Grizzly G1515 G1083 1370 Instructions User Manual 63c4e3ac 2a79 5b94 7d26 85cc1c45a7ad
User Manual: grizzly g1515 Grizzly Drill G1515 User Guide |
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
MODEL G1083, G1370, G1514, G1515 MORTISING ATTACHMENT INSTRUCTIONS The mortising attachment enables you to cut square mortises in wood stock with a drill press and matched mortising chisel and bit. Material is removed by the mortising bit and the mortising chisel simultaneously squares the hole. The mortising attachment consists of a fence that mounts to the drill press table, two hook clamps that secure the work against the fence, an adjustable hold–down that keeps the work from raising when the chisel is raised and a chisel holder. The chisel holder has a split casting that clamps to the drill press quill. The chisel holder will accept a variety of mortising chisel sizes. Securing Mortising Attachment to Drill Press 1. Swing the drill press table away, lower the quill and lock in place. Slide the chisel holder onto the quill and tighten the bolt on the chisel holder split casting. Mortising 1. Mark your mortise on the workpiece. Without drilling any stock, check the chisel position against the layout line. Make adjustments as required. 2. Remove the workpiece from under the mortising chisel and adjust the spindle stop to the desired depth. Crank the spindle down to make sure everything is clear. 3. Position the hook clamps against the side o the workpiece. 4. Adjust he hold-down so it is just above the workpiece and secure into position with the lock knob. 5. For best results, select a drill press speed of 650 to 1000 RPM. 6. Cut mortises in sequence as shown above. The distance between position 1 and 2, 2 and 4 and so on should be less than the width of the mortising chisel. 2. Slide a desired mortising chisel into the end of the chisel holder and secure. 3. Slide the matching mortising bit through the chisel and into the drill chuck. The tip of the mortising bit should be at least 1⁄16" below the edge of the chisel. NOTE: It may be necessary to cut or grind the end of the bit that fits into the chuck so there will be proper clearance below the edge of the chisel. Secure the bit in the drill chuck. 4. Fasten the fence assembly to the table. Ensure that the fence is positioned so it is square to the side of the chisel and set at the desired distance from the back of the chisel. Sharpening The mortising bit and chisel must be periodically re-sharpened. Sharpen mortising chisels with a round slipstone, working from the inside of the chisel to the edge. Do not sharpen the outside edge. Any burr on the outside edge of the chisel caused by sharpening the inside must be removed with a flat stone. Sharpen the mortising bit with a flat stone or triangular file. COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC. REVISED OCTOBER, 2007 (TR) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #BA0520 PRINTED IN TAIWAN � ��� ��� ��� � ���� ��� � � ���� ���� ���� ���� ���� ������������������������� ���������������������� �� � � � � � � � � � � REF PART # DESCRIPTION 1 1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 13-1 13-2 13-3 13-4 13-5 CONE 2-19/32 - 66MM CONE 2-3/8'' CONE 1-5/8'' CONE 1-7/8'' HEX BOLT 5/16-18 X 2-1/2 HEX NUT 5/16-18 KNOB HOLD DOWN CASTING HEX BOLT 5/16-18 X 4-1/2 FLAT WASHER 5/16 ROD BRACKET HOLD DOWN ROD FENCE WING NUT 5/16-18 SET OF 5 CHISELS MORTISING CHISEL - 1/4" MORTISING CHISEL - 5/16" MORTISING CHISEL - 3/8" MORTISING CHISEL - 1/2" MORTISING CHISEL - 5/8" P1083001 P1370001 P1514001 P1515001 PB23 PN02 P1083004 P1083005 PB30 PW07 P1083008 P1083009 P1083010 P1083011 PWN03 P1083013 P1083013-1 P1083013-2 P1083013-3 P1083013-4 P1083013-5 � �� �� �� �� ��
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : Yes Page Count : 2 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:816c213a-71cd-11dc-ba8c-000393c83c9a Create Date : 2007:10:03 07:41:38Z Creator Tool : Adobe InDesign CS (3.0.1) Metadata Date : 2007:10:03 09:27:16-07:00 Modify Date : 2007:10:03 09:27:16-07:00 Rendition Class : proof:pdf Document ID : adobe:docid:indd:54a6ffdb-7231-11dc-afd1-8f8c6dfc35f3 Manifest Link Form : ReferenceStream, ReferenceStream Manifest Reference Instance ID : uuid:a599d0da-71c5-11dc-bdc6-000393c83c9a, uuid:502fbfa6-71c7-11dc-bdc6-000393c83c9a Manifest Reference Document ID : uuid:a599c0ba-71c5-11dc-bdc6-000393c83c9a, uuid:502faf01-71c7-11dc-bdc6-000393c83c9a Format : application/pdf Title : G1083 1370 Instructions.indd Trapped : False Creator : Adobe InDesign CS (3.0.1) Producer : Adobe PDF Library 6.0EXIF Metadata provided by EXIF.tools