dormakaba EAD RMS0001 RMS Mifare RFID Reader Module for Time and Attandance Terminal User Manual Integration Manual

Kaba GmbH RMS Mifare RFID Reader Module for Time and Attandance Terminal Integration Manual

Integration Manual

Download: dormakaba EAD RMS0001 RMS Mifare RFID Reader Module for Time and Attandance Terminal User Manual Integration Manual
Mirror Download [FCC.gov]dormakaba EAD RMS0001 RMS Mifare RFID Reader Module for Time and Attandance Terminal User Manual Integration Manual
Document ID1640391
Application IDobRIrBlOB0u5T826JMfuEw==
Document DescriptionIntegration Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize45.88kB (573447 bits)
Date Submitted2012-02-21 00:00:00
Date Available2012-02-21 00:00:00
Creation Date2011-10-24 10:25:48
Producing SoftwareAcrobat Distiller 9.0.0 (Windows)
Document Lastmod2012-02-20 16:36:23
Document TitleMicrosoft Word - NVI-RMS0001_RMS MiFare_03767_Installation Manual_Draft_sf-21-10-2011
Document CreatorPScript5.dll Version 5.2.2
Document Author: bowat-cl

Integration Manual for the Kaba MiFare RFID Reader
Module
FCC ID NVI-RMS0001
About this manual
Validity
This manual describes the MiFare RFID Reader Module into hosts, e.g. KABA B-web 93 00
Addressees
This manual is written exclusively for specialists.
The descriptions in this manual are intended for personnel trained by the manufacturer. The
information in this manual cannot substitute the product training.
The contents of this manual is intended for use by the following groups of people:





Project manager
Project manager who is responsible for the system and entrusted with project
planning and realization.
Fitter
Person specialized in mounting and installation.
Person who has an adequate technical training and sufficient experience and who
has been authorized by the manufacturer after completing the training on the product.
Service technician
Specialist for initial set-up and maintenance of the installation.
Person who has an adequate technical training and sufficient experience and who
has been authorized by the manufacturer after completing the training on the product.
Network administrator
Realizes the set-up of the device within the network and makes sure that the devices
are accessible within the network.
Software partner
Specialists for connecting the system to the user software by defining operating and
booking sequences, programming the customer applications and setting the
parameters of the devices.
NOTICE!
For reasons of device safety, some of the activities might only be carried out by the
SERVICE PERSON.
Only persons of the groups "Fitter" and "Service technician" have the status of a SERVICE
PERSON according to DIN EN 60950-1:2006.
Contents and purpose
The contents are limited to the assembly and installation of the hardware.
ESD (electro static discharge) protective measures
CAUTION



Danger for electronic components due to electrostatic discharge.
Improper handling of printed circuit boards or components can cause damages that
lead to complete failures or sporadic errors.
During installation and repair of the device, the ESD protective measures must be
considered.
Please consider the following guidelines before the installation or maintenance of the device:





Always carry an ESD antistatic wristband when dealing with electronic components.
Connect one part of the wristband with a discharge socket or an unvarnished
grounded metal component. This way, static charges are discharged from your body
securely and effectively.
Only touch the printed circuit boards at the edges. Do not touch the printed circuit
board itself or the connector.
Place all dismantled components on an anti-static surface or in an anti-static
container.
Avoid contact between printed circuit boards and your clothing. The wristband only
protects the printed circuit boards against electrostatic discharge from the body, but
there is still a risk of damage through electrostatic discharge from your clothing.
Transport and dispatch dismantled modules only in electrostatically shielded
protective bags.
Dimensions:
Description
The RMs Mifare is a RFID Reader/Writer with serial communication interface and a
illumination unit for lighting behind a symbol. The illumination module consists of an analog
current source, controlled by the Host-System via separate I2C Bus.
The RFID carrier frequency is 13,56MHz and the targeted RFID system is Mifare (ISO
14443).
The carrier frequency is derived from a 27.12 MHz quartz oscillator connected to the RFID
chip. Communication from reader to tag is done with ASK (Amplitude Shift Keying), from tag
to read with load modulation. Supported RFID data rates are 106kbit, 212kbit, 424kbit and
848kbit. Subcarrier frequency is 847.5kHz. Maximum antenna output current is 100mA. The
antenna design is symmetrical with an impedance of 40Ω according to Mifare datasheets.
Power is supplied from a Host-System (regulated and current limited 5VDC±5%.) with a
maximum current consumption of 550mA.
The device is intended to be mounted as a peripheral device via ribbon cable to a Hostsystem (e.g. KABA B-web 93 00).
The RMs Mifare includes a microcontroller with an 8MHz quartz oscillator. The
microcontroller controls the RFID Transceiver chip and a KABA specific security chip clocked
by 4MHz (half of the microcontrollers 8MHz).
The Host-System communicates via serial communication interface directly with the
microcontroller.
Integration into KABA B-web 93 00
Labeling
Using a permanently affixed label, the modular transmitter must be labeled with its
own FCC identification number, and, if the FCC identification number is not visible
when the module is installed inside another device, then the outside of the device
into which the module is installed must also display a label referring to the enclosed
module.
This exterior label can use wording such as the following: “Contains
Transmitter Module FCC ID NVI-RMS0001 or contains FCC ID NVI-RMS0001”. Any
similar wording that expresses the same meaning may be used.

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Author                          : bowat-cl
Create Date                     : 2011:10:24 10:25:48+02:00
Modify Date                     : 2012:02:20 16:36:23+01:00
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2012:02:20 16:36:23+01:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Format                          : application/pdf
Title                           : Microsoft Word - NVI-RMS0001_RMS MiFare_03767_Installation Manual_Draft_sf-21-10-2011
Creator                         : bowat-cl
Document ID                     : uuid:8e4e8d71-0a19-4b11-a5f3-f9f7918e9adf
Instance ID                     : uuid:588d56b0-0fc6-4ad5-a87f-3bb7cff729d3
Page Count                      : 5
EXIF Metadata provided by EXIF.tools
FCC ID Filing: NVI-RMS0001

Navigation menu