SAFETY INSTRUCTIONS. 3. 1. Save these instructions and ensure that other exercisers read this manual prior to using the WirkTM Ride. Workstation for the first ...
Exercise can present a health risk. Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately.
Stamina WIRK Ride with Strength System Warranty:
Owner's Manual
Product May Vary Slightly From Pictured.
CAUTION: Weight on the Seat should not exceed 300 lbs. Weight on the Desktop should not exceed 30 lbs.
This Product is Distributed Exclusively by
2040 N Alliance Ave, Springfield, MO 65803 Customer Care 1 (800) 375-7520
www.staminaproducts.com
! WARNING
Exercise can present a health risk. Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use. Always make sure all bolts and nuts are securely tightened prior to each use. Follow all safety instructions in this manual.
When calling for parts or service, please specify the following numbers :
Model#: 85-2449
S/N: _____________
STAMINA PRODUCTS
MADE IN CHINA
©2017 Stamina Products, Inc. 2019, 10
TABLE OF CONTENTS
Safety Instructions ...................................... 3 Before You Begin ........................................ 5 Equipment Warning, Caution & Notice Labels ... 6 Hardware Identification Chart .................... 7 Assembly Instructions ................................ 8 Set Up Instructions ................................... 13 Operational Instructions ........................... 14 Storage ....................................................... 19 Maintenance ............................................... 19
SAFETY INSTRUCTIONS
Conditioning Guidelines ........................... 20 Warm-Up and Cool-Down ......................... 21 Product Parts Drawing .............................. 22 Parts List .................................................... 23 Warranty ..................................................... 26 WirkTM Coaster Toss Rules ....................... 27 Notes ........................................................... 28 Fax/Mail Ordering Form ............................ 30
! WARNING Cancer and Reproductive Harm www.P65Warnings.ca.gov ! WARNING Consult your physician before starting this or any exercise program. This is
especially important if you are over the age of 35, have never exercised before, are pregnant, or suffer from any health problem. This product is for home use only. Do not use in institutional or commercial applications. Failure to follow all warnings and instructions could result in serious injury or death. ! WARNING The Tension Cords(129, 130) on this product contain natural rubber latex which may cause an allergic reaction. ! WARNING To reduce the risk of serious injury, read the following Safety Instructions before using the WirkTM Ride Workstation.
1. Save these instructions and ensure that other exercisers read this manual prior to using the WirkTM Ride Workstation for the first time.
2. Read all warnings and cautions posted on the WirkTM Ride Workstation. 3. The WirkTM Ride Workstation should only be used after a thorough review of the Owner's Manual. Make
sure that it is properly assembled and tightened before use. 4. We recommend that two people be available for assembly of this product. 5. Keep children away from the WirkTM Ride Workstation. Do not allow children to use or play on the WirkTM
Ride Workstation. Keep children and pets away from the WirkTM Ride Workstation when it is in use. 6. The WirkTM Ride Workstation is not a freewheeling exercise bike; therefore, pedal speed should be
reduced in a controlled manner to prevent injury from spinning pedals. 7. It is recommended that you place this exercise equipment on an equipment mat. 8. Set up and operate the WirkTM Ride Workstation on a solid level surface. Do not position the WirkTM Ride
Workstation on loose rugs or uneven surfaces. 9. Remove all items from the Desktop(21) before moving or folding the WirkTM Ride Workstation. 10. Remove all items from the Desktop(21) when the WirkTM Ride Workstation is not in use. 11. Make sure that adequate space is available for access to and around the WirkTM Ride Workstation. 12. Keep fingers clear of all pinch points when folding and unfolding the WirkTM Ride Workstation. 13. Before using, inspect the WirkTM Ride Workstation for worn or loose components, and securely tighten or
replace any worn or loose components prior to use. 14. Each user should adjust the seat per instructions on page 16. 15. Do not attempt to adjust the seat while you are on the WirkTM Ride Workstation. 16. Make sure the Table Post(4) and Seat Post(6) is locked properly by the Adjustment Knobs(36). 17. Make sure the Rear Frame(2) is locked properly by the Pull Pin(49) when in storage. 18. Consult a physician prior to commencing an exercise program and follow his/her recommendations in
developing your fitness program. If at any time during exercise you feel faint, dizzy, or experience pain, stop and consult your physician. 19. Always choose the workout which best fits your physical strength and flexibility level. Know your limits and train within them. Always use common sense when exercising. 20. Do not wear loose or dangling clothing while using the WirkTM Ride Workstation. 21. Never exercise in bare feet or socks; always wear proper footwear such as running, walking, or cross training shoes that fit well, provide foot support, and feature non-skid rubber soles. 22. Be careful to maintain your balance while using, mounting, dismounting, or assembling the WirkTM Ride Workstation, loss of balance may result in a fall and serious bodily injury. 23. The WirkTM Ride Workstation should not be used by persons weighing over 300 pounds. 24. The WirkTM Ride Workstation should be used by only one person at a time. 25. The WirkTM Ride Workstation is for consumer use only. It is not for use in public or semipublic facilities.
