Instructions. ● Select the desired Key Number. The arrow to the right marks the selection available. ● Make selections from each Table (I, II and IX) using the column below the...
SmartLine Technical Information STR800 SmartLine Remote Diaphragm Seals Specification 34-ST-03-88, October 2020 . Introduction . Part of the SmartLine family of products, the STR800 is a
STR82D-21CC1C0-AFCAA21BS-A-BHS-11C-B-11A0-F1,F5 | Honeywell | STR800 (DP, GP & AP) Remote Seals
SmartLine
Technical Information
STR800 SmartLine Remote Diaphragm Seals Specification 34-ST-03-88, October 2020
Introduction
Part of the SmartLine® family of products, the STR800 is a series of high performance pressure transmitters hydraulically matched and optimized with a complete set of remote diaphragm seals. Utilizing the same high performance sensor technology of the ST 800 product line Honeywell has optimized the mechanical and hydraulic designs in order to minimize the typical effects of temperature on remote seal systems. The SmartLine family is also fully tested and compliant with Experion® PKS providing the highest level of compatibility assurance and integration capabilities. SmartLine easily meets the most demanding application needs for pressure measurement applications.
Best in Class Features: · Accuracies of up to 0.0375% of span · Automatic static pressure & temperature compensation · Rangeability up to 100:1 · Multiple local display capabilities · External zero, span, & configuration capability · Polarity insensitive electrical connections · Comprehensive on-board diagnostic capabilities · Integral Dual Seal design for highest safety based on ANSI/NFPA 70-202 and ANSI/ISA 12.27.0 · World class overpressure protection · Full compliance to SIL 2/3 requirements. · Modular design characteristics · Available with additional 15-year warranty
Typical Diaphragm Seal applications · High Process Temperatures
· Viscous or Suspended Solids
· Highly Corrosive Process Materials
· Sanitary Applications
· Applications with Hydrogen Permeation Possibilities
· Level Applications with Maintenance Intensive Wet Legs
· Applications requiring remote Transmitter Mounting
· Tank Applications with Density or Interface Measurements
Figure 1 STR800 Remote Diaphragm Seal Unit
Communications/Output Options: · Honeywell Digitally Enhanced (DE) · HART ® (version 7.0) · FOUNDATIONTM Fieldbus
All transmitters are available with the above listed communications protocols.
Span & Range Limits:
Model
URL
"H2O (mbar)
STR82D
400 (1000)
Model
psid (bar)
STR83D
100 (7.0)
Model
psig (bar)
STR84G
500 (35.0)
STR87G
3000 (210)
Model
psia (bara)
STR84A
500 (35)
LRL "H2O (mbar) -400 (-1000)
psid (bar) -100 (-7.0) psig (bar) -14.7 (-1.0) -14.7 (-1.0) psig (bara)
0 (0)
Min Span "H2O (mbar)
4.0 (10) psid (bar)
1 (0.07) psig (bar)
5 (0.35) 30 (2.1) psig (bara) 5 (0.35)
2
STR800 Smart Pressure Transmitter
Description
The SmartLine family of gauge pressure, differential pressure, and absolute pressure transmitters is designed around a high performance piezo-resistive sensor. This one sensor actually integrates multiple sensors linking process pressure measurement with on-board static pressure (DP Models) and temperature compensation measurements resulting in the best total performance available. This level of performance allows the ST 800 to replace virtually any competitive transmitter available today.
Unique Indication/Display Options The ST 800 modular design accommodates a basic alphanumeric LCD display or a unique advanced graphics LCD display with many unparalleled features.
Basic Alphanumeric LCD Display Features
· Modular (may be added or removed in the field) · 0, 90,180, & 270 degree position adjustments · Configurable (HART only) and standard (Pa, KPa,
MPa, KGcm2, Torr, ATM, inH2O, mH2O, bar, mbar, inH2O, inHG, FTH2O, mmH2O, mm HG, & psi) measurement units · 2 Lines 16 Characters (4.13H x 1.83W mm) · Square root output indication ()
Advanced Graphics LCD Display Features
· Modular (may be added or removed in the field) · 0, 90, 180, & 270 degree position adjustments · Standard and custom measurement units available. · Up to eight display screens with 3 formats are
possible · (Large PV with Bar Graph or PV with Trend Graph) · Configurable screen rotation timing · Display Square Root capabilities may be set
separately from the 4-20mA dc output signal · Unique "Health Watch" indication provides instant
visibility of diagnostics · Multiple language capability. (EN, DE, FR, IT, ES,
RU, TR, CN, JP)
Diagnostics SmartLine transmitters all offer digitally accessible diagnostics which aid in providing advanced warning of possible failure events minimizing unplanned shutdowns, providing lower overall operational costs
Configuration Tools Integral Three Button Configuration Option Suitable for all electrical and environmental requirements, SmartLine offer the ability to configure the transmitter and display via three externally accessible buttons when either display option is selected. Zero/span capabilities are also optionally available via these buttons with or without selection of a display option.
Hand Held Configuration SmartLine transmitters feature two-way communication and configuration capability between the operator and the transmitter. All Honeywell transmitters are designed and tested for compliance with the offered communication protocols and are designed to operate with any Standards compliant handheld configuration device.
Personal Computer Configuration Honeywell's SCT 3000 Configuration Toolkit provides an easy way to configure Digitally Enhanced (DE) instruments using a personal computer as the configuration interface. Field Device Manager (FDM) Software and FDM Express are also available for managing HART & Fieldbus device configurations.
System Integration o SmartLine communications protocols all meet the most
current published standards for HART/DE/Fieldbus. o Integration with Honeywell's Experion PKS offers the
following unique advantages. o Transmitter messaging o Maintenance mode indication o Tamper reporting o FDM Plant Area Views with Health summaries o All ST 800 units are Experion tested to provide the
highest level of compatibility assurance
Modular Design To help contain maintenance & inventory costs, all STR800 transmitters are modular in design supporting the user's ability to replace or add indicators, terminal connections or electronic modules without affecting overall performance or approval body certifications
Modular Features o Exchange/replace electronics/comms modules* o Add or remove integral indicators* o Add or remove lightning protection (terminal connection)*
* Field replaceable in all electrical environments (including IS) except flameproof without violating agency approvals.
With no performance effects, Honeywell's unique modularity results in lower inventory needs and lower overall operating costs.
STR800 Smart Pressure Transmitter
3
Performance Specifications
Reference Accuracy (conformance to +/-3 Sigma)
Model STR82D STR83D STR84G STR87G STR84A
URL
LRL
Min Span
400 in H2O (1000 mbar) 100 psid (7.0 bar) 500 psi (35 bar) 3000 psi (210 bar) 500 psia (35 bara)
-400 in H2O (-1000 mbar) -100 psi (-7.0 bar) -14.7 (-1.0 bar) -14.7 psi (-1.0 bar) 0 psia (0 bara)
4 in H2O (10 mbar) 1 in psi (0.07 bar)
5 psi (0.35 bar) 30 psi (2.1 bar) 5 psia (0.35 bara)
Maximum Turndown
Ratio
100:1 100:1 100:1 100:1 100:1
Reference Accuracy1,2
(% Span)
0.0375 0.0375 0.0375 0.0375 0.0375
Zero and span may be set anywhere within the listed (URL/LRL) range limits
Accuracy at Specified Span, Temperature and Static Pressure: (conformance to +/-3 Sigma)
Standard Accuracy
Accuracy1,2 (% of Span)
Model
STR82D STR83D STR84G STR87G STR84A
URL
400 in H2O (1000mbar) 100 psid (7.0 bar) 500 psi (35 bar) 3000 psi (210 bar) 500 psia (35 bara)
Reference A Turndown
C B (see URL
units)
8:1
3.33:1 25:1 10:1 25:1
0.005
0.0325
50 (125)
30 (2.1) 20 (1.4) 300 (2.1) 20 (1.4)
Turn Down Effect
Combined Zero & Span Temperature Effect3 (% Span/ 28oC (50oF))
F
D
E
(see URL
units)
0.175 0.025
1.000 0.280
200 (500) 30 (2.1)
Temp Effect
Total Performance (% of Span):
Total Performance = +/- ( Accuracy)2 + (Temp Effect)2
Total Performance Examples: (standard accuracy, 5:1 Turndown, up to 50 oF shift)
STR82D @ 80"H2O: 2.68% of span
STR83D @ 20 psid: 0.45% of span
Typical Calibration Frequency: Calibration verification is recommended every four (4) years
Notes:
1.Terminal Based Accuracy Includes combined effects of linearity, hysteresis, and repeatability. Analog output adds 0.005% of span. 2. For zero based spans and reference conditions of 25oC (77oF). 0 psi static pressure for DP, >= 0 psia for GP, 10 to 55% R.H, and 316 Stainless Steel barrier diaphragms
3. Specification applies to transmitter with 2 balanced remote seals. Apply a 1.5 factor for temperature effect for capillary lengths greater
than 10 feet.
4
STR800 Smart Pressure Transmitter
Operating Conditions All Models
Parameter
Reference Condition (at zero static)
Rated Condition
Operative Limits Transportation and Storage
Ambient Temperature1
°C
°F
°C
25±1
77±2
-
°F
°C
°F
°C
°F
-
-
-
-55 to 90 -67 to 194
Humidity
%RH
10 to 55
0 to 100
0 to 100
0 to 100
Vacuum Region, Minimum Pressure
mmHg absolute
Atmospheric (See Figure 4 for vacuum limitation)
Supply Voltage, Current, and Load Resistance
10.8 to 42.4 Vdc at terminals (IS versions limited to 30 Vdc) 0 to 1,440 ohms (as shown in Figure 2)
Maximum Allowable Working Pressure (MAWP)4
(ST 800 products are rated to Maximum Allowable Working Pressure. MAWP depends on Approval Agency and transmitter materials of construction.)
