About Telewave. Telewave, Inc. designs and manufactures rugged, high-quality wireless system equipment for domestic and international markets. We support conventional and trunked radio...
TELEWAVE, INC. CATALOG 31 About Telewave Telewave, Inc. designs and manufactures rugged, high-quality wireless system equipment for domestic and international markets. We support conventional and trunked radio systems, as well as Cellular, SMR, PCS, Trunking, Paging, and Broadcast services. Our customers include public safety providers, local and state governments, federal agencies, wireless system operators, and businesses, Since 1972, Telewave has focused on the needs of our customers, providing the best American-made wireless system products, with the fastest on-time delivery record in the industry. As pioneers of lowloss combining, Telewave's early reputation as a premier problem solver was made by reorganizing and "cleaning up" some of the most crowded and complex radio transmitter sites in the San Francisco Bay Area. Where off-the-shelf products for interference control often did not exist, Telewave built custom high performance equipment to meet customer requirements. These innovative designs became the foundation of our early product line. Many equipment manufacturers will not accommodate custom orders or special requirements. Telewave has the engineering expertise and manufacturing flexibility that allows us to quickly modify existing equipment, or design a completely new product line to meet any performance goal. Initial evaluation and consultation have always been provided to customers at no charge. Telewave products are supported by a full network of US and international sales engineers, representatives, and distributors. Telewave is certified to meet the requirements of ISO 9001:2008, and our commitment to high quality and excellent customer service continues to guide our efforts. Telewave Sales and Distribution 1-800-331-3396 660 Giguere Court · San Jose, CA 95133 (408) 929-4400 · (408) 929-4080 fax www.telewave.com · sales@telewave.com Distributors - USA and Canada Talley Communications Santa Fe Springs, CA 90670 1-800-949-7079 (562) 906-8000 (562) 906-8080 fax www.talleycom.com sales@talleycom.com Tessco Technologies, Inc. Hunt Valley, MD 21031 1-800-508-5444 (410) 229-1200 (410) 527-0005 fax www.tessco.com sales@tessco.com Hutton Communications Dallas, TX 75284 1-877-648-8866 (US) 1-877-762-8274 fax 1-800-265-8685 (Canada) www.huttoncom.com sales@huttoncom.com Please visit our website at www.telewave.com/sales.html for a list of current US sales representatives. TWDS-0008 Rev. 3/16 CONTENTS SECTION 1 SECTION 2 SECTION 3 SECTION 4 SECTION 5 SECTION 6 SECTION 7 SECTION 8 INDEX TRANSMITTER COMBINING . . . . . . . . . . . . . . . . . . . . . 3 RECEIVER MULTICOUPLERS . . . . . . . . . . . . . . . . . . . . 28 POWER MONITORING . . . . . . . . . . . . . . . . . . . . . . . . 64 ISOLATORS AND LOADS . . . . . . . . . . . . . . . . . . . . . . . 75 CAVITIES & FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 DUPLEXERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 ANTENNAS COLLINEAR . . . . . . . . . . . . . . . . . . . . . . . . . 196 DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 YAGI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 WIDEBAND . . . . . . . . . . . . . . . . . . . . . . . . . 294 POWER DIVIDERS, COUPLERS. . . . . . . . . . 302 TECHNICAL NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . 306 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314 1 TRANSMITTER COMBINERS 1 TRANSMITTER COMBINERS Cavity-Ferrite Low Loss Low-loss combiners use one or more tuned cavities and a dual-junction isolator for each channel to maximize isolation between transmitters, with the lowest possible insertion loss. Ceramic Ceramic enhanced cavities have the same or greater performance as full size cavities, but in a smaller package. This greatly reduces the volume and rack space of combiners which use these cavities. Hybrid Hybrid combiners make use of a hybrid coupler and dual isolator for each transmitter. The coupler allows frequencies to be combined with no minimum spacing, but will have higher insertion loss. Pass-Notch A pass-notch combiner uses a combination of pass and notch cavities arranged so that each transmitter sees a low impedance path to the antenna, but is isolated from all other transmitters. LOWBAND COMBINERS Telewave Lowband and Midband Combiners offer high performance with industry-standard Telewave reliability. Telewave is one of the few remaining manufacturers of full size, high-"Q" cavity filters between 30 and 88 MHz. These filters can be deployed in a number of configurations for low band combining and receiver filtering. The M101-030-5T8R series uses 16 cavities to combine 5 transmitters in the 37 MHz band and 8 receivers between 47-49 MHz, with transmitter spacing of only 100 KHz. Telewave has also designed a unique system to combine 2 transmitters in the 45 MHz band with 100 KHz separation, which employs custom designed Telewave hybrid couplers and a dual-cavity sideband filter. Lowband systems present a number of operational challenges, but Telewave has the tools to custom design a complete filtering system for any requirement. 30 - 88 MHz M101-030-5T8R 6 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1010 Rev. 8/09 TRANSMITTER COMBINERS M104-150-4TPC 4 CHANNEL LOW LOSS COMBINER The M104-150-4TPC Low Loss VHF Combiner offers the same high performance as our standard low loss combiners, in a much smaller package. State of the art technology allows us to create one of the world's smallest low loss combiners. The M104-150-4TPC combines up to 4 channels per unit, with 300 KHz separation, in only 8.75" of standard rack space. The modular combining units can be grouped for up to 16 channels to accommodate system expansion. The optional receiver system utilizes the Telewave TPMC-1543 multicoupler for enhanced receiver performance, and distribution to 4 receivers. 148 - 170 MHz 1 SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. / cm Weight lb. (kg) 148-170 MHz 1-4 channels into 1 antenna 300 KHz 100 watts per channel 50 ohms / 1.25:1 3.4 dB - 4 ch. at 300 KHz spacing 75 dB 70 dB 90 dB 4" square / 1/4 wave -30°C to +60°C 19" rack mount / N Female 8.75 x 19 x 12.5 (21.6 x 48.3 x 31.75) 32 (14.5) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 7 TWDS-1023 Rev. 2/11 148 - 174 MHz M108-150-TRM SERIES LOW LOSS VHF COMBINER The M108-150-TRM series uses up to ten 8", high "Q" low-loss cavities mounted on a standard 19" x 72" rack. These combiners are available in a vertical or horizontal configuration, depending on site requirements. Up to 8 cavities can be mounted vertically in two groups, or up to 10 cavities can be mounted horizontally on two 5-channel panels. The vertical configuration is useful for installation in limited space or direct wall mounting. Each cavity also contains internal support for the tuner assembly specifically to enable horizontal mounting. Optional power monitoring for each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C wattmeter panel uses only 1.75" of rack space. An optional receiver system can be built around the Telewave compact preselector series, or full-size cavities as needed. Depending on the application, the TPCP-1544C or TPCP-1556 preselector may be mounted in the upper portion of a 72" or 84" rack, along with a 1RU receiver panel for up to 16 channels. With new narrowband channel assignments, proper filtering is even more critical. The M108-150TRM series allows operators of high-density VHF systems to take advantage of new technology, and enhance the performance of existing systems. M108-150-5TRM with preselector, power monitoring, and RX panel M108-150-8TRM vertical mounting SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (std. / opt.) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. / cm Weight lb. (kg) 148-174 MHz 1-10 channels into 1 or 2 antennas 125 KHz 100 / 150 watts per channel 50 ohms / 1.25:1 3.25 dB - 5 ch. at 250 KHz spacing 4.0 dB - 5 ch. at 150 KHz spacing 75 dB 70 dB 90 dB 8" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 24.5 x 19 x 26 / 62 x 48.3 x 66 150 (68.1) 5 ch. 8 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1029 Rev. 10/12 M101-150-8TRM19 LOW LOSS VHF COMBINER FOR CLOSE SPACING 148 - 174 MHz 1 TRANSMITTER COMBINERS The M101-150-8TRM19 uses up to With new narrowband channel eight 10", high "Q" low-loss cavities assignments, proper filtering is mounted on a standard 19" x 72" even more critical. The M101-150rack. This combiner provides as TRM19 series allows operators of much as 75 dB isolation for each high-density VHF systems to take transmitter, with spacing as close advantage of new technology, as 105 KHz. Each channel has a and enhance the performance of separate isolator with 60 Watt existing systems. load (standard), and all tuning is accessible from the front panel. Optional power monitoring for each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C wattmeter panel uses only 1.75" of rack space. The optional receiver system is built around the Telewave compact preselector series. Depending on the application, the TPCP-1544C or 1546C preselector may be integrated directly into the upper portion of the M101-150 84" rack. The 1RU receiver panel also mounts straight into the rack, preserving valuable site floor space. SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (std. / opt.) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Rack dimensions (HWD) in. (cm) Weight lb. (kg) 148-174 MHz 1-8 channels into 1 or 2 antennas 105 KHz 100 / 150 watts per channel 50 ohms / 1.25:1 3.0 dB - 5 ch. at 250 KHz spacing 3.8 dB - 5 ch. at 150 KHz spacing 75 dB 70 dB 90 dB 10" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 84 x 20 x 26 (214 x 51 x 66) 250 (113.5) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com OPTIONAL 100 WATT LOADS SHOWN All specifications subject to change without notice 9 TWDS-1011 Rev. 10/12 148 - 174 MHz M101-150-8TRM LOW LOSS VHF COMBINER The Telewave M101-150 Low Loss VHF Combiner is a unique, fully self-contained transmitter and receiver combining system. The custom welded 24" steel frame provides a rugged enclosure for all system components. This integrated design allows channels to be added, retuned, or removed in the field at any time, without disrupting other active channels. The 24" x 48" rack handles up to 8 channels and 1 or 2 antennas. With new narrowband channel assignments, proper filtering is even more critical. 10-inch High"Q" cavities with dual isolators provide 75 dB isolation between channels, and the optional receiver panel drives multiple receivers from a single antenna. The PM8C2S wattmeter panel allows forward or reverse power monitoring for each channel, or total power to each antenna. The M101-150 series allows system operators to take advantage of new technology, and enhance the performance of existing systems. FEATURES · ALL TUNING FROM FRONT · 8 TRANSMITTERS INTO ONE ANTENNA · INTEGRATED RCVR PANEL · SELF-CONTAINED, BUILDING BLOCK CONCEPT · LESS THAN 3 dB INSERTION LOSS WITH PROPER FREQUENCY SELECTION · ALL CONNECTIONS AT TOP OF RACK · 75 dB TX TO TX PROTECTION · 130 dB RX INTERMOD PROTECTION WITH RX PNL. · RF POWER MONITORING FOR ALL CHANNELS AND ANTENNA · REMOTE TX KEYING · FIELD TUNABLE SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (std. / opt.) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Rack dimensions (HWD) in. (cm) Weight lb. (kg) 148-174 MHz 1-8 channels into 1 or 2 antennas 105 KHz 100 / 150 watts per channel 50 ohms / 1.25:1 3.0 dB - 5 ch. at 250 KHz spacing 3.8 dB - 5 ch. at 150 KHz spacing 75 dB 70 dB 90 dB 10" diameter / 1/4 wave -30°C to +60°C 24" rack mount / N Female 48 x 24 x 31 (122 x 61 x 79) 250 (113.5) 10 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1014 Rev. 10/12 M106-450-4/8TPC COMPACT TRANSMITTER COMBINER PANELS 400 - 512 MHz 1 TRANSMITTER COMBINERS The Telewave M106-450-4TPC and 8TPC Compact Low Loss Combiner Panels are designed for new, narrowband technologies. Sixinch diameter high "Q" cavities and horizontal mounting dual isolators provide high performance in only 7RU (12.25"). All components in these fieldexpandable combiners are completely passive. This design allows for front panel tuning, simplifing installation and maintenance, and allows for addition of channels without any disruption of service. These combiners are shipped without racks, for mounting in existing installations. FEATURES · ULTRA COMPACT 4 CH. ONLY 12.25" HIGH · 1-8 TRANSMITTERS INTO ONE ANTENNA · LESS THAN 3 dB INSERTION LOSS (4 CH.) · MODULAR PANELS SIMPLIFY EXPANSION · COMPLETELY SELFCONTAINED · LOW COST PER CHANNEL · FULLY FIELD TUNABLE · 80 dB TX TO TX PROTECTION SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 400-512 MHz 1-8 channels into 1 or 2 antennas 300 KHz 150 watts per channel 50 ohms / 1.25:1 2.9 dB - 4 ch. at 300 KHz spacing 3.4 dB - 8 ch. at 300 KHz spacing 80 dB 75 dB 90 dB 6" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 12.25 x 19 x 17 (31.1 x 48.3 x 43.2) 4 ch. 60 (27.2) MAJOR OPTIONS · HEAVY DUTY 19" RACKS · POWER MONITORING · WATTMETER PANEL · RECEIVER MULTICOUPLER · EXPANSION KITS TO 8 CHANNELS (M106-450-1T) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 11 TWDS-1031 Rev. 7/09 M107-250, 350, 450 TP SERIES LOW LOSS TRANSMITTER COMBINER PANELS Telewave M107-250, -350, and -450 Low Loss Combiner panels are designed for new, narrowband technologies. All components in these fieldexpandable combiners are completely passive. This design allows front panel tuning, simplifies installation and maintenance, and allows for addition of channels without any disruption of service. Each panel fits a standard 19" rack, and allows up to 4 or 6 channels. Additional channels can be added to a panel without disrupting existing users. These combiners are shipped without racks, for mounting in existing installations. The actual height and depth of each panel can vary with frequency. Lower frequencies require longer cavities. FEATURES · ALL TUNING FROM THE FRONT · 4 OR 6 CHANNELS PER PANEL INTO ONE ANTENNA · LESS THAN 3 dB INSERTION LOSS · MODULAR PANELS SIMPLIFY EXPANSION · LOW COST PER CHANNEL · FULLY FIELD TUNABLE · 80 dB TX TO TX PROTECTION 200 - 512 MHz M107-250-TP 200-300 MHz M107-350-TP 300-400 MHz M107-450-TP 400-512 MHz M107 TP 4 CHANNELS SPECIFICATIONS Frequency ranges Channels Channel separation (min) Input power (std. / opt.) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dim. typ. (HWD) in. (cm) (Panel height varies with freq.) Weight lb. (kg) 200-512 MHz 4 or 6 channels into one antenna 250 KHz 100 / 150 watts per channel 50 ohms / 1.25:1 3.25 dB at 275 KHz spacing 80 dB 75 dB 90 dB 7" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 4 ch. 17.5 x 19 x 26 (44.5 x 48.3 x 66) 6 ch. 24.5 x 19 x 26 (62.2 x 48.3 x 66) 4 ch. 42 (19.1) / 6 ch. 58 (26.3) 12 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com M107 TP 6 CHANNELS All specifications subject to change without notice TWDS-1007 Rev. 6/11 TRANSMITTER COMBINERS M107-250, 350, 450 TRM SERIES EXPANDABLE LOW LOSS TRANSMITTER COMBINERS Telewave M107-250, -350, and To meet international requirements, -450 Low Loss Combiners are special configurations and expandesigned for new, narrowband sion kits are available. technologies. All components in these field-expandable combiners are completely passive, with the exception of the optional receiver distribution amplifier. The compact layout is enclosed in a rugged steel FEATURES · ALL TUNING FROM THE FRONT frame. Optional power monitoring for each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C wattmeter panel uses only 1.75" of rack space. · UP TO 14 TRANSMITTERS INTO ONE ANTENNA · LESS THAN 3 dB INSERTION LOSS · ALL CONNECTIONS AT TOP OF RACK An optional receiver system can be built around the Telewave compact preselector series, or full- · COMPLETELY SELF CONTAINED · LOW COST PER CHANNEL size cavities as needed. Depending on the application, a 4 or 6 cavity compact preselector may be · FULLY FIELD TUNABLE · 80 dB TX TO TX PROTECTION mounted in the upper portion of a 72" or 84" rack, and a 1RU receiver panel with 8 or 16 channels. 200 - 512 MHz M107-250-8TRM 200-300 MHz M107-350-8TRM 300-400 MHz M107-450-8TRM 400-512 MHz 1 SPECIFICATIONS Frequency ranges Channels Channel separation (min) Input power (std. / opt.) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Rack dimensions (HWD) in. (cm) Weight lb. (kg) 200-512 MHz 1-14 channels into 1 or 2 antennas 250 KHz 100 / 150 watts per channel 50 ohms / 1.25:1 3.25 dB at 275 KHz spacing 80 dB 75 dB 90 dB 7" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 72 x 20 x 26 (183 x 51 x 66) (Depth varies with frequency) 200 (91) Shown with Optional Receiver Distribution Panel Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 13 TWDS-1001 Rev. 11/12 M108-450-TRM SERIES LOW LOSS UHF COMBINER The M108-450-TRM series uses up to ten 8", high "Q" low-loss cavities mounted on a standard 19" x 72" rack. Optional power monitoring for each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C wattmeter panel uses only 1.75" of rack space. An optional receiver system can be built around a Telewave UHF preselector. Depending on the application, the TPCP-4544 or TPCP-4546 preselector may be mounted in the upper portion of a 72" or 84" rack, and a 1RU receiver panel with 8 or 16 channels. With new narrowband channel assignments, proper filtering is even more critical. The M108450-TRM series allows operators of high-density UHF systems to take advantage of new technology, and enhance the performance of existing systems. 400 - 512 MHz M108-450-5TRM with preselector, power monitoring, and RX panel SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 400-512 MHz 1-10 channels into 1 or 2 antennas 250 KHz 150 watts per channel 50 ohms / 1.25:1 3.5 dB - 5 ch. at 250 KHz spacing 80 dB 75 dB 90 dB 8" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 24.5 x 19 x 14 (62 x 48.3 x 35.6) 150 (68.1) 5 ch. 14 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1036 Rev. 10/12 M108-450-TRM3Q SERIES LOW LOSS UHF COMBINER 400 - 512 MHz 1 TRANSMITTER COMBINERS The M108-450-TRM3Q series uses up to ten 8-inch, high "Q" ¾-wave low-loss cavities mounted on a standard 19" x 72" rack. These combiners are available in a vertical or horizontal configuration as required. Up to 8 cavities can be mounted vertically in two groups, or up to 10 cavities can be mounted horizontally on two 5-channel panels. The vertical configuration is useful for installation in limited space or direct wall mounting. Each cavity also contains internal support for the tuner assembly specifically to enable horizontal mounting. Optional power monitoring for each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C wattmeter panel uses only 1.75" of rack space. An optional receiver system can be built around the Telewave compact preselector series, or fullsize cavities as needed. Depending on the application, the TPCP-4544 or TPCP-4546 preselector may be mounted in the upper portion of a 72" or 84" rack, and a 1RU receiver panel with 8 or 16 channels. With new narrowband channel assignments, proper filtering is even more critical. The M108-450TRM3Q series allows operators of high-density UHF systems to take advantage of new technology, and enhance the performance of existing systems. M108-450-5TRM3Q with preselector, power monitoring, and RX panel M108-450-8TRM3Q vertical mounting SPECIFICATIONS Frequency ranges Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 400-512 MHz 1-10 channels into 1 or 2 antennas 175 KHz 150 watts per channel 50 ohms / 1.25:1 3.6 dB - 5 ch. at 200 KHz spacing 80 dB 75 dB 90 dB 8" diameter / 3/4 wave -30°C to +60°C 19" rack mount / N Female 24.5 x 19 x 26 (62 x 48.3 x 66) 150 (68.1) 5 ch. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 15 TWDS-1037 Rev. 10/12 400 - 512 MHz M101-450-8TRM-193Q LOW LOSS UHF COMBINER FOR CLOSE SPACING The M101-450-8TRM-193Q is a high portion of the M101-450 84" rack. power, high capacity UHF combining A 1RU receiver panel with 8 or 16 system. The system combines up to channels also mounts straight into eight transmitters using 10-inch, the rack, preserving valuable site high "Q", ¾-wave low-loss cavities floor space. mounted on a standard 19" x 72" rack. This design provides as much as 75 dB isolation for each transmitter, with spacing as close as 175 KHz. Each channel has a separate dual isolator, and all tuning is accessible from the front panel. With new narrowband channel assignments, proper filtering is even more critical. The M101-450TRM193Q series allows operators of high-density UHF systems to take advantage of new technology, and enhance the performance of Optional power monitoring for existing systems. each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C metering panel uses only 1.75" of vertical rack space. The optional receiver system is built around Telewave UHF preselectors. Depending on the application, the TPCP-4544, 4546, or 4548 preselector may be integrated directly into the upper SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Rack dimensions (HWD) in. (cm) Weight lb. (kg) 400-512 MHz 1-8 channels into 1 or 2 antennas 175 KHz 150 watts per channel 50 ohms / 1.25:1 3.25 dB - 5 ch. at 250 KHz spacing 3.75 dB - 5 ch. at 200 KHz spacing 80 dB 75 dB 90 dB 10" diameter / 3/4 wave -30°C to +60°C 19" rack mount / N Female 84 x 20 x 26 (214 x 51 x 66) 250 (113.5) 16 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com OPTIONAL 100 WATT LOADS SHOWN All specifications subject to change without notice TWDS-1020 Rev. 10/12 TRANSMITTER COMBINERS M101-450-8TRM LOW LOSS UHF COMBINER The Telewave M101-450 Low Loss UHF Combiner is a unique, fully self-contained transmitter and receiver combining system. The custom welded 24" steel frame provides a rugged enclosure for all system components. This integrated design allows channels to be added, retuned, or removed in the field at any time, without disrupting other active channels. The 24" x 48" rack handles up to 8 channels and 1 or 2 antennas. With new narrowband channel assignments, proper filtering is even more critical. 10-inch High"Q" cavities with dual isolators provide 80 dB isolation between channels, and the optional receiver panel drives multiple receivers from a single antenna. The PM8C2S wattmeter panel allows forward or reverse power monitoring for each channel, or total power to each antenna. The M101-450 series allows system operators to take advantage of new technology, and enhance the performance of existing systems. FEATURES · ALL TUNING FROM FRONT · 8 TRANSMITTERS INTO ONE ANTENNA · INTEGRATED RCVR PANEL · SELF-CONTAINED, BUILDING BLOCK CONCEPT · LESS THAN 3 dB INSERTION LOSS WITH PROPER FREQUENCY SELECTION · ALL CONNECTIONS AT TOP OF RACK · 80 dB TX TO TX PROTECTION · 130 dB RX INTERMOD PROTECTION WITH RX PNL. · RF POWER MONITORING FOR ALL CHANNELS AND ANTENNA · REMOTE TX KEYING · FIELD TUNABLE 400 - 512 MHz 1 M101-450-8TRM-8R (with optional preselector and receiver panel) SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Dimensions (HWD) in. (cm) Weight lb. (kg) 400-512 MHz 1-8 channels into 1 or 2 antennas 250 KHz 150 watts per channel 50 ohms / 1.25:1 2.8 dB at 275 KHz spacing 80 dB 75 dB 90 dB 10" diameter / 1/4 wave -30°C to +60°C 24" rack mount / N Female 48 x 24 x 24 (122 x 61 x 61) 150 (68.1) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 17 TWDS-1016 Rev. 10/12 M108-760-10TRM LOW LOSS 700-800 MHz COMBINER The Telewave M108-760-TRM An optional receiver system can transmitter combiner covers be built around the Telewave 746-806 and 800-869 MHz. This compact preselector series, or full- combiner features 8-inch, ¾-wave size cavities as needed. Depending cavities for close channel spacing, on the application, the TPCP-7644 and allows 700 and 800 MHz preselector may be mounted in the channels to be provisioned in the upper portion of a 72" or 84" rack, same rack. and a 1RU receiver panel with 8 or Each combiner covers a single 16 channels. band, and is a modular unit on a Narrowband 700 MHz spectrum 24.5-inch panel. Each 19-inch rack provides Public Safety system combines up 10 channels into a operators with new channels for common antenna, with optional capacity expansion. The M108- duplexer, preselector, and receiver 760-TRM series allows operators to distribution. Individual channels flexibly deploy spectrum resources are field-replaceable within the in 700 and 800 MHz bands, at new applicable band without causing or existing sites. downtime to other channels. Optional power monitoring for each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C wattmeter panel uses only 1.75" of rack space. 746 - 806 MHz 800 - 869 MHz SPECIFICATIONS Frequency ranges Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 746-806, 800-869 MHz 1-10 channels into 1 or 2 antennas 250 KHz 150 watts per channel 50 ohms / 1.25:1 4.25 dB - 5 ch. at 250 KHz spacing 4.8 dB - 10 ch. at 250 KHz spacing 80 dB 75 dB 90 dB 8" diameter / 3/4 wave -30°C to +60°C 19" rack mount / N Female 24.5 x 19 x 16 (62 x 48.3 x 40.6) 150 (68.1) 18 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1034 Rev. 10/12 TRANSMITTER COMBINERS 851 - 869 MHz M106-860-5TP/10TP 1 COMPACT EXPANDABLE TRUNKING COMBINER PANELS The Telewave M106-860 Compact The advanced mechanical design Trunking Combiner is an industry of Telewave high "Q" cavities leader for excellence in low-loss assures maximum long-term system combiner technology. performance. The completely passive combining technique with front panel tuning access simplifies installation and maintenance, and allows for the addition of new channels without any disruption of service. Heavy duty 19" racks, duplexers, and receiver multicoupler systems are available as upgrades. CLOSE-UP OF REAR PANEL (10 CH.) Each combiner panel is field expandable up to five channels. Additional pre-tuned combiner panels can be added at any time. Valuable site space is conserved when using efficient Telewave combiners. The modular building-block construction means no specialized test equipment is required. (Rack not included) SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 851-869 MHz 1-10 channels into 1 or 2 antennas 500 KHz 100 watts per channel 50 ohms / 1.25:1 2.0 dB - 5 ch. at 1 MHz spacing 3.2 dB - 10 ch. at 500 KHz spacing 80 dB 65 dB 90 dB 6" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 12.25 x 19 x 17 (31 x 48.3 x 43.2) 75 (34) 5 ch. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 19 TWDS-1003 Rev. 10/12 851 - 869 MHz M107-860-5TRM-HP, 10TRM-HP COMPACT HIGH POWER TRUNKING COMBINER The Telewave M107-860-5TRM-HP Low Loss High Power Combiner is designed for trunking applications up to 175 watts per channel, with up to 10 channels per rack. The combiner uses 7-inch, ¾ wave cavities, and channel expansion or maintenance can be performed without disruption of the system. RF power metering is switchable for forward and reverse directions for each transmitter and antenna. Convenient remote transmitter keying is included on the RF wattmeter panel. All high power trunking combiners are shipped in a 19" x 72" Rack, with power monitoring, wattmeter panel with remote keying, 175 watt isolator, and -50 dB sampler on 2nd stage isolator load port (75 watt load). Input connectors are N Female and output is 7-16 DIN-F. Standard cabling is high-temp RG393. FEATURES · FIELD TUNABLE · 10 TRANSMITTERS INTO ONE ANTENNA · POWER MONITORING FOR ALL CHANNELS AND ANTENNA · -50 dB RF OUTPUT POWER SAMPLER - EACH CHANNEL OPTIONS · RECEIVER PANEL - 1RU · 500 WATT DUPLEXER - 15 MHz PASSBAND w/ 7-16 DIN · RG-393 PHASING HARNESS WITH 7-16 DIN CONNECTORS FOR (2) 5-CHANNEL PANELS · HIGH POWER 5-WAY 7-16 DIN JUNCTION SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 851-869 MHz 1-10 channels into 1 or 2 antennas 250 KHz 175 watts per channel 50 ohms / 1.25:1 2.2 dB - 5 ch. at 1 MHz spacing 4.25 dB - 5 ch. at 250 KHz spacing 3.2 dB - 10 ch. at 500 KHz spacing 85 dB 80 dB 90 dB 7" diameter / 3/4 wave -30°C to +60°C 19" rack mount / N Female, 7-16 DIN 17.5 x 19 x 17 (44.5 x 48 x 43) 150 (68.1) 5 ch. 20 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1002 Rev. 8/09 M101-860-10TRM LOW LOSS 800 MHz COMBINER 806 - 869 MHz 1 TRANSMITTER COMBINERS The Telewave M101-860 Trunking Convenient remote transmitter Combiner is an industry leader in keying is included on the RF low-loss combiner technology. Ease wattmeter panel. of installation and maintenance is accomplished by front panel tuning. All rack-mount five channel combiners are field expandable to 10 channels by the addition These trunking combiners are of pre-tuned combiner panels. complete packages, including The modular building-block 19" x 72" rack or heavy duty steel construction means no specialized cabinet with front and rear locking test equipment is required. doors, receiver distribution system, preselector, and power monitoring system. The advanced mechanical design of the Telewave 8-inch high "Q" cavities assures maximum long- The completely passive combining term system performance. All technique allows for maintenance cables are easily accessible from and addition of channels without the front panel. disruption of the system. Valuable site space is conserved when using efficient Telewave designed combiners, and RF power metering is a standard feature. All forward and reverse power measurements are switchable for each transmitter and antenna. SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 806-869 MHz 1-10 channels into 1 or 2 antennas 500 KHz (250 KHz with 3Q cavities) 150 watts per channel 50 ohms / 1.25:1 2.0 dB - 5 ch. at 1 MHz spacing 3.2 dB - 10 ch. at 500 KHz spacing 85 dB 80 dB 90 dB 8" diameter / 1/4 wave -30°C to +60°C 19" rack mount / N Female 24.5 x 19 x 16 (62 x 48.3 x 40.6) 75 (34) 5 ch. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 21 TWDS-1017 Rev. 7/11 851 - 869 MHz TC860 CERAMIC ENHANCED TRUNKING COMBINER The Telewave Ceramic Enhanced 860 MHz Trunking Combiner brings ceramic technology to trunking system operators. The TC860 combiner requires only 7 inches of rack space, and the 4" ceramic cavities provide the same performance as conventional, eightinch ¾-wavelength cavities. The Telewave Ceramic Enhanced combiner is the best choice when site space is at a premium. Ceramic Enhanced Resonators allow combining of channels as close as 250 KHz with reasonable insertion loss. Fully temperature compensated components ensure frequency stability throughout the entire temperature range. The unique design also allows the cavity to be tuned under the full 80 watts of input power. To fully complement this compact combiner, the optional PM10C2S1C wattmeter panel requires only 1 rack unit of panel space. The wattmeter panel provides convenient transmitter keying and continuous monitoring of combiner performance. If per-channel monitoring is required, additional power monitors are typically mounted on a separate 2RU panel. The TC860 combiner is field expandable to 10 channels with pretuned expansion kits. This building block concept allows the installation of new channels without the need for specialized test equipment. SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 851-869 MHz 1-5 channels into 1 antenna 250 KHz 80 watts per channel 50 ohms / 1.25:1 2.2 dB - 5 ch. at 1 MHz spacing 2.8 dB - 5 ch. at 500 KHz spacing 3.2 dB - 5 ch. at 250 KHz spacing 80 dB 70 dB 90 dB 4" diameter ceramic / 1/4 wave -0°C to +50°C 19" rack mount / N Female 7 x 19 x 13 (17.8 x 48.3 x 33) 36 (16.3) 5 ch. 22 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1021 Rev. 10/12 TW860-2HRB1, TW860-4HRB1 COMPACT HYBRID COMBINERS 851 - 869 MHz 1 TRANSMITTER COMBINERS TW860-2HRB1 TW860-4HRB1 Te l e w a v e C o m p a c t H y b r i d These compact combiners provide filter on each channel removes any Combiners allow transmit ter high performance in a very small spurious products. combining with close frequency spacing that is not practical for cavity-ferrite combiners. Combining adjacent channels is possible, even two transmitters on the same frequency. The TW860-2HRB1 and 4HRB1 will handle 2 or 4 channels respectively, with reasonable insertion loss. space. Both combiners occupy only two rack units each (3.5") of vertical space on a 19" rack. Each combiner is a broadband device, and is pretuned for 800 MHz SMR/ ESMR, Trunking, or NPSPAC. No additional tuning is required during installation. A harmonic The TW860-2HRB1 and -4HRB1 operate as stand-alone devices, and can be integrated into any standard Telewave cavity/ferrite system to provide maximum flexibility in frequency assignment. Contact our System Engineering Department for custom integration, and high power applications. SPECIFICATIONS Frequency range 851-869 MHz Channels 2 or 4 Bandwidth 10-30 MHz Input power (max) 100 watts per channel Impedance / Input VSWR (max) 50 ohms / 1.3:1 Insertion loss: 2 ch. / 4 ch. 3.8 dB / 7.0 dB TX to TX isolation 90 dB Antenna to TX isolation 65 dB 2nd Harmonic attn. 65 dB Temperature range -30° to +60°C Mounting / Connectors 19" rack mount / N Female Dimensions (HWD) in. (cm) 2 CH 3.5 x 19 x 11.25 (8.9 x 48.3 x 28.6) 4 CH 3.5 x 19 x 16.75 (8.9 x 48.3 x 42.5) Weight Net / Ship lb (kg) 2 CH 15 (6.8) / 30 (13.6) 4 CH 20 (9.1) / 40 (18.2) Enclosure Alodined Aluminum BLOCK DIAGRAM TW860-2HRB1 TWO CHANNEL HYBRID TX 1 TX 2 T8660N TLF-860 TWH-900 ANTENNA TWL-60 TWL-100 TZM-900 BLOCK DIAGRAM TW860-4HRB1 FOUR CHANNEL HYBRID TX 1 TX 2 T8660N TLF-860 TWH-900 ANTENNA TWL-35 TWL-100 TZM-900 TX 3 TX 4 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 23 TWDS-1015 Rev. 10/12 896 - 941 MHz M108-900-10TRM3Q LOW LOSS 900 MHz COMBINER The Telewave M108-900-TRM preselector may be mounted in the transmitter combiner covers 896- upper portion of a 72" or 84" rack, 941 MHz. This combiner features and a 1RU receiver panel with 8 or 8-inch, ¾-wave cavities for close 16 channels. channel spacing. The M108-900-TRM3Q series Each combiner covers the full provides a new option for 900 band, and is a modular unit on a MHz system operators to deploy 24.5-inch panel. Each 19-inch rack systems with standard spacing and combines up 10 channels into a normal insertion loss. common antenna, with optional duplexer, preselector, and receiver distribution. Individual channels are field-retunable without causing downtime to other channels. Optional power monitoring for each channel is available, as well as remote keying for each transmitter. The PM10C2S-1C wattmeter panel uses only 1.75" of rack space. An optional receiver system can be built around the Telewave compact preselector series, or fullsize cavities as needed. Depending on the application, the TPCP-8644 SPECIFICATIONS Frequency range Channels Channel separation (min) Input power (max) Impedance / Input VSWR (typ.) Insertion loss per ch. (typ.) TX-to-TX isolation (typ.) Antenna to TX isolation (typ.) 2nd harmonic suppression (typ.) Cavity size Operating temperature Mounting / Connectors Panel dimensions (HWD) in. (cm) Weight lb. (kg) 896-941 MHz 1-10 channels into 1 or 2 antennas 250 KHz 150 watts per channel 50 ohms / 1.25:1 4.25 dB - 5 ch. at 250 KHz spacing 4.8 dB - 10 ch. at 250 KHz spacing 80 dB 75 dB 90 dB 8" diameter / 3/4 wave -30°C to +60°C 19" rack mount / N Female 24.5 x 19 x 26 (62 x 48.3 x 66) 150 (68.1) 5 ch. 24 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1035 Rev. 7/09 TRANSMITTER COMBINERS M101-900-10TRMH HIGH CAPACITY 900 MHz HYBRID COMBINER The Telewave 900 MHz Hybrid Trunking Combiner is the industry leader for excellence in hybrid combiner technology. This design allows any transmitter frequency spacing, even transmitters on the same frequency for hot standby. The M101-900 combiner systems are priced as a complete transmitter combining package, with a 19" steel rack, receiver distribution system with preselector, sideband filters as needed, and power monitoring. The passive combining design reduces maintenance requirements, and allows simple reconfiguration of antennas to meet system coverage requirements. The rack mount ten-channel combiners are field expandable to twenty channels. Expansions are accomplished by the addition of the pre-tuned duplexer cavity panels. Modular building block construction means no specialized test equipment is required. All components are easily accessible from the back of the rack. RF power metering is a standard feature. All forward and reverse power measurements are switchable for each transmitter. Up to five antennas can be monitored for VSWR. Convenient remote transmitter keying is included on the wattmeter panel. The advanced design of the Telewave hybrid combiner assures maximum long-term system performance. Special high power combiners up to 250 watts are available upon request. 896 - 941 MHz 1 TRANSMITTER COMBINER Frequency range 896-941 MHz Channel separation (min) 12.5 KHz Input power (max) 150 watts per channel Temperature -30°C to +60°C TX to TX isolation (typ.) 100 dB Antenna to TX isolation (typ.) 80 dB Insertion loss (typ) 5 Antenna System (4 TX and 1 RX) 3.1 dB (2 channels to each TX or 2 channels duplexed to RX ant.) 3 Antenna System (2 TX and 1 RX Ant) 6.3 dB (4 channels to each TX) 3.1 dB (2 channels duplexed to RX ant.) 2 Antenna System (1 TX and 1 RX) 9.3 dB (8 channels to TX ant.) Note: Add 0.4 dB for each isolator, duplexer or sideband filter. M101-900-15TRM RECEIVER SYSTEM Frequency range Port isolation (typ.) Power input 3rd Order int. (typ.) Noise figure (typ.) System Gain (typ.) Temperature Connectors Channels Mounting Test port 896-941 MHz 25 dB 120 or 240 VAC +15 VDC +36 dB 2.5 dB +4 to +6 dB -40°C +60°C N Female 8-32 19" Rack mount -20 dB Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 25 TWDS-1018 Rev. 7/09 BANDPASS/NOTCH COMBINERS 1 NOTCH, 1-3 PASS CAVITIES Telewave Pass-Notch Combiners device to maintain proper energy offer excellent performance, and flow in the combining network. The several unique characteristics. pass cavities form a highly selective Additional frequencies can be filter which effectively isolates each added without retuning the entire node. The nodes are arranged in system. Installation is simplified and ascending order, with the highest off-air time is minimized. Splitting of frequency nearest the antenna. transmitter and receiver systems is not necessary. Contact Telewave for complete engineering assistance with your Each combiner consist s of a system. 8" diameter notch cavity and one to three 8" pass cavities. A cavity-mounted dual isolator is recommended to suppress intermodulation and third harmonics. The notch cavity performs the function of a steering 66 - 512 MHz M101-150-1T-3PN WITH OPTIONAL DUAL ISOLATOR SPECIFICATIONS Frequency ranges Insertion loss Impedance VSWR (max) Input power (max) (without isolators) Cavity size Temperature Size (HWD) in. Weight lb. M101-70-xx M101-150-xx M101-450-xx 66-88 MHz 136-174 MHz 400-512 MHz 0.5 - 3.0 dB (adjustable) 50 ohms 1.5:1 350 watts at 1.7 dB insertion loss 150 watts at 3.0 dB insertion loss 8" diameter -30°C to +60°C M101-70-xx M101-150-xx M101-450-xx M101-70-1T M101-150-1T M101-450-1T 53 x 19 x 8.5 / 17 (2PN, 3PN) 22 x 19 x 8.5 / 17 (2PN, 3PN) 16 x 19 x 8.5 / 17 (2PN, 3PN) -1PN 24 -2PN 35 -3PN 46 -1PN 17 -2PN 25 -3PN 33 -1PN 12 -2PN 17 -3PN 20 26 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-1019 Rev. 6/12 HYBRID COMBINERS 2 OR 4 CHANNELS 118 - 960 MHz 1 TRANSMITTER COMBINERS Telewave Hybrid Combiners allow transmitter combining with close frequency spacing that is not practical for cavity-ferrite combiners. Combining adjacent channels is possible, even two transmitters on the same frequency. These combiners are configured in sets of two or four channels, and maintain reasonable insertion losses. Telewave hybrid combiners use a minimal amount of 19" rack space. Two channel units require 5.25" rack space, and 10.5" for each four channel combiner. There is no tuning required during installation. Each channel is equipped with a harmonic filter to remove any spurious products. The basic hybrid design can also be integrated into any standard Telewave cavity-ferrite combiner system to provide outstanding flexibility in frequency selection. High power is available in all frequency bands. Contact Telewave for custom integration and applications above 150 watts. TW450-4HRA1 MODEL NUMBER FREQUENCY ISOLATION (dB) BAND (MHz) TX-TX ANT-TX INSERTION LOSS (dB) TWO CHANNEL WITH SINGLE ISOLATORS - PANEL SIZE 5.25" H x 19" W TW150-2HRA1 118-174 70 33 3.8 TW220-2HRA1 216-250 70 33 3.8 TW450-2HRA1 406-512 70 33 3.7 TW760-2HRA1 763-869 70 33 3.6 TW900-2HRA1 806-960 70 33 3.6 TWO CHANNEL WITH DUAL ISOLATORS - PANEL SIZE 5.25" H x 19" W TW150-2HRB1 118-174 100 65 4.0 TW220-2HRB1 216-250 100 65 4.0 TW450-2HRB1 406-512 100 65 3.9 TW760-2HRB1 763-869 100 65 3.8 TW900-2HRB1 806-960 100 65 3.8 FOUR CHANNEL WITH SINGLE ISOLATORS - PANEL SIZE 10.5" H x 19" W TW150-4HRA1 118-174 70 33 6.8 TW220-4HRA1 216-250 70 33 6.8 TW450-4HRA1 406-512 70 33 6.8 TW760-4HRA1 763-869 70 33 6.7 TW900-4HRA1 806-960 70 33 6.7 FOUR CHANNEL WITH DUAL ISOLATORS - PANEL SIZE 10.5" H x 19" W TW150-4HRB1 118-174 100 65 7.2 TW220-4HRB1 216-250 100 65 7.2 TW450-4HRB1 406-512 100 65 7.1 TW760-4HRB1 763-869 100 65 7.0 TW900-4HRB1 806-960 100 65 7.0 SPECIFICATIONS Input power (std. / opt.) 100 / 150 watts per channel Harmonic attenuation (min) 65 dB Temperature range -30°C to +60°C Connector N Female Weight 20-50 lb. depending on model Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 27 TWDS-1022 Rev. 10/12 2 RECEIVER MULTICOUPLERS 2 RECEIVER MULTICOUPLERS Receiver Distribution Panels Receiver Distribution Panels feed multiple receivers from a single antenna, with isolation between each output port. An integral preamplifier compensates for signal losses in the splitters and long cable runs. Compact Distribution Panels Compact Receiver Panels provide 8 or 16 outputs in 1RU (1.75"), and 24 or 32 channels in 2RU (3.5"). This allows RX distribution capability in the same rack as a multi-channel combiner and preselector. Receiver Power Splitters Power splitters divide a low-level signal and distribute it to multiple outputs with isolation between each port. Antenna ports are tuned with a matching network to insure balanced input. Preamplifiers - Bipolar / PHEMT Preamplifiers amplify low-level signals and can improve the noise figure of a receiver system. Bipolar preamps are very rugged and resistant to input overload. PHEMT devices provide a low noise figure and redundant circuitry. Tower Top Preselectors A tower-top preselector improves the noise figure of a receiver system by filtering and amplifying the received signal at the antenna, before cabling losses. Coupling devices transfer DC power up the tower via the feedline. Base Station Preselectors A preselector protects a receiver or group of receivers by filtering out all signals that are not within the operating frequency band. Multi-window preselectors cover more than one segment within a band. Square cavities allow very compact designs for efficient rack layout. TWR2, TWR4 SERIES RECEIVER DISTRIBUTION PANELS 132 - 960 MHz TWR2 SERIES TWR4 SERIES Telewave TWR2 and TWR4 Receiver Distribution Panels provide 2 or 4 isolated 50 ohm receiver outputs from one input, in a compact package. The antenna port is tuned with a matching network to insure a balanced input. A high-gain TLA- series preamp and multi-voltage AC power supply are included on a single 5.25" panel. The preamp can also be powered directly from a DC source. Telewave receiver panels use highquality splitters which provide multiple balanced outputs from one input, with 20-30 dB of isolation between ports. MODEL FREQUENCY PORTS BANDWIDTH GAIN TWR2-150 132-174 MHz 2 26 MHz 0-18 dB TWR2-250 216-250 MHz 2 34 MHz 0-18 dB TWR2-350 300-400 MHz 2 30 MHz 0-18 dB TWR2-450 400-512 MHz 2 40 MHz 0-18 dB TWR2-760 763-824 MHz 2 30 MHz 0-18 dB TWR2-860 806-960 MHz 2 30 MHz 0-18 dB TWR4-150 148-174 MHz 4 26 MHz 0-18 dB TWR4-250 216-250 MHz 4 34 MHz 0-18 dB TWR4-350 300-400 MHz 4 40 MHz 0-18 dB TWR4-450 400-512 MHz 4 40 MHz 0-18 dB TWR4-760 763-824 MHz 4 40 MHz 0-15 dB TWR4-860 806-960 MHz 4 40 MHz 0-15 dB COMMON SPECIFICATIONS Impedance / VSWR (typ) 50 ohms / 1.3:1 Isolation RX-RX (min / typ.) 132-174 MHz: 20 dB / 25 dB 216-960 MHz: 25 dB / 30 dB Noise figure (typ) 2.5 dB Third order intercept +36 dBm Intermodulation (typ) -130 dB for -30 dBm input Temperature range -40°C to +60°C Power requirements AC 100-240 VAC, 50-60 Hz / 0.4 A DC +12 to +24 VDC / 200 mA (typ.) Connectors In / Out N Female (BNC female opt.) Dimensions (HWD) in. (cm) 5.25 x 19 x 3 (13.3 x 48.3 x 7.6) Weight lb. (kg) 4 (1.8) NOTES 1. All unused ports must be terminated with 50 ohms. TWL-01 terminating resistor is available for this purpose. 2. Panel gain is measured from the input port to any output port. Gain is adjusted at the factory according to individual system requirements. 3. Tuning range and bandwidth vary depending on frequency band and system components. 4. Exact frequencies must be specified with order. 30 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2033 Rev. 6/12 TWR8, TWR16, TWR24 SERIES RECEIVER DISTRIBUTION PANELS 30 - 960 MHz 2 MULTICOUPLERS TWR8 SERIES TWR16 SERIES Telewave Receiver Distribution Additional panels may be added and bandwidth varies depending Panels are used to feed multiple at any time to increase the number on frequency band and system receivers from a common antenna, of available outputs. New panels component s. Please contac t reducing cost and tower loading, can be directly coupled to existing Te l e w a v e t o d i s c u s s y o u r while providing consistent signal panels without additional parts or requirements with a sales engineer quality, output isolation, and higher tuning. Successful multicoupling to e n s u re m a x im u m s y s te m output levels. generally requires some type of performance. A typical receiver distribution panel includes a power supply, inline low noise preamplifier, and one or two 8-way splitters all on a single 19" panel. The preamplifier provides as filtering between the receiver panel and antenna. Telewave manufactures a wide range of high quality preselector systems for transmitters and receivers. much as +18 dB system gain to Telewave receiver panels provide 8 overcome splitting and cable or 16 matched 50 ohm outputs losses. from one input, with typical 25 dB Telewave receiver panels are fully shielded, and each panel has sufficient bandwidth to cover an entire commercial or Public Safety band. Standard panels have one input, 8 or 16 outputs, and a -20 dB isolation between ports. The antenna port is tuned with a matching network to insure a balanced input. A -20 dB sample port is also provided for connection of external signal analyzers. sample port on a 7" x 19" panel. A Telewave can supply panels for 24 channel model is available for operation on +12 to +24 VDC, and 700/800 MHz only. For sites with 120 or 220/240 VAC. Other voltage limited rack space, the Telewave 1R options are available on request. A and 2R series of compact panels is battery backup on the DC input can also available with 8 or 16 channels provide uninterrupted operation in 1 rack unit (1.75" H), or up to 32 during a site power failure (charging channels on a 3.5" panel. output not supplied). Tuning range Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 31 TWDS-2020 Rev. 6/12 TWR8-, 16-, 24- SERIES 30 - 960 MHz MODEL FREQUENCY PORTS BANDWIDTH GAIN TWR8-030 30-88 MHz 8 58 MHz 0-18 dB TWR8-050 50-512 MHz 8 400 MHz 0-18 dB TWR8-150 132-174 MHz 8 42 MHz 0-18 dB TWR8-250 216-250 MHz 8 34 MHz 0-18 dB TWR8-350 300-400 MHz 8 40 MHz 0-18 dB TWR8-450 400-512 MHz 8 40 MHz 0-18 dB TWR8-760 763-824 MHz 8 40 MHz 0-12 dB TWR8-860 806-960 MHz 8 40 MHz 0-12 dB TWR16-030 30-88 MHz 16 58 MHz 0-15 dB TWR16-050 50-512 MHz 16 400 MHz 0-15 dB TWR16-150 132-174 MHz 16 42 MHz 0-15 dB TWR16-250 216-250 MHz 16 34 MHz 0-15 dB TWR16-350 300-400 MHz 16 40 MHz 0-15 dB TWR16-450 400-512 MHz 16 40 MHz 0-15 dB TWR16-760 763-824 MHz 16 40 MHz 0-8 dB TWR16-860 806-960 MHz 16 40 MHz 0-8 dB TWR24-760 763-824 MHz 24 40 MHz 0-6 dB TWR24-860 806-960 MHz 24 40 MHz 0-6 dB COMMON SPECIFICATIONS Impedance / VSWR (typ) 50 ohms / 1.3:1 Isolation RX-RX (min / typ.) 30-174 MHz: 20 dB / 25 dB 216-960 MHz: 25 dB / 30 dB Noise figure (typ) 2.5 dB Third order intercept +36 dBm Intermodulation (typ) -130 dB for -30 dBm input Sample port -20 dB Temperature range -40°C to +60°C Power requirements AC 120 VAC (std.) 220/240 VAC (opt.) DC +11.5 to +15 VDC (power reverting) +12 to +24 VDC (direct to preamp) Connectors Input - N Female Output - N or BNC Female (opt.) Dimensions (HWD) in. (cm) 7 x 19 x 3 (17.8 x 48.3 x 7.6) Weight lb. (kg) 8 / 16 / 24 ch 5.5 (2.5) / 6 (2.7) / 6.5 (2.9) NOTES 1. All unused ports must be terminated with 50 ohms. TWL-01 terminating resistor is available for this purpose. 2. Panel gain is measured from the input port to any output port. Gain is adjusted at the factory according to individual system requirements. Standard gain is 6 dB if not specified. 3. Tuning range and bandwidth vary depending on frequency band and system components. 4. Exact frequencies and system gain must be specified with order. 32 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2020 Rev. 6/12 TWR8, TWR16 -1R SERIES COMPACT RECEIVER PANELS 30 - 960 MHz 2 MULTICOUPLERS FEATURES · 25 dB TYPICAL PORT TO PORT ISOLATION · N OR BNC OUTPUT · 0.7 TO 2.5 dB TYPICAL NOISE FIGURE · MODULAR DESIGN · VHF-LOW/HIGH, UHF, 700/800/900 TRUNKING · NO TUNING REQUIRED · 1 RACK UNIT (1.75" x 19") · 24 AND 32 CHANNELS AVAILABLE IN 2 RU TWR16-450-1R Telewave Compac t Receiver New panels c an be direc tly This design is especially suited for Distribution Panels are used to c o u p l e d t o ex i s t i n g p a n e l s battery, solar panels, and thermal feed multiple receivers from a without additional par t s or generator sources. An external common antenna, reducing cost tuning. Successful multicoupling DC-DC converter allows operation a n d t o w e r l o a d i n g , w h i l e generally requires some type of from DC inputs as low as +9.5 p rov id i n g co n s i s te n t s ig n a l filtering between the receiver VDC. quality, output isolation, and higher output levels. A typical receiver distribution panel includes a power supply, panel and antenna. Telewave manufactures a wide range of high quality preselector systems for transmitters and receivers. The 1R series ships standard with an inline low noise bipolar preamplifier (except TT models). Optional items include PHEMT inline low noise preamplifier, and Telewave receiver panels use high- preamps for lower noise figure, one or two 8-way splitters all on quality splitters to provide 8 or 16 high 3rd order intercept preamps a single 19" tray. The preamplifier matched 50 ohm outputs from one for RF congested sites, redundant provides as much as +18 dB input, with typical 25 dB isolation preamps for maximum reliability system gain to overcome splitting between ports. The antenna port at remote sites, and broadband and cable losses. is tuned with a matching network p r e a m p s f o r m u l t i - b a n d Telewave 1R panels provide full to insure a balanced input. applications. performance in only 1RU. The 8 These units, with their specially channel unit can be easily field designed power supply, can be expanded to 16 channels, by powered from an AC or DC source. adding an additional 8 channel The internal DC input circuitry will s p l i t t e r. A l l r e c e i v e r p a n e l allow the external input DC voltage components are fully shielded, to vary between +11.5 VDC to +15 and each panel has sufficient VDC, while keeping the DC output bandwidth to cover an entire voltage constant. This feature commercial or Public Safet y allows the preamplifier to perform band. at its rated gain, 1 dB compression point, and 3rd order intercept point. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 33 TWDS-2021 Rev. 6/12 TWR8, TWR16 -1R SERIES 30 - 960 MHz MODEL TWR8-030-1R, RA TWR8-050-1R, RA TWR8-150-1R, RA, RTT TWR8-250-1R, RA, RTT TWR8-350-1R, RA, RTT TWR8-450-1R, RA, RTT TWR8-760-1R, RA, RTT TWR8-860-1R, RA, RTT TWR16-030-1R, RA TWR16-050-1R, RA TWR16-150-1R, RA, RTT TWR16-250-1R, RA, RTT TWR16-350-1R, RA, RTT TWR16-450-1R, RA, RTT TWR16-760-1R, RA, RTT TWR16-860-1R, RA, RTT FREQUENCY RANGE 30-88 MHz 50-512 MHz 132-174 MHz 216-250 MHz 300-400 MHz 400-512 MHz 763-824 MHz 806-960 MHz 30-88 MHz 50-512 MHz 132-174 MHz 216-250 MHz 300-400 MHz 400-512 MHz 763-824 MHz 806-960 MHz COMMON SPECIFICATIONS Impedance / VSWR (typ) Isolation port to port (min / typ.) System gain (factory adj.) 8 ch. 16 ch. Noise figure (max) Third-order intercept (typ) Intermodulation (typ) Temperature range Power requirements AC DC Connectors Dimensions (HWD) in. (cm) Weight lb. (kg) 8 ch / 16 ch PORTS 8 8 8 8 8 8 8 8 16 16 16 16 16 16 16 16 BANDWIDTH 58 MHz 400 MHz 42 MHz 42 MHz 40 MHz 40 MHz 40 MHz 40 MHz 58 MHz 400 MHz 42 MHz 42 MHz 40 MHz 40 MHz 40 MHz 40 MHz OPTIONS 1 1 1,2 1,2 1,2 1,2 1,2 1,2 1 1 1,2 1,2 1,2 1,2 1,2 1,2 50 ohms / 1.3:1 30-174 MHz: 20 dB / 25 dB 216-960 MHz: 25 dB / 30 dB 30-760 MHz: 0-18 +/-1 dB 760-960 MHz: 0-12 +/-1 dB 30-760 MHz: 0-15 +/-1 dB 760-960 MHz: 0-8 +/-1 dB 2.5 dB +36 dBm -130 dB for -30 dBm input -40°C to +60°C 120 VAC (std.) 220/240 VAC (opt.) +11.5 to +15 VDC (regulated output) +12 to +24 VDC (direct to preamp) Input - N Female Output - N or BNC Female (opt.) 1.75 x 19 x 11 (4.5 x 48.3 x 27.9) 6.5 (3.0) / 8.5 (3.9) OPTIONS: 1. RA: 0-10 dB step attenuator (std. gain 1 to 11 dB) 2. RTT: 1 amp meter movement & DC injector to power Tower Top Preamp. NOTES 1. All unused ports must be terminated with 50 ohms. TWL-01 terminating resistor is available for this purpose. 2. Panel gain is measured from the input port to any output port. Gain is adjusted at the factory according to individual system requirements. Standard gain is 6 dB if not specified. 3. Tuning range and bandwidth vary depending on frequency band and system components. 4. Exact frequencies and system gain must be specified with order. 34 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2021 Rev. 6/12 TWR24/32-2R SERIES COMPACT RECEIVER PANELS 30 - 960 MHz 2 MULTICOUPLERS FEATURES · 25 dB TYPICAL PORT TO PORT ISOLATION · N OR BNC CONNECTORS · 0.7 TO 2.5 dB TYPICAL NOISE FIGURE · MODULAR DESIGN · VHF-LOW/HIGH, UHF, 700/800/900 TRUNKING · NO TUNING REQUIRED · ONLY 2 RU (3.5" x 19") TWR32-150-2R Telewave 2R Compact Receiver generally requires some type of DC-DC converter allows operation Distribution Panels are used at filtering between the receiver from DC inputs as low as +9.5 medium to high density sites panel and antenna. Telewave VDC. to feed multiple receivers from a common antenna, reducing cost and tower loading, while providing consistent signal quality, output isolation, and higher output levels. manufactures a wide range of high quality preselector systems for transmitters and receivers. Telewave 2R Receiver Panels use high-quality splitters to provide 24 or 32 matched 50 ohm outputs The 2R series ships standard with an inline low noise bipolar preamplifier (except TT models). Optional items include PHEMT preamps for lower noise figure, high 3rd order intercept preamps A typical receiver distribution from one input, with typical 25 for RF congested sites, redundant panel includes a power supply, dB isolation bet ween por t s. preamps for maximum reliability inline low noise preamplifier, The antenna port is tuned with at remote sites, and broadband and three or four 8-way splitters a matching network to insure a p r e a m p s f o r m u l t i - b a n d all on a single 19" tray. The balanced input. applications. preamplifier provides as much as +12 dB system gain to overcome splitting and cable losses. These units, with their specially designed power supply, can be powered from an AC or DC source. Telewave 2R panels provide full The internal DC input circuitry will performance in only 2RU. All allow the external input DC voltage receiver panel components are to vary between +11.5 VDC to +15 fully shielded, and each panel VDC, while keeping the DC output has sufficient bandwidth to cover voltage constant. This feature allows an entire commercial or Public the preamplifier to perform at its Safety band. rated gain, 1 dB compression point, New panels can be directly and 3rd order intercept point. c o u p l e d t o e x i s t i n g p a n e l s This design is especially suited for w i t h o u t a d d i t i o n a l p a r t s o r battery, solar panels, and thermal tuning. Successful multicoupling generator sources. An external Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 35 TWDS-2030 Rev. 6/12 TWR24/32-2R SERIES 30 - 960 MHz MODEL FREQUENCY TWR24-030-2R 30-88 MHz TWR24-050-2R 50-512 MHz TWR24-150-2R 132-174 MHz TWR24-250-2R 216-250 MHz TWR24-350-2R 300-400 MHz TWR24-450-2R 400-512 MHz TWR24-760-2R 763-824 MHz TWR24-860-2R 806-960 MHz TWR32-030-2R 30-88 MHz TWR32-050-2R 50-512 MHz TWR32-150-2R 132-174 MHz TWR32-250-2R 216-250 MHz TWR32-350-2R 300-400 MHz TWR32-450-2R 400-512 MHz TWR32-760-2R 763-824 MHz TWR32-860-2R 806-960 MHz COMMON SPECIFICATIONS Impedance / VSWR (typ.) Isolation port to port (min / typ.) Noise figure (typ) Intermodulation (typ) Third order intercept Temperature range Power requirements AC DC Connectors Dimensions (HWD) in. (cm) Weight lb. (kg) 24 / 32 ch. PORTS 24 24 24 24 24 24 24 24 32 32 32 32 32 32 32 32 BANDWIDTH 58 MHz 400 MHz 42 MHz 34 MHz 40 MHz 40 MHz 40 MHz 40 MHz 58 MHz 400 MHz 42 MHz 34 MHz 40 MHz 40 MHz 40 MHz 40 MHz GAIN 0-12 dB 0-12 dB 0-12 dB 0-12 dB 0-12 dB 0-12 dB 0-5 dB 0-5 dB 0-12 dB 0-12 dB 0-12 dB 0-12 dB 0-12 dB 0-12 dB 0-5 dB 0-5 dB 50 ohms / 1.3:1 30-174 MHz: 20 dB / 25 dB 216-960 MHz: 25 dB / 30 dB 2.5 dB -130 dB for -30 dBm input +36 dBm -40°C to +60°C 120 VAC (std.) 220/240 VAC (opt.) +11.5 to +15 VDC (regulated output) +12 to +24 VDC (direct to preamp) Input - N Female Output - N or BNC Female (opt.) 3.5 x 19 x 11 (8.9 x 48.3 x 27.9) 11 (5.0) / 13 (5.9) NOTES 1. All unused ports must be terminated with 50 ohms. TWL-01 terminating resistor is available for this purpose. 2. Panel gain is measured from the input port to any output port. Gain is adjusted at the factory according to individual system requirements. Standard gain is 6 dB if not specified. 3. Tuning range and bandwidth vary depending on frequency band and system components. 4. Exact frequencies and system gain must be specified with order. 