3
NEED HELP?
CONTACT US FIRST
1 (800) 375-7520
customer.care@staminaproducts.com
Hi! From all of us here at Stamina Products, thank you for your purchase. We know that you have big fitness goals in mind and we are here to help you along. Call us, email us, or send us a message on Facebook. Be sure to contact us if you have any questions on your new product. We look forward to hearing from you!
With your body in mind, Stamina Customer Care
To enact your extended warranty and to help us better serve you, please go online and register your new product.
register.staminaproducts.com
It is quick and easy to register online, but if you're a little old school or just need a reason to raise that little flag on your mailbox, fill out the info on the last page of this
manual and mail it in.
ONLINE
customer.care@staminaproducts.com www.staminaproducts.com
TELEPHONE
1 (800) 375-7520
FAX
(417) 889-8064
MAIL
Stamina Products, Inc. ATTN: Customer Care 2040 N Alliance Ave Springfield, MO 65803
facebook.com/StaminaProducts facebook.com/AeroPilates
CUSTOMER CARE HOURS: Monday-Thursday, 7:30 AM-5:00 PM, Central Time
Friday, 8:00 AM-3:00 PM, Central Time
BEFORE YOU BEGIN
Thank you for choosing the WirkTM Ride Workstation. We take great pride in this quality product and hope it will provide many hours of quality exercise to make you feel better, look better, and enjoy life to its fullest.
It's a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise. The WirkTM Ride Workstation provides a convenient and simple method to begin your journey of getting your body in shape and achieving a happier and healthier lifestyle.
Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Locate the serial decal on the product and write the serial number on the cover of the manual in the space provided. See page 6 for an image of the serial decal. Model
number and serial number are required when calling for assistance.
Read this manual carefully before using the WirkTM Ride Workstation.
Providing you with a quality product is Stamina's top priority. However, sometimes there could be a missing or incorrectly sized part. If you have any questions or problems with the parts included with your WirkTM Ride Workstation, please do not return the product. Contact us FIRST!
If a part is missing or defective, please contact Customer Care for assistance. Call us toll free at 1-800-375-7520 (in the U.S.) or live chat on staminaproducts.com. Our Customer Care Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday.
Be sure to have the name and model number of the product available when you contact us.
Arm Endcap
Hand Strap Meter
Back Cushion
Left Resistance Arm
Arm Bracket Adjustment Pin
Back Frame Handrail
Seat
Rear Frame
Rear Stabilizer
Leveling Cap
Wheel Caution Label
Serial Decal
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY : Allen Wrench (6mm) 5
Strap
Desktop
Upright
Right Cover
Lever Right Pedal Strap Right Pedal Endcap Front Stabilizer Right Crank
Combination Wrench Allen Wrench (5mm)
EQUIPMENT WARNING, CAUTION & NOTICE LABELS
This chart is provided to help identify the warning, caution, and notice labels on the WirkTM Ride Workstation. Please take a moment to familiarize yourself with all of the warning, caution, and notice labels.
CAUTION LABEL(103)
SERIAL DECAL(137)
To best serve you, our Customer Care Representatives will need your serial number. For quick access, write in your serial number on the cover of the manual.
6
HARDWARE IDENTIFICATION CHART
This chart is provided to help identify the hardware used in the assembly process. Place the washers or the ends of the bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.
3/16" 1/4" 5/16"
3/8"
1/2"
INCHES
0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6 in.
mm. 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
MILLIMETERS
6
8
10
12
NOTICE: The length of all bolts and screws, except those with flat heads, is measured from below the head to the end of the bolt or screw. Flat head bolts and screws are measured from the top of the head to the end of the bolt or screw.
length length
After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware may be already attached to the part.