MAWP is minimum of Body Rating or Seal Rating (See Model Selection Guide for Seal
Body STR82D
MAWP 2,500 psig (172 bar) Bolted Process Heads
STR83D
2,500 psig (172 bar) Bolted Process Heads
STR82D
1,450 psig (100 bar) All Welded Process
STR83D
1,450 psig (100 bar) All Welded Process
STR84G
500 psig (35 bar)
STR87G
3,000 psig (207 bar)
STR84A
500 psia (35 bara)
1 Ambient Temperature Limit is a function of Process Interface Temperature and fill fluid. (See Figure 3 & Figure 4)
LCD Display operating temperature -20°C to +70°C . Storage temperature -30°C to 80°C 4 Consult factory for MAWP of ST 800 transmitters with CRN approval.
Figure 2 - Supply voltage and loop resistance
STR800 Smart Pressure Transmitter
5
Maximum Ambient Temperature (°F)
200
185
180
165
160
140
140
120
100
80
60
40
20
0
200
350
450
Process Interface Temperature (°F)
Figure 3 - Ambient temperature limits
Figure 4 - STR800 Remote Seals operable limits for pressure vs. temperature
6
STR800 Smart Pressure Transmitter
Performance Under Rated Conditions All Models
Parameter
Description
Analog Output
Two-wire, 4 to 20 mA (HART & DE Transmitters only)
Digital Communications:
Honeywell DE, HART 7 protocol or FOUNDATION Fieldbus ITK 6.0.1 compliant
All transmitters, irrespective of protocol have polarity insensitive connection.
HART & DE Output Failure Modes
(NAMUR for DE Units requires selecting display and configuration buttons or factory configuration)
Compliance: Normal Limits: Failure Mode:
Honeywell Standard:
3.8 20.8 mA 3.6 mA and 21.0 mA
NAMUR NE 43
3.8 20.5 mA 3.6 mA and 21.0 mA
Supply Voltage Effect
0.005% span per volt.
Transmitter Turn on Time (includes power up & test algorithms)
HART or DE: 2.5 sec.
Foundation Fieldbus: Host dependant
Damping Time Constant
HART: Adjustable from 0 to 32 seconds in 0.1 increments. Default: 0.50 seconds DE: Discrete values 0, .16, .32, .48, 1, 2, 4, 8, 16, 32 seconds. Default: 0.48 seconds
Electromagnetic Compatibility IEC 61326-3-1
Lightning Protection Option
Leakage Current: 10uA max @ 42.4VDC 93C
Impulse rating: 8/20uS
5000A (>10 strikes)
10/1000uS 200A (> 300 strikes)
10000A (1 strike min.)
Materials Specifications (see Model Selection Guide for availability/restrictions with various
models)
Parameter
Description
Process Interface
See Model Selection Guide for Material Options for desired seal type.
Seal Barrier Diaphragm 316L Stainless Steel, Monel®, Hastelloy® C, Tantalum
Seal Gasket Materials Klinger C-4401 (non-asbestos), Grafoil®, Teflon®, Gylon 3510®
Mounting Bracket
Carbon Steel (Zinc-Chromate plated) or 304 Stainless Steel or 316 Stainless Steel
Fill Fluid (Meter Body)
Silicone 200 CTFE (Chlorotrifluoroethylene) Silicone 704 NEOBEE M-20®
S.G. @ 25°C = 0.94 S.G. @ 25°C = 1.89 S.G. @ 25°C = 1.07 S.G. @ 25°C = 0.93
Fill Fluid (Secondary)
Silicone Oil 200
CTFE (Chlorotrifluoroethylene)
Silicone Oil 704 Syltherm 800® NEOBEE M-20®
S.G. @ 25°C = 0.94 S.G. @ 25°C = 1.89 S.G. @ 25°C = 1.07 S.G. @ 25°C = 0.90 S.G. @ 25°C = 0.93
Electronic Housing
Pure Polyester Powder Coated Low Copper (<0.4%)-Aluminum. Meets NEMA 4X, IP66, & P67. All stainless steel housing is optional.
Capillary Tubing
Material: Armored Stainless Steel or PVC Coated Armored Stainless Steel. Length: 5, 10, 15, 20, 25, and 35 feet (1.5, 3, 4.6, 6.1, 7.5, and 10.7 meters). A 2 inch (51 millimeter) S.S. close-coupled nipple is also available. See Model Selection Guide. Refer to Note: The minimum span is the higher of the higher of the value from the table above or the value defined under the Performance Conditions for the range transmitter.
Figure 5 for guide to maximum capillary length vs. diaphragm diameter.
Wiring
Accepts up to 16 AWG (1.5 mm diameter)
Mounting
See Figure 6
Dimensions
Transmitter: See Figure 7 and Figure 8. Seal: See Figure 9 through Figure 17
Net Weight
Transmitter: 8.3 pounds (3.8 Kg). With Aluminum Housing. Total weight is dependent on seal
NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or vessel(s) from exceeding allowable pressure limits, (equipment with safety functions in accordance with Pressure Equipment Directive 97/23/EC article 1, 2.1.3), require separate examination.
STR800 Smart Pressure Transmitter
7
Minimum recommended span for STR82D and STR83D Transmitter with two Remote Seals
Diaphragm
Capillary Length (Feet)
Size (Inches)
5
10
15
20
25
35
2.4
7.2 psi
2.9
3.6 psi
4.5 psi
5.4 psi
6.3 psi
3.5
0.6 psi
0.7 psi
0.9 psi
1.0 psi
1.2 psi 1.4 psi
4.1
0.4 psi
0.5 psi
0.6 psi
0.8 psi
0.9 psi 1.1 psi
Maximum Capillary Length (Feet)
5 20 35 35
Minimum recommended span for STR82D and STR83D Transmitter with one Remote Seal
Diaphragm Direct
Capillary Length (Feet)
Size (Inches) Mount
5
10
15
20
25
35
2.4
20 psi 30 psi
2.9
10 psi 15 psi 20 psi
25 psi
30 psi
3.5
1.8 psi 2.9 psi 3.6 psi 4.3 psi 5.0 psi 5.8 psi 7.2 psi
4.1
1.4 psi 2.2 psi 2.9 psi 3.6 psi 4.3 psi 5.0 psi 5.8 psi
Maximum Capillary Length (Feet)
5 20 35 35
Minimum recommended span for STR84G, STR84A and STR87G Transmitter
Diaphragm Direct
Size (Inches) Mount
5
Capillary Length (Feet)
10
15
20
25
Maximum Capillary
35
Length (Feet)
1.9
25 psi 30 psi 40 psi
50 psi
15
2.4
10 psi 15 psi 20 psi
25 psi
30 psi
35 psi
50 psi
35
2.9
8 psi
9 psi
10 psi
11 psi
12 psi
13 psi
15 psi
35
3.5
5 psi
5 psi
5 psi
5 psi
5 psi
6 psi
8 psi
35
4.1
5 psi
5 psi
5 psi
5 psi
5 psi
6 psi
8 psi
35
Note: The minimum span is the higher of the higher of the value from the table above or the value defined under the
Performance Conditions for the range transmitter.
Figure 5 Typical Maximum capillary length and diaphragm size chart
Figure 6 - STR800 transmitter with remote diaphragm seals shown mounted on a tank
8
Reference Dimensions Horizontal Mounting
STR800 Smart Pressure Transmitter
STR800 Smart Pressure Transmitter
9
Reference Dimensions Horizontal Mounting (cont'd)
Figure 7 -- Approximate horizontal mounting dimensions for Remote Seal Transmitter
Reference Dimensions Vertical Mounting
10
Reference Dimensions Vertical Mounting (cont'd)
STR800 Smart Pressure Transmitter
Figure 8 -- Approximate vertical mounting dimensions for Remote Seal Transmitter
STR800 Smart Pressure Transmitter
Reference Dimensions (cont'd)
Flush Flanged Seal Dimensions
11
Figure A Figure B
Figure C
Figure D
Figure 9-- Seal Dimensions (Flush Flanged)
12
Reference Dimensions (cont'd)
Flush Flanged Seal with Lower
STR800 Smart Pressure Transmitter
Flush Flanged Seal with Lower
Flush Flanged Seal with Lower
Nte: 0.90 dimension is 0.70 for 4.1" Dia Diaphragm
Figure 10 -- Seal Dimension (Flush Flanged)
STR800 Smart Pressure Transmitter
13
Reference Dimensions (cont'd)
Flanged Seal with Extended Diaphragm
Pancake Seal
Figure 11 -- Seal Dimensions (Extended Diaphragms)
Figure 12-- Seal Dimensions (Pancake) Chemical Tee "Taylor Wedge" Seal
Figure 13-- Seal Dimensions (Chemical TEE "Taylor Wedge" Seals
14 Seal with Threaded Process Connection
STR800 Smart Pressure Transmitter
Figure 14-- Seal Dimensions (Threaded Process Connection Seals) Sanitary Seal
Figure 15- Seal Dimensions (Sanitary Seals)
STR800 Smart Pressure Transmitter
15
Saddle Seal
Figure 16 -- Seal Dimensions (3" Saddle Seal)
Calibration Ring
Figure 17-- Seal Dimensions (4" Saddle Seal)
Figure 18-- Calibration Ring
16
Communications Protocols & Diagnostics
HART Protocol
Version:
HART 7
Power Supply Voltage: 10.8 to 42.4Vdc at terminals Load: Maximum 1440 ohms See Figure 2. Minimum Load: 0 ohms. (For handheld communications a minimum load of 250 ohms is required) Foundation Fieldbus (FF)
Power Supply Requirements Voltage: 9.0 to 32.0Vdc at terminals Steady State Current: 17.6mAdc Software Download Current: 27.4mAdc
Available Function Blocks
Block Type
Qty
Execution Time
Resource
1
n/a
Transducer
1
n/a
Diagnostic
1
Analog Input
1*
n/a 30 ms
PID w/Autotune
1
Integrator
1
45 ms 30 ms
Signal Char (SC)
1
LCD Display
1
30 ms n/a
Flow Block
1
Input Selector
1
30 ms 30 ms
Arithmetic
1
30 ms
* AI block may have two (2) additional instantiations.
