iKeyless MTHKG000 Keyless Entry Remote User Manual Manual
iKeyless, LLC Keyless Entry Remote Manual
iKeyless >
Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3880902 |
| Application ID | eVZTDzEvvXAR8DCXP3dmzg== |
| Document Description | Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 118.66kB (1483281 bits) |
| Date Submitted | 2018-06-08 00:00:00 |
| Date Available | 2018-06-08 00:00:00 |
| Creation Date | 0000-00-00 00:00:00 |
| Document Lastmod | 0000-00-00 00:00:00 |
| Document Title | Manual |
| Document Creator |
MTHKL-G000 User’s Guide iKeyless LLC Confidential Button Functions UNLOCK: Used for one’s selection LOCK: Used for hundred’s selection TRUNK: Not used for programming PANIC: Used for ten’s selection iKeyless LLC Confidential Programming Procedure To enter programming mode, press and hold LOCK and PANIC simultaneously. LED will illuminate steadily Enter activation code. For example, code 242 would be entered by; 242, pressing LOCK twice 242, pressing PANIC four times 242, pressing UNLOCK twice LED will blink with each button press To exit programming mode, again press and hold LOCK and PANIC simultaneously. If a valid code was entered, LED will blink once. If an invalid code was entered, LED will blink three times. If no code is entered after a time, LED will blink and key will exit programming mode automatically. iKeyless LLC Confidential Battery Replacement Using a small screwdriver, pry open outer shell Inner Shell Remove inner shell Using small screwdriver, pry open inner shell CR1620 Replace CR1620 battery with positive terminal down Press inner shell together, replace in outer shell, then press outer shell together iKeyless LLC Confidential Using the Remote FCC Regulatory Statement Model: MTHKL-G000 FCC ID: X32-MTHKG000 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this device not expressly approved by iKeyless, LLC could void the user’s authority to operate the equipment. IC Regulatory Statement Model: MTHKL-G000 IC: 8797A-MTHKG000 Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Warning : Root object (4 0 obj) not found at 16EXIF Metadata provided by EXIF.tools