Part Number and Description
Qty
62 Carriage Bolt (M8 x 1.25 x 65mm)
4
65 Carriage Bolt (M8 x 1.25 x 48mm)
2
64 Bolt, Button Head (M8 x 1.25 x 40mm)
2
67 Bolt, Button Head (M8 x 1.25 x 20mm)
7
71 Bolt, Button Head (M8 x 1.25 x 12mm)
3
74 Screw, Round Head (M6 x 1 x 12mm)
1
76 Bolt, Socket Head (M6 x 1 x 12mm)
1
77 Bolt, Socket Head (M8 x 1.25 x 15mm)
2
79 Acorn Nut (M8 x 1.25)
4
80 Arc Washer (M8)
6
81 Washer (M8)
12
82 Nylock Nut (M8 x 1.25)
2
90 Lock Washer (M8)
2
7
ASSEMBLY INSTRUCTIONS
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part, please go to staminaproducts.com under the Customer Care section and order the part needed, e-mail us at customer.care@staminaproducts.com, or call us toll free at 1-800-375-7520 (in the U.S.). Our Customer Care Staff is available to assist you from 7:30 A.M. to 5:00 P.M. (Central Time) Monday through Thursday and 8:00 A.M. to 3:00 P.M. (Central Time) on Friday. Some product parts are fit tested at the factory to ensure proper fit and alignment. Marks in the paint may be noticeable, but are not an indication of damage. STEP 1 Refer to illustration A. Remove the PULL PIN(49) from the REAR FRAME(2). Unfold the REAR FRAME(2) away from the MAIN FRAME(1). Lock the frame assembly in unfolded position by inserting the PULL PIN(49) into the hole in the REAR FRAME(2). STEP 2 Attach the REAR STABILIZER(10), the one with WHEELS(32), to the REAR FRAME(2) with the wheels facing backward. Secure with CARRIAGE BOLTS(M8x1.25x65mm)(62), ACORN NUTS(M8x1.25)(79), and ARC WASHERS(M8)(80). STEP 3 Attach the FRONT STABILIZER(5) to the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x65mm) (62), ACORN NUTS(M8x1.25)(79), and ARC WASHERS(M8)(80).
A.
8
ASSEMBLY INSTRUCTIONS
STEP 4 Attach the SEAT(39) to the SEAT POST(6) with BUTTON HEAD BOLTS(M8x1.25x20)(67) and WASHERS (M8)(81). Insert the SEAT POST(6) into the MAIN FRAME(1) and secure with the ADJUSTMENT KNOB(36). NOTE: 1. Make sure that the pin on the ADJUSTMENT KNOB(36) is inserted into one of the holes in the
SEAT POST(6). 2. The ADJUSTMENT KNOB(36) should be screwed in tight to make the SEAT POST(6) fit securely
in the MAIN FRAME(1). STEP 5 Attach the BACK FRAME(7) to the SEAT POST(6) with CARRIAGE BOLTS(M8x1.25x48mm)(65), NYLOCK NUTS(M8x1.25)(82), and WASHERS(M8)(81). STEP 6 Attach the HANDRAIL(8) to the BACK FRAME(7) with BUTTON HEAD BOLTS(M8x1.25x40mm)(64) and ARC WASHERS(M8)(80). STEP 7 Attach the BACK CUSHION(40) to the BACK FRAME(7) with BUTTON HEAD BOLTS(M8x1.25x20)(67) and WASHERS(M8)(81).
9
ASSEMBLY INSTRUCTIONS
STEP 8 Refer to the detail view. Attach the DESKTOP POST(4) to the DESKTOP(21) with BUTTON HEAD BOLTS(M8x1.25x12mm)(71) and WASHERS(M8)(81). STEP 9 Insert the DESKTOP POST(4) into the UPRIGHT(3) and secure with the ADJUSTMENT KNOB(36). Bolt the ROUND HEAD BOLT(M6x1x12mm)(74) into the UPRIGHT(3) for security. NOTE: Make sure that the pin on the ADJUSTMENT KNOB(36) is inserted into one of the holes in the
DESKTOP POST(4). The ADJUSTMENT KNOB(36) should be screwed in tight to make the DESKTOP POST(4) fit securely in the UPRIGHT(3).
10
ASSEMBLY INSTRUCTIONS
STEP 10 Refer to illustration B. Screw the SOCKET HEAD BOLT(M6x1x12mm)(76) into the inner side of the LEFT RESISTANCE ARM(35). STEP 11 Assemble the RESISTANCE ARMS(35, 66) by attaching the ARM BRACKET(9) to the BACK FRAME(7) with SOCKET HEAD BOLTS(M8x1.25x15mm)(77) and LOCK WASHERS(M8)(90). Screw the ADJUSTMENT PIN(29) into the ARM BRACKET(9), and make sure the pin is inserted into one of the adjustment holes in the RIGHT RESISTANCE ARMS(66). The angle between two RESISTANCE ARMS(35, 66) is adjustable by inserting the ADJUSTMENT PIN(29) into a different adjustment hole. Pull the ball knob of the ADJUSTMENT PIN(29) to adjust.
B.