All available function blocks adhere to FOUNDATION
Fieldbus standards. PID blocks support ideal & robust PID
algorithms with full implementation of Auto-tuning.
Link Active Scheduler Transmitters can perform as a backup Link Active Scheduler and take over when the host is disconnected. Acting as a LAS, the device ensures scheduled data transfers typically used for the regular, cyclic transfer of control loop data between devices on the Fieldbus.
Number of Devices/Segment Entity IS model: 6 devices/segment
Schedule Entries 18 maximum schedule entries Number of VCR's: 24 max Compliance Testing: Tested according to ITK 6.0.1
STR800 Smart Pressure Transmitter
Software Download Utilizes Class-3 of the Common Software Download procedure as per FF-883 which allows the field devices of any manufacturer to receive software upgrades from any host. Honeywell Digitally Enhanced (DE) DE is a Honeywell proprietary protocol which provides digital communications between Honeywell DE enabled field devices and Hosts. Power Supply Voltage: 10.8 to 42.4Vdc at terminals Load: Maximum 1440 ohms See Figure 2. Standard Diagnostics ST 800 top level diagnostics are reported as either critical or non-critical and readable via the DD/DTM tools or integral display as shown below.
Refer to ST 800 diagnostics tech note for additional level diagnostics. Other Certification Options Materials o NACE MRO175, MRO103, ISO15156
Hazardous Areal Certification:
MSG CODE
AGENCY
TYPE OF PROTECTION
COMM. ELECTRICAL AMBIENT TEMP
OPTION PARAMETERS
(Ta)
Explosionproof:
Class I, Division 1, Groups A, B, C, D;
Dust Ignition Proof:
Class II, III, Division 1, Groups E, F, G;
All
T6..T5
Class l, Zone 0/1, AEx db IIC T6..T5 Ga/Gb
Class ll, Zone 21, AEx tb IIIC T95o Db
Note 1
T5: -50 ºC to 85ºC T6: -50 ºC to 65ºC
Intrinsically Safe: Class I, II, III, Division 1, Groups A, B, C, D,
4-20 mA / DE/ HART
Note 2a
-50 ºC to 70ºC
E, F, G: T4
A
FM
Class l, Zone 0, AEx ia IIC T4 Ga
ApprovalsTM FISCO Field Device (Only for FF Option)
USA Ex ia IIC T4 Ga; Ex ic IIC T4 Gc
Foundation Fieldbus
Note 2b
-50 ºC to 70ºC
Nonincendive: Class I, Division 2, Groups A, B, C, D locations, T4 Class l, Zone 2, AEx nA IIC T4 Gc
4-20 mA / DE/ HART/ Foundation Fieldbus
Note 1
-50 ºC to 85ºC
Enclosure: Type 4X/ IP66/ IP67
All
All
-
STANDARDS: FM Class 3600:2011; FM Class 3610: 2010; FM Class 3611: 2004; FM Class 3615: 2006; FM Class 3616: 2011; FM Class 3810: 2005; ANSI/ISA 60079-0: 2013; ANSI/UL 60079-1: 2015; ANSI/UL 60079-11: 2014; ANSI/ISA 60079-15: 2012; ANSI/UL 60079-26: 2017; ANSI/UL 60079-31: 2015; ANSI/NEMA 250: 2003; ANSI/ IEC 60529: 2004
Explosion Proof: Class I, Division 1, Groups A, B, C, D; Class II, Division 1, Groups E, F, G; Class III, Division 1, T6..T5 Class I Zone 1 AEx db IIC T6..T5 Ga/Gb Ex db IIC T6..T5 Ga/Gb Zone 22 AEx tb IIIC T95o Db Ex tb IIIC T95o Db
All
Note 1
T5: -50oC TO 85oC T6: -50oC TO 65oC
Intrinsically Safe: Class I, II, III, Division 1, Groups A, B, C, D; Class II, Division 1, Groups E, F, G;
4-20 mA / DE/ HART
Note 2
Canadian Class III, Division 1, T4
Standards Class I Zone 0, AEx ia IIC T4 Ga
B
Association (CSA)
USA and Canada
Class I Zone 2, AEx ic IIC T4 Gc Ex ia IIC T4 Ga Ex ic IIC T4 Gc FISCO Field Device (Only for FF Option)
Foundation Fieldbus
Note 2
Ex ia IIC T4 Ga;
Ex ic IIC T4 Gc
-50oC TO 70oC -50oC TO 70oC
Nonincendive: Class I, Division 2, Groups A, B, C, D; Class II, Division 2, Groups F, G; Class III, Division 2, T4 Class I Zone 2 AEx nA IIC T4 Gc Ex nA IIC T4 Gc
4-20 mA / DE/ HART/ Foundation Fieldbus
Note 1
-50oC to 85oC
Enclosure: Type 4X/ IP66/ IP67
All
All
-
STANDARDS: CSA C22.2 No. 0-10; CSA C22.2 No. 94-M91; CSA C22.2 No. 25-1966; CSA C22.2
MSG CODE
C
D
AGENCY
ATEX
IECEx World
TYPE OF PROTECTION
COMM. ELECTRICAL AMBIENT TEMP
OPTION PARAMETERS
(Ta)
No. 30-M1986; CSA C22.2 No. 142-M1987; CSA C22.2 No. 157-92; CSA C22.2 No. 213-M1987; CSA-C22.2 No. 60529:05; CSA-C22.2 No. 60079-0:11; CSA-C22.2 No. 60079-1:11; CSA-C22.2 No. 60079-11:11; CSA-C22.2 No. 60079-15:12; CSA-C22.2 No. 60079-31:12; ISA 12.12.012010; ISA 60079-0: 2009; ISA 60079-11: 2011; ISA 60079-15: 2009; ISA 60079-26: 2008; ISA60079-27:2007 (12.02.04)-2006 (R2011); UL 913 Ed. 6; UL 916:1998; ANSI/ISA-12.27.01-2011
Flameproof: SIRA 12ATEX2233X II 1/2 G Ex db IIC T6..T5 Ga/Gb II 2 D Ex tb IIIC T95oC...T120oC Db
All
Note 1
T5: -50oC TO 85oC T6: -50oC TO 65oC
Intrinsically Safe: SIRA 12ATEX2233X II 1 G Ex ia IIC T4 Ga FISCO Field Device (Only for FF Option) II 1 G Ex ia IIC T4 Ga
4-20 mA / DE/ HART
Foundation Fieldbus
Note 2 Note 2
-50oC TO 70oC -50oC TO 70oC
Zone 2, Increase Safety: SIRA 12ATEX4234X II 3 G Ex ec IIC T4 Gc
4-20 mA / DE/ HART/
Note 1
-50oC TO 85oC
Zone 2, Intrinsically Safe: SIRA 12ATEX4234X II 3 G Ex ic IIC T4 Gc FISCO Field Device (Only for FF Option) II 3 G Ex ic IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 2
-50oC TO 85oC
Enclosure: IP66/ IP67
All
All
-
STANDARDS: EN 60079-0: 2012/A11: 2013; EN 60079-1: 2014; EN 60079-7: 2015; EN 6007911: 2012; EN 60079-26: 2015; EN 60079-31: 2009
Flameproof: IECEx SIR 12.0100X
Ex db IIC T6..T5 Ga/Gb Ex tb IIIC T95oC...T120oC Db
All
Note 1
T5: -50oC TO 85oC T6: -50oC TO 65oC
Intrinsically Safe: IECEx SIR 12.0100X Ex ia IIC T4 Ga FISCO Field Device (Only for FF Option) Ex ia IIC T4 Ga; Ex ic IIC T4 Gc
4-20 mA / DE/ HART
Foundation Fieldbus
Note 2 Note 2
-50oC TO 70oC -50oC TO 70oC
Zone 2, Increase Safety: IECEx SIR 12.0100X Ex ec IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 1
-50oC TO 85oC
Zone 2, Intrinsically Safe: IECEx SIR 12.0100X Ex ic IIC T4 Gc FISCO Field Device (Only for FF Option) Ex ic IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 2
-50oC TO 85oC
Enclosure: IP66/ IP67
All
All
-
STANDARDS: IEC 60079-0: 2011; IEC 60079-1: 2014; IEC 60079-7: 2017; IEC 60079-11: 2011; IEC 60079-26: 2014; IEC 60079-31: 2013
Flameproof : Ex d IIC T6...T5 Ga/Gb Ex tb IIIC T95oC...T120oC Db
All
Note 1
T5: -50oC TO 85oC T6: -50oC TO 65oC
Intrinsically Safe: Ex ia IIC Ga T4 FISCO Field Device (Only for FF Option) Ex ia IIC T4 Ga; Ex ic IIC T4 Gc
4-20 mA / DE/ HART
Foundation Fieldbus
Note 2 Note 2
E
SAEx
Zone 2, Increase Safety:
South Africa II 3 G Ex ec IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 1
-50oC TO 70oC -50oC TO 70oC -50oC TO 85oC
Zone 2, Intrinsically Safe: Ex ic IIC T4 Gc FISCO Field Device (Only for FF Option) Ex ic IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 2
-50oC TO 85oC
Enclosure: IP66/ IP67
All
All
-
Flameproof: Ex db IIC T6..T5 Ga/Gb Ex tb IIIC T95oC...T120oC Db
All
Note 1
T5: -50oC TO 85oC T6: -50oC TO 65oC
Intrinsically Safe: Ex ia IIC T4 Ga
4-20 mA / DE/ HART
Note 2a
-50oC TO 70oC
INMETRO
FISCO Field Device (Only for FF Option) Ex ia IIC T4 Ga; Ex ic IIC T4 Gc
Foundation Fieldbus
Note 2b
