dormakaba EAD RMS0003 Module for Time and and Attandance Terminal User Manual intergration manual
Kaba GmbH Module for Time and and Attandance Terminal intergration manual
intergration manual
Integration Manual for the HIDprox RFID Reader Module
FCC ID NVI-RMS0003
About this manual
Validity
This manual describes the HIDprox RFID Reader Module into hosts, e.g. KABA B-web 93 00
Addressees
This manual is written exclusively for specialists.
The descriptions in this manual are intended for personnel trained by the manufacturer. The
information in this manual cannot substitute the product training.
The contents of this manual is intended for use by the following groups of people:
Project manager
Project manager who is responsible for the system and entrusted with project
planning and realization.
Fitter
Person specialized in mounting and installation.
Person who has an adequate technical training and sufficient experience and who
has been authorized by the manufacturer after completing the training on the product.
Service technician
Specialist for initial set-up and maintenance of the installation.
Person who has an adequate technical training and sufficient experience and who
has been authorized by the manufacturer after completing the training on the product.
Network administrator
Realizes the set-up of the device within the network and makes sure that the devices
are accessible within the network.
Software partner
Specialists for connecting the system to the user software by defining operating and
booking sequences, programming the customer applications and setting the
parameters of the devices.
NOTICE!
For reasons of device safety, some of the activities might only be carried out by the
SERVICE PERSON.
Only persons of the groups "Fitter" and "Service technician" have the status of a SERVICE
PERSON according to DIN EN 60950-1:2006.
Contents and purpose
The contents are limited to the assembly and installation of the hardware.
ESD (electro static discharge) protective measures
CAUTION
Danger for electronic components due to electrostatic discharge.
Improper handling of printed circuit boards or components can cause damages that
lead to complete failures or sporadic errors.
During installation and repair of the device, the ESD protective measures must be
considered.
Please consider the following guidelines before the installation or maintenance of the device:
Always carry an ESD antistatic wristband when dealing with electronic components.
Connect one part of the wristband with a discharge socket or an unvarnished
grounded metal component. This way, static charges are discharged from your body
securely and effectively.
Only touch the printed circuit boards at the edges. Do not touch the printed circuit
board itself or the connector.
Place all dismantled components on an anti-static surface or in an anti-static
container.
Avoid contact between printed circuit boards and your clothing. The wristband only
protects the printed circuit boards against electrostatic discharge from the body, but
there is still a risk of damage through electrostatic discharge from your clothing.
Transport and dispatch dismantled modules only in electrostatically shielded
protective bags.
Hardware
Features
Dimensions 100,0 x 50,0 x 10,0 (LxWxH) mm
Antenna on board
Interface type UART, TTL
Reading distance up to 50mm depending on tag
Power supply 5 VDC regulated
Dimensions:
Description
The RMs HIDprox is a RFID Reader/Writer with serial communication interface and
one illumination unit for lighting behind a symbol. The illumination module consists of
an analog current source, controlled by the Host-System via separate I2C Bus.
The RFID carrier frequency is 125kHz and the targeted RFID system is HIDeprox.
The carrier frequency is derived from a 8 MHz quartz oscillator. Communication from
reader to tag is done with ASK (Amplitude Shift Keying), from tag to read with load
modulation. Supported RFID data rates are 6.67kbit, 26.69kbit, 106kbit, 212kbit,
424kbit and 848kbit. The Subcarrier frequency is 423.75kHz, 484.28kHz and
847.5kHz.
Power is supplied from the Host-System (regulated, current limited 5VDC±5%.) with
a maximum current consumption of 550mA. The device is intended to be mounted as
a peripheral device via ribbon cable to a Host-system (e.g. KABA B-web 93 00).
Integration into KABA B-web 93 00
Labeling
Using a permanently affixed label, the modular transmitter must be labeled with its
own FCC identification number, and, if the FCC identification number is not visible
when the module is installed inside another device, then the outside of the device
into which the module is installed must also display a label referring to the enclosed
module.
This exterior label can use wording such as the following: “Contains
Transmitter Module FCC ID NVI-RMS0003 or contains FCC ID NVI-RMS0003”. Any
similar wording that expresses the same meaning may be used.
DECLARATION OF CONFORMITY
according to FCC Part 15
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.