36 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2030 Rev. 6/12 PS- SERIES RECEIVER POWER SPLITTERS 10 - 1000 MHz 2 MULTICOUPLERS Telewave Receiver Power Splitters provide 2 to 8 matched 50 ohm receiver outputs from one input. The antenna port is tuned with a matching network to insure a balanced input. Since the input signal is split evenly between all ports, the available signal at each output port will be 3 to 9 dB below the input. For this reason, a preamp is generally used to compensate for coupler and cable losses. These rugged, compact splitters are commonly used in RX multicouplers, and are not intended to be used with transmitters. Telewave makes a full line of transmitter power dividers with 500 watt power capability for this purpose. MODEL PORTS FREQUENCY PS-302 2 33-50 MHz PS-702 2 72-88 MHz PS-1502 2 132-174 MHz PS-1504 4 148-174 MHz PS-3302 2 320-390 MHz PS-4502 2 400-512 MHz PS-4504 4 400-512 MHz PS-4508 8 400-512 MHz PS-5002 2 10-1000 MHz PS-5004 4 10-1000 MHz PS-5008 8 30-512 MHz PS-7602 2 763-824 MHz PS-7604 4 763-824 MHz PS-7608 8 763-824 MHz PS-8602 2 806-960 MHz PS-8604 4 806-960 MHz PS-8608 8 806-960 MHz COMMON SPECIFICATIONS Impedance / VSWR (typ.) Isolation (min / typ.) Connectors Dimensions 2-way in. (cm) 4-way in. (cm) 8-way in. (cm) PS-5002 in. (cm) PS-5004 in. (cm) Coupling loss 2 / 4 / 8-port Insertion loss (typ.) 2 / 4 / 8-port Weight lb. (kg) 2 / 4 / 8-port BANDWIDTH 8 MHz 16 MHz 26 MHz 26 MHz 30 MHz 40 MHz 40 MHz 40 MHz 1000 MHz 1000 MHz 500 MHz 30 MHz 40 MHz 40 MHz 30 MHz 40 MHz 40 MHz STD. TUNE 38-46 MHz 72-88 MHz 148-174 MHz 148-174 MHz 350-380 MHz 450-470 MHz 450-470 MHz 450-470 MHz N/A N/A N/A 793-824 MHz 793-824 MHz 793-824 MHz 806-824 MHz 806-824 MHz 806-824 MHz 50 ohms / 1.3:1 20 dB / 25 dB Input - N Female Output - N or BNC Female (opt.) 1.25 x 2.25 x 1.5 (3.2 x 5.7 x 3.8) 1.75 x 4.25 x 2.5 (4.5 x 10.8 x 6.4) 8 x 5.25 x 1 (20.3 x 13.3 x 2.5) 2.75 x 2 x 0.75 (7 x 5.1 x 1.9) 3.5 x 3 x 0.75 (8.9 x 7.6 x 1.9) 3 / 6 / 9 dB 0.2 / 0.4 / 0.6 dB 1 (0.45) / 2 (0.9) / 3 (1.4) Note: Splitters are normally factory tuned as indicated. Other ranges must be specified with order. Terminate unused ports with 50 ohms. Two-Way Splitter Four-Way Splitter Eight-Way Splitter Wideband Splitter - PS-5002 Wideband Splitter - PS-5004 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 37 TWDS-2013 Rev. 5/12 30 - 960 MHz TLA SERIES LOW NOISE BIPOLAR INLINE PREAMPLIFIERS FEATURES · 50 OHM INPUT/OUTPUT · OVER-VOLTAGE/POLARITY PROTECTION · VERSATILE MOUNTING OPTIONS · HIGH THIRD ORDER INTERCEPT · RESISTANT TO INPUT OVERLOAD Signal input Telewave TLA Series in-line preamplifiers use surface-mount bipolar devices to amplify low level RF signals by up to 34 dB. The primary application of these preamplifiers is to improve the noise figure of a receiver system. Preamps compensate for splitter insertion loss or losses from long coax cable runs, and increase signal levels to spectrum analyzers or other test equipment. Each preamplifier is housed in a rugged, custom made, RF-tight aluminum enclosure. The DC input is reverse polarity protected, and equipped with a high-pass filter to eliminate RFI. Preamplifiers are tuned to customer specified center frequencies. Signal output DC input COMMON SPECIFICATIONS Impedance / VSWR (max) Noise figure (typ) Gain (factory adjusted) (Standard gain is 16 dB +/- 1 dB) 1 dB compression (typ) 3rd order intercept (typ) Power requirements Transient protection Temperature range Enclosure Hardware Connectors Dimensions (HWD) in. (cm) Footprint in. (cm) Net weight oz (g) Shipping weight lb. (kg) 50 ohms / 1.3:1 2.5 dB 30-88 MHz: +8 to +34 dB 132-512 MHz: +6 to +28 dB 760-960 MHz: +6 to +21 dB +25 dBm +35 dBm +12 to +24 VDC, 170 mA 20 kV / 1 s 0°C to +40°C Gold or clear alodine Stainless steel N Female (SMA, BNC opt.) 1.3 x 2.25 x 2.0 (3.3 x 5.7 x 5.1) 3.25 x 2.25 (8.3 x 5.7) 3.8 (108) 1 (0.45) MODEL FREQUENCY BANDWIDTH TLA50-12 30-88 MHz 60 MHz TLA150-12 TLA220-12 132-174 MHz 216-250 MHz 50 MHz 50 MHz TLA330-12 320-390 MHz 70 MHz TLA450-12 400-512 MHz 112 MHz TLA760-12 763-824 MHz 50 MHz TLA860-12 806-960 MHz 50 MHz NOTE: These preamplifiers are for receiver use only. They are not designed to accept transmitter power levels. 38 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2002 Rev. 5/12 MULTICOUPLERS TGA SERIES PHEMT PREAMPLIFIERS 132 - 960 MHz 2 FEATURES · VERY LOW NOISE · 50 OHM INPUT/OUTPUT · OVER-VOLTAGE / POLARITY PROTECTION · VERSATILE MOUNTING OPTIONS · COMMON PORT INDUCTANCE Telewave TGA Series in-line preamplifiers utilize PHEMT devices to amplify low-level RF signals by up to 18 dB. The primary application of these preamplifiers is to improve the noise figure of a receiver system. Each preamplifier is housed in a Preamps compensate for splitter rugged, custom made, RF-tight insertion loss or losses from long aluminum enclosure. The DC input coax cable runs, and increase signal is reverse polarity protected, and levels to spectrum analyzers or equipped with a high-pass filter to other test equipment. eliminate RFI. DC input NOTE: These preamplifiers are for receiver use only. They are not designed to accept transmitter power levels. MODEL TGA150-12 Frequency range 132-174 MHz Bandwidth (typ) 5 MHz Noise figure (typ) 0.4 dB Gain (typ) +18 dB COMMON SPECIFICATIONS Impedance / VSWR (max) 1 dB compression (typ) 3rd order intercept (typ) Power requirements Transient protection Temperature range Enclosure Hardware Connectors Dimensions (HWD) in. (cm) Net weight oz (g) Shipping weight lb. (kg) TGA220-12 220-250 MHz 6 MHz 0.5 dB +18 dB TGA450-12 400-512 MHz 60 MHz 0.5 dB +17 dB TGA750-12 763-824 MHz 100 MHz 0.7 dB +13 dB TGA860-12 806-960 MHz 100 MHz 0.7 dB +13 dB 50 ohms / 1.3:1 +12 dBm +26 dBm +9 to +18 VDC, 40 mA 40 kV / 1 s 0° to +40°C Irridited aluminum Stainless steel N Female (SMA, BNC opt.) Teflon dielectric, gold pin 1.5 x 2.5 x 0.7 (3.8 x 6.4 x 1.8) 5.4 (154) 1 (0.45) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 39 TWDS-2003 Rev. 5/12 TWR1 SERIES RACK MOUNT PHEMT PREAMPLIFIERS 132 - 960 MHz The TWR-1 Series of Rack Mount PHEMT Preamplifiers provide up to +18 dB of user-controllable gain in a receiver system. These preamps provide extra gain to compensate for loss of signal from tower extension, receiver filtering, or long cable runs. Each unit consists of a low-noise PHEMT preamplifier, a 10 dB rotary step attenuator, and a regulated switching power supply mounted on a 19-inch single rack-unit aluminum panel. Primary input power is 120 or 220 VAC, and DC backup requires +11 to +15 VDC. The DC input is reverse polarity protected, and equipped with a high-pass filter to eliminate RFI. Standard gain is +1 to +11 dB. Any range between +1 to +11 and +8 to +18 dB may be specified, depending on frequency. NOTE: These preamplifiers are for receiver use only. They are not designed to accept transmitter power levels. MODEL TWR1-150 Frequency range 132-174 MHz Bandwidth (typ) 5 MHz Noise figure (typ) 0.4 dB Gain range (typ) +1 to +11 dB +8 to +18 dB COMMON SPECIFICATIONS Impedance / VSWR (typ) 1 db compression (typ) 3rd order intercept (typ) Transient protection Temperature range Power requirements AC DC Current drain (typ) Dimensions (HWD) in. (cm) Connectors Net weight lb. (kg) Shipping weight lb. (kg) TWR1-220 200-250 MHz 6 MHz 0.5 dB +1 to +11 dB +8 to +18 dB TWR1-450 400-512 MHz 50 MHz 0.5 dB +1 to +11 dB +7 to +17 dB TWR1-760 763-824 MHz 100 MHz 0.7 dB +1 to +11 dB +4 to +14 dB 50 ohms / 1.3:1 +12 dBm +26 dBm 40 kV / 1 s 0°C to +40°C 120 VAC (std.) or 220 VAC (opt.) +11.5 to +15 VDC or +9 to +18 VDC 50 mA 1.75 x 19 x 5 (4.5 x 48.3 x 12.7) N Female 2.5 (1.1) 3.5 (1.6) TWR1-860 806-960 MHz 100 MHz 0.7 dB +1 to +11 dB +4 to +14 dB 40 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2004 Rev. 5/12 MULTICOUPLERS TOWER TOP PREAMPLIFIERS WITH INTEGRATED PRESELECTORS 300 - 901 MHz 2 Telewave Integrated Tower Top Preamplifier systems recover lowlevel signals from long or high loss transmission lines and optimize system performance. The Telewave system allows single, multi-band and/or multi-window operation in the 300-400, 400-512, 793-824, and 806-901 MHz receiver bands. The RF preamplifier is designed with two PHEMT devices in a redundant hybrid configuration. A single device failure causes a 6 dB reduction in gain, but the amplifier continues to operate with stable impedance. This provides high operational reliability. Very low loss input circuits provide the best possible noise figure. DC surge and reverse voltage protection is provided. The preselector filter systems incorporate combline, cavity and multi-window technologies. Each filter is custom designed to operate in the most adverse RF environments. The base power supply provides DC coupling and decoupling to the transmission line and connection to the receiver distribution system. TTPA-3548 Tower Top Preamp/Preselector DC current levels are monitored with a built-in metering panel. The enclosure is fully weathersealed, compliant with NEMA 4. ELECTRICAL SPECIFICATIONS Frequency ranges System gain (max, single band) 3rd order intercept (typ) Noise figure (typ) VSWR Lightning protection Power requirements Temperature range MECHANICAL SPECIFICATIONS Tower box TTPA-4586 TTPA-8626 TTPA-8690 Base supply Finish Tower box Base supply Connectors 300-512, 793-824, 896-901 MHz 17 dB (factory adjusted) +40 dB 0.8 dB 1.3:1 Impulse supressor (Polyphaser) +15 VDC / 280 mA (+12 VDC opt.) -40°C to +70°C Dimensions (HWD) in. (cm) 24 x 20 x 12 (61 x 51 x 31) 16 x 16 x 6 (41 x 41 x 15) 16 x 16 x 10 (41 x 41 x 25) 19 x 3.5 x 7.25 (48 x 9 x 14) NEMA 4 - Gray polyester powder coat Grained aluminum N Female Weight lb. (kg) 39 (17.7) 39 (17.7) 39 (17.7) 4.7 (2.1) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 41 TWDS-2022 Rev. 5/12 455 - 512 MHz TTPA-4544 TOWER TOP PREAMPLIFIER / PRESELECTOR Telewave Integrated Tower Top Preamplifier systems recover lowlevel signals from long or high loss transmission lines and optimize system performance. The Telewave system enables single or multiwindow operation in the 450-512 MHz receiver bands. The RF preamplifier is designed with two PHEMT devices in a redundant hybrid configuration. A single device failure causes a 6 dB reduction in gain, but the amplifier continues to operate with stable impedance. This provides high operational reliability. Very low loss input circuits provide the best possible noise figure. DC surge and reverse voltage protection is provided. The preselector filter systems incorporate combline, cavity and multi-window technologies. TTPA-4544 Towertop Preamplifier Each filter is custom designed to DC current levels are monitored operate in the most adverse RF with a built-in metering panel. environments. The enclosure is fully weather- The base power supply provides sealed, compliant with NEMA 4. DC coupling and decoupling to the transmission line and connection to the receiver distribution system. ELECTRICAL SPECIFICATIONS Frequency ranges (MHz) System gain (single band) Noise figure (typ) 3rd order intercept (typ) Power requirements VSWR Lightning protection Temperature range MECHANICAL SPECIFICATIONS Dimensions Tower box (HWD) in. (cm) Base supply Weight Tower box lb. (kg) Base supply Finish Tower box Base supply Connectors 455-460, 465-470, 470-512 17 dB (factory adjusted) 0.8 dB +40 dB +15 VDC / 280 mA (+12 VDC opt.) 1.3:1 Impulse supressor (Polyphaser) -40°C to +70°C 20 x 16 x 11.5 (50.8 x 40.6 x 29.2) 19 x 3.5 x 7.25 (48.3 x 8.9 x 18.4) 39 (17.7) 4.7 (2.1) NEMA 4 - Gray polyester powder coat Grained aluminum N Female 42 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2009 Rev. 5/12 TTPA-8626, 8644, 8648 TOWER TOP PREAMPLIFIER / PRESELECTOR 806 - 960 MHz 2 MULTICOUPLERS TTPA-8648 TTPA-8626 TPCP-8648 Filter Type: Pass Cavity 0 10 20 30 40 50 60 70 80 ELECTRICAL SPECIFICATIONS Frequency range 806-960 MHz System gain (typ) 15 dB to 17 dB Preselector Bandwidth (MHz) 5, 6, 10, 15, 20 Noise figure Bipolar 2.7 dB PHEMT 1.2 dB 3rd order intercept Point +35 dBm +33 dBm Redundancy Hybrid combined redundant pair with tower top bypass relay DC Input Voltage +15 VDC / 280 mA (+12 VDC opt.) Input VSWR <1.3:1 Lightning protection Impulse suppressor type Temperature range -40°C to +70°C MECHANICAL SPECIFICATIONS Dimensions HWD in. (cm) 10, 15, 20 MHz BW 16 x 8 x 6 (40.6 x 30.3 x 15.2) 5, 6 MHz BW 16 x 16 x 8 (40.6 x 40.6 x 30.3) Weight: Tower box lb. (kg) 39 (17.7) Connector type N-Type, gold center pin Finish: Tower box NEMA 4 - Gray polyester powder coat Optional sampling port available, connected to input of preselector for tower-top effective sensitivity measurements. Requires extra coax run. Attenuation (dB) 798 803 808 813 818 823 828 Frequency (MHz) TPCP-8626 Filter Type: Combline 0 10 20 30 40 50 60 70 80 -60 -40 -20 Fo +20 +40 +60 Frequency (MHz) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2014 Rev. 12/12 43 TTBS-4586 TOWER TOP BASE POWER SUPPLY The Telewave TTBS-4586 Base The Base Power Supply accepts A front panel step attenuator is Power Supply provides up to 1 AC or optional DC input, or both, also available. amp of regulated DC power for any depending on system requirements. Telewave tower mounted preamp. A built-in DC-DC converter allows The TTBS-4586 is designed around a custom power supply, which supplies +15 VDC to the preamp DC input up to 75 VDC. The panel requires a 3.5" x 19" rack space, and includes a 1 amp current meter. via the coax cable. Voltage is The optional TCMA-300 current coupled to the transmission line monitor and alarm panel provides by a Polyphaser GX series impulse adjustable high and low current suppressor, which incorporates a trip points with form "C" contact DC power injector. closure and LED status alarm. ELECTRICAL SPECIFICATIONS AC input voltage DC output voltage (to tower unit) Stand by dc input voltage (opt) Input / output VSWR Lightning protection Temperature range MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Weight lb. (kg) RF Connectors Finish Optional front panel 100-240 VAC, 50-60 Hz / 0.4 A +15 VDC / 1A +/- 9-18, 18-36, or 36-75 VDC <1.3:1 Impulse suppressor, 20 kA -40°C to +70°C 3.5 x 19 x 7.25 (8.9 x 48.3 x 18.4) 4.7 (2.1) N-female Grained aluminum, clear alodine Black paint 44 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2032 Rev. 5/12 TPCP-1342C / TPCP-1343C COMPACT VHF AIRBAND PRESELECTORS 118 - 136 MHz 2 MULTICOUPLERS TPCP-1342C The TPCP-1342C and TPCP-1343C offer high performance in a compact design for the VHF Air band. A custom extruded 4-inch square cavity allows horizontal mounting on a standard 19-inch rack, with rack height of 5.25". The TPCP-1342C uses two cavities to provide typical attenuation of better than 50 dB at +/- 5 MHz. The TPCP-1343C uses three cavities, and provides typical attenuation of better than 70 dB. Attenuation (dB) TPCP-1343C TPCP-1342C TYPICAL RESPONSE CURVES TPCP-1343C SPECIFICATIONS Frequency range Bandpass (typ) Attenuation at +/- 5 MHz (typ) Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) Mounting Finish Weight lb. (kg) TPCP-1342C TPCP-1343C 118-136 MHz 700 KHz 1.5 MHz 45 dB 70 dB 2.0 dB 2.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 2 / 4" 3 / 4" N Female, UHF (opt.) 5.25 x 19 x 17 (13.3 x 48.3 x 43.2) 19" rack mount Alodine / Gray acrylic enamel 13 (5.9) 16 (7.3) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com Frequency (MHz) All specifications subject to change without notice TWDS-2016 Rev. 10/12 45 118 - 136 MHz TPCP-1344C / TPCP-1344CM COMPACT VHF AIRBAND PRESELECTOR The TPCP-1344C/CM offers high performance in a compact design for the 118-136 MHz VHF airband. The TPCP-1344C provides a bandpass of 2 MHz or less, with typical isolation of better than 50 dB at +/- 5 MHz, and insertion loss of 1.5 dB or less. A custom extruded 4-inch square cavity allows horizontal mounting on a standard 19-inch rack, with rack height of 5.25"(C) and 4"(CM). The "C" model mounts in a 19-inch EIA rack, and the "CM" has adjustable mounting tabs for installation in a cabinet. TPCP-1344CM Attenuation (dB) 0 10 20 30 40 50 60 70 125.0 TPCP-1344C TYPICAL RESPONSE CURVES 130.0 Frequency (MHz) 135.0 SPECIFICATIONS - TPCP-1344C / CM Frequency range 118-136 MHz Bandpass (max) 2 MHz Attenuation at +/- 5 MHz Fc (min) 50 dB Insertion loss (typ) 1.5 dB Power input (max) 350 watts Impedance (nom) / VSWR (max) 50 ohms / 1.5:1 Temperature range -30°C to +70°C Number of cavities / size 4 / 4" Connectors N Female, UHF (opt.) Dimensions (HWD) in. (cm) C 5.25 x 19 x 18 (13.3 x 48.3 x 45.7) (Tuners fully extended) CM 4 x 19 x 18 (10.2 x 48.3 x 45.7) Mounting C 19" rack mount CM 19" cabinet mount Finish Alodine / Gray acrylic enamel Weight lb. (kg) 19.5 (8.9) 46 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2029 Rev. 10/12 TPCP-1442C / TPCP-1443C COMPACT VHF PRESELECTORS 135 - 151 MHz 2 MULTICOUPLERS TPCP-1442C TPCP-1443C The TPCP-1442C and TPCP-1443C offer high performance in a compact design for the 135-151 MHz VHF band. A custom extruded 4-inch square cavity allows horizontal mounting on a standard 19-inch rack, with rack height of 5.25". The TPCP-1442C uses two cavities to provide typical attenuation of better than 50 dB at +/- 5 MHz, and insertion loss of 1.0 dB or less. The TPCP-1443C uses three cavities, and provides typical attenuation of better than 70 dB, and insertion loss of 1.5 dB or less. SPECIFICATIONS Frequency range Bandpass (typ) Attenuation at +/- 5 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) Mounting Finish Weight lb. (kg) 135.0 135.0 TPCP-1442C TPCP-1443C 135-151 MHz 700 KHz 1.5 MHz 50 dB (min) 70 dB (min) 1.0 dB 2.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 2 / 4" 3 / 4" N Female, UHF (opt.) 5.25 x 19 x 15 (13.3 x 48.3 x 38.1) 19" rack mount Alodine / Gray acrylic enamel 12 (5.4) 15 (6.8) Attenuation (dB) TPCP-1442C 140.0 TYPICAL RESPONSE CURVES TPCP-1443C 140.0 Frequency (MHz) 145.0 145.0 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 47 TWDS-2027 Rev. 10/12 135 - 151 MHz TPCP-1444C / TPCP-1444CM COMPACT VHF PRESELECTOR The TPCP-1444C/CM offers high performance in a compact design for the 135-151 MHz VHF band. The TPCP-1444C provides a bandpass of 2 MHz or less, with typical isolation of better than 50 dB at +/- 5 MHz, and insertion loss of 1.5 dB or less. A custom extruded 4-inch square cavity allows horizontal mounting on a standard 19-inch rack, with rack height of 5.25" (C) and 4" (CM). The "C" model mounts in a 19-inch EIA rack, and the "CM" has adjustable mounting tabs for installation in a cabinet. TPCP-1444CM Attenuation (dB) TPCP-1444C 0 10 20 30 40 50 60 70 135.0 TYPICAL RESPONSE CURVES 140.0 Frequency (MHz) 145.0 SPECIFICATIONS - TPCP-1444C / CM Frequency range 135-151 MHz Bandpass (max) 2 MHz Attenuation at +/- 5 MHz Fc (min) 50 dB Insertion loss (typ) 1.5 dB Power input (max) 350 watts Impedance (nom) / VSWR (max) 50 ohms / 1.5:1 Temperature range -30°C to +70°C Number of cavities / size 4 / 4" Connectors N Female, UHF (opt.) Dimensions (HWD) in. (cm) C 5.25 x 19 x 18 (13.3 x 48.3 x 45.7) (Tuners fully extended) CM 4 x 19 x 18 (10.2 x 48.3 x 45.7) Mounting C 19" rack mount CM 19" cabinet mount Finish Alodine / Gray acrylic enamel Weight lb. (kg) 19.5 (8.9) 48 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2010 Rev. 10/12 MULTICOUPLERS TPCP-1446C COMPACT VHF PRESELECTOR The TPCP-1446C of fers high performance in a compact design for the 135-151 MHz VHF band. Six square, pass-reject cavities provide greater than 80 dB attenuation at +/- 5 MHz, with a bandpass of 2.2 MHz or less, and insertion loss of 2.5 dB or less. The custom-extruded 4" cavities allow horizontal rack mounting on a standard 19" rack, with rack height of only 8.75". 135 - 151 MHz 2 Attenuation (dB) 0 10 20 30 40 50 60 70 80 135.0 TYPICAL RESPONSE CURVES 140.0 Frequency (MHz) 145.0 SPECIFICATIONS - TPCP-1446C Frequency range Bandpass (max) Attenuation at +/- 5 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) (Tuners fully extended) Mounting Finish Weight lb. (kg) 135-151 MHz 2.2 MHz 80 dB 2.5 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 6 / 4" N Female, UHF (opt.) 8.75 x 19 x 18 (22.2 x 48.3 x 45.7) 19" rack mount Alodine / Gray acrylic enamel 36.5 (16.6) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 49 TWDS-2011 Rev. 10/12 TPCP-1414, -1514, -1614, -1714 COMPACT VHF PRESELECTORS The TPCP-1414, -1514, -1614, and -1714 are ver y compac t, 4-cavity preselectors for the VHF band from 140-180 MHz. These preselectors produce a minimum of 45 dB attenuation, and are ideal for limited space applications, including portable repeaters and mobile installations. Simple mounting to any flat surface allows maximum flexibility. Each model covers a 10 MHz tuning range. 140 - 180 MHz TPCP-1414 140-150 MHz TPCP-1514 150-160 MHz TPCP-1614 160-170 MHz TPCP-1714 170-180 MHz SPECIFICATIONS - TPCP-1414, 1514, 1614, 1714 Frequency range 1414 140-150 MHz 1514 150-160 MHz 1614 160-170 MHz 1714 170-180 MHz Bandpass (typ) 2 MHz Attenuation at +/- 5 MHz 45 dB Insertion loss (typ) 1.5 dB Power input (max) 50 watts Impedance (nom) / VSWR (max) 50 ohms / 1.5:1 Temperature range -30°C to +70°C Number of cavities / size 4 / 1" Connectors BNC female, N female (opt) Dimensions (HWD) in. (cm) 1.25 x 4 x 5 (3.2 x 10.2 x 12.7) Mounting Flat surface Finish Black enamel Net weight lb. (kg) 1 (0.45) Shipping weight lb. (kg) 2 (0.9) Attenuation (dB) TYPICAL RESPONSE CURVES 0 10 20 30 40 50 60 70 80 142.5 155.0 Frequency (MHz) 167.5 Appearance of current production models may vary from picture. 50 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2015 Rev. 10/13 TPCP-1542C / TPCP-1543C COMPACT VHF PRESELECTORS 148 - 174 MHz 2 MULTICOUPLERS TPCP-1542C TPCP-1543C The TPCP-1542C and TPCP-1543C offer high performance in a compact design for the 148-174 MHz VHF band. Custom-extruded 4-inch square cavities allow horizontal mounting on a standard 19-inch rack, with rack height of 5.25". The TPCP-1542C uses two cavities to provide typical attenuation of better than 50 dB at +/- 5 MHz, and insertion loss of 1.0 dB or less. The TPCP-1543C uses three cavities, and provides typical attenuation of better than 70 dB, and insertion loss of 1.5 dB or less. SPECIFICATIONS Frequency range Bandpass (typ) Attenuation at +/- 5 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) Mounting Finish Weight lb. (kg) 155.0 155.0 TPCP-1542C TPCP-1543C 148-174 MHz 700 KHz 1.5 MHz 50 dB (min) 70 dB (min) 1.0 dB 2.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 2 / 4" 3 / 4" N Female, UHF (opt.) 5.25 x 19 x 14 (38.7 x 48.3 x 35.6) 19" rack mount Alodine / Gray acrylic enamel 11 (5) 14 (6.4) Attenuation (dB) TPCP-1542C 160.0 TYPICAL RESPONSE CURVES TPCP-1543C 160.0 Frequency (MHz) 165.0 165.0 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 51 TWDS-2028 Rev. 10/12 148 - 174 MHz TPCP-1544C / TPCP-1544CM COMPACT VHF PRESELECTOR The TPCP-1544C/CM offers high performance in a compact design for the 148-174 MHz VHF band. The TPCP-1544C provides a bandpass of 2 MHz or less, with typical isolation of better than 50 dB at +/- 5 MHz, and insertion loss of 1.5 dB or less. A custom extruded 4" square cavity allows horizontal mounting on a standard 19" rack, with rack height of 5.25" (C) and 4" (CM). The "C" model mounts in a 19" EIA rack, and the "CM" has adjustable mounting tabs for installation in a cabinet. TPCP-1544CM Attenuation (dB) TPCP-1544C 0 10 20 30 40 50 60 70 155.0 TYPICAL RESPONSE CURVES 160.0 Frequency (MHz) 165.0 SPECIFICATIONS - TPCP-1544C / CM Frequency range 148-174 MHz Bandpass (max) 2 MHz Attenuation at +/- 5 MHz Fc (min) 50 dB Insertion loss (typ) 1.5 dB Power input (max) 350 watts Impedance (nom) / VSWR (max) 50 ohms / 1.5:1 Temperature range -30°C to +70°C Number of cavities / size 4 / 4" Connectors N Female, UHF (opt.) Dimensions (HWD) in. (cm) C 5.25 x 19 x 15 (13.3 x 48.3 x 38.1) (Tuners fully extended) CM 4 x 19 x 15 (10.2 x 48.3 x 38.1) Mounting C 19" rack mount CM 19" cabinet mount Finish Alodine / Gray acrylic enamel Weight lb. (kg) 18.25 (8.3) 52 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2005 Rev. 10/12 MULTICOUPLERS TPCP-1546C COMPACT VHF PRESELECTOR The TPCP-1546C of fers high performance in a compact design for the 148-174 MHz VHF band. Six square, pass-reject cavities provide greater than 80 dB attenuation at +/- 5 MHz, with a bandpass of 2.2 MHz or less, and insertion loss of 2.5 dB or less. The custom-extruded 4-inch cavities allow horizontal rack mounting on a standard 19" rack, with rack height of only 8.75". 148 - 174 MHz 2 Attenuation (dB) 0 10 20 30 40 50 60 70 80 155.0 TYPICAL RESPONSE CURVES 160.0 Frequency (MHz) 165.0 SPECIFICATIONS - TPCP-1546C Frequency range Bandpass (max) Attenuation at +/- 5 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) (Tuners fully extended) Mounting Finish Weight lb. (kg) 148-174 MHz 2.2 MHz 80 dB 2.5 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 6 / 4" N Female, UHF (opt.) 8.75 x 19 x 15 (22.2 x 48.3 x 38.1) 19" rack mount Alodine / Gray acrylic enamel 36.5 (16.6) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 53 TWDS-2006 Rev. 10/12 148 - 174 MHz TPCP-1554, -1556 BANDPASS PRESELECTOR Telewave TPCP-1554 and TPCP- All units are factory tuned to 1556 preselectors are specially customer-supplied frequencies designed for use with master and no further adjustment should receive systems to insure rejection be necessary. Field re-tuning or of external noise sources. These adjustment of insertion loss can be bandpass preselectors provide accomplished quickly if needed. optimum receiver desense protection when installed between a receiver multicoupler and the antenna. In addition, their high power capability allows these units to be used as sideband filters on the outputs of transmitters or transmitter combiners. Attenuation (dB) TYPICAL FILTER RESPONSE CURVES TPCP-1554 0 10 20 30 40 50 60 70 80 -3 -2 -1 Fo +1 +2 +3 Frequency (MHz) Bandpass preselectors reject all signals outside a selected pass window, and are often preferred at congested sites. These bandpass filters consist of 4 or 6 series-connected cavities, and are available in a wide range of pass bandwidths. Each model features "sharp-skirt" selectivity with minimum insertion loss. For optimum performance, these bandpass filters are custom tailored to meet individual requirements. Multiple-window configurations can be provided when more than one pass band is required. Heavy duty materials are used throughout these bandpass filters to insure top performance and long life, and RG214 Mil-Spec cable is used for interconnections. Temperature stability is maintained from -30 to +70°C by the use of temperature compensators, and threaded invar rod. Tuners are silver plated and sliding contacts are made with beryllium copper fingerstock. All models are 19" rack-mountable, and come with N Female connectors. TPCP-1554 TPCP-1556 SPECIFICATIONS Frequency range Bandpass (typ) Attenuation at +/- 5 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) Attenuation (dB) TPCP-1556 0 10 20 30 40 50 60 70 80 -6 -4 -2 Fo +2 +4 +6 Frequency (MHz) TPCP-1554 TPCP-1556 148-174 MHz 700 KHz or less 1.3 MHz or less 40 dB 80 dB 1.5 dB 2.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 4 / 5" 6 / 5" N Female, UHF (opt.) 28 x 19 x 10.5 (71.1 x 48.3 x 26.7) 19" rack mount Alodine / Gray acrylic enamel 20 (9.1) 29 (13.2) 23 (10.4) 32 (14.5) 54 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2018 Rev. 10/12 TPCP-2244, -2246 BANDPASS PRESELECTORS 200 - 300 MHz 2 MULTICOUPLERS Telewave TPCP-2244 and TPCP- All units are factory tuned to 2246 preselectors are specially customer-supplied frequencies designed for use with master and no further adjustment should receive systems to insure rejection be necessary. Field retuning or of external noise sources. These adjustment of insertion loss can be bandpass preselectors provide accomplished quickly if needed. optimum receiver desense protection when installed between a receiver multicoupler and the antenna. In addition, their high power capability allows these units to be used as sideband filters on the outputs of transmitters or TPCP-2244 transmitter combiners. Attenuation (dB) TYPICAL FILTER RESPONSE TPCP-2244 0 10 20 30 40 50 60 70 80 Bandpass preselectors reject all signals outside a selected pass window, and are often preferred at congested sites. 247.5 249.5 251.5 253.5 255.5 257.5 259.5 Frequency (MHz) These bandpass filters consist of 4 or 6 series-connected cavities, and are available in a wide range of pass bandwidths. Each model features "sharp-skirt" selectivity with minimum insertion loss. For optimum performance, these bandpass filters are custom tailored to meet individual requirements. Multiple-window configurations can be provided when more than one pass band is required. Heavy duty materials are used throughout these bandpass filters to insure top performance and long life, and RG214 Mil-Spec cable is used for interconnections. Temperature stability is maintained from -30 to +70°C by the use of temperature compensators, and threaded invar rod. Tuners are silver plated and sliding contacts are made with beryllium copper fingerstock. All models are 19" rack-mountable, and come with N Female connectors. TPCP-2246 SPECIFICATIONS Frequency range Bandpass (typ) Attenuation at +/- 5 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. cm Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) TPCP-2244 TPCP-2246 200-300 MHz 2 MHz or less 4 MHz or less 50 dB 80 dB 1.5 dB 2.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 4 / 4" 6 / 4" N Female, UHF (opt.) 5.25 x 19 x 12 10.5 x 19 x 12 13.3 x 48.3 x 30.5 26.7 x 48.3 x 30.5 19" rack mount Alodine / Gray acrylic enamel 20 (9.1) 29 (13.2) 23 (10.4) 32 (14.5) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 55 TWDS-2031 Rev. 10/12 300 - 400 MHz TPCP-3544, -3546, -3548 UHF BANDPASS PRESELECTOR Telewave TPCP-3544, 3546, and 3548 UHF Bandpass Preselectors are specially designed for use with master receive systems, to ensure rejection of external noise sources. These bandpass preselectors provide optimum receiver desense protection when installed between the receiver multicoupler and the antenna. Their high power capability also allows these units to be used as sideband filters on the outputs of transmitters or transmitter combiners. Bandpass preselectors reject all signals outside a selected pass window, and are often preferred at congested sites. These bandpass filters consist of 4, 6, or 8 series-connected cavities, and are available in a wide range of pass bandwidths. Each model features "sharp-skirt" selectivity with minimum insertion loss. For optimum performance, these bandpass filters are custom tailored to meet individual requirements. Multiple-window configurations can be provided when more than one pass band is required. Heavy duty materials are used throughout the bandpass filters to insure top performance and long life, and RG-214 Mil-Spec cable is used for interconnections. Temperature stability is maintained from -30 to +70°C by the use of temperature compensators, and threaded invar rod. Tuners are silver plated and sliding contacts are made with beryllium copper fingerstock. All models are 19" rack-mountable, and come with N Female connectors. All units are factory tuned to customer-supplied frequencies and no further adjustment should be necessary. Field re-tuning or adjustment of insertion loss can be accomplished quickly if needed. TPCP-3546 Attenuation (dB) TYPICAL FILTER RESPONSE CURVES 0 0 TPCP-3544 TPCP-3546 10 2 TPCP-3548 20 4 30 6 40 8 50 10 TPCP-3544 60 12 70 14 TPCP-3546 TPCP-3548 -8 -6 -4 -2 Fo +2 +4 +6 +8 -4 -3 -2 -1 Fo +1 +2 +3 +4 Frequency (MHz) SPECIFICATIONS Frequency range Bandpass (typ) Attenuation (+/- 5 MHz) Insertion loss (typ) Power input (max) Impedance / VSWR (max) Temperature range Number of cavities Connectors Dimensions (HWD) in. cm Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) TPCP-3544 TPCP-3546 TPCP-3548 300-400 MHz 2 MHz 4 MHz 4 MHz 50 dB 55 dB 80 dB 1.5 dB 2.0 dB 3.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 4 / 4" 6 / 4" 8 / 4" N Female, UHF (opt.) 5.25x19 x15 7 x19 x15 8.75x19x15 13 x 48 x 38 18 x 48 x 38 22 x 48 x 38 19" rack mount Alodine / Gray acrylic enamel 12 (5.5) 19 (8.6) 24 (10.9) 16 (7.3) 28 (12.7) 33 (15) 56 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2007 Rev. 10/12 TPCP-4542 BANDPASS PRESELECTOR 400 - 512 MHz 2 MULTICOUPLERS The Telewave TPCP-4542 UHF receiver preselector is specially designed for use in master antenna receive systems, to insure rejection of external noise sources. This bandpass preselector provides optimum protection against desense and adjacent channel interference when installed between the receiver multicoupler and antenna. High power capability also allows these units to be used as sideband filters on the outputs of transmitters or transmitter combiners. Bandpass preselectors reject all signals outside a selected pass window, and are often preferred at congested sites. Heavy-duty materials are used throughout this bandpass filter to insure top performance and long service. RG-214 Mil-Spec cable is used for the interconnect, and temperature stability is maintained by the use of a threaded invar tuning rod. Tuners are all silver-plated, and sliding contacts are manufactured from beryllium copper fingerstock. This unit is 19" rack mounted, and comes with N Female connectors standard. All units are factory tuned to customer-supplied frequencies and no further adjustment should be necessary. Field re-tuning or adjustment of insertion loss can be accomplished quickly if needed. Attenuation (dB) TPCP-4542 459 MHz at 2.0 dB IL 0 10 20 30 40 50 60 70 80 TWPC-4504-2 Cavity Response 0 10 0.5 dB 20 0.75 dB 30 1.0 dB 40 2.0 dB 50 60 4.0 dB 70 80 453 455 457 459 461 463 465 -6 -4 -2 Fo +2 +4 +6 Frequency (MHz) SPECIFICATIONS - TPCP-4542 Frequency range Bandpass (max) Attenuation at +/- 5 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) 400-512 MHz 1 MHz or less 35 dB 1.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 2 / 4" N Female 5.25 x 19 x 10.5 (13.3 x 48.3 x 26.5) 19" rack mount Alodine / Gray acrylic enamel 5 (2.3) 8 (3.6) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 57 TWDS-2019 Rev. 10/12 400 - 512 MHz TPCP-4544, -4546, -4548 UHF BANDPASS PRESELECTOR Telewave TPCP-4544, 4546, and 4548 UHF Bandpass Preselectors are specially designed for use with master receive systems, to ensure rejection of external noise sources. These bandpass preselectors provide optimum receiver desense protection when installed between the receiver multicoupler and the antenna. Their high power capability also allows these units to be used as sideband filters on the outputs of transmitters or transmitter combiners. Bandpass preselectors reject all signals outside a selected pass window, and are often preferred at congested sites. These bandpass filters consist of 4, 6, or 8 series-connected cavities, and are available in a wide range of pass bandwidths. Each model features "sharp-skirt" selectivity with minimum insertion loss. For optimum performance, these bandpass filters are custom tailored to meet individual requirements. Multiple-window configurations can be provided when more than one pass band is required. Heavy duty materials are used throughout the bandpass filters to insure top performance and long life, and RG-214 Mil-Spec cable is used for interconnections. Temperature stability is maintained from -30 to +70°C by the use of temperature compensators, and threaded invar rod. Tuners are silver plated and sliding contacts are made with beryllium copper fingerstock. All models are 19" rack-mountable, and come with N Female connectors. All units are factory tuned to customer-supplied frequencies and no further adjustment should be necessary. Field re-tuning or adjustment of insertion loss can be accomplished quickly if needed. TPCP-4546 Attenuation (dB) TYPICAL FILTER RESPONSE CURVES 0 0 TPCP-4544 TPCP-4546 10 2 TPCP-4548 20 4 30 6 40 8 50 10 TPCP-4544 60 12 70 14 TPCP-4546 TPCP-4548 -8 -6 -4 -2 Fo +2 +4 +6 +8 -4 -3 -2 -1 Fo +1 +2 +3 +4 Frequency (MHz) SPECIFICATIONS Frequency range Bandpass (typ) Attenuation (+/- 5 MHz) Insertion loss (typ) Power input (max) Impedance / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. cm Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) TPCP-4544 TPCP-4546 TPCP-4548 400-512 MHz 2 MHz 4 MHz 4 MHz 50 dB 55 dB 80 dB 1.5 dB 2.0 dB 3.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 4 / 4" 6 / 4" 8 / 4" N Female, UHF (opt.) 5.25x19 x10.5 7 x19 x10.5 8.75x19x10.5 13 x 48 x 27 18 x 48 x 27 22 x 48 x 27 19" rack mount Alodine / Gray acrylic enamel 10 (4.5) 16 (7.3) 20 (9.1) 14 (6.4) 24 (11) 28 (12.7) 58 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2023 Rev. 10/12 TPCP-45215 / 46215 / 45215-2 UHF COMBLINE PRESELECTORS 450 - 470 MHz TPCP-45215 455-460 MHz TPCP-46215 465-470 MHz TPCP-45215-2 455-470 MHz 2 MULTICOUPLERS Telewave TPCP-45215/46215 single and TPCP-45215-2 dual window combline preselectors are specially designed for use with master receive systems, to optimize performance on UHF repeater frequencies, and provide excellent rejection of external noise sources. These combline filters provide maximum protection from receiver desense when installed between the receiver multicoupler and the antenna. The 45215 and 46215 combline filters have a bandpass of 4 MHz, and consist of a series of resonators in a compact enclosure, mounted on a standard 5.25" x 19" panel. The 45215-2 provides two 4 MHz windows on a 10.5" x 19" panel. These units feature "sharp-skirt" selectivity with minimum insertion loss in single or dual configuration. All units are pre-tuned to customer-specified frequencies before shipment to provide optimum performance, and no further adjustment should be necessary. Telewave combline filters offer the ultimate in repeater system performance, maximizing coverage and providing protection against receiver desensitization at congested sites. With new narrowband channel assignments, proper filtering is even more critical. The TPCP-45215 series allows operators of high-density UHF systems to take advantage of new technology, and enhance the performance of existing systems. Attenuation (dB) Attenuation (dB) TPCP-45215, 46215 Single Window Combline 0 10 20 30 40 50 60 70 80 462.50 467.50 Frequency (MHz) 472.50 TYPICAL FILTER RESPONSE CURVES TPCP-45215-2 Dual Window Combline Preselector 0 10 20 30 40 50 60 70 80 447.50 462.50 477.50 Frequency (MHz) SPECIFICATIONS Configuration Frequency range (MHz) Bandpass (typ) Attenuation (typ) Insertion loss (typ) Impedance / VSWR (max) Temperature range Connectors Dimensions (HWD) in. cm Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) TPCP-45125 TPCP-46215 TPCP-45215-2 SINGLE WINDOW DUAL WINDOW 455-460 465-470 455-460/465-470 2 MHz 4 MHz 4 + 4 MHz > 35 dB at +/- 3MHz from Fc 2.0 dB 50 ohms / 1.5:1 -30°C to +70°C N Female 5.25 x 19 x 10 13.3 x 48.3 x 25.4 10.5 x 19 x 10 26.7 x 48.3 x 25.4 19" rack mount Clear alodine / black paint 12 (5.5) 24 (10.9 ) 14 (6.4) 29 (13.2) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 59 TWDS-2001 Rev. 10/12 TPCP-4514 COMPACT UHF PRESELECTOR The TPCP-4514 is an ultra-compact, 4-cavity preselector for the UHF band from 450-470 MHz. This preselector produces a minimum of 30 dB attenuation, and is ideal for limited space applications, including portable repeaters and mobile installations. Simple mounting to any flat surface allows maximum flexibility. The TPCP-4514 covers a 20 MHz tuning range. 450 - 470 MHz SPECIFICATIONS - TPCP-4514 Frequency range Bandpass (typ) Attenuation at +/- 10 MHz Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) max (including connectors, tuners and mounting tabs Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) 450-470 MHz 4 MHz 30 dB 2.0 dB 50 watts 50 ohms / 1.5:1 -30°C to +70°C 4 / 1" N female, BNC female (opt) 1.1 x 4.9 x 4 (2.8 x 12.4 x 10.2) Flat surface Black enamel 1 (0.45) 2 (0.9) Attenuation (dB) TYPICAL RESPONSE CURVES 0 10 20 30 40 50 60 70 80 450 460 470 Frequency (MHz) Appearance of current production models may vary from picture. 60 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2008 Rev. 10/13 TPCP-8642, TPCP-8644 BANDPASS PRESELECTORS 806 - 960 MHz 2 MULTICOUPLERS Telewave TPCP-8642 and 8644 fingerstock. All models are 19" Bandpass Preselectors are specially rack-mountable, and come with N designed for use with 800 MHz Female connectors. receiver systems to insure rejection of external noise sources. These bandpass preselectors provide optimum receiver desense protection when installed between the receiver multicoupler and the antenna. Their high power capability allows these units to be used as sideband filters on the outputs TPCP-8642 of transmitters or transmitter combiners. Attenuation (dB) TYPICAL RESPONSE CURVES Preselector TPCP-8642 0 10 20 30 40 50 60 70 -15 -10 -5 Fo +5 +10 +15 Frequency (MHz) Bandpass preselectors reject all signals outside a selected pass window, and are often preferred at congested sites. These bandpass filters are available with up to a 5 MHz pass bandwidth, and they consist of 2 or 4 seriesconnected cavities. Each model features "sharp-skirt" selectivity with minimum insertion loss. For optimum performance, these bandpass filters are custom tailored to meet individual requirements. Multiple-window configurations can be provided when more than one pass band is required. All units are factory tuned to customersupplied frequencies and no further adjustment should be necessary. Heavy duty materials are used throughout these bandpass filters to insure top performance and long life, and only RG214 Mil-Spec cable is used for interconnections. Temperature stability is maintained from -30 to +70°C by the use of temperature compensators, and threaded invar rod. Tuners are silver plated and sliding contacts are made with beryllium copper TPCP-8644 SPECIFICATIONS Frequency range Bandpass (typ) Attenuation (+/- 45 from Fc) Insertion loss (typ) Power input (max) Impedance / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. cm Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) Attenuation (dB) Preselector TPCP-8644 0 10 20 30 40 50 60 70 -30 -20 -10 Fo +10 +20 +30 Frequency (MHz) TPCP-8642 TPCP-8644 806-960 MHz 2 MHz or less 5 MHz or less 90 dB 0.5 dB 1.0 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 2 / 4" 4 / 4" N Female 5.25 x 19 x 10.5 5.25 x 19 x 10.5 13.3 x 48.3 x 26.7 13.3 x 48.3 x 26.7 19" rack mount Alodine / Gray acrylic enamel 8 (3.6) 10 (4.5) 12 (5.5) 14 (6.4) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 61 TWDS-2025 Rev. 10/12 806 - 960 MHz TTPP-8642 BANDPASS / BANDREJECT PRESELECTOR The Telewave Model TTPP-8642 Bandpass-Bandreject Preselector is designed for use with master receive systems to insure rejection of external noise sources. The TTPP-8642 utilizes an exclusive "side-by-side" coupling technique which produces a 5 MHz bandpass, and a reject characteristic at 45 MHz above the passband. This provides optimum receiver protection when installed between a receiver multicoupler and the antenna. High power capability also allows these units to be used as sideband filters on the outputs of transmitters or transmitter combiners. These filters cover a 5 MHz pass bandwidth, and they consist of 2 series-connected cavities. They feature "sharp-skirt" selectivity with minimum insertion loss. All units are factory tuned to customersupplied frequencies and no further adjustment should be necessary. Heavy duty materials are used throughout these bandpass filters to insure top performance and long life, and Mil-Spec semi-rigid cable is used for interconnections. Temperature stability is maintained from -30 to +70°C by the use of temperature compensators, and threaded invar rod. Tuners are silver plated and sliding contacts are made with beryllium copper fingerstock. All models are 19" rack-mountable, and come with N Female connectors. Attenuation (dB) TYPICAL RESPONSE CURVE 0 10 20 30 40 50 60 70 -10 Fo +10 +20 +30 +40 +50 Frequency (MHz) SPECIFICATIONS - TTPP-8642 Frequency range Bandpass (max) Attenuation (+45 from Fo) Insertion loss (typ) Power input (max) Impedance (nom) / VSWR (max) Temperature range Number of cavities / size Connectors Dimensions (HWD) in. (cm) Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) 806-960 MHz 5 MHz or less 90 dB 0.5 dB 350 watts 50 ohms / 1.5:1 -30°C to +70°C 2 / 4" N Female 5.25 x 19 x 10.5 (13.3 x 48.3 x 26.5) 19" rack mount Alodine / Gray acrylic enamel 8 (3.6) 12 (5.5) 62 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-2012 Rev. 10/12 TPCP-8626, TPCF-8926 COMBLINE PRESELECTORS 806 - 890 MHz TPCP-8626 806-821 MHz TPCP-8626B 824-849 MHz TPCF-8926 870-890 MHz TPCF-8926B 870-890 MHz 2 MULTICOUPLERS The TPCP-8626 and TPCF-8926 Combline Preselector filters are specially designed for use in 800 MHz master receive systems, allowing system designers to accommodate multiple systems while ensuring rejection of external noise sources. These preselectors and sideband filters provide maximum desense protection for receiver front ends when installed between the multicoupler or transmitter and antenna. Combline filters feature "sharp skirt" selectivity with very low insertion loss (see below). Each filter is factory tuned and tested on customer supplied frequencies prior to shipment. The 8626/8926 filter series is available with pass bandwidths of 10, 15, and 20 MHz, and each unit consists of a series of 6 resonators in a compact 13" x 2" x 4.5" package. These filters are typically supplied on a 19" panel for rack mounting, and other options are available on request. Attenuation (dB) TPCP-8626 TYPICAL FILTER RESPONSE TPCP-8626 0 TPCF-8926 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 -30 -20 -10 Fo +10 +20 +30 -15 -10 -5 Fo +5 +10 +15 Frequency (MHz) SPECIFICATIONS Frequency range (MHz) Bandpass (typ) Attenuation (+/- 45 from Fc) Insertion loss (typ) Power input (max) Impedance / VSWR (max) Temperature range Number of cavities Connectors Dimensions (HWD) in (cm) Mounting Finish Net weight lb. (kg) Shipping weight lb. (kg) TPCP-8626 806-821 MHz 15 MHz N/A TPCP-8626B TPCF-8926 824-849 MHz 870-890 MHz 10 MHz 20 MHz 85 dB 0.35 dB N/A 500 watts 50 ohms / 1.25:1 -30 to +60°C 6 N Female 3.5 x 19 x 5 (8.9 x 48.3 x 12.7) 19" rack mount Clear alodine 4 (1.8) 8 (3.6) TPCF-8926B 870-890 MHz 10 MHz 500 watts Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 63 TWDS-2024 Rev. 10/12 3 POWER MONITORING 3 POWER MONITORING Broadband Wattmeters Telewave Broadband Wattmeters are known worldwide for quality, durability, and convenience. A single meter covers 2-200 MHz or 20-1000 MHz and 1-500 watts with no plugin elements or band switching. Power Monitors RF power monitors produce a calibrated DC voltage proportional to an RF signal between 30 and 960 MHz. They are available as single and dual-direction devices with very low insertion loss. Alarm Panels Power monitoring and alarm panels continuously monitor the output of up to 12 transmitters and 2 antennas. Multiple measurements are switch selectable including VSWR and FWD/REV power. Relay contact closures indicate out of range conditions. 2 - 200 MHz MODEL 44L1, L1P BROADBAND RF WATTMETER FEATURES · REQUIRES NO ELEMENTS OR "SLUGS" · NO BAND SWITCHING · MEASURES 1 TO 500 WATTS · 5 POWER RANGES · 5 WATT FULL SCALE RANGE · COVERS 2 - 200 MHz · MEASURES FORWARD AND REFLECTED POWER · -40 dB RF SAMPLING PORT · SHOCK-MOUNTED METER · LOW TEMPERATURE OPERATION · QUICK-CHANGE CONNECTORS · LIGHT WEIGHT: 3 LBS The Telewave Model 44L1/L1P RF Wattmeter is a compact, versatile instrument used for direct measurement of forward and reflected RF power in a coaxial transmission line under any load conditions. Wide band capability and dynamic range allows operation without elements, inserts, or bandswitching. The 20 microamp taut-band meter movement is shock mounted in a rugged, diecast housing, making this instrument ideal for mobile radio installation in aircraft or vehicles, as well as base stations. Model 44L1P includes an RF sampling port, with an output 40 dB below the total transmission line level, for frequency measurement, signal injection, or spectral analysis. MODEL 44L1P BACK CARRY CASE (OPTIONAL) 66 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-3003 Rev. 9/12 POWER MONITORING MODEL 44L1, L1P This wideband instrument covers 2 to 200 MHz with a power range of 1 to 500 watts. The meter movement can be turned off for protection when not in use. A leather carrying strap is provided for easy portability. The use of a taut-band meter movement allows operation in cold temperatures. to drive the 20 µA taut band meter. Forward and reflected power can be directly measured by rotating the FWD-REV switch. VSWR (Voltage Standing Wave Ratio) is easily determined by comparing these measurements and using the convenient chart on the back of the instrument. The RF sample port on Model 44L1P samples a low level of RF power as it passes through the instrument. This bi-directional port is accessed via a BNC connector located on the side of the meter. It allows injection of a signal into the device under test, or can be used for spectrum analysis and frequency measurements without affecting operation of the meter. Five power scales are provided. The 500 watt scale will test most high powered transmitters, while the 5 watt scale makes it simple to tune low powered portables. The excellent stability of this unit and the ability to switch it from one power range to another to check the calibration eliminates the need for a secondary standard to verify calibration. The Model 44L1/L1P utilizes a set of precision directional detectors which sample forward and reverse CW power flow in a specially engineered section of transmission line. The sampled current is scaled 2 - 200 MHz 3 SPECIFICATIONS Frequency range Full scale power ranges Impedance, primary line VSWR (max) Accuracy (at 80% of full scale) RF sampling port (44L1P) Connectors (input/output) (Quick-Change standard) Sample port Dimensions (HWD) in. mm Weight lbs (kg) 2-200 MHz 5, 15, 50, 150 and 500 watts 50 ohms nominal 1.1:1 +/- 7% with N connectors only -40 dB +/-2 dB below total power (forward + reverse) N Female standard UHF, DIN, TNC, BNC optional BNC Female 6.625 x 4 x 3.25 168.3 x 101.6 x 82.6 3 (1.36) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 67 TWDS-3003 Rev. 9/12 20 - 1000 MHz MODEL 44A, AP BROADBAND RF WATTMETER FEATURES · REQUIRES NO ELEMENTS OR "SLUGS" · NO BAND SWITCHING · MEASURES 1 TO 500 WATTS · 5 POWER RANGES · 5 WATT FULL SCALE RANGE · COVERS 20 - 1000 MHz · MEASURES FORWARD AND REFLECTED POWER · -40 dB RF SAMPLING PORT · SHOCK-MOUNTED METER · LOW TEMPERATURE OPERATION · QUICK-CHANGE CONNECTORS · LIGHT WEIGHT: 3 LBS The Telewave Model 44A/AP RF Wattmeter is a compact, versatile instrument used for direct measurement of forward and reflected RF power in a coaxial transmission line under any load conditions. Wide band capability and dynamic range allows operation without elements, inserts, or bandswitching. The 20 microamp taut-band meter movement is shock mounted in a rugged, diecast housing, making this instrument ideal for mobile radio installation in aircraft or vehicles, as well as base stations. Model 44AP includes an RF sampling port, with an output 40 dB below the total transmission line level, for frequency measurement, signal injection, or spectral analysis. MODEL 44AP BACK CARRY CASE (OPTIONAL) 68 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-3002 Rev. 9/12 MODEL 44A, AP 20 - 1000 MHz 3 POWER MONITORING This wideband instrument covers CW power flow in a specially 20 to 1000 MHz with a power engineered section of transmission range of 1 to 500 watts. The line. The sampled current is scaled meter movement can be turned to drive the 20 µA taut band meter. off for protection when not in use. Forward and reflected power can A leather carrying strap is provided be directly measured by rotating for easy portability. The use of a the F WD - RE V switch. VSWR taut-band meter movement allows (Voltage Standing Wave Ratio) is operation in cold temperatures. easily determined by comparing The RF sample port on Model 44AP samples a low level of RF power as it passes through the instrument. This these measurements and using the convenient chart on the back of the instrument. bi-directional port is accessed via a Five power scales are provided. BNC connector located on the side The 500 watt scale will test most of the meter. It allows injection of a high powered transmitters, while signal into the device under test, or the 5 watt scale makes it simple to can be used for spectrum analysis tune low powered portables. The and frequency measurements excellent stability of this unit and without affecting operation of the the ability to switch it from one meter. power range to another to check The Model 44A/AP utilizes a set of precision directional detectors which sample forward and reverse the calibration eliminates the need for a secondary standard to verify calibration. SPECIFICATIONS Frequency range Full scale power ranges Impedance, primary line VSWR (max) RF sampling port (44AP) Connectors (input/output) (Quick-Change standard) Sample port Dimensions (HWD) in. mm Weight lbs (kg) 20-1000 MHz 5, 15, 50, 150 and 500 watts 50 ohms nominal 1.1:1 -40 dB +/-2 dB below total power (forward + reverse) N Female standard UHF, DIN, TNC, BNC optional BNC-female 6.625 x 4 x 3.25 168.3 x 101.6 x 82.6 3 (1.36) +/-6% with correction 20 MHz 150 MHz METER ACCURACY Type N connectors +/-6% (UHF connectors not specified) 1000 MHz Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 69 TWDS-3002 Rev. 9/12 30 - 960 MHz RF POWER MONITORS PM-1A, PM-2A SERIES Telewave RF Power Monitors are band. One or two RCA connectors single or dual-direction devices provide access to the proportional which produce a DC voltage DC output, which is coupled to the proportional to an RF signal between meter panel with a simple shielded 30 and 960 MHz, depending on audio-type cable. model. These devices exhibit extremely low insertion loss, and are designed to be placed in the transmission line permanently, allowing continuous monitoring of Standard RF connectors are N Female. Any combination of N, SMA, or UHF, Male or Female are available on request. forward and reflected power. Each power monitor is used for Note: Center frequency or desired one transmitter within a specified bandwidth. Voltage trimmers allow band coverage must be specified with order. each unit to be quickly recalibrated for a new frequency within the same PM-1A MODEL TYPE FREQUENCY BANDWIDTH* PM-1A-50 Single Direction 30-88 MHz 20 MHz PM-1A-90 Single Direction 87.5-108 MHz 20 MHz PM-1A-150 Single Direction 118-230 MHz 50 MHz PM-1A-300 Single Direction 200-400 MHz 50 MHz PM-1A-450 Single Direction 380-512 MHz 50 MHz PM-1A-760 Single Direction 700-869 MHz 50 MHz PM-1A-900 Single Direction 806-960 MHz 50 MHz PM-2A-50 Dual Direction 30-88 MHz 20 MHz PM-2A-90 Dual Direction 87.5-108 MHz 20 MHz PM-2A-150 Dual Direction 118-230 MHz 50 MHz PM-2A-300 Dual Direction 200-400 MHz 50 MHz PM-2A-450 Dual Direction 380-512 MHz 50 MHz PM-2A-760 Dual Direction 700-869 MHz 50 MHz PM-2A-900 Dual Direction 806-960 MHz 50 MHz SPECIFICATIONS Input power range 5-1000 watts Impedance (typ.) 50 ohms VSWR (max) 1.1:1 Insertion loss (typ) 0.1 dB Dimensions (HWD) in. (cm) 1.375 x 2.25 x 1.25 (3.5 x 5.7 x 3.2) Weight lb. (kg) 0.5 (0.2) RF connectors Any combination of N, SMA, or UHF Male/Female (specify types) DC connectors RCA-F standard, BNC-F or SMA (optional) PM-2A *Bandwidth is the approximate maximum range over which a useful range of voltages are available without retuning. 70 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-3015 Rev. 10/11 PM1C1S RF POWER MONITOR / ALARM PANEL 30 - 960 MHz 3 POWER MONITORING The Telewave PM1C1S is a singlechannel, single antenna automatic alarm panel for low transmit power and high VSWR, featuring "true VSWR" circuitry and a built-in power monitor. The 2RU panel (3.5" x 19") mounts in any standard rack or inside most base station cabinets, and can be powered directly from 120 VAC or 12 VDC. Whenever a low transmitter power condition is sensed by the PM1C1S, a latched relay closure occurs and a red light on the front panel turns on. Both normally-open and normally-closed relay contacts are provided. A high VSWR condition is indicated by a second latched relay and light. These contacts can be used to remotely activate light, speakers, or other alarm systems. The relays and lights are reset by means of a front panel RESET button. The panel also operates as an inline power monitor, measuring both forward and reverse RF power, with readings displayed on a 3.5-inch meter. A PM-2A power monitor for the appropriate frequency band is included, attached to the rear panel. The PM1C1S has 2 meter scale options: 0-250 watts, or 0-400 watts. The meter scale and frequency band must be specified with the order. FREQUENCY RANGE 30-88 MHz 87.5-108 MHz 118-512 MHz 760-960 MHz BANDWIDTH 20 MHz 20 MHz 50 MHz 40 MHz The frequency range is determined by the integrated power monitor. Bandwidth is the approximate maximum range over which a useful range of voltages are available without retuning. SPECIFICATIONS Power scales FWD REV VSWR alarm range Low power alarm range Delay timing range Relay contacts, closure Relay contacts, ratings Temperature range Power requirements Dimensions (HWD) in. (cm) Weight lbs (kg) 0-250 watts or 0-400 watts 0-25 watts or 0-120 watts 2.0:1 +25% / -10% 5 watts to full scale 0.1 to 1 second N/O and N/C 3A - AC or DC -20°C to +60°C 120 VAC / 4 W or +12 VDC / 2 W 3.5 x 19 x 4 (8.9 x 48.3 x 10.2) 3.5 (1.6) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 71 TWDS-3006 Rev. 8/09 30 - 960 MHz PM5C1S RF POWER MONITOR / ALARM PANEL The Telewave PM5C1S is an automatic alarm panel featuring "true VSWR" circuitry. With optional PM-1A or PM-2A power monitors, this panel monitors the power output of up to 5 transmitters for low power, and provides a high VSWR alarm for one antenna. The 3RU (5.25" x 19") panel mounts in any standard rack or inside most The PM5C1S has 2 meter scale base station cabinets, and can be options: 0-250 watts, or 0-400 powered directly from 120VAC or watts. The meter scale must be 12VDC. specified with the order. Whenever a low transmitter power condition is sensed by the PM5C1S on one of the five channels, a latched relay closure occurs for the appropriate channel and a red light turns on at the front of the panel. Normally open and normally-closed relay contacts are provided for each individual channel. FREQUENCY RANGE 30-88 MHz BANDWIDTH 20 MHz A high antenna VSWR condition is accurately sensed at all power levels and indicated by a sixth latched relay and light. These contacts can be used to remotely activate lights, speakers, or other alarm systems. The relays and lights are reset by means of a front panel RESET button or by momentarily grounding the RESET input connection located on the rear of the unit. The panel also operates as an inline power monitor, measuring both forward and reverse RF power of up to five transmitters plus a sixth channel for single antenna VSWR, with all readings displayed on a 3.5-inch meter. Up to 6 power monitors (not included) for the appropriate frequency band are required. 87.5-108 MHz 20 MHz 118-512 MHz 50 MHz 760-960 MHz 40 MHz The frequency range is determined by the associated power monitors. Bandwidth is the approximate maximum range over which a useful range of voltages are available without retuning. SPECIFICATIONS Power scales FWD REV VSWR alarm range Low power alarm range Delay timing range Relay contacts, closure Relay contacts, ratings Temperature range Power requirements Dimensions (HWD) in. (cm) 0-250 watts or 0-400 watts 0-25 watts or 0-120 watts 2.0:1 +25% / -10% 5 watts to full scale 0.1 to 1 second N/O and N/C 3A - AC or DC -20°C to +60°C 120 VAC / 8 W or +12 VDC / 3.5 W 5.25 x 19 x 3.25 (13.3 x 48.3 x 8.3) Weight lbs (kg) 4 (1.8) 72 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-3007 Rev. 6/13 PM10C2S1C RF POWER MONITOR PANEL 30 - 960 MHz 3 POWER MONITORING The Telewave PM10C2S1C is a 1RU, compact RF power monitor panel, capable of monitoring up to ten transmitters and two antennas with optional PM-1A or PM-2A power monitors. This unit fits in 1.75" x 19", preserving valuable rack space for other equipment. The PM10C2S1C greatly simplifies procedures for monitoring the output of transmitters, and the condition of transmission lines and antennas. Ten remote transmitter keying switches are provided, and a simple two wire hook-up (RF shielded or twisted pair) from the keying circuit of each transmitter to the screw terminals located on the rear of the wattmeter panel completes the connections. A floating ground required by certain transmitters is provided for each keyer. VSWR calculations can be made when appropriate dual-direction power monitors are installed. The FWD / REV switch on the front panel quickly displays forward and reflected power for the transmitter or antenna circuits. Up to 10 power monitors (not included) for the appropriate frequency band(s) are required. FREQUENCY RANGE BANDWIDTH 30-88 MHz 20 MHz 87.5-108 MHz 20 MHz 118-512 MHz 50 MHz 760-960 MHz 40 MHz The frequency range is determined by the associated power monitors. Bandwidth is the approximate maximum range over which a useful range of voltages are available without retuning. The power monitor panel is not frequency dependent, and power monitors for multiple bands can be used with a single panel. No power supply is required for the meter panel. SPECIFICATIONS Power scales FWD REV Monitor inputs Input connectors Temperature range Dimensions (HWD) in. (cm) Weight lbs (kg) 0-400 watts 0-120 watts 12 FWD, 12 REV RCA-Female -20°C to +60°C 1.75 x 19 x 5 (4.5 x 48.3 x 12.7) 2 (0.9) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 73 TWDS-3016 Rev. 2/10 4 ISOLATORS AND LOADS 4 ISOLATORS AND LOADS Coaxial Loads RF loads provide stable constant impedance termination for receiver panels and transmitters up to 300 watts. Dry loads can be operated in any position, and offer extremely low VSWR and Quick-Change connectors. Ferrite Isolators Telewave isolators provide isolation between transmitters by controlling the directional flow of RF energy. Power which is coupled into an antenna system from a nearby transmitter can be circulated into a load before it contributes to intermodulation. High Power Isolators High power isolators handle up to 400 watts of power. These rugged devices are custom-built for each application and extensively tested in the Telewave manufacturing plant. Intermodulation Suppression IM Panels are self-contained devices which generally include a single or dual isolator, low-pass filter, and output termination load. Each panel is designed to provide plug-and-play installation and can solve many difficult interference problems. TWL-01, 35, 60 COAXIAL RF TERMINATIONS Telewave compact coaxial loads offer extremely low VSWR. All loads are machined to withstand any bench or field use, and their power rating provides substantial overload protection. Unlike oilfilled loads, these dry coaxial loads can be operated in any position. Connectors have a silver-plated center conductor, except TWL-01 which uses a gold-plated pin. TWL-01 is designed as a port termination for receiver splitters w i t h N, SM A , U H F, o r BN C female outputs. TWL-35 and TWL-60 feature recessed male connectors for reduced size and ease of use. Applications include hybrids, isolators, power monitors, wattmeters, and coaxial port terminations. FEATURES · EXTREMELY LOW VSWR · CW POWER RATINGS TO 60 WATTS · DRY LOAD · BROAD FREQUENCY RANGE · RUGGED CONSTRUCTION · N, BNC, OR UHF MALE CONNECTOR (Specify connector type) 0 - 2500 MHz TWL-01 TWL-35 TWL-60 100 mW 35 W 60 W 0-2500 MHz 0-1000 MHz 0-1000 MHz TWL-60 TWL-35 TWL-01 SPECIFICATIONS TWL-01* TWL-35 TWL-60 Frequency range 0-2500 MHz 0-1000 MHz 0-1000 MHz Maximum avg. CW power 250 mW 35 W 60 W Max VSWR (N connector) 1.22:1 1.05:1 1.05:1 Impedance (nom.) 50 ohms (nominal) Temperature rating 100% of rated power at 40°C · 50% of rated power at 95°C 50% overload rating 2 Minutes Connectors N / SMA / UHF / BNC Male N or UHF Male N or UHF Male Dimensions (dia. x H) in (cm) 0.8 x 0.97 (2.0 x 2.5) 1.6 x 1.4 (4.1 x 3.6) 1.6 x 2.375 (4.1 x 6.0) Weight lb. (kg) 0.07 (0.03) 0.25 (0.11) 0.5 (0.2) *Used to terminate unused ports on receiver splitters and panels. 