-50oC TO 70oC
F
Brazil
Zone 2, Increase Safety:
II 3 G Ex ec IIC T4 Gc
4-20 mA / DE/ HART/
Foundation
Note 1
-50oC TO 85oC
Fieldbus
Zone 2, Intrinsically Safe: Ex ic IIC T4 Gc FISCO Field Device (Only for FF Option) Ex ic IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 2
-50oC TO 85oC
Enclosure : IP 66/67
All
All
-
Flameproof:
Ex db IIC T6..T5 Ga/Gb Ex tb IIIC T 95oC Db
All
Note 1
T5: -50oC TO 85oC T6: -50oC TO 65oC
Intrinsically Safe: Ex ia IIC T4 Ga FISCO Field Device (Only for FF Option) Ex ia IIC T4 Ga; Ex ic IIC T4 Gc
4-20 mA / DE/ HART
Foundation Fieldbus
Note 2 Note 2
-50oC TO 70oC -50oC TO 70oC
G
NEPSI CHINA
Zone 2, Increase Safety: II 3 G Ex ec IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 1
-50oC TO 85oC
Zone 2, Intrinsically Safe: Ex ic IIC T4 Gc FISCO Field Device (Only for FF Option) Ex ic IIC T4 Gc
4-20 mA / DE/ HART/
Foundation Fieldbus
Note 2
-50oC TO 85oC
Enclosure : IP 66/67
All
All
-
Flameproof :
Ex d IIC T4, T5, T6
All
Ex tD A21 IP66/IP67 T95oC...T120 oC
H
KOSHA Korea
Intrinsically Safe:
Ex ia IIC T4
4-20 mA / DE/ HART
Foundation Fieldbus
Enclosure: IP66/ IP67
All
Flameproof:
Ga/Gb Ex d IIC T6..T5
All
Ex tb IIIC Db T 85oC
Intrinsically Safe:
Ga Ex ia IIC T4 X
FISCO Field Device
(Only for FF Option)
EAC
Ga Ex ia IIC T4 X
I
Russia, Belarus and
Kazakhstan
Zone 2, Non Sparking: 2 Ex nA IIC T4 Gc X
4-20 mA / DE/ HART
Foundation Fieldbus
4-20 mA / DE/ HART/ Foundation Fieldbus
Zone 2, Intrinsically Safe: Ga Ex ic IIC T4 X FISCO Field Device (Only for FF Option) 2 Ex ic IIC T4 Gc X
4-20 mA / DE/ HART/ Foundation Fieldbus
Enclosure : IP 66/67
All
Flameproof: Ex d IIC T6..T5 Ga/Gb
All
Intrinsically Safe: Ex ia IIC T4 Ga
4-20 mA / DE/ HART
J
CCoE INDIA
FISCO Field Device (Only for FF Option) Ex ia IIC T4 Ga; Ex ic IIC T4 Gc
Foundation Fieldbus
Non Sparking
4-20 mA / DE/
Ex nA IIC T4 Gc
HART/
Foundation
Fieldbus
Enclosure: IP66/ IP67
All
Flameproof:
II 1/2 G Ex db IIC T6..T5 Ga/Gb
All
II 2 D Ex tb IIIC T95oC...T120oC Db
K
UATR UKRAINE
Intrinsically Safe: II 1 G Ex ia IIC T4 Ga
4-20 mA / DE/ HART
FISCO Field Device (Only for FF Option) II 1 G Ex ia IIC T4 Ga
Foundation Fieldbus
Enclosure: IP66/ IP67
All
Notes:
1. Operating Parameters:
Voltage= 11 to 42 V DC
Current= 4-20 mA Normal
= 10 to 30 V (FF)
= 30 mA (FF)
Note 1 Note 2 Note 2
All Note 1 Note 2 Note 2
Note 1
Note 2
All Note 1 Note 2 Note 2
Note 1 All
Note 1 Note 2 Note 2
All
T4: -50oC TO 85oC T5: -50oC TO 85oC T6: -50oC TO 65oC Ta= -50 ºC to 70ºC Ta= -50 ºC to 70ºC
T5: -50oC TO 85oC T6: -50oC TO 65oC
-50oC TO 70oC -50oC TO 70oC
-50oC TO 85oC
-50oC TO 85oC
T5: -50oC TO 85oC T6: -50oC TO 65oC
-50oC TO 70oC -50oC TO 70oC
-50oC TO 85oC
T5: -50oC TO 85oC T6: -50oC TO 65oC
-50oC TO 70oC -50oC TO 70oC
-
2. Intrinsically Safe Entity Parameters
a. Analog/ DE/ HART Entity Values:
Vmax= Ui = 30V
Imax= Ii= 105mA
Ci = 4.2nF
Li =984 uH
Pi =0.9W
Transmitter with Terminal Block Revision E or Later
Vmax= Ui = 30V
Imax= Ii= 225mA
Ci = 4.2nF
Li = 0
Pi =0.9W
Note : Transmitter with Terminal Block Revision E or later
The revision is on the label that is on the module. There will be two lines of text on the label:
· First is the Module Part #: 50049839-001 or 50049839-002
· Second line has the supplier information, along with the REVISION:
XXXXXXX-EXXXX, THE "X" is production related, THE POSITION of the "E" IS THE REVISION.
b. Foundation Fieldbus- Entity Values
Vmax= Ui = 30V
Imax= Ii= 180mA
Ci = 0nF
Li = 984 uH
Pi =1W
Transmitter with Terminal Block Revision F or Later
Vmax= Ui = 30V
Imax= Ii= 225mA
Ci =0nF
Li = 0
Pi =1 W
FISCO Field Device
Imax= Ii= 380 mA
Ci = 0nF
Li = 0
Pi =5.32 W
Vmax= Ui = 17.5V
Note : Transmitter with Terminal Block Revision F or later
The revision is on the label that is on the module. There will be two lines of text on the label:
· First is the Module Part #: 50049839-003 or 50049839-004
· Second line has the supplier information, along with the REVISION:
XXXXXXX-EXXXX, THE "X" is production related, THE POSITION of the "E" IS THE REVISION
. Approval Certifications:
This certificate defines the certifications covered for the SmartLine Pressure Transmitter family of
products, including the SMV SmartLine Multivariable Transmitter. It represents the compilation of
the five certificates Honeywell currently has covering the certification of these products into marine
applications.
American Bureau of Shipping (ABS) - 2009 Steel Vessel Rules 1-1-4/3.7, 4-6-2/5.15, 4-8-3/13 &
Marine Certificates
13.5, 4-8-4/27.5.1, 4-9-7/13. Certificate number: 04-HS417416-PDA Bureau Veritas (BV) - Product Code: 389:1H. Certificate number: 12660/B0 BV
Det Norske Veritas (DNV) - Location Classes: Temperature D, Humidity B, Vibration A, EMC B,
Enclosure C. For salt spray exposure; enclosure of 316 SST or 2-part epoxy protection with 316
SST bolts to be applied. Certificate number: A-11476
Korean Register of Shipping (KR) - Certificate number: LOX17743-AE001
Lloyd's Register (LR) - Certificate number: 02/60001(E1) & (E2)
SIL 2/3 Certification IEC 61508 SIL 2 for non-redundant use and SIL 3 for redundant use according to EXIDA and TÜV
Nord Sys Tec GmbH & Co. KG under the following standards: IEC61508-1: 2010; IEC 61508-2:
MEASUREMENT INTRUMENTS DIRECTIVE (MID) 2004/ 22/ EC
2010; IEC61508-3: 2010.
Certificate Issued by NMI Certin B.V.
Mechanical Class: M3
Electromagnetic Environment: E3
Ambient Temperature Range: -25 oC to + 55 oC
Unit
Custom Calibration
STD820
0 to 1000 mBar
STD830
0 to 7 Bar
STA84L
0 to 35 Bar A
STG84L
0 to 35 Bar
STD870
0 to 100 Bar
STA87L
0 to 100 Bar A
STG87L
0 to 100 Bar
Application Data
Liquid Level: Closed Tank Determine the minimum and maximum pressure differentials to be measured (Figure 19). PMin = (SGp x a) - (SGf x d)
= LRV when HP at bottom of tank = URV when LP at bottom of tank PMax = (SGp x b) - (SGf x d) = URV when HP at bottom of tank = LRV when LP at bottom of tank Where: minimum level at 4mA maximum level at 20 mA a = distance between bottom tap and minimum level b = distance between bottom tap and maximum level d = distance between taps SGf = Specific Gravity of capillary fill fluid (See Page 6 "Material Specifications" for values.) SGp = Specific Gravity of process fluid
Figure 19--Closed tank liquid level measurement distance
Application Data (Cont'd)
Density or Interface* Calculate the minimum and maximum pressure differentials to be measured (Figure 20).
Pmin = (SGmin SGf) x (d); minimum density, 4mA output
Pmax = (SGmax SGf) x (d); maximum density, 20mA output
Where:
d = distance between the taps
SGmax = maximum Specific Gravity
SGmin = minimum Specific Gravity
SGf = Specific Gravity of capillary fill fluid (See Page 6 "Material Specifications" for values.)
Figure 20--Density, direct acting transmitter configuration
Seal Configurations
.
