEMENT OR A REFUND
FOR THE NAVIGATION PRODUCT DOES NOT FULLY COMPENSATE YOU FOR ANY LOSSES OR IF
THE LICENSOR OR ITS SUPPLIERS KNEW OR SHOULD HAVE KNOWN ABOUT THE POSSIBILITY
OF THE DAMAGES.
8.6 The Licensor also draws the attention of the User to the fact that, when using the Navigation Product
in any form of vehicle, observing the traffic regulations and rules (e.g. use of obligatory and/or reasonable
and suitable security measures, proper and generally expected care and attention in the given situation,
and special care and attention required due to the use of the Navigation Product) is the exclusive
responsibility of the User. The Licensor shall not assume any responsibility for any damages occurred in
relation to use of the Navigation Product in any vehicle.
86
Safety (e.g. speed) cameras are provided for informational purposes only and may not be used to
encourage, facilitate or support the violation of any laws. Furthermore some countries prohibit the display
or use of such features. Compliance with country specific laws and any usage or reliance on the
information by user shall be at the User's own risk and sole responsibility.
8.7 Database and Services provided by third parties. The Licensor hereby excludes any liability of its own
for the Database or information obtained through the Services in the Navigation Product. The Licensor
does not warrant the quality, suitability, accuracy, fitness for a specific purpose or territorial coverage or
availability of the Database or information. The Licensor specifically excludes any and all liability for the
suspension or cancellation of any of the Services, and any damage arising due to cancellation of a
Service. User acknowledges that the mapping data in Databases may contain geographical data and
other data.
8.8 The User hereby acknowledges that (i) inaccurate or incomplete information due to the passage of
time, changing circumstances, sources used and the nature of collecting comprehensive geographic data,
may each lead to incorrect results; and (ii) that the Database or information obtained through the Services
provided by third parties may only be used at the risk of the User and for the benefit of the User. User
acknowledges that the Databases are the confidential information of Database Owners and disclosure of
the Databases to third parties is prohibited.
8.9 USE OF THE NAVIGATION PRODUCT’S REAL TIME ROUTE GUIDANCE FUNCTION IS AT
USER’S SOLE RISK AS LOCATION DATA MAY NOT BE ACCURATE.
8.10 Database Content and Services provided by the Licensor or an agent of the Licensor. For certain
Navigation Products the Licensor or the Software Owner or a contractual partner may offer various
products and services to the User through the http://www.naviextras.com or another dedicated website.
The User may only use these services when the User has read and understood the relevant terms at the
website and the User is obliged to use the services in line with those terms. In the event of conflict
between this Agreement and such additional terms, the additional terms shall prevail.
8.11 Purchase and acquisition of activation licence for the use of certain functions, Databases, or
Services may require Internet connection and no alternative way of acquisition is offered by Licensor or
the supplier of those functions, Databases, or Services.
9. Sanctions
9.1 The Licensor hereby informs the User that the breach of copyrights and related rights is a crime under
numerous jurisdicitons, including in the United States of America and other countries who ratified the
International Convention on Cybercrime.
9.2 Licensor, Software Owner and suppliers of products on the basis of this Agreement are continously
monitoring violation of their intellectual property rights, and in case infringing use is detected, violators will
face criminal and civil procedures initiated against them in any and all jurisdictions.
10. Anonymous data collection
10.1 The User hereby acknowledges that the Software may collect, transmit to Licensor or third parties,
and in some cases stores data connected to the usage of the Software by the User (e.g. movement/route
data, user interaction data). Such data collection functions may be disabled or enabled by User any time
from within the corresponding menu within the Navigation Product. The collected data is always
anonymous, not associated in any way with any personal information of the User or with the User itself.
10.2 The collected data may be uploaded to the Software Owner’s database or transmitted periodically or
in real time to a third party partner and used exclusively for the purpose of enhancing and improving the
precision and reliability of features and services of the Navigation Product. Uploading is executed through
the Sofware Owner’s special software or by the Device, and the upload may be enabled or disabled by
User. After successful data upload, the collected data is deleted from the Navigation Product and the
Device or may be deleted by the User manually.
10.3 Collected data is transmitted, stored and handled anonymously and no connection of the data with
the User shall be established by Licensor or any third party.
87
10.4 Licensor hereby informs the User, that if it accesses the Internet through mobile data service while
abroad or otherwise roaming another mobile network the transmission of such data may result in special
roaming charges. To avoid such charges it is the responsibility of the User to disable mobile data services
while roaming or to turn off the data collection functions of the Navigation Product.
11. Auxiliary Terms for Services
11.1 For online Services the following auxiliary terms shall also apply. Information or Database content
(e.g. weather-, traffic information, location based information, online search results) may be transmitted to
the User’s Device through an Internet connection (“Connected Services”). Connected Services may be
granted for a fee or free of charge subject to Licensor’s decision.
11.2 Information and content through Connected Services in general are not available in all countries, or
all languages, furthermore different conditions and service characteristics may apply in different countries.
Use of certain Connected Services may be prohibited in certain countries. It is the User's responsibility to
comply with country specific regulation. Licensor excludes its liability for the consequences of illegal use
of such functions and User shall indemnify and hold Licensor harmless from all claims against Licensor
from authorities or third parties due to the illegal use.
11.3 Online information and content are downloaded by the Navigation Product from the Software
Owner’s or other suppliers’ online content servers. The Licensor hereby excludes any liability of its own
for all information and content. As no control may be exercised by the Licensor or the Software Owner
over the information or content, neither Licensor nor Software Owner warrants the legality, quality,
suitability, accuracy, fitness for a specific purpose or territorial coverage of the information and content,
furthermore no warranty is offered regarding the availability (e.g. uptime) of online information and
content servers. User acknowledges that in any territory or time, slow- or non-connectivity may be
experienced due to capacity limitations of the Internet connection or the content servers. The Navigation
Product may allow the User to access and communicate third party servers directly. In such cases use of
such servers is for User's own risk entirely. Licensor shall not undertake any liability whatsoever for such
servers and services accessed and received directly form third parties.
