ip access IPA219C 3G Picocellular basestation User Manual nano3GAP Installation Manual

ip.access ltd 3G Picocellular basestation nano3GAP Installation Manual

UserManual.wiki >

ip access >

IPA219C User Manual >

Installation guide HTML Version

Installation guide

nano3GAP Installation Manual

N3G_INST_300 2.0 ip.access Ltd

Building 2020

Cambourne Business Park

Cambourne

Cambridgeshire CB23 6DW

United Kingdom

www.ipaccess.com

nano3GAP Installation Manual

Revision History

Version Change Summary Date Author

0.1 First draft 29 Apr 09 ZN1

0.2 Updated from feedback 06 May 09 ZN1

0.3 Updated from further feedback 07 May 09 ZN1

0.4 Updated from review comments 08 May 09 ZN1

0.5 Added license texts, updated with minor comments 12 May 09 ZN1

0.6 Updated the instructions on deployment commissioning 05 Jun 09 ZN1

0.7 Updated with input from System Testing 24 Jul 09 ZN1

0.8 Updated from feedback from System Testing 27 Jul 09 ZN1

0.9 Added instructions to changing the IP configuration of the

commissioning PC

27 Jul 09 ZN1

0.10 Implemented review comments 28 Jul 09 ZN1

0.11 Minor corrections before approval 29 Jul 09 ZN1

1.0 Released for N3G_1.1 29 Jul 09 ZN1

1.1 Added information on type approval and EMC standards

Updated information on electrical ratings and PSUs

28 Aug 09 ZN1

1.2 Implemented review comments 28 Aug 09 ZN1

2.0 Released for N3G_1.1_UPGRADE 28 Aug 09 ZN1

Approved by e-mail.

The information contained in this manual is commercially confidential and must not be

disclosed to third parties without prior consent.

nano3GAP Installation Manual

Table of Contents

1 Introduction ..................................................................................................... 1

1.1 Installation Overview......................................................................................... 1

1.2 Related Information........................................................................................... 1

1.3 Terminology ...................................................................................................... 2

2 Installation Requirements .............................................................................. 3

2.1 nano3GAP Site Requirements.......................................................................... 3

2.1.1 nano3GAP-4 Site Requirements............................................................................ 3

2.2 Installation Tool Requirements ......................................................................... 6

2.3 Information Needed for Installation ................................................................... 7

2.3.1 Network Information ............................................................................................... 7

2.3.2 AP Configuration File ............................................................................................. 7

3 nano3GAP Hardware Installation .................................................................. 8

3.1 Warnings and Regulatory Information .............................................................. 8

3.2 Hardware Installation - nano3GAP-4 ................................................................ 8

3.2.1 Unpacking the nano3GAP-4 .................................................................................. 8

3.2.2 Mounting the nano3GAP-4..................................................................................... 8

4 Deployment Commissioning of the nano3GAP ......................................... 11

4.1 Configure the IP Settings of the Provisioning Laptop ..................................... 11

4.2 Configure the Connection to the AP ............................................................... 12

4.3 Set the IP Configuration of the AP .................................................................. 14

5 Configuration of the nano3GAP-4 from the OMC-R................................... 15

5.1 Start the OMC-R Client ................................................................................... 15

5.2 Download the Latest nano3GAP-4 Software Image ....................................... 17

5.3 Create an Attribute Configuration File for the AP............................................ 17

5.4 Download the Attribute Configuration to the AP ............................................. 18

5.5 Perform AP-specific Configuration.................................................................. 18

5.6 Bring the AP into Service ................................................................................ 18

6 Troubleshooting............................................................................................ 19

6.1 Internet Connection Problems ........................................................................ 19

6.2 LED Status Indicators ..................................................................................... 19

6.3 Factory Reset.................................................................................................. 20

nano3GAP Installation Manual

7 nano3GAP and PSU Regulatory Information ............................................. 21

7.1 Warnings and Cautions................................................................................... 21

7.2 Regulatory Statements ................................................................................... 22

7.2.1 Type Approval and EMC Standards .................................................................... 22

7.2.2 Safety Standards.................................................................................................. 23

8 Appendices.................................................................................................... 24

8.1 Appendix A - Example AP Configuration File ................................................. 24

8.2 Appendix B - Licenses and Copyright Notices................................................ 25

8.2.1 asn1c.................................................................................................................... 25

8.2.2 bash...................................................................................................................... 25

8.2.3 BusyBox ............................................................................................................... 25

8.2.4 cramfs................................................................................................................... 25

8.2.5 dropbear ............................................................................................................... 26

8.2.6 glibc ...................................................................................................................... 26

8.2.7 gmp ...................................................................................................................... 26

8.2.8 ipkg....................................................................................................................... 26

8.2.9 iproute2 ................................................................................................................ 26

8.2.10 iptables ................................................................................................................. 26

8.2.11 libcurl .................................................................................................................... 26

8.2.12 libgcc .................................................................................................................... 27

8.2.13 libpcap .................................................................................................................. 27

8.2.14 libxml2 .................................................................................................................. 27

8.2.15 Linux Kernel ......................................................................................................... 27

8.2.16 mtd.utils ................................................................................................................ 27

8.2.17 ncurses................................................................................................................. 28

8.2.18 NTP daemon ........................................................................................................ 28

8.2.19 pcre ...................................................................................................................... 28

8.2.20 procps................................................................................................................... 30

8.2.21 SSL Stack............................................................................................................. 30

8.2.22 StrongSwan.......................................................................................................... 30

8.2.23 TCL....................................................................................................................... 30

8.2.24 tcpdump................................................................................................................ 31

8.2.25 thttpd .................................................................................................................... 31

8.2.26 U-Boot .................................................................................................................. 31

8.2.27 zlib ........................................................................................................................ 31

8.2.28 General Licenses ................................................................................................. 31

nano3GAP Installation Manual Introduction

1 Introduction

The ip.access nano3GAP-4 is an indoor pico-class base station.

This document provides the reader with all the necessary information required to install the

ip.access nano3GAP-4. The document provides step-by-step instructions for hardware

installation, PSU Installation, and configuration steps required to bring the nano3GAP-4

into service.

The AP can be configured with a static IP address or it can obtain its IP address

dynamically via DHCP. The AP-AC connection can be configured to be secure (via IPSec)

or unsecured.

1.1 Installation Overview

The principal activities for installing and commissioning a nano3GAP are:

1) Install the nano3GAP hardware and power it up (installation engineer on site,

section 3).

2) Commission the nano3GAP for connecting to an AC and OMC-R (installation

engineer on site, section 4).

3) Configure the nano3GAP from the OMC-R to bring it to into service (OAM

engineer remotely from the NOC, section 5).

1.2 Related Information

[GST_100] nano3G System Overview Manual (N3G_GST_100)

[GST_120] nano3G System Planning and Provisioning Manual (N3G_GST_120)

[GST_300] nano3GAP Product Description (N3G_GST_300)

[GST_400] nano3G OMC-R Product Description (N3G_GST_400)

[INST_200] Nano3G AC Installation Manual (N3G_INST_200)

[INST_400] nano3G OMC-R Installation Manual (N3G_INST_400)

[OPM_300] nano3GAP Operations Manual (N3G_OPM_300)

[OPM_410] nano3G OMC-R Client Operations Manual (N3G_OPM_410)

[OPM_430] nano3G OAM File Server Operations Manual (N3G_OPM_430)

[REF_105] nano3G System Glossary (N3G_REF_105)

[REF_150] Iu+ Networking Reference Manual (N3G_REF_150)

[21.905] Vocabulary for 3GPP Specifications, 3rd Generation Partnership Project

nano3GAP Installation Manual Introduction

1.3 Terminology

For standard nano3G System terminology, see [REF_105].

For additional standard GSM terminology, see [21.905].

nano3GAP Installation Manual Installation Requirements

2 Installation Requirements

2.1 nano3GAP Site Requirements

2.1.1 nano3GAP-4 Site Requirements

The nano3GAPs are installed in retail or small office environments. In summary, each AP

will require:

• One of:

o A suitable mains power supply point within [1.5] metres of the intended AP

site.

o Power over Ethernet (where mains power is remote).

• An Ethernet connection that provides an IP address (via static addressing or via

DHCP) and a route to the public Internet. A DNS service is also required to

resolve symbolic addresses.

• Site for wall mounting or a stable free-standing position.

• Cat5 cable.