Figure 21--Flush Flange Seals and with left lower
Flush Flange Seals can be used with differential, gauge and absolute pressure transmitters and are available with 3" ANSI Class 150, ANSI Class 300 and DIN DN80-PN40 process connections. Flush flange seals can also be provided with Lowers. Lowers are essentially calibration rings, which allow flushing connections if needed.
Figure 23--Pancake Seals Pancake Seals can be used with differential, gauge and absolute pressure transmitters and are available with 3" ANSI Class 150, 300 and 600 process connections.
Figure 22-- Flange Seal with Extended Diaphragm
Flange Seal with Extended Diaphragm can be used with differential, gauge and absolute pressure transmitters and are available with 3" and 4" ANSI Class 150, ANSI Class 300, DIN DN80-PN40 and DIN DN100-PN40 process connections. 2", 4" and 6" extension lengths are available
Figure 24-- Chemical Tee "Taylor" Wedge Chemical Tee "Taylor" Wedge can be used with differential pressure transmitters and are available with Taylor Wedge 5" O.D. process connection.
Seal Configurations (cont'd)
Figure 25-- Seals with Threaded Process Connections
Seals with Threaded Process Connections can be used with differential, gauge and absolute pressure transmitters and are available with ½", ¾" and 1" NPT Female process connections.
Figure 29-- Stainless Steel Armor and PVC Coated Stainless Steel Armor Capillaries
Stainless Steel Armor and PVC Coated Stainless Steel Armor Capillaries are available with Honeywell Remote Seal Solutions.
Figure 26-- Sanitary Seals Sanitary Seals can be used with differential, gauge and absolute pressure transmitters and are available with 3" and 4" Tri-Clover-Tri-Clamp process connections.
Figure 30-- 2" Stainless Steel Nipples 2" Stainless Steel Nipples are available for CloseCoupled remote seal solutions
Figure 27-- Saddle Seals Saddle Seals can be used with differential, gauge and absolute pressure transmitters and are available with 3" and 4" (6 bolt or 8 bolt designs) process connections.
Figure 31-- Welded Meter Body for All-Welded Remote Seal Solution
Welded Meter Body for All-Welded Remote Seal Solution. The welded ST 800 meter body is an important part of an All-Welded Remote Seal Solution, which is commonly used in Vacuum applications.
Figure 28-- Calibration Rings Calibration Rings are available with Flush Flange Seals and Pancake Seals. Flushing ports (1/4" or ½") are available with calibration rings.
Model Selection Guide
Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Model STR800 (DP, GP & AP) Remote Seals
Model Selection Guide
34-ST-16-88 Issue 26
Instructions Select the desired Key Number. The arrow to the right marks the selection available. Make selections from each Table (I, II and IX) using the column below the proper arrow . A () denotes unrestricted availability. A letter denotes restricted availability. Restrictions follow Table IX.
Key Number STR _ _ _
I
II
III
IV
V
VI
VII
VIII
- _______ - _________ - _ - ___ - ___ - _ - ____ - __ +
IX 0 0 0 0
KEY NUMBER
Measurement Range Std Accuracy
URL 400 (1000)
100 (7) 500 (35) 500 (35) 3000 (210)
LRL -400 (-1000)
-100 (-7) 5.7 (0.39) -14.7 (-1.0) 14.7 (-1.0)
Max Span 400 (1000)
100 (7) 500 (35) 500 (35) 3000 (210)
Min Span 4 (10) 1 (0.07) 5 (0.35) 5 (0.35) 30 (2.1)
Units " H2O (mbar)
psi (bar) psia (bar A)
psi (bar) psi (bar)
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
Selection STR82D STR83D STR84A STR84G STR87G
TABLE I
Description
a. Number of Seals
b. Primary Fill Fluid
(Meter body)
1 Remote Seal (High Side) 2 Remote Seals
1 Remote Seal (Low Side) Silicone Oil 200
Fluorinated Oil CTFE
Silicone Oil 704 NEOBEE® M-20 11
c. Construction
Non-Wetted Adapter Head Materials
In-Line Gauge/ Absolute
Dual Head DP
316 SS Bonnet 316 SS Bonnet for Close-Couple
316 SS (bolt-on heads) 316 SS for Close-Couple 316 SS with all-welded meter body
None
d. Bolts and Nuts
Carbon Steel Bolts and Nuts
for Transmitter
316 SS Bolts and Nuts
Heads
A286 SS (NACE) Bolts and 304 SS (NACE) Nuts
B7M (NACE) Bolts and 7M (NACE) Nuts
Meter Body & Capillaries
No Fill Fluid
e. Secondary Fill Fluid (capillary &
seal)**
Silicone Oil 200 Fluorinated Oil CTFE
Silicone Oil 704 Neobee® M20 11
Syltherm® 800 12
No Capillary, No Nipple (Specify for VAM Unit Only)
5 feet
1.5 m
10 feet 3.0 m
f. Connection
15 feet 20 feet 25 feet
4.5 m 6.1 m 7.5 m
SS Armor
of Remote
Capillary 35 feet 10.7 m
Seal to Meter Length
5 feet
1.5 m
Body**
10 feet 15 feet
3.0 m 4.5 m
PVC Coated SS
20 feet 6.1 m
Arm or
25 feet 7.5 m
35 feet 10.7 m
2 inch long SS nipple close-coupled
None
g. Seal Option** Std Gold Plated Seal Diaph. = 50 µin
Teflon Coated Seal Diaphragm - only for anti-sticking ** Refer to 34-ST-00-128 for additional options, consult factory 11 Limited vacuum availability. 12 Minimum static pressure requirement. No vacuum allow ed. See Specifications 34-ST-03-88 Figure 15
Selection 1 _ _ _ _ _ _ 2 _ _ _ _ _ _ 3 _ _ _ _ _ _ _ 1 _ _ _ _ _ _ 2 _ _ _ _ _
_ 3 _ _ _ _ _
_ 4 _ _ _ _ _
_ _ A_ _ _ _ _ _ B _ _ _ _ _ _ C _ _ _ _ _ _ D _ _ _ _ _ _ E _ _ _ _ _ _ _ 0 _ _ _
_ _ _ C _ _ _
_ _ _ S _ _ _
_ _ _ N _ _ _
_ _ _ B _ _ _ _ _ _ _ 0 _ _ _ _ _ _ 1 _ _ _ _ _ _ 2 _ _ _ _ _ _ 3 _ _ _ _ _ _ 4 _ _ _ _ _ _ 5 _ _ _ _ _ _ _ 0 _ _ _ _ _ _ A_ _ _ _ _ _ B _ _ _ _ _ _ C _ _ _ _ _ _ D _ _ _ _ _ _ E _ _ _ _ _ _ F _ _ _ _ _ _ G _ _ _ _ _ _ H _ _ _ _ _ _ J _ _ _ _ _ _ K _ _ _ _ _ _ L _ _ _ _ _ _ M_ _ _ _ _ _ 2 _ _ _ _ _ _ _ 0 _ _ _ _ _ _ 1 _ _ _ _ _ _ 4
Availability
22
3 3 4 22 55 55 66 77 77
26
STR800 Smart Pressure Transmitter
In-Line Gauge
Dual Head DP
Note: When selecting required seal, you must specify only the 9 selections within the required s eal type.