76 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-3004 Rev. 8/09 ISOLATORS & TERMINATIONS TWL-50, 75, 100, 100HS COAXIAL RF TERMINATIONS Telewave Coaxial Loads feature extremely low VSWR and excellent stability. Applications include hybrids, isolators, power monitors, wattmeters, and coax line terminations. Telewave loads are custom machined to withstand bench or field use. The conservative power rating provides substantial overload protection. Unlike liquid dielectric loads, Telewave dr y coaxial terminations can be operated in any position. All connectors have gold-plated center pins for maximum conductivity. Quick-Change connectors are standard on these loads, allowing easy configuration for any application. Specify connector type(s) when ordering. For added flexibility, straight or elbow-type male-male adapters are available. FEATURES · EXTREMELY LOW VSWR · CW POWER RATINGS TO 150 WATTS · DRY DIELECTRIC · BROAD FREQUENCY RANGE · RUGGED CONSTRUCTION · QUICK-CHANGE CONNECTORS 0 - 2500 MHz TWL-50 TWL-75 TWL-100 TWL-100HS 50 W 75 W 100 W 100 W 0-2500 MHz 4 0-2500 MHz 0-2500 MHz 0-2500 MHz TWL-50 TWL-75 TWL-100 COMMON SPECIFICATIONS Frequency range Nominal impedance Temperature rating 50% overload rating MODEL Maximum CW avg power Max VSWR (N connector) Dimensions (H x dia.) in. (incl. connector) cm Weight lb. (kg) Connectors 0 - 2500 MHz 50 ohms 40°C max ambient - 100% of rated power 95°C max ambient - 50% of rated power 2 minutes TWL-50 TWL-75 50 watts 75 watts 1.1:1 1.05:1 6 x 1.75 8 x 2.25 15.2 x 4.5 20.3 x 5.7 1 (0.5) 2.1 (1) Quick-Change N Female (std.) UHF, TNC, BNC, 7-16 DIN (opt.) TWL-100HS TWL-100 TWL-100HS 100 watts 100 watts 1.05:1 1.05:1 7.25 x 3.375 7 H x 2.75 W x 2.75 D 18.4 x 8.6 17.8 x 7 x 7 4 (1.8) 2.7 (1.2) Quick-Change N Male (std.) UHF, TNC, BNC, 7-16 DIN (opt.) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 77 TWDS-3005 Rev. 10/06 TWL-150, TWL-300 HIGH POWER TERMINATIONS The Telewave TWL-150 Bench Te l e w ave l o a d s a r e c u s to m Load is ideal as a general purpose machined to withstand bench or medium power termination. It is field use. The conservative power perfectly suited for terminating the rating provides substantial overload Model 44A Broadband wattmeter, protection. Unlike liquid dielectric or any other application requiring a load s, Telewave dr y coa x ial very low VSWR, 50 ohm termination. terminations can be operated in any The carry handle and rugged position. construction allow convenient field use. All connectors have gold-plated center pins for maximum The Telewave TWL-300 Bench Load conduc tiv it y. Q uic k- Chang e is our highest power standard connectors are standard on these termination. This load is designed loads, allowing easy configuration for testing high power amplifiers, for any applic ation. Specif y or applications requiring longer connector type(s) when ordering. duty cycles. For added flexibility, straight or Telewave coaxial loads feature elbow-type male-male adapters are extremely low VSWR and excellent available. stability. Applications include hybrids, isolators, power monitors, wattmeters, and coax line terminations. 0 - 2500 MHz TWL-150 150 W 0-2500 MHz TWL-300 300 W 0-1000 MHz TWL-150 TWL-300 SPECIFICATIONS Frequency range Power input (max) Impedance (nom) VSWR (max) Return loss (typ.) Temperature rating 50% overload rating Connector Dimensions (HWD) in. (cm) Footprint in. (cm) Weight lb. (kg) Finish TWL-150 TWL-300 0 - 2500 MHz 0 - 1000 MHz 150 watts 300 watts 50 ohms 1.05:1 1.25:1 32 dB 18 dB 100% of rated power at 40°C · 50% of rated power at 95°C 2 Minutes Quick-Change N Female (std.), UHF, TNC, BNC, 7-16 DIN 6.5 x 3.5 x 6.5 (16.5 x 8.9 x 16.5) 8.1 x 2.5 x 9.5 (20.6 x 6.4 x 24.1) 7 x 4 (17.8 x 10.2) 9.5 x 4.6 (24.1 x 11.7) 4.8 (2.2) 13 (5.9) High Temp Black 78 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-3001 Rev. 5/12 ISOLATORS & TERMINATIONS T-1030 / T-1060 FERRITE ISOLATORS 66 - 108 MHz 4 Telewave Single and Dual Ferrite Isolators prevent intermodulation, and protect transmitters from high VSWR or mistuned filtering devices by providing a constant 50 ohm impedance. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 50 watts of power, with several different load options. All Telewave isolators include one or two removeable 35 watt loads in the basic configuration. Typical tuning range is up to ± 3 MHz from the original center frequency, and typical isolation is 35 dB for single, and 70 dB for dual. NOTE: Isolators have limited bandwidth and tuning range. Each isolator is manufactured for a specific range and tuned to a specific frequency. Please specify the exact desired operating frequency and special load requirements with the order. CAVITY-MOUNT ISOLATOR T-1030 SINGLE ISOLATOR T-1060 DUAL ISOLATOR BENEFITS Under adverse conditions, the isolator performs several critical functions: Broken Antenna, Damaged Cable, High VSWR Intermodulation All of these conditions will cause large amounts of When RF energy from a strong nearby signal source power to be reflected down the transmission line enters a transmitter via the antenna, mixing with the toward the transmitter. The circulatory property of the primary transmitter frequency often occurs, resulting isolator will direct this energy to the load port, and in the radiation of new, undesired signals. The isolator protect the transmitter. The load on the isolator must antenna port reflects out-of-band energy back to the be capable of handling full transmitter power. Age, antenna. In-band energy enters the isolator, and is water invasion, and incorrect cable length will also circulated to the output load. No energy from nearby cause impedance changes. The tuned ports of the transmitters enters the protected transmitter from the isolator provide a constant 50 ohm impedance for the antenna, and intermodulation can be eliminated. transmitter to avoid overheating and oscillation. SPECIFICATIONS Frequency band Tuning range (typ.) Input power VSWR (typ.) Impedance Connectors Temperature range 66-108 MHz ± 3 MHz 50 watts 1.25:1 50 ohms N Female -30°C to +60°C T-1030 Isolator type Single Isolation (typ. / min) 35 dB / 30 dB Insertion loss (typ.) 0.65 dB Load(s) included (1) 35 W Dimensions in. (incl. loads) 4.5 x 4 x 2 cm 11.5 x 10 x 5 Weight lb. (kg) 1.5 (1.4) T-1060 Dual 70 dB / 60 dB 1.0 dB (2) 35 W 6.5 x 4.5 x 2 16.5 x 11.5 x 5 6 (2.7) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 79 TWDS-4001 Rev. 8/09 118 - 174 MHz T-1530 / T-1560 FERRITE ISOLATORS Telewave Single and Dual Ferrite Isolators prevent intermodulation, and protect transmitters from high VSWR or mistuned filtering devices by providing a constant 50 ohm impedance. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 100 watts of power, with several different load options. All Telewave isolators include one or two removeable 35 watt loads in the basic configuration. Typical tuning range is up to ± 4 MHz from the original center frequency, and typical isolation is 35 dB for single, and 70 dB for dual. NOTE: Isolators have limited bandwidth and tuning range. Each isolator is manufactured for a specific range and tuned to a specific frequency. Please specify the exact desired operating frequency and special load requirements with the order. CAVITY-MOUNT ISOLATOR T-1530 SINGLE ISOLATOR T-1560 DUAL ISOLATOR BENEFITS Under adverse conditions, the isolator performs several critical functions: Broken Antenna, Damaged Cable, High VSWR Intermodulation All of these conditions will cause large amounts of When RF energy from a strong nearby signal source power to be reflected down the transmission line enters a transmitter via the antenna, mixing with the toward the transmitter. The circulatory property of the primary transmitter frequency often occurs, resulting isolator will direct this energy to the load port, and in the radiation of new, undesired signals. The isolator protect the transmitter. The load on the isolator must antenna port reflects out-of-band energy back to the be capable of handling full transmitter power. Age, antenna. In-band energy enters the isolator, and is water invasion, and incorrect cable length will also circulated to the output load. No energy from nearby cause impedance changes. The tuned ports of the transmitters enters the protected transmitter from the isolator provide a constant 50 ohm impedance for the antenna, and intermodulation can be eliminated. transmitter to avoid overheating and oscillation. SPECIFICATIONS Frequency band Tuning range (typ.) Input power VSWR (typ.) Impedance Connectors Temperature range 118-174 MHz ± 4 MHz 100 watts 1.25:1 50 ohms N Female -30°C to +60°C Isolator type Isolation (typ. / min) Insertion loss (typ.) Load(s) included Dimensions (incl. loads) in. cm Weight lb. (kg) T-1530 Single 35 dB / 30 dB 0.4 dB (1) 35 W 4.5 x 4 x 2 11.5 x 10 x 5 3 (1.4) T-1560 Dual 70 dB / 60 dB 0.8 dB (2) 35 W 6.5 x 4.5 x 2 16.5 x 11.5 x 5 6 (2.7) 80 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-4005 Rev. 8/09 T-1530M / T-1560M MEDIUM POWER VHF ISOLATORS 148 - 174 MHz 4 ISOLATORS & TERMINATIONS Telewave T-1530M and T-1560M Medium Power Isolators protect transmitters from reflected power, and provide maximum intermodulation suppression. A dualstage unit can provide as much as 70 dB isolation for adjacent channel suppression. The low loss characteristic of the Telewave design insures maximum power transfer to the antenna system. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 115 watts of continuous power, with several different load options. One or two removeable 60 watt loads are included in the basic configuration. Higher power load options can be specified with an order. Telewave isolators are magnetically compensated to allow mounting on any surface without significant detuning. Circulation direction may be specified for special mounting situations. To prevent radiation of harmonics, a cavity or harmonic filter should be placed between the isolator and the antenna. NOTE: ISOL ATORS ARE FACTORY TUNABLE ONLY, AND ARE BUILT FOR A SPECIFIC FREQUENCY. ISOLATION DATA IS MEASURED WITH POWER APPLIED. T-1530M SINGLE ISOLATOR T-1560M DUAL ISOLATOR SPECIFICATIONS Frequency band Input power (continuous) VSWR (typ.) Impedance Connectors Temperature range 148-174 MHz 115 watts 1.3:1 50 ohms N Female -30°C to +60°C Isolator type Isolation (typ. / min) Insertion loss (typ.) Load(s) included Dimensions (incl. loads) in. cm Weight lb. (kg) T-1530M Single 35 dB / 30 dB 0.5 dB (1) 60 W 4 x 5.4 x 2.75 10.2 x 13.7 x 7 3 (1.4) T-1560M Dual 70 dB / 60 dB 0.9 dB (2) 60 W 8.9 x 5.4 x 2.75 22.6 x 13.7 x 7 6 (2.7) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 81 TWDS-4029 Rev. 3/13 T-2230 / T-2260 FERRITE ISOLATORS Telewave Single and Dual Ferrite Isolators prevent intermodulation, and protect transmitters from high VSWR or mistuned filtering devices by providing a constant 50 ohm impedance. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 100 watts of power, with several different load options. All Telewave isolators include one or two removeable 35 watt loads in the basic configuration. Typical tuning range is up to ± 5 MHz from the original center frequency, and typical isolation is 35 dB for single, and 70 dB for dual. NOTE: Isolators have limited bandwidth and tuning range. Each isolator is manufactured for a specific range and tuned to a specific frequency. Please specify the exact desired operating frequency and special load requirements with the order. 216 - 252 MHz T-2230 SINGLE ISOLATOR T-2260 DUAL ISOLATOR BENEFITS Under adverse conditions, the isolator performs several critical functions: Broken Antenna, Damaged Cable, High VSWR Intermodulation All of these conditions will cause large amounts of When RF energy from a strong nearby signal source power to be reflected down the transmission line enters a transmitter via the antenna, mixing with the toward the transmitter. The circulatory property of the primary transmitter frequency often occurs, resulting isolator will direct this energy to the load port, and in the radiation of new, undesired signals. The isolator protect the transmitter. The load on the isolator must antenna port reflects out-of-band energy back to the be capable of handling full transmitter power. Age, antenna. In-band energy enters the isolator, and is water invasion, and incorrect cable length will also circulated to the output load. No energy from nearby cause impedance changes. The tuned ports of the transmitters enters the protected transmitter from the isolator provide a constant 50 ohm impedance for the antenna, and intermodulation can be eliminated. transmitter to avoid overheating and oscillation. SPECIFICATIONS Frequency band Tuning range (typ.) Input power VSWR (typ.) Impedance Connectors Temperature range 216-252 MHz ± 5 MHz 100 watts 1.25:1 50 ohms N Female -30°C to +60°C Isolator type Isolation (typ. / min) Insertion loss (typ.) Load(s) included Dimensions (incl. loads) in. cm Weight lb. (kg) T-2230 Single 35 dB / 30 dB 0.4 dB (1) 35 W 4.5 x 4 x 2 11.5 x 10 x 5 1.5 (1.4) T-2260 Dual 70 dB / 60 dB 0.8 dB (2) 35 W 6.5 x 4.5 x 2 16.5 x 11.5 x 5 6 (2.7) 82 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-4011 Rev. 8/09 ISOLATORS & TERMINATIONS T-3530 / T-3560 FERRITE ISOLATORS Telewave Single and Dual Ferrite Isolators prevent intermodulation, and protect transmitters from high VSWR or mistuned filtering devices by providing a constant 50 ohm impedance. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 150 watts of power, with several different load options. All Telewave isolators include one or two removeable 35 watt loads in the basic configuration. Typical tuning range is up to ± 5 MHz from the original center frequency, and typical isolation is 35 dB for single, and 70 dB for dual. NOTE: Isolators have limited bandwidth and tuning range. Each isolator is manufactured for a specific range and tuned to a specific frequency. Please specify the exact desired operating frequency and special load requirements with the order. 300 - 400 MHz 4 T-3530 SINGLE ISOLATOR T-3560 DUAL ISOLATOR BENEFITS Under adverse conditions, the isolator performs several critical functions: Broken Antenna, Damaged Cable, High VSWR Intermodulation All of these conditions will cause large amounts of When RF energy from a strong nearby signal source power to be reflected down the transmission line enters a transmitter via the antenna, mixing with the toward the transmitter. The circulatory property of the primary transmitter frequency often occurs, resulting isolator will direct this energy to the load port, and in the radiation of new, undesired signals. The isolator protect the transmitter. The load on the isolator must antenna port reflects out-of-band energy back to the be capable of handling full transmitter power. Age, antenna. In-band energy enters the isolator, and is water invasion, and incorrect cable length will also circulated to the output load. No energy from nearby cause impedance changes. The tuned ports of the transmitters enters the protected transmitter from the isolator provide a constant 50 ohm impedance for the antenna, and intermodulation can be eliminated. transmitter to avoid overheating and oscillation. SPECIFICATIONS Frequency band Tuning range (typ.) Input power VSWR (typ.) Impedance Connectors Temperature range 300-400 MHz ± 5 MHz 150 watts 1.25:1 50 ohms N Female -30°C to +60°C Isolator type Isolation (typ. / min) Insertion loss (typ.) Load(s) included Dimensions (incl. loads) in. cm Weight lb. (kg) T-3530 Single 35 dB / 30 dB 0.4 dB (1) 35 W 4.5 x 4 x 2 11.5 x 10 x 5 3 (1.4) T-3560 Dual 70 dB / 60 dB 0.8 dB (2) 35 W 6.5 x 4.5 x 2 16.5 x 11.5 x 5 6 (2.7) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 83 TWDS-4013 Rev. 8/09 400 - 512 MHz T-4530 / T-4560 FERRITE ISOLATORS Telewave Single and Dual Ferrite Isolators prevent intermodulation, and protect transmitters from high VSWR or mistuned filtering devices by providing a constant 50 ohm impedance. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 150 watts of power, with several different load options. All Telewave isolators include one or two removeable 35 watt loads in the basic configuration. Typical tuning range is up to ± 5 MHz from the original center frequency, and typical isolation is 35 dB for single, and 70 dB for dual. T-4530 SINGLE ISOLATOR CAVITY-MOUNT ISOLATOR NOTE: Isolators have limited bandwidth and tuning range. Each isolator is manufactured for a specific range and tuned to a specific frequency. Please specify the exact desired operating frequency and special load requirements with the order. T-4560 DUAL ISOLATOR BENEFITS Under adverse conditions, the isolator performs several critical functions: Broken Antenna, Damaged Cable, High VSWR Intermodulation All of these conditions will cause large amounts of When RF energy from a strong nearby signal source power to be reflected down the transmission line enters a transmitter via the antenna, mixing with the toward the transmitter. The circulatory property of the primary transmitter frequency often occurs, resulting isolator will direct this energy to the load port, and in the radiation of new, undesired signals. The isolator protect the transmitter. The load on the isolator must antenna port reflects out-of-band energy back to the be capable of handling full transmitter power. Age, antenna. In-band energy enters the isolator, and is water invasion, and incorrect cable length will also circulated to the output load. No energy from nearby cause impedance changes. The tuned ports of the transmitters enters the protected transmitter from the isolator provide a constant 50 ohm impedance for the antenna, and intermodulation can be eliminated. transmitter to avoid overheating and oscillation. SPECIFICATIONS Frequency band Tuning range (typ.) Input power VSWR (typ.) Impedance Connectors Temperature range 400-512 MHz ± 5 MHz 150 watts 1.25:1 50 ohms N Female -30°C to +60°C Isolator type Isolation (typ. / min) Insertion loss (typ.) Load(s) included Dimensions (incl. loads) in. cm Weight lb. (kg) T-4530 Single 35 dB / 30 dB 0.4 dB (1) 35 W 4.5 x 4 x 2 11.5 x 10 x 5 3 (1.4) T-4560 Dual 70 dB / 60 dB 0.7 dB (2) 35 W 6.5 x 4.5 x 2 16.5 x 11.5 x 5 6 (2.7) 84 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-4015 Rev. 8/09 ISOLATORS & TERMINATIONS T-7530 / T-7560 FERRITE ISOLATORS Telewave Single and Dual Ferrite Isolators prevent intermodulation, and protect transmitters from high VSWR or mistuned filtering devices by providing a constant 50 ohm impedance. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 150 watts of power, with several different load options. All Telewave isolators include one or two removeable 35 watt loads in the basic configuration. Typical tuning range is up to ± 6 MHz from the original center frequency, and typical isolation is 35 dB for single, and 70 dB for dual. NOTE: Isolators have limited bandwidth and tuning range. Each isolator is manufactured for a specific range and tuned to a specific frequency. Please specify the exact desired operating frequency and special load requirements with the order. 700 - 806 MHz 4 T-7530 SINGLE ISOLATOR T-7560 DUAL ISOLATOR BENEFITS Under adverse conditions, the isolator performs several critical functions: Broken Antenna, Damaged Cable, High VSWR Intermodulation All of these conditions will cause large amounts of When RF energy from a strong nearby signal source power to be reflected down the transmission line enters a transmitter via the antenna, mixing with the toward the transmitter. The circulatory property of the primary transmitter frequency often occurs, resulting isolator will direct this energy to the load port, and in the radiation of new, undesired signals. The isolator protect the transmitter. The load on the isolator must antenna port reflects out-of-band energy back to the be capable of handling full transmitter power. Age, antenna. In-band energy enters the isolator, and is water invasion, and incorrect cable length will also circulated to the output load. No energy from nearby cause impedance changes. The tuned ports of the transmitters enters the protected transmitter from the isolator provide a constant 50 ohm impedance for the antenna, and intermodulation can be eliminated. transmitter to avoid overheating and oscillation. SPECIFICATIONS Frequency band Tuning range (typ.) Input power VSWR (typ.) Impedance Connectors Temperature range 700-806 MHz ± 6 MHz 150 watts 1.25:1 50 ohms N Female -30°C to +60°C Isolator type Isolation (typ. / min) Insertion loss (typ.) Load(s) included Dimensions (incl. loads) in. cm Weight lb. (kg) T-7530 Single 35 dB / 30 dB 0.4 dB (1) 35 W 4.5 x 4 x 2 11.5 x 10 x 5 3 (1.4) T-7560 Dual 70 dB / 60 dB 0.8 dB (2) 35 W 6.5 x 4.5 x 2 16.5 x 11.5 x 5 6 (2.7) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 85 TWDS-4021 Rev. 8/09 T-8630 / T-8660 FERRITE ISOLATORS Telewave Single and Dual Ferrite Isolators prevent intermodulation, and protect transmitters from high VSWR or mistuned filtering devices by providing a constant 50 ohm impedance. All Telewave isolators are manufactured and tested in our own plant to the highest quality standards. These isolators handle up to 150 watts of power, with several different load options. All Telewave isolators include one or two removeable 35 watt loads in the basic configuration. Typical tuning range is up to ± 6 MHz from the original center frequency, and typical isolation is 35 dB for single, and 70 dB for dual. NOTE: Isolators have limited bandwidth and tuning range. Each isolator is manufactured for a specific range and tuned to a specific frequency. Please specify the exact desired operating frequency and special load requirements with the order. 806 - 960 MHz T-8630 SINGLE ISOLATOR T-8660 DUAL ISOLATOR BENEFITS Under adverse conditions, the isolator performs several critical functions: Broken Antenna, Damaged Cable, High VSWR Intermodulation All of these conditions will cause large amounts of When in-band or out-of-band RF energy from a strong power to be reflected down the transmission line nearby signal source enters a transmitter via the toward the transmitter. The circulatory property of the antenna, mixing with the primary transmitter frequency isolator will direct this energy to the load port, and often occurs, resulting in the radiation of new, protect the transmitter. The load on the isolator must undesired signals. The isolator antenna port reflects be capable of handling full transmitter power. Age, out-of-band energy back to the antenna. In-band water invasion, and incorrect cable length will also energy enters the isolator, and is circulated to the cause impedance changes. The tuned ports of the output load. No energy from nearby transmitters isolator provide a constant 50 ohm impedance for the enters the protected transmitter from the antenna, transmitter to avoid overheating and oscillation. and intermodulation can be eliminated. SPECIFICATIONS Frequency band Tuning range (typ.) Input power VSWR (typ.) Impedance Connectors Temperature range 806-960 MHz ± 6 MHz 150 watts 1.25:1 50 ohms N Female -30°C to +60°C Isolator type Isolation (typ. / min) Insertion loss (typ.) Load(s) included Dimensions (incl. loads) in. cm Weight lb. (kg) T-8630 Single 35 dB / 30 dB 0.4 dB (1) 35 W 4.5 x 4 x 2 11.5 x 10 x 5 3 (1.4) T-8660 Dual 70 dB / 60 dB 0.8 dB (2) 35 W 6.5 x 4.5 x 2 16.5 x 11.5 x 5 6 (2.7) 86 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-4023 Rev. 8/09 ISOLATORS & TERMINATIONS HIGH POWER ISOLATORS SINGLE AND DUAL STAGE TO 400 WATTS 148 - 960 MHz 4 Telewave High Power Isolators provide maximum effectiveness in intermodulation suppression. A dual-stage unit can provide as much as 85 dB isolation for adjacent channel suppression, and better than 60 dB across the entire bandwidth. The low loss characteristic of the Telewave design insures maximum power transfer to the antenna system. T-1530H T-1560H Telewave isolators are magnetically compensated to allow mounting on any surface without significant detuning. Circulation direction may be specified for special mounting situations. To prevent radiation of harmonics, a cavity or harmonic filter should be placed between the isolator and the antenna. T-4530H T-4560H T-8660H Telewave High Power Isolators are One or two removable 60 watt loads available in single or dual stage are supplied standard. Optional configurations from 148 to 960 loads to 300 watts are available. MHz. Power capability of up to Con sult Telewave with load 400 watts is available, and many requirements, and special mounting different termination options can or mechanical configurations. be specified. NOTE: HIGH POWER ISOLATORS ARE NOT FIELD TUNABLE, AND ARE MANUFACTURED FOR A SPECIFIC FREQUENCY. ISOLATION DATA IS MEASURED WITH POWER APPLIED. SPECIFICATIONS Isolator type Frequency range (MHz) Isolation (typ.) Isolation (min) Insertion loss (typ.) VSWR (typ.) Maximum power Connectors Temperature Dimensions incl. loads in. cm T-1530H T-1560H T-4530H T-4560H T-8660H Single Dual Single Dual Dual 148-174 148-174 440-475 440-475 806-960 35 dB 65 dB 35 dB 80 dB 70 dB 30 dB 55 dB 30 dB 60 dB 60 dB 0.6 dB 0.9 dB 0.5 dB 0.8 dB 0.8 dB 1.25:1 300 W 300 W 400 W 400 W 300 W N Female -30 to +60 °C 6.75 x 5 x 2.625 9.75 x 6.75 x 2.75 6.5 x 5.25 x 2.5 9 x 6.5 x 2.5 6.5 x 5.25 x 2.75 17.1 x 12.7 x 6.7 24.8 x 17.1 x 7 16.5 x 13.3 x 6.4 22.9 x 16.5 x 6.4 16.5 x 13.3 x 7 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 87 TWDS-4026 Rev. 3/09 118 - 960 MHz TS150, 220, 350, 450, 760, 900 SERIES INTERMOD SUPPRESSION PANELS Telewave Intermod Suppression Panels provide a simple, affordable, high-performance solution for cleaning up interference at congested radio sites, when a full combining system may not be costeffective. In addition to controlling transmitter intermodulation, IM Panels also greatly reduce transmitter maintenance and expensive repairs by providing a constant 50 ohm load, protecting the transmitter from opens, shorts, or other faults in the antenna system. Telewave IM Panels do not rely on any cables or other lossy interconnections, other than to the transmit chain. Each standard or custom panel includes one or more isolators with appropriate terminations, and a low-pass filter. Each panel is factory tuned to specific frequencies supplied with the order. All 100 and 150 watt units are field tunable by approximately ± 3-6 MHz depending on frequency, and include complete tuning instructions. No specialized equipment is required. 150 watt units ship with a 35 watt primary load, and a 50 watt termination on the antenna isolation (2nd) port. 300 and 400 watt units ship with a 100 watt second stage termination, and are not field tunable. Center frequency and load requirements must be specified when ordering. Contact Telewave if additional information or assistance is required. TS450PB1 TS150PB2-SP COMMON SPECIFICATIONS Tuning range (100-150 W units only) ± 3-6 MHz (depending on freq.) Impedance (nom.) 50 ohms VSWR (max) 1.3:1 Harmonic attenuation (min) 60 dB Connectors N Female MODEL FREQ. INPUT ISOLATION (dB) INS. LOSS (dB) PANEL LOAD RANGE POWER TYP MIN TYP HEIGHT POWER TS150PA1 118-174 100 W 38 30 0.6 5.25 in. 50 W TS150PB1 118-174 100 W 75 60 0.9 5.25 in. 50 W TS150PA2 148-174 300 W 30 21 0.7 8.75 in. 100 W TS150PB2 148-174 300 W 60 42 1.0 8.75 in. 100 W TS220PA1 216-250 100 W 38 30 0.6 5.25 in. 50 W TS220PB1 216-250 100 W 75 60 0.9 5.25 in. 50 W TS350PA1 300-400 150 W 38 30 0.6 5.25 in. 50 W TS350PB1 300-400 150 W 75 60 0.9 5.25 in. 50 W TS450PA1 400-512 150 W 38 30 0.5 5.25 in. 50 W TS450PB1 400-512 150 W 75 60 0.8 5.25 in. 50 W TS450PA2 440-475 400 W 38 30 0.6 8.75 in. 100 W TS450PB2 440-475 400 W 75 60 0.9 8.75 in. 100 W TS760PA1 763-869 150 W 38 30 0.6 5.25 in. 50 W TS760PB1 763-869 150 W 75 60 0.6 5.25 in. 50 W TS760PB2 763-869 300 W 75 60 0.9 8.75 in. 100 W TS900PA1 806-960 150 W 38 30 0.6 5.25 in. 50 W TS900PB1 806-960 150 W 75 60 0.9 5.25 in. 50 W TS900PB2 806-960 300 W 75 60 0.9 8.75 in. 100 W 88 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-4027 Rev. 10/12 THRP-1548, 4548, 7648, 8648 HIGH PERFORMANCE REPEATER PANEL 138 - 960 MHz 4 ISOLATORS & TERMINATIONS The Telewave High Performance The output of the preselector is Repeater Panel greatly improves coupled to one of two types of the effective sensitivity and low-noise preamplifiers. The selectivity of a repeater receiver for standard configuration uses a TLA extended mobile and portable series low-noise bipolar preamp. coverage, and provides maximum This preamp is recommended for intermodulation protection for the areas that are prone to lightning transmitter. damage or high ambient signal The THRP panel uses a dual isolator levels. with a 50 watt termination on the The optional TGA series preamps second stage output, and a low use a PHEMT amplifier for higher pass filter for transmitter IM sensitivity. This preamp is protection. This combination recommended for sites with low provides more than 60 dB of IM existing RF noise levels. protection over a ±5 MHz bandwidth, and transmitter 2nd harmonic attenuation of over 50 dB. The THRP series puts all this equipment on one 14" x 19" panel, pretuned and ready to install. The total price is less then if the The duplexer utilizes four 4" cavities e q u i p m e n t w a s p u r c h a s e d in a pass/reject configuration. This separately, and requires less rack duplexer has only 1.8 dB insertion space. loss, and provides over 110 dB isolation. The receiver side of the duplexer is interconnected to two 8" high "Q" bandpass cavities, to form a narrow pass-band preselector. FREQUENCY RANGES THRP-1548 138 - 174 MHz THRP-4548 400 -512 MHz THRP-7648 763 - 869 MHz THRP-8648 806 -960 MHz THRP-7648 FRONT THRP-7648 BACK SPECIFICATIONS Frequency range Frequency separation (min) Power input (continuous) VSWR (max) TX-RX isolation (typ.) Insertion loss TX to Antenna (typ.) TX 2nd harmonic attn. (typ.) Antenna to TX isolation (typ.) RX-TX isolation (typ.) Temperature range Connector type Finish Dimensions (HWD) in. (cm) Net weight lb. (kg) PREAMP 138-960 MHz Gain - Antenna to RX 3 MHz Noise figure (typ.) 125 watts 3rd order intercp. 1.22:1 Input power 110 dB Current (typ.) 1.8 dB 50 dB 75 dB at 5 MHz 120 dB -30°C to +40°C N Female Grained aluminum 14 x 19 x 12 (35.6 x 48.3 x 30.5) 25 (11.4) (400-860 MHz) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com Bipolar +8 to +20 dB 2.5 dB +35 dBm +12 to +24 VDC 170 mA PHEMT (opt.) +8 to +15 dB 0.7 dB +25 dBm +9 to +18 VDC 40 mA All specifications subject to change without notice 89 TWDS-4028 Rev. 10/13 5 CAVITIES AND FILTERS 5 CAVITIES AND FILTERS Bandpass Bandpass cavities allow a single frequency or a very narrow group of frequencies to reach a receiver, or leave a transmitter. All other frequencies are rejected by these filters. Bandpass / Bandreject Pass / Reject cavities offer a modified pass response for a narrow band of frequencies, and also provide a tunable notch which deepens the reject response at a particular frequency. This type of filter supports closer frequency spacing than a standard pass cavity. Notch Notch cavities reject a particular frequency or a narrow window of frequencies. These cavities have extremely low insertion loss and are very useful as standalone devices or in addition to passband filters. Single / Dual / Triple Multiple cavities provide a wider passband or reject band, or a steeper roll-off outside the pass or reject band. They also enable multiple-window filters which can pass or reject more than one group of frequencies within a band. Lowpass / Highpass / Crystal Low pass filters help to eliminate harmonics and spurs which may occur above the fundamental frequency of a transmitter. Highpass filters attenuate unwanted energy below the fundamental frequency, and are also used to protect receivers. Crystal filters provide extremely sharp response to protect receivers from closely-spaced transmitters. TWPC-0310-1, 0410-1 BANDPASS CAVITIES The Telewave TWPC-0310-1 and Excellent frequency stability is TWPC-0410-1 are 10" diameter, achieved by the use of a specially ¼-wavelength, high "Q" bandpass mac hined comp en s ator and c av i t y f i l t e r s w i t h s u p e r i o r Invar rod. The pass frequency is selectivity. Bandpass cavities reject temperature stable from -30°C to all frequencies outside a narrow +70°C. Ground loop technology pass band. These cavities reduce places the center pin of each transmitter sideband noise, and coupling loop at DC ground also protect receivers against potential. desensitization. Heavy duty materials are used The TWPC-0310-1 covers 3040 throughout each cavity to insure MHz, and the TWPC-0410-1 covers high performance and long life. 4050 MHz. The tuning range of Cavity top plates are machined these cavities is approximately from ¼-inch aluminum, and are ±2.5 MHz from center frequency heliarc welded to the cavity body at as built. All cavities are tuned to the high current point for improved specified frequencies prior to conductivity and strength. This shipping. No further adjustments allows Telewave cavities to handle should be required. The positive up to 350 watts, depending on locking mechanism allows for quick insertion loss. field re-tuning if frequency changes become necessary. Rigid foam inserts support the tuner assembly allowing vertical These cavities feature calibrated or horizontal mounting. Similar adjustable coupling, so that insertion metals and alodined aluminum help loss can be easily set from 0.5 dB to prevent galvanic corrosion. Silver 2 dB or more with corresponding plated tuners and beryllium copper increases in selectivity. This allows finger stock provide non-corrosive cavity response to be optimized low loss contact, and ensure reliable, for any operating environment. At long-term performance. densely populated sites, the 0310 / 0410-2 dual and 0310 / 0410-3 triple cavity filters provide much greater selectivity with minimum insertion loss. Multiple cavities can also provide a wider passband when required. Mounting rails are provided for all multiple-cavity filters. 30 - 50 MHz 92 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5011 Rev. 10/07 CAVITIES & FILTERS TWPC-0310-1, 0410-1 30 - 50 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 - TWPC-0310 0 Figure 2 - TWPC-0410 0 10 20 0.5 dB 30 1.0 dB 2.0 dB 40 10 20 0.5 dB 1.0 dB 30 2.0 dB 40 50 50 60 60 70 70 -2 -1 Fc +1 +2 Frequency (MHz) -2 -1 Fc +1 +2 MODEL Frequency coverage Tuning range from center frequency Insertion loss (adjustable) Attenuation Cavity dimensions (Diam. x H) in. (cm) Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Connectors Finish TWPC-0310 30-40 MHz ± 2.5 MHz 0.5 to 2.0 dB See figure 1 10 x 88 (25 x 224) 10 x 97 (25 x 246) 29 (13.2) 40 (18.2) TWPC-0410 40-50 MHz ± 2.5 MHz 0.5 to 2.0 dB See figure 2 10 x 72 (25 x 183) 10 x 81 (25 x 206) 26 (11.8) 36 (16.3) 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper N or UHF female (opt.) Gray acrylic enamel Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 93 TWDS-5011 Rev. 10/07 40 - 50 MHz TWPC-0412-1, TWNC-0412-1 BANDPASS CAVITY, NOTCH CAVITY The Telewave TWPC-0412-1 is a 12" Multiple cavities can also provide diameter, ¼-wavelength high "Q" a wider passband or notch when bandpass cavity filter with superior required. Mounting rails are selectivity. Band-pass cavities reject provided for all multiple-cavity all frequencies outside a narrow filters. pass band. These cavities reduce transmitter sideband noise, and also protect receivers against desensitization. Excellent frequency stability is achieved by the use of a specially machined compensator and Invar rod. The pass frequency is The TWNC-0412-1 is a 12" diameter, temperature stable from -30°C ¼-wavelength notch cavity with an to +70°C. Telewave Ground Loop adjustable coupling loop. These technology places the center cavities reject a narrow band of conductor of each coupling loop at frequencies, and are often used DC ground potential for lightning in conjunction with pass cavities in protection and noise reduction. complex filtering designs. Notch cavities have very low loss outside the notch band, and Telewave can also "tilt" the notch response to move a notch very close to a pass frequency without adversely affecting the pass response. Heavy duty materials are used throughout each cavity to insure high performance and long life. Cavity top plates are machined from ¼-inch aluminum, and are heliarc welded to the cavity body at the high current point for improved The TWPC and TWNC-0412-1 conductivity and strength. This cover 40-50 MHz. The tuning range allows Telewave cavities to handle of these cavities is approximately up to 350 watts, depending on ±2.5 MHz from center frequency insertion loss. as built. All cavities are tuned to specified frequencies prior to shipping. No further adjustments should be required. The positive locking mechanism allows for quick field re-tuning if frequency changes become necessary. Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar metals and alodined aluminum help prevent galvanic corrosion. Silver plated tuners and beryllium copper finger stock provide non-corrosive These cavities feature calibrated low loss contact, and ensure reliable, adjustable coupling, so that pass long-term performance. cavity insertion loss can be easily set from 0.5 dB to 2 dB or more with corresponding increases in selectivity. This allows cavity response to be optimized for any operating environment. At densely populated sites, the 0412-2 dual pass cavity filter provides greater selectivity. 94 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5025 Rev. 9/08 CAVITIES & FILTERS TWPC-0412-1, TWNC-0412-1 40 - 50 MHz 5 Attenuation in dB 0 10 20 30 40 50 60 70 80 -1.0 TYPICAL RESPONSE Figure 1 - TWPC-0412-1 -0.5 Fc 0 10 20 30 40 50 60 70 80 +0.5 +1.0 -1.0 Frequency (MHz) Figure 2 - TWNC-0412-1 -0.5 Fc +0.5 +1.0 SPECIFICATIONS Frequency coverage Tuning range from center frequency Insertion loss (adjustable on pass cavity) Attenuation at 1 dB insertion loss Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Maximum dimensions with tuners extended in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) TWPC / TWNC-0412-1 40-50 MHz ± 2.5 MHz 0.5 to 2.0 dB (Notch cavity 0.2 dB max) See Figure 1, 2 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 12 x 72 (30 x 183) 12 x 81 (30 x 206) N or UHF female (opt.) Gray acrylic enamel 27 (68.6) 38 (96.5) NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 95 TWDS-5025 Rev. 9/08 88 - 108 MHz TWPC-1005-1,2 BANDPASS CAVITIES The Telewave T WPC-10 05 -1, Heavy duty materials are used and 10 05 -2 are 5" diameter, throughout each cavity to insure ¼-wavelength, high "Q" bandpass high performance and long life. cavity filter with superior selectivity. Cavity top plates are machined Bandpass cavities rejec t all from ¼-inch aluminum, and are frequencies out side a narrow heliarc welded to the cavity body at pass band. These cavities reduce the high current point for improved transmitter sideband noise, and conductivity and strength. This also protect receivers against allows Telewave cavities to handle desensitization. up to 350 watts, depending on TWPC-1005 cavities cover 88-108 insertion loss. MHz, and can be tuned at 50 or Rigid foam inserts support the 75 ohms upon request. All cavities tuner assembly allowing vertical are tuned to specified frequencies or horizontal mounting. Similar prior to shipping, and no further metals and alodined aluminum help adjustments should be required. prevent galvanic corrosion. Silver The positive locking mechanism plated tuners and beryllium copper allows for quick field re-tuning finger stock provide non-corrosive if frequency changes become low loss contact, and ensure reliable, necessary. long-term performance. These cavities feature calibrated adjustable coupling, and insertion loss can be easily set from 0.5 dB to 2 dB or more to improve selectivity. This allows cavity response to be optimized for any operating environment. At densely populated sites, the TWPC-1005-2 dual cavity filter provides greater selectivity with minimum insertion loss. Multiple cavities can also provide a wider passband when required. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is achieved by the use of a specially machined compensator and Invar rod. The pass frequency is temperature stable from -30°C to +70°C. Telewave Ground Loop technology places the center conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. 96 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com TWPC-1005-1 TWPC-1005-2 All specifications subject to change without notice TWDS-5034 Rev. 10/08 CAVITIES & FILTERS TWPC-1005-1,2 88 - 108 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 TWPC-1005-1 SINGLE Figure 2 TWPC-1005-2 DUAL 0 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 -5 -2.5 Fc +2.5 +5 -5 -2.5 Fc +2.5 +5 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation at 1 db insertion loss Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-1005-1 0.5 to 2.0 dB See figure 1 5 x 48 (13 x 123) 5 (2.3) 8 (3.6) TWPC-1005-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 48 (13 x 48 x 123) 12 (5.5) 16 (7.3 88-108 MHz 50 ohms (75 ohm opt.) 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 5 x 36 (13 x 91) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 97 TWDS-5034 Rev. 10/08 88 - 108 MHz TWPC-1008-1, 2 BANDPASS CAVITIES The Telewave TWPC-1008-1 and Heavy duty materials are used TWPC-1008-2 are 8" diameter, throughout each cavity to insure ¼-wavelength, high "Q" bandpass high performance and long life. c avit y f ilter s with superior Cavity top plates are machined selectivity. Bandpass cavities reject from ¼-inch aluminum, and are all frequencies outside a narrow heliarc welded to the cavity body at pass band. These cavities reduce the high current point for improved transmitter sideband noise, and conductivity and strength. This also protect receivers against allows Telewave cavities to handle desensitization. up to 350 watts, depending on TWPC-1008 cavities cover 88-108 insertion loss. MHz, and can be tuned at 50 or Rigid foam inserts support the 75 ohms upon request. All cavities tuner assembly allowing vertical are tuned to specified frequencies or horizontal mounting. Similar prior to shipping, and no further metals and alodined aluminum help adjustments should be required. prevent galvanic corrosion. Silver The positive locking mechanism plated tuners and beryllium copper allows for quick field re-tuning finger stock provide non-corrosive if frequency changes become low loss contact, and ensure reliable, necessary. long-term performance. These cavities feature calibrated adjustable coupling, and insertion loss can be easily set from 0.5 dB to 2 dB or more to improve selectivity. This allows cavity response to be optimized for any operating environment. At densely populated sites, the TWPC-1008-2 dual cavity filter provides greater selectivity with minimum insertion loss. Multiple cavities can also provide a wider passband when required. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is achieved by the use of a specially machined compensator and Invar rod. The pass frequency is temperature stable from -30°C to +70°C. Telewave Ground Loop technology places the center conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. 98 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com TWPC-1008-1 TWPC-1008-2 All specifications subject to change without notice TWDS-5035 Rev. 12/06 CAVITIES & FILTERS TWPC-1008-1, 2 88 - 108 MHz 5 Attenuation in dB Figure 1 TYPICAL SELECTIVITY CHARACTERISTICS TWPC-1008-1 SINGLE Figure 2 TWPC-1008-2 DUAL 0 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 -5 -2.5 Fc +2.5 +5 -5 -2.5 Fc +2.5 +5 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation at 1 db insertion loss Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-1008-1 0.5 to 2.0 dB See figure 1 8 x 48 (20 x 123) 11 (5) 16 (7.3) TWPC-1008-2 1.0 to 4.0 dB See figure 2 8.25 x 19 x 48 (20 x 48 x 123) 24 (10.9) 30 (13.6) 88-108 MHz 50 ohms (75 ohm opt.) 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Threaded Invar Beryllium copper 8 x 36 (13 x 91) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5035 Rev. 12/06 99 88 - 108 MHz TPRC-1005-1, 2 PASS-REJECT CAVITIES The Telewave TPRC-1005-1 and conductor of each coupling loop at TPRC-1005-2 are 5" diameter, DC ground potential for lightning ¼-wavelength Pass-Reject cavities protection and noise reduction. with an adjustable coupling loop and tuning capacitor. Pass-Reject cavities reject all frequencies outside a narrow pass band, with a tunable notch for additional protection with close spacing. These cavities are commonly used to reduce transmitter sideband noise, and protect receivers against desensitization. Heavy duty materials are used throughout each cavity to insure high performance and long life. Cavity top plates are machined from ¼-inch aluminum, and are heliarc welded to the cavity body at the high current point for improved conductivity and strength. This allows Telewave cavities to handle up to 350 watts, depending on TPRC-1005 cavities cover 88-108 insertion loss. MHz, and can be tuned at 50 or 75 ohms upon request. All cavities are tuned to specified frequencies prior to shipping, and no further adjustments should be required. The positive locking mechanism allows for quick field re-tuning if frequency changes become necessary. Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar metals and alodined aluminum help prevent galvanic corrosion. Silver plated tuners and beryllium copper finger stock provide non-corrosive low loss contact, and ensure reliable, long-term performance. These cavities feature calibrated adjustable coupling, and insertion loss can be easily set from 0.5 dB to 2 dB or more to improve selectivity. This allows cavity response to be optimized for any operating environment. At densely populated sites, the TPRC-1005-2 dual cavity filter provides greater selectivity with minimum insertion loss. Multiple cavities can also provide a wider passband when required. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is achieved by the use of a specially machined compensator and Invar rod. The pass and reject frequencies are temperature stable from -30°C to +70°C. Telewave Ground Loop technology places the center 100 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com TPRC-1005-1 TPRC-1005-2 All specifications subject to change without notice TWDS-5007 Rev. 3/10 CAVITIES & FILTERS TPRC-1005-1, 2 88 - 108 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 TPRC-1005-1 0 Figure 2 TPRC-1005-2 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 -0.2 0 +0.2 +0.4 +0.6 +0.8 +1.0 +1.2 -0.2 0 +0.2 +0.4 +0.6 +0.8 +1.0 +1.2 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation at 1 db insertion loss Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TPRC-1005-1 0.5 to 2.0 dB See figure 1 5 x 46 (13 x 117) 5 (2.3) 8 (3.6) TPRC-1005-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 46 (13 x 48 x 117) 12 (5.5) 16 (7.3) 88-108 MHz 50 ohms (75 ohm opt.) 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +60°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Threaded Invar Beryllium copper 5 x 36 (13 x 91) N or UHF female (opt.) Gray acrylic enamel NOTE: Customized response curves are available to meet exact system requirements. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5007 Rev. 3/10 101 88 - 108 MHz TPRC-1008-1, 2 PASS-REJECT CAVITIES The Telewave TPRC-1008-1 and conductor of each coupling loop at TPRC-1008-2 are 8" diameter, DC ground potential for lightning ¼-wavelength Pass-Reject cavities protection and noise reduction. with an adjustable coupling loop and tuning capacitor. Pass-Reject cavities reject all frequencies outside a narrow pass band, with a tunable notch for additional protection with close spacing. These cavities are commonly used to reduce transmitter sideband noise, and protect receivers against desensitization. Heavy duty materials are used throughout each cavity to insure high performance and long life. Cavity top plates are machined from ¼-inch aluminum, and are heliarc welded to the cavity body at the high current point for improved conductivity and strength. This allows Telewave cavities to handle up to 350 watts, depending on TPRC-1008 cavities cover 88-108 insertion loss. MHz, and can be tuned at 50 or 75 ohms upon request. All cavities are tuned to specified frequencies prior to shipping, and no further adjustments should be required. The positive locking mechanism allows for quick field re-tuning if frequency changes become necessary. Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar metals and alodined aluminum help prevent galvanic corrosion. Silver plated tuners and beryllium copper finger stock provide non-corrosive low loss contact, and ensure reliable, long-term performance. These cavities feature calibrated adjustable coupling, and insertion loss can be easily set from 0.5 dB to 2 dB or more to improve selectivity. This allows cavity response to be optimized for any operating environment. At densely populated sites, the TPRC-1008-2 dual cavity filter provides greater selectivity with minimum insertion loss. Multiple cavities can also provide a wider passband when required. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is achieved by the use of a specially machined compensator and Invar rod. The pass and reject frequencies are temperature stable from -30°C to +70°C. Telewave Ground Loop technology places the center 102 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com TPRC-1008-1 TPRC-1008-2 All specifications subject to change without notice TWDS-5008 Rev. 10/12 CAVITIES & FILTERS TPRC-1008-1, 2 88 - 108 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 TPRC-1008-1 0 0 Figure 2 TPRC-1008-2 10 10 20 20 30 30 40 40 50 50 60 60 70 70 -0.1 0 +0.1 +0.2 +0.3 +0.4 +0.5 +0.6 -0.2 0 +0.2 +0.4 +0.6 +0.8 +1.0 +1.2 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation at 1 db insertion loss Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) TPRC-1008-1 0.5 to 2.0 dB See figure 1 8 x 46 (20 x 117) 11 (5) 16 (7.3) TPRC-1008-2 1.0 to 4.0 dB See figure 2 8.25 x 19 x 46 (20 x 48 x 117) 24 (10.9) 30 (13.6) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish 88-108 MHz 50 ohms (75 ohm opt.) 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +60°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 8 x 36 (13 x 91) N or UHF female (opt.) Gray acrylic enamel NOTE: Customized response curves are available to meet exact system requirements. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5008 Rev. 10/12 103 88 - 108 MHz TWNC-1005-1, 2 NOTCH CAVITIES The Telewave TWNC-1005-1 and DC ground potential for lightning TWNC-1005-2 are 5" diameter, protection and noise reduction. ¼-wavelength notch cavities with an adjustable coupling loop. Notch cavities are typically used together with Pass or Pass/Reject cavities to eliminate a particular frequency. Notch cavities have very low loss outside the notch band. Telewave can also "tilt" the notch response to move a notch very close to a pass frequency without adversely affecting the pass response. Heavy duty materials are used throughout each cavity to insure high performance and long life. Cavity top plates are machined from ¼-inch aluminum, and are heliarc welded to the cavity body at the high current point for improved conductivity and strength. This allows Telewave cavities to handle up to 350 watts, depending on insertion loss. TWNC-1005 cavities cover 88-108 MHz, and can be tuned at 50 or 75 ohms upon request. All cavities are tuned to specified frequencies prior to shipping, and no further adjustments should be required. The positive locking mechanism allows for quick field re-tuning if frequency changes become necessary. Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar metals and alodined aluminum help prevent galvanic corrosion. Silver plated tuners and beryllium copper finger stock provide non-corrosive low loss contact, and ensure reliable, long-term performance. These cavities feature calibrated adjustable coupling, which can be easily changed to improve notch depth. This allows cavity response to be optimized for any operating environment. At densely populated sites, the TWNC-1005-2 dual cavity filter provides a deeper notch with minimum insertion loss. Multiple cavities can also provide a wider passband when required. Mounting rails are provided for all multiplecavity filters. Excellent frequency stability is achieved by the use of a specially machined compensator and Invar rod. The notch frequency is temperature stable from -30°C to +70°C. Telewave Ground Loop technology places the center conductor of each coupling loop at 104 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com TWNC-1005-1 TWNC-1005-2 All specifications subject to change without notice TWDS-5009 Rev. 10/08 CAVITIES & FILTERS TWNC-1005-1, 2 88 - 108 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS 0 Figure 1 TWNC-1005-1 0 Figure 2 TWNC-1005-2 10 10 20 20 30 30 40 40 50 50 60 60 70 70 -3 -2 -1 Fc +1 +2 +3 -6 -4 -2 Fc +2 +4 +6 Frequency (MHz) MODEL TWNC-1005-1 Insertion loss (max) 0.2 dB Attenuation at notch frequency See figure 1 Maximum dimensions with tuners extended in. (cm) 5 x 46 (13 x 117) Net weight lb. (kg) 5 (2.3) Shipping weight lb. (kg) 8 (3.6) COMMON SPECIFICATIONS Tuning frequency range 88-108 MHz Nominal impedance 50 ohms (75 ohm opt.) VSWR at resonance (max) 1.5:1 Input power (max) 350 watts Temperature range -30°C to +60°C Cavity electrical length 1/4 wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 5 x 36 (13 x 91) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: Pass cavities are also available in 8" and 10" diameter Customized response curves are available to meet exact system requirements. Contact Telewave for recommendations on your specific design. TWNC-1005-2 0.4 dB See figure 2 5.25 x 19 x 46 (13 x 48 x 117) 12 (5.5) 16 (7.3 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5009 Rev. 10/08 105 88 - 108 MHz TWNC-1008-1, 2 NOTCH CAVITIES The Telewave TWNC-1008-1 and DC ground potential for lightning TWNC-1008-2 are 8" diameter, protection and noise reduction. ¼-wavelength notch cavities with an adjustable coupling loop. Notch cavities are typically used together with Pass or Pass/Reject cavities to eliminate a particular frequency. Notch cavities have very low loss outside the notch band. Telewave can also "tilt" the notch response to move a notch very close to a pass frequency without adversely affecting the pass response. Heavy duty materials are used throughout each cavity to insure high performance and long life. Cavity top plates are machined from ¼-inch aluminum, and are heliarc welded to the cavity body at the high current point for improved conductivity and strength. This allows Telewave cavities to handle up to 350 watts, depending on insertion loss. TWNC-1008 cavities cover 88-108 MHz, and can be tuned at 50 or 75 ohms upon request. All cavities are tuned to specified frequencies prior to shipping, and no further adjustments should be required. The positive locking mechanism allows for quick field re-tuning if frequency changes become necessary. Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar metals and alodined aluminum help prevent galvanic corrosion. Silver plated tuners and beryllium copper finger stock provide non-corrosive low loss contact, and ensure reliable, long-term performance. These cavities feature calibrated adjustable coupling, which can be easily changed to improve selectivity. This allows cavity response to be optimized for any operating environment. At densely populated sites, the TWNC-1008-2 dual cavity filter provides a deeper notch with minimum insertion loss. Multiple cavities can also provide a wider notch when required. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is achieved by the use of a specially machined compensator and Invar rod. The notch frequency is temperature stable from -30°C to +70°C. Telewave Ground Loop technology places the center conductor of each coupling loop at 106 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com TWNC-1008-1 TWNC-1008-2 All specifications subject to change without notice TWDS-5010 Rev. 10/12 CAVITIES & FILTERS TWNC-1008-1, 2 88 - 108 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 TWNC-1008-1 0 0 Figure 2 TWNC-1008-2 10 10 20 20 30 30 40 40 50 50 60 60 70 70 -0.6 -0.4 -0.2 Fc +0.2 +0.4 +0.6 -0.6 -0.4 -0.2 Fc +0.2 +0.4 +0.6 Frequency (MHz) MODEL TWNC-1008-1 TWNC-1008-2 Insertion loss (max) 0.2 dB 0.4 dB Attenuation at notch frequency See figure 1 See figure 2 Maximum dimensions with tuners extended in. (cm) 8 x 46 (20.3 x 117) 8.25 x 19 x 46 (20 x 48 x 117) Net weight lb. (kg) 11 (5) 24 (10.9) Shipping weight lb. (kg) 16 (7.3) 30 (13.6) COMMON SPECIFICATIONS Tuning frequency range 88-108 MHz Nominal impedance 50 ohms (75 ohm opt.) VSWR at resonance (max) 1.5:1 Input power (max) 350 watts Temperature range -30°C to +60°C Cavity electrical length 1/4 wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 8 x 36 (20 x 91) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: Pass cavities are also available in 8" and 10" diameter Customized response curves are available to meet exact system requirements. Contact Telewave for recommendations on your specific design. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5010 Rev. 10/12 107 TWPC-1405-1, 2, 3 BANDPASS CAVITIES 118 - 148 MHz TWPC-1405-1 TWPC-1405-2 TWPC-1405-3 The Telewave TWPC-1405-1, 1405- be optimized for any operating from ¼-inch aluminum, and are 2, and 1405-3 are 5" diameter, environment. At densely populated heliarc welded to the cavity body at ¼-wavelength, high "Q" bandpass sites, the 1405-2 or 1405-3 cavity the high current point for improved c a v i t y f i l t e r s w i t h s u p e r i o r filters provide greater selectivity conductivity and strength. This selectivity. Bandpass cavities reject with minimum inser tion loss. allows Telewave cavities to handle all frequencies outside a narrow Multiple cavities can also provide up to 350 watts, depending on pass band. These cavities reduce a wider passband when required. insertion loss. transmitter sideband noise, and also protect receivers against desensitization. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar TWPC-1405 cavities cover 118- achieved by the use of a specially metals and alodined aluminum help 148 MHz. All cavities are tuned mac hined comp en s ator and prevent galvanic corrosion. Silver to specified frequencies prior to Invar rod. The pass frequency is plated tuners and beryllium copper shipping, and no further adjustments temperature stable from -30°C finger stock provide non-corrosive should be required. The positive to +70°C. Telewave Ground Loop low loss contact, and ensure reliable, locking mechanism allows for quick technology places the center long-term performance. field retuning if frequency changes conductor of each coupling loop at become necessary. DC ground potential for lightning These cavities also feature calibrated protection and noise reduction. adjustable coupling, and insertion Heavy duty materials are used loss can be easily set from 0.5 dB to throughout each cavity to insure 2 dB or more to improve selectivity. high performance and long life. This allows cavity response to Cavity top plates are machined 108 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5021 Rev. 12/06 TWPC-1405-1, 2, 3 118 - 148 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 Figure 3 TWPC-1405-1 SINGLE 0 TWPC-1405-2 DUAL 0 TWPC-1405-3 TRIPLE 0 10 20 0.5 dB 1.0 dB 30 2.0 dB 40 50 60 70 -4 -2 Fc +2 +4 10 20 30 40 1.0 dB 50 2.0 dB 60 70 4.0 dB -4 -2 Fo +2 +4 Frequency (MHz) 10 20 30 40 50 60 1.5 dB 70 3.0 dB 6.0 dB -4 -2 Fo +2 +4 MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-1405-1 0.5 to 2.0 dB See figure 1 5 x 35 (13 x 89) 6 (2.7) 9 (4.1) TWPC-1405-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 35 (13 x 48 x 89) 12.5 (5.7) 15.5 (7) TWPC-1405-3 1.5 to 6.0 dB See figure 3 5.25 x 19 x 35 (13 x 48 x 89) 20 (9.1) 23 (10.4) 118-148 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 5 x 30 (13 x 76) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5021 Rev. 12/06 109 TWPC-1408-1, 2 BANDPASS CAVITIES 118 - 148 MHz TWPC-1408-1 TWPC-1408-2 T he Telew ave T WPC-14 0 8 -1 response to be optimized for any from ¼-inch aluminum, and are and 1408 -2 are 8" diameter, operating environment. At densely heliarc welded to the cavity body at ¼-wavelength, high "Q" bandpass populated sites, the 1408-2 cavity the high current point for improved c a v i t y f i l t e r s w i t h s u p e r i o r filters provide greater selectivity conductivity and strength. This selectivity. Bandpass cavities reject with minimum inser tion loss. allows Telewave cavities to handle all frequencies outside a narrow Multiple cavities can also provide up to 350 watts, depending on pass band. These cavities reduce a wider passband when required. insertion loss. transmitter sideband noise, and also protect receivers against desensitization. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar TWPC-1408 cavities cover 118- achieved by the use of a specially metals and alodined aluminum help 148 MHz. All cavities are tuned mac hined comp en s ator and prevent galvanic corrosion. Silver to specified frequencies prior to Invar rod. The pass frequency is plated tuners and beryllium copper shipping, and no further adjustments temperature stable from -30°C finger stock provide non-corrosive should be required. The positive to +70°C. Telewave Ground Loop low loss contact, and ensure reliable, locking mechanism allows for quick technology places the center long-term performance. field retuning if frequency changes conductor of each coupling loop at become necessary. DC ground potential for lightning T h e s e c av i t i e s a l s o f e a t u r e protection and noise reduction. calibrated adjustable coupling, and Heavy duty materials are used insertion loss can be easily set from throughout each cavity to insure 0.5 dB to 2 dB or more to improve high performance and long life. selectivity. This allows cavity Cavity top plates are machined 110 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5031 Rev. 12/06 CAVITIES & FILTERS TWPC-1408-1, 2 118 - 148 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 TWPC-1408-1 SINGLE 0 Figure 2 TWPC-1408-2 DUAL 0 10 10 20 0.5 dB 1.0 dB 30 2.0 dB 40 50 20 30 40 1.0 dB 50 60 60 2.0 dB 70 70 4.0 dB 80 80 -3 -2 -1 Fo +1 +2 +3 -3 -2 -1 Fo +1 +2 +3 Frequency (MHz) MODEL TWPC-1408-1 TWPC-1408-2 Insertion loss (adjustable) 0.5 to 2.0 dB 1.0 to 4.0 dB Attenuation See figure 1 See figure 2 Maximum dimensions with tuners extended in. (cm) 8 x 36 (25 x 91) 8.25 x 19 x 36 (25 x 48 x 91) Net weight lb. (kg) 8.5 (3.9) 19 (8.6) Shipping weight lb. (kg) 13 (5.9) 22 (10) COMMON SPECIFICATIONS Tuning frequency range 118-148 MHz Nominal impedance 50 ohms VSWR at resonance (max) 1.5:1 Input power (max) vs. insertion loss 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts Temperature range -30°C to +70°C Cavity electrical length ¼ wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 8 x 30 (20 x 76) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5031 Rev. 12/06 111 TWPC-1410-1, -2 BANDPASS CAVITIES 118 - 148 MHz TWPC-1410-1 TWPC-1410-2 T h e Te l ew ave T W PC-1410 -1 0.5 dB to 2 dB or more to improve Heavy duty materials are used and 1410-2 are 10" diameter, selec tivity. This allows cavity throughout each cavity to insure ¼-wavelength, high "Q" bandpass response to be optimized for any high performance and long life. c a v i t y f i l t e r s w i t h s u p e r i o r operating environment. At densely Cavity top plates are machined selectivity. Bandpass cavities reject populated sites, the 1410-2 cavity from ¼-inch aluminum, and are all frequencies outside a narrow filters provide greater selectivity heliarc welded to the cavity body at pass band. These cavities reduce with minimum inser tion loss. the high current point for improved transmitter sideband noise, and Multiple cavities can also provide conductivity and strength. This also protect receivers against a wider passband when required. allows Telewave cavities to handle desensitization. Mounting rails are provided for all up to 350 watts, depending on TWPC-1410 cavities cover 118- multiple-cavity filters. insertion loss. 148 MHz. All cavities are tuned Excellent frequency stability is Rigid foam inserts support the to specified frequencies prior to achieved by the use of a specially tuner assembly allowing vertical shipping, and no further adjustments mac hined comp en s ator and or horizontal mounting. Similar should be required. The positive Invar rod. The pass frequency is metals and alodined aluminum help locking mechanism allows for quick temperature stable from -30°C prevent galvanic corrosion. Silver field retuning if frequency changes to +70°C. Telewave Ground Loop plated tuners and beryllium copper become necessary. technology places the center finger stock provide non-corrosive These cavities also feature calibrated adjustable coupling, and insertion loss can be easily set from conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. low loss contact, and ensure reliable, long-term performance. 112 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5005 Rev. 12/06 CAVITIES & FILTERS TWPC-1410-1, -2 118 - 148 MHz 5 Attenuation in dB Figure 1 0 TYPICAL SELECTIVITY CHARACTERISTICS TWPC-1410-1 SINGLE Figure 2 TWPC-1410-2 DUAL 0 10 10 20 0.5 dB 20 30 1.0 dB 30 2.0 dB 40 40 50 50 1.0 dB 60 60 2.0 dB 70 70 4.0 dB 80 80 -3 -2 -1 Fo +1 +2 +3 -3 -2 -1 Fo +1 +2 +3 Frequency (MHz) MODEL TWPC-1410-1 TWPC-1410-2 Insertion loss (adjustable) 0.5 to 2.0 dB 1.0 to 4.0 dB Attenuation See figure 1 See figure 2 Maximum dimensions with tuners extended in. (cm) 10 x 32 (26 x 81) 10.25 x 20 x 32 (26 x 51 x 81.3) Net weight lb. (kg) 11 (5) 22 (10) Shipping weight lb. (kg) 14 (6.4) 28 (12.8) COMMON SPECIFICATIONS Tuning frequency range 118-148 MHz Nominal impedance 50 ohms VSWR at resonance (max) 1.5:1 Input power (max) vs. insertion loss 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts Temperature range -30°C to +70°C Cavity electrical length ¼ wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 10 x 30 (26 x 76) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5005 Rev. 12/06 113 TPRC-1405-1,2 PASS/REJECT CAVITIES 118 - 148 MHz TPRC-1405-1 TPRC-1405-2 T h e Te l e w a v e T PR C -14 0 5 -1 loss can be easily set from 0.5 dB to Heavy duty materials are used and 1405 -2 are 5" diameter, 2 dB or more to improve selectivity. throughout each cavity to insure ¼-wavelength Pass-Reject cavities This allows cavity response to high performance and long life. with an adjustable coupling loop be optimized for any operating Cavity top plates are machined and tuning capacitor. Pass-Reject environment. At densely populated from ¼-inch aluminum, and are cavities reject all frequencies sites, the TPRC-1405-2 dual cavity heliarc welded to the cavity body at outside a narrow pass band, with filter provides greater selectivity the high current point for improved a tunable notch for additional with minimum insertion loss. conductivity and strength. This protection with close spacing. Multiple cavities can also provide allows Telewave cavities to handle These cavities are commonly used a wider passband when required. up to 350 watts, depending on to reduce transmitter sideband Mounting rails are provided for all insertion loss. noise, and protect receivers against desensitization. multiple-cavity filters. Excellent frequency stability is Rigid foam inserts support the tuner assembly allowing vertical TPRC-1405 cavities cover 118- achieved by the use of a specially or horizontal mounting. Similar 148 MHz. All cavities are tuned machined compensator and Invar metals and alodined aluminum help to specified frequencies prior to rod. The pass and reject frequencies prevent galvanic corrosion. Silver shipping, and no further adjustments are temperature stable from -30°C plated tuners and beryllium copper should be required. The positive to +70°C. Telewave Ground Loop finger stock provide non-corrosive locking mechanism allows for quick technology places the center low loss contact, and ensure reliable, field re-tuning if frequency changes conductor of each coupling loop at long-term performance. become necessary. DC ground potential for lightning These cavities feature calibrated protection and noise reduction. adjustable coupling, and insertion 114 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5020 Rev. 12/06 CAVITIES & FILTERS TPRC-1405-1,2 118 - 148 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 - Single, 0.5 dB ins. loss 0 Figure 2 - Dual, 1 dB ins. loss 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 -1.0 -0.5 Fo +0.5 +1.0 +1.5 +2 +2.5 -1.0 -0.5 Fo +0.5 +1.0 +1.5 +2 +2.5 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TPRC-1405-1 0.5 to 2.0 dB See figure 1 5 x 35 (13 x 89) 6 (2.7) 9 (4.1) TPRC-1405-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 35 (13 x 48 x 89) 12.5 (5.7) 15.5 (7) 118-148 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 5 x 30 (13 x 76) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5020 Rev. 12/06 115 TWPC-1505-1, 2, 3 BANDPASS CAVITIES 148 - 174 MHz TWPC-1505-1 TWPC-1505-2 TWPC-1505-3 The Telewave TWPC-1505-1, 1505-2, cavity response to be optimized Cavity top plates are machined and 1505 -3 are 5" diameter, for any operating environment. At from ¼-inch aluminum, and are ¼-wavelength, high "Q" bandpass densely populated sites, the 1505-2 heliarc welded to the cavity body at c a v i t y f i l t e r s w i t h s u p e r i o r and 1505-3 cavity filters provide the high current point for improved selectivity. Bandpass cavities reject greater selectivity with minimum conductivity and strength. This all frequencies outside a narrow insertion loss. Multiple cavities allows Telewave cavities to handle pass band. These cavities reduce can also provide a wider passband up to 350 watts, depending on transmitter sideband noise, and when required. Mounting rails are insertion loss. also protect receivers against desensitization. provided for all multiple-cavity filters. Rigid foam inserts support the tuner assembly allowing vertical TWPC-1505 cavities cover 148- Excellent frequency stability is or horizontal mounting. Similar 174 MHz. All cavities are tuned achieved by the use of a specially metals and alodined aluminum help to specified frequencies prior to mac hined comp en s ator and prevent galvanic corrosion. Silver shipping, and no further adjustments Invar rod. The pass frequency is plated tuners and beryllium copper should be required. The positive temperature stable from -30°C finger stock provide non-corrosive locking mechanism allows for quick to +70°C. Telewave Ground Loop low loss contact, and ensure reliable, field retuning if frequency changes technology places the center long-term performance. become necessary. conductor of each coupling loop at These cavities also feature calibrated adjustable coupling, DC ground potential for lightning protection and noise reduction. and insertion loss can be easily Heavy duty materials are used set from 0.5 dB to 2 dB or more throughout each cavity to insure to improve selectivity. This allows high performance and long life. 116 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5012 Rev. 12/06 TWPC-1505-1, 2, 3 148 - 174 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 0 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 Figure 3 0 10 10 10 20 0.5 dB 20 20 1.0 dB 30 2.0 dB 30 30 40 40 1.0 dB 40 50 60 70 -4 -2 Fc +2 +4 50 2.0 dB 60 4.0 dB 70 -4 -2 Fc +2 +4 Frequency (MHz) 50 60 1.5 dB 70 3.0 dB 6.0 dB -4 -2 Fc +2 +4 MODEL TWPC-1505 TWPC-1505-2 TWPC-1505-3 Insertion loss (adjustable) 0.5 to 2.0 dB 1.0 to 4.0 dB 1.5 to 6.0 dB Attenuation See figure 1 See figure 2 See figure 3 Maximum dimensions with tuners extended in. (cm) 5 x 28 (13 x 71) 5.25 x 19 x 28 (13 x 48 x 71) 5.25 x 19 x 28 (13 x 48 x 71) Net weight lb. (kg) 5 (2.3) 11 (5) 15 (7) Shipping weight lb. (kg) 8 (3.6) 14 (6.5) 18 (8.1) COMMON SPECIFICATIONS Tuning frequency range 148-174 MHz Nominal impedance 50 ohms VSWR at resonance (max) 1.5:1 Input power (max) vs. insertion loss 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts Temperature range -30°C to +70°C Cavity electrical length ¼ wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 5 x 23.5 (13 x 60) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5012 Rev. 12/06 117 TWPC-1508-1, 2 BANDPASS CAVITIES 148 - 174 MHz TWPC-1508-1 TWPC-1508-2 T he Telew ave T WPC-150 8 -1 response to be optimized for any from ¼-inch aluminum, and are and 1508 -2 are 8" diameter, operating environment. At densely heliarc welded to the cavity body at ¼-wavelength, high "Q" bandpass populated sites, the 1508-2 cavity the high current point for improved c a v i t y f i l t e r s w i t h s u p e r i o r filters provide greater selectivity conductivity and strength. This selectivity. Bandpass cavities reject with minimum inser tion loss. allows Telewave cavities to handle all frequencies outside a narrow Multiple cavities can also provide up to 350 watts, depending on pass band. These cavities reduce a wider passband when required. insertion loss. transmitter sideband noise, and also protect receivers against desensitization. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar TWPC-1508 cavities cover 148- achieved by the use of a specially metals and alodined aluminum help 174 MHz. All cavities are tuned mac hined comp en s ator and prevent galvanic corrosion. Silver to specified frequencies prior to Invar rod. The pass frequency is plated tuners and beryllium copper shipping, and no further adjustments temperature stable from -30°C finger stock provide non-corrosive should be required. The positive to +70°C. Telewave Ground Loop low loss contact, and ensure reliable, locking mechanism allows for quick technology places the center long-term performance. field retuning if frequency changes conductor of each coupling loop at become necessary. DC ground potential for lightning T h e s e c av i t i e s a l s o f e a t u r e protection and noise reduction. calibrated adjustable coupling, and Heavy duty materials are used insertion loss can be easily set from throughout each cavity to insure 0.5 dB to 2 dB or more to improve high performance and long life. selectivity. This allows cavity Cavity top plates are machined 118 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5013 Rev. 12/06 TWPC-1508-1, 2 148 - 174 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 0 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 10 10 20 0.5 dB 1.0 dB 30 2.0 dB 40 50 20 30 40 1.0 dB 50 60 60 2.0 dB 70 70 4.0 dB 80 80 -3 -2 -1 Fc +1 +2 +3 Frequency (MHz) -3 -2 -1 Fc +1 +2 +3 MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-1508-1 0.5 to 2.0 dB See figure 1 8 x 28 (20.3 x 71) 7.5 (3.4) 11 (5) TWPC-1508-2 1.0 to 4.0 dB See figure 2 8.25 x 19 x 28 (20.3 x 48 x 71) 17 (7.7) 20 (9.1) 148-174 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 8 x 23.5 (20 x 60) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5013 Rev. 12/06 119 TWPC-1510-1, 2 BANDPASS CAVITIES 148 - 174 MHz TWPC-1510-1 TWPC-1510-2 T h e Te l ew ave T W PC-1510 -1 0.5 dB to 2 dB or more to improve Heavy duty materials are used and 1510-2 are 10" diameter, selec tivity. This allows cavity throughout each cavity to insure ¼-wavelength, high "Q" bandpass response to be optimized for any high performance and long life. c a v i t y f i l t e r s w i t h s u p e r i o r operating environment. At densely Cavity top plates are machined selectivity. Bandpass cavities reject populated sites, the 1510-2 cavity from ¼-inch aluminum, and are all frequencies outside a narrow filters provide greater selectivity heliarc welded to the cavity body at pass band. These cavities reduce with minimum inser tion loss. the high current point for improved transmitter sideband noise, and Multiple cavities can also provide conductivity and strength. This also protect receivers against a wider passband when required. allows Telewave cavities to handle desensitization. Mounting rails are provided for all up to 350 watts, depending on TWPC-1510 cavities cover 148- multiple-cavity filters. insertion loss. 174 MHz. All cavities are tuned Excellent frequency stability is Rigid foam inserts support the to specified frequencies prior to achieved by the use of a specially tuner assembly allowing vertical shipping, and no further adjustments mac hined comp en s ator and or horizontal mounting. Similar should be required. The positive Invar rod. The pass frequency is metals and alodined aluminum help locking mechanism allows for quick temperature stable from -30°C prevent galvanic corrosion. Silver field retuning if frequency changes to +70°C. Telewave Ground Loop plated tuners and beryllium copper become necessary. technology places the center finger stock provide non-corrosive These cavities also feature calibrated adjustable coupling, and insertion loss can be easily set from conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. low loss contact, and ensure reliable, long-term performance. 120 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5006 Rev. 10/08 CAVITIES & FILTERS TWPC-1510-1, 2 148 - 174 MHz 5 Attenuation in dB Figure 1 0 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 10 10 20 20 0.5 dB 30 1.0 dB 30 2.0 dB 40 40 50 50 1.0 dB 60 60 2.0 dB 70 70 4.0 dB 80 80 -3 -2 -1 Fc +1 +2 +3 -3 -2 -1 Fc +1 +2 +3 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-1510-1 0.5 to 2.0 dB See figure 1 10 x 28 (25 x 71) 10 (4.6) 13 (6) TWPC-1510-2 1.0 to 4.0 dB See figure 2 10.25 x 20 x 28 (50 x 48 x 71) 21.5 (9.8) 24 (10.9) 148-174 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 10 x 23.5 (25 x 60) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5006 Rev. 10/08 121 TPRC-1505-1,2 PASS-REJECT CAVITIES 148 - 174 MHz TPRC-1505-1 TPRC-1505-2 T h e Te l e w a v e T PR C -15 0 5 -1 to 2 dB or more to improve selec- high performance and long life. and 1505 -2 are 5" diameter, tivity. This allows cavity response Cavity top plates are machined ¼-wavelength Pass-Reject cavities to be optimized for any operat- from ¼-inch aluminum, and are he- with an adjustable coupling loop ing environment. At densely pop- liarc welded to the cavity body at and tuning capacitor. Pass-Reject ulated sites, the TPRC-1505-2 dual the high current point for improved cavities reject all frequencies out- cavity filter provides greater selec- conductivity and strength. This side a narrow pass band, with a tun- tivity with minimum insertion loss. allows Telewave cavities to handle able notch for additional protection Multiple cavities can also provide up to 350 watts, depending on in- with close spacing. These cavities a wider passband when required. sertion loss. are commonly used to reduce transmitter sideband noise, and protect receivers against desensitization. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar metals and TPRC-1505 cavities cover 148-174 achieved by the use of a specially alodined aluminum help prevent MHz. All cavities are tuned to spec- machined compensator and Invar galvanic corrosion. Silver plated ified frequencies prior to shipping, rod. The pass and reject frequen- tuners and beryllium copper finger and no further adjustments should cies are temperature stable from stock provide non-corrosive low be required. The positive locking -30°C to +70°C. Telewave Ground loss contact, and ensure reliable, mechanism allows for quick field Loop technology places the center long-term performance. re-tuning if frequency changes conductor of each coupling loop at become necessary. DC ground potential for lightning These cavities feature calibrated protection and noise reduction. adjustable coupling, and insertion Heavy duty materials are used loss can be easily set from 0.5 dB throughout each cavity to insure 122 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5024 Rev. 12/06 TPRC-1505-1,2 148 - 174 MHz 5 CAVITIES & FILTERS Attenuation in dB TPRC-1505-1 0 10 20 30 40 50 60 70 80 TYPICAL SELECTIVITY CHARACTERISTICS TPRC-1505-2 0 10 20 30 40 50 60 70 80 -1.0 -0.5 Fc +0.5 +1.0 +1.5 +2.0 +2.5 Frequency (MHz) -1.0 -0.5 Fo +.05 +1.0 +1.5 +2 +2.5 MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TPRC-1505-1 0.5 to 2.0 dB See figure 1 5 x 28 (13 x 71) 5 (2.3) 8 (3.6) TPRC-1505-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 28 (13 x 48 x 71) 11 (5) 14 (6.5) 148-174 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C 1/4 wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 5 x 23.5 (13 x 60) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5024 Rev. 12/06 123 TWNC-1505-1,2 NOTCH CAVITIES 148 - 174 MHz TWNC-1505-1 TWNC-1505-2 The Telewave T WNC-1505 -1 selectivity. This allows cavity Cavity top plates are machined and 1505 -2 are 5" diameter, response to be optimized for from ¼-inch aluminum, and are ¼-wavelength notch cavities with any operating environment. At heliarc welded to the cavity body at an adjustable coupling loop. Notch densely populated sites, the the high current point for improved cavities are typically used together TWNC-1505-2 dual cavity filter conductivity and strength. This with Pass or Pass/Reject cavities to provides greater selectivity with allows Telewave cavities to handle eliminate a particular frequency. minimum insertion loss. Multiple up to 350 watts, depending on Notch cavities have very low loss cavities can also provide a wider insertion loss. outside the notch band. Telewave can also "tilt" the notch response to move a notch very close to a pass frequency without adversely affecting the pass response. notch when required. Mounting rails are provided for all multiplecavity filters. Excellent frequency stability is achieved by the use of a specially Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar metals and alodined aluminum help prevent galvanic corrosion. Silver TWNC-1505 cavities cover 148- machined compensator and Invar plated tuners and beryllium copper 174 MHz. All cavities are tuned rod. The pass and reject frequencies finger stock provide non-corrosive to specified frequencies prior to are temperature stable from -30°C low loss contact, and ensure reliable, shipping, and no further adjustments to +70°C. Telewave Ground Loop long-term performance. should be required. The positive technology places the center locking mechanism allows for quick conductor of each coupling loop at field re-tuning if frequency changes DC ground potential for lightning become necessary. protection and noise reduction. These cavities feature calibrated Heavy duty materials are used adjustable coupling, which can throughout each cavity to insure be easily changed to improve high performance and long life. 124 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5023 Rev. 10/08 CAVITIES & FILTERS TWNC-1505-1,2 148 - 174 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 TWNC-1505-1 0 Figure 2 TWNC-1505-2 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 -3 -2 -1 Fc +1 +2 +3 Frequency (MHz) -3 -2 -1 Fc +1 +2 +3 MODEL TWNC-1505-1 Insertion loss (max) 0.2 dB Attenuation at notch frequency See figure 1 Maximum dimensions with tuners extended in. (cm) 5 x 28 (13 x 71) Net weight lb. (kg) 5 (2.3) Shipping weight lb. (kg) 8 (3.6) COMMON SPECIFICATIONS Tuning frequency range 148-174 MHz Nominal impedance 50 ohms VSWR at resonance (max) 1.5:1 Input power (max) 350 watts Temperature range -30°C to +70°C Cavity electrical length ¼ wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 5 x 23.5 (13 x 60) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com TWNC-1505-2 0.4 dB See figure 2 5.25 x 19 x 28 (13 x 48 x 71) 11 (5) 14 (6.5) All specifications subject to change without notice TWDS-5023 Rev. 10/08 125 TWPC-2205-1,2,3 BANDPASS CAVITY 200 - 300 MHz TWPC-2205-1 TWPC-2205-2 TWPC-2205-3 The Telewave TWPC-2205-1, 2205- cavity response to be optimized Cavity top plates are machined 2, and 2205-3 are 5" diameter, for any operating environment. At from ¼-inch aluminum, and are ¼-wavelength, high "Q" bandpass densely populated sites, the 2205-2 heliarc welded to the cavity body at c a v i t y f i l t e r s w i t h s u p e r i o r and 2205-3 cavity filters provide the high current point for improved selectivity. Bandpass cavities reject greater selectivity with minimum conductivity and strength. This all frequencies outside a narrow insertion loss. Multiple cavities allows Telewave cavities to handle pass band. These cavities reduce can also provide a wider passband up to 350 watts, depending on transmitter sideband noise, and when required. Mounting rails are insertion loss. also protect receivers against desensitization. provided for all multiple-cavity filters. Rigid foam inserts support the tuner assembly allowing vertical TWPC-2205 cavities cover 200- Excellent frequency stability is or horizontal mounting. Similar 300 MHz. All cavities are tuned achieved by the use of a specially metals and alodined aluminum help to specified frequencies prior to mac hined comp en s ator and prevent galvanic corrosion. Silver shipping, and no further adjustments Invar rod. The pass frequency is plated tuners and beryllium copper should be required. The positive temperature stable from -30°C finger stock provide non-corrosive locking mechanism allows for quick to +70°C. Telewave Ground Loop low loss contact, and ensure reliable, field retuning if frequency changes technology places the center long-term performance. become necessary. conductor of each coupling loop at These cavities also feature calibrated adjustable coupling, DC ground potential for lightning protection and noise reduction. and insertion loss can be easily Heavy duty materials are used set from 0.5 dB to 2 dB or more throughout each cavity to insure to improve selectivity. This allows high performance and long life. 126 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5014 Rev. 12/06 TWPC-2205-1,2,3 200 - 300 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 0 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 Figure 3 0 10 10 10 20 0.5 dB 30 1.0 dB 2.0 dB 40 50 60 70 -4 -2 Fc +2 +4 20 30 40 1.0 dB 50 2.0 dB 60 70 4.0 dB -4 -2 Fc +2 +4 Frequency (MHz) 20 30 40 50 60 70 1.5 dB 3.0 dB 6.0 dB -4 -2 Fc +2 +4 MODEL TWPC-2205-1 TWPC-2205-2 TWPC-2205-3 Insertion loss (adjustable) 0.5 to 2.0 dB 1.0 to 4.0 dB 1.5 to 6.0 dB Attenuation See figure 1 See figure 2 See figure 3 Maximum dimensions with tuners extended in. (cm) 5 x 24 (13 x 61) 5.25 x 19 x 24 (13 x 48 x 61) 5.25 x 19 x 24 (13 x 48 x 61) Net weight lb. (kg) 3 (1.5) 11.5 (5.3) 15 (6.8) Shipping weight lb. (kg) 7 (3.2) 15 (6.8) 19 (8.6) COMMON SPECIFICATIONS Tuning frequency range 200-300 MHz Nominal impedance 50 ohms VSWR at resonance (max) 1.5:1 Input power (max) vs. insertion loss 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts Temperature range -30°C to +70°C Cavity electrical length ¼ wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 5 x 18 (13 x 46) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5014 Rev. 12/06 127 TWPC-2208-1, 2 BANDPASS CAVITIES 200 - 300 MHz TWPC-2208-1 TWPC-2208-2 The Telewave T WPC-220 8 -1 response to be optimized for any from ¼-inch aluminum, and are and 2208 -2 are 8" diameter, operating environment. At densely heliarc welded to the cavity body at ¼-wavelength, high "Q" bandpass populated sites, the 2208-2 cavity the high current point for improved c a v i t y f i l t e r s w i t h s u p e r i o r filters provide greater selectivity conductivity and strength. This selectivity. Bandpass cavities reject with minimum inser tion loss. allows Telewave cavities to handle all frequencies outside a narrow Multiple cavities can also provide up to 350 watts, depending on pass band. These cavities reduce a wider passband when required. insertion loss. transmitter sideband noise, and also protect receivers against desensitization. Mounting rails are provided for all multiple-cavity filters. Excellent frequency stability is Rigid foam inserts support the tuner assembly allowing vertical or horizontal mounting. Similar TWPC-2208 cavities cover 200- achieved by the use of a specially metals and alodined aluminum help 300 MHz. All cavities are tuned mac hined comp en s ator and prevent galvanic corrosion. Silver to specified frequencies prior to Invar rod. The pass frequency is plated tuners and beryllium copper shipping, and no further adjustments temperature stable from -30°C finger stock provide non-corrosive should be required. The positive to +70°C. Telewave Ground Loop low loss contact, and ensure reliable, locking mechanism allows for quick technology places the center long-term performance. field retuning if frequency changes conductor of each coupling loop at become necessary. DC ground potential for lightning T h e s e c av i t i e s a l s o f e a t u r e protection and noise reduction. calibrated adjustable coupling, and Heavy duty materials are used insertion loss can be easily set from throughout each cavity to insure 0.5 dB to 2 dB or more to improve high performance and long life. selectivity. This allows cavity Cavity top plates are machined 128 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5015 Rev. 12/06 CAVITIES & FILTERS TWPC-2208-1, 2 200 - 300 MHz 5 Attenuation in dB Figure 1 0 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 10 10 20 0.5 dB 20 1.0 dB 30 30 2.0 dB 40 40 50 50 1.0 dB 60 60 2.0 dB 70 70 4.0 dB 80 80 -3 -2 -1 Fc +1 +2 +3 -3 -2 -1 Fc +1 +2 +3 Frequency (MHz) MODEL TWPC-2208-1 TWPC-2208-2 Insertion loss (adjustable) 0.5 to 2.0 dB 1.0 to 4.0 dB Attenuation See figure 1 See figure 2 Maximum dimensions with tuners extended in. (cm) 8 x 22 (25 x 56) 8.25 x 19 x 22 (25 x 48 x 56) Net weight lb. (kg) 7 (3.2) 15 (6.8) Shipping weight lb. (kg) 9 (4.1) 19 (8.6) COMMON SPECIFICATIONS Tuning frequency range 200-300 MHz Nominal impedance 50 ohms VSWR at resonance (max) 1.5:1 Input power (max) vs. insertion loss 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts Temperature range -30°C to +70°C Cavity electrical length ¼ wavelength Outer conductor, end plates 6061-T6 aluminum Inner conductor, coupling loops Silver plated copper Tuning rod Invar Contactors, fingerstock Beryllium copper Cavity dimensions (Diam. x H) in. (cm) 8 x 18 (20 x 46) Connectors N or UHF female (opt.) Finish Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5015 Rev. 12/06 129 TWPC-3505-1,2,3 BANDPASS CAVITY 300 - 400 MHz TWPC-3505-1 TWPC-3505-2 TWPC-3505-3 The Telewave TWPC-3505-1, 3505- set from 0.5 dB to 2 dB or more DC ground potential for lightning 2, and 3505-3 are 5" diameter, to improve selectivity. This allows protection and noise reduction. ¼-wavelength, high "Q" bandpass cavity filters with superior selectivity. Bandpass cavities reject all frequencies outside a narrow pass band. These cavities reduce transmitter sideband noise, and also protect receivers against desensitization. TWPC-3505 cavities cover 300400 MHz. All cavities are tuned cavity response to be optimized for any operating environment. At densely populated sites, the 3505-2 and 3505-3 cavity filters provide greater selectivity with minimum insertion loss. Multiple cavities can also provide a wider passband when required. Mounting rails are provided for all multiple-cavity filters. Heavy duty materials are used throughout each cavity to insure high performance and long life. Cavity top plates are machined from ¼-inch aluminum, and are heliarc welded to the cavity body at the high current point for improved conductivity and strength. This allows Telewave cavities to handle up to 350 watts, depending on to specified frequencies prior to Excellent frequency stability is insertion loss. shipping, and no further adjustments should be required. The positive locking mechanism allows for quick field retuning if frequency changes become necessary. These cavities also feature calibrated adjustable coupling, achieved by the use of a specially machined compensator and Invar rod. The pass frequency is temperature stable from -30°C to +70°C. Telewave Ground Loop technology places the center conductor of each coupling loop at Similar metals and alodined aluminum help prevent galvanic corrosion. Silver plated tuners and beryllium copper finger stock provide non-corrosive low loss contact, and ensure reliable, longterm performance. and insertion loss can be easily 130 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5022 Rev. 8/09 TWPC-3505-1,2,3 300 - 400 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 0 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 Figure 3 0 10 10 10 20 0.5 dB 20 20 30 1.0 dB 30 30 2.0 dB 40 40 1.0 dB 40 50 60 70 -4 -2 Fc +2 +4 50 2.0 dB 60 4.0 dB 70 -4 -2 Fc +2 +4 Frequency (MHz) 50 60 70 1.5 dB 3.0 dB 6.0 dB -4 -2 Fc +2 +4 MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-3505-1 0.5 to 2.0 dB See figure 1 5 x 24 (13 x 61) 3 (1.5) 7 (3.2) TWPC-3505-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 24 (13 x 48 x 61) 11.5 (5.3) 15 (6.8) TWPC-3505-3 1.5 to 6.0 dB See figure 3 5.25 x 19 x 24 (13 x 48 x 61) 15 (6.8) 19 (8.6) 300-400 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 5 x 18 (13 x 46) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5022 Rev. 8/09 131 TWPC-4504-1, 2, 3 BANDPASS CAVITIES 400 - 512 MHz TWPC-4504-1 TWPC-4504-3 TWPC-4504-2 The Telewave TWPC-4504-1, 4504-2, to 4 dB to improve selectivity. Heavy duty materials are used and 4504 -3 are 4" diameter, This allows cavity response to throughout each cavity to insure ¼-wavelength, high "Q" bandpass be optimized for any operating high performance and long life. c a v i t y f i l t e r s w i t h s u p e r i o r environment. At densely populated Cavity top plates are machined selectivity. Bandpass cavities reject sites, the 4504-2 and -3 cavity filters from ¼-inch aluminum, and are all frequencies outside a narrow provide greater selectivity with heliarc welded to the cavity body at pass band. These cavities reduce minimum insertion loss. Multiple the high current point for improved transmitter sideband noise, and cavities can also provide a wider conductivity and strength. This also protect receivers against passband when required. Up to allows Telewave cavities to handle desensitization. four 4" cavities can be mounted on up to 350 watts, depending on TWPC-4504 cavities cover 400- one 19" x 5.25" panel. insertion loss. 512 MHz. All cavities are tuned Excellent frequency stability is Similar metals and alodined to specified frequencies prior to achieved by the use of a specially aluminum help prevent galvanic shipping, and no further adjustments mac hined comp en s ator and corrosion. Silver plated tuners should be required. The positive Invar rod. The pass frequency is and beryllium copper finger stock locking mechanism allows for quick temperature stable from -30°C provide non-corrosive low loss field retuning if frequency changes to +70°C. Telewave Ground Loop contact, and ensure reliable, long- become necessary. technology places the center term performance. These cavities also feature calibrated adjustable coupling, and insertion loss can be easily set from 0.5 dB conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. 132 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5001 Rev. 10/13 TWPC-4504-1, 2, 3 400 - 512 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 0 10 0.5 dB 20 1.0 dB 2.0 dB 30 40 50 60 70 80 -6 -4 -2 Fo +2 +4 +6 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 10 20 30 1.0 dB 40 2.0 dB 50 60 4.0 dB 70 80 -6 -4 -2 Fc +2 +4 +6 Frequency (MHz) Figure 3 0 10 20 30 40 1.0 dB 50 60 2.0 dB 70 80 4.0 dB -6 -4 -2 Fc +2 +4 +6 MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-4504-1 0.5 to 2.0 dB See figure 1 4 x 8 (10 x 20) 3.3 (1.5) 7 (3.2) TWPC-4504-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 11 (13 x 48 x 28) 11.5 (5.25) 15 (6.8) TWPC-4504-3 1.0 to 4.0 dB See figure 3 5.25 x 19 x 11 (13 x 48 x 28) 14 (6.8) 19 (8.6) 400-512 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 4 x 8 (10 x 20) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5001 Rev. 10/13 133 TWPC-4505-1, 2, 3 BANDPASS CAVITIES - 3/4 WAVE 400 - 512 MHz TWPC-4505-1 TWPC-4505-2 TWPC-4505-3 The Telewave TWPC- 4505-1, 4505- cavity response to be optimized Cavity top plates are machined 2, and 4505-3 are 5" diameter, ¾ for any operating environment. At from ¼-inch aluminum, and are wavelength, high "Q" bandpass densely populated sites, the 4505-2 heliarc welded to the cavity body at c a v i t y f i l t e r s w i t h s u p e r i o r and 4505-3 cavity filters provide the high current point for improved selectivity. Bandpass cavities reject greater selectivity with minimum conductivity and strength. This all frequencies outside a narrow insertion loss. Multiple cavities allows Telewave cavities to handle pass band. These cavities reduce can also provide a wider passband up to 350 watts, depending on transmitter sideband noise, and when required. Mounting rails are insertion loss. also protect receivers against desensitization. provided for all multiple-cavity filters. Rigid foam inserts support the tuner assembly allowing vertical TWPC-4505 cavities cover 400- Excellent frequency stability is or horizontal mounting. Similar 512 MHz. All cavities are tuned achieved by the use of a specially metals and alodined aluminum help to specified frequencies prior to mac hined comp en s ator and prevent galvanic corrosion. Silver shipping, and no further adjustments Invar rod. The pass frequency is plated tuners and beryllium copper should be required. The positive temperature stable from -30°C finger stock provide non-corrosive locking mechanism allows for quick to +70°C. Telewave Ground Loop low loss contact, and ensure reliable, field retuning if frequency changes technology places the center long-term performance. become necessary. conductor of each coupling loop at These cavities also feature calibrated adjustable coupling, DC ground potential for lightning protection and noise reduction. and insertion loss can be easily Heavy duty materials are used set from 0.5 dB to 2 dB or more throughout each cavity to insure to improve selectivity. This allows high performance and long life. 134 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5018 Rev. 12/06 TWPC-4505-1, 2, 3 400 - 512 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 0 10 20 0.5 dB 1.0 dB 30 2.0 dB 40 50 60 70 -4 -2 Fc +2 +4 TYPICAL SELECTIVITY CHARACTERISTICS Figure 2 0 Figure 3 0 10 10 20 20 30 30 40 1.0 dB 50 2.0 dB 60 70 4.0 dB -4 -2 Fc +2 +4 Frequency (MHz) 40 50 60 1.5 dB 70 3.0 dB 6.0 dB -4 -2 Fc +2 +4 MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-4505-1 0.5 to 2.0 dB See figure 1 5 x 28 (13 x 71) 5 (2.3) 8 (3.6) TWPC-4505-2 1.0 to 4.0 dB See figure 2 5.25 x 19 x 28 (13 x 48 x 71) 11.5 (5.3) 14 (6.5) TWPC-4505-3 1.5 to 6.0 dB See figure 3 5.25 x 19 x 28 (13 x 48 x 71) 15 (6.8) 18 (8.1) 400-512 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¾ wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 5 x 23.5 (13 x 60) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5018 Rev. 12/06 135 TWPC-4510-1,2 BANDPASS CAVITY 400 - 512 MHz TWPC-4510-1 TWPC-4510-2 T he Telew ave T WPC- 4510 -1 0.5 dB to 2 dB or more to improve Heavy duty materials are used and 4510-2 are 10" diameter, selec tivity. This allows cavity throughout each cavity to insure ¼-wavelength, high "Q" bandpass response to be optimized for any high performance and long life. c a v i t y f i l t e r s w i t h s u p e r i o r operating environment. At densely Cavity top plates are machined selectivity. Bandpass cavities reject populated sites, the 4510-2 cavity from ¼-inch aluminum, and are all frequencies outside a narrow filter provides greater selectivity heliarc welded to the cavity body at pass band. These cavities reduce with minimum inser tion loss. the high current point for improved transmitter sideband noise, and Multiple cavities can also provide conductivity and strength. This also protect receivers against a wider passband when required. allows Telewave cavities to handle desensitization. Mounting rails are provided for all up to 350 watts, depending on TWPC-4510 cavities cover 400- multiple-cavity filters. insertion loss. 512 MHz. All cavities are tuned Excellent frequency stability is Similar metals and alodined to specified frequencies prior to achieved by the use of a specially aluminum help prevent galvanic shipping, and no further adjustments mac hined comp en s ator and corrosion. Silver plated tuners should be required. The positive Invar rod. The pass frequency is and beryllium copper finger stock locking mechanism allows for quick temperature stable from -30°C provide non-corrosive low loss field retuning if frequency changes to +70°C. Telewave Ground Loop contact, and ensure reliable, long- become necessary. technology places the center term performance. These cavities also feature calibrated adjustable coupling, and insertion loss can be easily set from conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. 136 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5017 Rev. 8/09 TWPC-4510-1,2 400 - 512 MHz 5 CAVITIES & FILTERS Attenuation in dB Figure 1 0 TYPICAL BANDPASS CAVITY RESPONSE CURVES Figure 2 0 10 10 20 0.5 dB 30 1.0 dB 40 3.0 dB 20 30 40 1.0 dB 0 100 200 300 400 KHz 50 50 2.0 dB 60 60 70 70 6.0 dB -4 -3 -2 -1 Fc +1 +2 +3 +4 -4 -3 -2 -1 Fo +1 +2 +3 +4 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation Maximum dimensions with tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Cavity dimensions (Diam. x H) in. (cm) Connectors Finish TWPC-4510-1 0.5 to 2.0 dB See figure 1 10 x 17 (25.4 x 43) 7.5 (3.4) 10 (4.5) TWPC-4510-2 1.0 to 4.0 dB See figure 2 10.25 x 20 x 17 (26 x 50.8 x 43) 17 (7.7) 22 (10) 400-512 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 6061-T6 aluminum Silver plated copper Invar Beryllium copper 10 x 12 (25.4 x 31) N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5017 Rev. 8/09 137 TWPC-7908-1, -2 BANDPASS CAVITY 776 - 825 MHz TWPC-7908-1 TWPC-7908-2 T h e Te l e w a v e T W P C -79 0 8 - 0.5 dB to 2 dB or more to improve Heavy duty materials are used 1 and 7908-2 are 8" diameter, selec tivity. This allows cavity throughout each cavity to insure ¼-wavelength, high "Q" bandpass response to be optimized for any high performance and long life. c a v i t y f i l t e r s w i t h s u p e r i o r operating environment. At densely Cavity top plates are machined selectivity. Bandpass cavities reject populated sites, the 7908-2 cavity from ¼-inch aluminum, and are all frequencies outside a narrow filter provides greater selectivity heliarc welded to the cavity body at pass band. These cavities reduce with minimum inser tion loss. the high current point for improved transmitter sideband noise, and Multiple cavities can also provide conductivity and strength. This also protect receivers against a wider passband when required. allows Telewave cavities to handle desensitization. Mounting rails are provided for all up to 350 watts, depending on TWPC-7908 cavities cover 776- multiple-cavity filters. insertion loss. 825 MHz. All cavities are tuned Excellent frequency stability is Similar metals and alodined to specified frequencies prior to achieved by the use of a specially aluminum help prevent galvanic shipping, and no further adjustments mac hined comp en s ator and corrosion. Silver plated tuners should be required. The positive Invar rod. The pass frequency is and beryllium copper finger stock locking mechanism allows for quick temperature stable from -30°C provide non-corrosive low loss field retuning if frequency changes to +70°C. Telewave Ground Loop contact, and ensure reliable, long- become necessary. technology places the center term performance. These cavities also feature calibrated adjustable coupling, and insertion loss can be easily set from conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. 138 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5028 Rev. 8/09 CAVITIES & FILTERS TWPC-7908-1, -2 776 - 825 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS 0 Figure 1 - TWPC-7908-1 at 790 MHz 0 Figure 2 - TWPC-7908-2 at 790 MHz 10 20 0.5 dB 1.0 dB 30 2.0 dB 40 10 20 30 40 1.0 dB 50 50 60 60 70 70 -6 -4 -2 Fc +2 +4 +6 -6 -4 -2 Fc +2 +4 +6 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation Max size - tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Cavity size (Diam. x H) in. (cm) Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Connectors Finish TWPC-7908-1 0.5 to 2.0 dB See figure 1 8 x 11.875 (20.3 x 30.1) 7 (3.2) 10 (4.5) TWPC-7908-2 1.0 to 4.0 dB See figure 2 8.25 x 19 x 15.375 (21 x 48.3 x 39.1) 17 (7.7) 22 (10) 776-825 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 8 x 11.875 (20.3 x 30.2) 6061-T6 aluminum Silver plated copper Invar Beryllium copper N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5028 Rev. 8/09 139 TWPC-8608-1,-2 BANDPASS CAVITIES 800 - 970 MHz TWPC-8608-1 TWPC-8608-2 The Telewave T WPC- 8608 -1 0.5 dB to 2 dB or more to improve Heavy duty materials are used and 8608 -2 are 8" diameter, selec tivity. This allows cavity throughout each cavity to insure ¼-wavelength, high "Q" bandpass response to be optimized for any high performance and long life. c a v i t y f i l t e r s w i t h s u p e r i o r operating environment. At densely Cavity top plates are machined selectivity. Bandpass cavities reject populated sites, the 8608-2 cavity from ¼-inch aluminum, and are all frequencies outside a narrow filter provides greater selectivity heliarc welded to the cavity body at pass band. These cavities reduce with minimum inser tion loss. the high current point for improved transmitter sideband noise, and Multiple cavities can also provide conductivity and strength. This also protect receivers against a wider passband when required. allows Telewave cavities to handle desensitization. Mounting rails are provided for all up to 350 watts, depending on TWPC-8608 cavities cover 800- multiple-cavity filters. insertion loss. 970 MHz. All cavities are tuned Excellent frequency stability is Similar metals and alodined to specified frequencies prior to achieved by the use of a specially aluminum help prevent galvanic shipping, and no further adjustments mac hined comp en s ator and corrosion. Silver plated tuners should be required. The positive Invar rod. The pass frequency is and beryllium copper finger stock locking mechanism allows for quick temperature stable from -30°C provide non-corrosive low loss field retuning if frequency changes to +70°C. Telewave Ground Loop contact, and ensure reliable, long- become necessary. technology places the center term performance. These cavities also feature calibrated adjustable coupling, and insertion loss can be easily set from conductor of each coupling loop at DC ground potential for lightning protection and noise reduction. 140 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5002 Rev. 8/09 CAVITIES & FILTERS TWPC-8608-1,-2 800 - 970 MHz 5 Attenuation in dB TYPICAL SELECTIVITY CHARACTERISTICS Figure 1 - TWPC-8608-1 at 860 MHz 0 Figure 2 - TWPC-8608-2 at 860 MHz 0 10 20 0.5 dB 1.0 dB 30 2.0 dB 40 10 20 30 40 1.0 dB 50 50 60 60 70 70 -6 -4 -2 Fc +2 +4 +6 -6 -4 -2 Fc +2 +4 +6 Frequency (MHz) MODEL Insertion loss (adjustable) Attenuation Max size - tuners extended in. (cm) Net weight lb. (kg) Shipping weight lb. (kg) COMMON SPECIFICATIONS Tuning frequency range Nominal impedance VSWR at resonance (max) Input power (max) vs. insertion loss Temperature range Cavity electrical length Cavity size (Diam. x H) in. (cm) Outer conductor, end plates Inner conductor, coupling loops Tuning rod Contactors, fingerstock Connectors Finish TWPC-8608-1 0.5 to 2.0 dB See figure 1 8 x 15.375 (20.3 x 39.1) 7 (3.2) 10 (4.5) TWPC-8608-2 1.0 to 4.0 dB See figure 2 8.25 x 19 x 15.375 (21 x 48.3 x 39.1) 17 (7.7) 22 (10) 800-970 MHz 50 ohms 1.5:1 0.5 dB - 350 watts, 1 dB - 250 watts, 2 dB - 150 watts -30°C to +70°C ¼ wavelength 8 x 11.875 (20.3 x 30.2) 6061-T6 aluminum Silver plated copper Invar Beryllium copper N or UHF female (opt.) Gray acrylic enamel NOTE: When ordering be sure to specify exact frequency and model number. Contact the factory if additional information or assistance is required. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5002 Rev. 8/09 141 40 - 960 MHz TLF-50, -90, -90H, 150, 450, 760, 860 LOWPASS FILTERS Telewave Lowpass Filters eliminate harmonics, spurs, and intermodulation products that may occur above the fundamental frequency of a transmitter. These devices feature extremely low insertion loss, and are designed to be installed in the transmission line continuously. The standard connector configuration is N Female to N Male. Other combinations are available, including 7-16 DIN (extra cost). TLF-50 Attenuation in dB TYPICAL RESPONSE CURVE - TLF-150 0 INSERTION LOSS 10 20 RETURN LOSS 30 40 50 60 70 80 REJECTION 1 144 174 288 348 400 150 300 Frequency (MHz) Perforated Cover TLF-90H SPECIFICATIONS TLF-50 TLF-90 TLF-90H TLF-150 TLF-450 TLF-760, 860 Frequency range (MHz) 40-54 88-108 88-108 144-174 406-512 763-824, 806-960 Impedance (nom.) 50 ohms VSWR (max) 1.3:1 Power (max) 200 W 200 W 1000 W 400 W 200 W 200 W Insertion loss 0.15 dB typ. / 0.25 dB max Rejection at 2Fc (typ) 30 dB 40 dB 35 dB 40 dB 50 dB 45 dB Dimensions (HWL) in. 1.25 x 1.5 x 4 1.625 x 2.5 x 4.5 1.25 x 1.5 x 4 Dimensions (HWL) cm 3.2 x 3.8 x 10.2 4.1 x 6.4 x 11.4 3.2 x 3.8 x 10.2 Weight lb. (kg) 0.5 (0.23) 1 (0.45) 0.5 (0.23) Connectors Standard configuration is N-F to N-M for inline use. Any combination of N, UHF, BNC, or 7-16 DIN male or female may be specified. (7-16 DIN is additional cost.) 142 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5038 Rev. 10/12 CAVITIES & FILTERS THF-150, 450, 760, 860 HIGHPASS FILTERS Telewave Highpass Filters eliminate spurs and noise that may occur below the fundamental frequency of a transmitter. They are also used to protect receivers from nearby high power transmitters. These devices feature extremely low insertion loss, and are designed to be installed in the transmission line continuously. The standard connector configuration is N Female to N Male. Other combinations are available, including 7-16 DIN (extra cost). Attenuation (dB) TYPICAL RESPONSE CURVE - THF-150 0 10 20 30 REJECTION 40 50 60 70 80 INSERTION LOSS RETURN LOSS 10 88 108 144 174 250 Frequency (MHz) 144 - 870 MHz 5 THF-150 SPECIFICATIONS Frequency range Impedance (nom.) VSWR (max) Power (typ.) Insertion loss Rejection (typ) at 1/2 Fc Dimensions (HWL) in. (cm) Weight lb. (kg) Connectors THF-150 THF-450 THF-760 THF-860 144-174 MHz 450-470 MHz 763-869 MHz 850-870 MHz 50 ohms 1.3:1 25 watts continuous / 50 watts intermittent - Contact Telewave for higher power 0.15 dB typ. / 0.25 dB max 50 dB 40 dB 10 dB 10 dB 1.25 x 1.5 x 4 (3.2 x 3.8 x 10.2) 0.5 (0.23) Standard configuration is N-F to N-M for inline use. Any combination of N, UHF, BNC, or 7-16 DIN male or female may be specified. (7-16 DIN is additional cost.) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5039 Rev. 10/12 143 Attenuation in dB TWX-50, 150 RECEIVER CRYSTAL FILTER Telewave Crystal Filters provide an extremely narrow bandpass for a single frequency, to protect a receiver from nearby transmitters and adjacent channel interference. This bandpass is much sharper than a typical high "Q" cavity filter. The combination of a crystal filter and a Telewave TLA or TGA series preamplifier can often rescue a receiver that has been impacted by an new adjacent transmitter, or allow implementation of a system with insufficient available frequency spacing. TYPICAL RESPONSE 10 20 30 40 50 60 70 -150 -50 Fc +50 +150 Frequency (KHz) 50 - 150 MHz TWX-50, 150 SIDE VIEW SPECIFICATIONS Frequency range Attenuation ± 30 KHz (min) Attenuation ± 50 KHz (min) Insertion loss (typ) Impedance / VSWR (max) Input level (max) Temperature Dimensions (HWL) in. (cm) Weight lb. (kg) TWX-50 TWX-150 36-88 MHz 138-174 MHz 20 dB 20 dB 50 dB 60 dB 4 dB 7 dB 50 ohms / 1.2:1 0 dBm -20° to +70° C 1 x 1 x 3.75 (2.5 x 2.5 x 9.5) 0.5 (0.23) 144 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-5037 Rev. 12/06 6 DUPLEXERS 6 DUPLEXERS Bandpass Bandpass duplexers allow only a narrow band of frequencies to reach the receiver or leave the transmitter. All other frequencies are rejected. These duplexers are the best available for crowded RF environments where transmit and receive frequencies have significant separation. Pass - Reject Pass / Reject duplexers offer a modified pass response for a narrow band of frequencies, and also provide a tunable notch which deepens the reject response at a particular frequency. This type of filter supports closer frequency spacing than a bandpass duplexer. Bandpass / Bandreject Bandpass / Bandreject duplexers provide a true bandpass for a group of transmitters and receivers, with a tunable notch which increases the reject response at a particular frequency. These duplexers can also combine two transmitters into one antenna. Compact Compact duplexers use specially designed Telewave square cavity filters. The size and form factor of these duplexers allows for more efficient use of rack space in many installations. Combline Combline duplexers offer wide bandpass and sharp skirts in a very compact package. The combline design also exhibits very low insertion loss and can handle up to 650 watts of power. Mobile Mobile duplexers are very compact devices which use helical resonators to provide a notchband response for a transmitter and receiver. They are ideally suited for limited space applications with one transmitter and one receiver. TPRD-0354, 0454 PASS / REJECT DUPLEXER 30 - 50 MHz 6 DUPLEXERS The Telewave TPRD-0354 and threaded Invar tuning rods assure TPRD-0454 allow the simultaneous maximum temperature stability, operation of a transmitter and higher "Q", and years of trouble receiver into a common antenna. free operation. These duplexers feature minimum insertion loss, and maximum isolation between transmitter and receiver. The Pass-Reject design combines a bandpass response with a tunable notch at 0 TYPICAL RESPONSE the RX frequency for improved performance at close spacing. 20 Attenuation in dB The superior construction of Telewave cavity duplexers allows better rejection of transmitter 40 spurious radiation, providing greater receiver protection. Selectivity and insertion loss 60 are fully adjustable by rotating the calibrated connector loops. 80 TX-RX Telewave cavities are manufactured with ¼" aluminum top plates, which are fully welded to the aluminum outer conductor. Silver plated tuners, beryllium copper finger stock contactors, and -0.4 -0.2 0 +0.2 +0.4 Frequency (MHz) ELECTRICAL SPECIFICATIONS Frequency coverage / tuning range Frequency separation (min) Maximum input power Insertion loss RX isolation / TX noise suppression VSWR (max) Temperature range MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Tuners fully extended in. (cm) Cavities Mounting Connectors Finish Net weight lb. (kg) TPRD-0354 TPRD-0454 30-40 MHz / ± 2.5 MHz 40-50 MHz / ± 2.5 MHz 600 KHz 350 watts 1.0 dB (TX / RX to ant.) 80 dB at ±600 KHz 1.5:1 30°C to +60°C 88 x 19 x 11 (224 x 48 x 28) 72 x 19 x 11 (183 x 48 x 28) 97 x 19 x 11 (246 x 48 x 28) 81 x 19 x 11 (206 x 48 x 28) (4) - 5" 19" Rack or wall mount N or UHF female (opt.) Gray acrylic enamel 65 (29.5) 51 (23.2) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6007 Rev. 10/08 147 TPRD-0384, 0484 PASS / REJECT DUPLEXER The Telewave TPRD-0384 and tuners, beryllium copper finger TPRD-0484 allow the simultaneous stock contactors, and threaded operation of a transmitter and Invar tuning rods assure maximum receiver into a common antenna. temperature stabilit y, higher These duplexers feature minimum "Q", and years of trouble free inser tion loss, and maximum operation. isolation between transmitter and receiver. The Pass-Reject design gives much better performance for close spacing than an equivalent bandpass duplexer. TYPICAL RESPONSE 0 Attenuation (dB) The superior construction of Telewave cavity duplexers allows 20 better rejection of transmitter spurious radiation, providing greater 40 receiver protection. Selectivity and insertion loss are fully adjustable by rotating the calibrated connector 60 loops. Telewave cavities are manufactured with ¼" aluminum top plates, which are fully welded to the aluminum outer conductor. Silver plated 80 -.2 0 +.2 +.4 Frequency (MHz) 30 - 50 MHz ELECTRICAL SPECIFICATIONS Frequency coverage / tuning range Frequency separation (min) Maximum input power Insertion loss RX isolation / TX noise suppression VSWR (max) Temperature range MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Tuners fully extended in. (cm) Cavities Mounting Connectors Finish Net weight lb. (kg) TPRD-0384 TPRD-0484 30-40 MHz / ± 2.5 MHz 40-50 MHz / ± 2.5 MHz 300 KHz 350 watts 1.0 dB (TX / RX to ant.) 80 dB at ±300 KHz 1.5:1 -30°C to +60°C 88 x 19 x 17 (224 x 48 x 43) 72 x 19 x 17 (183 x 49 x 43) 97 x 19 x 17 (246 x 48 x 43) 81 x 19 x 17 (206 x 48 x 43) (4) - 8" 19" Rack or wall mount N or UHF female (opt.) Gray acrylic enamel 105 (48) 86 (39) 148 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6016 Rev. 10/08 DUPLEXERS TPRD-0754 PASS / REJECT DUPLEXER The Telewave TPRD-0754 allows the simultaneous operation of a transmitter and receiver into a common antenna. This duplexer features minimum insertion loss, and maximum isolation between transmitter and receiver. The PassReject design gives much better performance for close spacing than an equivalent bandpass duplexer. tuners, beryllium copper finger stock contactors, and threaded Invar tuning rods assure maximum temperature stability, higher "Q", and years of trouble free operation. TYPICAL RESPONSE 0 The superior construction of Telewave cavity duplexers allows 20 better rejection of transmitter Attenuation (dB) spurious radiation, providing greater receiver protection. Selectivity and 40 insertion loss are fully adjustable by rotating the calibrated connector loops. 