iLuv Creative Technology BBGAIR BBGUMAIR User Manual
iLuv Creative Technology BBGUMAIR
User Manual
1.Press and Hold Multifunction button 1 Second , comes from then promotes " Power On" , LED
lights up , unit goes into Discovering mode, Blue LED switch to fast flashing ( 2times /s)
2.Press and Hold Multifunction button 3 Seconds , comes from Speaker then promotes " ready to
pair ", unit goes into "Pairing" mode, Blue LED switch to Blue/Red flashing alternately ( 2times /s)
3.Touch and click Headset name in device blue tooth setting menu, comes from Speaker then
promotes " device is connected" , unit paired sucessfuly , Blue LED switch to slow flashing
( 4seconds /time)
4.If Music player app opened, after paired with speaker , Music start play directly。On
paired mode, Open apps , Press multifunction button on headset to start play, Press again, Pause
playback。Press and Hold“VOL+”button, skip to next song, Press and Hold“VOL-”button go back
to last song。Press “VOL+/VOL-”button repeatedly to adjust volume ,Volume will go to maximum
or minimum ,and a voice prompt"DiDi/maximum volume".
5.When incoming call received , The phone ringing or voice prompt"incoming call " , LED switch
to fast flashing 2 times/second.When incoming call received , Press and Multifunction button to
pick up , Blue LED switch to slow flashing ( 1time /s), Press the same button again to hang
up.During hand free conversation . During hand free conversation , Press and Hold “VOL-”button
to mute the sounds , Press and Hold “VOL-”button to cancel mute and go back
conversation.During hand free conversation , Press “VOL+/VOL-”button repeatedly to adjust
volume ,Volume will go to maximum or minimum ,and a voice prompt"DiDi/maximum
volume".Double click multifunction button , Redial the last dialed number, voice prompt:（last
number redialed）
6.When incoming call received, Press and Hold multifunction button 1 second Drip hint sound
comes from speaker and voice prompt"calling rejected"
7.In case conference is on, another call is incoming ,Double click multifunction button to hang up current
call and pick up new incoming call; Short press multifunction button to pick up new call also keep
current conference ;press multifunction button to Switch new and current conference call ;
8.press multifunction button to Switch new and current conference call
9.On Standby and playing music mode, Press and Hold Multifunction button 1Second , unit goes
into Voice control mode ,"Di" tone prompt
10.Press and Hold Multifunction button 5 Second , Speaker promotes then say " Power Off" , Red
LED flashing 3 times then goes off
11.When battery level is below preset value ( 3.3V of rating ), Red LED start to flashing
slowly (one time in every 20 seconds), Speaker promotes " Di " tone then say " Battery low " in
every one minitue.
12.During charging battery, Red LED keeps solid ON, and Blue LED lighs up once battery is full
charged .
13.
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. This equipment has been tested and found to comply
with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following
measures:
‐ Reorient or relocate the receiving antenna.
‐Increase the separation between the equipment and receiver.
‐ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
‐ Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to
meet general RF exposure requirement. The device can be used in portable exposure condition without
restriction.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.