TABLE II Seals
Description
No Seal Attached to Core Transm itter (Specify for VAM Unit Only)
Seal Type
Diaphragm Diameter
Flange Size
Flange Pressure Rating 1
3" 3.5"
80mm
ANSI Class 150 ANSI Class 300 DIN DN80-PN40
Diaphragm
Upper Insert
Wetted Material
Non-Wetted Material (upper)
316L SS Hastelloy® C-276 Hastelloy® C-276
316L SS
316L SS Hastelloy® C-276
Monel 400® Tantalum 5
Monel 400® 316L SS
CS (Nickel Plated)
316L SS
Flush Flanged Seal**
Seal-Capillary Connection
Calibration Rings
Flus hing
Center Seal Side Seal
None 316L SS Hastelloy® C-276 Monel 400®
None
Connections and Plugs 4 (Metal plug material
One 1/4" with plastic plug One 1/4" with metal plug Two 1/4" with plastic plugs
w ill be the same as
Two 1/4" with metal plugs
Cal. ring material if
One 1/2" with plastic plug
metal plug is chosen )
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
** Refer to 34-ST-00-128 for additional options, consult factory 1 Standard facing 125-250 AARH RF (raised face) serrated surface finish. 4 Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation 5 Tantalum Upper insert has Tantalum w etted parts and 316 SS or CS non-w etted parts
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
All welded STR84G & 87G & 84A STR82D & 83D
Selection
0 0 0 0 0 0 0 0 0
21 21
Se le ction
AFA _ _ _ _ _ _ AFC _ _ _ _ _ _
AFM _ _ _ _ _ _ Se le ction
_ _ _ AA _ _ _ _
_ _ _ AB _ _ _ _
_ _ _ AC _ _ _ _
_ _ _ AE _ _ _ _
88
_ _ _ AF _ _ _ _
88
_ _ _ _ _ 1 _ _ _
_ _ _ _ _ 2 _ _ _
_ _ _ _ _ _ 1 _ _
_ _ _ _ _ _ 2 _ _
99
_ _ _ _ _ _ _ A_
_ _ _ _ _ _ _ B _
10 10
_ _ _ _ _ _ _ C _
10 10
_ _ _ _ _ _ _ D _
10 10
_ _ _ _ _ _ _ _ 0
_ _ _ _ _ _ _ _ H
11 11
_ _ _ _ _ _ _ _ J
11 11
_ _ _ _ _ _ _ _ M
11 11
_ _ _ _ _ _ _ _ N
11 11
_ _ _ _ _ _ _ _ P
11 11
_ _ _ _ _ _ _ _ Q
11 11
_ _ _ _ _ _ _ _ R
11 11
_ _ _ _ _ _ _ _ S
11 11
Table II continued next page
STR84G & 87G & 84A STR82D & 83D
TABLE II
Descripton
Selection
Seal Type
Diaphragm Diameter
Flange Size
Flange
Pr e s s ur e Rating 1
Const. - See Spec. Figure 34-ST-03-88
Construction - See Spec. Figure 34-ST-03-88
ANSI 150
22
1"
ANSI 300
22
BCA _ _ _ _ _ _ BCC _ _ _ _ _ _
12 12
1-1/2"
ANSI 150
22
ANSI 300
22
2.4"
2"
ANSI 150
22
ANSI 300
22
BGA _ _ _ _ _ _ BGC _ _ _ _ _ _ BDA _ _ _ _ _ _ BDC _ _ _ _ _ _
12 12 12 12
ANSI 150
22
3"
ANSI 300
22
BFA _ _ _ _ _ _ BFC _ _ _ _ _ _
12 12
1/2"
ANSI 150
23
CAA _ _ _ _ _ _
ANSI 150
23
1"
ANSI 300
23
CCA _ _ _ _ _ _ CCC _ _ _ _ _ _
2.9"
1-1/2"
ANSI 150
22
ANSI 300
22
CGA _ _ _ _ _ _ CGC _ _ _ _ _ _
2"
ANSI 150
22
ANSI 300
22
CDA _ _ _ _ _ _ CDC _ _ _ _ _ _
1/2"
ANSI 150
22
DAA _ _ _ _ _ _
1"
ANSI 150
23
ANSI 300
23
DCA _ _ _ _ _ _ DCC _ _ _ _ _ _
1-1/2"
ANSI 150
23
4.1"
ANSI 300
23
DGA _ _ _ _ _ _ DGC _ _ _ _ _ _
2"
ANSI 150
23
ANSI 300
22
DDA _ _ _ _ _ _ DDC _ _ _ _ _ _
Seals (continued)
Flush Flanged Seal
with Lower**
3" Wetted Material
ANSI 150
ANSI 300 Diaphragm 316L SS Hastelloy® C-276 Hastelloy® C-276 Monel 400® Tantalum Tantalum
22
22
Low er 316L SS 316L SS Hastelloy® C-276 Monel 400® 316L SS Hastelloy® C-276
DFA _ _ _ _ _ _ DFC _ _ _ _ _ _
Selection _ _ _ BA _ _ _ _ _ _ _ BB _ _ _ _ _ _ _ BC _ _ _ _ _ _ _ BE _ _ _ _ _ _ _ BF _ _ _ _ _ _ _ BG _ _ _ _
88 88 88
Tantalum
Tantalum Clad
_ _ _ BH _ _ _ _
13 13
Non-Wetted Material (upper, upper insert)
Bolts 6
Uppe r
Upper Insert
316L SS
316L SS
Carbon Steel
316L SS
No Selection
Selection _ _ _ _ _ 4 _ _ _ _ _ _ _ _ 5 _ _ _ _ _ _ _ _ _ 0 _ _
Flus hing Connections and Plugs4 (Metal plug material w ill be the same as Low er material, if metal plug is chosen (SS Plug for CS Low er and Tantalum Clad)
Gas ket
None One 1/4" with plastic plug One 1/4" with metal plug Two 1/4" with plastic plugs Two 1/4" with metal plugs One 1/2" with plastic plug One 1/2" with metal plug Two 1/2" with plastic plugs Two 1/2" with metal plugs Klinger® C-4401 (non-asbestos) Grafoil® Teflon® Gylon® 3510
_______0 _ _ _ _ _ _ _ _ H _ _______J _ _ _ _ _ _ _ _ M_ _ _ _ _ _ _ _ N _ _ _ _ _ _ _ _ P _ _ _ _ _ _ _ _ Q _ _ _ _ _ _ _ _ R _ _ _ _ _ _ _ _ S _ _ _ _ _ _ _ _ _ K _ _ _ _ _ _ _ _ G _ _ _ _ _ _ _ _ T _ _ _ _ _ _ _ _ L
15 15
Table II continued next page
** Refer to 34-ST-00-128 for additional options, consult factory 1 Standard facing 125-250 AARH RF (raised face) serrated surface finish. 6 Bolt material w ill be same as Upper Material. How ever, if Table I bolts/nuts material is NACE or B7M, seal bolt material w ill be 304 SS NACE. 4 Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
28
STR800 Smart Pressure Transmitter
TABLE II Seals (continued)
Seal Type
Flange Seal with Extended Diaphragm **
No Selection
Descripton
Diaphragm Diameter
Flange Size
Flange Pressure Rating 1
3"
2.8"
(2.8" OD
ANSI Class 150 ANSI Class 300
extension) 4"
3.5" (3.70" OD
DIN DN80-PN40 ANSI Class 150 ANSI Class 300
extension
DIN DN100-PN40
Diaphragm
Ext. Tube
Wetted Material
316L SS Hastelloy® C-276 Hastelloy® C-276
316L SS 316L SS Hastelloy® C-276
Non-Wetted
CS (Nickel Plated)
Material (flange)
316L SS
Bolts
No Selection
2"
Extension Length
4"
6"
No Selection
No Selection
TABLE II
Descripton
Seal Type
Diaphragm Diameter
Flange Flange Pressure Rating Dependent
Size
on Custom er Flange 1
3.5"
3"
Wetted Material
ANSI Class 150/300/600
Diaphragm
Body
316L SS Hastelloy® C-276 Hastelloy® C-276
316L SS
316L SS Hastelloy® C-276
Monel 400® Tantalum
Monel 400® Tantalum 7
Non-Wetted Material
No Selection
Seals (continued)
Bolts Calibration Rings
No Selection None
Pancake Seal Flus hing
316L SS Hastelloy® C-276
Monel 400® None
Connections
One 1/4" with plastic plug
and Plugs4 (Metal plug material
One 1/4" with metal plug Two 1/4" with plastic plugs
w ill be the same as
Two 1/4" with metal plugs
Cal. Ring material, if
One 1/2" with plastic plug
metal plug is chosen)
One 1/2" with metal plug
Two 1/2" with plastic plugs
Two 1/2" with metal plugs
** Refer to 34-ST-00-128 for additional options, consult factory 1 Standard facing 125-250 AARH RF (raised face) serrated surface finish. 4 Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation 7 Tantalum Body has Tantalum w etted parts and 316 SS non-w etted parts
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
STR84G & 87G & 84A STR82D & 83D
Se le ction
EFA _ _ _ _ _ _ EFC _ _ _ _ _ _ EFM _ _ _ _ _ _ FGA _ _ _ _ _ _ FGC _ _ _ _ _ _ FGP _ _ _ _ _ _
Selection _ _ _ EA _ _ _ _ _ _ _ EB _ _ _ _ _ _ _ EC _ _ _ _ _ _ _ _ _ 7 _ _ _ _ _ _ _ _ 8 _ _ _ _ _ _ _ _ _ 0 _ _ _______2 _ _ _ _ _ _ _ _ 4 _ _ _ _ _ _ _ _ 6 _ _ _ _ _ _ _ _ _ 0
STR84G & 87G & 84A STR82D & 83D
Se le ction
GFA _ _ _ _ _ _
_ _ _ GA _ _ _ _ _ _ _ GB _ _ _ _ _ _ _ GC _ _ _ _ _ _ _ GE _ _ _ _ _ _ _ GG _ _ _ _
_ _ _ _ _ 0 _ _ _
_ _ _ _ _ _ 0 _ _ _ _ _ _ _ _ _ A_ _ _ _ _ _ _ _ B _ _ _ _ _ _ _ _ C _ _ _ _ _ _ _ _ D _ _ _ _ _ _ _ _ _ 0 _ _ _ _ _ _ _ _ H _ _ _ _ _ _ _ _ J _ _ _ _ _ _ _ _ M _ _ _ _ _ _ _ _ N _ _ _ _ _ _ _ _ P _ _ _ _ _ _ _ _ Q _ _ _ _ _ _ _ _ R _ _ _ _ _ _ _ _ S
88 88
10 10 10 10 10 10 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11 11
TABLE II Seals (continued)
Seal Type
Chemical Tee "Taylor" Wedge
Descripton
Diaphragm Diameter
Flange Size
Flange Pressure Rating 1
Taylor
3.5"
Wedge
5" O.D.
