dormakaba Canada RB103 Remote Transmitter User Manual
dormakaba Canada Inc Remote Transmitter
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3845206 |
| Application ID | zmBR0HWDOI4MZMB1UmL+3g== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 26.96kB (337010 bits) |
| Date Submitted | 2018-05-10 00:00:00 |
| Date Available | 2018-05-10 00:00:00 |
| Creation Date | 2018-03-13 15:49:54 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2018-03-13 15:49:54 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CS6 (Macintosh) |
INSTALLATION 910TC-WRB Remote Receiver and Remote Transmitter The remote module allows wireless activation of the 910TC button for convenience or installations that do not allow for wire access. 1. Remove power to the unit prior to installing the remote receiver. (Fig.1) Fig. 1 5. On the back of the remote board, locate the button and LED as indicated below. (Fig.3) Fig. 3 2. Insert the pins of the remote board into the header of the button as indicated below. Ensure the pins are aligned and fully engaged in the header. (Fig.2) Fig. 2 6. Press and hold the button on the board until the red LED comes on, then release. 7. While the LED is lit press the button on the transmitter (Fig. 4), the LED will blink indicating the code is being stored. Fig. 4 8. The red LED will go out to indicate the storing of the code has been successful. Up to 5 transmitters can be paired with one receiver by following the above process. NOTE: Should you need to reprogram or delete a transmitter, all transmitters will be erased and need to be reprogrammed individually. 3. Reapply power to the unit. 4.Once installed the transmitter and receiver must be paired to each other for proper operation. 9. To erase all units, press and hold the button on the back of the board until the red LED comes on. Continue to hold the button until the LED goes out. 10. Repeat steps 6-8 to reprogram IS910TC-WRM-WRB © 2018 dormakaba Canada Inc. www.rutherfordcontrols.com • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • Email: sales_RCI@dormakaba.com R03-18TG-4 910TC-WRB FCC Regulatory Statements This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the Federal Communication Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer or an experienced radio/TV technician for help. NOTE: ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. ISED Regulatory Statements (For 910TC-WRB Only) This device complies with ISED Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme avec ISED Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. CAN ICES-3 (B)/NMB-3(B) © 2018 dormakaba Canada Inc. www.rutherfordcontrols.com • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • Email: sales_RCI@dormakaba.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2018:03:13 15:49:54-04:00 Metadata Date : 2018:03:13 15:49:54-04:00 Modify Date : 2018:03:13 15:49:54-04:00 Creator Tool : Adobe InDesign CS6 (Macintosh) Instance ID : uuid:644d4ac5-c33c-854f-836a-3aec101c2023 Original Document ID : xmp.did:0180117407206811A46CF74D571AED6E Document ID : xmp.id:F20F07B1B42168118083D2395B45B8E7 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:F10F07B1B42168118083D2395B45B8E7 Derived From Document ID : xmp.did:6F0DA4200A206811822ADBBB5B0C7B5A Derived From Original Document ID: xmp.did:0180117407206811A46CF74D571AED6E Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Macintosh) History Changed : / History When : 2018:03:13 15:49:54-04:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 2 Creator : Adobe InDesign CS6 (Macintosh)EXIF Metadata provided by EXIF.tools