60 Telewave cavities are manufactured with ¼" aluminum top plates, which are fully welded to the aluminum outer conductor. Silver plated 80 -0.6 Fo +0.6 +1.2 Frequency (MHz) 66 - 88 MHz 6 ELECTRICAL SPECIFICATIONS Frequency coverage / tuning range Frequency separation (min) Maximum input power Insertion loss RX isolation / TX noise suppression VSWR (max) Temperature range MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Tuners fully extended in. (cm) Cavities Mounting Connectors Finish Net weight lb. (kg) 66-88 MHz 600 KHz 350 watts 1.2 dB (TX / RX to ant.) 80 dB at ±600 KHz 1.5:1 -30°C to +60°C 47 x 19 x 11 (119 x 48 x 28) 54 x 19 x 11 (137 x 48 x 28) (4) - 5" 19" Rack or wall mount N or UHF female (opt.) Gray acrylic enamel 40 (18.2) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6031 Rev. 11/12 149 TPRD-1084 PASS-REJECT BASE STATION DUPLEXER The Telewave TPRD-1084 Duplexer fully welded to the aluminum allows simultaneous operation of outer conductor. As a result of their a transmitter and receiver into a superior construction, Telewave 8" common antenna. This Pass-Reject cavity duplexers achieve greater duplexer is ideal for use in systems rejection of transmitter spurious and requiring maximum isolation, with noise radiation, providing better close frequency spacing down to receiver protection. Silver-plated 500 KHz. tuners, beryllium copper finger The TPRD-1084 duplexer has two pass-reject cavities each in the transmitter and receiver sections. Selectivity and stock contactors, and threaded Invar rods assure maximum temperature stability, higher "Q", and many years of trouble-free operation. insertion loss may be adjusted by rotating the calibrated connector loops. (See graphs for typical response curves). Telewave duplexers have ¼-inch aluminum top plates which are 88 - 108 MHz ELECTRICAL SPECIFICATIONS Tuning range 88-108 MHz Frequency separation (min) 500 KHz Maximum input power 300 watts Insertion loss TX / RX to ant. 1.5 dB VSWR (max) 1.5:1 Temperature range -30°C to +70°C RX isolation 80 dB at ±500 KHz TX noise suppression 80 dB at ±500 KHz MECHANICAL SPECIFICATIONS Cavities (4) - 8" Mounting 19" Rack or wall mount Connectors N or UHF female (opt.) Finish Gray acrylic enamel Net weight lb. (kg) 37 (16.8) Dimensions (HWD) in. (cm) 30 x 19 x 17 (76 x 48 x 43) Tuners fully extended in. (cm) 35 x 19 x 17 (89 x 48 x 43) Attenuation in dB TYPICAL RESPONSE CURVES (TPRD-1084) 0 10 20 30 40 50 60 70 80 -.75 -.50 -.25 0 +.25 +.50 Frequency (MHz) 150 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6008 Rev. 10/12 DUPLEXERS TPRD-1344C, 1344CM COMPACT PASS / REJECT DUPLEXER The TPRD-1344C and 1344CM produce high performance in a compact design for the 118136 MHz VHF Air band. These duplexers are only one-third of the size of earlier models, and deliver equivalent performance. The TPRD-1344C/CM produces 70 dB isolation at 600 KHz, with a 350 watt power rating, and insertion loss is 1.5 dB or less. Each duplexer fits a standard 19" rack, with rack height of 5.25" and 4" respectively. The TPRD-1344CM is supplied with adjustable mounting tabs for installation in a cabinet. 118 - 136 MHz 6 TPRD-1344C TYPICAL RESPONSE 0 20 Attenuation in dB 40 TPRD-1344CM ELECTRICAL SPECIFICATIONS Tuning range Frequency separation (min) Maximum input power Insertion loss TX/RX to ant. TX noise suppression at RX (typ) RX isolation at TX (typ) VSWR (max) Temperature range Cavities MECHANICAL SPECIFICATIONS Mounting Dimensions (HWD) in. (cm) (Tuners fully extended) Connectors Finish Net weight lb. (kg) 60 80 118-136 MHz 600 KHz 350 watts 1.5 dB 70 dB at 600 KHz 70 dB at 600 KHz 1.5:1 -30°C to +70°C (4) - 4" 1344C 1344CM 19" Rack 19" Cabinet 5.25 x 19 x 16 (13 x 48 x 41) 4 x 19 x 16 (10 x 48 x 41) N or UHF female (opt.) Gray acrylic enamel 21 (9.5) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 600 KHz All specifications subject to change without notice TWDS-6030 Rev. 10/12 151 135 - 151 MHz TPRD-1444C, 1444CM COMPACT PASS / REJECT DUPLEXER The TPRD-1444C and 1444CM produce high performance in a compact design for the 135-151 MHz VHF band. These duplexers are only one-third of the size of earlier models, and deliver equivalent performance. The TPRD-1444C/CM produces 70 dB isolation at 600 KHz, with a 350 watt power rating, and insertion loss is 1.5 dB or less. Each duplexer fits a standard 19" rack, with rack height of 5.25" and 4" respectively. The TPRD-1444CM is supplied with adjustable mounting tabs for installation in a cabinet. TPRD-1444C TYPICAL RESPONSE 0 20 Attenuation in dB 40 60 TPRD-1444CM 80 ELECTRICAL SPECIFICATIONS Tuning range 135-151 MHz Frequency separation (min) 600 KHz Maximum input power 350 watts Insertion loss - TX / RX to ant. 1.5 dB TX noise suppression at RX (typ) 70 dB at 600 KHz RX isolation at TX (typ) 70 dB at 600 KHz VSWR (max) 1.5:1 Temperature range -30°C to +70°C Number of cavities (4) - 4" MECHANICAL SPECIFICATIONS 1444C 1444CM Mounting 19" Rack 19" Cabinet Dimensions (HWD) in. (cm) (Tuners fully extended) 5.25 x 19 x 16 13 x 48 x 41 4 x 19 x 16 10 x 48 x 41 Connectors N or UHF female (opt.) Finish Gray acrylic enamel Net weight lb. (kg) 19.25 (8.7) 152 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 600 KHz All specifications subject to change without notice TWDS-6005 Rev. 10/12 DUPLEXERS TPRD-1446C COMPACT PASS / REJECT DUPLEXER The TPRD -1446C of fers high performance in a compact design for the 135-151 MHz VHF band. These duplexers are only one-third of the size of earlier models, and deliver equivalent performance. Custom-extruded 4" cavities allow horizontal rack mounting. Three pass-reject sections for the transmit and receive paths provide 80 dB isolation at 500 KHz, with a 350 watt power rating, and insertion loss of 2.5 dB or less. The duplexer fits a standard 19" rack, with rack height of 8.75". 135 - 151 MHz 6 TYPICAL RESPONSE 0 20 Attenuation in dB 40 60 ELECTRICAL SPECIFICATIONS 80 Tuning range 135-151 MHz Frequency separation (min) 500 KHz Maximum input power 350 watts Insertion loss TX / RX to ant. 2.5 dB TX noise suppression at RX (typ) 80 dB at 500 KHz RX isolation at TX (typ) 80 dB at 500 KHz VSWR (max) 1.5:1 Temperature range -30°C to +70°C Number of cavities (6) - 4" MECHANICAL SPECIFICATIONS Mounting 19" Rack Dimensions (HWD) in. (cm) (Tuners fully extended) 8.75 x 19 x 16 22 x 48 x 40.6 Connectors N or UHF Female Finish Gray acrylic enamel Net weight lb. (kg) 37 (16.8) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 500 KHz All specifications subject to change without notice TWDS-6006 Rev. 10/12 153 TPRD-1454, 1456 BANDPASS / REJECT DUPLEXERS 118 - 148 MHz TPRD-1454 TPRD-1456 Telewave TPRD-1454 and TPRD- rejection of transmitter noise for easy field tuning by rotating the 1456 duplexers allow simultaneous and spurious radiation, providing threaded Invar rod. operation of a transmitter and receiver into a common antenna. These pass-reject duplexers are ideal for systems with very close frequency spacing. excellent receiver protection. Telewave duplexers have ¼" aluminum top plates which are fully welded to the aluminum outer conductor. Silver-plated tuners, The optional TBC-40 indoor cabinet completely encloses the duplexer, and protects it from dust, dirt and tampering. All connections are accessible from the top of the The Telewave TPRD-1454 has two beryllium copper finger stock cabinet. pass-reject cavities in the transmitter contactors and threaded Invar and receiver sections. This duplexer rods assure maximum temperature is designed for transmitters and stability, higher "Q", and many years receivers with frequency spacing of trouble free operation. of 600 KHz or more. Selectivity and insertion loss may be The TPRD-1456 has three pass- adjusted by rotating the calibrated reject cavities in the transmitter connector loops. (See next page for and receiver sections. This duplexer typical response curves.) is designed for transmitters and receivers with frequency spacing of 400 KHz or more. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. If B e c a u s e o f t h e i r s u p e r i o r frequency changes are required, the construction, these Telewave 5" positive locking mechanism allows cavity duplexers achieve greater 154 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6042 Rev. 8/12 TPRD-1454, 1456 118 - 148 MHz 6 DUPLEXERS Attenuation in dB TYPICAL DUPLEX RESPONSE TPRD-1454 0 TPRD-1456 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 90 90 100 600 KHz 100 400 KHz ELECTRICAL SPECIFICATIONS Tuning range Frequency separation (min) Maximum input power VSWR (max) Insertion loss: TX/RX to ant. RX isolation at TX frequency TX noise suppression at RX frequency Temperature range Cavities MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) (Including typical tuner extension) Cavity dimensions Mounting Connectors Finish Net weight lb. (kg) TPRD-1454 600 KHz 1.5 dB 77 dB at 600 KHz 77 dB at 600 KHz (4) 5" TPRD-1456 118-148 MHz 400 KHz 350 watts 1.5:1 2.0 dB 100 dB at 400 KHz 100 dB at 400 KHz -30°C to +70°C (6) 5" 34 x 19 x 11 (86 x 48 x 28) 34 x 19 x 11 (86 x 48 x 28) 23 (10.4) 5" dia x 30" L 19" Rack or wall mount N or UHF female (opt.) Acrylic enamel 35 (15.6) NOTES: Specify model number and exact transmitter and receiver frequencies when ordering. All models are built on 19" rails for rack or wall mounting. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6042 Rev. 8/12 155 118 - 148 MHz TPRD-1484, 1486 PASS-REJECT BASE STATION DUPLEXERS The Telewave TPRD-1484 and TPRD- Telewave duplexers have ¼-inch 1486 duplexers allow simultaneous aluminum top plates which are operation of a transmitter and fully welded to the aluminum receiver into a common antenna. outer conductor. As a result of their These Pass-Reject duplexers are superior construction, Telewave 8" ideal for use in systems requiring cavity duplexers achieve greater maximum isolation, with close rejection of transmitter noise frequency spacing down to 300 and spurious radiation, providing KHz. excellent receiver protection. The TPRD-1484 duplexer has Silver-plated tuners, beryllium two, and TPRD-1486 duplexer copper finger stock contactors, has three pass-reject cavities and threaded Invar rods assure each in the transmit ter and maximum temperature stability, receiver sections. Selectivity and higher "Q", and many years of insertion loss may be adjusted trouble-free operation. by rotating the calibrated connector loops. (See graphs for typical response curves). TPRD-1486 ELECTRICAL SPECIFICATIONS TPRD-1484 TPRD-1486 Tuning range 118-148 MHz Frequency separation (min) 500 KHz 300 KHz Maximum input power 300 watts Insertion loss TX / RX to ant. 1.5 dB 2.2 dB VSWR (max) 1.5:1 Temperature range -30°C to +70°C RX isolation 80 dB at ±500 KHz 100 dB at ±400 KHz TX noise suppression 80 dB at ±500 KHz 100 dB at ±400 KHz MECHANICAL SPECIFICATIONS Cavities (4) - 8" (6) - 8" Mounting 19" Rack or wall mount Connectors N or UHF female (opt.) Finish Gray acrylic enamel Net weight lb. (kg) 37 (16.8) 51 (23.1) Dimensions (HWD) in. (cm) 30 x 19 x 17 (76 x 48 x 43) 30 x 19 x 25 (76 x 48 x 63.5) Tuners fully extended in. (cm) 35 x 19 x 17 (89 x 48 x 43) 35 x 19 x 25 (59 x 48 x 63.5) Attenuation in dB TPRD-1484 TYPICAL RESPONSE CURVES (TPRD-1484) 0 10 20 30 40 50 60 70 80 -.75 -.50 -.25 0 +.25 +.50 Frequency (MHz) 156 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6040 Rev. 7/12 TPRD-1544F PASS-REJECT DUPLEXER 148 - 174 MHz 6 DUPLEXERS TPRD-1544F with TWX-5 spacers The Telewave TPRD-1544F allows simultaneous operation of a transmitter and receiver into a common antenna. This pass-reject duplexer utilizes folded four-inch cavities to achieve high "Q" in a compact size. Telewave folded cavities utilize a special construction technique and circuit design which allow a physically shorter cavity to produce nearly the same performance as a standard length cavity. The TPRD-1544F duplexer uses two folded pass-reject cavities in the transmitter and receiver sections, for frequency spacing of 2 MHz or more. Selectivity and insertion loss may be adjusted by rotating the calibrated connector loops. This duplexer is designed to mount horizontally on a 19" rack. Spacing brackets are available to allow mounting in a cabinet with 5" or 8" depth from the front. Telewave duplexers feature cavities with ¼" aluminum top plates, which are fully welded to the aluminum outer conductor. Silver-plated tuners, beryllium copper finger stock contactors and threaded Invar rods assure maximum temperature stability, and many years of trouble free operation. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. If frequency changes are required, the positive locking mechanism allows for straightforward field tuning by rotating the threaded Invar rod. ELECTRICAL SPECIFICATIONS Tuning range Frequency separation (min) Maximum input power Insertion loss TX / RX to ant. (typ.) TX noise suppression at RX (min) RX isolation at TX (min) VSWR (max) Temperature range Number of cavities MECHANICAL SPECIFICATIONS Mounting Dimensions (HWD) in. (cm) (Tuners fully extended) Connectors Finish Net weight lb. (kg) 148-174 MHz 2 MHz 350 watts 1.0 dB 80 dB at 2 MHz 80 dB at 2 MHz 1.5:1 -30°C to +60°C (4) - 4" 19" Rack mount 5.25 x 19 x 17 (13.3 x 48.3 x 43.2) N or UHF Female Gray acrylic enamel 15 (6.8) TYPICAL RESPONSE Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6041 Rev. 4/10 157 148 - 174 MHz TPRD-1543C COMPACT PASS / REJECT DUPLEXER The TPRD-1543C produces high performance in a compact design for the 148-174 MHz VHF band. This duplexer is less than 30% of the size of earlier models, and delivers equivalent performance. Precise construction and high quality components results in excellent temperature stability under the most demanding conditions. The duplexer fits a standard 19" rack, with rack height of 5.25". Each duplexer is tuned and tested for maximum performance prior to shipping. TYPICAL RESPONSE 0 20 Attenuation in dB 40 60 80 ELECTRICAL SPECIFICATIONS Tuning range Frequency separation (min) Maximum input power Insertion loss TX / RX to ant. TX noise suppression at RX (typ) RX isolation at TX (typ) VSWR (max) Temperature range Number of cavities MECHANICAL SPECIFICATIONS Mounting Dimensions (HWD) in. (tuning rods fully extended) in. Connectors Finish Net weight lb. (kg) 148-174 MHz 5 MHz 350 watts 1.5 dB 90 dB 50 dB 1.5:1 -30°C to +70°C (3) - 4" 19" Rack 5.25 x 19 x 11.5 5.25 x 19 x 16.5 N or UHF female Acrylic enamel 15 lb. 159.5 164.5 Frequency (MHz) 169.5 158 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6029 Rev. 10/12 DUPLEXERS TPRD-1544C, 1544CM COMPACT PASS / REJECT DUPLEXER The TPRD-1544C and 1544CM produce high performance in a compact design for the 148-174 MHz VHF band. These duplexers are less than 30% of the size of earlier models, and deliver greater isolation and power handling. The TPRD-1544C and CM produce 70 dB isolation at 600 KHz, with 350 watt power handling, and insertion loss is 1.5 dB or less. Each duplexer fits a standard 19-inch rack, with rack height of 5.25" and 4" respectively. The TPRD-1544CM is supplied with adjustable mounting tabs for installation in a cabinet. 148 - 174 MHz 6 TPRD-1544C TYPICAL RESPONSE 0 20 Attenuation in dB 40 60 TPRD-1544CM 80 ELECTRICAL SPECIFICATIONS Tuning range 148-174 MHz Frequency separation (min) 600 KHz Maximum input power 350 watts Insertion loss TX / RX to ant. 1.5 dB TX noise suppression at RX (typ) 70 dB at 600 KHz RX isolation at TX (typ) 70 dB at 600 KHz VSWR (max) 1.5:1 Temperature range -30°C to +70°C Number of cavities (4) - 4" MECHANICAL SPECIFICATIONS 1544C 1544CM Mounting 19" Rack 19" Cabinet Dimensions (HWD) in. (cm) (tuning rods fully extended) 5.25 x 19 x 15 4 x 19 x 15 (38.7 x 48 x 38.1) (10.2 x 48 x 38.1) Connectors N or UHF female (opt.) Finish Acrylic enamel Net weight lb. (kg) 18.25 (8.3) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 600 KHz All specifications subject to change without notice TWDS-6001 Rev. 10/12 159 TPRD-1546C COMPACT PASS / REJECT DUPLEXER The TPRD -1546C of fers high performance in a compact design for the 148-174 MHz VHF band. Custom extruded 4" cavities allow horizontal rack mounting. Three pass-reject sections in the transmit and receive paths provide 80 dB isolation at 500 KHz, with a 350 watt power rating, and insertion loss of 2.5 dB or less. The duplexer fits a standard 19" rack, with rack height of 8.75". 148 - 174 MHz TYPICAL RESPONSE 0 20 Attenuation in dB 40 60 ELECTRICAL SPECIFICATIONS 80 Tuning range 148-174 MHz Frequency separation (min) 500 KHz Maximum input power 350 watts Insertion loss TX / RX to ant. 2.5 dB TX noise suppression at RX (typ) 80 dB at 500 KHz RX isolation at TX (typ) 80 dB at 500 KHz VSWR (max) 1.5:1 Temperature range -30°C to +70°C Number of cavities (6) - 4" MECHANICAL SPECIFICATIONS Mounting 19" Rack mount Dimensions (HWD) in. (cm) 8.75 x 19 x 15 (22 x 48 x 38) Connectors N or UHF female Finish Acrylic enamel Net weight lb. (kg) 36 (16.3) 160 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 500 KHz All specifications subject to change without notice TWDS-6004 Rev. 10/12 TPCD-1553, 1554, 1556 VHF BANDPASS DUPLEXERS 148 - 174 MHz 6 DUPLEXERS TPCD-1553 TPCD-1554 TPCD-1556 T h e Te l e w a v e T P C D -15 5 3 , contactors and threaded Invar The TPCD-1556 has three bandpass TPCD -1554, and TPCD -1556 rods assure maximum temperature cavities in both the transmitter and allow simultaneous operation of stability, higher "Q", and many years receiver sections. This duplexer a transmitter and receiver into a of trouble free operation. is designed for transmitters and common antenna. These bandpass duplexers are ideal in frequency congested areas where protection is needed from surrounding transmitters, and where maximum transmitter sideband filtering is necessary. Because of their superior construction, these Telewave 5" cavity duplexers achieve greater rejection of transmitter noise Selectivity and insertion loss may be adjusted by rotating the calibrated connector loops. (See next page for typical response curves.) The TPCD-1553 includes t wo bandpass cavities in the transmitter section. It is recommended when frequency spacing between transmitter and receiver is 5 MHz or more. receivers with spacing of 2 MHz or more. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. If frequency changes are required, the positive locking mechanism allows for easy field tuning by rotating the threaded Invar rod. and spurious radiation, providing The TPCD-1554 has two bandpass excellent receiver protection. cavities in both the transmitter and Telewave duplexers have ¼" receiver sections. This duplexer aluminum top plates which are is designed for transmitters and fully welded to the aluminum outer receivers with a spacing of 4 MHz conductor. Silver-plated tuners, or more. beryllium copper finger stock Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6024 Rev. 8/12 161 TPCD-1553, 1554, 1556 148 - 174 MHz Attenuation in dB TPCD-1553 0 10 20 30 40 50 60 70 TYPICAL DUPLEX RESPONSE TPCD-1554 0 TPCD-1556 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 -2 Fo +2 +4 +6 -2 Fo +2 +4 +6 Frequency (MHz) -4 -2 Fo +2 +4 +6 ELECTRICAL SPECIFICATIONS Tuning range Cavities Frequency separation (min) Maximum input power VSWR (max) Insertion loss TX / RX to ant. RX isolation at TX TX noise suppression at RX Temperature range MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (Tuners fully extended) (cm) Connectors Finish Net weight lb. (kg) TPCD-1553 (3) - 5" 5 MHz 1.0 dB 35 dB at 5 MHz 62 dB at 5 MHz 28 x 19 x 6 (71 x 48 x 15) 15 (7) TPCD-1554 148-174 MHz (4) - 5" 4 MHz 350 watts 1.5:1 1.0 dB 55 dB at 4 MHz 58 dB at 5 MHz 58 dB at 4 MHz 63 dB at 5 MHz -30°C to +70°C 28 x 19 x 11 (71 x 48 x 28) N or UHF Female Gray acrylic enamel 19 (8.6) TPCD-1556 (6) - 5" 2 MHz 1.5 dB 63 dB at 2 MHz 75 dB at 3 MHz 66 dB at 2 MHz 77 dB at 3 MHz 28 x 19 x 11 (71 x 48 x 28) 27 (12.3) NOTES: Specify model number and exact transmitter and receiver frequencies when ordering. All models are built on 19" rails for rack or wall mounting. 162 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6024 Rev. 8/12 TPRD-1554, 1556 BANDPASS / REJECT DUPLEXERS 144 - 174 MHz 6 DUPLEXERS TPRD-1554 TPRD-1556 Telewave TPRD-1554 and TPRD- rejection of transmitter noise for easy field tuning by rotating the 1556 duplexers allow simultaneous and spurious radiation, providing threaded Invar rod. operation of a transmitter and receiver into a common antenna. These pass-reject duplexers are ideal for systems with very close frequency spacing. excellent receiver protection. Telewave duplexers have ¼" aluminum top plates which are fully welded to the aluminum outer conductor. Silver-plated tuners, The optional TBC-40 indoor cabinet completely encloses the duplexer, and protec ts it from dust, dirt and tampering. All connections are accessible The Telewave TPRD-1554 has two beryllium copper finger stock from the top of the cabinet. pass-reject cavities in the transmitter contactors and threaded Invar and receiver sections. This duplexer rods assure maximum temperature is designed for transmitters and stability, higher "Q", and many years receivers with frequency spacing of trouble free operation. of 600 KHz or more. Selectivity and insertion loss may be The TPRD-1556 has three pass- adjusted by rotating the calibrated reject cavities in the transmitter connector loops. (See next page for and receiver sections. This duplexer typical response curves.) is designed for transmitters and receivers with frequency spacing of 400 KHz or more. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. If B e c a u s e o f t h e i r s u p e r i o r frequency changes are required, the construction, these Telewave 5" positive locking mechanism allows cavity duplexers achieve greater Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6025 Rev. 8/12 163 TPRD-1554, 1556 144 - 174 MHz Attenuation in dB TYPICAL DUPLEX RESPONSE TPRD-1554 0 TPRD-1556 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 90 90 100 600 KHz 100 400 KHz ELECTRICAL SPECIFICATIONS Tuning range Frequency separation (min) Maximum input power VSWR (max) Insertion loss: TX/RX to ant. RX isolation at TX frequency TX noise suppression at RX frequency Temperature range Cavities MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) (Including typical tuner extension) Cavity dimensions Mounting Connectors Finish Net weight lb. (kg) TPRD-1554 600 KHz 1.5 dB 77 dB at 600 KHz 77 dB at 600 KHz (4) 5" TPRD-1556 144-174 MHz 400 KHz 350 watts 1.5:1 2.0 dB 100 dB at 400 KHz 100 dB at 400 KHz -30°C to +70°C (6) 5" 28 x 19 x 11 (71.1 x 48 x 28) 28 x 19 x 11 (71.1 x 48 x 28) 19 (8.6) 5" dia x 23" L 19" Rack or wall mount N or UHF female (opt.) Acrylic enamel 27 (12.3) NOTES: Specify model number and exact transmitter and receiver frequencies when ordering. All models are built on 19" rails for rack or wall mounting. 164 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6025 Rev. 8/12 TPRD-1566 BANDPASS - BANDREJECT DUAL NOTCH DUPLEXER 148 - 174 MHz 6 DUPLEXERS The Telewave TPRD-1566 allows rejection of transmitter noise The optional TBC-40 indoor cabinet simultaneous operation of a and spurious radiation, providing completely encloses the duplexer, transmitter and receiver into a excellent receiver protection. and protects it from dust, dirt common antenna. This pass/reject duplexer has low insertion loss, and is ideal for systems with close frequency separation. Telewave duplexers have ¼" aluminum top plates which are fully welded to the aluminum outer conductor. Silver-plated tuners, and tampering. All connections are accessible from the top of the cabinet. The TPRD-1566 has three pass/ beryllium copper finger stock reject cavities in both the transmitter contactors and threaded Invar and receiver sections. This duplexer rods assure maximum temperature is designed for transmitters and stability, higher "Q", and many years receivers with frequency spacing of trouble free operation. of 300 KHz or more. Selectivity and insertion loss may be adjusted by rotating the calibrated connector loops. (See next page for typical response curves.) All duplexers are tuned and tested with customer-specified frequencies prior to shipping. If frequency changes are required, the positive locking mechanism allows B e c a u s e o f t h e i r s u p e r i o r for easy field tuning by rotating the construction, these Telewave 6" threaded Invar rod. cavity duplexers achieve greater Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6037 Rev. 8/12 165 TPRD-1566 148 - 174 MHz Attenuation in dB TYPICAL DUPLEX RESPONSE TPRD-1566 1.0 dB Insertion Loss TPRD-1566 2.0 dB Insertion Loss 0 0 20 20 40 40 60 60 80 80 100 100 120 120 -.500 -.250 0 +.250 +.500 Frequency (MHz) -.500 -.250 0 +.250 +.500 ELECTRICAL SPECIFICATIONS Tuning range 148-174 MHz Number of cavities (6) - 6" Frequency separation (min) 300 KHz Maximum input power 350 watts VSWR (max) 1.5:1 RX isolation at TX frequency 100 dB at 500 KHz Insertion loss - 1.0 dB TX noise suppression at RX 100 dB at 500 KHz Insertion loss - 1.0 dB RX isolation at TX frequency 115 dB at 500 KHz Insertion loss - 2.0 dB TX noise suppression at RX Temperature range 115 dB at 500 KHz Insertion loss - 2.0 dB -30°C to +70°C MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Tuners fully extended in. (cm) 23 x 19 x 14 (58.4 x 48.3 x 35.6) 28 x 19 x 14 (71 x 48.3 x 35.6) Connectors N or UHF Female (opt.) Finish Gray acrylic enamel Net weight lb. (kg) 55 (25) NOTES: Specify model number and exact transmitter and receiver frequencies when ordering. All models are built on 19" rails for rack or wall mounting. 166 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6037 Rev. 8/12 DUPLEXERS TPRD-1584, 1586 PASS-REJECT BASE STATION DUPLEXER 148 - 174 MHz 6 Telewave models TPRD-1584 and A s a result of their superior TPRD-1586 allow simultaneous construction, Telewave 8" cavity operation of a transmitter and duplexers achieve greater rejection receiver into a common antenna. of transmitter noise and spurious These Pass-Reject duplexers are an radiation, providing excellent ideal choice for systems requiring receiver protection. maximum isolation, with close frequency spacing down to 300 KHz. Silver-plated tuners, beryllium copper finger stock contactors, and threaded Invar rods assure The TPRD-1584 has two, and the maximum temperature stability, TPRD-1586 has three Pass-Reject higher "Q", and many years of cavities each in the transmitter and trouble-free operation. receiver sections. Selectivity and insertion loss may be adjusted by rotating the calibrated connector loops. (See graph for typical response curves.) Telewave duplexers have ¼-inch aluminum top plates which are fully welded to the aluminum outer conductor. TPRD-1586 ELECTRICAL SPECIFICATIONS TPRD-1584 TPRD-1586 Tuning range 148-174 MHz Frequency separation (min) 500 KHz 300 KHz Maximum input power 350 watts Insertion loss TX / RX to ant. 1.5 dB 2.2 dB VSWR (max) 1.5:1 Temperature range -30°C to +70°C RX isolation 80 dB at ±500 KHz 100 dB at ±400 KHz TX noise suppression 80 dB at ±500 KHz 100 dB at ±400 KHz MECHANICAL SPECIFICATIONS Cavities (4) - 8" (6) - 8" Mounting 19" Rack mount Connectors N or UHF female (opt.) Finish Gray acrylic enamel Net weight lb. (kg) 33 (15) 46.5 (21) Dimensions (HWD) in. (cm) 23.5 x 19 x 17 (60 x 48 x 43) 23.5 x 19 x 25 (60 x 48 x 63.5) Tuners fully extended in. (cm) 28 x 19 x 17 (71 x 48 x 43) 28 x 19 x 25 (71 x 48 x 63.5) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com Attenuation in dB TPRD-1584 TYPICAL RESPONSE (TPRD-1584) 0 10 20 30 40 50 60 70 80 -.75 -.50 -.25 0 +.25 +.50 Frequency (MHz) All specifications subject to change without notice TWDS-6039 Rev. 7/12 167 200 - 300 MHz TPRD-2254 BANDPASS / REJECT DUPLEXER The Telewave TPRD-2254 allows rods assure maximum temperature simultaneous operation of a stability, higher "Q", and many years transmitter and receiver into a of trouble free operation. common antenna. This pass-reject duplexer has low insertion loss, and is ideal for systems with close frequency separation. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. If frequency changes are required, the The TPRD-2254 has two pass- positive locking mechanism allows reject cavities in the transmitter for easy field tuning by rotating the and receiver sections. This duplexer threaded Invar rod. is designed for transmitters and receivers with frequency spacing of 1 MHz or more. Selectivity and insertion loss may be adjusted by rotating the calibrated connector loops. The optional TBC-40 indoor cabinet completely encloses the duplexer, and protects it from dust, dirt and tampering. All connections are accessible from the top of the cabinet. Telewave duplexers have ¼" aluminum top plates which are fully welded to the aluminum outer conductor. Silver-plated tuners, beryllium copper finger stock contactors and threaded Invar TPRD-2254 ELECTRICAL SPECIFICATIONS Tuning range Frequency separation (min) Maximum input power Insertion loss TX / RX to ant. TX noise suppression at RX (min) RX isolation at TX (min) VSWR (max) Temperature range Number of cavities MECHANICAL SPECIFICATIONS Mounting Dimensions (HWD) in. (cm) (Tuners fully extended) Cavity dimensions Connectors Finish Net weight lb. (kg) 200-300 MHz 1 MHz 350 watts 1.0 dB 84 dB at 1.5 MHz 85 dB at 1.5 MHz 1.5:1 -30°C to +70°C (4) - 5" 19" Rack mount 23 x 19 x 11 (58 x 48 x 28) 5" dia x 18" L N or UHF Female Gray acrylic enamel 17 (7.7) Attenuation in dB TYPICAL DUPLEX RESPONSE 0 1.0 dB I.L. 10 at 223.1 MHz 1.0 dB I.L. at 224.7 MHz 20 30 40 50 Tx-Rx 60 70 80 Fo +1.0 +2.0 Frequency (MHz) NOTES: Specify exact transmitter and receiver frequencies when ordering. All models are built on 19" rails for rack or wall mounting. 168 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6026 Rev. 9/12 TPCD-4554, 4556 UHF BANDPASS DUPLEXERS 400 - 512 MHz 6 DUPLEXERS TPCD-4554 TPCD-4556 The Telewave TPCD-4554 and These duplexers are designed for If frequency changes are required, TPCD - 4556 duplexers allow transmitters and receivers with the positive locking mechanism simultaneous operation of a frequency spacing of 5 MHz or allows for easy field tuning by transmitter and receiver into a more. rotating the threaded Invar rod. common antenna. These bandpass duplexers have low insertion loss, and are ideal in frequency congested areas where protection is needed from surrounding transmitters, Selectivity and insertion loss may be adjusted by rotating the calibrated connector loops. (See next page for typical response curves.) and where maximum transmitter Telewave duplexers have ¼-inch sideband filtering is necessary. aluminum top plates which are Because of their superior construction, these Telewave 5" cavity duplexers achieve greater rejection of transmitter noise and spurious radiation, providing excellent receiver protection. fully welded to the aluminum outer conductor. Silver-plated tuners, beryllium copper finger stock contactors and threaded Invar rods assure maximum temperature stability, higher "Q", and many years of trouble free operation. The TPCD-4554 has two, and the TPCD-4556 has three, ¾wave bandpass cavities in the transmitter and receiver sections. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6019 Rev. 8/12 169 TPCD-4554, 4556 400 - 512 MHz Attenuation in dB TYPICAL DUPLEX RESPONSE TPCD-4554 0 TPCD-4556 0 10 10 20 20 30 30 40 40 50 50 60 60 70 70 80 80 -1 0 +1 +2 +3 +4 +5 +6 -4 -2 0 +2 +4 +6 +8 Frequency (MHz) ELECTRICAL SPECIFICATIONS Tuning range Number of cavities Frequency separation (min) Maximum input power VSWR (max) Insertion loss TX / RX to ant. RX isolation at TX frequency TX noise suppression at RX frequency Temperature range MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) (Tuners fully extended) Connectors Finish Net weight lb. (kg) TPCD-4554 (4) - 5" 1.0 dB 50 dB at 5 MHz 52 dB at 5 MHz TPCD-4556 400-512 MHz (6) - 5" 5 MHz 350 watts 1.5:1 1.5 dB 75 dB at 5 MHz 75 dB at 5 MHz -30°C to +70°C 28 x 19 x 11 (74 x 48 x 28) 19 (8.6) N or UHF female Gray acrylic enamel 27 (12.3) NOTES: Specify exact transmitter and receiver frequencies when ordering. All models are built on 19" rails for rack or wall mounting. 170 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6019 Rev. 8/12 DUPLEXERS TPRD-4544, 4744 PASS / REJECT DUPLEXER The Telewave TPRD-4544/4744 Base Station duplexers provide high performance with an innovative design. By using two TPRC-4504 or 4704 Pass / Reject cavities in the transmitter and receiver path, these duplexers provide maximum TX to RX protection in the most severe RF environments. The design of these duplexers provides a bandpass characteristic with minimum insertion loss, while also providing maximum TX to RX protection. Adjustable coupling optimizes the required attenuation for ideal RX performance. All cavity inputs are electrically shorted to ground for maximum static and noise protection. RG-214 Mil-Spec cable is used TPRD-4544/4744 duplexers mount for all interconnections to ensure on a 19" standard rack, with panel long life, and lowest insertion loss height of 5.25". Power handling with maximum power handling is 250 watts. Receiver desense capability. Heavy-duty materials protection is at least 90 dB, and are used in construction of these TX sideband suppression is at least duplexers, including silver-plated 75 dB. tuners and beryllium copper fingerstock contactors, assuring high "Q" performance with no problems due to dissimilar metals. Tuning is simple and remains stable from -30°C to +70°C, thanks to the threaded Invar rod. With TX to RX spacing of 3 MHz or more, this duplexer can also combine two transmitters into one antenna, or feed two receivers. For spacing less than 3 MHz, please contact Telewave for assistance. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. No further adjustments should be required. The positive locking mechanism allows for simple field tuning if frequency changes are required. 400 - 512 MHz 6 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6014 Rev. 9/07 171 TPRD-4544, 4744 400 - 512 MHz Attenuation in dB TPRD-4544 RESPONSE AT 5 MHz SEPARATION TPRD-4744 RESPONSE AT 3 MHz SEPARATION 0 10 20 30 40 50 60 70 80 -1 0 10 20 30 40 50 Low Pass to 60 High Pass 70 80 0 +1 +2 +3 +4 +5 +6 -1 -2 Frequency (MHz) Low Pass to High Pass 0 +1 +2 +3 +4 +5 SPECIFICATIONS TPRD-4544 Frequency range 400-470 MHz TX / RX separation (min) 5 MHz ELECTRICAL SPECIFICATIONS Maximum input power Insertion loss (TX & RX to Antenna) TX noise suppression at RX frequency RX attenuation at TX frequency Isolation TX to RX (min) 5 MHz separation 3 MHz separation VSWR (max) Temperature range MECHANICAL SPECIFICATIONS Number of cavities Dimensions (HWD) in. (cm) Mounting Connector termination Finish Net weight lb. (kg) Shipping weight lb. (kg) TPRD-4744 470-512 MHz 3 MHz 250 watts 1.0 dB 90 dB 90 dB 75 dB 60 dB 1.5:1 -30°C to +70°C (4) - 4" Dia. x 8" L 5.25 x 19 x 12 (13.3 x 48 x 30.5) 19" Panel N Female Gray acrylic enamel 10 (4.5) 15 (6.8) NOTE: Exact transmitter and receiver frequencies must be specified when ordering. 172 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6014 Rev. 9/07 TPRD-4546 UHF BANDPASS / BANDREJECT DUPLEXER 400 - 512 MHz 6 DUPLEXERS The Telewave TPRD-4546 UHF H e a v y - d u t y m a t e r i a l s a r e duplexer allows simultaneous used throughout to insure top operation of a transmitter or performance and long service. combiner and receiver into a Each cavity is constructed with a common antenna. This band-pass/ ¼" aluminum top plate which is fully band-reject duplexer provides welded to the cavity body. maximum TX-to-RX isolation with minimum insertion loss. Six 4" high "Q" cavities in a pass/reject configuration provide better isolation with close frequency spacing than an equivalent bandpass-only duplexer. RG-214 Mil-Spec cable is used for the interconnect, and temperature stability is maintained by the use of a threaded Invar tuning rod. Tuners are all silver-plated, and sliding contacts are manufactured from beryllium copper fingerstock. The TPRD-4546 can also be configured for at least 1.2 MHz pass and reject bandwidth with rated attenuation. The TPRD-4546 is rack mounted on a 7" x 19" panel. Selectivity and insertion loss are adjustable as required. All duplexers are tuned The superior construc tion of and tested with customer specified Telewave duplexers allows the frequencies prior to shipping, and highest possible rejec tion of no further adjustment should be transmitter spurious radiation required before installation. and noise, providing maximum protection for the receiver system. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6020 Rev. 10/08 173 TPRD-4546 400 - 512 MHz Attenuation in dB 0 10 20 30 40 50 60 70 80 -10.0 TYPICAL RESPONSE Fo Frequency (MHz) +10.0 ELECTRICAL SPECIFICATIONS Frequency range Frequency separation (min) Pass / reject bandwidth (typ) Maximum input power Insertion loss at pass band (TX and RX) TX attenuation at RX band (typ) RX attenuation at TX Band (typ) TX to RX Attenuation at 3 MHz (min) TX to RX Attenuation at 5 MHz (min) Impedance / VSWR (max) Temperature range MECHANICAL SPECIFICATIONS Number of cavities Dimensions (HWD) in. (cm) Mounting Connectors Panel finish Cavity finish Net weight lb. (kg) Shipping weight lb. (kg) 400-512 MHz 3 MHz 1.2 MHz 250 watts 1.75 dB typ. / 2.0 dB max 95 dB 95 dB 85 dB 90 dB 50 ohms / 1.5:1 -30°C to +70°C (6) - 4" Dia. x 8" L 7 x 19 x 11 (17.8 x 48.3 x 28) 19" Panel N Female Clear alodine Gray enamel 16 (7.3) 19.5 (8.9) NOTE: Exact transmitter and receiver frequencies must be specified when ordering. 174 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6020 Rev. 10/08 TPRD-4554, 4556 PASS / REJECT DUPLEXERS 400 - 512 MHz 6 DUPLEXERS TPRD-4554 TPRD-4556 Telewave TPRD-4554 and TPRD- Telewave duplexers have ¼" The optional TBC-40 indoor cabinet 4556 duplexers allow simultaneous aluminum top plates which are completely encloses the duplexer, operation of a transmitter and fully welded to the aluminum outer and protects it from dust, dirt receiver into a common antenna. conductor. Silver-plated tuners, and tampering. All connections These pass-reject duplexers are beryllium copper finger stock are accessible from the top of the ideal for systems with very close contactors and threaded Invar cabinet. frequency spacing of 1 MHz or rods assure maximum temperature more. stability, higher "Q", and many years The Telewave TPRD-4554 has two of trouble free operation. ¾-wave pass-reject cavities in the Selectivity and insertion loss may be transmitter and receiver sections. adjusted by rotating the calibrated The TPRD-4556 has three ¾-wave connector loops. (See next page for pass-reject cavities in the transmitter typical response curves.) and receiver sections for additional isolation. All duplexers are tuned and tested with customer-specified B e c a u s e o f t h e i r s u p e r i o r frequencies prior to shipping. If construction, these Telewave 5" frequency changes are required, the cavity duplexers achieve greater positive locking mechanism allows rejec tion of transmit ter noise for easy field tuning by rotating the and spurious radiation, providing threaded Invar rod. excellent receiver protection. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6035 Rev. 8/12 175 TPRD-4554, 4556 400 - 512 MHz Attenuation in dB TYPICAL DUPLEX RESPONSE TPRD-4554 0 10 20 30 40 50 60 70 80 90 100 1 MHz TPRD-4556 0 10 20 30 40 50 60 70 80 90 100 1 MHz ELECTRICAL SPECIFICATIONS Tuning range Frequency separation (min) Maximum input power VSWR (max) Insertion loss TX/RX to ant. RX isolation at TX frequency TX noise suppression at RX frequency Temperature range Cavities MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) (Tuners fully extended) Mounting Connectors Finish Net weight lb. (kg) TPRD-4554 1.5 dB 80 dB at 1 MHz 80 dB at 1 MHz (4) 5" 400-512 MHz 1 MHz 350 watts 1.5:1 -30°C to +70°C TPRD-4556 2.3 dB 95 dB at 1 MHz 95 dB at 1 MHz (6) 5" 28 x 19 x 11 (71.1 x 48 x 28) 28 x 19 x 11 (71.1 x 48 x 28) 19" Rack or wall mount N or UHF female (opt.) Acrylic enamel 19 (8.6) 27 (12.3) Specify model number and exact transmitter and receiver frequencies when ordering. 176 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6035 Rev. 8/12 TTPD-7644 BANDPASS / BANDREJECT DUPLEXER 763 - 869 MHz 6 DUPLEXERS The Telewave TTPD-7644 Base finger stock contactors assure long Station Duplexer is designed life, high "Q" performance, and specifically for the 763-869 MHz mechanical stability. Public Safety frequency band. Four Bandpass / Band-Reject cavities utilize an exclusive Telewave coupling technique to provide a true bandpass response, while rejecting Solid copper semi-rigid cable and non-ferromagnetic materials virtually eliminate internal intermod generation. a specified frequency band. A threaded Invar tuning rod and Maximum transmitter-to-receiver protection is achieved across the full transmitter and receiver bands, with very low insertion loss. temperature compensator provide frequency stability across the full temperature range. All cavity inputs are heavily grounded for greatest static and lightning protection. The TTPD-7644 is a compact, rack mounted duplexer on a 5.25" x 19" panel, with a power rating of 650 watts. Heavy duty materials including ¼-inch top and bottom plates add to the rugged design of this duplexer. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. No further adjustments should be required. The positive locking mechanism makes field-tuning simple if frequency changes are All connectors and tuners are necessary. silver-plated, and beryllium copper Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6034 Rev. 10/12 177 TTPD-7644 763 - 869 MHz Attenuation in dB TYPICAL DUPLEX RESPONSE 0 10 20 30 40 50 60 70 80 90 100 763 Fc 869 Frequency (MHz) ELECTRICAL SPECIFICATIONS Frequency range Frequency separation (min) Maximum input power TX or RX pass bandwidth Insertion loss at pass bandwidth TX (high frequency) RX (low frequency) TX attenuation at RX band (min) RX attenuation at TX band (min) TX-to-RX attenuation (min) VSWR, ref. to 50 ohms (max) Temperature range Number of cavities MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Mounting Connectors Finish Net weight lbs (kg) Shipping weight lbs (kg) 763-869 MHz 30 MHz (764-806 MHz) / 45 MHz (806-869 MHz) 650 watts 5 MHz 0.5 dB max / 0.35 dB (typ) 0.7 dB max / 0.5 dB (typ) 90 dB 90 dB 80 dB 1.5:1 -30°C to +70°C 4 5.25 x 19 x 11 (13 x 48 x 28) 19" Panel N Female Acrylic enamel 8.25 (3.7) 13 (5.9) Specify exact transmitter and receiver frequencies when ordering. 178 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6034 Rev. 10/12 DUPLEXERS TTPD-8642, TTPD-8644 BANDPASS / BAND-REJECT DUPLEXERS TTPD-8642 806 - 960 MHz 6 TTPD-8644 The Telewave TTPD-8642 and All connectors and tuners are be required. The positive locking TTPD-8644 Base Station duplexers silver-plated, and beryllium copper mechanism makes field-tuning are designed for the 806-960 MHz finger stock contactors assure long simple if frequency changes are frequency band. Bandpass / Band- life, high "Q" performance, and necessary. Reject cavities utilize an exclusive mechanical stability. Telewave coupling technique to provide a true bandpass response, while rejecting a specified frequency band. Solid copper semi-rigid cable and non-ferromagnetic materials virtually eliminate internal intermod generation Maximum transmitter-to-receiver protection is achieved across the full transmitter and receiver bands, with very low insertion loss. A threaded Invar tuning rod and temperature compensator provide frequency stability across the full temperature range. All cavity inputs The TTPD-8642 and TTPD-8644 are are heavily grounded for greatest compact, rack mounted duplexers static and lightning protection. on a 5.25" x 19" panel, with a power rating of 350 and 650 watts. Heavy duty materials which include ¼-inch top and bottom plates add to the rugged design of these duplexers. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. No further adjustments should Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6018 Rev. 10/12 179 TTPD-8642, TTPD-8644 806 - 960 MHz Attenuation in dB TYPICAL DUPLEX RESPONSE TTPD-8642 0 10 20 30 40 50 60 70 80 TTPD-8644 0 10 5 MHz 20 30 40 50 60 70 80 90 100 5 MHz 800 820 840 860 880 806 Fc 896 Frequency (MHz) ELECTRICAL SPECIFICATIONS Frequency range Frequency separation (min) Maximum input power TX or RX pass bandwidth Insertion loss (TX/RX to ant., typ) TX (high frequency) RX (low frequency) TX noise suppression at RX (min) RX attenuation at TX (min) TX-RX isolation at 45 MHz (min) TX-to-RX attenuation (min) VSWR (max) Impedance Temperature range Number of cavities MECHANICAL SPECIFICATIONS Cavity diameter in. (cm) Dimensions (HWD) in. (cm) Mounting Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) TTPD-8642 350 watts 0.5 dB 70 dB 70 dB 70 dB 2 TTPD-8644 806-960 MHz 45 MHz 650 watts 5 MHz 0.5 dB 0.5 dB max / 0.35 dB typ. 0.7 dB max / 0.5 dB typ. 85 dB 85 dB 85 dB 75 dB 1.5:1 50 ohms -30°C to +70°C 4 4 (1.8) 7 (3.2) 4 (10) 5.25 x 19 x 8.5 (13 x 48 x 22) 19" Panel N Female Acrylic enamel 8.25 (3.7) 13 (5.9) 180 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6018 Rev. 10/12 TPRD-8644 PASS/REJECT DUPLEXER 763 - 869 MHz 6 DUPLEXERS The Telewave TPRD-8644 Base performance with no problems due The TPRD-8644 mounts on a 19" Station Duplexer provides high to dissimilar metals. Heliarc welded standard rack, with panel height of performance and high reliability top and bottom plates ensure 5.25". Power handling is 250 watts. for the 760 or 860 MHz Public reliable, noise-free operation. Receiver desense protection is Safety and trunking bands. This Tuning is simple and remains stable at least 80 dB, and TX sideband duplexer can be easily reconfigured from -30º C to +70º C, thanks to the suppression is at least 80 dB. for transition from one band to the other. With two Pass/Reject cavities in each transmitter and receiver path, these duplexers provide maximum TX to RX protection in dense RF environments. threaded Invar tuning rod. Adjustable coupling optimizes the required attenuation for ideal RX performance. All cavity inputs are electrically shorted to ground for maximum static and noise With TX to RX spacing of 5 MHz or more, this duplexer can combine two transmitters into one antenna, or feed two receivers. For spacing less then 5 MHz, please contact Telewave for additional Mil-Spec semi-rigid cable is used protection. information. for all interconnections to ensure long life, and lowest insertion loss with maximum power handling capability All duplexers are tuned and tested with customer-specified frequencies prior to shipping. No further adjustments should Heavy-duty materials are used be required. The positive locking in construction of this duplexer, mechanism allows for easy field including silver-plated tuners and tuning if frequency changes are ber yllium copper fingerstock implemented. contactors, assuring high "Q" Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6033 Rev. 9/08 181 TPRD-8644 763 - 869 MHz Attenuation in dB TYPICAL RESPONSE 0 15 30 45 60 75 Tx-Rx 90 105 800 810 820 830 840 850 860 870 880 Frequency (MHz) ELECTRICAL SPECIFICATIONS Frequency range 763-869 MHz Frequency separation (min) 30 MHz (764-806 MHz) / 45 MHz (806-869 MHz) Maximum input power 250 watts Insertion loss (TX/RX to ant., typ) 1.0 dB TX noise suppression at RX (min) 80 dB RX attenuation at TX (min) 80 dB TX-RX isolation for 5 MHz separation (min) 70 dB VSWR (max) 1.5:1 Impedance 50 ohms Temperature range -30°C to +70°C Number of cavities 4 MECHANICAL SPECIFICATIONS Cavity diameter in. (cm) 4 (10) Dimensions (HWD) in. (cm) 5.25 x 19 x 10.5 (13 x 48 x 26.67) Mounting 19" Panel Connectors N Female Finish Acrylic enamel Net weight lb. (kg) 21 (9.6) Shipping weight lb. (kg) 26 (11.8) Specify exact transmitter and receiver frequencies when ordering. 182 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6033 Rev. 9/08 TPRD-9044 PASS/REJECT DUPLEXER 890 - 960 MHz 6 DUPLEXERS The Telewave TPRD-9044 Base Adjustable coupling optimizes or feed two receivers. Typical Station Duplexer provides high the required attenuation for ideal spacing is 39 MHz. Alternate performance and high reliability RX performance. All cavity inputs spacing of 3.6 MHz, 9 MHz or other for 900 MHz radio systems. With are electrically shorted to ground is also available. Frequencies and two Pass/Reject cavities in each for maximum static and noise required spacing must be specified transmitter and receiver path, protection. with all orders. these duplexers provide maximum TX to RX protection in dense RF environments. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. Mil-Spec semi-rigid cable is used No further adjustments should for all interconnections to ensure be required. The positive locking long life, and lowest insertion loss mechanism allows for easy field with maximum power handling tuning if frequency changes are capability. implemented. Heavy-duty materials are used The TPRD-9044 mounts on a 19" in construction of this duplexer, standard rack, with panel height of including silver-plated tuners and 5.25". Power handling is 250 watts. beryllium copper fingerstock Receiver desense protection is contactors, assuring high "Q" at least 80 dB, and TX sideband performance with no problems suppression is at least 80 dB. due to dissimilar metals. Tuning is simple and remains stable from -30º C to +70º C, thanks to the threaded Invar tuning rod. With TX to RX spacing of 5 MHz or more, this duplexer can combine two transmitters into one antenna, Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6010 Rev. 11/06 183 TPRD-9044 0 10 20 30 40 80 60 70 80 890 Attenuation in dB 890 - 960 MHz TYPICAL RESPONSE Fc Frequency (MHz) 960 ELECTRICAL SPECIFICATIONS Frequency range Frequency separation (typ. / min) Maximum input power Insertion loss (TX/RX to ant., typ) TX noise suppression at RX (min) RX attenuation at TX (min) TX-RX isolation for 5 MHz separation (min) VSWR (max) Impedance Temperature range Number of cavities MECHANICAL SPECIFICATIONS Cavity diameter in. (cm) Dimensions (HWD) in. (cm) Mounting Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 890-960 MHz 39 MHz / 3.6 MHz 250 watts 1.0 dB 80 dB 80 dB 70 dB 1.5:1 50 ohms -30°C to +70°C 4 4 (10) 5.25 x 19 x 10.5 (13 x 48 x 26.67) 19" Panel N Female Acrylic enamel 21 (9.6) 26 (11.8) Specify exact transmitter and receiver frequencies when ordering. 184 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6010 Rev. 11/06 TPRD-12044 PASS-REJECT DUPLEXER 1240 - 1300 MHz 6 DUPLEXERS The Telewave TPRD-12044 Base due to dissimilar metals. Tuning is The TPRD-12044 mounts on a 19" Station Duplexer provides high simple and remains stable from -30º standard rack, with panel height of performance and high reliability C to +70º C, thanks to the threaded 5.25". Power handling is 250 watts. for the 23 cm Amateur Radio band. Invar tuning rod. Receiver desense protection is With two Pass/Reject cavities in each transmitter and receiver path, these duplexers provide maximum TX to RX protection in dense RF environments. Adjustable coupling optimizes the required attenuation for ideal RX performance. All cavity inputs are electrically shorted to ground for maximum static and noise at least 80 dB, and TX sideband suppression is at least 80 dB. Typical spacing is 12 MHz. With TX to RX spacing of 6 MHz or more, this duplexer can also combine Mil-Spec semi-rigid cable is used protection. two transmitters into one antenna, for all interconnections to ensure long life, and lowest insertion loss with maximum power handling capability. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. No further adjustments should or feed two receivers. Frequency spacing and other requirements must be specified with all orders. Heavy-duty materials are used be required. The positive locking in construction of this duplexer, mechanism allows for easy field including silver-plated tuners and tuning if frequency changes are ber yllium copper fingerstock implemented. contactors, assuring high "Q" performance with no problems Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6032 Rev. 10/12 185 TPRD-12044 0 10 20 30 40 50 60 70 80 90 1263.80 Attenuation in dB 1240 - 1300 MHz TYPICAL RESPONSE 1276.30 Frequency (MHz) 1288.80 ELECTRICAL SPECIFICATIONS Frequency range 1240-1300 MHz Frequency separation (typ. / min) 12 MHz / 6 MHz Maximum input power 250 watts Insertion loss (TX/RX to ant., typ) 1.0 dB TX noise suppression at RX (min) 80 dB RX attenuation at TX (min) 80 dB TX-RX isolation for 6 MHz separation (min) 80 dB VSWR (max) 1.5:1 Impedance 50 ohms Temperature range -30°C to +70°C MECHANICAL SPECIFICATIONS Number of cavities (4) - 4" Dia. x 8" L Dimensions (HWD) in. (cm) 5.25 x 19 x 10.5 (13 x 48 x 26.67) Mounting 19" Panel Connectors N Female Finish Acrylic enamel Net weight lb. (kg) 21 (9.6) Shipping weight lb. (kg) 26 (11.8) NOTE: Exact transmitter and receiver frequencies must be specified. 186 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6032 Rev. 10/12 TPCD-8626 COMBLINE DUPLEXER 806 - 960 MHz 6 DUPLEXERS The Telewave TPCD-8626 Combline duplexer is specifically designed for use with 800 MHz master antenna systems, supporting trunking and conventional channels with excellent rejection of external noise sources. Maximum transmitterto-receiver protection is achieved across the full 806-821 and 851-866 MHz bands. The duplexer consists of two Telewave combline duplexers compact combline filters mounted offer the ultimate performance on a single 5.25" panel, and for trunking and conventional provides steep-skirt selectivity systems, providing protection with minimum insertion loss. All against receiver desensitization and units are tuned and tested with interference at congested sites. customer specified frequencies for optimum performance. No further field adjustment should be required. Attenuation in dB TYPICAL RESPONSE 0 10 20 30 40 50 60 70 -40 20 Fo +20 +40 +60 +80 +100 Frequency (MHz) ELECTRICAL SPECIFICATIONS Frequency range Frequency separation (min) Maximum input power TX or RX pass bandwidth Insertion loss at pass bandwidth (TX / RX) TX attenuation at RX band (min) RX attenuation at TX band (min) TX-to-RX attenuation (min) VSWR, ref. to 50 ohms (max) Temperature range MECHANICAL SPECIFICATIONS Mounting Dimensions HWD in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 806-960 MHz 45 MHz 350 watts 15 MHz typ /18 MHz max 1 dB max / 0.5 dB (typ) 85 dB 85 dB 75 dB 1.5:1 -30°C to +70°C 19" Panel 5.25 x 19 x 4.5 (13.3 x 48 x 11.4) N Female Clear alodine 9.5 (4.3) 14 (6.4) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6017 Rev. 3/16 187 TPCD-8626HP HIGH POWER COMBLINE DUPLEXER 806 - 960 MHz The Telewave TPCD-8626HP High Telewave High Power Combline Power Combline Duplexer handles Duplexers of fer the ultimate 500 watts, and is specially designed per formance in trunking and for 800 and 900 MHz master conventional systems, providing antenna systems which require high p rote c t io n a g a i n s t re cei ve r power handling, sharp selectivity, desensitization and interference at and very low insertion loss. This congested sites. duplexer supports systems with large frequency spreads, and ensures suppression of out-of-band emissions (OOBE). The TPCD-8626HP duplexer consists of two combline filters with 7-16 DIN connectors on both transmitter and antenna ports. The filters are mounted on a tray with a 19" x 5.25" front panel. All units are tuned to user-specified frequency bands for optimum performance. No further adjustment is required. 188 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6003 Rev. 12/10 TPCD-8626HP 806 - 960 MHz 6 DUPLEXERS Attenuation in dB TYPICAL RESPONSE 0 10 20 30 40 50 60 70 80 -45 -30 -15 Fo +15 +30 +45 Frequency (MHz) RF SPECIFICATIONS Frequency range Frequency separation (min) Maximum input power TX/RX pass bandwidth Insertion loss at pass bandwidth (TX and RX) TX attenuation at RX band (typ) RX attenuation at TX band (typ) TX to RX attenuation (min) VSWR, ref. to 50 ohms (max) Temperature range MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Mounting Connectors Antenna, TX input RX Output Panel finish Cavity finish Net weight lb. (kg) Shipping weight lb. (kg) 806-960 MHz 45 MHz 500 watts 15 MHz std. (10, 20,26 MHz opt.) 0.4 dB typ. / 0.75 dB max 85 dB 85 dB 85 dB 1.5:1 -30°C to +70°C 5.25 x 19 x 16 (13.3 x 48 x 40.6) 19" Panel 7-16 DIN N Female Clear alodine Gray enamel 15 (6.8) 19.5 (8.9) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6003 Rev. 12/10 189 TMND-0716, 0816 MID-BAND COMPACT DUPLEXERS Telewave TMND - 0716/0816 Mobile Duplexers provide high performance in a compact design. These rugged duplexers are designed for use in base or mobile installations, with minimum space requirements. Each duplexer consists of six High "Q" helical resonators in a band-reject configuration. This compact design has no exposed interconnect cables. Field tuning can be performed with easily accessible tuning elements on the rear of the unit. The TMND-0716 and 0816 are All duplexers are tuned and designed to operate with at least tested with customer-specified 4 MHz TX to RX separation. This frequencies prior to shipping. When configuration provides 75 dB of ordering, specify exact frequencies isolation, and low insertion loss and connector type required (N or permits power handling up to 50 BNC). watts. 70 - 85 MHz TMND-0716 70-78 MHz TMND-0816 77-85 MHz ELECTRICAL SPECIFICATIONS Frequency range (MHz) Frequency separation (min) Maximum input power Impedance / VSWR (max) Insertion loss (TX/RX to-antenna) TX noise at RX (min) RX attenuation at TX (min) TX-RX Iso. at 4 MHz sep. (min) Temperature range Resonators MECHANICAL SPECIFICATIONS Dimensions (HWL) in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 0716: 70-78 0816: 77-85 4 MHz 50 watts 50 ohms / 1.5:1 1.2 dB 75 dB 75 dB 75 dB -20°C to +60°C (6) - 1" 1.2 x 6.1 x 5.4 (3 x 15.5 x 13.7) N or BNC Acrylic enamel 2.2 (1) 3.0 (1.4) Attenuation in dB TYPICAL RESPONSE 0 10 20 30 40 50 60 70 80 75 81 87 Frequency (MHz) Appearance of current production models may vary from picture. 190 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6021 Rev. 11/06 DUPLEXERS TMND-1516, 1616, 1716 VHF COMPACT DUPLEXERS Telewave TMND -15/16/1716 Mobile Duplexers provide high performance in a compact design. These rugged duplexers are designed for use in base or mobile installations, with minimum space requirements. Each duplexer consists of six High "Q" helical resonators in a band-reject configuration. This compact design has no exposed interconnect cables. Field tuning can be performed with easily accessible tuning elements on the rear of the unit. The TMND-15/16/1716 operate with All duplexers are tuned and at least 4 MHz TX to RX separation. tested with customer-specified This configuration provides 75 dB frequencies prior to shipping. When of isolation, and low insertion loss ordering, specify exact frequencies permits power handling up to 50 and connector type required (N or watts. BNC). 148 - 174 MHz TMND-1516 148-157 MHz TMND-1616 156-165 MHz TMND-1716 164-174 MHz 6 ELECTRICAL SPECIFICATIONS Frequency range (MHz) Frequency separation (min) Maximum input power Impedance / VSWR (max) Insertion loss (TX/RX to-antenna) TX noise at RX (min) RX attenuation at TX (min) TX-RX Iso. at 4 MHz sep. (min) Temperature range Resonators MECHANICAL SPECIFICATIONS Dimensions (HWL) in. (cm) Footprint (mounting plate) in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 1516: 148-157 1716: 164-174 1616: 156-165 4 MHz 50 watts 50 ohms / 1.5:1 1.4 dB 75 dB 75 dB 75 dB -20°C to +60°C (6) - 1" 1.4 x 4.5 x 6.9 (3.5 x 11.4 x 17.5) 6.1 x 8.5 (16 x 22) BNC Female or N Female Black acrylic enamel 2.2 (1) 3.0 (1.4) Attenuation in dB 0 10 20 30 40 50 60 70 80 156.0 TYPICAL RESPONSE 160.0 Frequency (MHz) 165.0 Appearance of current production models may vary from picture. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6022 Rev. 10/12 191 TMND-4416, 4516, 4616 UHF COMPACT DUPLEXERS Telewave TMND - 44/45/4616 Mobile Duplexers provide high performance in a compact design. These rugged duplexers are designed for use in base or mobile installations, with minimum space requirements. Each duplexer consists of six High "Q" helical resonators in a band-reject configuration. This compact design has no exposed interconnect cables. Field tuning can be performed with easily accessible tuning elements on the rear of the unit. The TMND-44/45/4616 operate All duplexers are tuned and with at least 5 MHz TX to RX tested with customer-specified separation. This configuration frequencies prior to shipping. When provides 75 dB of isolation, and ordering, specify exact frequencies low insertion loss permits power and connector type required (N or handling up to 50 watts. BNC). 