2.1.1.1 Power

Maximum expected power consumption: 13 Watts (Rated 9VDC 1450mA)

The nano3GAP-4 supports the following power and Ethernet cabling options at a site:

• Direct power from a power adapter

• Power-over-Ethernet

o from a POE switch

o from a POE inserter

nano3GAP Installation Manual Installation Requirements

The connections are shown in the figure below.

nano3GAP-4 Ethernet and power connections

The power adapter, as well as the POE inserter and splitter supplied by ip.access comply

with LPS requirements in accordance with IEC/EN 60950-1.

Power Adapter

A suitable mains power supply point into which the power adapter for the AP can be

plugged. This should be within [1.5] metres of the intended installation position of the AP.

Only use the power adapter supplied by ip.access to power the AP:

ip.access part number EPS1173R

manufactured by Dee Van Enterprise Co Ltd.

model DSA-20P-10

input 100-240V ~ 50/60Hz 0.7A

output +9VDC 1.67A

Power over Ethernet

POE comprises of a power inserter and a splitter. The power inserter is positioned close to

the Internet connection, while the splitter is positioned close to the AP.

Only use the POE inserter supplied by ip.access:

ip.access part number 109A

manufactured by PPI Co Ltd

model ILA1711112

input 100/230V ~ 60/50Hz 0.5/0.25A

output 48VDC 0.38A

nano3GAP Installation Manual Installation Requirements

POE inserter

Only use the POE splitter supplied by ip.access:

ip.access part number 222A

manufactured by MIT

model MIT-061-1209-IP

input 48VDC 0.35A

output 9VDC 1.33A

POE splitter

nano3GAP Installation Manual Installation Requirements

2.1.1.2 Physical

The nano3GAP may be installed in the following ways:

• free-standing on a flat stable surface (section 3.2.2.1)

• attached to a wall or partition using the two screws which engage in keyhole slots

in the rear surface of the AP (section 3.2.2.2)

• attached to a POE splitter using the two screws which engage in keyhole slots in

the rear surface of the AP; the POE splitter in turn attaches to a wall or partition

using two screws (section 3.2.2.3)

Attention should also be paid to ensuring free air circulation around the unit. The unit must

be vertical.

It is recommended that the AP is installed with its front surface facing the area requiring

cellular coverage, unobscured by walls or partitions that may have significant RF

attenuation.

Height 176 mm (without stand)

193mm (with stand)

Width 170 mm

Depth 51 mm

Dimensions and

Weight

Approximate Weight 0.42 Kg (AP only)

Cooling Vents on the back at top and bottom

Operating Temperature 0°C to 40°C

Environmental

Operating Humidity 10 to 70% non-condensing

2.1.1.3 IP Bandwidth Requirements

At maximum capacity, a 4-Channel nano3GAP will require:

• downlink: at least 5Mbps

• uplink: 512kbps

This will deliver up to 4 voice calls and HSDPA services up to 3.6Mbps.

2.2 Installation Tool Requirements

• To mount the POE splitter or the AP onto the wall:

o 2 self tapping pan head screws, size No. 6 (approx 3.5mm (0.14in) in

diameter)

o suitable drills, screwdriver, etc.

• Provisioning laptop:

o OS: Windows XP

o web browser: Microsoft Internet Explorer 7

nano3GAP Installation Manual Installation Requirements

o JavaScript enabled in the web browser

2.3 Information Needed for Installation

2.3.1 Network Information

Installation Engineer:

• subnet information: the installation laptop and the nano3GAP-4 to be configured

must be on the same subnet

• username and password for the AP web server

• address of the security gateway

• address of the serving 3G AC

• ID of this AP on the serving 3G AC

• CRL and NTP server addresses

• DHCP or static IP

• if IPSec is used: Traffic Selector information (IP address and subnet mask)

NOC Engineer:

• Username and password to the OMC-R

• The valid URL to the latest AP software image on the OAM File Server

• Configuration file to be used in the OMC-R Load Attributes Wizard (nano3GAP-4s

hold the master copy of their own configuration and are not pre-provisioned via

the OMC-R)

• Configuration data for the AP:

o MCC

o MNC

o LAC

o SAI

o SAC/LAC

o UARFCN

o Scrambling code

o RNC ID

o RAC

2.3.2 AP Configuration File

Create a separate attributes file for each AP to commission (section 5.3).

nano3GAP Installation Manual nano3GAP Hardware Installation

3 nano3GAP Hardware Installation

This section documents the procedure used to install the nano3GAP-4 hardware and

physical connections together with applying the base software configuration.

3.1 Warnings and Regulatory Information

For all warnings and regulatory information, refer to section 7.

3.2 Hardware Installation - nano3GAP-4

3.2.1 Unpacking the nano3GAP-4

1) Unpack the nano3GAP-4, the stand and the POE splitter unit.

Note: No screws are supplied to mount the AP or the splitter unit.

2) Check that the items have not been damaged in transit.

Any damaged units should be returned to the supplier.

3.2.2 Mounting the nano3GAP-4

Note: The nano3GAP-4 should be installed in a position so that it is at least 2m away from the

area where handsets are normally used.

The nano3GAP-4 can be mounted in the following ways:

• on a stand

• directly onto the wall at or above head height

• onto the splitter unit at or above head height

The nano3GAP-4 has 2 holes at the back for the latter two mounting options:

nano3GAP Installation Manual nano3GAP Hardware Installation

3.2.2.1 Mounting the nano3GAP-4 on a Stand

1) Plug the Ethernet cable and the power cable into the AP.

2) Slide the AP onto the stand.

3) Place the stand with the AP onto a stable flat surface.

nano3GAP-4 mounted on a stand

3.2.2.2 Mounting the nano3GAP-4 directly onto the wall

1) Drill two holes 70mm (2.76in) apart vertically for the two screws.

2) Insert wall plugs (if required) and secure the screws leaving approximately 3mm

(0.12in) clearance between the screw heads and the wall.

3) Plug the Ethernet cable and the power cable into the AP.

4) Slide the AP onto the 2 screws.

nano3GAP-4 mounted directly on the wall

nano3GAP Installation Manual nano3GAP Hardware Installation

3.2.2.3 Mounting the nano3GAP-4 onto the splitter unit on the wall

1) Secure the splitter unit to the wall using two screws.

Ensure that the Ethernet socket is at the top.

2) Plug the Ethernet cable into the splitter unit.

3) Plug the Ethernet cable and the power cable coming from the splitter unit into the

AP.

4) Mount the AP onto the 2 screws that are already fixed onto the splitter unit.

nano3GAP-4 mounted on the POE splitter

nano3GAP Installation Manual Deployment Commissioning of the nano3GAP

4 Deployment Commissioning of the nano3GAP

Deployment commissioning is performed typically on site, with a provisioning laptop.

The nano3GAP-4 must be in factory reset status for the commissioning. For instructions on

performing a factory reset, see section 6.3.

4.1 Configure the IP Settings of the Provisioning Laptop

1) Open the control panel on the laptop.

2) Select Network Connections, select the relevant Local Area Connection, then

right-click Properties.

The following Dialog box appears:

nano3GAP Installation Manual Deployment Commissioning of the nano3GAP

3) Select Internet Protocol (TCP/IP) and then click Properties.

The following Dialog box appears:

4) Change the properties to Use the following IP address.

5) Set the IP Address to 192.168.0.2.

6) Set the Subnet Mask to 255.255.255.0.

Note: The provisioning laptop and the AP must be in the same subnet.

7) Click OK and close the two dialog boxes.

4.2 Configure the Connection to the AP

8) Connect the AP to the Ethernet interface of the provisioning laptop via an

Ethernet cable.

9) Apply power to the AP.

10) Start a web browser on the laptop.

11) Enter the pre-defined static IP address for the web server: 192.168.0.1.

A login screen appears.

nano3GAP Installation Manual Deployment Commissioning of the nano3GAP

12) Enter the commissioning username and the password (supplied separately).

The default page (Connection Configuration) appears.

13) Edit the configuration information:

It is recommended to leave the default NTP server address as default.

Note: The CRL Server Base URL is embedded in the IPSec Gateway address

in the current release. Therefore, this field will be left empty.

14) Save the configuration by clicking Apply Changes.

15) Start the AP in normal operation mode by clicking Complete Commissioning.

16) When the initial configuration is completed, power off the AP and disconnect it

from the laptop.

17) Mount the AP at its intended location, see section 3.2.2.

18) Connect the AP to the operator network and apply power.

The AP performs its normal, deployed mode start-up and connects to its host AC:

During this procedure, the nano3GAP-4 obtains network time and day information

from the NTP server and – if IPSec is in use – it establishes an IPSec tunnel to

the Security Gateway.