750 psi
Wetted Material
Non-Wetted Material Bolts Styles
No Selection
Diaphragm
Body
316L SS Hastelloy® C-276
316L SS 316L SS
Hastelloy® C-276 Hastelloy® C-276
No Selection
No Selection
No Selection
No Selection
STR84G & 87G & 84A STR82D & 83D
Se le ction
HM0 _ _ _ _ _ _
16
Selection
_ _ _ HA _ _ _ _
_ _ _ HB _ _ _ _
_ _ _ HC _ _ _ _
_ _ _ _ _ 0 _ _ _
_ _ _ _ _ 0 _ _
_______0 _
_ _ _ _ _ _ _ _ 0
Table II continued below
STR84G & 87G & 84A
TABLE II
Descripton
STR82D &83D
Seal Type
Diaphragm Diameter
Threaded Process Connection Size (NPT Fem ale)
Pressure Rating
CS Bolts
304 SS Bolts
Selection
2.4"
1/2 NPT 3/4 NPT
2,500 psi
1,250 psi
JJG _ _ _ _ _ _ JKG _ _ _ _ _ _
12 12
1 NPT
JLG _ _ _ _ _ _
12
2.9"
1/2 NPT 3/4 NPT
2,500 psi
1,250 psi
KJG _ _ _ _ _ _ KKG _ _ _ _ _ _
1 NPT
KLG _ _ _ _ _ _
4.1"
1/2 NPT 3/4 NPT
1,500
750
psi
psi
LJG _ _ _ _ _ _ LKG _ _ _ _ _ _
1 NPT
LLG _ _ _ _ _ _
Diaphragm
Low er
Selection
Seals (continued)
Seal with Threaded Proces s Connection
Wetted Material
Non-Wetted Material (upper)
316L SS
Carbon Steel
316L SS Hastelloy® C-276 Hastelloy® C-276
316L SS
316L SS Hastelloy® C-276
Monel 400®
Monel 400®
Tantalum Tantalum
316L SS Hastelloy® C-276
CS (Nickel Plated)
316 Stainless Steel
_ _ _ JA _ _ _ _ _ _ _ JB _ _ _ _ _ _ _ JC _ _ _ _ _ _ _ JD _ _ _ _ _ _ _ JE _ _ _ _ _ _ _ JF _ _ _ _ _ _ _ JG _ _ _ _ _ _ _ _ _ A_ _ _ _ _ _ _ _ C _ _ _
88
88
88
17 17
Bolts 8
Flus hing Connections and Plugs4
(Metal plug material w ill be the same as
Low er material, if
Carbon Steel 304 SS None
One 1/4" with plastic plug One 1/4" with metal plug Two 1/4" with plastic plugs Two 1/4" with metal plugs One 1/2" with plastic plug
_ _ _ _ _ _ C _ _ _ _ _ _ _ _ D _ _ _______0 _ _ _ _ _ _ _ _ H _ _______J _ _ _ _ _ _ _ _ M_ _ _ _ _ _ _ _ N _ _ _ _ _ _ _ _ P _
18 18
metal plug is chosen -
One 1/2" with metal plug
_ _ _ _ _ _ _ Q _
18 18
(SS Plug for CS Low er Two 1/2" with plastic plugs
_ _ _ _ _ _ _ R _
18 18
and Tantalum Clad)
Two 1/2" with metal plugs
Gas ket
Klinger® C-4401 (non-asbestos) Grafoil® Teflon®
Gylon® 3510
_ _ _ _ _ _ _ S _ _ _ _ _ _ _ _ _ K _ _ _ _ _ _ _ _ G _ _ _ _ _ _ _ _ T _ _ _ _ _ _ _ _ L
18 18 15 15
1 Standard facing 125-250 AARH RF (raised face) serrated surface finish. 4 Plastic Plugs are TEMPORARY ONLY to protect threads and MUST be REMOVED before installation 8 If Table I Bolts and Nuts material option is NACE, Bolts and Nuts w ill ship w ith Alloy Steel NACE and MAWP may change.
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
30
STR800 Smart Pressure Transmitter
TABLE II Seals (continued)
Seal Type Sanitary Seal 9
Descripton
Diaphragm Diameter
Flange Size
Pressure Rating
1.9"
2"
2.4"
2-1/2"
2.9"
3"
Customer clamp rating or 600 psi, whichever is less
4.1"
4"
Wetted Material
Diaphragm 316L SS
Body 316L SS
Non-Wetted Material
No Selection
Bolts Styles Gas ket
No Selection Tri-Clover Tri-Clamp®
No Selection
TABLE II
Descripton
Seal Type
Diaphragm Diameter
Size and Bolt
Patte r n
Seal Pressure Rating
C.S. Bolts
316 SS Bolts
2.4" 8-Bolt Design 2.4" 6-Bolt Design
for 3" Pipe 4" pipe
for 3" Pipe 4" pipe
2,500 psi
2,000 psi Diaphragm 316L SS
1,250 psi
1,000 psi Low er Housing Carbon Steel
Seals (continued)
Saddle Seal
Wetted Material
316L SS Hastelloy® C-276 Hastelloy® C-276
316L SS Hastelloy® C-276
Body
316L SS
316L SS Hastelloy® C-276 N/A-Body Only 10 N/A-Body Only 10
Bolts 10,11
Non-Wetted Material Carbon Steel 316L SS
Carbon Steel 316 SS
Bolts
No Selection
Styles
No Selection
Klinger® C-4401 (non-asbestos)
Gas ket
Grafoil® Teflon®
Gylon® 3510
9 All sanitary seals have dairy grade 3A approval. 10 Bolts are not included w ith "body only" selection. 11 If Table I Bolts and Nuts material option is NACE, seal bolt material w ill be 304 SS NACE.
Note: Remote seal system pressure rating is body rating or seal rating, w hichever is less.
STR84G & 87G & 84A STR82D & 83D
Selection
MD0 _ _ _ _ _ _
19
NE0 _ _ _ _ _ _
20 19
PF0 _ _ _ _ _ _
19 19
QG0 _ _ _ _ _ _
19 19
Selection
_ _ _ N A_ _ _ _ _ _ _ _ _ 0 _ _ _ _ _ _ _ _ _ 0 _ _ _______8 _
_ _ _ _ _ _ _ _ 0
Table II continued below
STR84G & 87G & 84A STR82D & 83D
Selection
RFK _ _ _ _ _ _
RGK _ _ _ _ _ _
RPK _ _ _ _ _ _
RQK _ _ _ _ _ _ Selection
_ _ _ RA _ _ _ _ _ _ _ RB _ _ _ _ _ _ _ RC _ _ _ _ _ _ _ RD _ _ _ _ _ _ _ SB _ _ _ _ _ _ _ SC _ _ _ _
Selection _ _ _ _ _ B _ _ _ _ _ _ _ _ C _ _ _ _ _ _ _ _ _ 0 _ _ _ _ _ _ _ _ _ 0 _ _ _ _ _ _ _ _ _ K _ _ _ _ _ _ _ _ G _ _ _ _ _ _ _ _ T _ _ _ _ _ _ _ _ L
12
12
12
12
88
STR84G & 87G & 84A STR82D & 83D
TABLE III Approvals
Agency Approvals (see data sheet for Approval Code Details) No Approvals Required FM Explosion proof, Intrins ically Safe, Non-incendive, & Dus tproof CSA Explos ion proof, Intrins ically Safe, Non-incendive, & Dus tproof ATEX Explos ion proof, Intrins ically Safe & Non-incendive IECEx Explosion proof, Intrins ically Safe & Non-incendive SAEx Explosion proof, Intrins ically Safe & Non-incendive INMETRO Explosion proof, Intrins ically Safe & Non-incendive NEPSI Explosion proof, Intrins ically Safe & Non-incendive KOSHA Explos ion proof, Intrins ically Safe & Non-incendive EAC Custom s Union(Russ ia,Belarus,Kazakhstan) Ex Approval,Flam eproof, Intrinsically Safe CCoE Explosion proof, Intrins ically Safe & Non-incendive UATR Flam eproof, Intrins ically Safe & Dustproof
0
A
B
C
D
E
F
G
H
I
J
K
TABLE IV
TRANSMITTER ELECTRONIC SELECTIONS
M ate r ial
Conne ction
Lightning Protection
Polyester Powder Coated Aluminum
1/2 NPT
None
Polyester Powder Coated Aluminum
a. Electronic Polyester Powder Coated Aluminum
Housing Material
& Connection Polyester Powder Coated Aluminum
Type
316 Stainless Steel (Grade CF8M)
316 Stainless Steel (Grade CF8M)
M20 1/2 NPT
M20 1/2 NPT
M20
None Yes Yes None None
316 Stainless Steel (Grade CF8M)
1/2 NPT
Yes
316 Stainless Steel (Grade CF8M)
M20
Yes
Analog Output
Digital Protocol
b. Output/ Protocol
4-20m A dc 4-20m A dc
HART Protocol DE Protocol
Indicator
none
p
g
Buttons
Foundation Fieldbus Language s
None
None
None
None
Yes (Zero/Span Only)
None
c. Customer
Bas ic
None
Englis h
Interface Selections
Bas ic Advanced
Yes None
Englis h EN,GR,IT, FR,SP,RU, TU
Advanced
Yes
EN,GR,IT, FR,SP,RU, TU
Advanced
None
EN, CH, JP
Advanced
Yes
EN, CH, JP
A _ _ B _ _ C _ _ D _ _ E _ _ F _ _ G _ _ H _ _
_ H _ _ D _ _ F _
_ _ 0 _ _ A _ _ B _ _ C _ _ D _ _ E _ _ H _ _ J
ff
TABLE V
CONFIGURATION SELECTIONS
a. Application Software Standard Diagnostics
Diagnostics
Write Protect
Fail Mode
High & Low Output Lim its3
Disabled
High> 21.0mAdc
Honeywell Std (3.8 - 20.8 mAdc)
b. Output Limit, Failsafe & Write Protect Settings
Disabled Enabled Enabled
Low< 3.6mAdc High> 21.0mAdc Low< 3.6mAdc
Honeywell Std (3.8 - 20.8 mAdc) Honeywell Std (3.8 - 20.8 mAdc) Honeywell Std (3.8 - 20.8 mAdc)
Enabled
N/A
N/A Fieldbus or Profibus
Disabled
N/A
N/A Fieldbus or Profibus
c. General Configuration
Factory Standard Custom Configuration (Unit Data Required from customer)
1 _ _
_ 1 _ _ 2 _ _ 3 _ _ 4 _ _ 5 _ _ 6 _ _ _ S _ _ C
ff ff ff ff gg gg
TABLE VI
Accuracy and Calibration
Accuracy NA
Standard Standard
CALIBRATION & ACCURACY SELECTIONS
Calibrated Range
Calibration Qty
None
None
Factory Std
Single Calibration
Custom (Unit Data Required)
Single Calibration