440 - 470 MHz TMND-4416 440-450 MHz TMND-4516 450-460 MHz TMND-4616 460-470 MHz ELECTRICAL SPECIFICATIONS Frequency range (MHz) Frequency separation (min) Maximum input power Impedance / VSWR (max) Insertion loss (TX/RX to antenna) TX noise at RX (min) RX attenuation at TX (min) TX-RX Iso. at 5 MHz sep. (min) Temperature range Resonators MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Footprint (mounting plate) in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 4416: 440-450 4616: 460-470 4516: 450-460 5 MHz 50 watts 50 ohms / 1.5:1 1.2 dB 75 dB 75 dB 75 dB -20°C to +60°C (6) - 1" 1.3 x 6.1 x 6.9 (3.3 x 15.5 x 17.5) 6.1 x 8.5 (16 x 22) BNC Female or N Female Black acrylic enamel 2.2 (1) 3.0 (1.4) Attenuation in dB TYPICAL RESPONSE 0 10 20 30 40 50 60 70 80 450.0 460.0 Frequency (MHz) 470.0 Appearance of current production models may vary from picture. 192 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6023 Rev. 11/06 DUPLEXERS TMND-4716, 4816, 4916, 5016 UHF COMPACT DUPLEXERS Telewave Mobile Duplexers provide high performance in a compact design. These rugged duplexers are designed for use in base or mobile installations, with minimum space requirements. Each duplexer consists of six High "Q" helical resonators in a band-reject configuration. This compact design has no exposed interconnect cables. Field tuning can be performed if needed with easily accessible tuning elements on the rear of the unit. Each duplexer covers a 10 MHz segment between 470-512 MHz, All duplexers are tuned and with t ypical 5 MHz T X to R X tested with customer-specified separation. This configuration frequencies prior to shipping. When provides 70 dB of isolation, and ordering, specify exact frequencies low insertion loss permits power and connector type required (N or handling up to 50 watts. BNC). 470 - 512 MHz TMND-4716 470-480 MHz TMND-4816 480-490 MHz TMND-4916 490-500 MHz TMND-5016 500-512 MHz 6 ELECTRICAL SPECIFICATIONS Frequency range (MHz) Frequency separation (typ) Maximum input power Impedance / VSWR (max) Insertion loss (TX/RX to antenna) TX noise at RX (min) RX attenuation at TX (min) TX-RX Iso. at 5 MHz sep. (min) Temperature range Resonators 470-512 MHz (10 MHz segment) 5 MHz (3 MHz - Contact Telewave) 50 watts 50 ohms / 1.5:1 1.25 dB 70 dB 70 dB 70 dB -20°C to +60°C (6) - 1" Attenuation in dB TYPICAL RESPONSE 0 10 20 30 40 50 60 70 80 470.0 473.0 Frequency (MHz) 476.0 MECHANICAL SPECIFICATIONS Dimensions (HWD) in. (cm) Footprint (mounting plate) in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 1.3 x 6.1 x 6.9 (3.3 x 15.5 x 17.5) 6.1 x 8.5 (16 x 22) BNC Female or N Female Black acrylic enamel 2.2 (1) 3.0 (1.4) Appearance of current production models may vary from picture. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6027 Rev. 6/13 193 769 - 805 MHz TMND-7616 700 MHZ COMPACT DUPLEXER The Telewave TMND-7616 Compact Mobile Duplexer is a perfect complement to high performance mobile data systems running on 12.5 and 25 KHz channels. The TMND-7616 covers 769-775 and 799-805 MHz with full 6 MHz band rejection. The compact size and form factor allow easy integration with any radio layout in all types of vehicles. Each duplexer consists of six High "Q" helical resonators in a bandreject configuration. Field tuning can be performed if needed with easily accessible tuning elements on the rear of the unit. The TMND-7616 operates with at least 30 MHz TX to RX separation. This configuration provides 67 dB of isolation, with low insertion loss. All duplexers are tuned and tested prior to shipping. N female connectors are standard. ELECTRICAL SPECIFICATIONS Frequency range (MHz) Frequency separation (min) Input power Impedance / VSWR (max) Insertion loss (TX/RX to antenna) TX noise at RX (min) RX attenuation at TX (min) TX-RX Iso. at 30 MHz sep. (min) Temperature range Resonators MECHANICAL SPECIFICATIONS Dimensions (HWL) in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 769-775 / 799-805 30 MHz 25 watts 50 ohms / 1.5:1 1.2 dB 67 dB 67 dB 67 dB -20°C to +60°C (6) - 1" 1.25 x 6.0 x 6.5 (3.2 x 15.2 x 16.5) BNC Female or N Female Black acrylic enamel 2.0 (0.9) 3.0 (1.4) Attenuation in dB TYPICAL RESPONSE 0 10 20 30 40 50 60 70 80 750 769-775 782.5 799-805 815 Frequency (MHz) Appearance of current production models may vary from picture. 194 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6013 Rev. 5/13 DUPLEXERS TMND-8616 800 MHZ COMPACT DUPLEXER The Telewave TMND-8616 Compact Mobile Duplexer provides high performance in a compact design. This rugged duplexer is designed for use in base or mobile installations, with minimum space requirements. Each duplexer consists of six High "Q" helical resonators in a bandreject configuration. Field tuning can be performed if needed with easily accessible tuning elements on the rear of the unit. The TMND-8616 operates with typical 45 MHz TX to RX separation. This configuration provides 70 dB of isolation, and power handling up to 50 watts with low insertion loss. All duplexers are tuned and tested with customer-specified frequencies prior to shipping. When ordering, specify exact frequencies and connector type required (N or BNC). 806 - 869 MHz 6 ELECTRICAL SPECIFICATIONS Frequency range Frequency separation (min / typ) Maximum input power Impedance / VSWR (max) Insertion loss (TX/RX to-antenna) TX noise at RX (min) RX attenuation at TX (min) TX-RX Iso. at 5 MHz sep. (min) Temperature range Resonators MECHANICAL SPECIFICATIONS Dimensions (HWL) in. (cm) Connectors Finish Net weight lb. (kg) Shipping weight lb. (kg) 806-869 MHz 5 / 45 MHz 50 watts 50 ohms / 1.5:1 1.0 dB 70 dB 70 dB 70 dB -20°C to +60°C (6) - 1" 1.25 x 6.0 x 6.5 (3.2 x 15.2 x 16.5) BNC Female or N Female Black acrylic enamel 2.0 (0.9) 3.0 (1.4) Attenuation in dB TYPICAL RESPONSE 0 10 20 30 40 50 60 70 80 800.0 840.0 880.0 Frequency (MHz) Appearance of current production models may vary from picture. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-6011 Rev. 10/10 195 7 BASE STATION ANTENNAS 7 BASE STATION ANTENNAS Fiberglass Collinear Collinear antennas provide a consistent omnidirectional pattern with no external ground plane components. Advanced engineering produces significant gain and frequency range options. Fiberglass composite radomes offer complete protection from severe environments. Folded Dipole Telewave Broadband Folded Dipole antennas can be configured for several different horizontal patterns, depending on coverage requirements. Cardiod, offset, and bi-directional patterns are easily produced by adjusting element spacing during or after installation. Dipole Arrays Dipole arrays use multiple elements to compress the vertical pattern, providing more gain in a particular direction or protection to or from a nearby system. Electrical and mechanical tilt of 1-15 degrees is possible with two to eight elements. Yagi Yagi antennas are rugged, compact devices which produce a very directional horizontal pattern. These antennas are fully sealed and are ideal for control and linking applications. Wideband Wideband antennas cover very wide frequency ranges, in discone and handheld configurations. Discone antennas also provide a broad radiation pattern and consistent VSWR. Power Dividers RF Power Dividers split a single input into 2, 3, or 4 outputs with impedance matching to ensure 50 ohms at all ports. These dividers handle up to 500 watts of power with no port isolation. Crossband Couplers Crossband couplers allow radios in multiple frequency bands to connect to appropriate antennas with a single cable run and very low insertion loss. A pair of devices is typically used for this application, or a single device can couple multiple radios to a single broadband antenna. COLLINEAR ANTENNAS 118 - 965 MHz Telewave COOL BLUETM fiberglass collinear antennas are an industry standard. These antennas are specified by system designers who require their unique combination of wide bandwidth, high performance, gain flexibility, and rugged durability in all environmental conditions. All Telewave collinear antennas handle 500 watts minimum input power, and are available in eight major frequency bands between 118-965 MHz, with gain from 0 to 10 dBd. Horizontal patterns are omnidirectional, and vertical beamwidth ranges from 7 to 42 degrees depending on gain and frequency. The Telewave collinear design does not require external ground plane radials, eliminating a major source of failure and RF intermodulation. These antennas are constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection, including a solid copper or brass top cap. All junctions are fully soldered to prevent intermodulation. A heavy-duty 2.75" support pipe made of 6061-T6 aluminum is permanently bonded to an exceptionally strong radome, ensuring years of trouble-free performance. The COOL BLUETM interwoven fiberglass radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. Wind-load ratings are up to 200 MPH with no ice, and the flexibility of the radome (F6/8/10 models) allows enough antenna motion to resist normal icing, without affecting the pattern. The special radome color helps the antenna blend into the skyline, and absorbs solar radiation to accelerate de-icing. The standard connector type is a recessed N-female, attached inside the base of the support pipe. A 24" coax jumper is included to simplify installations using hard-line cable. For higher power applications, a 7-16 DIN-F connector can be installed as an option. One set of heavy-duty mounting clamps is included with each antenna. 198 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7035 Rev. 10/07 COLLINEAR ANT125F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd 118 - 136 MHz 7 The Telewave ANT125F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to DC ground for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT125F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT125F2 - 127 MHz Vertical Plane Gain = 2.56 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 118-136 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 77 x 2.75 16 lb. 20 lb. 200 / 150 MPH 1.6 ft.² 62 lb. 117 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7051 Rev. 1/11 199 125 - 150 MHz ANT135F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd The Telewave ANT135F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to DC ground for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT135F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 -90 ANT135F2 - 137 MHz Vertical Plane Gain = 2.53 dBd -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 125-150 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 72 x 2.75 15 lb. 19 lb. 200 / 150 MPH 1.5 ft.² 59 lb. 101 ft. lb. 200 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7059 Rev. 1/11 COLLINEAR ANT140F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd 135 - 165 MHz 7 The Telewave ANT140F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT140F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 -30 -60 -90 ANT140F2 - 150 MHz Vertical Plane Gain = 2.51 dBd 60 30 0 -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 135-165 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 66 x 2.75 13 lb. 17 lb. 200 / 150 MPH 1.4 ft.² 55 lb. 83 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7047 Rev. 1/11 201 148 - 174 MHz ANT150F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd The Telewave ANT150F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to DC ground for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT150F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 -30 -60 -90 ANT150F2 156 MHz Vertical Plane Gain = 2.55 dBd 60 30 0 -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 148-174 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 60 x 2.75 12 lb. 16 lb. 200 / 150 MPH 1.3 ft.² 50 lb. 67 ft. lb. 202 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7017 Rev. 1/11 COLLINEAR ANT150F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd 138 - 175 MHz 7 The Telewave ANT150F6 is an extremely rugged, medium-gain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a high-tech, flexible radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, UV radiation, icing, salt spray, acid rain, and wind blown abrasives. Eight models cover the entire VHF band. Please specify exact frequency and band code (-1, -2, etc.) when ordering. The ANT150F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. NOTE: THESE ANTENNAS ARE SHIPPED VIA TRUCK FREIGHT ONLY 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 -90 ANT150F6 - 156 MHz Vertical Plane Gain = 6.41 dBd -30 -60 FREQUENCY RANGES ANT150F6-1 138 - 144 MHz ANT150F6-2 144 - 151 MHz ANT150F6-3 150 - 157 MHz ANT150F6-4 156 - 164 MHz ANT150F6-5 158 - 166 MHz ANT150F6-6 161 - 168 MHz ANT150F6-7 167 - 172.5 MHz ANT150F6-8 171 - 175 MHz SPECIFICATIONS Frequency range Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 138-175 MHz (8 bands) 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 20° Recessed N Female 7-16 DIN-F opt. 138-151 MHz 150-175 MHz Dimensions (L x base diam.) 256" x 2.75" 244" x 2.75" Tower weight (Antenna + clamps) 43 lb. 41 lb. Shipping weight 65 lb. 62 lb. Wind rating / 0.5" ice 150 / 125 MPH Maximum exposed area 4.05 ft.² 3.97 ft.² Lateral Thrust at 100 MPH 162 lb. 159 lb. Bending Moment - top clamp 1090 ft. lb. 1010 ft. lb. (100 MPH, 40 PSF flat plate equiv.) Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7020 Rev. 5/12 203 174 - 216 MHz ANT195F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd The Telewave ANT195F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. The ANT195F2 is an excellent choice for SCADA or other whitespace applications, and DTV translators. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT195F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT195F2 - 195 MHz Vertical Plane Gain = 2.52 dBd 174 195 220 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 174-216 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 53 x 2.75 11 lb. 15 lb. 200 / 150 MPH 1.2 ft.² 46 lb. 54 ft. lb. 204 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7122 Rev. 10/13 COLLINEAR ANT220F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd 195 - 260 MHz 7 The Telewave ANT220F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. The ANT220F2 is an excellent choice for wireless PTC systems in urban or rural areas. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT220F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT220F2 - 230 MHz Vertical Plane Gain = 2.58 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 195-260 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 51 x 2.75 11 lb. 14 lb. 200 / 150 MPH 1.1 ft.² 44 lb. 47 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7053 Rev. 1/11 205 216 - 225 MHz ANT220F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd The Telewave ANT220F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. The ANT220F6 is an excellent choice for wireless PTC systems in urban or rural areas. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT220F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 -90 ANT220F6 - 221 MHz Vertical Plane Gain = 6.11 dBd -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 216-225 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 20° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 171 x 2.75 35 lb. 50 lb. 150 / 125 MPH 3.1 ft.² 122 lb. 494 ft. lb. 206 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7021 Rev. 1/11 COLLINEAR ANT355F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd 340 - 370 MHz 7 The Telewave ANT355F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT355F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT355F6 - 355 MHz Vertical Plane Gain = 6.27 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 340-370 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 18° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 126 x 2.75 26 lb. 37 lb. 150 / 125 MPH 2.5 ft.² 99 lb. 263 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7094 Rev. 1/11 207 370 - 400 MHz ANT385F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd The Telewave ANT385F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT385F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 -90 ANT385F6 - 385 MHz Vertical Plane Gain = 6.12 dBd -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 370-400 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 18° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 112 x 2.75 24 lb. 35 lb. 150 / 125 MPH 2.3 ft.² 91 lb. 205 ft. lb. 208 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7095 Rev. 1/11 COLLINEAR ANT400F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd 360 - 455 MHz 7 The Telewave ANT400F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT40 0F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 -30 -60 -90 ANT400F2 - 410 MHz Vertical Plane Gain = 2.51 dBd 60 30 0 -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 360-455 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 44 x 2.75 9 lb. 11 lb. 200 / 150 MPH 1.0 ft.² 39 lb. 33 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7072 Rev. 1/11 209 405 - 440 MHz ANT415F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd The Telewave ANT415F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT415F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 -90 ANT415F6 - 421 MHz Vertical Plane Gain = 6.7 dBd -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 405-440 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 18° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 101 x 2.375 22 lb. 28 lb. 185 / 155 MPH 1.7 ft.² 68 lb. 149 ft. lb. 210 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7030 Rev. 1/11 COLLINEAR ANT415F8 FIBERGLASS COLLINEAR ANTENNA 8 dBd The Telewave ANT415F8 is an extremely rugged, high-gain fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT415F8 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 60 30 0 90 -3 -10 -20 -30 -60 -90 ANT415F8 - 420 MHz Vertical Plane Gain = 8.68 dBd 395 - 436 MHz 7 60 30 0 -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 395-436 MHz 8 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 11° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 240 x 2.75 40 lb. 60 lb. 150 / 125 MPH 3.9 ft.² 157 lb. 975 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7022 Rev. 1/11 211 380 - 470 MHz ANT425F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd The Telewave ANT425F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT425F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 -30 -60 -90 ANT425F2 - 425 MHz Vertical Plane Gain = 2.56 dBd 60 30 0 -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 380-470 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 42 x 2.75 9 lb. 11 lb. 200 / 150 MPH 1.0 ft.² 38 lb. 30 ft. lb. 212 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7104 Rev. 1/11 COLLINEAR ANT450F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd 420 - 480 MHz 7 The Telewave ANT450F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT450F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT450F2 - 447 MHz Vertical Plane Gain = 2.54 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 420-480 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 42 x 2.75 9 lb. 11 lb. 200 / 150 MPH 1.0 ft.² 38 lb. 30 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7018 Rev. 1/11 213 445 - 480 MHz ANT450F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd The Telewave ANT450F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT450F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 -30 -60 -90 ANT450F6 - 460 MHz Vertical Plane Gain = 6.32 dBd 60 30 0 -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 445-480 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 18° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 94 x 2.375 21 lb. 26 lb. 150 / 125 MPH 1.5 ft.² 60 lb. 143 ft. lb. 214 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7036 Rev. 1/11 COLLINEAR ANT450F10 FIBERGLASS COLLINEAR ANTENNA 10 dBd 430 - 475 MHz 7 The Telewave ANT450F10 is an extremely rugged, high-gain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT450F10 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT450F10 - 450 MHz Vertical Plane Gain = 10.06 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 430-475 MHz 10 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 7° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 244 x 2.75 41 lb. 62 lb. 150 / 125 MPH 4.0 ft.² 159 lb. 1010 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7037 Rev. 1/11 215 450 - 512 MHz ANT480F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd The Telewave ANT480F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT480F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 -30 -60 -90 ANT480F2 - 487 MHz Vertical Plane Gain = 2.51 dBd 60 30 0 -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 450-512 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 42 x 2.75 9 lb. 11 lb. 200 / 150 MPH 1.0 ft.² 38 lb. 30 ft. lb. 216 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7078 Rev. 1/11 COLLINEAR ANT500F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd 470 - 512 MHz 7 The Telewave ANT500F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT500F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT500F6 - 490 MHz Vertical Plane Gain = 6.28 dBd TYPICAL VSWR RESPONSE 1.5:1 1.4:1 1.3:1 1.2:1 1.1:1 470 491 512 FREQUENCY (MHz) SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 470-512 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 19° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 89 x 2.375 20 lb. 25 lb. 150 / 125 MPH 1.4 ft.² 57 lb. 127 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7049 Rev. 1/11 217 470 - 512 MHz ANT500F10 FIBERGLASS COLLINEAR ANTENNA 10 dBd The Telewave ANT500F10 is an extremely rugged, high-gain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT500F10 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT500F10 - 495 MHz Vertical Plane Gain = 10.06 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 470-512 MHz 10 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 7° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 244 x 2.75 41 lb. 62 lb. 150 / 125 MPH 4.0 ft.² 159 lb. 1010 ft. lb. 218 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7050 Rev. 1/11 COLLINEAR ANT734-960F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd 734 - 960 MHz 7 The Telewave ANT734-960F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact, wideband antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT734-960F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT734-960F2 - 838 MHz Vertical Plane Gain = 2.5 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 734-960 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 38 x 2.75 8 lb. 10 lb. 200 / 150 MPH 0.9 ft.² 35 lb. 23 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7056 Rev. 1/11 219 734 - 806 MHz ANT770F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd The Telewave ANT770F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT770F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT770F2 - 750 MHz Vertical Plane Gain = 2.5 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 734-806 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 38 x 2.75 8 lb. 10 lb. 200 / 150 MPH 0.9 ft.² 35 lb. 23 ft. lb. 220 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7052 Rev. 1/11 COLLINEAR ANT770F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd 746 - 806 MHz 7 The Telewave ANT770F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT770F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT770F6 - 776 MHz Vertical Plane Gain = 6.15 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 746-806 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 19° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 61 x 2.375 19 lb. 23 lb. 200 / 150 MPH 1.1 ft.² 42 lb. 55 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7086 Rev. 4/13 221 745 - 860 MHz ANT825F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd The Telewave ANT825F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT825F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT825F6 - 800 MHz Vertical Plane Gain = 6.09 dBd 745 805 860 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 745-860 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 19° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 59 x 2.75 18 lb. 22 lb. 200 / 150 MPH 1.05 ft.² 41 lb. 52 ft. lb. 222 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7109 Rev. 4/13 COLLINEAR ANT850F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd 806 - 896 MHz 7 The Telewave ANT850F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT850F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT850F2 - 851 MHz Vertical Plane Gain = 2.58 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 806-896 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 38 x 2.75 8 lb. 10 lb. 200 / 150 MPH 0.9 ft.² 35 lb. 23 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7054 Rev. 1/11 223 806 - 896 MHz ANT850F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd The Telewave ANT850F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT850F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 -90 ANT850F6 - 850 MHz Vertical Plane Gain = 6.16 dBd -30 -60 SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 806-896 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 19° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 56 x 2.375 18 lb. 22 lb. 200 / 150 MPH 1.0 ft.² 39 lb. 46 ft. lb. 224 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7010 Rev. 1/11 COLLINEAR ANT850F10 FIBERGLASS COLLINEAR ANTENNA 10 dBd 806 - 896 MHz 7 The Telewave ANT850F10 is an extremely rugged, high-gain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT850F10 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT850F10 - 850 MHz Vertical Plane Gain = 10.10 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 806-896 MHz 10 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 6° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 83 x 2.375 19 lb. 23 lb. 200 / 150 MPH 1.3 ft.² 53 lb. 106 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7011 Rev. 1/11 225 880 - 960 MHz ANT900F2 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd The Telewave ANT900F2 is an extremely rugged collinear antenna, with moderate gain and wide vertical beamwidth. This compact antenna produces 2.5 dBd gain, and is designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, with a path to ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT900F2 includes the ANTC485 dual clamp set for mounting to a 1.5" to 3" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT900F2 - 928 MHz Vertical Plane Gain = 2.5 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 880-960 MHz 2.5 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 38° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 38 x 2.75 8 lb. 10 lb. 200 / 150 MPH 0.9 ft.² 35 lb. 23 ft. lb. 226 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7055 Rev. 1/11 COLLINEAR ANT940F6 FIBERGLASS COLLINEAR ANTENNA 6 dBd 870 - 965 MHz 7 The Telewave ANT940F6 is an extremely rugged, mediumgain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT940F6 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT940F6 - 930 MHz Vertical Plane Gain = 6.1 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 870-965 MHz 6 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 19° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 56 x 2.375 18 lb. 22 lb. 200 / 150 MPH 1.0 ft.² 39 lb. 46 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7012 Rev. 1/11 227 870 - 965 MHz ANT940F10 FIBERGLASS COLLINEAR ANTENNA 10 dBd The Telewave ANT940F10 is an extremely rugged, high-gain, fiberglass collinear antenna, designed for operation in all environmental conditions. The antenna is constructed with brass and copper elements, connected at DC ground potential for lightning impulse protection. All junctions are fully soldered to prevent RF intermodulation, and each antenna is completely protected within a rugged, hightech radome to ensure survivability in the worst environments. The "Cool Blue" radome provides maximum protection from corrosive gases, ultraviolet radiation, icing, salt spray, acid rain, and wind blown abrasives. The ANT940F10 includes an ANTC482 dual clamp set for mounting to a 1.5" to 3.5" O.D. support pipe, and a 24" removable RG-213 N-Male jumper. Stand-off and top mounts are also available. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 -60 -60 -90 ANT940F10 - 930 MHz Vertical Plane Gain = 10.12 dBd SPECIFICATIONS Frequency (continuous) Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 870-965 MHz 10 dBd 500 watts 50 ohms 1.5:1 or less Omnidirectional 6° Recessed N Female 7-16 DIN-F opt. Dimensions (L x base diam.) in. Tower weight (antenna + clamps) Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 83 x 2.375 19 lb. 23 lb. 200 / 150 MPH 1.4 ft.² 55 lb. 112 ft. lb. 228 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7013 Rev. 1/11 COLLINEAR ANT960F0 WIRELESS DATA ANTENNA 2 dBd The Telewave ANT960F0 "Data 90 Stick" is a rugged, economical omni antenna for wireless data 60 60 -3 applications in the 900 MHz band. 30 -10 30 The antenna is constructed entirely -20 from brass internal components, and the durable radome is designed 0 0 to withstand severe weather and environmental conditions. The radome will not corrode or -30 -30 degrade as a result of exposure to UV, salt water, oil, or most common -60 -60 chemical fumes. Optional mounting hardware is available for various applications. -90 ANT960F0 - 915 MHz Vertical Plane Gain = 2.0 dBd 900 - 960 MHz ANT960F0-1 900-930 MHz ANT960F0-2 920-960 MHz 7 Shown with optional clamp SPECIFICATIONS Frequency range Gain Power rating (typ.) Impedance VSWR Pattern Vertical beamwidth Termination 900-930 / 920-960 MHz 2 dBd 50 watts 50 ohms 1.5:1 or less Omnidirectional 42° Recessed N-Male Dimensions (L x base diam.) in. Antenna weight Shipping weight Wind rating / with 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at top clamp (100 MPH, 40 PSF flat plate equiv.) 14.5 x 1 1 lb. 3 lb. 90 / 90 MPH 0.1 ft.² 4 lb. 2 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7039 Rev. 1/11 229 118 - 960 MHz INSTALLATION GUIDE FOR COLLINEAR ANTENNAS F2 MODELS WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. IMPORTANT - BEFORE ASSEMBLING AND MOUNTING: Carefully read these instructions and study the diagrams. Check to make sure you have all parts. Both clamps must be installed and properly spaced to prevent antenna rotation from wind load. Figure 1: ANTC485 Clamp Kit PARTS LIST (1) Antenna assembly (1) Jumper RG-213 N-male to N-male 24" (provided only with N-terminated antennas) (1) ANTC485 clamp kit Clamp Kit Contents (Figure 1): (2) Clamp plates (2) 3/8"-16 stainless U bolts (4) Hex nuts (4) Lock washers (1) Anti-seize compound Figure 2: Typical Mounting Configuration MOUNTING INSTRUCTIONS 1. The welded mounting rails are intended to be placed against the support structure when used with the supplied clamp set. When using an ANTC483 or other clamp set, the mounting rails should be turned to one side, out of contact with the support. 2. Apply anti-seize compound to ends of u-bolts. Place a loosely assembled clamp over the top of the mast. Feed the antenna base ferrule down through the clamp until aligned with the upper attachment point. Tighten down the hex nuts and straighten the antenna until clamped into a vertical position. 3. Attach and secure the lower antenna clamp with supplied hex nuts and lock washers, to provide reasonable pressure to the support structure and antenna base ferrule (Figure 2). 4. The antenna input connector is a Type N or 7-16 DIN Female. A 24" N-male jumper is provided for antennas with N input. Connect RF feed cable terminated with Type N or 7-16 DIN as required to antenna input connector. Secure all cables with cable ties. 5. Be sure to properly seal the input connector with waterproof tape or other sealing material. See Telewave TWDS-0502 for a recommended method of connector sealing. 230 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7084 Rev. 4/11 INSTALLATION GUIDE 7 FOR COLLINEAR ANTENNAS F6, F8, AND F10 MODELS COLLINEAR WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. IMPORTANT - BEFORE ASSEMBLING AND MOUNTING: Carefully read these instructions and study the diagrams. Check to make sure you have all parts. The antenna and clamp kit are packaged as two separate items. Both clamps must be installed and properly spaced to prevent antenna rotation from wind load. Figure 1: Clamp Set Contents NOTE: To prevent possible damage to the ferrule and radome, tighten all nuts only until the lock washers are flattened. Then add 1/2 turn to each. PARTS LIST (1) Antenna assembly (1) Jumper RG-213 N-male to N-male 24" (provided only with N-terminated antennas) (1) ANTC482 clamp kit Clamp kit Contents (figure 1): (8) galvanized clamp plates (4) 1/2"-13 x 10" stainless steel threaded rods (16) 1/2" stainless steel hex nuts (16) 1/2" stainless steel split lock washers (1) Anti-seize compound Figure 2: Clamp Preassembly MOUNTING INSTRUCTIONS 1. Apply anti-seize compound to threaded rod ends. Insert rods through dual clamps with hex nuts and lock washers in the middle of the clamps as shown in figure 2. Mount both clamps to the support structure with 2 single clamp plates, hex nuts, and lock washers. Arrange clamps so that 1"-2" of ferrule is exposed above and below the clamps. Be sure to allow sufficient thread length on the antenna side of the clamps. 2. Attach antenna clamp plate to the upper clamp set only, allowing maximum plate movement on the rods. Feed the antenna base ferrule down through the clamp until aligned with the upper attachment point. Partially tighten the hex nuts and straighten the antenna until clamped into a vertical position. 3. Attach and secure the lower antenna clamp with supplied hex nuts and lock washers, and tighten both clamps until the lock washers are flat plus 1/2 turn additional on each nut. (Figure 3). 4. The antenna input connector is a Type N or 7-16 DIN Female. A 24" N-male jumper is provided for antennas with N input. Connect RF feed cable terminated with Type N or 7-16 DIN as required to antenna input connector. Secure all cables with cable ties. 5. Be sure to properly seal the input connector with waterproof tape or other sealing material. See Telewave TWDS-0502 for a recommended method of connector sealing. Figure 3: Assembly Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7083 Rev. 4/11 231 ANTC482 CLAMP SET FOR COLLINEAR ANTENNAS WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. IMPORTANT - BEFORE ASSEMBLING AND MOUNTING: Carefully read these instructions and study the diagrams. Check to make sure you have all parts. The antenna and clamp kit are packaged as two separate items. Both clamps must be installed and properly spaced to prevent antenna rotation from wind load. NOTE: To prevent possible damage to the ferrule and radome, tighten all nuts only until the lock washers are flattened. Then add 1/2 turn to each. PARTS LIST (Figure 1) (8) galvanized clamp plates (4) 1/2"-13 x 10" stainless steel threaded rods (16) 1/2" stainless steel hex nuts (16) 1/2" stainless steel split lock washers (1) Anti-seize compound MOUNTING INSTRUCTIONS Apply anti-seize compound to threaded rod ends. Insert rods through dual clamps with hex nuts and lock washers in the middle of the clamps as shown in figure 2. Mount both clamps to the support structure with 2 single clamp plates, hex nuts, and lock washers. Arrange clamps so that 1"-2" of ferrule is exposed above and below the clamps. Be sure to allow sufficient thread length on the antenna side of the clamps.. Tighten clamps only until lockwashers are flat, then add ½ turn additional on each nut. Figure 1: Clamp Set Contents Figure 2: Clamp Preassembly Figure 3: Assembly Antenna Base Dimensional Data: ANTC482 can be attached to square or round tower legs from 1.5" to 3.5" O.D. Clamp holes are 9/16" diameter, and 4.75" inches center to center. Mast or Support Structure 232 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7093 Rev. 10/13 COLLINEAR ANTC483/483SS CLAMP SET 7 FOR COLLINEAR ANTENNAS WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. IMPORTANT - BEFORE ASSEMBLING AND MOUNTING: Carefully read these instructions and study the diagrams. Check to make sure you have all parts. The antenna and clamp kit are packaged as two separate items. Both clamps must be installed and properly spaced to prevent antenna rotation from wind load. NOTE: To prevent possible damage to the ferrule and radome, tighten all nuts only until the lock washers are flattened. Then add 1/2 turn to each. PARTS LIST (Figure 1) (4) Tower or antenna (single) galvanized clamp plates (2) Welded (dual) galvanized clamp plates (4) 1/2"-13 x 10" stainless steel threaded rods (12) 1/2" stainless steel hex nuts (8) 1/2" stainless steel split lock washers (1) Anti-seize compound MOUNTING INSTRUCTIONS Apply anti-seize compound to threaded rod ends. Insert rods through dual clamps with hex nuts and lock washers in the middle of the clamps as shown in figure 2. Mount both clamps to the support structure with 2 single clamp plates, hex nuts, and lock washers. Arrange clamps so that 1"-2" of ferrule is exposed above and below the clamps. Be sure to allow sufficient thread length on the antenna side of the clamps. Tighten clamps only until lockwashers are flat, then add ½ turn additional on each nut. Figure 1: Clamp Set Contents Figure 2: Clamp Preassembly Figure 3: Assembly (end view) Antenna Base Dimensional Data: ANTC483 and 483SS can be attached to square or round tower legs from 1.5" to 3.5" O.D. Clamp holes are 9/16" diameter, and 4.75" inches center to center. Mast or Support Structure Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7085 Rev. 10/13 233 DIPOLE ANTENNAS 30 - 1000 MHz Telewave Dipole and Dipole Array antennas are built in the USA to withstand harsh conditions in the most demanding applications. Telewave dipoles are in service on mountaintops in Alaska, oil rigs in the Gulf of Mexico, Phillipine jungles, and the deserts of North Africa. Constructed from 6061-T6 aluminum, Telewave Dipoles feature broad bandwidth, and superior lightning impulse protection thanks to direct DC ground construction. Telewave dipole antennas and arrays also feature a high-tech coating called TxylanTM, which completely encapsulates all metal antenna components, providing total protection from water, corrosive chemicals, salt spray, and windblown abrasives. This smooth black coating also dramatically reduces surface friction, reducing and often preventing ice adhesion, while improving absorption of solar radiation. All cabling is Mil-Spec RG-213/U, and all external connection points are sealed with Telewave's field-proven MilleniumSealTM, which provides permanent environmental protection. The RF feed cable and connection to each element is internally sealed within the element, eliminating any possibility of failure due to corrosion or ice expansion. The standard connector type is N-Male, and 7-16 DIN can be installed as an option for high power applications. Gain ranges from 1 to 12 dBd, depending on configuration and number of elements. Each lowband model from 33-48 MHz includes a heavy-duty clamp set to attach the antenna boom to a mast or tower, as well as one element support boom with all required clamps. All dipoles above 54 MHz are UPS shippable, and the horizontal pattern on all models is fully adjustable at any time during or after installation. This unique flexibility means that a single or multi-dipole array can provide a semi-directional, bi-directional, or nearly omni radiation pattern. Up to 15 degrees of mechanical and/or electrical tilt is also available for arrays of 2 or more dipoles, allowing a level of pattern control not possible with other antenna types. 234 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7080 Rev. 10/13 DIPOLES ANT37D DIPOLE ANTENNA The Telewave ANT37D is a rugged, Each antenna is also completely high-performance single dipole sealed with our high-tech TxylanTM antenna designed for VHF lowband coating, which resists water and ice services, including public safety, buildup, and provides exceptional utilities, paging links and military protection from corrosive gases, communication. This antenna UV radiation, salt spray, acid rain provides 7.5 MHz bandwidth and windblown abrasives. with no tuning required, and multiple elements can be stacked for increased gain and pattern control. ANT37D antennas include ANTC482 mounting hardware which will accommodate a 1.5"-3.5" diameter galvanized steel support Each antenna is constructed with pipe or tower leg. One ANTLBB 6061-T6 aluminum, and is welded element support boom with all at the base to a solid, machined required clamps is also included. aluminum mounting block for maximum strength. A massive 3.5" diameter boom provides exceptional strength. Due to the size and potential wind loading of this antenna, tower side mounting is recommended. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 33.5 - 41 MHz 7 SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain Vertical beamwidth Horizontal beamwidth Dipole dimensions (H x W) Boom dimensions (L x Dia.) Weight (antenna + clamps) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 33.5-41 MHz 500 watts 50 ohms 1.5:1 or less Offset circular DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 2.5 dBd (typ.) 78° 170° (typ.) 145 x 9 in. 96 x 3.5 in. 51 lb. 125 / 100 MPH 3.8 ft.² 152 lb Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT37D at 40 MHz 0 330 2.6 dBd 30 -3 300 -10 -20 270 60 90 240 120 210 150 180 H-Plane gain 2.6 dBd 1/4 wl. spacing from tower All specifications subject to change without notice TWDS-7073 Rev. 10/13 235 37.5 - 44.5 MHz ANT40D DIPOLE ANTENNA The Telewave ANT40D is a rugged, Each antenna is also completely high-performance single dipole sealed with our high-tech TxylanTM antenna designed for VHF lowband coating, which resists water and ice services, including public safety, buildup, and provides exceptional utilities, paging links or military protection from corrosive gases, communication. This antenna UV radiation, salt spray, acid rain provides 7 MHz bandwidth with and windblown abrasives. no tuning required, and multiple elements can be stacked for increased gain and pattern control. ANT40 D antenna s include ANTC482 mounting hardware which will accommodate a 1.5"-3.5" diameter galvanized steel support Each antenna is constructed with pipe or tower leg. One ANTLBB 6061-T6 aluminum, and is welded element support boom with all at the base to a solid, machined required clamps is also included. aluminum mounting block for maximum strength. A massive 3.5" diameter boom provides exceptional strength. Due to the size and potential wind loading of this antenna, tower side mounting is recommended. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain (typ.) Vertical beamwidth Horizontal beamwidth Dipole dimensions (H x W) Boom dimensions (L x Dia.) Weight (antenna + clamps) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 37.5-44.5 MHz 500 watts 50 ohms 1.5:1 or less Offset circular DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 2.5 dBd 78° Dependent on pattern 129 x 9 in. 96 x 3.5 in. 46 lb. 125 / 100 MPH 3.6 ft.² 142 lb ANT40D at 40 MHz 0 330 2.6 dBd 30 -3 300 -10 -20 270 60 90 240 120 210 150 180 H-Plane gain 2.6 dBd 1/4 wl. spacing from tower 236 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7097 Rev. 10/13 DIPOLES ANT42D DIPOLE ANTENNA The Telewave ANT42D is a rugged, Each antenna is also completely high-performance single dipole sealed with our high-tech TxylanTM antenna designed for VHF lowband coating, which resists water and ice services, including public safety, buildup, and provides exceptional utilities, paging links or military protection from corrosive gases, communication. This antenna UV radiation, salt spray, acid rain provides 8.5 MHz bandwidth and windblown abrasives. with no tuning required, and multiple elements can be stacked for increased gain and pattern control. ANT42D antenna s include ANTC482 mounting hardware which will accommodate a 1.5"-3.5" diameter galvanized steel support Each antenna is constructed with pipe or tower leg. One ANTLBB 6061-T6 aluminum, and is welded element support boom with all at the base to a solid, machined required clamps is also included. aluminum mounting block for maximum strength. A massive 3.5" diameter boom provides exceptional strength. Due to the size and potential wind loading of this antenna, tower side mounting is recommended. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 38.5 - 47 MHz 7 SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain (typ.) Vertical beamwidth Horizontal beamwidth Dipole dimensions (H x W) Boom dimensions (L x Dia.) Weight (antenna + clamps) Dipole spacing from tower Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 38.5-47 MHz 500 watts 50 ohms 1.5:1 or less Offset circular DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 2.5 dBd 78 degrees 180 degrees 126 x 9 in. 78 x 3.5 in. 41 lb. 69 in. 125 / 100 MPH 3.3 ft.² 132 lb Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT42D at 42 MHz 0 330 2.6 dBd 30 -3 300 -10 -20 270 60 90 240 120 210 150 180 H-Plane gain 2.6 dBd 1/4 wl. spacing from tower - 69" All specifications subject to change without notice TWDS-7091 Rev. 10/13 237 ANT44D DIPOLE ANTENNA The Telewave ANT44D is a rugged, Each antenna is also completely high-performance single dipole sealed with our high-tech TxylanTM antenna designed for VHF lowband coating, which resists water and ice services, including public safety, buildup, and provides exceptional utilities, paging links or military protection from corrosive gases, communication. This antenna UV radiation, salt spray, acid rain provides 6.5 MHz bandwidth and windblown abrasives. with no tuning required, and multiple elements can be stacked for increased gain and pattern control. ANT44D antenna s include ANTC482 mounting hardware which will accommodate a 1.5"-3.5" diameter galvanized steel support Each antenna is constructed with pipe or tower leg. One ANTLBB 6061-T6 aluminum, and is welded element support boom with all at the base to a solid, machined required clamps is also included. aluminum mounting block for maximum strength. A massive 3.5" diameter boom provides exceptional strength. Due to the size and potential wind loading of this antenna, tower side mounting is recommended. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY 41.5 - 48 MHz SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain (typ.) Vertical beamwidth Horizontal beamwidth Dipole dimensions (H x W) Boom dimensions (L x Dia.) Weight (antenna + clamps) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 41.5-48 MHz 500 watts 50 ohms 1.5:1 or less Offset circular DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 2.5 dBd 78 degrees Dependent on pattern 120 x 9 in. 78 x 3.5 in. 41 lb. 125 / 100 MPH 3.2 ft.² 129 lb ANT44D at 44 MHz 0 330 2.6 dBd 30 -3 300 -10 -20 270 60 90 240 120 210 150 180 H-Plane gain 2.6 dBd 1/4 wl. spacing from tower 238 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7107 Rev. 10/13 ANT50D DIPOLE ANTENNA 45 - 54 MHz 7 DIPOLES The Telewave ANT50D is a rugged, Each antenna is also completely high-performance single dipole sealed with our high-tech TxylanTM antenna designed for VHF lowband coating, which resists water and ice services, including public safety, buildup, and provides exceptional utilities, military communication, protection from corrosive gases, and amateur radio. This antenna UV radiation, salt spray, acid rain provides 9 MHz bandwidth with and windblown abrasives. no tuning required. The horizontal pattern is adjustable, and multiple elements can be stacked for increased gain and pattern control. ANT50D antennas include ANTC482 mounting hardware which will accommodate a 1.5"-3.5" diameter galvanized steel support pipe or tower leg. Due to the size Each antenna is constructed with and potential wind loading of this 6061-T6 aluminum, and is welded antenna, tower side mounting is at the base to a solid, machined recommended. aluminum mounting block for maximum strength. A massive 3.5" diameter boom provides exceptional strength. NOTE: THIS ANTENNA IS SHIPPED VIA TRUCK FREIGHT ONLY SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain (dependent on pattern) Vertical beamwidth Horizontal beamwidth Dipole dimensions (H x W) Boom dimensions (L x Dia.) Weight (antenna + clamps) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 45-54 MHz 500 watts 50 ohms 1.5:1 or less Adjustable: offset circular or cardioid DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 1-2.5 dBd 78° Dependent on pattern 108 x 9 in. 96 x 3.5 in. 53 lb. 125 / 100 MPH 3.2 ft.² 129 lb Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 330 300 270 0 2.6 dBd -3 -10 -20 30 60 90 240 120 210 150 180 H-Plane gain 2.6 dBd 1/4 wl. spacing from tower ANT50D at 49 MHz 0 330 30 0.7 dBd -3 300 -10 2.2 dBd -20 60 2.2 dBd 270 90 240 120 -3.5 dBd 210 150 180 H-Plane gain 0.7 dBd 3/8 wl. spacing from tower All specifications subject to change without notice TWDS-7067 Rev. 10/13 239 ANT70D DIPOLE ANTENNA The Telewave ANT70D is a rugged, Each antenna is also completely high-performance single dipole sealed with our high-tech TxylanTM antenna designed for VHF midband coating, which resists water and ice services, including utilities, paging buildup, and provides exceptional links, control stations, and military protection from corrosive gases, communication. This antenna UV radiation, salt spray, acid rain provides 15 MHz bandwidth with and windblown abrasives. no tuning required. The horizontal pattern is adjustable, and multiple elements can be stacked for increased gain and pattern control. All components are at DC ground potential for lightning protection. A full clamp set is included for mounting to a 1.5"-3.5" diameter galvanized steel support pipe or Each antenna is constructed with tower leg. 6061-T6 aluminum, and is welded at the base for maximum strength. 63 - 78 MHz SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain (dependent on pattern) Vertical beamwidth Horizontal beamwidth Dipole dimensions (H x W) Boom dimensions (L x Dia.) Weight (antenna + clamps) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 63-78 MHz 500 watts 50 ohms 1.5:1 or less Adjustable for offset circular, cardioid, or bidirectional DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 1-2.5 dBd 78° Dependent on pattern 76 x 7 in. 84 x 2.25 in. 21 lb. 125 / 100 MPH 2.7 ft.² 109 lb 240 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 330 300 270 0 2.6 dBd -3 -10 -20 30 60 90 240 120 210 150 180 H-Plane gain 2.6 dBd 1/4 wl. spacing from tower ANT70D at 70 MHz 330 300 2.2 dBd 270 0 0.7 dBd -3 -10 -20 30 60 2.2 dBd 90 240 -3.5 dBd 120 210 150 180 H-Plane gain 0.7 dBd 3/8 wl. spacing from tower All specifications subject to change without notice TWDS-7098 Rev. 3/12 DIPOLES ANT75D DIPOLE ANTENNA The Telewave ANT75D is a rugged, Each antenna is also completely high-performance single dipole sealed with our high-tech TxylanTM antenna designed for VHF midband coating, which resists water and ice services, including utilities, paging buildup, and provides exceptional links, control stations, and military protection from corrosive gases, communication. This antenna UV radiation, salt spray, acid rain provides 22 MHz bandwidth with and windblown abrasives. no tuning required. The horizontal pattern is adjustable, and multiple elements can be stacked for increased gain and pattern control. All components are at DC ground potential for lightning protection. A full clamp set is included for mounting to a 1.5"-3.5" diameter galvanized steel support pipe or Each antenna is constructed with tower leg. 6061-T6 aluminum, and is welded at the base for maximum strength. 66 - 88 MHz 7 SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain (dependent on pattern) Vertical beamwidth Horizontal beamwidth Dipole dimensions (H x W) Boom dimensions (L x Dia.) Weight (antenna + clamps) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 66-88 MHz 500 watts 50 ohms 1.5:1 or less Adjustable: Offset circular, cardioid, or bidirectional DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 1-2.5 dBd 78° Dependent on pattern 72 x 7 in. 65 x 2.25 in. 21 lb. 125 / 100 MPH 2.3 ft.² 92 lb Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 0 330 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 H-Plane gain 2.6 dBd 1/4 wl. spacing from tower ANT75D at 75 MHz 0 330 30 -3 300 -10 -20 270 60 90 240 120 210 150 180 H-Plane gain 0.7 dBd 3/8 wl. spacing from tower All specifications subject to change without notice TWDS-7076 Rev. 8/12 241 ANT90D DIPOLE ANTENNA - FM BROADCAST The Telewave ANT90D is a rugged, buildup, and provides exceptional high-performance single dipole protection from corrosive gases, antenna designed for the FM UV radiation, salt spray, acid rain broadcast band. This antenna and windblown abrasives. provides 20 MHz bandwidth with no tuning required. The horizontal pattern is adjustable, and multiple elements can be stacked for increased gain and pattern control. This antenna is ideal for LPFM and translator stations for fill-in or small- All components are at DC ground potential for lightning protection. A full clamp set is included for mounting to a 1.5"-3.5" diameter galvanized steel support pipe or tower leg. market coverage. Up to 15 degrees of electrical uptilt Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each element is also completely sealed with our high-tech TxylanTM coating, which resists water and ice or downtilt can be specified for multiple element arrays. Desired tilt angle must be included with the order, and consultation with our antenna engineering staff is requested. 88 - 108 MHz 0 330 30 -3 SPECIFICATIONS Frequency (continuous) Power rating (typ.) Impedance VSWR Pattern Lightning protection Termination Gain (dependent on pattern) Vertical beamwidth Horizontal beamwidth Dimensions (H x mast distance) max Weight (antenna + clamps) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH 88-108 MHz 500 watts 50 ohms 1.5:1 or less Adjustable: Offset circular, cardioid, or bidirectional DC Ground N-Male or 7-16 DIN (opt.) on harness feed cable 1 - 2.05 dBd 1/4 wl. - 70°, 1/2 wl. - 73° 3/8 wl. - 84° 1/4 wl. - 210°, 1/2 wl. - 88° 3/8 wl. - 240° 56 x 57 in. 18 lb. 125 / 100 MPH 1.9 ft.² 74 lb. 300 -10 -20 270 60 90 240 120 210 150 180 H-Plane, Gain = 2.1 dBd Spaced 1/4 wl. from mast ANT90D at 98 MHz 0 330 30 -3 300 -10 -20 270 60 90 240 120 210 150 180 H-Plane, Gain = 1.9 dBd Spaced 3/8 wl. from mast 242 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7028 Rev. 11/08 ANT120D, D3 DIPOLE AND DIPOLE ARRAY 110 - 138 MHz 7 DIPOLES The Telewave ANT120D series radiation, salt spray, acid rain and con s i s t s of a r u g g e d, hig h - windblown abrasives. The phasing performance single dipole and harness is fully sealed by Telewave's dual dipole array with a precision Millenium SealTM technology. phasing harness, designed for aircraft communications, telemetry, and military applications. The horizontal pattern is adjustable, and each element can be configured for increased gain and pattern control. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each element is also completely sealed with our high-tech TxylanTM coating, which resists water and ice buildup, and provides exceptional Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 models. Desired tilt angle must be included with the order, and consultation with our antenna engineering staff is requested. protection from corrosive gases, UV ANT120D COMMON SPECIFICATIONS Frequency (continuous) 110-138 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating (D/D3) 150/125 MPH Impedance 50 ohms (with 0.5" ice) (D/D3) 125/100 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT120D ANT120D3 Gain (dependent on pattern) 1-2.5 dBd 3-5.6 dBd Vertical beamwidth (3/8 wl.) 78° 34° Dimensions (H x D) max 45 x 45 in. 119 x 45 in. Weight (antenna + clamps) 7 lb. 15 lb. Maximum exposed area 0.91 ft.² 1.9 ft.² Lateral thrust at 100 MPH 36 lb. 75 lb. Electrical uptilt / downtilt N/A 1-15° ANT120D3 (Harness not shown) Support mast is customer-supplied 0 330 -3 300 -10 -20 270 ANT120D 0 30 330 -3 60 300 -10 -20 90 270 30 60 90 0 330 -3 300 -10 -20 270 ANT120D3 0 30 330 -3 60 300 -10 -20 90 270 30 60 90 240 120 210 150 180 H-Plane gain 2.4 dBd Spaced 1/4 wl. from mast 240 120 210 150 180 H-Plane gain 1.9 dBd Spaced 3/8 wl. from mast 240 120 210 150 180 H-Plane gain 6.0 dBd Spaced 1/4 wl. from mast Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 240 120 210 150 180 H-Plane gain 5.6 dBd Spaced 3/8 wl. from mast All specifications subject to change without notice TWDS-7060 Rev. 6/12 243 138 - 174 MHz ANT150D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd The Telewave ANT150D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing f o r o p t i m u m p e r f o r m a n c e . harness is fully sealed by Telewave's The horizontal pattern is field- Millenium SealTM technology. adjustable for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for applications including trunking, business, public safety, and amateur radio. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each element is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included with the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane: Gain 9.1 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane: Gain 9.1 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane: Gain 8.5 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 138-174 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL ANT150D ANT150D3 ANT150D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 78° 37° 18° Dimensions (H x D) max 34 x 33 in. 89 x 33 in. 195 x 33 in. Weight (antenna + clamps) 6 lb. 14 lb. 28 lb. Maximum exposed area 0.73 ft.² 1.6 ft.² 3.3 ft.² Lateral thrust at 100 MPH 29 lbs 64 lbs 134 lbs Electrical uptilt or downtilt N/A 1-15° 1-15° 244 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT150D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7045 Rev. 4/12 ANT150D7-12 DIPOLE ARRAY 7 TO 12 dBd 138 - 174 MHz 7 DIPOLES The Telewave ANT150D7-12 is an sealed with our high-tech TxylanTM 8-element dipole array antenna coating, which resists water and ice with a precision phasing harness buildup, and provides exceptional for optimum performance. The protection from corrosive gases, UV horizontal pattern is field-adjustable, radiation, salt spray, acid rain and to accommodate any current or windblown abrasives. The phasing future coverage requirements. The harness is fully sealed by Telewave's high gain, wide bandwidth, and Millenium SealTM technology. high efficiency of the ANT150D7-12 are ideal for many applications, including trunking, business, public safety, and amateur radio. All components are at DC ground for lightning protection, and each element includes a heavy-duty custom clamp set for mounting to a Each antenna consists of t wo 1.5"-2.5" diameter galvanized steel arrays of 4 elements with a power support pipe or tower leg. divider in the center, which greatly reduces feedline losses. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely 0 330 -3 300 -10 -20 270 30 60 90 330 300 270 0 -3 -10 -20 30 60 90 330 300 270 0 -3 -10 -20 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 12.2 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 11.8 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 12.7 dBd 3/8 wl. spacing from tower SPECIFICATIONS Frequency (continuous) 138-174 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Female or 7-16 DIN (opt.) on power divider Gain (dependent on pattern) 7-12 dBd Vertical beamwidth (3/8 wl.) 8° Dimensions (H x D) max 407 x 36 in. (1/2 wl. spacing) Weight (antenna + clamps) 60 lb. Maximum exposed area 6.8 ft.