11
ASSEMBLY INSTRUCTIONS
STEP 12 NOTE: The RIGHT PEDAL(52) has an R stamped on the end of the pedal shaft. The RIGHT PEDAL(52) has right hand threads and is tightened by turning clockwise. The LEFT PEDAL(43) has an L stamped on the end of the pedal shaft. The LEFT PEDAL(43) has left hand threads and is tightened by turning counterclockwise. Thread the RIGHT PEDAL(52) to the RIGHT CRANK(51) as shown. Tighten the pedal securely. The shoulder of the PEDALS(43, 52) should be in contact with the CRANKS(44, 51) when securely tightened. Select the RIGHT PEDAL STRAP(97) which has an R marked on the bottom side of the strap. Snap the three hole end to the inside edge of the RIGHT PEDAL(52). Snap the other end to the outside edge of the RIGHT PEDAL(52) with the R mark on the bottom of the RIGHT PEDAL STRAP(97). Select adjustment holes which allow your foot to be easily removed from the pedals. Repeat on the left side in order to attach the LEFT PEDAL(43) to the LEFT CRANK(44) and snap the LEFT PEDAL STRAP(96) to the LEFT PEDAL(43). STEP 13 Refer to the illustration and detail view. Pry the METER(19) from the DESKTOP(21). Install two AAA batteries into the METER(19), the batteries are not included. See page 14 for detailed battery installation instructions. Press the METER(19) back to the DESKTOP(21). Plug the CONNECTION WIRE(117) into the socket of the SENSOR WIRE(59) which located at the front of the UPRIGHT(3). STEP 14 Attach the HAND STRAPS(128) to TENSION CORDS(129, 130) with the HOOK(135) on both sides.
Shoulder
Shoulder
12
SET UP INSTRUCTIONS
Place the WirkTM Ride Workstation in the area where it will be used. It is recommended that the WirkTM Ride Workstation be placed on an equipment mat. The maximum operation dimensions of the WirkTM Ride Workstation are approximately 51.4 inches long x 50.4 inches wide x 61.2 inches tall. (These dimensions may vary up to one inch.) An area 6 feet wide x 6 feet long is required for safe operation of the WirkTM Ride Workstation. Make sure that adequate space is available for access to and passage around the WirkTM Ride Workstation.
LEVELING: Adjust the LEVELING CAPS(31) on the REAR STABILIZER(10) so that the WirkTM Ride Workstation sits on the floor without rocking.
MOVING: The WirkTM Ride Workstation has a pair of WHEELS(32) on the REAR STABILIZER(10). Adjust the RESISTANCE ARMS(35, 66) to the upright position. Hold the RESISTANCE ARMS(35, 66) and tilt back on WHEELS(32) to move the WirkTM Ride Workstation.
6 feet
6 feet
Equipment Mat (not included)
FUNCTION INSPECTION: Visually inspect the WirkTM Ride Workstation to verify that assembly is as shown in the above illustration. Check the function of the WirkTM Ride Workstation by turning the crank slowly through one complete revolution to verify that the drive train functions properly. Adjust the TENSION KNOB(57) and verify that it functions properly and the resistance changes.
CAUTION: Locate and read the CAUTION LABEL(103) on the WirkTM Ride Workstation. Make sure that all users read the CAUTION LABEL(103) before using the product.
13
OPERATIONAL INSTRUCTIONS
USING THE FITNESS METER
POWER ON : Pedal movement or press the button. POWER OFF : Automatically shuts off after four minutes of
inactivity.
MODE BUTTON: Press to select display functions, including SCAN, TIME, SPEED, DISTANCE, CALORIES, and ODOMETER. Press and hold for two seconds to reset all functions to zero, except ODOMETER.
SCAN TIME SPEED DISTANCE CALORIES ODO
MODE
FUNCTIONS:
SCAN: Automatically scans each function of TIME, SPEED, DISTANCE, CALORIES, and ODOMETER in sequence, display changes every six seconds. Press and release the button until the arrow appears on the display and points to the SCAN.
TIME: Displays the time from one second up to 99:59 minutes. SPEED: Displays the current speed from zero to 999.9 miles per hour. DISTANCE: Displays the distance from zero to 999.9 miles. CALORIES: Displays the calories burned from zero to 999.9 Kcal.
The calorie readout is an estimate for an average user. It should be used only as a comparison between workouts on this unit. ODOMETER: Displays the total accumulated distance you have traveled from zero to 9999 miles. The total accumulated distance is retained when the meter is turned off.
NOTE: 1. The meter will shut off automatically after four minutes of inactivity. All function values will be kept. Press the button and hold it down for two seconds to reset all functions to zero, except ODOMETER.
2. The ODOMETER will be reset to zero after batteries are removed for battery replacement or storage of the unit.
HOW TO INSTALL AND REPLACE BATTERIES:
1. Refer to illustration 1. Use hand or simple tool to pry the METER(19) from the DESKTOP(21).
2. The meter operates with two AAA batteries (1.5V each), the batteries are not included. Refer to the illustration 2 to install or replace the batteries.
3. Refer to the detail view in illustration 1. Press the METER(19) back to the DESKTOP(21).
1.
Tool
NOTE: 1. Do not mix a new battery with an old battery. 2. Use the same type of battery. Do not mix an alkaline battery with another type of battery. 3. Rechargeable batteries are not recommended. 4. Ultimate disposal of battery should be handled according to all state and federal laws and regulations. 5. Do not dispose of batteries in fire.