From this point on, the AP can be managed from the OMC-R. It is now ready for initial

configuration by NOC engineers, see section 5.

nano3GAP Installation Manual Deployment Commissioning of the nano3GAP

4.3 Set the IP Configuration of the AP

19) Click the IP Config link on the left of the screen.

20) Edit the parameters as needed and then click Apply.

21) Click the Connection Config link on the left of the screen and then click

Complete Commissioning.

22) Read the warning and click OK to complete commissioning.

nano3GAP Installation Manual Configuration of the nano3GAP-4 from the OMC-R

5 Configuration of the nano3GAP-4 from the OMC-R

The nano3GAP-4 needs to be configured before it is brought into service. The NOC

engineer must perform the configuration via the OMC-R Client.

5.1 Start the OMC-R Client

The OMC-R Server provides a web page to start the OMC-R Client.

1) Start a web browser application.

2) Enter the URL for the OMC-R server’s web page as:

http://<server-hostname>/omcr

Where <server-hostname> is the fully qualified hostname of the OMC-R server.

Note: This assumes that DNS is correctly configured on the management

network: the OMC-R server can be found by using its host name from

client computers on the same network.

Note: If a redundant configuration is used, the IP address entered here is a

virtual IP address that will ensure that the connection to the active OMC-

R Server can be set up without further actions from the client.

3) Press the Enter key and the OMC-R web page will appear.

nano3GAP Installation Manual Configuration of the nano3GAP-4 from the OMC-R

4) If it has not been installed on the client computer, click the link to download and

install the Java runtime (JRE version 1.5) for Windows®. This will allow a

Windows® client computer to run the OMC-R Client.

Note: When installed on Windows®, the JRE may automatically update to

version 1.6. The OMC-R Client will operate correctly with JRE 1.6.

However, do not install any version later than 1.6 (or allow JRE to be

automatically updated; for example, decline the update if prompted). The

Java Control Panel may be used to disable automatic updates and/or

disable usage of JRE versions later than 1.6.

5) The OMC-R Client is automatically installed when it is started. Click the link or

icon for Start 3G OMC-R Client.

If this is the first time the OMC-R Client has been started from this client

computer, or if the client version on the OMC-R Server has been updated, the

client application will download (which also installs the application).

If a security warning appears about verification of the digital signature for the

application, click the Run button.

6) The OMC-R Client will initialize and connect to the OMC-R Server. A login prompt

will appear. The first time the client is used from a particular computer, the User

name will be set to the log in ID used for the current session on the client

computer.

7) Enter the username and password, then click OK. The user name will be

remembered at the next login.

8) The OMC-R Client will initialize and connect to the OMC-R Server. The following

screen appears:

nano3GAP Installation Manual Configuration of the nano3GAP-4 from the OMC-R

9) Double-click through the tree (Management Views > Configuration Management)

to navigate to the AP to configure.

5.2 Download the Latest nano3GAP-4 Software Image

If the AP already has the latest software version, skip this section.

The latest software image is downloaded to the AP from the OAM File Server. For

instructions about how the software images are uploaded to the OAM File Server, see

[OPM_430].

10) Make sure that you have the URL to the latest software image file (SDP file)

stored on the OAM File Server.

11) Select the AP in the OMC-R Client.

12) Right-click the AP, select Actions and then Perform Software Download.

13) In the Perform Software Download Actions window, enter the URL of the latest

SDP file.

14) Select whether the image file should be downloaded only, or it should be

swapped with the older image file, and whether the older image file should be

removed from the standby folder on the AP.

15) Click Finish.

The download in progress is indicated by the flashing network LED on the AP.

16) Monitor the 3G AP Admin Package of the AP object in the OMC-R Client.

17) When the standby software version is the version of the downloaded image, right-

click the AP, select Action, and then select Swap Default Software.

18) Right-click the AP object again and then select Reinitialize.

19) Wait for the AP to be shown as connected to the OMC-R.

20) In the 3G AP Admin Package of the AP object, check that the Active Software

Version is that of the new SDP.

5.3 Create an Attribute Configuration File for the AP

The attributes to configure a nano3G-4 AP are stored in a text file. The file can be created

and edited manually in any text editor. For a sample file, see section 8.1.

To create the configuration file by using an existing one:

21) Log in to the OMC-R (see section 5.1).

22) Start the OMC-R Load Attributes Wizard: right-click on any existing AP object in

the OMC-R Client and then select Save Attributes to File.

23) Save the file under a new name.

24) Edit the file in a text editor.

nano3GAP Installation Manual Configuration of the nano3GAP-4 from the OMC-R

5.4 Download the Attribute Configuration to the AP

25) Ensure that the attribute configuration file is available on the configuration PC or

at a location reachable from the configuration PC. For information on the AP

configuration file, see section 8.1.

26) Log in to the OMC-R (see section 5.1).

27) Start the OMC-R Load Attributes Wizard: right-click on the AP object in the OMC-

R Client and then select Load Attributes From File.

28) Browse to the configuration file and click Apply to load and apply the

configuration settings.

If any of the loaded values are inconsistent with the current state of the AP or if

any of the values are illegal, the wizard displays a warning.

5.5 Perform AP-specific Configuration

29) Perform any AP-specific configurations. In particular, check and modify the

attributes of the following packages as needed:

o Network Listen Control Package

Note: Ensure that the Neighbour List Population attribute is set to Static

Only.

Note: Ensure that the Scan Interval attribute in the package RF Scan Control

is set so that the NWL scan does not disrupt the service. Scheduled NWL

scans should be timed for low-usage time slots. NWL scans can be also

disabled by setting the Scan Interval attribute to 0. In this case, the NWL

scan can be run manually at any time, see the next step.

o Cell Package

o NAS Package

o Location Package

30) Run a Network Listen scan: right-click the AP object, select Actions and then

select Start Sequential NWL Scan.

31) Ensure that the oscillator frequency is correct: select Actions and then select

Apply Frequency Correction.

5.6 Bring the AP into Service

32) Unlock the AP to bring it into service.

The AP now has the latest software image and is ready for service.

nano3GAP Installation Manual Troubleshooting

6 Troubleshooting

6.1 Internet Connection Problems

If static IP addressing is disabled and DHCP is in use, the nano3GAP-4 expects to be

automatically provided with an IP address by the broadband router every time it starts.

Ensure that the DHCP service is enabled on the broadband router.

6.2 LED Status Indicators

The following table shows the meaning of the state LED under normal and fault conditions.

Off The nano3GAP-4 is not switched on.

Green The nano3GAP-4 is powered up normally.

Flashing green Self-test is running.

Power

Red There is a fault with the nano3GAP-4.

Note: At power-up, this LED will light solid red by default.

Off Unable to detect a network. This is usually because there is no

network cable connected, or there is no network connection at the

other end of the cable (for example, the router or broadband modem

may have failed or may not be switched on).

Green The 100Mbps connection is OK.

Flashing green Indicates activity on the network at 100Mbps speed (that is, the

nano3GAP-4 is sending and/or receiving data across the LAN).

Amber The 10Mbps connection is OK.

Flashing amber Indicates activity on the network at 10Mbps speed (that is, the

nano3GAP-4 is sending and/or receiving data across the LAN).

Network

Note: This LED is driven by Ethernet hardware.

Off The nano3GAP-4 is not provisioned, it has no IP address. This may

be a temporary condition when you switch on the AP for the first

time, or after you have performed a factory reset.

Green The nano3GAP-4 is provisioned and unlocked.

Flashing green (slow) The nano3GAP-4 is provisioned and locked.

Service

Flashing green (fast) Software download is in progress to the nano3GAP-4.

nano3GAP Installation Manual Troubleshooting

6.3 Factory Reset

Factory reset can help in case the AP does not connect. The AP configuration will need to

be redone manually, see section 4.2.

To perform factory reset, press the factory reset button and hold it for more than 10

seconds.

When the button is initially pressed, the LED will blink fast (50ms on:50ms off) for 5

seconds, then it will start to blink slowly (200ms on: 200ms off). When the factory restore

process has completed, the LED will extinguish and the AP will automatically reboot, take

the fixed IP address and enable the web interface for configuration (see section 4).

nano3GAP Installation Manual nano3GAP and PSU Regulatory Information

7 nano3GAP and PSU Regulatory Information

This chapter provides the customer with safety and regulatory warnings, cautions and

information for the ip.access Ltd range of products.

7.1 Warnings and Cautions

Electrical Safety

CAUTION

The nano3GAP-4 is intended for dry indoor applications only. If evidence of

condensation is present do not apply power to the nano3GAP-4.

WARNING

Do not immerse any part of the nano3GAP-4 or its power supply in water or any

other liquid. Do not install or use the nano3GAP-4 or its power supply near open

water. Do not spill liquids of any type on the nano3GAP-4 or its power supply.