² Lateral thrust at 100 MPH 282 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT150D7-12 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7070 Rev. 2/09 245 216 - 252 MHz ANT220D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd The Telewave ANT220D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including wireless PTC, trunking, business, public safety, and amateur radio. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane: Gain 9.1 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane: Gain 9.1 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane: Gain 8.5 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 216-252 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT220D ANT220D3 ANT220D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 spacing ) 78° 37° 18° Dimensions (H x D) max 23 x 28 in. 61 x 28 in. 137 x 28 in. Weight (antenna + clamps) 5 lb. 11 lb. 23 lb. Maximum exposed area 0.51 ft.² 1.1 ft.² 2.3 ft.² Lateral thrust at 100 MPH 20 lb. 43 lb. 94 lb. Electrical uptilt / downtilt N/A 1-15° 1-15° 246 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT220D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7044 Rev. 7/11 ANT275D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd 230 - 330 MHz 7 DIPOLES The Telewave ANT275D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including military communications, trunking, and business. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.1 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 9.0 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 8.8 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 230-330 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT275D ANT275D3 ANT275D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 78° 34° 15° Dimensions (H x D) (max) 19 x 20 in. 56 x 20 in. 120 x 20 in. Weight (antenna + clamps) 6 lb. 11 lb. 19 lb. Maximum exposed area 0.45 ft.² 1.0 ft.² 2.1 ft.² Lateral thrust at 100 MPH 18 lb. 39 lb. 83 lb. Electrical uptilt / downtilt N/A 1-15° 1-15° Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT275D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7079 Rev. 5/11 247 300 - 360 MHz ANT350D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd The Telewave ANT350D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including military communications, trunking, and business. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.1 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 9.1 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 8.5 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 300-360 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT350D ANT350D3 ANT350D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 71° 34° 15° Dimensions (H x D) (max) 17 x 17 in. 43 x 17 in. 89 x 17 in. Weight (antenna + clamps) 6 lb. 13 lb. 18 lb. Maximum exposed area 0.36 ft.² 0.78 ft.² 1.7 ft.² Lateral thrust at 100 MPH 15 lb. 34 lb. 73 lb. Electrical uptilt / downtilt N/A 1-15° 1-15° 248 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT350D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7040 Rev. 5/09 ANT375D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd 345 - 405 MHz 7 DIPOLES The Telewave ANT375D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including military communications, TETRA, and business. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.17 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 9.1 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 8.5 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 345-405 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT375D ANT375D3 ANT375D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 71° 34° 15° Dimensions (H x D) (max) 16 x 17 in. 39 x 17 in. 87 x 17 in. Weight (antenna + clamps) 7 lb. 15 lb. 25 lb. Maximum exposed area 0.35 ft.² 0.76 ft.² 1.7 ft.² Lateral thrust at 100 MPH 14 lb. 32 lb. 70 lb. Electrical uptilt / downtilt N/A 1-15° 1-15° Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT375D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7071 Rev. 5/09 249 360 - 450 MHz ANT400D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd The Telewave ANT400D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including military communications, TETRA trunking, and amateur radio. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.07 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 9.10 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 8.46 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 360-450 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT400D ANT400D3 ANT400D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 71° 34° 15° Dimensions (H x D) (max) 15 x 14 in. 36 x 14 in. 74 x 14 in. Weight (antenna + clamps) 6 lbs 13 lbs 18 lbs Maximum exposed area 0.34 ft.² 0.72 ft.² 1.5 ft.² Lateral thrust at 100 MPH 13 lbs 30 lbs 64 lbs Electrical uptilt / downtilt N/A 1-15° 1-15° 250 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT400D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7048 Rev. 5/09 ANT425D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd 380 - 470 MHz 7 DIPOLES The Telewave ANT425D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including military communications, trunking, public safety, and amateur radio. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 330 300 270 0 -3 -10 -20 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.02 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 9.08 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 9.12 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 380-470 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT425D ANT425D3 ANT425D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 71° 34° 15° Dimensions (H x D) (max) 13 x 17 in. 34 x 17 in. 77 x 17 in. Weight (antenna + clamps) 7 lbs 15 lbs 32 lbs Maximum exposed area 0.34 ft.² 0.72 ft.² 1.5 ft.² Lateral thrust at 100 MPH 13 lbs 30 lbs 64 lbs Electrical uptilt / downtilt N/A 1-15° 1-15° Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT425D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7105 Rev. 5/12 251 406 - 512 MHz ANT450D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd The Telewave ANT450D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including trunking, business, public safety, government, and amateur radio. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.1 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 9.1 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 8.5 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 406-512 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT450D ANT450D3 ANT450D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 71° 34° 15° Dimensions (H x D) (max) 13 x 12 in. 31 x 12 in. 71 x 12 in. Weight (antenna + clamps) 6 lbs 13 lbs 18 lbs Maximum exposed area 0.27 ft.² 0.68 ft.² 1.4 ft.² Lateral thrust at 100 MPH 11 lbs 28 lbs 60 lbs Electrical uptilt / downtilt N/A 1-15° 1-15° 252 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT450D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7033 Rev. 5/09 ANT450D7-12 DIPOLE ARRAY 7 TO 12 dBd 406 - 512 MHz 7 DIPOLES The Telewave ANT450D7-12 is an sealed with our high-tech TxylanTM 8-element dipole array antenna coating, which resists water and ice with a precision phasing harness buildup, and provides exceptional for optimum performance. The protection from corrosive gases, UV horizontal pattern is field-adjustable, radiation, salt spray, acid rain and to accommodate any current or windblown abrasives. The phasing future coverage requirements. The harness is fully sealed by Telewave's high gain, wide bandwidth, and Millenium SealTM technology. high efficiency of the ANT450D7-12 are ideal for many applications, including trunking, business, public safety, and amateur radio. All components are at DC ground for lightning protection, and each element includes a heavy-duty custom clamp set for mounting to a Each antenna consists of t wo 1.5"-2.5" diameter galvanized steel arrays of 4 elements with a power support pipe or tower leg. divider in the center, which greatly reduces feedline losses. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 12.2 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 11.8 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 12.7 dBd 3/8 wl. spacing from tower SPECIFICATIONS Frequency (continuous) 406-512 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Female or 7-16 DIN (opt.) on power divider Gain (dependent on pattern) 7-12 dBd Vertical beamwidth (3/8 wl.) 7.5° Dimensions (H x D) max 148 x 12 in. (1/2 wl. spacing) Weight (antenna + clamps) 36 lb. Maximum exposed area 2.9 ft.² Lateral thrust at 100 MPH 135 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT450D7-12 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7034 Rev. 2/09 253 470 - 550 MHz ANT500D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd The Telewave ANT550D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including trunking, business, public safety, and government communication. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.1 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 9.1 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 8.5 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 470-550 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 175 MPH Impedance 50 ohms (with 0.5" ice) 150 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT500D ANT500D3 ANT500D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 78° 33° 18° Dimensions (H x D) (max) 13 x 11 in. 31 x 11 in. 65 x 11 in. Weight (antenna + clamps) 7 lb. 14 lb. 28 lb. Maximum exposed area 0.26 ft.² 0.56 ft.² 1.2 ft.² Lateral thrust at 100 MPH 10 lb. 22 lb. 50 lb. 254 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT500D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7025 Rev. 11/08 ANT750D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd 700 - 825 MHz 7 DIPOLES The Telewave ANT750D series buildup, and provides exceptional consist s of single, dual, and protection from corrosive gases, UV 4-element dipole array antennas radiation, salt spray, acid rain and with a precision phasing harness windblown abrasives. The phasing for optimum performance. The harness is fully sealed by Telewave's antenna horizontal pattern is field- Millenium SealTM technology. adjustable, for any current or future coverage requirements. The wide bandwidth and high efficiency of these antennas make them ideal for many applications, including trunking, business, public safety, and goverment communication. All components are at DC ground potential for lightning protection. Each dipole element includes a heavy-duty custom clamp set for mounting to a 1.5"-2.5" diameter galvanized steel support pipe or tower leg. Each dipole element is constructed with 6061-T6 aluminum, and welded at the base for maximum strength. Each antenna is also completely sealed with our high-tech TxylanTM coating, which resists water and ice Up to 15 degrees of electrical uptilt or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 240 120 240 120 210 150 180 H-Plane gain 9.1 dBd 1/4 wl. spacing from tower 210 150 180 H-Plane gain 8.9 dBd 1/2 wl. spacing from tower 210 150 180 H-Plane gain 9.2 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 700-825 MHz Lightning protection DC Ground Power rating (typ.) 500 watts Wind rating 200 MPH Impedance 50 ohms (with 0.5" ice) 175 MPH VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Male or 7-16 DIN (opt.) on harness feed cable MODEL SPECIFICATIONS ANT750D ANT750D3 ANT750D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 68° 33° 18° Dimensions (H x D) (max) 8 x 7 in. 19 x 7 in. 42 x 7 in. Weight (antenna + clamps) 7 lb. 14 lb. 28 lb. Maximum exposed area 0.17 ft.² 0.42 ft.² 0.91 ft.² Lateral thrust at 100 MPH 7 lb. 17 lb. 38 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT750D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7026 Rev. 11/08 255 800 - 1000 MHz ANT900D, D3, D6-9 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd The Telewave ANT900D series Each antenna is also completely consist s of single, dual, and sealed with our high-tech TxylanTM 4-element dipole array antennas coating, which resists water and ice with a precision phasing harness buildup, and provides exceptional for optimum performance. The protection from corrosive gases, antenna horizontal pattern is UV radiation, salt spray, acid rain field-adjustable, for any current and windblown abrasives. or future coverage requirements. The exceptionally wide bandwidth and high efficiency of these antennas make them ideal for many applications, including trunking, Each element includes a heavy-duty custom clamp set for mounting to a 0.5"-1.5" diameter galvanized steel support pipe or tower leg. cellular, data, and paging. Up to 15 degrees of electrical uptilt Each dipole element is constructed with 6061-T6 aluminum, fully welded to prevent intermodulation. The 2 and 4 element arrays utilize a power divider for minimum loss. or downtilt may be specified for D3 or D6-9 models. Desired tilt angle must be included on the order, and consultation with our antenna engineering staff is requested. 330 300 270 0 -3 -10 -20 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 H-Plane gain 9.27 dBd 1/4 wl. spacing from tower 240 120 210 150 180 H-Plane gain 8.7 dBd 1/2 wl. spacing from tower 240 120 210 150 180 H-Plane gain 9.1 dBd 3/8 wl. spacing from tower COMMON SPECIFICATIONS Frequency (continuous) 800-1000 MHz Wind rating 200 MPH Power rating (typ.) 500 watts (with 0.5" ice) 175 MPH Impedance 50 ohms VSWR 1.5:1 or less Pattern Adjustable: Offset circular, cardioid, or bidirectional Termination N-Female or 7-16 DIN (opt.) on power divider MODEL SPECIFICATIONS ANT900D ANT900D3 ANT900D6-9 Gain (dependent on pattern) 1-2.5 dBd 3-6 dBd 6-9 dBd Vertical beamwidth (3/8 wl.) 84° 35° 17° Dimensions (H x D) (max) 8 x 6 in. 21 x 6 in. 49 x 6 in. Weight (antenna + clamps) 3 lb. 7 lb. 11 lb. Maximum exposed area 0.1 ft.² 0.2 ft.² 0.4 ft.² Lateral thrust at 100 MPH 4 lb. 9 lb. 20 lb. 256 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANT900D6-9 (Harness not shown) Support mast is customer-supplied All specifications subject to change without notice TWDS-7019 Rev. 11/08 DIPOLES FOLDED DIPOLE ANTENNAS 138-825 MHz 7 MOUNTING INSTRUCTIONS WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. PARTS LIST (for single dipole element): (1) Dipole and clamp set (2) 3/8" x 3.5" hex bolt (1) Anti-seize compound (1) 1/4"-20 hex bolt (2) 3/8" hex nut (1) 1/4"-20 lock nut (2) 3/8" split lock washer ASSEMBLY INSTRUCTIONS 1. Remove components from shipping box and lay out the dipole and cable assemblies, ideally in a large, sheltered area. Arrange the assemblies in order as cable lengths allow. 2. Refer to the diagram. Slide the boom over the dipole hub, and align the holes in the boom with the holes in the hub. Apply anti-seize compound to the bolt end, then install and tighten the 1/4"-20 bolt and lock nut. Press the end plug located on the dipole feed cable into the end of the boom until it is firmly seated. 3. Refer to the appropriate Dipole Pattern Adjustment sheet for the frequency range of the antenna. Using the chart titled "Dipole Mounting and Mast Specifications", measure and mark the support structure for the proper dipole element spacing. Mount each dipole assembly to the mast with clamps as shown in the diagram. Locate the drain hole on each element, and be certain it is pointing down. 4. Refer to the chart titled "Mast to Dipole Dimensions", and determine the proper horizontal element spacing from the mast or support structure for the desired coverage pattern. At least 1/2 inch of the boom should be visible on the back side of the clamps. 5. Apply anti-seize compound to the bolt ends, then secure the dipole assemblies to the support with the supplied 3/8" nuts, washers and bolts, while adjusting each dipole position on the support. Tighten each nut until the lock washer is flat, then add 1/2 turn. Be sure to properly seal the input connector with waterproof tape or other sealing material. See Telewave TWDS-0502 for a recommended method of connector sealing. 6. Secure the cable assembly to the support. 1/2 inch of the boom visible Dipole Element Clamp Assemblies Boom Dipole Hub 1/4"-20 Bolt / Nut Phasing Harness Drain Holes End Plug Coax Drain Hole Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7089 Rev. 3/11 257 DIPOLE PATTERN ADJUSTMENT 30 - 300 MHz Telewave folded dipoles are field adjustable to provide different horizontal patterns and gain values. The horizontal spacing from tower between the dipole and the support mast or tower leg controls this adjustment. Review the patterns below to determine which is best suited to your range area requirements. Use the chart on the next page to find the appropriate dimension for antenna to mast spacing. The drawing at the bottom shows how this measurement is made and the vertical spacing to be used for multi-element arrays. 0 330 -3 300 -10 -20 270 Horizontal radiation patterns 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 Offset Circular 1/4 wavelength spacing 240 120 210 150 180 Cardioid 3/8 wavelength spacing 0 330 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 Bi-directional 1/2 wavelength spacing Mast Extension Horizontal Spacing Measured distance from the face of the mast to the middle of the dipole loop. Vertical spacing Mast Extension Drain Holes IMPORTANT: Be sure that the drain holes are on the bottom when the elements are installed. 258 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7057 Rev. 6/12 DIPOLE PATTERN ADJUSTMENT 30 - 300 MHz 7 DIPOLES DIPOLE MOUNTING AND MAST SPECIFICATIONS Mast lengths shown are minimum acceptable lengths to insure proper pattern control. Mast extension is applied at top and bottom of array. Longer masts are acceptable, but the dipole or array must be centered on the support to prevent beam tilt. The clamps provided with the dipoles will work properly to attach the dipole boom to a mast that is between 1.5 to 2.5 inches in diameter. To attach to smaller supports (1-1.5" diameter), use ANTS420 shims. This allows direct mounting to small towers such as the Rohn 25 and 45. MAST MINIMUM LENGTH AND ELEMENT VERTICAL SPACING (at midband) ANTENNA MAST LENGTH MAST EXTENSION VERTICAL SPACING MINIMUM MAST TYPE ANT37D ANT40D ANT50D ANT70D ANT75D ANT75D3 ANT90D ANT90D3 ANT120D ANT120D3 ANT120D6-9 ANT150D ANT150D3 ANT150D6-9 ANT150D7-12 ANT220D ANT220D3 ANT220D6-9 ANT275D ANT275D3 ANT275D6-9 6'-7" 6'-7" 16'-1" 5'-6" 12'-11" 4'-2" 10' 21' 3' 7'-5" 16'-3" 33'-11" 2'-4" 5'-6" 11'-8" 2' 4'-8" 10' CONTACT TELEWAVE FOR MOUNTING ADVICE 3'-3.5" 3'-3.5" 3'-3.5" 2'-9" 2'-9" 2'-1" 23" 23" 18" 18" 18" 18" 14" 14" 14" 12" 12" 12" N/A N/A 9'-7" N/A 7'-5" N/A 6'-2" 6'-2" N/A 4'-5" 4'-5" 4'-5" N/A 3'-1.5" 3'-1.5" N/A 2'-8" 2'-8" 2.0" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 2.0" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe 1.5" Schedule 40 Galvanized Pipe ELEMENT HORIZONTAL SPACING FROM TOWER (at midband) MODEL 1/4 wl. OFFSET CIRCULAR 3/8 wl. CARDIOID 1/2 wl. BI-DIRECTIONAL ANT37D 6'-3" N/A N/A ANT40D 5'-9" N/A N/A ANT50D 4'-7" 6'-11" N/A ANT70D ANT75D, D3 ANT90D, D3 ANT120D, D3, D6-9 3'-3" 3' 2'-4" 22" 5' 4'-6" 3'-6" 2'-9" MAX EXTENSION MAX EXTENSION 4'-9" 3'-9" ANT150D, D3, D6-9, D7-12 18" 2'-3" 2' 9" ANT220D, D3, D6-9 12" 18" 2' ANT275D, D3, D6-9 10" 15" 20" NOTE: The physical characteristics of large dipoles require a correction factor from calculated values for mast spacing. The dimensions in the above table include this correction. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7057 Rev. 6/12 259 DIPOLE PATTERN ADJUSTMENT 300 - 1000 MHz Telewave folded dipoles are field adjustable to provide different horizontal patterns and gain values. The horizontal spacing from tower between the dipole and the support mast or tower leg controls this adjustment. Review the patterns below to determine which is best suited to your range area requirements. Use the chart on the next page to find the appropriate dimension for antenna to mast spacing. The drawing at the bottom shows how this measurement is made and the vertical spacing to be used for multi-element arrays. 0 330 -3 300 -10 -20 270 Horizontal radiation patterns 30 60 90 0 330 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 Offset Circular 1/4 wavelength spacing 240 120 210 150 180 Cardioid 3/8 wavelength spacing 0 330 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 Bi-directional 1/2 wavelength spacing Mast Extension Horizontal Spacing Measured distance from the face of the mast to the middle of the dipole loop. Vertical spacing Mast Extension Drain Holes IMPORTANT: Be sure that the drain holes are on the bottom when the elements are installed. 260 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7058 Rev. 6/12 DIPOLE PATTERN ADJUSTMENT 300 - 1000 MHz 7 DIPOLES DIPOLE MOUNTING AND MAST SPECIFICATIONS Mast lengths shown are minimum acceptable lengths to insure proper pattern control. Mast extension is applied at top and bottom of array. Longer masts are acceptable, but the dipole or array must be centered on the support to prevent beam tilt. The clamps provided with the dipoles will work properly to attach the dipole boom to a mast that is between 1.5 to 2.5 inches in diameter. To attach to smaller supports (1-1.5" diameter), use ANTS420 shims. This allows direct mounting to small towers such as the Rohn 25 and 45. MAST MINIMUM LENGTH AND ELEMENT VERTICAL SPACING (at midband) ANTENNA MAST LENGTH MAST EXTENSION VERTICAL SPACING MINIMUM MAST TYPE ANT350D 20" 10" N/A 1.5" Schedule 40 Galvanized Pipe ANT350D3 3'-7" 10" 23" 1.5" Schedule 40 Galvanized Pipe ANT350D6-9 7'-5" 10" 23" 1.5" Schedule 40 Galvanized Pipe ANT375D 16" 8" N/A 1.5" Schedule 40 Galvanized Pipe ANT375D3 3'-3" 8" 24" 1.5" Schedule 40 Galvanized Pipe ANT375D6-9 7'-3" 8" 24" 1.5" Schedule 40 Galvanized Pipe ANT400D 15" 7.5" N/A 1.5" Schedule 40 Galvanized Pipe ANT400D3 3' 7.5" 22" 1.5" Schedule 40 Galvanized Pipe ANT400D6-9 6'-2" 7.5" 22" 1.5" Schedule 40 Galvanized Pipe ANT425D 14" 7" N/A 1.5" Schedule 40 Galvanized Pipe ANT425D3 2'-11" 7" 21" 1.5" Schedule 40 Galvanized Pipe ANT425D6-9 6'-5" 7" 21" 1.5" Schedule 40 Galvanized Pipe ANT450D 13" 6.5" N/A 1.5" Schedule 40 Galvanized Pipe ANT450D3 2'-7" 6.5" 19.375" 1.5" Schedule 40 Galvanized Pipe ANT450D6-9 5'-11" 6.5" 19.375" 1.5" Schedule 40 Galvanized Pipe ANT450D7-12 12'-4" 6.5" 19.375" 1.5" Schedule 40 Galvanized Pipe ANT500D 13" 6.5" N/A 1.5" Schedule 40 Galvanized Pipe ANT500D3 2'-7" 6.5" 17.5" 1.5" Schedule 40 Galvanized Pipe ANT500D6-9 5'-5" 6.5" 17.5" 1.5" Schedule 40 Galvanized Pipe ANT550D 12" 6" N/A 1.5" Schedule 40 Galvanized Pipe ANT550D3 1'-10" 5.5" 16" 1.5" Schedule 40 Galvanized Pipe ANT550D6-9 4'-6" 5.5" 16" 1.5" Schedule 40 Galvanized Pipe ANT750D 8" 4" N/A 1.5" Schedule 40 Galvanized Pipe ANT750D3 19" 4" 11.625" 1.5" Schedule 40 Galvanized Pipe ANT750D6-9 3'-6" 4" 11.625" 1.5" Schedule 40 Galvanized Pipe ANT900D 6.5" 3.25" N/A 0.5" Schedule 40 Galvanized Pipe ANT900D3 22" 4" 14" 0.5" Schedule 40 Galvanized Pipe ANT900D6-9 4'-2" 4" 14" 0.75" Schedule 40 Galvanized Pipe ELEMENT HORIZONTAL SPACING FROM TOWER (at midband) MODEL NUMBER 1/4 wl. OFFSET CIRCULAR 3/8 wl. CARDIOID ANT350D, D3, D6-9 8.4" 12.6" ANT375D, D3, D6-9 7.4" 11.1" ANT400D, D3, D6-9 6.9" 10.3" ANT425D, D3, D6-9 7" 10.5" ANT450D, D3, D6-9, D7-12 6" 9" ANT500D, D3, D6-9 5.4" 8.1" ANT550D, D3, D6-9 5" 7.5" ANT750D, D3, D6-9 3.7" 5.5" ANT900D, D3, D6-9 3.1" 4.6" Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com 1/2 wl. BI-DIRECTIONAL 16.8" 14.8" 13.7" 14" 12.1" 10.9" 10" 7.3" 6.2" All specifications subject to change without notice TWDS-7058 Rev. 6/12 261 YAGI ANTENNAS 138 - 2700 MHz Telewave Yagi antennas are some of the strongest and most reliable in the industry. These antennas are designed using sophisticated CAD and pattern modelling software, and manufactured to endure the harshest environments without failure or degradation of performance. Telewave Yagi antennas are fabricated from all-aluminum or all-brass stock, using solid elements and heavy-wall tubular booms, with fully welded or soldered joints. For the most extreme environments, certain models can be fabricated from stainless steel for ultimate durability. The RF connector is permanently mounted in end of the boom to form a single, integrated unit, except for the Y10H series, which uses a weatherproof pigtail. A solid internal conductor is sealed within the boom, and feeds a sealed active element, eliminating any possibility of failure due to corrosion or ice expansion. Telewave Yagi antennas also feature our high-tech coating called TxylanTM, which completely encapsulates all our Yagi antennas, providing total protection from water, corrosive chemicals, salt spray, and windblown abrasives. This smooth black coating also dramatically reduces surface friction, reducing and often preventing ice adhesion, while improving absorption of solar radiation. The standard connector type is N Female, and a 7-16 DIN-F can be installed as an option for higher power applications. Gain ranges from 5 to 12 dBd, and higher gains are available on request. Certain models are available with a 90degree feed option, which allows Heliax® or other hardline coax to be terminated directly at the antenna, without additional flexible jumpers. All Telewave Yagis can be ordered to accommodate vertical or horizontal polarization, and many models allow the use of our Universal Mount, which provides a high degree of adjustability for mounting antennas to non-vertical supports. Many models from 450-2700 MHz are small enough to be handheld, and are ideal for interference location and field testing. 262 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7042 Rev. 10/13 YAGIS ANT144Y5-WR YAGI ANTENNA 5 dBd 138 - 152 MHz 7 ANT144Y5-WR at 147 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 5.0 dBd -30 -60 0 330 -3 300 -10 -20 270 30 60 90 The Telewave ANT144Y5-WR is from corrosive gases, UV radiation, a high performance directional salt spray, acid rain and wind-blown antenna, designed especially for sand. The feed line is protected point to point as well as point/ within the boom, and the radiating multipoint applications. This antenna element is completely sealed produces 5 dBd forward gain with against ice and other hazards with an excellent front-to-back ratio, and a tough, RF-transparent radome. solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT144Y5-WR includes a welded vertical plate and mast clamp set. A horizontal welded Eac h antenna is completely plate is optional, or the ANTM400H protected with our high-tech adapter can be used. The clamp TxylanTM coating, which provides set fits any vertical mast or tower icing resistance and protection support from 1.5"-3.5" O.D. 240 210 H-Plane 180 Gain: 5.0 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 138-152 MHz 5 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 64° / 120° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 3 38 x 42 in. 17 lb. 20 lb. 150 / 125 MPH 1.1 ft.² 44 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7087 Rev. 10/13 263 148 - 174 MHz ANT150Y7-WR YAGI ANTENNA 5 dBd ANT150Y7-WR at 156 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 5.1 dBd -30 -60 0 330 -3 300 -10 -20 270 30 60 90 The Telewave ANT150Y7-WR is from corrosive gases, UV radiation, a high performance directional salt spray, acid rain and wind-blown antenna, designed especially for sand. The feed line is protected point to point as well as point/ within the boom, and the radiating multipoint applications. This antenna element is completely sealed produces 5 dBd forward gain with against ice and other hazards with an excellent front-to-back ratio, and a tough, RF-transparent radome. solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT150Y7-WR includes a welded vertical plate and mast clamp set. A horizontal welded Eac h antenna is completely plate is optional, or the ANTM400H protected with our high-tech adapter can be used. The clamp TxylanTM coating, which provides set fits any vertical mast or tower icing resistance and protection support from 1.5"-3.5" O.D. 240 210 H-Plane 180 Gain: 5.1 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 148-174 MHz 5 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 64° / 114° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 3 38 x 40.5 in. 16 lb. 19 lb. 150 / 125 MPH 1.0 ft.² 41 lb. 264 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7005 Rev. 10/13 YAGIS ANT150Y10H YAGI ANTENNA 10 dBd 144 - 174 MHz 7 ANT150Y10H at 156 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.1 dBd -30 -60 The Telewave ANT150Y10H is a against ice and other hazards. All very rugged, high performance antenna components are at DC directional antenna. Six elements ground for lightning protection. provide a minimum of 10 dBd gain, high front-to-back ratio, and wide band capability. The elements are constructed from solid aluminum to prevent intermodulation and provide exceptional strength. The ANT150Y10H includes a heavy duty clamp set, which allows the antenna boom to be rotated for polarization adjustment. (Please contact Telewave if horizontal operation is planned.) Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection This clamp set secures the antenna to a vertical or horizontal mast or tower support from 1.5"-3.5" O.D. The antenna is shipped from corrosive gases, UV radiation, unassembled to reduce cost, and salt spray, acid rain and wind-blown is easily assembled in the field with sand. The feed line is protected color coded marks. within the boom, and the radiating element is completely sealed 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain 10.1 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 144-174 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 17 dB 44° / 47° Directional / Vertical (Horizontal opt. if specified) N Male or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) Bending moment at mast clamp 6 96 x 40 in. 33 lb. 37 lb. 150 / 100 MPH 1.7 ft.² 67 lb. 222 ft. lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7041 Rev. 10/13 265 ANT220Y7-WR YAGI ANTENNA 5 dBd 216 - 240 MHz ANT220Y7-WR at 221 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 5.1 dBd -30 -60 0 330 30 -3 300 -10 60 -20 The Telewave ANT220Y7-WR is icing resistance and protection a high performance directional from corrosive gases, UV radiation, antenna, designed especially for salt spray, acid rain and wind-blown point to point as well as point/ sand. The feed line is protected multipoint applications. This antenna within the boom, and the radiating produces 5 dBd forward gain with element is completely sealed an excellent front-to-back ratio, against ice and other hazards with and solid aluminum elements with a tough, RF-transparent radome. 360° welds prevent intermodulation and provide exceptional strength. The ANT220Y7-WR is an excellent choice for wireless PTC systems in urban or rural areas. The ANT220Y7-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp Eac h antenna is completely set fits any vertical mast or tower protec ted with our high-tech support from 1.5"-3.5" O.D. TxylanTM coating, which provides 270 90 240 210 H-Plane 180 Gain: 5.1 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 216-240 MHz 5 dBd 500 watts 50 ohms / 1.5:1 (max) 15 dB 64° / 114° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 3 30 x 30 in. 13 lb. 16 lb. 150 / 125 MPH 0.7 ft.² 28 lb. 266 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7038 Rev. 10/13 YAGIS ANT390Y5-WR YAGI ANTENNA 5 dBd 370 - 410 MHz 7 ANT390Y5-WR at 390 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 5.05 dBd -30 -60 The Telewave ANT390Y5-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 5 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT390Y5-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 5.14 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 370-410 MHz 5 dBd 500 watts 50 ohms / 1.5:1 (max) 19 dB 60° / 110° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 3 21 x 16 in. 4.5 lb. 8 lb. 150 / 125 MPH 0.530 ft.² 21 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7120 Rev. 10/13 267 ANT410Y10-WR YAGI ANTENNA 10 dBd 405 - 420 MHz ANT410Y10-WR at 410 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.1 dBd -30 -60 The Telewave ANT410Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT410Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 10.1 dBd 120 150 400 415 430 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 405-420 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 45 x 17 in. 8 lb. 11 lb. 150 / 125 MPH 0.42 ft.² 17 lb. 268 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7031 Rev. 10/13 YAGIS ANT420Y10-WR YAGI ANTENNA 10dBd 415 - 450 MHz 7 ANT420Y10-WR at 420 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.1 dBd -30 -60 The Telewave ANT420Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT420Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 10.1 dBd 120 150 400 430 460 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 415-450 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 41 x 13 in. 8 lb. 11 lb. 150 / 125 MPH 0.42 ft.² 17.0 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7113 Rev. 10/13 269 ANT430Y10-WR YAGI ANTENNA 10 dBd 420 - 440 MHz ANT430Y10-WR at 410 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.1 dBd -30 -60 The Telewave ANT430Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT430Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 10.1 dBd 120 150 415 425 450 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 405-420 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 45 x 17 in. 8 lb. 11 lb. 150 / 125 MPH 0.42 ft.² 17 lb. 270 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7032 Rev. 10/13 YAGIS ANT440Y10-WR YAGI ANTENNA 10 dBd 438 - 455 MHz 7 ANT440Y10-WR at 440 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.0 dBd -30 -60 The Telewave ANT440Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT440Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 10.0 dBd 120 150 430 445 460 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 438-455 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 45 x 15 in. 8 lb. 11 lb. 150 / 125 MPH 0.42 ft.² 17 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7029 Rev. 10/13 271 420 - 470 MHz ANT450Y5-WR YAGI ANTENNA 5 dBd ANT450Y5-WR at 440 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 5.2 dBd -30 -60 The Telewave ANT450Y5-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 5 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT450Y5-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 5.2 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 420-470 MHz 5 dBd 500 watts 50 ohms / 1.5:1 (max) 18 dB 64° / 116° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 3 24 x 14 in. 5 lb. 9 lb. 150 / 125 MPH 0.12 ft.² 4.8 lb. 272 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7006 Rev. 10/13 YAGIS ANT450Y7-WR YAGI ANTENNA 7 dBd 450 - 470 MHz 7 ANT450Y7-WR at 460 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 7.2 dBd -30 -60 The Telewave ANT450Y7-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 7 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds provide exceptional strength and prevent intermodulation. The ANT450Y7-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 7.2 dBd 120 150 450 460 470 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 450-470 MHz 7 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 54° / 80° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 4 29 x 13 in. 5 lb. 9 lb. 150 / 125 MPH 0.33 ft.² 13.4 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7007 Rev. 10/13 273 450 - 470 MHz ANT450Y10-WR YAGI ANTENNA 10 dBd ANT450Y10-WR at 460 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.2 dBd -30 -60 The Telewave ANT450Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT450Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 10.2 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 450-470 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 45 x 15 in. 8 lb. 11 lb. 150 / 125 MPH 0.42 ft.² 17.0 lb. 274 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7063 Rev. 10/13 YAGIS ANT475Y5-WR YAGI ANTENNA 5 dBd 450 - 512 MHz 7 ANT475Y5-WR at 480 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 5.0 dBd -30 -60 The Telewave ANT475Y5-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 5 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT475Y5-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 5.0 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 450-512 MHz 5 dBd 500 watts 50 ohms / 1.5:1 (max) 18 dB 64° / 116° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 3 17 x 13 in. 2 lb. 4 lb. 150 / 125 MPH 0.17 ft.² 6.9 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7121 Rev. 10/13 275 ANT490Y10-WR YAGI ANTENNA 10 dBd 470 - 500 MHz ANT490Y10-WR at 490 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.1 dBd -30 -60 The Telewave ANT490Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT490Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 10.1 dBd 120 150 465 487 510 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 470-500 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 42.5 x 13 in. 8 lb. 11 lb. 150 / 125 MPH 0.42 ft.² 17.0 lb. 276 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7111 Rev. 10/13 YAGIS ANT500Y10-WR YAGI ANTENNA 10 dBd 485 - 512 MHz 7 ANT500Y10-WR at 500 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.1 dBd -30 -60 The Telewave ANT500Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT500Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 10.1 dBd 120 150 480 500 520 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 485-512 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 45 x 14.5 in. 8 lb. 11 lb. 150 / 125 MPH 0.42 ft.² 17.0 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7112 Rev. 10/13 277 698 - 787 MHz ANT740Y8-WR YAGI ANTENNA 8 dBd ANT740Y8-WR at 740 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 8 dBd -30 -60 The Telewave ANT740Y8-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 8 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT740Y8-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM940H adapter can be used. The clamp set fits any vertical mast or tower support from 1.0"-2.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 8 dBd 120 150 695 742 790 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 698-787 MHz 8 dBd 500 watts 50 ohms / 1.5:1 (max) 18 dB 54° / 64° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 6 27.5 x 8 in. 3 lb. 6 lb. 200 / 165 MPH 0.3 ft.² 8.5 lb. 278 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7115 Rev. 10/13 YAGIS ANT750Y5-WR YAGI ANTENNA 5 dBd 734 - 806 MHz 7 ANT750Y5-WR at 770 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 5.2 dBd -30 -60 5.22 dBd The Telewave ANT750Y5-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 5 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT750Y5-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM940H adapter can be used. The clamp set fits any vertical mast or tower support from 1.0"-2.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. H-Plane Gain: 5.2 dBd SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 734-806 MHz 5 dBd 500 watts 50 ohms / 1.5:1 (max) 18 dB 64° / 116° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 3 13 x 8 in. 2 lb. 5 lb. 200 / 165 MPH 0.11 ft.² 4.5 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7096 Rev. 10/13 279 800 - 870 MHz ANT830Y10-WR YAGI ANTENNA 10 dBd ANT830Y10-WR at 837 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.2 dBd -30 -60 The Telewave ANT830Y10-WR is a against ice and other hazards with high performance direc tional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT830Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM940H adapter can be used. The clamp set fits any vertical mast or tower support from 1.0"-2.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 10.2 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 800-870 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 49° / 47° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 27 x 7.5 in. 3 lb. 6 lb. 200 / 165 MPH 0.25 ft.² 7.25 lb. 280 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7003 Rev. 10/13 YAGIS ANT850Y10-WR YAGI ANTENNA 10 dBd 824 - 896 MHz 7 ANT850Y10-WR at 877 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.2 dBd -30 -60 The Telewave ANT850Y10-WR is against ice and other hazards with a high performance directional a tough, RF-transparent radome. antenna, designed especially for point to point as well as point/ multipoint applications. This antenna produces 10 dBd forward gain with an excellent front-to-back ratio. Solid aluminum elements with 360° welds prevent intermodulation and provide exceptional strength. The ANT850Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM940H adapter can be used. The clamp set fits any vertical mast or tower support from 1.0"-2.5" O.D. Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the radiating element is completely sealed For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 10.2 dBd 120 150 824 861 896 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 824-896 MHz 10 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 46° / 50° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 23 x 11 in. 3 lb. 7 lb. 200 / 165 MPH 0.22 ft.² 8.7 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7061 Rev. 10/13 281 ANT930Y10-WR YAGI ANTENNA 10.5 dBd / 12.6 dBi 885 - 975 MHz ANT930Y10-WR at 930 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 H-Plane -90 Gain: 10.5 dBd -30 -60 The Telewave ANT930Y10-WR Yagi radiating element is completely is a high performance directional sealed against ice and other hazards antenna, designed especially for with a tough, RF-transparent point to point as well as point/ radome. multipoint control applications. Seven elements provide a minimum of 10.5 dBd (12.6 dBi) forward gain, excellent front-to-back performance, and coverage of the entire 900 MHz commercial band. The boom and elements are solid 360° welded aluminum to prevent intermodulation The ANT930Y10-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM940H adapter can be used. The clamp set fits any vertical mast or tower support from 1.0"-2.5" O.D. and provide exceptional strength. For installations on angled supports, Each antenna is completely protected with our high-tech TxylanTM coating, which provides icing resistance and protection from corrosive gases, UV radiation, salt spray, acid rain and wind-blown sand. The feed line is protected within the boom, and the the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 330 300 270 0 -3 -10 -20 30 60 90 240 210 E-Plane 180 Gain: 10.5 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 885-975 MHz 10.5 dBd 500 watts 50 ohms / 1.5:1 (max) 25 dB 40° / 50° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 7 28.5 x 7.5 in. 3 lb. 8 lb. 200 / 165 MPH 0.25 ft.² 10.0 lb. 282 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7016 Rev. 10/13 YAGIS ANT930Y12-WR YAGI ANTENNA 12.2 dBd / 14.3 dBi 880 - 960 MHz 7 ANT930Y12-WR at 930 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 12.2 dBd -30 -60 The Telewave ANT930Y12-WR Yagi The active element and feed line antenna is a high performance are sealed within the antenna. directional antenna, with reduced sidelobes and very high front-toback ratio. Twelve elements provide a minimum of 12.2 dBd (14.3 dBi) forward gain, and coverage of the entire 900 MHz commercial band. The boom and elements are solid 360° welded aluminum to prevent intermodulation and provide exceptional strength. The ANT930Y12-WR includes a welded vertical plate and mast clamp set. A horizontal welded plate is optional, or the ANTM400H adapter can be used. The clamp set fits any vertical mast or tower support from 1.5"-3.5" O.D. For hardline cable a 90°-angle feed option is available. All antenna components are completely protected with our high-tech TxylanTM coating, which seals the antenna against corrosive gases, UV radiation, salt spray, acid rain, and wind-blown sand in desert environments. This coating also greatly reduces ice buildup. For installations on angled supports, the Universal mount option deletes the welded clamp, providing 3 separate planes of rotation and almost any required orientation. The "U" mount attaches to virtually all supports up to 3.5" in diameter, and can be adapted to flat surfaces and utility poles. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 12.2 dBd 120 150 TYPICAL VSWR RESPONSE 1.5:1 1.4:1 1.3:1 1.2:1 1.1:1 900 930 960 FREQUENCY (MHz) SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 880-960 MHz 12.2 dBd 500 watts 50 ohms / 1.5:1 (max) 26 dB 34° / 36° Directional / Vertical N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 12 44 x 6 in. 6 lb. 11 lb. 175 / 150 MPH 0.58 ft.² 23.2 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7004 Rev. 10/13 283 ANT1470Y12-WR YAGI ANTENNA 12.2 dBd / 14.3 dBi 1425 - 1535 MHz ANT1470Y12-WR at 1470 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 12.2 dBd -30 -60 The Telewave ANT1470Y12-WR is a UV radiation, salt spray, acid rain rugged, wideband, high gain Yagi and wind-blown sand. The feed line antenna, designed for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses twelve solid brass elements, and produces 12.2 dBd forward gain with excellent front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT1470Y12-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5"-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. the antenna against corrosive gases, 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 12.2 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 1425-1535 MHz 12.2 dBd 500 watts 50 ohms / 1.5:1 (max) 17 dB 34° / 35° Directional / Variable N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 12 26 x 5 in. 2 lb. 7 lb. 200 / 165 MPH 0.18 ft.² 7.4 lb. 284 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7023 Rev. 10/13 YAGIS ANT1800Y10-WR YAGI ANTENNA 10.2 dBd / 12.3 dBi 1710 - 1880 MHz 7 ANT1800Y10-WR at 1795 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 10.2 dBd -30 -60 The Telewave ANT1800Y10-WR the antenna against corrosive gases, is a rugged, wideband, high gain UV radiation, salt spray, acid rain Yagi antenna for the DCS-1800 and wind-blown sand. The feed line band, designed for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses eight solid brass elements, and produces 10 dBd forward gain with excellent front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT1800Y10-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5"-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 10.2 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 1710-1880 MHz 10.2 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 40° / 50° Directional / Variable N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 8 19 x 3 in. 3 lb. 5 lb. 165 / 150 MPH 0.14 ft.² 5.6 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7014 Rev. 10/13 285 1850 - 1990 MHz ANT1920Y9-WR YAGI ANTENNA 9.3 dBd / 11.4 dBi ANT1920Y9-WR at 1920 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 9.3 dBd -30 -60 The Telewave ANT1920Y9-WR is the antenna against corrosive gases, a rugged, wideband, high gain UV radiation, salt spray, acid rain Yagi antenna for the broadband and wind-blown sand. The feed line PCS bands, designed for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses six solid brass elements, and produces 9.3 dBd forward gain with excellent front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT1920Y9-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 9.3 dBd 120 150 1850 1920 1990 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 1850-1990 MHz 9.3 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 46° / 56° Directional / Variable N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 6 11.75 x 3.5 in. 1 lb. 4 lb. 200 / 165 MPH 0.14 ft.² 5.6 lb. 286 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7027 Rev. 10/13 YAGIS ANT1920Y12-WR YAGI ANTENNA 12.2 dBd / 14.3 dBi 1850 - 1990 MHz 7 ANT1920Y12-WR at 1895 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 12.0 dBd -30 -60 The Telewave ANT1920Y12-WR the antenna against corrosive gases, is a rugged, wideband, high gain UV radiation, salt spray, acid rain Yagi antenna for the broadband and wind-blown sand. The feed line PCS bands, designed for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses twelve solid brass elements, and produces 12.2 dBd forward gain with excellent front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT1920Y12-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5"-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 12.0 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 1850-1990 MHz 12.2 dBd 500 watts 50 ohms / 1.5:1 (max) 22 dB 30° / 35° Directional / Variable N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 12 23 x 3.25 in. 2 lb. 6 lb. 200 / 165 MPH 0.2 ft.² 8.0 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7015 Rev. 10/13 287 ANT2045Y12-WR YAGI ANTENNA 12.2 dBd / 14.3 dBi 1920 - 2170 MHz ANT2045Y12-WR at 2045 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 12.2 dBd -30 -60 The Telewave ANT2045Y12-WR the antenna against corrosive gases, is a rugged, wideband, high gain UV radiation, salt spray, acid rain Yagi antenna for the 3G UMTS/ and wind-blown sand. The feed line PCS bands, designed for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses thirteen solid brass elements, and produces 12.2 dBd forward gain with exceptional front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT2045Y12-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5"-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 12.2 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 1920-2170 MHz 12.2 dBd 500 watts 50 ohms / 1.5:1 (max) 30 dB 30° / 35° Directional / Variable N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 13 24 x 3.75 in. 1.6 lb. 6 lb. 175 / 150 MPH 0.12 ft.² 4.6 lb. 288 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7088 Rev. 10/13 YAGIS ANT2350Y12-WR YAGI ANTENNA 12 dBd / 14.1 dBi 2300 - 2500 MHz 7 ANT2350Y12-WR at 2400 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 12.0 dBd -30 -60 The Telewave ANT2350Y12-WR is a the antenna against corrosive gases, rugged, wideband, high gain Yagi UV radiation, salt spray, acid rain antenna for the WiFi and amateur 13 and wind-blown sand. The feed line cm bands, designed for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses 12 solid brass elements, and produces 12 dBd forward gain with exceptional front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT2350Y12-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5"-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 12.0 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 2300-2500 MHz 12 dBd 500 watts 50 ohms / 1.5:1 (max) 19 dB 36° / 38° Directional / Variable N Female or 7-16 DIN (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 12 18.5 x 3.25 in. 1.5 lb. 4 lb. 175 / 150 MPH 0.1 ft.² 4.1 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7123 Rev. 10/13 289 ANT2400Y12-WR YAGI ANTENNA 12 dBd / 14.1 dBi 2400 - 2500 MHz ANT2400Y12-WR at 2450 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 12.0 dBd -30 -60 The Telewave ANT2400Y12-WR is a the antenna against corrosive gases, rugged, wideband, high gain Yagi UV radiation, salt spray, acid rain antenna for the WiFi and amateur 13 and wind-blown sand. The feed line cm bands, designed for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses ten solid brass elements, and produces 12 dBd forward gain with exceptional front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT2400Y12-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5"-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. 330 300 270 0 -3 -10 -20 30 60 90 240 210 H-Plane 180 Gain: 12.0 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 2400-2500 MHz 12 dBd 500 watts 50 ohms / 1.5:1 (max) 30 dB 34° / 35° Directional / Variable N Female or 7-16 DIN-F (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 10 17.75 x 3.5 in. 1.25 lb. 6 lb. 165 / 150 MPH 0.09 ft.² 3.6 lb. 290 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7008 Rev. 10/13 YAGIS ANT2600Y12-WR YAGI ANTENNA 12 dBd / 14.1 dBi 2500 - 2700 MHz 7 ANT2600Y12-WR at 2600 MHz 90 60 60 -3 30 -10 30 -20 0 0 -30 -60 E-Plane -90 Gain: 12.0 dBd -30 -60 The Telewave ANT2600Y12-WR the antenna against corrosive gases, is a rugged, wideband, high gain UV radiation, salt spray, acid rain Yagi antenna for the WiMAX/LTE and wind-blown sand. The feed line bands, designed for for handheld is sealed within the antenna boom, use with many types of portable and an RF-transparent radome wireless analyzers. This antenna protects the driven element from can also be installed for fixed use corrosion or icing. in any environment. The antenna uses 12 solid brass elements, and produces 12 dBd forward gain with excellent front-to-back performance. Construction and design are optimized to prevent RF intermodulation, and ensure precise pattern control. The ANT2600Y12-WR includes a small U-clamp and plates that allow the antenna to be mounted for vertical or horizontal polarization. The clamp set can be attached to any vertical mast or tower support between 0.5"-1.125" O.D. The Universal mount option allows Eac h antenna is completely mounting to angled supports up protected with Telewave's high- to 3.5" O.D., and continuous tilt tech TxylanTM coating, which seals adjustment. 0 330 -3 300 -10 -20 270 30 60 90 240 210 H-Plane 180 Gain: 12.0 dBd 120 150 SPECIFICATIONS Frequency (continuous) Gain (typ) Power rating (typ) Impedance / VSWR Front to back ratio (min) Beamwidth V / H Pattern / Polarization Termination 2500-2700 MHz 12 dBd 500 watts 50 ohms / 1.5:1 (max) 20 dB 36° / 40° Directional / Variable N Female or 7-16 DIN-F (opt) Elements Dimensions (L x H) Antenna weight Shipping weight Wind rating / with 0.5" ice Exposed area (flat plate equiv.) Lateral thrust at 100 MPH (40 psf - flat plate equiv.) 12 17.25 x 3 in. 1.0 lb. 3 lb. 175 / 150 MPH 0.08 ft.² 3.2 lb. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7062 Rev. 10/13 291 138 - 960 MHz INSTALLATION GUIDE FOR YAGI ANTENNAS WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. BEFORE ASSEMBLING AND MOUNTING: Carefully read all instructions and study the diagrams. Check to make sure you have all parts. PARTS LIST (Fig. 1) (1) Antenna assy. (1) Mounting plate (4) 5/16-18 x 4.0" threaded rod (2) 5/16-18 x 1.0" bolt (10) 5/16" Hex nuts (8) 5/16" Lock washers (1) Anti-seize compound Figure 1 (2) ANTIROTATION (4) 5/16" BOLT MAST MOUNTING INSTRUCTIONS 1. Apply anti-seize compund to all rod ends. Attach mounting and antenna boom plates to the mast with (4) 5/16" rods per Fig. 1. The mounting and boom plates are grooved to provide self alignment for vertical orientation. The driven element radome should be pointing down. 2. Tighten the hex nuts until all lock washers are flat, then add 1/2 turn to each. Tighten the anti-rotation bolts and jam nuts to resist turning forces on the antenna. 3. The antenna input connector is a Type N or 7-16 DIN Female. Connect the RF feed cable to the antenna output connector. Secure all cables with cable ties. Fig. 2 illustrates a typical method for connecting the RF cable, with a feed cable service loop. 4. Be sure to properly seal the input connector with waterproof tape or other sealing material. See Telewave TWDS-0502 for a recommended method of connector sealing. Figure 2 ANT. BOOM MAST REFLECTOR ELEMENT RF CONNECTOR ANTIROTATION MOUNTING PLATE CABLE TO RADIO CABLE TIE DRIVEN ELEMENT Note: Driven element with radome should be pointing down for vertical polarization. 292 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7081 Rev. 4/11 INSTALLATION GUIDE FOR YAGI ANTENNAS 1.0 - 2.7 GHz 7 YAGIS WARNING: For your safety, do not install any antenna near power lines, and carefully follow all installation instructions. If the antenna falls toward or contacts any overhead wires, immediately let go and stay away. Call the utility company for assistance. Always use safety devices for tower climbing. Ensure that the tower structure is well grounded for lightning protection. BEFORE ASSEMBLING AND MOUNTING: Carefully read all instructions and study the diagrams. Check to make sure you have all parts. PARTS LIST (Figure 1) (1) Antenna assy. (2) Mounting plates (1) 5/16-18 U-bolt (2) 5/16" Hex nuts (2) 5/16"Lock washers (1) Anti-seize compound Figure 1 MOUNTING INSTRUCTIONS 1. Apply anti-seize compund to U-bolt ends. Loosely attach mounting plate with 2 grooves and antenna clamp plate to the mast with U-bolt per Fig. 1. Slide the antenna boom end into the groove in the mounting plates, and rotate the antenna elements according to the requirements of the application. The driven element radome should be pointing down for vertical operation. 2. Tighten the hex nuts until the lock washers are flat, then add 1/2 turn. 3. The antenna input connector is a Type N or 7-16 DIN Female. Connect the RF feed cable to the antenna input connector. Secure all cables with cable ties. Fig. 2 illustrates a typical method for connecting the RF cable, with a feed cable service loop. 4. Be sure to properly seal the input connector with waterproof tape or other sealing material. See Telewave TWDS-0502 for a recommended method of connector sealing. Figure 2 ANT. BOOM RF CONNECTOR MAST REFLECTOR ELEMENT MOUNTING PLATE CABLE TO RADIO DRIVEN ELEMENT CABLE TIE Note: Driven element with radome should be pointing down for vertical polarization. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7082 Rev. 10/13 293 WIDEBAND ANTENNAS 30 - 3000 MHz Telewave Wideband Directional antennas offer a simple, rugged package for RF testing, troubleshooting and coverage analysis. Telewave Wideband Discone antennas combine proven designs and ultra-rugged construction to withstand the most extreme conditions. Broad beamwidth enables communication over hundreds of miles from mountain-top sites to aircraft, with frequency coverage as wide as 30-3000 MHz in one antenna. Telewave Discone antennas are fabricated from solid 6061-T6 aluminum, and completely welded for maximum strength and electrical performance. Each antenna is fully coated with our hightech TxylanTM coating, which provides total protection from water, corrosive chemicals, salt spray, and windblown abrasives. This smooth black coating also dramatically reduces surface friction, reducing and often preventing ice adhesion, while improving absorption of solar radiation. The ANT260KT is also available with Desert Tan coating, offering all the same benefits and clean visual integration in a desert environment. The ANT280S is light enough to be used as a tactical antenna for field deployment, and can complement or replace multiple antennas on a mobile command vehicle. The 500 watt power rating allows use of high-power radios and tactical repeaters. The standard connector type is N Female, and a 7-16 DIN-F can be installed as an option for higher power applications. 294 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7124 Rev. 10/13 ANT220K WIDEBAND DISCONE ANTENNA 30 MHz - 3 GHz 7 WIDEBAND The Telewave ANT220K is an extremely rugged, wideband discone antenna for all frequencies between 30 MHz and 3 GHz. The wide vertical beamwidth of discone antennas allows clear communication for ground and ground-to-air applications. Telewave discone antennas are designed to survive the most extreme conditions, where conventional antennas often fail. They are field-proven in US and overseas deployments and support many voice and data requirements in multiple bands. The radome and TxylanTM coating on all metal surfaces ensures complete protection from corrosive gases, ultraviolet radiation, salt spray, acid rain and sand storms in desert environments. The ANT220K is designed to be clamped to a 1.5"-3.5" diameter galvanized steel support pipe. An ANTC482 dual clamp set is included. Each discone is constructed from Mil. Spec. 6061-T6 solid aluminum, fully welded at all joints for maximum strength. All internal junctions are enclosed within a ruggedized radome to ensure survivability in the worst environments. ANTC482 SPECIFICATIONS (PRELIMINARY) Frequency (continuous) 30 MHz - 3000 MHz Power rating (typ.) 500 watts Gain (typ.) 0 dBd Impedance 50 ohms VSWR 2.5:1 or less Pattern Termination Omnidirectional N-Male or 7-16 DIN on RG-393 feed cable Vertical beamwidth (nom.) Wind rating / 0.5" ice 110 degrees (varies with frequency) 150 / 125 MPH Maximum exposed area 2.25 ft.