Emerson 600 MCIM14006E 9884E Browning Standard Motor Base Instruction And Maintenance Manual R7 User 3ea79e69 F2b6 4e2c A632 3aa8b88f8b5f

User Manual: emerson 600 Emerson Outboard Motor 600 User Guide |

Open the PDF directly: View PDF PDF.
Page Count: 3

1
F O R M
Tenso-set™ Series 600
Auto-Tensioning Motor Base
Installation and Maintenance Manual
9884E
June 2014
Emerson Industrial Automation
7120 New Bufngton Road
Florence, KY 41042
Application Engineering: 800 626 2093
www.PowerTransmissionSolutions.com
CAUTION
• Periodic inspections should be performed. Failure to perform proper maintenance
can result in premature product failure and personal injury.
• All electrical work should be performed by qualied personnel and compliant with
local and national electrical codes.
WARNING
• Read and follow all instructions carefully.
• Disconnect and lock-out power before installation and maintenance.
Working on or near energized equipment can result in severe injury or death.
• Avoid contact with energized circuits or rotating parts.
• Be sure shaft key is fully captive before unit is energized.
• Do not operate equipment without guards in place. Exposed equipment can
result in severe injury or death.
Browning, Emerson and Emerson Industrial Automation are trademarks of Emerson
Electric Co. or one of its affiliated companies.
©2014 Emerson Power Transmission Corp., All Rights Reserved.
MCIM14006E • Form 9884E • Printed in USA
Motor Carriage
Tension Nut
Mounting Brackets
Tension Rod
Carriage Rods
Installation Instructions
1. Mount the motor on the motor base using the recommended
grade 5 bolts and torques listed in table 1.
Table 1
Motor Base Bolt Size Torque (Grade 5 plated )
BSAMBN601 5/16-18 13 Lb-Ft
BSAMBN605 3/8-16 23 Lb-Ft
BSAMBN607 3/8-16 23 Lb-Ft
BSAMBN613 3/8-16 23 Lb-Ft
BSAMBN621 1/2-13 57 Lb-Ft
BSAMBN623 1/2-13 57 Lb-Ft
2. Mount the sheaves on the Driver and Driven Shafts.
2
A
B
3. Mount the motor base using the recommended grade 5 bolts
(Leave the bolts loose enough to allow the motor base to be
moved to align the sheaves)
4. Set the motor base carriage to the center of the motor base
by adjusting the tension rod until dimension A and B are
equal.
5. Align the motor base to position the sheaves in the proper
location. A straight edge should be used to align the sheave
to be parallel and in the same plane. When this is achieved
the straight edge will be ush to the sides of both sheaves as
shown.
6. Tighten the motor base mounting bolts using the
recommended grade 5 bolts and torques listed in table 1.
7. Rotate the tension rod counterclockwise enough to allow the
belt to slip over the two sheaves by hand. (Prying the belts
over the sheaves with any device can damage the belts or
sheaves)
8. Manually pull the motor base back by hand in the direction
shown and rotate the tension rod clockwise until hand tight.
9. Use a wrench to tighten the tension rod turning clockwise
until the belt feels tight.
10. Check the belt tension using Browning Belt Tension Checker.
3
20°
20°
20°
20°
11. Adjust the tension screw until the proper belt tension is
recorded by the Browning Belt Tension Checker. The
recommended deection force is 150 percent of the Edge
value or the value given for a new belt in form 5453 included
with the Browning Belt Tension Checker
WARNING! The surface on which the Motor Base is mounted must be at. A base that is distorted or warped will not function
properly. If the surface is not at, correct the condition with shims.
Maintenance
Lubrication
The carriage tubes are provided with holes or tting for lubrication. Every six months or as dictated by the application, wipe down the
carriage rails and tension rod with an oily rag and apply a light grade grease. Be sure to remove all foreign material from the tubes
and tension rod.
Changing Belts
Turn the tension rod counter clockwise to move the carriage enough to allow the old belt to be removed.
Repeat steps 7 through 11 of the installation instructions to install the new belt.
Adjusting Belts
Periodic adjustment should not be needed. However, if it is suspected that the belt tension is not correct, then complete steps 10 and
11 of the installation instructions.
Allowable Mounting Positions
Floor Mounted Ceiling Mounted
Wall Mounted Driven
beside Driver
Browning, Emerson and Emerson Industrial Automation are trademarks of Emerson
Electric Co. or one of its affiliated companies.
©2014 Emerson Power Transmission Corp., All Rights Reserved.
MCIM14006E • Form 9884E • Printed in USA
Wall Mounted Driven
Above Driver
All other mounting positions contact Application Engineering.

Navigation menu