2. AAA Batteries
14
OPERATIONAL INSTRUCTIONS WEIGHT LIMITATIONS
WARNING: Serious injuries can occur from WirkTM Ride Workstation tip-over. To help prevent tip-over: Do not exceed listed weight limits Never allow children to climb or hang on the WirkTM Ride Workstation Do not lean on the desktop in any direction
15
OPERATIONAL INSTRUCTIONS
LOAD ADJUSTMENT
To increase the load, turn the TENSION KNOB(57) clockwise. To decrease the load, turn the TENSION KNOB(57) counterclockwise. There are eight levels for the load adjustment.
SEAT ADJUSTMENT
Proper seat adjustment is important. 1. Turn the ADJUSTMENT KNOB(36) to loosen, then pull
the ADJUSTMENT KNOB(36) to release the pin. Slide the SEAT POST(6) until the SEAT(39) is at the proper height. Release the ADJUSTMENT KNOB(36) making sure the pin catches in one of the holes of the SEAT POST(6) and tighten the ADJUSTMENT KNOB(36). 2. Sit on the seat and place your feet on the pedals. You should be able to move through a complete pedal stroke without locking your knees or shifting your hips on the seat. The seat is too close to the pedals if you have more than a slight bend in your knees at the bottom of the pedal stroke. The seat is too far from the pedals if you have to completely straighten your knees at the bottom of the pedal stroke. Refer to the illustration. CAUTION: 1. Do not attempt to adjust the seat while you are
on the WirkTM Ride Workstation. 2. Always tighten the ADJUSTMENT KNOB(36)
after adjusting the seat to a new position.
RESISTANCE ARM ADJUSTMENT
The angle between two RESISTANCE ARMS(35, 66) is adjustable. Pull the ADJUSTMENT PIN(29), then swing up or down the RESISTANCE ARMS(35, 66). Replace the ADJUSTMENT PIN(29) and lock in the desired position. NOTE: Make sure the pin of the ADJUSTMENT PIN(29) is
inserted into one of the adjustment holes in the RIGHT RESISTANCE ARMS(66).
16
OPERATIONAL INSTRUCTIONS DESKTOP ANGLE ADJUSTMENT
Refer to the illustrations below. The angle of the DESKTOP(21) can be set to different angles from Position 1 to Position 5. Lift the LEVER(55) up using your right foot, adjust the UPRIGHT(3)/DESKTOP(21) to desired position. Then press the LEVER(55) down to lock the UPRIGHT(3)/DESKTOP(21) in position.
5 4 3 2 Position 1
Position Index ( Shown 1 to 5 )
The WirkTM Ride Workstation can be used while sitting or standing. Refer to the illustrations below. Please always set the DESKTOP(21) at Position 1 for mounting or dismounting the WirkTM Ride Workstation. For sitting, you can adjust the DESKTOP(21) to other angles with the LEVER(55) after you are sitting on the bike. For using the DESKTOP(21) while standing, please keep the desktop in Position 1. NEVER USE THE PEDALS WHILE STANDING.
Position 1
17
OPERATIONAL INSTRUCTIONS
USING A TABLET ON THE DESKTOP
Refer to the illustration below. Set the TABLET HOLDER(18) with an angle and use the TABLET HOLDER SUPPORT(20) to support the TABLET HOLDER(18) from the back. Place your tablet device on the TABLET HOLDER(18).
USING A LAPTOP COMPUTER ON THE DESKTOP
Refer to the illustration below. Place your laptop computer on the DESKTOP(21). Use the STRAP(61) to secure the laptop as shown in details view 1 and 2. 1. Refer to detail view 1. Run the STRAP(61) through the two D Rings. 2. Refer to detail view 2. Run the STRAP(61) into the gap between the two D Rings, then go through the
D Ring at the bottom. Pull the STRAP(61) tighten to secure the laptop.
Laptop Computer
2. 1.
18
STORAGE
1. Remove all items from the DESKTOP(21) before moving or folding the WirkTM Ride Workstation. 2. To store the WirkTM Ride Workstation, simply keep it in a clean dry place. 3. To avoid damage to the electronics, remove the batteries before storing the WirkTM Ride Workstation
for one year or more. 4. To move the WirkTM Ride Workstation, hold the HANDRAIL(8) and tilt the WirkTM Ride Workstation
onto the WHEELS(32) of the REAR STABILIZER(10). 5. The minimum folded dimensions of the WirkTM Ride Workstation are approximately 36.1 inches
long x 29.9 inches wide x 66.1 inches tall. Please measure your WirkTM Ride Workstation if exact dimensions are needed.
a. Pull the ADJUSTMENT PIN(29) to swing up the RESISTANCE ARMS(35, 66). Replace the ADJUSTMENT PIN(29) and lock in place. Use the LEVER(55) to adjust the UPRIGHT(3) backward to Position 5.
b. Remove the PULL PIN(49) from the REAR FRAME(2). Fold the REAR FRAME(2) close to the MAIN FRAME(1) and lock it in folded position with the PULL PIN(49). NOTE: Make sure the PULL PIN(49) goes through the holes on both sides of the REAR FRAME(2) and the tube on the MAIN FRAME(1).