² Lateral thrust at 100 MPH 90 lb Bending moment at 100 MPH 180 ft. lb (top clamp, flat plate equiv.) Dimensions 58" H x 38" W (at skirt base) Weight (antenna + clamps) 61 lb Shipping weight 110 lb 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 E-plane: 100 MHz -90 -30 -60 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 E-plane: 400 MHz -90 -30 -60 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7125 Rev. 10/13 295 75 MHz - 3 GHz ANT260K, KT WIDEBAND DISCONE ANTENNA The Telewave ANT260K is an extremely rugged, wideband discone antenna for all frequencies between 75 MHz and 3 GHz. The wide vertical beamwidth of discone antennas allows clear communication for ground and ground-to-air applications. Telewave discone antennas are designed to survive the most extreme conditions, where conventional antennas often fail. They are field-proven in US and overseas deployments and support many voice and data requirements in multiple bands. The radome and TxylanTM coating on all metal surfaces ensures complete protection from corrosive gases, ultraviolet radiation, salt spray, acid rain and sand storms in desert environments. The ANT260K is designed to be clamped to a 1.5"-3.5" O.D. galvanized steel support pipe. An ANTC482 dual clamp set is included. The ANT260KT is coated in Desert Tan for deployment in desert environments. Each discone is constructed 3.0 from Mil. Spec. 6061-T6 solid aluminum, fully welded at all 2.5 joints for maximum strength. All V S internal junctions are enclosed W R within a ruggedized radome to ANTC482 2.0 ensure survivability in the worst environments. 1.5 SPECIFICATIONS Frequency (continuous) Power rating (typ.) Gain (typ.) Impedance VSWR Pattern Termination Vertical beamwidth (nom.) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at 100 MPH Dimensions Weight (antenna + clamps) Shipping weight 75 MHz - 3 GHz (75-95 MHz at 2:1 VSWR) 500 watts 0 dBd 50 ohms 1.5:1 or less in band Omnidirectional N-Male or 7-16 DIN on RG-393 feed cable 110 degrees 200 / 150 MPH 1.67 ft.² 66 lb 133 ft. lb (top clamp, flat plate equiv.) 53" H x 26" W (at base) 52 lb 102 lb 1.25 50 100 200 300 400 500 FREQUENCY (MHZ) 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 E-plane: 100 MHz -90 90 60 -3 30 -10 -20 0 -30 -60 60 30 0 -30 -60 E-plane: 400 MHz -90 -30 -60 296 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7090 Rev. 10/13 ANT280S WIDEBAND DISCONE ANTENNA 118 MHz - 3 GHz 7 WIDEBAND The Telewave ANT280S Discone is a rugged, lightweight, wideband antenna for all frequencies between 118 MHz and 3 GHz. This versatile antenna provides a highly flexible solution to interoperability requirements in multiple bands. Each antenna is constructed from Mil. Spec. 6061-T6 solid aluminum, welded at all joints for maximum strength. A high-strength radome encloses the upper cone and RF connections to ensure survivability in adverse environments. The radome and TxylanTM coating on all metal surfaces ensures complete protection from corrosive gases, ultraviolet radiation, salt spray, acid rain and sand storms in desert environments. The antenna has a 1.5" diameter mast and a dual clamp kit is available for mounting to a 1.5"3.5" O.D. support pipe. SPECIFICATIONS Frequency (continuous) Power rating (typ.) Gain (typ.) Impedance VSWR Pattern Termination Vertical beamwidth (nom.) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at 100 MPH Dimensions Weight The ANT280S is light enough to be used as a tactical antenna for field deployment, and can complement or replace multiple antennas on a mobile command vehicle. The 500 watt power rating allows use of high-power radios and tactical repeaters. The full-surface coating and rugged construction means it can also be permanently mounted on a tower or command center roof for long-term fixed operation. The ANT280S is ready to operate with a single or multiband radio using one antenna output. Several types of low-loss couplers are available for multi-radio operation. For optimum performance in the lowest frequency ranges, the antenna should be mounted at least 20 feet above the closest reflecting surface. 118 MHz - 3 GHz 500 watts 0 dBd 50 ohms 1.5:1 or less (118 - 136 MHz at 1.8:1 VSWR) Omnidirectional N-Male or 7-16 DIN (option) on feed cable 110° 150 / 100 MPH 0.89 ft.² 36 lb 49 ft. lb (top clamp, flat plate equiv.) 43" H x 28.5" W (at base) 11 lb -14 / 1.5:1 TYPICAL VSWR RESPONSE -16 / 1.4:1 -18 / 1.3:1 -20 / 1.22:1 -22 / 1.17:1 -24 / 1.13:1 -26 / 1.11:1 dB / VSWR 130 400 700 1000 1300 1600 1900 2200 2500 2800 3000 FREQUENCY (MHz) 60 30 90 -3 -10 -20 60 30 0 0 -30 -60 E-plane: 136 MHz -90 90 60 -3 30 -10 -20 0 -30 -60 60 30 0 -30 -60 E-plane: 400 MHz -90 -30 -60 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7108 Rev. 10/13 297 400 MHz - 3 GHz ANT400K, KS WIDEBAND DISCONE ANTENNA The Telewave ANT400K is an extremely rugged, wideband discone antenna for all frequencies between 400 MHz and 3 GHz. The wide vertical beamwidth of discone antennas allows clear communication for ground, sea, and ground-to-air applications. Telewave discone antennas are designed to survive the most extreme conditions, where conventional antennas often fail. They are field-proven in military deployments and the offshore oil and gas industry, and support many voice and data requirements in multiple bands. The radome and TxylanTM coating on all metal surfaces ensures complete protection from corrosive gases, ultraviolet radiation, salt spray, acid rain and sand storms in desert environments. The ANT400K is designed to be clamped to a 1.5"-3.5" diameter galvanized steel support pipe. An ANTC482 dual clamp set is included. The ANT400KS is provided with a shortened support mast for compact installations. Each discone is constructed from Mil. Spec. 6061-T6 solid aluminum, fully welded at all joints for maximum strength. All internal junctions are enclosed within a ruggedized radome to ensure survivability in the worst environments. ANT400KS IN OFFSHORE DEPLOYMENT SPECIFICATIONS Frequency (continuous) Power rating (typ.) Gain (typ.) Impedance VSWR Pattern Termination Vertical beamwidth (nom.) Wind rating / 0.5" ice Maximum exposed area Lateral thrust at 100 MPH Bending moment at 100 MPH Dimensions Weight (antenna + clamps) Shipping weight 400 MHz - 3 GHz 500 watts 0 dBd 50 ohms 1.5:1 or less in band Omnidirectional N-Male or 7-16 DIN (option) on RG-393 feed cable 110 degrees 200 / 150 MPH 1.13 ft.² 46 lb 74 ft. lb (top clamp, flat plate equiv.) 48" H x 8" W (at base) 32 lb 41 lb 3.0 2.5 V S W R 2.0 1.5 1.25 400 1700 FREQUENCY (MHZ) 3000 60 30 0 90 -3 -10 -20 60 30 0 -30 -60 E-plane: 450 MHz -90 -30 -60 298 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7092 Rev. 10/13 WIDEBAND ANT500WR WIDEBAND DIRECTIONAL ANTENNA 500 MHz - 3 GHz 7 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 E Plane -60 -60 -90 550 MHz H Plane 330 0 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 The Telewave ANT500WR is a lightweight, broadband directional antenna for interference location, in-building testing, and RF coverage measurement. The antenna is enclosed in a rugged, weatherproof housing, and includes a hand grip for accurate pointing and polarization. A flexible 5 ft. N-male jumper is also included. 60 30 0 90 -3 -10 -20 60 30 0 -30 -30 E Plane -60 -60 -90 SPECIFICATIONS Frequency (continuous) Power rating (typ.) VSWR Impedance Pattern Termination Gain (frequency dependent) Enclosure dimensions (H x W x D) Weight 500 MHz - 3 GHz 500 watts 2.5:1 or less 50 ohms Directional N-Female 4-7 dBi 10.5" x 13.5" x 1.25" 2.5 lb. 2000 MHz H Plane 330 0 -3 300 -10 -20 270 30 60 90 240 120 210 150 180 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7114 Rev. 10/13 299 ANTENNA MOUNTING HARDWARE ANTC482 The ANTC482 Mounting Clamp Kit is fabricated from heavy-duty galvanized steel, with stainless steel fasteners. The middle clamps are separate for more flexible installation. Designed for mounting to square or round member towers from 1.5"-3.5" O.D. Two complete clamp sets are included in the kit. This clamp set can also be used in a 90-degree crossover configuration. ANTM432 The ANTM432 is an insulated top support bracket for Telewave F68-10 collinear antennas. It is field-adjustable from 32"-43" from the tower. The boom is fabricated from UV-resistant PVC, and will not disrupt the VSWR or pattern of the antenna. (1) ANTC484 clamp and (2) steel band clamps are included with the kit. ANTC483 / ANTC483SS The ANTC483 Mounting Clamp Kit is fabricated from heavy-duty galvanized steel, with stainless steel fasteners. The 483SS model clamps are fabricated from stainless steel. The middle clamps are welded at the center. Designed for mounting to square or round member towers from 1.5"-3.5" O.D. Two complete clamp sets are included in the kit. ANTM431 The ANTM431 is a top support bracket, designed to provide proper top support for a mast only. It is constructed from heavy galvanized steel. The bracket is adjustable from 13 to 21 inches from the tower. The kit includes (1) ANTM431, (1) ANTC484 Mounting Clamp, and (1) adjustable steel band clamp. ANTS420 The ANTS420 Mast Shim Set allows mounting of Telewave folded dipoles to a 1.25 inch diameter mast or tower leg. One shim set is required for each dipole clamp. ANTM433 The ANTM433 Side Mount Kit is designed to mount an antenna 15 inches from a tower. It is fabricated from heavy-duty galvanized steel. (2) ANTC484 clamps are included in the kit. ANTC484 The ANTC484 mounting clamp consists of a steel V-bolt assembly and associated hardware, combined with a back plate of heavy-duty galvanized steel. It will mount to 3-inch round members or 2-inch angled members. ANTC485 Dual U Bolt clamp set for F2 series collinears. For mounting to round member towers from 1.5"-3" O.D. ANTM434 The ANTM434 Adjustable Side Mount Kit mounts across a tower face to provide a standoff mounting configuration. The antenna can be positioned 2 to 8 feet from the tower. Mounting hardware is galvanized steel. Supplied without support booms or mast. For use on tower legs from 1.5"-3.5" O.D. ANTM434-M Includes support booms. 2 inch Sch. 40 galvanized steel. Tower (Mast not supplied) Support booms 300 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7046 Rev. 10/13 ANTENNA CONNECTION WEATHERPROOFING 7 The primary purpose of wrapping a connection is to seal it against moisture intrusion. The procedure illustrated here will give excellent results if done properly, and will last for years. The required materials are shown below: vinyl tape, butyl tape, mastic, and Scotch-Kote. After a connection has been made and tested to verify that it has been properly done, it needs to be sealed. Begin by wrapping vinyl tape as shown to cover the connectors and a portion of both cables. Stretch the tape a minor amount as it is wound onto the cable, the connectors and then onto the other cable. Wrap this so that each new layer covers half of the previous wrap. Keep the wraps neat and as smooth as possible. The second step is to wrap a second layer over the first layer, but wrap it in the other direction as shown. These two layers will keep the connection clean and tight. The next step is to wrap a layer of vinyl tape with the adhesive side out, as shown. Begin by folding the tape onto itself at a 45 degree angle. This provides a sticky surface to help bond the the next layer of tape to the connection. The next step is to wrap the entire connection with the butyl tape. This layer provides the majority of the moisture shielding. The final step is to coat the entire butyl layer with Scotch-Kote. Coat a portion of each cable and the entire final layer of tape. This material works very quickly to fuse the last layer together and to the cable jacket. After the Scotch-Kote has dried, encapsulate the finished connection with the mastic material. It is best to secure the cable to the support on either side of the connection, not over the connection. One tie on each side is best, and spaced so as to support the connection, but not to disrupt the surface of the seal. This provides support, but will not compromise the seal you have just made. Added insurance against abrasion may be achieved by placing a single layer of vinyl tape onto the support where the connection will rest before tying the cable down. This provides some cushioning between the connection and the support. Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-0502 Rev. 2/10 301 24 - 72 MHz ANTPD 204, 206 LOW BAND RF POWER DIVIDERS Telewave Low Band RF Power Dividers divide up to 500 Watts of power from a single source over 2 outputs. These dividers are available in two overlapping frequency bands from 24 MHz to 72 MHz, with very low VSWR and insertion loss. Power is divided equally to each output port. Telewave power dividers are custom machined from solid 6061- T6 aluminum stock. These devices utilize solid metal conductors for all internal RF paths, enabling high power handling and extremely low insertion loss. No coaxial cabling This poly-polar coating beads of any kind is used internally, and water, and is chemically bonded no tuning is required for full band to the metal surface of the device, coverage. The standard connector reducing and often preventing ice type is N Female, and 7-16 DIN can adhesion, and does not chip or also be supplied as an option for flake. higher power applications. In situations where port-to-port Telewave power dividers also isolation is not required, Telewave feature our high-tech TxylanTM power dividers can also be used to coating, which provides exceptional feed two receivers from a common protection from water, corrosive antenna, with less than 0.25 dB chemicals, salt spray, and windblown insertion loss. abrasives. ANTPD206 SPECIFICATIONS Frequency range Input power (typ) Impedance VSWR Insertion loss (total to all ports) Power division (2 way) Connectors Dimensions (HWD) in. (cm) Weight lb. (kg) 204: 24-54 MHz 206: 45-72 MHz 500 watts 50 ohm 1.3:1 or less 0.15 dB or less 50% N Female or 7-16 DIN (opt.) 204: 76 x 1 x 1 (193 x 2.5 x 2.5) 206: 51 x 1 x 1 (129.5 x 2.5 x 2.5) 204: 9 (4.1) 206: 6 (2.7) 302 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com ANTPD204 All specifications subject to change without notice TWDS-7099 Rev. 2/07 ANTPD SERIES RF POWER DIVIDERS 24 - 2500 MHz 7 POWER DIVIDERS Telewave RF Power Dividers divide up to 500 Watts of power from a single source over 2, 3, or 4 outputs. Dividers are available in overlapping frequency bands from 24 MHz to 2.5 GHz, with very low VSWR and insertion loss. Power is divided equally to each output port. Telewave power dividers are custom machined from solid 6061T6 aluminum stock. These devices utilize solid metal conductors for all internal RF paths, enabling 500 watt continuous power handling and extremely low insertion loss. No coaxial cabling of any kind is used internally, and no tuning is required for full band coverage. The standard connector type is N Female, and 7-16 DIN can also be supplied as an option for high power applications. Telewave power dividers also feature our high-tech TxylanTM coating, which provides exceptional protection from water, corrosive chemicals, salt spray, and windblown abrasives. This poly-polar coating beads water, and is chemically bonded to the metal surface of the device, and does not chip or flake. The size and shape of these dividers lends itself to many possible mounting applications, including panels, masts, or tower legs, providing maximum installation flexibility. In situations where port-to-port isolation is not required, Telewave power dividers can also be used to feed several receivers from a common antenna, with less than 0.25 dB insertion loss. FREQUENCY RANGES ANTPDx04 24-54 MHz ANTPDx06 45-72 MHz ANTPDx08 65-110 MHz ANTPDx1 90-210 MHz ANTPDx2 180-250 MHz ANTPDx3 250-450 MHz ANTPDx4 350-600 MHz ANTPDx7 675-850 MHz ANTPDx8 760-920 MHz ANTPDx9 900-1100 MHz ANTPDx14 1350-1600 MHz ANTPDx18 1700-2050 MHz ANTPDx24 2000-2500 MHz POWER DIVISION (equal output to each port) ANTPD2xx 2 - Way 50% ANTPD3xx 3 - Way 33.3% ANTPD4xx 4 - Way 25% ANTPD424 ANTPD28D ANTPD34 ANTPD21 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7001 Rev. 10/13 303 ANTPD SERIES RF POWER DIVIDERS 24 - 2500 MHz SPECIFICATIONS Frequency range 24-2500 MHz Input power (typ) 500 Watts Impedance 50 ohms VSWR (max) 1.3:1 Connectors N Female or 7-16 DIN (opt.) INSERTION LOSS (total - from input to all output ports) ANTPDx04, x06, x08, x1 24-110 MHz 0.1 dB ANTPDx2 180-250 MHz 0.15 dB ANTPDx3 250-450 MHz 0.18 dB ANTPDx4, x7, x8 350-920 MHz 0.2 dB ANTPDx9, x14, x18, x24 900-2500 MHz 0.22 dB MODEL N FEMALE DIMENSIONS WEIGHT MODEL ANTPDx04 76" L x 1.125" x 1.125" 9 lb. ANTPDx04D ANTPDx06 51" L x 1.125" x 1.125" 6 lb. ANTPDx06D ANTPDx08 38.5" L x 1.125" x 1.125" 5.5 lb. ANTPDx08D ANTPDx1 21" L x 1.125" x 1.125" 4.5 lb. ANTPDx1D ANTPDx2 15.5" L x 1.125" x 1.125" 3.5 lb. ANTPDx2D ANTPDx3 11" L x 1.125" x 1.125" 3 lb. ANTPDx3D ANTPDx4 8.5" L x 1.125" x 1.125" 2 lb. ANTPDx4D ANTPDx7 5.5" L x 1.125" x 1.125" 1.5 lb. ANTPDx7D ANTPDx8 5.25" L x 1.125" x 1.125" 1.5 lb. ANTPDx8D ANTPDx9 5" L x 1.125" x 1.125" 1.5 lb. ANTPDx9D ANTPDx14 3.5" L x 1.125" x 1.125" 1 lb. ANTPDx14D ANTPDx18 3.25" L x 1.125" x 1.125" 1 lb. ANTPDx18D ANTPDx24 3.0" L x 1.125" x 1.125" 1 lb. ANTPDx24D 7-16 DIN DIMENSIONS 76.25" L x 1.125" x 1.125" 51.25" L x 1.125" x 1.125" 38.75" L x 1.125" x 1.125" 21.25" L x 1.125" x 1.125" 15.75" L x 1.125" x 1.125" 11.25" L x 1.125" x 1.125" 8.75" L x 1.125" x 1.125" 5.75" L x 1.125" x 1.125" 6.0" L x 1.125" x 1.125" 5.25" L x 1.125" x 1.125" 3.75" L x 1.125" x 1.125" 3.5" L x 1.125" x 1.125" 3.25" L x 1.125" x 1.125" WEIGHT 11 lb. 7 lb. 6.5 lb. 5.5 lb. 4.5 lb. 4 lb. 3 lb. 2.5 lb. 2.5 lb. 2.5 lb. 2 lb. 2 lb. 2 lb. 304 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7001 Rev. 10/13 CROSSBAND COUPLERS TS-15xx, TS-22xx, TS-46/47xx SERIES CROSSBAND COUPLERS Telewave Crossband Couplers allow transmitters, receivers, and antennas in the 150, 220, 450, and 700/800 MHz bands to share a common feedline. A single coupler can be used to couple two radios to a multiband antenna, or a multiband radio to two antennas. Two couplers are used with two radios and two antennas. The ability to share a feedline between systems on different bands simplifies installation, while reducing cost and tower loading. No tuning is required for full band coverage, and each unit is completely weathersealed for zero maintenance and long service. 132 - 960 MHz 7 TS-4680-DIN MODEL FREQUENCY RANGE POWER TS-1545 132-174 & 406-470 MHz 150 watts TS-1546 132-174 & 450-512 MHz 150 watts TS-1570 132-174 & 763-869 MHz 150 watts TS-1580 132-174 & 806-902 MHz 150 watts TS-1590 132-174 & 850-960 MHz 150 watts TS-2246 219-225 & 406-512 MHz 150 watts TS-1545H 132-174 & 406-470 MHz 400 watts TS-1546H 132-174 & 450-512 MHz 400 watts TS-1570H 132-174 & 763-869 MHz 400 watts TS-1580H 132-174 & 806-902 MHz 400 watts TS-1590H 132-174 & 850-960 MHz 400 watts TS-2246H 219-225 & 406-512 MHz 400 watts TS-4670 440-470 & 763-869 MHz 400 watts TS-4680 440-470 & 806-870 MHz 400 watts TS-4690 440-470 & 896-932 MHz 400 watts TS-4770 470-512 & 763-869 MHz 400 watts TS-4780 470-512 & 896-932 MHz 400 watts TS-154676 150-174 / 450-470 / 763-869 MHz 400 watts TS-22XX, COMMON SPECIFICATIONS TS-15XX TS-46/47XX Impedance / VSWR (typ/max) 50 ohms / 1.3:1 / 1.5:1 Isolation (min / typ.) 23 dB / 27 dB 25 dB / 30 dB Insertion loss per pair (max) 0.2 dB Temperature range -30°C to +60°C Connectors N Male or Female, 7-16 DIN M/F (opt.) Dimensions (HWL) in. 1.5 x 2.25 x 3.75 1 x 1.5 x 6.5 Weight lb. 0.5 1 ANT 156 MHz TX 156 MHz TS-1580 ANT 851 MHz TX 851 MHz Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-7110 Rev. 6/10 305 8 TECHNICAL NOTES 8 TECHNICAL NOTES TUNING INSTRUCTIONS · Single / Dual Isolators · Pass-Reject Cavity and Duplexer · Pass Cavity · VSWR / Return Loss SINGLE FERRITE ISOLATORS TUNING INSTRUCTIONS The following tuning instructions are provided for use when only a wattmeter is available. Tuning range with this method is approximately +/- 1 MHz at VHF, +/- 2 MHz at UHF, and +/- 5 MHz at 800/900 MHz. Maximum tuning range requires a more complex procedure and a network analyzer, and is also available from Telewave for a nominal fee. The initial tuning should be done at the lowest power available to reduce the possibility of damage to the transmitter or cavities during the tuning procedure. The transmitter must be turned off to prevent damage to the output stages whenever connections are changed. Install the isolator in its permanent mounting position if possible. Connect the cable from the transmitter directly to the isolator port A (Fig. I). Remove the snap plugs from adjustment holes #1, and #2. Adjustment #3 is factory set and should not be changed. Connect a terminating wattmeter, or a wattmeter with a load attached, to the output port B. Using a non-metallic tool, tune adjustment #1 and #2 for a maximum reading. Remove the wattmeter and the dummy load and connect the antenna or cavity to the isolator (Fig. 2). Remove the supplied termination from port C and install the wattmeter and termination in its place. Now tune the cavity* for a minimum reading through the wattmeter. This will establish the highest Q of the cavity and maximum power to the antenna. Adjustment #2 may be "touched up" at this time. Adjust for a minimum reading on the wattmeter. If the reading is high or the load becomes hot, problems may exist with the antenna or transmission line. Further testing should be done. When testing / tuning is complete, remove the wattmeter and reconnect the supplied termination to port C. *When a cavity is under power, high RF currents and voltages exist on the internal surfaces. Tuning under full TX power may damage the cavity. If there are no other options, use the lowest power available with minimum tuning adjustments. FIGURE 1 ISOLATOR TX A1 2 B 3 WATTMETER C LOAD LOAD FIGURE 2 ANTENNA ISOLATOR TX A1 2 B 3 C CAVITY WATTMETER LOAD 308 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-8013 Rev. 3/11 DUAL FERRITE ISOLATORS 8 BASIC TUNING INSTRUCTIONS TECHNICAL NOTES The following tuning instructions are provided for use when only a wattmeter is available. Tuning range with this method is approximately +/- 1 MHz at VHF, +/- 2 MHz at UHF, and +/- 5 MHz at 800/900 MHz. Maximum tuning range requires a more complex procedure and a network analyzer, and is also available from Telewave for a nominal fee. The initial tuning should be done at the lowest power available to prevent damage to the transmitter or cavities during the tuning procedure. Turn the transmitter off to prevent damage whenever connections are changed. This procedure can also be used to tune 2 single isolators joined with a barrel connector. Install the isolator in its permanent mounting position if possible. Connect the cable from the transmitter directly to the isolator port A (Fig. 1). Remove the snap plugs from adjustment holes #1, #2, #3 and #4. Adjustment #5 & #6 are factory set and should not be changed. Connect a terminating wattmeter, or a wattmeter with an appropriate load attached, to the output port B. Using a non-metallic tool, tune adjustment #1, #2, #3, & #4 for a maximum reading. Special Note - Models T-7560 and T-8660 do not have a hole #3. This is not required above 700 MHz. Models in all bands may have reversed connections for cable routing. (Fig. 4) Port numbers always have the same function, regardless of location. Remove the wattmeter and the dummy load and connect the antenna and cavity to the isolator. Remove the supplied termination from port C and connect the wattmeter and termination in its place (Fig. 2). Now tune adjustment #2 & #3 for minimum reading on the wattmeter. Retune these adjustments several times to ensure a minimum reading. Remove the wattmeter and termination, and reconnect the original termination to port C. Next, remove the termination from port D and install the wattmeter & load in its place (Fig. 3). Now tune adjustment #4 for minimum reading on the wattmeter. Finally, tune the cavity* (Fig. 3) for a minimum reading through the wattmeter. This will establish the highest Q of the cavity and maximum power to the antenna. Adjustment #4 may be "touched up" at this time. Adjust for a minimum reading on the wattmeter. If the reading is high or the load becomes hot, problems may exist with the antenna or transmission line. Further testing should be done. When testing / tuning is complete, remove the wattmeter and reconnect the supplied termination to port D. *When a cavity is under power, high RF currents exist on the internal surfaces. Tuning under full power may damage the cavity. If there are no other options, use the lowest power available with minimum tuning adjustments. FIGURE 1 TX ISOLATOR A B 1 23 4 6 C 5 D WATTMETER LOAD LOAD LOAD FIGURE 3 TX ISOLATOR A 1 2 6 C B 3 4 5 D ANTENNA CAVITY LOAD WATTMETER FIGURE 2 ISOLATOR ANTENNA FIGURE 4 LOAD TX A 1 2 6 C B 3 4 5 D CAVITY WATTMETER LOAD WATTMETER ISOLATOR B4 5 2 DC 1A 6 TX ANTENNA CAVITY ISOLATOR B 4 5 D A 2 1 6 C WATTMETER LOAD LOAD TX LOAD LOAD LOAD LOAD Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-8005 Rev. 3/11 309 PASS CAVITY TUNING IMPORTANT: All cavities and cavity-based devices are factory tuned to the exact frequencies indicated on the label. No further tuning or optimization is necessary. If frequency or insertion loss must be changed, Telewave recommends that the equipment be returned to the factory to ensure optimum performance. The instructions in this document are for use only if factory service is not practical. TEST EQUIPMENT MINIMUM REQUIREMENTS: 1. Calibrated RF signal generator with 0 dBm output. 2. Calibrated frequency counter or meter. 3. Calibrated RF indicator such as a network analyzer or spectrum analyzer, with sensitivity of at least 80 dB below the RF generator output. Tools required: 7/16" wrench and nut-driver, medium and small flat-blade screwdrivers. NOTE: When transmitter power is passing through a cavity, high RF voltages and currents exist on the internal surfaces. Cavity tuning should be performed using a signal generator only. If no other RF source is available, use the lowest output power available and make only minimal adjustments. 1. TUNING THE PASS FREQUENCY A. Adjust the signal generator to the desired pass frequency at 0 dBm output. B. Connect the signal generator to one cavity connector, and the monitor or analyzer to the other side. C. Loosen the 7/16" locking nut on the center tuning shaft, and tune the shaft of the cavity for maximum response as indicated on the analyzer. 2. INSERTION LOSS ADJUSTMENT A. Adjust the signal generator to the desired pass frequency at 0 dBm output. B. Loosen the three retaining screws around the loop connector. Rotate the loop until the analyzer indicates the desired insertion loss, and balanced return loss. Tighten the retaining screws, and repeat Step 1. TUNING SHAFT LOCK NUT LOOP CONNECTORS 310 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-8009 Rev. 1/05 TECHNICAL NOTES PASS-REJECT CAVITY AND DUPLEXER TUNING 8 IMPORTANT: All cavities and cavity-based devices are factory tuned to the exact frequencies indicated on the label. No further tuning or optimization is necessary. If frequency or insertion loss must be changed, Telewave recommends that the equipment be returned to the factory to ensure optimum performance. The instructions in this document are for use only if factory service is not practical. TEST EQUIPMENT MINIMUM REQUIREMENTS: 1. Calibrated RF signal generator with 0 dBm output. 2. Calibrated frequency counter or meter. 3. Calibrated RF indicator such as a network analyzer or spectrum analyzer, with sensitivity of at least 80 dB below the RF generator output. Tools required: 7/16" wrench and nut-driver, medium and small flat-blade screwdrivers. NOTE: When transmitter power is passing through a cavity, high RF voltages and currents exist on the internal surfaces. Cavity tuning should be performed using a signal generator only. If no other RF source is available, use the lowest output power available and make only minimal adjustments. 1. TUNING THE PASS FREQUENCY A. Adjust the signal generator to the desired pass frequency at 0 dBm output. B. Connect the signal generator to one side of the cavity "T" connector, and the monitor or analyzer to the other side. C. Loosen the 7/16" locking nut on the center tuning shaft, and tune the shaft of the cavity for maximum response as indicated on the analyzer. TUNING SHAFT "T" CONNECTOR 2. TUNING THE REJECT FREQUENCY A. Adjust the signal generator to the desired reject frequency at 0 dBm output. B. Connect the signal generator to one side of the cavity "T" connector, and the monitor or analyzer to the other side. C. Tune the capacitor for maximum attenuation of the output signal, as indicated on the analyzer. LOCK NUT CAPACITOR LOOP CONNECTOR Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-8008 Rev. 3/07 311 PASS-REJECT CAVITY AND DUPLEXER TUNING 3. INSERTION LOSS ADJUSTMENT A. Adjust the signal generator to the desired pass frequency at 0 dBm output. B. Loosen the three retaining screws around the loop connector. Rotate the loop until the analyzer indicates the desired insertion loss. Tighten the retaining screws, and repeat Steps 1 and 2. An increase in the insertion loss will also increase the attenuation at the reject frequency. Minimum insertion loss occurs when the capacitor is on the opposite side of the connector, away from the center tuning rod. NOTE: All tuning adjustments are mutually dependent. This means that when you adjust the capacitor, the insertion loss will change and the loop position may have to be readjusted. The center tuning may have changed as well. Multiple adjustments will be required to achieve the best performance. 4. PASS-REJECT DUPLEXER TUNING PROCEDURE A. Examine the labels on the top of the duplexer, and locate the TX and RX ports. The cavity set for TX will be PASS-TX and REJECT-RX. The cavity set for RX will be PASS-RX and REJECT-TX. If TX and RX are not marked, then you must determine which port is connected to the lower frequency device, and which is connected to the higher frequency device. The cavity set for the low frequency device will be PASS-LOW and REJECT-HIGH. The cavity set for the high frequency device will be PASS-HIGH and REJECT-LOW. B. Tune one cavity at a time using Steps 1-3. The reject frequency of one set of cavities is always tuned to the pass frequency of the other set. RECEIVER Tune rejection on these cavities to TX frequency ANTENNA TRANSMITTER Tune rejection on these cavities to RX frequency 312 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice TWDS-8008 Rev. 3/07 TECHNICAL NOTES VSWR / RETURN LOSS CHART 8 VSWR · Return Loss · Transmitted Power % · Reflected Power % VSWR 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17 1.18 1.19 1.20 1.21 1.22 1.23 1.24 1.25 1.26 1.27 1.28 1.29 1.30 1.32 1.34 1.36 1.38 1.40 1.42 1.44 1.46 1.48 1.50 1.52 1.54 1.56 1.58 1.60 1.62 VSWR (dB) 0.00 0.10 0.20 0.30 0.30 0.40 0.50 0.60 0.70 0.70 0.80 0.90 1.00 1.10 1.10 1.20 1.30 1.40 1.40 1.50 1.60 1.70 1.70 1.80 1.90 1.90 2.00 2.10 2.10 2.20 2.30 2.40 2.50 2.70 2.80 2.90 3.00 3.20 3.30 3.40 3.50 3.60 3.80 3.90 4.00 4.10 4.20 RETURN LOSS (dB) 46.10 40.10 36.60 34.20 32.30 30.70 29.40 28.30 27.30 26.40 25.70 24.90 24.30 23.70 23.10 22.60 22.10 21.70 21.20 20.80 20.40 20.10 19.70 19.40 19.10 18.80 18.50 18.20 17.90 17.70 17.20 16.80 16.30 15.90 15.60 15.20 14.90 14.60 14.30 14.00 13.70 13.40 13.20 13.00 12.70 12.50 TRANS. LOSS (dB) 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.01 0.01 0.01 0.01 0.01 0.01 0.02 0.02 0.02 0.02 0.03 0.03 0.03 0.04 0.04 0.04 0.05 0.05 0.05 0.06 0.06 0.07 0.07 0.08 0.08 0.09 0.10 0.11 0.12 0.13 0.14 0.16 0.17 0.18 0.19 0.20 0.21 0.23 0.24 0.25 VOLT. REFL. COEFF. 0.00 0.00 0.01 0.01 0.02 0.02 0.03 0.03 0.04 0.04 0.05 0.05 0.06 0.06 0.07 0.07 0.07 0.08 0.08 0.09 0.09 0.10 0.10 0.10 0.11 0.11 0.12 0.12 0.12 0.13 0.13 0.14 0.15 0.15 0.16 0.17 0.17 0.18 0.19 0.19 0.20 0.21 0.21 0.22 0.22 0.23 0.24 POWER TRANS. (%) 100.00 100.00 100.00 100.00 100.00 99.90 99.90 99.90 99.90 99.80 99.80 99.70 99.70 99.60 99.60 99.50 99.50 99.40 99.30 99.20 99.20 99.10 99.00 98.90 98.90 98.80 98.70 98.60 98.50 98.40 98.30 98.10 97.90 97.70 97.50 97.20 97.00 96.70 96.50 96.30 96.00 95.70 95.50 95.20 94.90 94.70 94.40 POWER REFL. (%) 0.00 0.00 0.00 0.00 0.00 0.10 0.10 0.10 0.10 0.20 0.20 0.30 0.30 0.40 0.40 0.50 0.50 0.60 0.70 0.80 0.80 0.90 1.00 1.10 1.10 1.20 1.30 1.40 1.50 1.60 1.70 1.90 2.10 2.30 2.50 2.80 3.00 3.30 3.50 3.70 4.00 4.30 4.50 4.80 5.10 5.30 5.60 VSWR 1.64 1.66 1.68 1.70 1.72 1.74 1.76 1.78 1.80 1.82 1.84 1.86 1.88 1.90 1.92 1.94 1.96 1.98 2.00 2.50 3.00 3.50 4.00 4.50 5.00 5.50 6.00 6.50 7.00 7.50 8.00 8.50 9.00 9.50 10.00 11.00 12.00 13.00 14.00 15.00 16.00 17.00 18.00 19.00 20.00 25.00 30.00 VSWR (dB) 4.30 4.40 4.50 4.60 4.70 4.80 4.90 5.00 5.10 5.20 5.30 5.40 5.50 5.60 5.70 5.80 5.80 5.90 6.00 8.00 9.50 10.90 12.00 13.10 14.00 14.80 15.60 16.30 16.90 17.50 18.10 18.60 19.10 19.60 20.00 20.80 21.60 22.30 22.90 23.50 24.10 24.60 25.10 25.60 26.00 28.00 29.50 RETURN LOSS (dB) 12.30 12.10 11.90 11.70 11.50 11.40 11.20 11.00 10.90 10.70 10.60 10.40 10.30 10.20 10.00 9.90 9.80 9.70 9.50 7.40 6.00 5.10 4.40 3.90 3.50 3.20 2.90 2.70 2.50 2.30 2.20 2.10 1.90 1.80 1.70 1.60 1.50 1.30 1.20 1.20 1.10 1.00 1.00 0.90 0.90 0.70 0.60 TRANS. LOSS (dB) 0.26 0.28 0.29 0.30 0.32 0.33 0.34 0.36 0.37 0.38 0.40 0.41 0.43 0.44 0.45 0.47 0.48 0.50 0.51 0.88 1.25 1.60 1.94 2.26 2.55 2.83 3.10 3.35 3.59 3.82 4.03 4.24 4.44 4.63 4.81 5.15 5.47 5.76 6.04 6.30 6.55 6.78 7.00 7.21 7.41 8.30 9.04 VOLT. REFL. COEFF. 0.24 0.25 0.25 0.26 0.26 0.27 0.28 0.28 0.29 0.29 0.30 0.30 0.31 0.31 0.32 0.32 0.32 0.33 0.33 0.43 0.50 0.56 0.60 0.64 0.67 0.69 0.71 0.73 0.75 0.76 0.78 0.79 0.80 0.81 0.82 0.83 0.85 0.86 0.87 0.88 0.88 0.89 0.89 0.90 0.90 0.92 0.94 POWER TRANS. (%) 94.10 93.80 93.60 93.30 93.00 92.70 92.40 92.10 91.80 91.50 91.30 91.00 90.70 90.40 90.10 89.80 89.50 89.20 88.90 81.60 75.00 69.10 64.00 59.50 55.60 52.10 49.00 46.20 43.70 41.50 39.50 37.70 36.00 34.50 33.10 30.60 28.40 26.50 24.90 23.40 22.10 21.00 19.90 19.00 18.10 14.80 12.50 POWER REFL. (%) 5.90 6.20 6.40 6.70 7.00 7.30 7.60 7.90 8.20 8.50 8.70 9.00 9.30 9.60 9.90 10.20 10.50 10.80 11.10 18.40 25.00 30.90 36.00 40.50 44.40 47.90 51.00 53.80 56.20 58.50 60.50 62.30 64.00 65.50 66.90 69.40 71.60 73.50 75.10 76.60 77.90 79.00 80.10 81.00 81.90 85.20 87.50 Telewave, Inc. · San Jose, CA · 1-800-331-3396 ~ 408-929-4400 · www.telewave.com All specifications subject to change without notice 313 INDEX 1 TRANSMITTER COMBINING LOWBAND COMBINERS M104-150-4TPC M108-150-TRM M101-150-8TRM19 M101-150-8TRM M106-450-4, 8TPC M107-250, 350, 450, TP M107-250, 350, 450, TRM M108-450-10TRM M108-450-8TRM3Q M101-450-8TRM19-3Q M101-450-8TRM M108-760-10TRM M106-860-5TP, 10TP M107-860-5TRM-HP, 10TRM-HP M101-860-10TRM TC860 TW860-2HRB1N, 4HRB1N M108-900-10TRM3Q M101-900-10TRMH BANDPASS/NOTCH COMBINERS HYBRID COMBINERS FREQ. (MHz) 30-88 148-170 148-174 148-174 148-174 400-512 200-512 200-512 400-512 400-512 400-512 406-512 746-869 851-869 851-869 806-869 851-869 851-869 896-941 896-941 66-512 118-960 DESCRIPTION LOWBAND LOW LOSS COMBINERS . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 CHANNEL LOW LOSS COMBINER . . . . . . . . . . . . . . . . . . . . . . . . . 7 8 TO 10 CHANNEL LOW LOSS COMBINER . . . . . . . . . . . . . . . . . . . . 8 LOW LOSS VHF COMBINER FOR CLOSE SPACING . . . . . . . . . . . . . 9 LOW LOSS VHF COMBINER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 COMPACT TRANSMITTER COMBINER PANELS. . . . . . . . . . . . . . . 11 LOW LOSS TRANSMITTER COMBINER PANELS. . . . . . . . . . . . . . . 12 EXPANDABLE TRUNKING COMBINERS . . . . . . . . . . . . . . . . . . . . . 13 UHF TRUNKING TRANSMITTER COMBINER . . . . . . . . . . . . . . . . . 14 LOW LOSS UHF TRUNKING COMBINER . . . . . . . . . . . . . . . . . . . . . 15 LOW LOSS UHF COMBINER FOR CLOSE SPACING . . . . . . . . . . . . 16 LOW LOSS UHF COMBINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 LOW LOSS 760/860 MHz TRUNKING COMBINER . . . . . . . . . . . . . 18 COMPACT TRUNKING COMBINER PANELS. . . . . . . . . . . . . . . . . . 19 COMPACT TRUNKING COMBINER 175 WATTS . . . . . . . . . . . . . . . 20 LOW LOSS 800/900 MHz TRUNKING COMBINER . . . . . . . . . . . . . 21 CERAMIC ENHANCED TRUNKING COMBINER . . . . . . . . . . . . . . . 22 COMPACT HYBRID COMBINERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 LOW LOSS 900 MHz TRUNKING COMBINER . . . . . . . . . . . . . . . . . 24 900 MHz HYBRID TRUNKING COMBINER. . . . . . . . . . . . . . . . . . . . 25 1 NOTCH, 1-3 PASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2 AND 4 CHANNEL HYBRID COMBINERS. . . . . . . . . . . . . . . . . . . . 27 2 RECEIVER MULTICOUPLERS TWR2, TWR4 PANELS TWR8 / 16 / 24 STD PANELS TWR8 / 16 -1R COMPACT PANELS TWR24 / 32 -2R PANELS PS- SERIES TLA SERIES TGA SERIES TWR1 SERIES TOWER TOP PREAMPLIFIERS TTPA-4544 TTPA-8626, 8644, 8648 TTBS-4586 TPCP-1342C, TPCP-1343C TPCP-1344C, TPCP-1344CM TPCP-1442C, TPCP-1443C TPCP-1444C, TPCP-1444CM TPCP-1446C TPCP-1414, 1514, 1614, 1714 TPCP-1542C, TPCP-1543C TPCP-1544C, TPCP-1544CM TPCP-1546C TPCP-1554, 1556 TPCP-2244, 2246 TPCP-3544, 3546, 3548 TPCP-4542 TPCP-4544, 4546, 4548 TPCP-45215, 46215, 45215-2 TPCP-4514 TPCP-8642, TPCP-8644 TTPP-8642 TPCP-8626, TPCF-8926 3 POWER MONITORING MODEL 44L1, L1P MODEL 44A, AP PM-1A, 2A SERIES PM1C1S PM5C1S PM10C2S1C FREQ. (MHz) 132-960 30-960 30-960 30-960 10-1000 30-960 132-960 132-960 300-901 455-512 806-960 118-136 118-136 135-151 135-151 135-151 140-180 148-174 148-174 148-174 148-174 200-300 300-400 400-512 400-512 450-470 450-470 806-960 806-960 806-890 FREQ. (MHz) 2-200 20-1000 30-960 30-960 30-960 30-960 DESCRIPTION RECEIVER DISTRIBUTION PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . 30 RECEIVER DISTRIBUTION PANELS . . . . . . . . . . . . . . . . . . . . . . . . . . 31 COMPACT RECEIVER PANELS - 8-16 CHANNELS. . . . . . . . . . . . . . 33 COMPACT RECEIVER PANELS - 24-32 CHANNELS . . . . . . . . . . . . 35 RECEIVER POWER SPLITTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 LOW NOISE BIPOLAR INLINE PREAMPLIFIERS. . . . . . . . . . . . . . . . 38 PHEMT PREAMPLIFIERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 BROADBAND RACK MOUNT PREAMPLIFIERS. . . . . . . . . . . . . . . . 40 TOWER TOP PREAMPLIFIERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 TOWERTOP PREAMPLIFIER / PRESELECTOR . . . . . . . . . . . . . . . . . 42 TOWER TOP PREAMPS AND BASE UNIT . . . . . . . . . . . . . . . . . . . . 43 TOWER TOP BASE POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . 44 COMPACT AIRBAND PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . 45 COMPACT AIRBAND PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . . . 46 COMPACT BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . 47 COMPACT BANDPASS PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . 48 COMPACT BANDPASS PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . 49 COMPACT BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . 50 COMPACT BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . 51 COMPACT BANDPASS PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . 52 COMPACT BANDPASS PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . 53 BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 BANDPASS PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 COMPACT BANDPASS PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . 60 BANDPASS PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 BANDPASS PRESELECTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 COMBLINE PRESELECTORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 DESCRIPTION BROADBAND RF WATTMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 BROADBAND RF WATTMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 RF POWER MONITORS - SINGLE, DUAL . . . . . . . . . . . . . . . . . . . . . 70 RF WATTMETER / ALARM PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . 71 RF WATTMETER / ALARM PANEL. . . . . . . . . . . . . . . . . . . . . . . . . . . 72 RF WATTMETER PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 4 ISOLATORS & LOADS TWL-01, 35, 60 TWL-50, 75, 100, 100HS TWL-150, TWL-300 T-1030, 1060 T-1530, 1560 T-1530M, 1560M T-2230, 2260 T-3530, 3560 T-4530, 4560 T-7530, 7560 T-8630, 8660 HIGH POWER ISOLATORS TS150, 450, 900 SERIES THRP - REPEATER PANEL 5 CAVITIES & FILTERS TWPC-0310, 0410 TWPC-0412-1, TWNC-0412-1 TWPC-1005-1,2 TWPC-1008-1, 2 TPRC-1005-1, 2 TPRC-1008-1, 2 TWNC-1005-1, 2 TWNC-1008-1, 2 TWPC-1405-1, 2, 3 TWPC-1408-1, 2 TWPC-1410-1, 2 TPRC-1405-1,2 TWPC-1505-1, 2, 3 TWPC-1508-1, 2 TWPC-1510-1, 2 TPRC-1505-1, 2 TWNC-1505-1, 2 TWPC-2205-1, 2, 3 TWPC-2208-1, 2 TWPC-3505-1, 2, 3 TWPC-4504-1, 2, 3 TWPC-4505-1, 2, 3 TWPC-4510-1, 2 TWPC-7908-1, -2 TWPC-8608-1,2 TLF SERIES THF SERIES TWX-50, 150 6 DUPLEXERS TPRD-0354, 0454 TPRD-0384, 0484 TPRD-0754 TPRD-1084 TPRD-1344C, CM TPRD-1444C, CM TPRD-1446C TPRD-1454, 1456 TPRD-1484, 1486 TPRD-1544F TPRD-1543C TPRD-1544C, CM TPRD-1546C TPCD-1553, 1554, 1556 TPRD-1554, 1556 TPRD-1566 TPRD-1584, 1586 TPRD-2254 TPCD-4554, 4556 TPRD-4544, 4744 FREQ. (MHz) 0-2500 0-2500 0-2500 66-108 118-174 148-174 216-252 300-400 400-512 700-800 806-960 148-960 118-960 138-960 FREQ. (MHz) 30-50 40-50 88-108 88-108 88-108 88-108 88-108 88-108 118-148 118-148 118-148 118-148 148-174 148-174 148-174 148-174 148-174 200-300 200-300 300-400 400-512 400-512 400-512 776-825 800-970 40-960 40-960 50-150 FREQ. (MHz) 30-50 30-50 66-88 88-108 118-136 135-151 135-151 118-148 118-148 148-174 148-174 148-174 148-174 148-174 144-174 136-174 148-174 200-300 400-512 450-470 DESCRIPTION COAXIAL RF TERMINATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 COAXIAL RF TERMINATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 HIGH POWER TERMINATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 79 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 80 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 81 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 82 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 83 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 84 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 85 SINGLE / DUAL FERRITE ISOLATORS . . . . . . . . . . . . . . . . . . . . . . . . 86 SINGLE AND DUAL STAGE TO 400 WATTS. . . . . . . . . . . . . . . . . . . 87 INTERMOD SUPPRESSION PANELS . . . . . . . . . . . . . . . . . . . . . . . . . 88 HIGH PERFORMANCE REPEATER PANEL . . . . . . . . . . . . . . . . . . . . 89 DESCRIPTION BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 BANDPASS & NOTCH CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 PASS/REJECT CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 PASS/REJECT CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 NOTCH CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 NOTCH CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 PASS/REJECT CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 PASS/REJECT CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 NOTCH CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132 BANDPASS CAVITIES - ¾ WAVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 BANDPASS CAVITY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 BANDPASS CAVITIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 TRANSMITTER LOW PASS FILTERS. . . . . . . . . . . . . . . . . . . . . . . . . . 142 HIGH PASS FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 RECEIVER CRYSTAL FILTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 DESCRIPTION PASS / REJECT DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 PASS / REJECT DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148 PASS / REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 PASS / REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 COMPACT PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . 151 COMPACT PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . 152 COMPACT PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . 153 PASS/REJECT DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154 PASS/REJECT DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156 COMPACT PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . 157 COMPACT PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . 158 COMPACT PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . 159 COMPACT PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . 160 BANDPASS DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161 PASS/REJECT DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 PASS/REJECT DUPLEXER - DUAL NOTCH. . . . . . . . . . . . . . . . . . . . 165 PASS/REJECT DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167 PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 BANDPASS DUPLEXERS - ¾-WAVE . . . . . . . . . . . . . . . . . . . . . . . . . 169 PASS-REJECT DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 TPRD-4546 TPRD-4554, 4556 TTPD-7644 TTPD-8642, 8644 TPRD-8644 TPRD-9044 TPRD-12044 TPCD-8626 TPCD-8626HP TMND-0716, 0816 TMND-1516, 1616, 1716 TMND-4416, 4516, 4616 TMND-4716, 4816, 4916, 5016 TMND-7616 TMND-8616 400-512 400-512 763-869 806-960 763-869 890-960 1240-1300 806-960 806-960 70-85 148-174 440-470 470-512 769-805 860-870 7 ANTENNAS FREQ. (MHz) COLLINEAR ANTENNAS ANT125F2 118-136 ANT135F2 125-150 ANT140F2 135-165 ANT150F2 148-174 ANT150F6 138-175 ANT195F2 174-216 ANT220F2 195-260 ANT220F6 216-225 ANT355F6 340-370 ANT385F6 370-400 ANT400F2 360-455 ANT415F6 405-440 ANT415F8 395-436 ANT425F2 380-470 ANT450F2 420-480 ANT450F6 445-480 ANT450F10 430-475 ANT480F2 450-512 ANT500F6 470-512 ANT500F10 470-512 ANT734-960F2 734-960 ANT770F2 734-806 ANT770F6 746-806 ANT825F6 745-860 ANT850F2 806-896 ANT850F6 806-896 ANT850F10 806-896 ANT900F2 880-960 ANT940F6 870-965 ANT940F10 870-965 ANT960F0 900-960 F2 COLLINEAR INSTALLATION F6/8/10 COLLINEAR INSTALLATION ANTC482 CLAMP INSTALLATION ANTC483 CLAMP INSTALLATION DIPOLE ANTENNAS ANT37D ANT40D ANT42D ANT44D ANT50D ANT70D ANT75D ANT90D ANT120D, D3 ANT150D, D3, D6-9 ANT150D7-12 ANT220D, D3, D6-9 33.5-41 37.5-44.5 38.5-47 41.5-48 45-54 63-78 66-88 88-108 110-138 138-174 138-174 216-252 PASS-REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 173 BANDPASS/REJECT DUPLEXERS - ¾-WAVE . . . . . . . . . . . . . . . . . . 175 BANDPASS/REJECT DUPLEXER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 BANDPASS/REJECT DUPLEXER . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 PASS/REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183 PASS-REJECT DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 COMBLINE DUPLEXER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 HIGH POWER COMBLINE DUPLEXER . . . . . . . . . . . . . . . . . . . . . . . 188 MID-BAND MOBILE DUPLEXERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 190 MOBILE DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 MOBILE DUPLEXERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 COMPACT MOBILE DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 COMPACT MOBILE DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 COMPACT MOBILE DUPLEXER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 199 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 200 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 201 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 202 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 203 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 204 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 205 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 206 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 207 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 208 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 209 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 210 FIBERGLASS COLLINEAR ANTENNA 8 dBd . . . . . . . . . . . . . . . . . . 211 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 212 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 213 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 214 FIBERGLASS COLLINEAR ANTENNA 10 dBd . . . . . . . . . . . . . . . . . 215 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 216 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 217 FIBERGLASS COLLINEAR ANTENNA 10 dBd . . . . . . . . . . . . . . . . . 218 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 219 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 220 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 221 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 222 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 223 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 224 FIBERGLASS COLLINEAR ANTENNA 10 dBd . . . . . . . . . . . . . . . . . 225 FIBERGLASS COLLINEAR ANTENNA 2.5 dBd. . . . . . . . . . . . . . . . . 226 FIBERGLASS COLLINEAR ANTENNA 6 dBd . . . . . . . . . . . . . . . . . . 227 FIBERGLASS COLLINEAR ANTENNA 10 dBd . . . . . . . . . . . . . . . . . 228 WIRELESS DATA ANTENNA 2 dBd. . . . . . . . . . . . . . . . . . . . . . . . . . 229 INSTALLATION F2 ANTENNAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 INSTALLATION F6-F8-F10 ANTENNAS . . . . . . . . . . . . . . . . . . . . . . 231 ANTC482 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 ANTC483 / 483SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234 SINGLE DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235 SINGLE DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 236 SINGLE DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 237 SINGLE DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 SINGLE DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 SINGLE DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240 SINGLE DIPOLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241 SINGLE DIPOLE FM BROADCAST . . . . . . . . . . . . . . . . . . . . . . . . . . 242 SINGLE AND DIPOLE ARRAY 1 TO 6 dBd . . . . . . . . . . . . . . . . . . . . 243 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 244 DIPOLE AND DIPOLE ARRAY 7 TO 12 dBd . . . . . . . . . . . . . . . . . . . 245 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 246 ANT275D, D3, D6-9 ANT350D, D3, D6-9 ANT375D, D3, D6-9 ANT400D, D3, D6-9 ANT425D, D3, D6-9 ANT450D, D3, D6-9 ANT450D7-12 ANT500D, D3, D6-9 ANT750D, D3, D6-9 ANT900D, D3, D6-9 DIPOLE MOUNTING DIPOLE PATTERN ADJUST DIPOLE PATTERN ADJUST 230-330 300-360 345-405 360-450 380-470 406-512 406-512 470-550 700-825 800-1000 30-300 300-1000 YAGI ANTENNAS ANT144Y5-WR ANT150Y7-WR ANT150Y10H ANT220Y7-WR ANT390Y5-WR ANT410Y10-WR ANT420Y10-WR ANT430Y10-WR ANT440Y10-WR ANT450Y5-WR ANT450Y7-WR ANT450Y10-WR ANT475Y5-WR ANT490Y10-WR ANT500Y10-WR ANT740Y8-WR ANT750Y5-WR ANT830Y10-WR ANT850Y10-WR ANT930Y10-WR ANT930Y12-WR ANT1470Y12-WR ANT1800Y10-WR ANT1920Y9-WR ANT1920Y12-WR ANT2045Y12-WR ANT2350Y12-WR ANT2400Y12-WR ANT2600Y12-WR YAGI INSTALLATION SHEET YAGI INSTALLATION SHEET 138-152 148-174 144-174 216-240 370-410 405-420 415-450 420-440 438-455 420-470 450-470 450-470 450-512 470-500 485-512 698-787 734-806 800-870 824-896 885-975 880-960 1425-1535 1710-1880 1850-1990 1850-1990 1920-2170 2300-2500 2400-2500 2500-2700 138-960 1000-2700 WIDEBAND ANTENNAS ANT220K ANT260K, KT ANT280S ANT400K, KS ANT500WR 30-3000 75-3000 118-3000 400-3000 500-3000 MOUNTING HARDWARE ANTENNA CONNECTION SEALING ANTPD 204, 206 ANTPD SERIES TS-1546, TS-1580, TS-4680 24-72 24-2500 132-960 8 TECHNICAL NOTES SINGLE ISOLATOR TUNING DUAL ISOLATOR TUNING PASS CAVITY TUNING PASS-REJECT CAVITY/DUPLEXER TUNING VSWR / RETURN LOSS CHART DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 247 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 248 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 249 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 250 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 251 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 252 DIPOLE AND DIPOLE ARRAY 7 TO 12 dBd . . . . . . . . . . . . . . . . . . . 253 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 254 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 255 DIPOLE AND DIPOLE ARRAY 1 TO 9 dBd . . . . . . . . . . . . . . . . . . . . 256 DIPOLE MOUNTING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . 257 DIPOLE PATTERN ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 258 DIPOLE PATTERN ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262 YAGI ANTENNA 5 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 YAGI ANTENNA 5 dBd / 7 dBi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 YAGI ANTENNA 5 dBd / 7 dBi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 YAGI ANTENNA 5 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 267 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 YAGI ANTENNA 5 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 YAGI ANTENNA 7 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274 YAGI ANTENNA 5 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 277 YAGI ANTENNA 8 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278 YAGI ANTENNA 5 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280 YAGI ANTENNA 10 dBd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281 YAGI ANTENNA 10.2 dBd / 12.3 dBi . . . . . . . . . . . . . . . . . . . . . . . . . 282 YAGI ANTENNA 12.2 dBd / 14.3 dBi . . . . . . . . . . . . . . . . . . . . . . . . . 283 YAGI ANTENNA 12.2 dBd / 14.3 dBi . . . . . . . . . . . . . . . . . . . . . . . . . 284 YAGI ANTENNA 10.2 dBd / 12.3 dBi . . . . . . . . . . . . . . . . . . . . . . . . . 285 YAGI ANTENNA 9.3 dBd / 11.4 dBi . . . . . . . . . . . . . . . . . . . . . . . . . . 286 YAGI ANTENNA 12.2 dBd / 14.3 dBi . . . . . . . . . . . . . . . . . . . . . . . . . 287 YAGI ANTENNA 12 dBd / 14.1 dBi. . . . . . . . . . . . . . . . . . . . . . . . . . . 288 YAGI ANTENNA 12 dBd / 14.1 dBi. . . . . . . . . . . . . . . . . . . . . . . . . . . 289 YAGI ANTENNA 12 dBd / 14.1 dBi. . . . . . . . . . . . . . . . . . . . . . . . . . . 290 YAGI ANTENNA 12 dBd / 14.1 dBi. . . . . . . . . . . . . . . . . . . . . . . . . . . 291 INSTALLATION FOR YAGI ANTENNAS . . . . . . . . . . . . . . . . . . . . . . 292 INSTALLATION FOR YAGI ANTENNAS . . . . . . . . . . . . . . . . . . . . . . 293 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 WIDEBAND DISCONE ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . 295 WIDEBAND DISCONE ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . 296 WIDEBAND DISCONE ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . 297 WIDEBAND DISCONE ANTENNA . . . . . . . . . . . . . . . . . . . . . . . . . . 298 WIDEBAND DIRECTIONAL ANTENNA . . . . . . . . . . . . . . . . . . . . . . 299 ANTENNA MOUNTING HARDWARE. . . . . . . . . . . . . . . . . . . . . . . . 300 ANTENNA CONNECTION WEATHERPROOFING . . . . . . . . . . . . . 301 LOW BAND RF POWER DIVIDERS . . . . . . . . . . . . . . . . . . . . . . . . . . 302 RF POWER DIVIDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 CROSSBAND COUPLERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305 DESCRIPTION SINGLE ISOLATOR TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308 DUAL ISOLATOR TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 309 PASS CAVITY TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310 P-R CAVITY/DUPLEXER TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 VSWR / RETURN LOSS CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313 Product Warranty / Terms of Sale Products sold by Telewave, Inc. (Seller) and covered by this Warranty are warranted to be free from defects in material and workmanship at the time of and for the period specified below after delivery to the Buyer. Seller's entire warranty obligation is limited to making adjustments by repair, replacement, or refunding the purchase price of any product which is returned to the Seller as provided below within the specified period from the date of shipment by the Seller. In no event shall Seller be liable for direct, special, or consequential damages for breach of warranty. Warranty periods: Antennas and mounting hardware - 5 years All other products - 1 year Adjustment will not be allowed for products which have been damaged by lightning, subjected to abuse, improper application or installation, alteration or accident, or negligence in use, storage, transportation or handling. Alteration or removal of the serial number or identification markings voids the Warranty. Seller shall have the right of final determination as to the existence and cause of a defect, whether adjustment will be allowed, and if allowed, whether adjustment will be by repair, replacement, or refund. Where adjustment is not allowed, a charge of 5% of the original purchase price will be made to the Buyer to cover the Seller's cost of inspection and handling. Shipping and packaging instructions must be obtained from the Seller before products are returned for adjustment. The Buyer will pay for packing, transportation, and transit insurance costs for returned products. The Seller reserves the right to discontinue models at any time or change specifications, design, or price without notice and without incurring any obligation. Products will be returned to the Buyer with transportation cost collect. Subject to the provisions of its "Patent Indemnity" clause, the Seller also warrants that it has the right to sell its products, that the Buyer shall have and enjoy quite possession thereof as against any lawful claims existing at the time of the sale by the Seller, and that said products are free from any charge of encumbrance in favor of third persons existing at the time of sale by the Seller. The foregoing constitutes the Seller's entire warranty, express, implied or statutory with respect to its products and states the full extent of its liability for breach of Warranty and for damages, whether direct, special or consequential resulting form any such breach. No change whatsoever thereto shall be binding upon the seller unless made in writing and signed by a duly authorized representative of the Seller. RETURN / RMA PROCEDURE: Please contact Telewave via phone, fax, or email to discuss any product issues with a sales engineer. Many issues occur due to incorrect installation, misconfiguration or irregularities within an existing system, and these can often be resolved at no charge without return of products. 1. Contact Telewave for technical assistance at sales@telewave.com or 1-800-331-3396. 2. Telewave will transfer the call or email to the appropriate department. 3. If it is determined that the product(s) should be returned, the Telewave RMA Dept will ask customer to provide billing and return shipping addresses, product model and serial number (if applicable), date of purchase, and where item was purchased. 4. Customer ships product(s) back to Telewave at customer's expense: -- Write RMA number on the outside of the box(es) -- Include a description of the problem with the product(s) -- Ship via a trackable shipping method (UPS, Fedex, etc.) -- Retain proof of shipment and tracking information 5. Product(s) are received by Telewave and evaluated by the appropriate department. Customer is contacted by RMA department before any charges are incurred. 6. Telewave reserves the right to charge for parts, labor, and freight in the event that the issue is not covered under warranty. 7. Telewave will return original, repaired or replacement item at customer's expense unless covered by warranty. © 2014 Telewave, Inc. No portion of this document may be reproduced for any reason without express written permission. TELEWAVE, INC. TRANSMITTER COMBINERS · ANTENNAS · FILTERS · WATTMETERS · RF POWER MONITORS · COUPLERS · HIGH-Q CAVITIES · PREAMPLIFIERS · IM SUPPRESSION RECEIVER MULTICOUPLERS · PRESELECTORS · DUPLEXERS · ISOLATORS POWER DIVIDERS · RF TERMINATIONS · WIRELESS SYSTEM ENGINEERING Authorised Delear Australia - Sale@avw.com.au | www.avw.com.au New Zealand - Sales@avw.co.nz |www.avw.co.nz