Server availability. No warranty is provided regarding the availability of the servers enabling the Services.
When conducting periodic maintenance and inspection of the servers providing the Service (the
“System”) upon which Services operate, Licensor (or its Supplier) may temporary suspend all or part of
the Services. In the case of any of the following items, Licensor (or its Supplier) may temporarily interrupt
all or part of the Service without prior notification to the User:
(i) When conducting emergency maintenance or inspection of the System;
(ii) When it becomes no longer possible to provide operate the System due to an accident such as fire or
power outages, natural disasters such as an earthquakes or flooding, war, rioting, industrial disputes, etc.;
(iii) When Licensor deems it necessary to temporarily suspend operation due to unavoidable operational
or technical circumstances; or
(iv) When it becomes no longer possible to provide the Service due dto a System failure, etc.
11.4 User acknowledges that the data or information provided through Connected Services is not updated
in real-time and may not accurately reflect the real life situation or events.
11.5 The User hereby acknowledges that the Connected Services may only be used at the risk of the
User and for the benefit of the User. It is the sole responsibility of the User to provide and maintain a
connection to the public Internet network. User accepts that the usage of the Connected Services
generates data traffic (up- and downstream) and may result in increased mobile data service fees
payable by User.
11.6 Connected Services may provide data, information or materials supplied and/or licensed by third
parties to Licensor. For such materials different terms and conditions imposed by such third parties may
apply. Applicable third party terms shall be listed in the “About” section of the Navigation Product, in the
Device documentation, at a website address indicated in the “About” section or as part of this Agreement.
When first using / enabling Connected Services, User accepts compliance with those third party terms
and conditions.
88
11.7. Community Services. Some Connected Services may be based on data and information uploaded
by participating individuals (Users or other persons) or a Database created and maintained by a group of
such individuals. Such data may not come from a trusted source and may also be intentionally false or
misleading, as Licensor or Software Owner does not have any means to control or verify the credibility or
accuracy of such data or the individuals providing the data. Therefore User accepts that community type
Connected Services must be used with extreme care.
By participating in the community by providing data or any information via the Navigation Product or other
means offered by Licensor (e.g. through a website or other software), User shall accept the following:
(a) Licensor is granted a royalty-free right to use the data uploaded, in particular, to modify, display, make
available to the public, distribute, copy the data for any purpose;
(b) User warrants that no third party has any rights that would hinder or render impossible the use of the
data as set out in (a) above, and that no third party rights are infringed by uploading the data on those
conditions;
(c) User indemnifies and holds harmless Licensor from any claim from a third party against Licensor due
to violation of its rights regarding the uploaded data.
12. Third party supplier terms
12.1 Third parties supply Services or Database built into the Navigation Product and such third party
suppliers may have special terms and conditions of use (“Supplier Terms”), and You as the User accept
those terms together with this Agreement.
12.2 Potential third party suppliers (and their Supplier Terms) may have their Database or Service
distributed as part of the Navigation Product are listed in the “About” section of the Navigation Product or
at a website address indicated in the “About” section.
12.3 Service specific terms:
12.3.1 Online Search. By using the built in online search functionality the User hereby acknowledges that
during the search process the geographic position of the User’s device may be used for providing better
search results. Also the search result chosen by the User may be processed anonymously by the Service
supllier for statistical purposes.
When using the online search functionality the User may not (i) interfere with the performance of the
Service; (ii) complete mass downloads or bulk feeds of any content or information derived from the
Service or information acquired therefrom, use benchmarking methods, e.g., robots, to access or analyze
the Service or information derived therefrom, and (iii) alter or manipulate the Service or information
derived therefrom or modify the default settings operation or look and feel of the Service (including but not
limited to displayed logos, terms and notices); or (iv) use the Service or information derived therefrom in
connection with any unlawful, offensive, obscene, pornographic, harassing, libelous or otherwise
inappropriate content or material, furthermore (v) use search results to generate sales lead information in
the form of ASCII or other text-formatted lists of category-specific business listings which (x) include
complete mailing address for each business, and (y) contain a substantial portion of such listings for a
particular county, city, state, or zip code region.
12.3.2 Traffic. Neither the traffic information nor any derivatives thereof shall be used by the User for (i)
historical data purposes (including but not limited performing storage of the data in order to enable the
collection or analysis of information); or for (ii) broadcasting or making available to any third party; and (ii)
for the purpose of enforcement of traffic laws including but not limited to the selection of potential
locations for the installation of speed cameras, speed traps or other speed tracking devices.
Traffic data may not be archived and may only be delivered for Users’ near term personal use not to
exceed one twenty-four hour period.
13. Third party attribution
Attribution of third parties (e.g. copyright notices) supplying software modules, Databases, Services or
other material to the Navigation Product are listed in the “About” section of the Navigation Product or at a
website address indicated in the “About” section.
89
6 Copyright note
The product and the information contained herein are subject to change without prior notification.
This manual may not, in whole or in part, be reproduced or transmitted in any form either electronically or
mechanically, including photocopying and recording, without the express written consent of Alpine
Electronics, Inc.
© 2015 – Alpine Electronics, Inc. All rights reserved.
© 2015 – NNG Kft. All rights reserved.
Map data: © 1987 - 2015 HERE. All rights reserved. See http://corporate.navteq.com/supplier_terms.html.

Navigation menu