A
B
MAINTENANCE
The safety and integrity designed into the WirkTM Ride Workstation can only be maintained when the WirkTM Ride Workstation is regularly examined for damage and wear. Special attention should be given to the following:
1. Adjust the TENSION KNOB(57) and verify that it functions properly and the resistance changes. 2. Use a wrench to verify that the pedals are tightened securely. If tightening is required, remember that
the left pedal has left hand threads and is tightened by turning counterclockwise. 3. Verify that all nuts and bolts are present and properly tightened. Replace missing nuts and bolts.
Tighten loose nuts and bolts. 4. Verify that the CAUTION LABEL(103) is in place and easy to read. Call Stamina Products
immediately at 1-800-375-7520 for a replacement CAUTION LABEL(103) if it is missing or damaged. 5. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed. 6. Worn or damaged components must be replaced immediately or the WirkTM Ride Workstation
removed from service until repair is made. 7. Only Stamina Products supplied components should be used to maintain/repair the WirkTM Ride
Workstation. 8. Keep your WirkTM Ride Workstation clean by wiping it off with an absorbent cloth after use.
19
CONDITIONING GUIDELINES
How you begin your exercise program depends on your physical condition. If you have been inactive for several years or are severely overweight, start slowly and increase your workout time gradually. Increase your workout intensity gradually by monitoring your heart rate while you exercise.
Remember to follow these essentials: Have your doctor review your training and diet programs. Begin your training program slowly with realistic goals that have been set by you and your physician. Warm up before you exercise and cool down after you work out. Take your pulse periodically during your workout and strive to stay within a range of 60% (lower intensity) to 90% (higher intensity) of your maximum heart rate zone. Start at the lower intensity, and build up to higher intensity as you become more aerobically fit. If you feel dizzy or lightheaded you should slow down or stop exercising.
Initially you may only be able to exercise within your target zone for a few minutes; however, your aerobic capacity will improve over the next six to eight weeks. It is important to pace yourself while you exercise so you don't tire too quickly.
To determine if you are working out at the correct intensity, use a heart rate monitor or use the table below. For effective aerobic exercise, your heart rate should be maintained at a level between 60% and 90% of your maximum heart rate. If just starting an exercise program, work out at the low end of your target heart rate zone. As your aerobic capacity improves, gradually increase the intensity of your workout by increasing your heart rate.
Measure your heart rate periodically during your workout by stopping the exercise but continuing to move your legs or walk around. Place two or three fingers on your wrist and take a six second heartbeat count. Multiply the results by ten to find your heart rate. For example, if your six second heartbeat count is 14, your heart rate is 140 beats per minute. A six second count is used because your heart rate will drop rapidly when you stop exercising. Adjust the intensity of your exercise until your heart rate is at the proper level.
wrist pulse
Target Heart Rate Zone Estimated by Age*
Age
20 years 25 years 30 years 35 years 40 years 45 years 50 years 55 years 60 years 65 years 70 years
Target Heart Rate Zone (55%-90% of Maximum Heart Rate)
110-180 beats per minute 107-175 beats per minute 105-171 beats per minute 102-166 beats per minute
99-162 beats per minute 97-157 beats per minute 94-153 beats per minute 91-148 beats per minute 88-144 beats per minute 85-139 beats per minute 83-135 beats per minute
Average Maximum Heart Rate 100% 200 beats per minute 195 beats per minute 190 beats per minute 185 beats per minute 180 beats per minute 175 beats per minute 170 beats per minute 165 beats per minute 160 beats per minute 155 beats per minute 150 beats per minute
* For cardiorespiratory training benefits, the American College of Sports Medicine recommends working out within a heart rate range of 55% to 90% of maximum heart rate. To predict the maximum heart rate, the following formula was used: 220 - Age = predicted maximum heart rate
20
WARM-UP and COOL-DOWN
Warm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles. Activities may include brisk walking, jogging, jumping jacks, jump rope, and running in place.
Stretching Stretching while your muscles are warm after a proper warm-up and again after your strength or aerobic training session is very important. Muscles stretch more easily at these times because of their elevated temperature, which greatly reduces the risk of injury. Stretches should be held for 15 to 30 seconds. Do not bounce.
Suggested Stretching Exercises
Lower Body Stretch Place feet shoulder-width apart and lean forward. Keep this position for 30 seconds using the body as a natural weight to stretch the backs of the legs. DO NOT BOUNCE! When the pull on the back of the legs lessens, gradually try a lower position.
Bent Torso Pulls While sitting on the floor, have legs apart, one leg straight and one knee bent. Pull the chest down to touch the thigh on the leg that is bent, and twist at the waist. Hold this position at least 10 seconds. Repeat 10 times on each side.
