iKeyless ARX11B2 Keyless Remote User Manual 16 3048 Manual
iKeyless, LLC Keyless Remote 16 3048 Manual
iKeyless >
Manual
2320 Presidential Drive, Suite 101, Durham, NC 27703 USA Voice: 919-381-4235
Certification Exhibit
FCC ID: X32-ARX11B2
IC: 8797A-ARX11B2
FCC Rule Part: 15.231
IC Radio Standards Specification: RSS-210
ACS Project Number: 16-3048
Manufacturer: iKeyless, LLC
Model: 300-0388
Manual
300-0388
Draft User Manual
2016-06-03
Remote Layout
Seven Function Buttons:
1. Panic
2. Door Unlock
3. Door Lock
4. Trunk/Hatch Unlock
5. Remote Start
6. Driver Door Open
7. Passenger Door Open
2
1
2
3
4 5
6 7
Using the remote
Make sure you’re within range of the vehicle before attempting to use the remote.
● To activate the vehicle panic alarm, press and release the panic button. To deactivate the
vehicle panic alarm, press any button on the remote.
● To use the unlock feature, press and release the unlock button.
● To use the remote lock feature, press and release the lock button.
● To use the trunk unlock/hatch release feature press the trunk/hatch unlock button.
● To use the remote start feature, press and release the start button.
● To use the driver door open feature, press and release the driver door open button.
● To use the passenger door open feature, press and release the passenger door open button.
Note: The exact behavior in response to each button press may vary depending on the vehicle.
Consult the vehicle manual for more information.
3
Changing the CR2032 battery
1. Remove the valet key by sliding the latch on the top of the Fob sideways
with your thumb and pulling on the key with your finger.
2. Insert the tip of the valet key into the key slot and pry apart the two halves
of the shell of the Fob.
3. Replace the CR2032 battery making sure to put the + side of the battery
towards the back half of the Fob shell.
4. Press the two shell halves back together and replace the valet key.
4
FCC/IC Label
5
The FCC/IC label is
located on the back
cover of the remote.
FCC Regulatory Statement
Model: 300-0388
FCC ID: X32-ARX11B2
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this device not expressly approved by (iKeyless LLC) could void the user’s
authority to operate the equipment.
6
IC Regulatory Statement
Model: 300-0388
IC: 8797A-ARX11B2
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio
interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies
with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent appareil est conforme
aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement. 7