WARNING

Do not use liquid, solvent or aerosol cleaning agents on or near the nano3GAP-

4 or its power supply.

CAUTION

To avoid the risk of fire and/or electrical shock, do not push objects through

openings into the nano3GAP-4 or its power supply (except when operating the

Reset switch on the nano3GAP-4).

CAUTION

Do not disassemble the nano3GAP-4 or its power supply.

CAUTION

The nano3GAP-4 must only be powered using the ip.access power supply

provided for use with the nano3GAP-4.

CAUTION

Before using the power supply, verify that the mains voltage is within the range

specified by the voltage printed on the power supply.

CAUTION

The PSU supplied with the nano3GAP-4 must not be used for powering any

other equipment.

CAUTION

To avoid the risk of fire and/or electrical shock, do not overload power outlets or

extension cables.

CAUTION

When disconnecting the power supply from the mains, pull the plug. Pulling the

cable may result in damage to the cable.

nano3GAP Installation Manual nano3GAP and PSU Regulatory Information

Interference with Electronic Devices

CAUTION

If using a pacemaker, ensure you are using the device in accordance with its

safety requirements with respect to RF devices. Consult your doctor if you have

questions about RF signals and your pacemaker.

CAUTION

If using a hearing aid, RF devices may cause interference.

CAUTION

Unshielded electronic devices should not be used near the nano3GAP-4.

Conversely, the nano3GAP-4 should not be installed adjacent to unshielded

electrical or electronic devices (such as unshielded speakers).

Other Warnings and Cautions

WARNING

Do not install the nano3GAP-4 in a position where the power supply cable or

network cable may cause a tripping or choking hazard.

WARNING

Do not install the nano3GAP-4 or the power supply on an unstable surface. All

caution must be observed to prevent the device from falling and causing injury

to a person and/or damage to the device.

WARNING

The nano3GAP-4 should not be disposed of in household waste bins. Please

follow local regulations for disposal of electronic devices.

CAUTION

Do not install the nano3GAP-4 in a position where the power supply cable or

network cable may be damaged by walking on the cables.

CAUTION

Do not attempt to fit an external antenna or antenna cabling to the nano3GAP-4.

7.2 Regulatory Statements

7.2.1 Type Approval and EMC Standards

• FCC CFR47 Parts 15B, 27

Note: Changes or modifications not expressly approved by the party responsible for compliance

may void the user's authority to operate this equipment.

Model nano3G 219C has FCC ID QGGIPA219C

nano3GAP Installation Manual nano3GAP and PSU Regulatory Information

WARNING

This is a class B product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

Federal Communications Commission

Note: This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

7.2.2 Safety Standards

• IEC 60950-1:2005 (2nd Edition) and EN 60950-1:2006

The power adapter, as well as the POE inserter and splitter supplied by ip.access comply

with LPS requirements in accordance with IEC/EN 60950-1.

nano3GAP Installation Manual Appendices

8 Appendices

8.1 Appendix A - Example AP Configuration File

A configuration file with the object name and the objects instance (relative distinguished

name) must be created for each AP to be commissioned. For instructions to use the

configuration file, see section 5.3.

The file has to conform to the following syntax:

• all non-comment lines are of the form <name>=<value>

• comment lines begin with the hash character (#)

• attribute types are as follows:

o integer tos=0

o enumeration t300=T300_4000_MSEC

o array ascPersistenceScalingFactors=[6,6,6,6,6,6]

o boolean soipHeartbeatEnabled=true

o structure cellBroadcastMessage={50,GSM_DEFAULT,”oyster 3G”}

o string “HMAC-SHA1”

o set alarmFilter=()

# Instance for the AP to be modified

Object=apNano_001

ObjectInstance=ROOT#0;AC_CONNECTION#12007;RNS#0;AP_CONTROLLER#

0;AP_CONNECTION#31;AP#0

# Cell Package

rncIdentity=139

# NAS Package

mcc="159"

mnc="12"

sac=1

saiLac=1

# Network Listen Control Package

lacRacCandidateList=({15912,(99)})

rfParamsCandidateList=({1062,437,1})

rssiScanBands=({BAND_NAME_UMTS_BAND_04_NO_SPOT,()})

# end of file

Parameter Description

Object ID of the AP

nano3GAP Installation Manual Appendices

ObjectInstance Relative Distinguished Name

rncIdentity ID of the AC

Mcc Mobile Country Code

Mnc Mobile Network Code

Sac Service Access Code

saiLac SAC Location Area Code

lacRacCandidateList LAC and RAC list

rfParamsCandidateList Radio Frequency parameter list

rssiScanBands Scanning frequency bands for received signal strength

indication

8.2 Appendix B - Licenses and Copyright Notices

Portions of the AP are constructed from third-party software and open source code and

ip.access ltd gratefully acknowledges the contributions that these libraries, technologies

and components have made to the product. Each of these is supplied under the terms of a

license agreement and these are either reproduced or referenced below in line with the

stipulations of their authors.

8.2.1 asn1c

asn1c by Lev Walkin (vlm@lionet.info) is covered by a BSD-type license:

See the file "COPYING" in the source package

8.2.2 bash

bash by GNU is covered by the GNU GPL Version 2, as reproduced in section 8.2.28.1.

8.2.3 BusyBox

BusyBox by BusyBox.net is covered by the GNU GPL Version 2, as reproduced in section

8.2.28.1.

8.2.4 cramfs

cramfs by SourceForge(cramfs) is covered by the GNU GPL Version 2, as reproduced in

section 8.2.28.1.

nano3GAP Installation Manual Appendices

8.2.5 dropbear

dropbear by Matt Johnston (http://matt.ucc.asn.au/dropbear/dropbear.html) is covered by

various MIT-type licenses.

See the file "LICENSE" in the source package.

8.2.6 glibc

glibc by Code Sourcery is covered by LGPL v2.1, as reproduced in section 8.2.28.2.

8.2.7 gmp

gmp by GNU is covered by LGPL v2.1, as reproduced in section 8.2.28.2.

8.2.8 ipkg

ipkg by Handhelds.org is covered by the GNU GPL Version 2, as reproduced in section

8.2.28.1.

8.2.9 iproute2

iproute2 by The Linux Foundation (osdl.org) is covered by the GNU GPL Version 2, as

reproduced in section 8.2.28.1.

8.2.10 iptables

iptables by Netfilrter is covered by GNU GPL Version 2, as reproduced in section 8.2.28.1.

8.2.11 libcurl

libcurl by cURL is covered by an MIT-type license:

Permission to use, copy, modify, and distribute this software for any purpose with or

without fee is hereby granted, provided that the above copyright notice and this permission

notice appear in all copies.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO EVENT SHALL THE

AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR

OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE,

ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE

OR OTHER DEALINGS IN THE SOFTWARE.

Except as contained in this notice, the name of a copyright holder shall not be used in

advertising or otherwise to promote the sale, use or other dealings in this Software without

prior written authorization of the copyright holder.

nano3GAP Installation Manual Appendices

8.2.12 libgcc

libgcc by Code Sourcery is covered by GPL v2 with “run-time exception”:

See the gcc/libgcc2.c header in the source package.

8.2.13 libpcap

libpcap by tcpdump.org is covered by an BSD-type license.

See the file "LICENSE" in the source package.

8.2.14 libxml2

libxml by xmlsoft.org is covered by the MIT license:

The MIT License

Permission is hereby granted, free of charge, to any person obtaining a copy of this

software and associated documentation files (the "Software"), to deal in the Software

without restriction, including without limitation the rights to use, copy, modify, merge,

publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to

whom the Software is furnished to do so, subject to the following conditions:

The above copyright notice and this permission notice shall be included in all copies or

substantial portions of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,

EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF

MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT

SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT

OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE

SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

8.2.15 Linux Kernel

The Linux Kernel by kernel.org is covered by the GNU GPL Version 2, as reproduced in

section 8.2.28.1.

8.2.16 mtd.utils

mtd.utils by MTD (http://www.linux-mtd.infradead.org/index.html) is covered by the GNU

GPL Version 2, as reproduced in section 8.2.28.1.

nano3GAP Installation Manual Appendices

8.2.17 ncurses

ncurses by GNU is covered by an MIT-type license.

See the header of the file "curses.h.in" in the source package.

8.2.18 NTP daemon

NTP daemon by NTP.org is covered by the NTP.org license.