Floor Stretch While sitting on the floor, open the legs as wide as possible. Stretch the upper body toward the knee on the right leg by using your arms to pull your chest to your thighs. Hold this stretch 10 to 30 seconds. DO NOT BOUNCE! Do this stretch 10 times. Repeat the stretch with the left leg.
Bent Over Leg Stretch Stand with feet shoulderwidth apart and lean forward as illustrated. Using the arms, gently pull the upper body towards the right leg. Let the head hang down. DO NOT BOUNCE! Hold the position a minimum of 10 seconds. Repeat pulling the upper body to the left leg. Do this stretch several times slowly.
Remember to always check with your physician before starting any exercise program.
Cool-Down The purpose of cooling down is to return the body to its normal, or near normal, resting state at the end of each exercise session. A proper cool-down slowly lowers your heart rate and allows blood to return to the heart. Your cool-down should include the stretches listed above and should be completed after each strength training session.
21
PRODUCT PARTS DRAWING FRONT
BACK
22
PARTS LIST
PART#
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
PART NAME
Main Frame Rear Frame Upright Table Post Front Stabilizer Seat Post Back Frame Handrail Arm Bracket Rear Stabilizer Left Cover Right Cover Top Cover Left Front Cover Right Front Cover Lever Cover Hollow Cap Tablet Holder Meter Tablet Holder Support Desktop Bottom Cap Sensor Clip Bearing Housing Bushing Bolt, Round Head (M6 x 1 x 25mm) Plastic Bushing Oval Plug (20mm x 40mm) Adjustment Pin Protection Pad Leveling Cap Wheel Round Plug (25mm) Square Plug (30mm x 30mm) Left Resistance Arm Adjustment Knob Crank Cap Bumper Seat Back Cushion Foam Grip Shaft Left Pedal Left Crank Bolt, Button Head (M6 x 1 x 55mm) V-Ribbed Belt (230J) V-Ribbed Belt (240J) Pulley w/ Shaft Pull Pin Bearing Housing Cover
23
QTY
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 2 1 4 6 2 1 1 2 2 2 1 1 2 2 1 1 1 2 1 1 1 2 1 1 1 1 2
PARTS LIST
PART#
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
PART NAME
Right Crank Right Pedal Pulley Shaft Pulley Lever Bolt, Button Head (M6 x 1 x 42mm) Tension Knob Spring Sensor Wire Washer (M6) Strap Carriage Bolt (M8 x 1.25 x 65mm) Bolt, Hex Head (M6 x 1 x 45mm) Bolt, Button Head (M8 x 1.25 x 40mm) Carriage Bolt (M8 x 1.25 x 48mm) Right Resistance Arm Bolt, Button Head (M8 x 1.25 x 20mm) Eye Bolt (M6 x 1) Bolt, Button Head (M8 x 1.25 x 55mm) Bolt, Button Head (M8 x 1.25 x 68mm) Bolt, Button Head (M8 x 1.25 x 12mm) Screw, Round Head (M4.2 x 16mm) Screw, Round Head (M5 x 20mm) Bolt, Round Head (M6 x 1 x 12mm) Screw, Round Head (M5 X 0.8 x 55mm) Bolt, Socket Head (M6 x 1 x 12mm) Bolt, Socket Head (M8 x 1.25 x 15mm) Flange Nut (M10 x 1.25) Acorn Nut (M8 x 1.25) Arc Washer (M8) Washer (M8) Nylock Nut (M8 x 1.25) Nut (M10 x 1.25 x 8.3mm thick) Tension Bracket Nylock Nut (M6 x 1) C Ring (17mm) Ball Bearing (6003RS) C Ring (10mm) Bolt, Pan Round Head (M6 x 1 x 10mm) Lock Washer (M8) Endcap Large Washer (ø8.2 x ø25 x 2mm Thick) Magnet Nut (M10 x 1.25 x 5mm thick) Screw, Round Head (M4 x 0.6 x 10mm) Left Pedal Strap Right Pedal Strap Nylock Nut (M10 x 1.5) Bolt, Button Head (M8 x 1.25 x 42mm) Idler Shaft
24
QTY
1 1 1 1 1 2 1 1 1 4 1 4 2 2 2 1 9 2 2 1 3 17 4 2 1 1 2 2 4 6 16 7 2 2 6 6 2 1 2 7 2 2 1 1 1 1 1 1 2 1
PARTS LIST
PART#
101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137
PART NAME
Ball Bearing (6202RS) Bolt, Round Head (M6 x 1 x 10mm) Caution Label Coaster Combination Wrench Allen Wrench (5mm) w/ Screwdriver Manual Magnetic Disc Magnetic Brake Ball Bearing (6000ZZ) Wave Washer (S10) Wave Washer (S17) Lock Washer (M10) Sleeve Arm Endcap Guide Block Connection Wire Screw, Round Head (M4.2 x 25mm) Plastic Washer Thin Nylock Nut (M8 x 1.25) Nut (M6 x 1) Screw, Round Head (M4 x 10mm) Wire Clip Pulley Holder Pulley Tension Knob Holder Washer (M5) Hand Strap Heavy Tension Cord (green color) Tension Cord (gray color) Bushing Spacer Retaining Plug Bolt, Socket Flat Head (M8 x 1.25 x 58mm) C Ring (15mm) Hook Allen Wrench (6mm) Serial Decal
QTY
1 8 1 1 1 1 1 1 1 2 2 1 1 1 2 1 1 2 2 2 2 2 2 2 8 1 1 2 2 2 4 1 2 1 2 1 1
25
LIMITED WARRANTY