3 NAMUR Output Limits 3.8 - 20.5mAdc can be conf igured by the customer or select custom conf iguration Table Vc
0
21 21
A
23 23
B
23 23
32
TABLE VII
ACCESSORY SELECTIONS
a. Mounting Bracket
Bracket Type None
Angle Bracket Angle Bracket Angle Bracket Marine Approved Bracket Marine Approved Bracket (In Line)
Marine Approved Bracket Marine Approved Bracket (In Line)
Flat Bracket Flat Bracket Flat Bracket
M ate r ial None
Carbon Steel 304 SS 316 SS
Carbon Steel Carbon Steel
304 SS 304 SS Carbon Steel 304 SS 316 SS
b. Customer Tag
Custom er Tag Type
No customer tag One Wired Stainless Steel Tag (Up to 4 lines 26 char/line) Two Wired Stainless Steel Tag (Up to 4 lines 26 char/line)
Unassem bled Conduit Plugs & Adapters
c. Unassembled No Conduit Plugs or Adapters Required
Conduit
1/2 NPT Male to 3/4 NPT Female 316 SS Certified Conduit Adapter
Plugs & 1/2 NPT 316 SS Certified Conduit Plug
Adapters
M20 316 SS Certified Conduit Plug Minifast® 4 pin (1/2 NPT)
Minifast® 4 pin (M20)
TABLE VIII
Certifications & Warranty
OTHER Certifications & Options : (String in sequence comma delimited (XX, XX, XX,....) None - No additional options NACE MR0175; MR0103; ISO15156 (FC33338) Process wetted parts only NACE MR0175; MR0103; ISO15156 (FC33339) wetted and non-wetted parts Marine (DNV,ABS,BV,KR,LR) EN10204 Type 3.1 Material Traceability (FC33341) Certificate of Conformance (F3391) Calibration Test Report & Certificate of Conformance (F3399) Certificate of Origin (F0195) FMEDA (SIL 2/3) Certification (FC33337) Over-Pres s ure Leak Tes t Certificate (1.5X MAWP) (F3392) Cert Clean for O2 or CL2 service per ASTM G93
Extended Warranty Additional 1 year Extended Warranty Additional 2 years Extended Warranty Additional 3 years Extended Warranty Additional 4 years Extended Warranty "LifeTim e" Additional 15 years
TABLE IX Factory
Manufacturing Specials Factory Identification
STR800 Smart Pressure Transmitter
STR84G & 87G & 84A STR82D & 83D
0 _ _ _ 1 _ _ _ 2 _ _ _ 3 _ _ _ 8 _ _ _ 9 _ _ _ 4 _ _ _ A_ _ _ 5 _ _ _ 6 _ _ _ 7 _ _ _
_ 0 _ _ _ 1 _ _ _ 2 _ _
_ _ A0 _ _ A2 _ _ A6 _ _ A7 _ _ A8 _ _ A9
y
y
nn nn mm nn mm
00
**
FG F7
** cc
b
MT
dd
FX
F3 F1
b
F5
FE
jj
TP
OX
ee
01
02
03
b
04
15
0 0 0 0
MODEL RESTRICTIONS
Restriction
Letter
Table
b
d
IVa
c
Id
e
Ib
f
g
j
IVb
m
IVa
n
IVa
y
2
Ie
3
If
4
I
Available Only With
Not Available With
Selection(s)
Table
Selection(s)
Select only one option from this group
C, D,G,H _ _
VIIa
1,2,3,5,6,7 _ _ _
_ _ _ 0, N, B _ _ _
_ 2 _ _ 2 _ _
_ H _ B, D, F, H _ _ A, C, E, G _ _
_ _ _ _ 0 _ _ _ _ _ _ 2 _ _ _ _ _ _ 4 _ _ _ _ _ _ _ 2 _
IVb
_ F _
IVb
_ H, D _
Vb
_ 1,2,6 _
Ic
_ _ E _ _ _ _
Ia
2 _ _ _ _ _ _
2 _ _ 0 _ _ _
5
II
000000000
VIII
FG, F7, FX, OX,TP,MT,F1
6
I
7
8
9
II
10
11
12
If
13
II
15
II
16
I
17
18
19
If 20
_ _ B,D _ _ _ _
_ _ _ AA2_ _ _ _ _ _ AB2_ _ _ _ _ _ _ _ A, G, 2 _ _ _ _ _ _ _ _ 0 _ _ _ _ BF _ _ _ _ _ _ _ BG _ _ _ _ _ _ _ BH _ _ _ _ _ _ _ JF _ _ _ _ _ _ _ JG _ _ _ _ 2 _ _ _ _ _ _
_ _ _ _ _ A,G _
Ia
2 _ _ _ _ _ _
_ _ _ AF _ _ _ _
_ _ _ BF _ _ _ _
_ _ _ BG _ _ _ _
II
_ _ _ BH _ _ _ _
_ _ _ GG _ _ _ _
_ _ _ JF _ _ _ _
_ _ _ JG _ _ _ _
VIII
FG, F7
II
_ _ _ _ _ _ _ _ 0
II
_ _ _ _ _ _ _ A_
II
_ _ _ _ _ _ _ _ T
VIII
FG, F7
II
_ _ _ JA _ _ _ _
JJG _ _ _ _ _ _
II
JKG _ _ _ _ _ _
JLG _ _ _ _ _ _
If
_ _ _ _ _ 2 _
21
I
_ _ _ _ 000
22
Ic
_ _ E _ _ _ _
23
II
FM ApprovalsSM is a service mark of FM Global
Hastelloy® is a registered trademark of Haynes International
Monel 400® is a registered trademark of Special Metals Corporation.
HART® is a registered trademark of HART Communication Foundation.
FOUNDATIONTM Fieldbus is a registered trademark of Fieldbus Foundation.
Teflon® is a registered trademark of DuPont.
Neobee® is a registered trademark of Stepan Company.
Syltherm® 800 is a Trademark of Dow Corning Corporation
Klinger® C-4401 is a registered trademark of THERMOSEAL, INC
GRAFOIL® is a registered trademarks of GrafTech International Holdings Inc Gylon® 3510 is registered trademark of Garlock Sealing Technologies
Tri-Clover Tri-Clamp® is a registered trademark of Alf a-Laval DC® 200 and DC® 704 are registered trademarks of Dow Corning
000000000
34
FIELD INSTALLABLE REPLACEMENT PARTS Description
Integrally Mounted Bas ic Indicator Kit (Com patible with all Electronic Modules ) Integrally Mounted Advanced Indicator Kit (Com patible with all Electronic Modules) Terminal Strip w/Lightning Protection Kit for HART or DE Modules Terminal Strip w/Lightning Protection Kit for FFB Module Terminal Strip w/o Lightning Protection for HART or DE Modules Terminal Strip w/o Lightning Protection FFB Module HART Electronics Module HART Electronics Module w/connection for external configuration buttons DE Electronics Module DE Electronics Module w/connection for external configuration buttons FFB Electronics Module Kit FFB Electronics Module w/connection for external configuration buttons
PRODUCT MANUALS Description
Paper Manual ST 800 Smart Transmitter User Manual - English Paper Manual ST 800 Smart Transmitter HART/DE Communications Manual - English Paper Manual ST 800 Sm art Trans m itter Safety Manual - English Paper Manual ST 800 Smart Transmitter Foundation Fieldbus Manual - English Paper Manual ST 800 Smart Transmitter Function Block Manual - English All product documentation is available at www.honeywellprocess.com.
STR800 Smart Pressure Transmitter
Kit Number 50049911-501 50049846-501 50075472-532 50075472-534 50075472-531 50075472-533 50049849-501 50049849-502 50049849-503 50049849-504 50049849-507 50049849-508
Part Number 34-ST-25-35 34-ST-25-38 34-ST-25-37 34-ST-25-39 34-ST-25-42
Sales and Service
For application assistance, current specifications, ordering, pricing, and name of the nearest Authorized Distributor, contact one of the offices below.
ASIA PACIFIC
Honeywell Process Solutions, Phone: + 800 12026455 or +44 (0) 1202645583 (TAC) hfs-tacsupport@honeywell.com
Australia Honeywell Limited Phone: +(61) 7-3846 1255 FAX: +(61) 7-3840 6481 Toll Free 1300-36-39-36 Toll Free Fax: 1300-36-04-70
China PRC - Shanghai Honeywell China Inc. Phone: (86-21) 5257-4568 Fax: (86-21) 6237-2826
Singapore Honeywell Pte Ltd. Phone: +(65) 6580 3278 Fax: +(65) 6445-3033
South Korea Honeywell Korea Co Ltd Phone: +(822) 799 6114 Fax: +(822) 792 9015
EMEA
Honeywell Process Solutions, Phone: + 800 12026455 or +44 (0) 1202645583
Email: (Sales) FP-Sales-Apps@Honeywell.com or (TAC) hfs-tac-support@honeywell.com
Web Knowledge Base search engine http://bit.ly/2N5Vldi
AMERICAS
Honeywell Process Solutions, Phone: (TAC) (800) 423-9883 or (215) 641-3610 (Sales) 1-800-343-0228
Email: (Sales) FP-Sales-Apps@Honeywell.com or (TAC) hfs-tac-support@honeywell.com
Web Knowledge Base search engine http://bit.ly/2N5Vldi
Specifications are subject to change without notice.
For more information To learn more about SmartLine Pressure Transmitters, visit www.honeywellprocess.com Or contact your Honeywell Account Manager
Process Solutions Honeywell 1250 W Sam Houston Pkwy S Houston, TX 77042
Honeywell Control Systems Ltd Honeywell House, Skimped Hill Lane Bracknell, England, RG12 1EB
Shanghai City Centre, 100 Jungi Road Shanghai, China 20061
www.honeywellprocess.com
34-ST-03-88 October 2020
2020 Honeywell International Inc.
Steve Kennedy Adobe PDF Library 15.0