Permission to use, copy, modify, and distribute this software and its documentation for any

purpose with or without fee is hereby granted, provided that the above copyright notice

appears in all copies and that both the copyright notice and this permission notice appear

in supporting documentation, and that the name University of Delaware not be used in

advertising or publicity pertaining to distribution of the software without specific, written

prior permission. The University of Delaware makes no representations about the

suitability this software for any purpose. It is provided "as is" without express or implied

warranty.

8.2.19 pcre

pcre by pcre.org is covered by a BSD-type license.

PCRE LICENCE

------------

PCRE is a library of functions to support regular expressions whose syntaxand semantics

are as close as possible to those of the Perl 5 language.

Release 7 of PCRE is distributed under the terms of the "BSD" licence, asspecified below.

The documentation for PCRE, supplied in the "doc" directory, is distributed under the same

terms as the software itself.

The basic library functions are written in C and are freestanding. Also included in the

distribution is a set of C++ wrapper functions.

THE BASIC LIBRARY FUNCTIONS

---------------------------

Written by: Philip Hazel

Email local part: ph10

Email domain: cam.ac.uk

University of Cambridge Computing Service,

Cambridge, England.

nano3GAP Installation Manual Appendices

THE C++ WRAPPER FUNCTIONS

-------------------------

Contributed by: Google Inc.

THE "BSD" LICENCE

-----------------

Redistribution and use in source and binary forms, with or without modification, are

permitted provided that the following conditions are met:

* Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

* Redistributions in binary form must reproduce the above copyright notice, this list of

conditions and the following disclaimer in the documentation and/or other materials

provided with the distribution.

* Neither the name of the University of Cambridge nor the name of Google Inc. nor the

names of their contributors may be used to endorse or promote products derived from this

software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND

CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS

BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT

OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR

BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

End

nano3GAP Installation Manual Appendices

8.2.20 procps

procps by SourceForge(procps) is covered by the GPL v2 and LGPL v2 licenses as

reproduced in section 8.2.28.1 and in section 8.2.28.2, respectively.

8.2.21 SSL Stack

SSL Stack by openssl.org is covered by the OpenSSL license, as reproduced in section

8.2.28.3.

8.2.22 StrongSwan

StrongSwan by StrongSwan.org is covered mainly by GNU GPL Version 2.as reproduced

in section 8.2.28.1. Some code is covered by the OpenSSL license (see section 8.2.28.3),

and some under a BSD-type license.

StrongSwan license

Except for the DES library, MD2 and MD5 code, the PKCS#11 headers, and the

FIPS_canister code this software is under the GNU Public License, see the file COPYING.

See the file CREDITS for details on origins of more of the code.

The DES library is under a BSD style license, see src/libcrypto/libdes/COPYRIGHT. Note

that this software has a advertising clause in it.

The MD2 implementation is from RSA Data Security Inc., so this package must include the

following phrase: "RSA Data Security, Inc. MD2 Message Digest Algorithm" It is not under

the GPL; see details in src/pluto/md2.c.

The MD5 implementation is from RSA Data Security Inc., so this package must include the

following phrase: "derived from the RSA Data Security, Inc. MD5 Message-Digest

Algorithm". It is not under the GPL; see details in src/pluto/md5.c

The PKCS#11 header files in src/pluto/rsaref/ are from RSA Security Inc., so they must

include the following phrase: "RSA Security Inc. PKCS#11 Cryptographic Token Interface

(Cryptoki)". The headers are not under the GPL; see details in src/pluto/rsaref/pkcs11.h.

In addition to the terms set out under the GPL, permission is granted to link the software

against the libdes, MD2, and MD5 libraries just mentioned.

8.2.23 TCL

TCL by SoundForge(tcl) is covered by a BSD-type license:

This software is copyrighted by the Regents of the University of California, Sun

Microsystems, Inc., Scriptics Corporation, and other parties. The following terms apply to

all files associated with the software unless explicitly disclaimed in individual files.

The authors hereby grant permission to use, copy, modify, distribute, and license this

software and its documentation for any purpose, provided that existing copyright notices

nano3GAP Installation Manual Appendices

are retained in all copies and that this notice is included verbatim in any distributions. No

written agreement, license, or royalty fee is required for any of the authorized uses.

Modifications to this software may be copyrighted by their authors and need not follow the

licensing terms described here, provided that the new terms are clearly indicated on the

first page of each file where they apply.

IN NO EVENT SHALL THE AUTHORS OR DISTRIBUTORS BE LIABLE TO ANY PARTY

FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES

ARISING OUT OF THE USE OF THIS SOFTWARE, ITS DOCUMENTATION, OR ANY

DERIVATIVES THEREOF, EVEN IF THE AUTHORS HAVE BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGE.

THE AUTHORS AND DISTRIBUTORS SPECIFICALLY DISCLAIM ANY WARRANTIES,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-

INFRINGEMENT. THIS SOFTWARE IS PROVIDED ON AN "AS IS" BASIS, AND THE

AUTHORS AND DISTRIBUTORS HAVE NO OBLIGATION TO PROVIDE

MAINTENANCE, SUPPORT, UPDATES, ENHANCEMENTS, OR MODIFICATIONS.

GOVERNMENT USE: If you are acquiring this software on behalf of the U.S. government,

the Government shall have only "Restricted Rights" in the software and related

documentation as defined in the Federal Acquisition Regulations (FARs) in Clause

52.227.19 (c) (2). If you are acquiring the software on behalf of the Department of

Defense, the software shall be classified as "Commercial Computer Software" and the

Government shall have only "Restricted Rights" as defined in Clause 252.227-7013 (c) (1)

of DFARs. Notwithstanding the foregoing, the authors grant the U.S. Government and

others acting in its behalf permission to use and distribute the software in accordance with

the terms specified in this license.

8.2.24 tcpdump

tcpdump by tcpdump.org is covered by a BSD-type license.

See the file "LICENSE" in the source package.

8.2.25 thttpd

thttpd by ACME Laboratories is covered by a BSD-type license.

See the header of the file "thttpd.c" in the source package.

8.2.26 U-Boot

U-Boot by DENX is covered by GNU GPL Version 2, as reproduced in section 8.2.28.1.

8.2.27 zlib

zlib by zlib.net is covered by the zlip license:.

8.2.28 General Licenses

The licenses reproduced here are referenced by more than one product, as in the

preceding sections.

nano3GAP Installation Manual Appendices

8.2.28.1 GNU GPL Version 2

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of this license document, but

changing it is not allowed.

Preamble

The licenses for most software are designed to take away your freedom to share and

change it. By contrast, the GNU General Public License is intended to guarantee your

freedom to share and change free software--to make sure the software is free for all its

users. This General Public License applies to most of the Free Software Foundation's

software and to any other program whose authors commit to using it. (Some other Free

Software Foundation software is covered by the GNU Lesser General Public License

instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not price. Our General

Public Licenses are designed to make sure that you have the freedom to distribute copies

of free software (and charge for this service if you wish), that you receive source code or

can get it if you want it, that you can change the software or use pieces of it in new free

programs; and that you know you can do these things.

To protect your rights, we need to make restrictions that forbid anyone to deny you these

rights or to ask you to surrender the rights. These restrictions translate to certain

responsibilities for you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether gratis or for a fee, you

must give the recipients all the rights that you have. You must make sure that they, too,

receive or can get the source code. And you must show them these terms so they know

their rights.

We protect your rights with two steps: (1) copyright the software, and (2) offer you this

license which gives you legal permission to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make certain that everyone

understands that there is no warranty for this free software. If the software is modified by

someone else and passed on, we want its recipients to know that what they have is not the

original, so that any problems introduced by others will not reflect on the original authors'

reputations.

Finally, any free program is threatened constantly by software patents. We wish to avoid

the danger that redistributors of a free program will individually obtain patent licenses, in

effect making the program proprietary. To prevent this, we have made it clear that any

patent must be licensed for everyone's free use or not licensed at all.

The precise terms and conditions for copying, distribution and modification follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

nano3GAP Installation Manual Appendices

0. This License applies to any program or other work which contains a notice placed by the

License. The "Program", below, refers to any such program or work, and a "work based

on the Program" means either the Program or any derivative work under copyright law:

that is to say, a work containing the Program or a portion of it, either verbatim or with

modifications and/or translated into another language. (Hereinafter, translation is included

without limitation in the term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification are not covered by this License;

they are outside its scope. The act of running the Program is not restricted, and the output

from the Program is covered only if its contents constitute a work based on the Program

(independent of having been made by running the Program). Whether that is true depends

on what the Program does.

1. You may copy and distribute verbatim copies of the Program's source code as you

receive it, in any medium, provided that you conspicuously and appropriately publish on

each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the

notices that refer to this License and to the absence of any warranty; and give any other

recipients of the Program a copy of this License along with the Program.

You may charge a fee for the physical act of transferring a copy, and you may at your

option offer warranty protection in exchange for a fee.

2. You may modify your copy or copies of the Program or any portion of it, thus forming a

work based on the Program, and copy and distribute such modifications or work under the

terms of Section 1 above, provided that you also meet all of these conditions:

a) You must cause the modified files to carry prominent notices stating that you

changed the files and the date of any change.

b) You must cause any work that you distribute or publish, that in whole or in part

contains or is derived from the Program or any part thereof, to be licensed as a

whole at no charge to all third parties under the terms of this License.

c) If the modified program normally reads commands interactively when run, you

must cause it, when started running for such interactive use in the most ordinary

way, to print or display an announcement including an appropriate copyright

notice and a notice that there is no warranty (or else, saying that you provide a

warranty) and that users may redistribute the program under these conditions,

and telling the user how to view a copy of this License. (Exception: if the Program

itself is interactive but does not normally print such an announcement, your work

based on the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If identifiable sections of that

work are not derived from the Program, and can be reasonably considered independent

and separate works in themselves, then this License, and its terms, do not apply to those

sections when you distribute them as separate works. But when you distribute the same

sections as part of a whole which is a work based on the Program, the distribution of the

whole must be on the terms of this License, whose permissions for other licensees extend

to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work written

entirely by you; rather, the intent is to exercise the right to control the distribution of

derivative or collective works based on the Program.

nano3GAP Installation Manual Appendices

In addition, mere aggregation of another work not based on the Program with the Program

(or with a work based on the Program) on a volume of a storage or distribution medium

does not bring the other work under the scope of this License.

3. You may copy and distribute the Program (or a work based on it, under Section 2) in

object code or executable form under the terms of Sections 1 and 2 above provided that

you also do one of the following:

a) Accompany it with the complete corresponding machine-readable source code,

which must be distributed under the terms of Sections 1 and 2 above on a

medium customarily used for software interchange; or,

b) Accompany it with a written offer, valid for at least three years, to give any third

party, for a charge no more than your cost of physically performing source

distribution, a complete machine-readable copy of the corresponding source

code, to be distributed under the terms of Sections 1 and 2 above on a medium

customarily used for software interchange; or,

c) Accompany it with the information you received as to the offer to distribute

corresponding source code. (This alternative is allowed only for noncommercial

distribution and only if you received the program in object code or executable form

with such an offer, in accord with Subsection b above.)

The source code for a work means the preferred form of the work for making modifications

to it. For an executable work, complete source code means all the source code for all

modules it contains, plus any associated interface definition files, plus the scripts used to

control compilation and installation of the executable. However, as a special exception,

the source code distributed need not include anything that is normally distributed (in either

source or binary form) with the major components (compiler, kernel, and so on) of the

operating system on which the executable runs, unless that component itself accompanies

the executable.

If distribution of executable or object code is made by offering access to copy from a

designated place, then offering equivalent access to copy the source code from the same

place counts as distribution of the source code, even though third parties are not

compelled to copy the source along with the object code.

4. You may not copy, modify, sublicense, or distribute the Program except as expressly

provided under this License. Any attempt otherwise to copy, modify, sublicense or

distribute the Program is void, and will automatically terminate your rights under this

License. However, parties who have received copies, or rights, from you under this

License will not have their licenses terminated so long as such parties remain in full

compliance.

5. You are not required to accept this License, since you have not signed it. However,

nothing else grants you permission to modify or distribute the Program or its derivative

works. These actions are prohibited by law if you do not accept this License. Therefore,

by modifying or distributing the Program (or any work based on the Program), you indicate

your acceptance of this License to do so, and all its terms and conditions for copying,

distributing or modifying the Program or works based on it.

6. Each time you redistribute the Program (or any work based on the Program), the

recipient automatically receives a license from the original licensor to copy, distribute or

modify the Program subject to these terms and conditions. You may not impose any

nano3GAP Installation Manual Appendices

further restrictions on the recipients' exercise of the rights granted herein. You are not

responsible for enforcing compliance by third parties to this License.

7. If, as a consequence of a court judgment or allegation of patent infringement or for any

other reason (not limited to patent issues), conditions are imposed on you (whether by

court order, agreement or otherwise) that contradict the conditions of this License, they do

not excuse you from the conditions of this License. If you cannot distribute so as to satisfy

simultaneously your obligations under this License and any other pertinent obligations,

then as a consequence you may not distribute the Program at all. For example, if a patent

license would not permit royalty-free redistribution of the Program by all those who receive

copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Program.

If any portion of this section is held invalid or unenforceable under any particular

circumstance, the balance of the section is intended to apply and the section as a whole is

intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property

right claims or to contest validity of any such claims; this section has the sole purpose of

protecting the integrity of the free software distribution system, which is implemented by

public license practices. Many people have made generous contributions to the wide

range of software distributed through that system in reliance on consistent application of

that system; it is up to the author/donor to decide if he or she is willing to distribute

software through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of

the rest of this License.

8. If the distribution and/or use of the Program is restricted in certain countries either by

patents or by copyrighted interfaces, the original copyright holder who places the Program

under this License may add an explicit geographical distribution limitation excluding those

countries, so that distribution is permitted only in or among countries not thus excluded. In

such case, this License incorporates the limitation as if written in the body of this License.

9. The Free Software Foundation may publish revised and/or new versions of the General

Public License from time to time. Such new versions will be similar in spirit to the present

version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Program specifies a version

number of this License which applies to it and "any later version", you have the option of

following the terms and conditions either of that version or of any later version published by

the Free Software Foundation. If the Program does not specify a version number of this

License, you may choose any version ever published by the Free Software Foundation.

10. If you wish to incorporate parts of the Program into other free programs whose

distribution conditions are different, write to the author to ask for permission. For software

which is copyrighted by the Free Software Foundation, write to the Free Software

Foundation; we sometimes make exceptions for this. Our decision will be guided by the

two goals of preserving the free status of all derivatives of our free software and of

promoting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO

WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE

nano3GAP Installation Manual Appendices

LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT

HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE

DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR

CORRECTION.

12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN

WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY

MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE

LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE

THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING

RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR

A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN

IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

END OF TERMS AND CONDITIONS

8.2.28.2 GNU LGPL v2.1

GNU Lesser General Public License

Version 2.1, February 1999

Boston, MA 02111-1307 USA Everyone is permitted to copy and distribute verbatim copies

of this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also counts as the successor of

the GNU Library Public License, version 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your freedom to share and

change it. By contrast, the GNU General Public Licenses are intended to guarantee your

freedom to share and change free software--to make sure the software is free for all its

users.

This license, the Lesser General Public License, applies to some specially designated

software packages--typically libraries--of the Free Software Foundation and other authors

who decide to use it. You can use it too, but we suggest you first think carefully about

whether this license or the ordinary General Public License is the better strategy to use in

any particular case, based on the explanations below.

When we speak of free software, we are referring to freedom of use, not price. Our

General Public Licenses are designed to make sure that you have the freedom to

distribute copies of free software (and charge for this service if you wish); that you receive

nano3GAP Installation Manual Appendices

source code or can get it if you want it; that you can change the software and use pieces of

it in new free programs; and that you are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid distributors to deny you

these rights or to ask you to surrender these rights. These restrictions translate to certain

responsibilities for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis or for a fee, you must

give the recipients all the rights that we gave you. You must make sure that they, too,

receive or can get the source code. If you link other code with the library, you must provide

complete object files to the recipients, so that they can relink them with the library after

making changes to the library and recompiling it. And you must show them these terms so

they know their rights.

We protect your rights with a two-step method: (1) we copyright the library, and (2) we

offer you this license, which gives you legal permission to copy, distribute and/or modify

the library.

To protect each distributor, we want to make it very clear that there is no warranty for the

free library. Also, if the library is modified by someone else and passed on, the recipients

should know that what they have is not the original version, so that the original author's

reputation will not be affected by problems that might be introduced by others.

Finally, software patents pose a constant threat to the existence of any free program. We

wish to make sure that a company cannot effectively restrict the users of a free program by

obtaining a restrictive license from a patent holder. Therefore, we insist that any patent

license obtained for a version of the library must be consistent with the full freedom of use

specified in this license.

Most GNU software, including some libraries, is covered by the ordinary GNU General

Public License. This license, the GNU Lesser General Public License, applies to certain

designated libraries, and is quite different from the ordinary General Public License. We

use this license for certain libraries in order to permit linking those libraries into non-free

programs.

When a program is linked with a library, whether statically or using a shared library, the

combination of the two is legally speaking a combined work, a derivative of the original

library. The ordinary General Public License therefore permits such linking only if the entire

combination fits its criteria of freedom. The Lesser General Public License permits more

lax criteria for linking other code with the library.

We call this license the "Lesser" General Public License because it does Less to protect

the user's freedom than the ordinary General Public License. It also provides other free

software developers Less of an advantage over competing non-free programs. These

disadvantages are the reason we use the ordinary General Public License for many

libraries. However, the Lesser license provides advantages in certain special

circumstances.

For example, on rare occasions, there may be a special need to encourage the widest

possible use of a certain library, so that it becomes a de-facto standard. To achieve this,

non-free programs must be allowed to use the library. A more frequent case is that a free

library does the same job as widely used non-free libraries. In this case, there is little to

gain by limiting the free library to free software only, so we use the Lesser General Public

License.

nano3GAP Installation Manual Appendices

In other cases, permission to use a particular library in non-free programs enables a

greater number of people to use a large body of free software. For example, permission to

use the GNU C Library in non-free programs enables many more people to use the whole

GNU operating system, as well as its variant, the GNU/Linux operating system.

Although the Lesser General Public License is Less protective of the users' freedom, it

does ensure that the user of a program that is linked with the Library has the freedom and

the wherewithal to run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and modification follow. Pay

close attention to the difference between a "work based on the library" and a "work that

uses the library". The former contains code derived from the library, whereas the latter

must be combined with the library in order to run.

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION

0. This License Agreement applies to any software library or other program which contains

a notice placed by the copyright holder or other authorized party saying it may be

distributed under the terms of this Lesser General Public License (also called "this

License"). Each licensee is addressed as "you".

A "library" means a collection of software functions and/or data prepared so as to be

conveniently linked with application programs (which use some of those functions and

data) to form executables.

The "Library", below, refers to any such software library or work which has been distributed

under these terms. A "work based on the Library" means either the Library or any

derivative work under copyright law: that is to say, a work containing the Library or a

portion of it, either verbatim or with modifications and/or translated straightforwardly into

another language. (Hereinafter, translation is included without limitation in the term

"modification".)

"Source code" for a work means the preferred form of the work for making modifications to

it. For a library, complete source code means all the source code for all modules it

contains, plus any associated interface definition files, plus the scripts used to control

compilation and installation of the library.

Activities other than copying, distribution and modification are not covered by this License;

they are outside its scope. The act of running a program using the Library is not restricted,

and output from such a program is covered only if its contents constitute a work based on

the Library (independent of the use of the Library in a tool for writing it). Whether that is

true depends on what the Library does and what the program that uses the Library does.

1. You may copy and distribute verbatim copies of the Library's complete source code as

you receive it, in any medium, provided that you conspicuously and appropriately publish

on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all

the notices that refer to this License and to the absence of any warranty; and distribute a

copy of this License along with the Library.

You may charge a fee for the physical act of transferring a copy, and you may at your

option offer warranty protection in exchange for a fee.

nano3GAP Installation Manual Appendices

2. You may modify your copy or copies of the Library or any portion of it, thus forming a

work based on the Library, and copy and distribute such modifications or work under the

terms of Section 1 above, provided that you also meet all of these conditions:

a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent notices stating that you changed

the files and the date of any change.

c) You must cause the whole of the work to be licensed at no charge to all third parties

under the terms of this License.

d) If a facility in the modified Library refers to a function or a table of data to be supplied

by an application program that uses the facility, other than as an argument passed when

the facility is invoked, then you must make a good faith effort to ensure that, in the event

an application does not supply such function or table, the facility still operates, and

performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots has a purpose that is

entirely well-defined independent of the application. Therefore, Subsection 2d requires that

any application-supplied function or table used by this function must be optional: if the

application does not supply it, the square root function must still compute square roots.)

These requirements apply to the modified work as a whole. If identifiable sections of that

work are not derived from the Library, and can be reasonably considered independent and

separate works in themselves, then this License, and its terms, do not apply to those

sections when you distribute them as separate works. But when you distribute the same

sections as part of a whole which is a work based on the Library, the distribution of the

whole must be on the terms of this License, whose permissions for other licensees extend

to the entire whole, and thus to each and every part regardless of who wrote it.

Thus, it is not the intent of this section to claim rights or contest your rights to work

written entirely by you; rather, the intent is to exercise the right to control the distribution of

derivative or collective works based on the Library.

In addition, mere aggregation of another work not based on the Library with the Library

(or with a work based on the Library) on a volume of a storage or distribution medium does

not bring the other work under the scope of this License.

3. You may opt to apply the terms of the ordinary GNU General Public License instead of

this License to a given copy of the Library. To do this, you must alter all the notices that

refer to this License, so that they refer to the ordinary GNU General Public License,

version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU

General Public License has appeared, then you can specify that version instead if you

wish.) Do not make any other change in these notices.

Once this change is made in a given copy, it is irreversible for that copy, so the ordinary

GNU General Public License applies to all subsequent copies and derivative works made

from that copy.

This option is useful when you wish to copy part of the code of the Library into a program

that is not a library.

nano3GAP Installation Manual Appendices

4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2)

in object code or executable form under the terms of Sections 1 and 2 above provided that

you accompany it with the complete corresponding machine-readable source code, which

must be distributed under the terms of Sections 1 and 2 above on a medium customarily

used for software interchange.

If distribution of object code is made by offering access to copy from a designated place,

then offering equivalent access to copy the source code from the same place satisfies the

requirement to distribute the source code, even though third parties are not compelled to

copy the source along with the object code.

5. A program that contains no derivative of any portion of the Library, but is designed to

work with the Library by being compiled or linked with it, is called a "work that uses the

Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls

outside the scope of this License.

However, linking a "work that uses the Library" with the Library creates an executable that

is a derivative of the Library (because it contains portions of the Library), rather than a

"work that uses the library". The executable is therefore covered by this License. Section 6

states terms for distribution of such executables.

When a "work that uses the Library" uses material from a header file that is part of the

Library, the object code for the work may be a derivative work of the Library even though

the source code is not. Whether this is true is especially significant if the work can be

linked without the Library, or if the work is itself a library. The threshold for this to be true is

not precisely defined by law.

If such an object file uses only numerical parameters, data structure layouts and

accessors, and small macros and small inline functions (ten lines or less in length), then

the use of the object file is unrestricted, regardless of whether it is legally a derivative work.

(Executables containing this object code plus portions of the Library will still fall under

Section 6.)

Otherwise, if the work is a derivative of the Library, you may distribute the object code for

the work under the terms of Section 6. Any executables containing that work also fall under

Section 6, whether or not they are linked directly with the Library itself.

6. As an exception to the Sections above, you may also combine or link a "work that uses

the Library" with the Library to produce a work containing portions of the Library, and

distribute that work under terms of your choice, provided that the terms permit modification

of the work for the customer's own use and reverse engineering for debugging such

modifications.

You must give prominent notice with each copy of the work that the Library is used in it

and that the Library and its use are covered by this License. You must supply a copy of

this License. If the work during execution displays copyright notices, you must include the

the copy of this License. Also, you must do one of these things:

a) Accompany the work with the complete corresponding machine-readable source

code for the Library including whatever changes were used in the work (which must be

distributed under Sections 1 and 2 above); and, if the work is an executable linked with the

nano3GAP Installation Manual Appendices

Library, with the complete machine-readable "work that uses the Library", as object code

and/or source code, so that the user can modify the Library and then relink to produce a

modified executable containing the modified Library. (It is understood that the user who

changes the contents of definitions files in the Library will not necessarily be able to

recompile the application to use the modified definitions.)

b) Use a suitable shared library mechanism for linking with the Library. A suitable

mechanism is one that (1) uses at run time a copy of the library already present on the

user's computer system, rather than copying library functions into the executable, and (2)

will operate properly with a modified version of the library, if the user installs one, as long

as the modified version is interface-compatible with the version that the work was made

with.

c) Accompany the work with a written offer, valid for at least three years, to give the

same user the materials specified in Subsection 6a, above, for a charge no more than the

cost of performing this distribution.

d) If distribution of the work is made by offering access to copy from a designated place,

offer equivalent access to copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these materials or that you have

already sent this user a copy.

For an executable, the required form of the "work that uses the Library" must include any

data and utility programs needed for reproducing the executable from it. However, as a

special exception, the materials to be distributed need not include anything that is normally

distributed (in either source or binary form) with the major components (compiler, kernel,

and so on) of the operating system on which the executable runs, unless that component

itself accompanies the executable.

It may happen that this requirement contradicts the license restrictions of other proprietary

libraries that do not normally accompany the operating system. Such a contradiction

means you cannot use both them and the Library together in an executable that you

distribute.

7. You may place library facilities that are a work based on the Library side-by-side in a

single library together with other library facilities not covered by this License, and distribute

such a combined library, provided that the separate distribution of the work based on the

Library and of the other library facilities is otherwise permitted, and provided that you do

these two things:

a) Accompany the combined library with a copy of the same work based on the Library,

uncombined with any other library facilities. This must be distributed under the terms of the

Sections above.

b) Give prominent notice with the combined library of the fact that part of it is a work

based on the Library, and explaining where to find the accompanying uncombined form of

the same work.

8. You may not copy, modify, sublicense, link with, or distribute the Library except as

expressly provided under this License. Any attempt otherwise to copy, modify, sublicense,

link with, or distribute the Library is void, and will automatically terminate your rights under

nano3GAP Installation Manual Appendices

this License. However, parties who have received copies, or rights, from you under this

License will not have their licenses terminated so long as such parties remain in full

compliance.

9. You are not required to accept this License, since you have not signed it. However,

nothing else grants you permission to modify or distribute the Library or its derivative

works. These actions are prohibited by law if you do not accept this License. Therefore, by

modifying or distributing the Library (or any work based on the Library), you indicate your

acceptance of this License to do so, and all its terms and conditions for copying,

distributing or modifying the Library or works based on it.

10. Each time you redistribute the Library (or any work based on the Library), the recipient

automatically receives a license from the original licensor to copy, distribute, link with or

modify the Library subject to these terms and conditions. You may not impose any further

restrictions on the recipients' exercise of the rights granted herein. You are not responsible

for enforcing compliance by third parties with this License.

11. If, as a consequence of a court judgment or allegation of patent infringement or for any

other reason (not limited to patent issues), conditions are imposed on you (whether by

court order, agreement or otherwise) that contradict the conditions of this License, they do

not excuse you from the conditions of this License. If you cannot distribute so as to satisfy

simultaneously your obligations under this License and any other pertinent obligations,

then as a consequence you may not distribute the Library at all. For example, if a patent

license would not permit royalty-free redistribution of the Library by all those who receive

copies directly or indirectly through you, then the only way you could satisfy both it and this

License would be to refrain entirely from distribution of the Library.

If any portion of this section is held invalid or unenforceable under any particular

circumstance, the balance of the section is intended to apply, and the section as a whole is

intended to apply in other circumstances.

It is not the purpose of this section to induce you to infringe any patents or other property

right claims or to contest validity of any such claims; this section has the sole purpose of

protecting the integrity of the free software distribution system which is implemented by

public license practices. Many people have made generous contributions to the wide range

of software distributed through that system in reliance on consistent application of that

system; it is up to the author/donor to decide if he or she is willing to distribute software

through any other system and a licensee cannot impose that choice.

This section is intended to make thoroughly clear what is believed to be a consequence of

the rest of this License.

12. If the distribution and/or use of the Library is restricted in certain countries either by

patents or by copyrighted interfaces, the original copyright holder who places the Library

under this License may add an explicit geographical distribution limitation excluding those

countries, so that distribution is permitted only in or among countries not thus excluded. In

such case, this License incorporates the limitation as if written in the body of this License.

nano3GAP Installation Manual Appendices

13. The Free Software Foundation may publish revised and/or new versions of the Lesser

General Public License from time to time. Such new versions will be similar in spirit to the

present version, but may differ in detail to address new problems or concerns.

Each version is given a distinguishing version number. If the Library specifies a version

number of this License which applies to it and "any later version", you have the option of

following the terms and conditions either of that version or of any later version published by

the Free Software Foundation. If the Library does not specify a license version number,

you may choose any version ever published by the Free Software Foundation.

14. If you wish to incorporate parts of the Library into other free programs whose

distribution conditions are incompatible with these, write to the author to ask for

permission. For software which is copyrighted by the Free Software Foundation, write to

the Free Software Foundation; we sometimes make exceptions for this. Our decision will

be guided by the two goals of preserving the free status of all derivatives of our free

software and of promoting the sharing and reuse of software generally.

NO WARRANTY

15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO

WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW.

EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS

AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF

ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND

PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE

DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR

CORRECTION.

16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN

WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY

MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE

TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE

LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING

RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR

A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF

SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to Apply These Terms to Your New Libraries

If you develop a new library, and you want it to be of the greatest possible use to the

public, we recommend making it free software that everyone can redistribute and change.

nano3GAP Installation Manual Appendices

You can do so by permitting redistribution under these terms (or, alternatively, under the

terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library. It is safest to attach them

to the start of each source file to most effectively convey the exclusion of warranty; and

each file should have at least the "copyright" line and a pointer to where the full notice is

found.

<one line to give the library's name and an idea of what it does.> Copyright (C) <year>

This library is free software; you can redistribute it and/or modify it under the terms of

the GNU Lesser General Public License as published by the Free Software Foundation;

either version 2.1 of the License, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but WITHOUT ANY

WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR

A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more

details.

You should have received a copy of the GNU Lesser General Public License along with

this library; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330,

Boston, MA 02111-1307 USA

Also add information on how to contact you by electronic and paper mail.

You should also get your employer (if you work as a programmer) or your school, if any, to

sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the

names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for

tweaking knobs) written by James Random Hacker.

signature of Ty Coon, 1 April 1990

Ty Coon, President of Vice

That's all there is to it!

8.2.28.3 OpenSSL License

LICENSE ISSUES

The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL

License and the original SSLeay license apply to the toolkit. See below for the actual

license texts. Actually both licenses are BSD-style Open Source licenses. In case of any

license issues related to OpenSSL please contact openssl-core@openssl.org.

OpenSSL License

Redistribution and use in source and binary forms, with or without modification, are

permitted provided that the following conditions are met:

nano3GAP Installation Manual Appendices

1. Redistributions of source code must retain the above copyright notice, this list of

conditions and the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of

conditions and the following disclaimer in the documentation and/or other materials

provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the

following acknowledgment:

"This product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit. (http://www.openssl.org/)"

4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or

promote products derived from this software without prior written permission. For written

permission, please contact openssl-core@openssl.org.

* 5. Products derived from this software may not be called "OpenSSL" nor may

"OpenSSL" appear in their names without prior written permission of the OpenSSL Project.

* 6. Redistributions of any form whatsoever must retain the following acknowledgment:

"This product includes software developed by the OpenSSL Project for use in the

OpenSSL Toolkit (http://www.openssl.org/)"

THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY

EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS

CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,

EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,

PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR

PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY

THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE

USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

====================================================================

This product includes cryptographic software written by Eric Young (eay@cryptsoft.com).

This product includes software written by Tim Hudson (tjh@cryptsoft.com).

Original SSLeay License

This package is an SSL implementation written by Eric Young (eay@cryptsoft.com).

The implementation was written so as to conform with Netscapes SSL.

This library is free for commercial and non-commercial use as long as the following

conditions are aheared to. The following conditions apply to all code found in this

distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL

documentation included with this distribution is covered by the same copyright terms

except that the holder is Tim Hudson (tjh@cryptsoft.com).

nano3GAP Installation Manual Appendices

be removed.

If this package is used in a product, Eric Young should be given attribution as the author of

the parts of the library used.

This can be in the form of a textual message at program startup or in documentation

(online or textual) provided with the package.

Redistribution and use in source and binary forms, with or without modification, are

permitted provided that the following conditions are met:

1. Redistributions of source code must retain the copyright notice, this list of conditions and

the following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of

conditions and the following disclaimer in the documentation and/or other materials

provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the

following acknowledgement:

"This product includes cryptographic software written by Eric Young

(eay@cryptsoft.com)"

The word 'cryptographic' can be left out if the rouines from the library being used are not

cryptographic related :-).

4. If you include any Windows specific code (or a derivative thereof) from the apps

directory (application code) you must include an acknowledgement:

"This product includes software written by Tim Hudson (tjh@cryptsoft.com)"

THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS'' AND ANY EXPRESS OR

IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE

LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR

CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT

OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR

BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF

LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING

NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS

SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

The licence and distribution terms for any publically available version or derivative of this

code cannot be changed. i.e. this code cannot simply be copied and put under another

distribution licence [including the GNU Public Licence.]

ip access IPA219C 3G Picocellular basestation User Manual nano3GAP Installation Manual

ip.access ltd 3G Picocellular basestation nano3GAP Installation Manual

Contents

Installation guide

Navigation menu

Namespaces

Views

Navigation