MODEL 85-2449
WARRANTY
Stamina Products, Inc. ("Stamina") warrants to the original purchaser that this product will be free from defects in materials and workmanship that arise under normal use, service, proper assembly and proper operation in accordance with product warnings/instructions for a period of 90 days on the parts and three years on the frame from the date of the original purchase from an authorized retailer. THIS WARRANTY SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO COMMERCIAL USE, ABUSE, MISUSE, ALTERATION OF ANY KIND OR TO ANY DEFECT OR CHANGE CAUSED BY IMPROPER ASSEMBLY, REPAIR, REPLACEMENT, SUBSTITUTION OR USE WITH PARTS NOT PROVIDED BY STAMINA. Commercial use includes use of product in athletic clubs, health clubs, spas, gyms, and all other public or semipublic facilities whether or not the product's use is in furtherance of a profit making enterprise, and all other use which is not for personal purposes.
To implement this limited warranty, send a written notice stating your name, date, and place of purchase and a brief description of the defect along with your receipt to Stamina Products, Inc. 2040 N Alliance Ave, Springfield, Missouri, USA, MO 65803, or email us at customer.care@staminaproducts.com, or call us at 1-800-375-7520. If the defect is covered under this limited warranty, you will be requested to return the product or part to us for free repair or replacement at our option.
NO ACTION FOR BREACH OF THIS LIMITED WARRANTY MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER THE DATE THE ALLEGED BREACH WAS OR SHOULD HAVE BEEN DISCOVERED. NO ACTION FOR BREACH OF ANY IMPLIED WARRANTY (INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) MAY BE COMMENCED MORE THAN ONE (1) YEAR AFTER DELIVERY OF THE PRODUCT TO THE PURCHASER. These warranties are not transferable. IF ANY PART OF THE PRODUCT IS NOT IN COMPLIANCE WITH THIS LIMITED WARRANTY OR ANY IMPLIED WARRANTY, THE REMEDY OF REPAIR OR REPLACEMENT IS THE EXCLUSIVE REMEDY. If any claim is made under this limited warranty or any implied warranty, Stamina reserves the right to require the product to be returned for inspection, at the purchaser's expense, to Stamina's premises in Springfield, Missouri. Return of the enclosed warranty registration card is not required for warranty coverage, but is merely a way of establishing the date and place of purchase.
Stamina SHALL NOT BE LIABLE FOR THE LOSS OF USE OF ANY PRODUCT, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS OR ANY OTHER INDIRECT, CONSEQUENTIAL, SPECIAL OR INCIDENTAL DAMAGES DUE TO BREACH OF THE ABOVE WARRANTY OR ANY IMPLIED WARRANTY.
THIS LIMITED WARRANTY IS THE ONLY EXPRESS WARRANTY. NO ORAL OR WRITTEN INFORMATION GIVEN BY STAMINA, ITS AGENTS OR EMPLOYEES, SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY. This warranty gives you specific legal rights, and you may also have other legal rights which vary from state to state. ANY OTHER RIGHT WHICH YOU MAY HAVE, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
The laws in some states affect the disclaimer or limitation of implied warranties and consequential and incidental damages. If any such law is found applicable, the foregoing disclaimers and limitations of and on implied warranties and consequential and incidental damages shall be deemed to be modified to the extent necessary to comply with applicable law.
26
Coaster Toss
On the bottom of the WIRK Ride Workstation box, you'll notice a point system for the WIRK Coaster Toss. Use the included WIRK coaster to hold your coffee cup, water, iced pomegranate lemonade, or to play COASTER TOSS!!!
Rules:
One player at a time will toss the coaster from a predetermined distance to the box, attempting to land the coaster onto the box. We recommend 3 paces, but the distance for your game is up to you. Choose tossing order by drawing straws, flipping a coin, playing paper-rock-scissors, alphabetical by last name, shoe size, etc.
Points are determined by the section of the box where the coaster comes to rest. If the coaster lies between two sections, the player is awarded the points where the majority of the coaster lies (i.e. if more than half of the coaster is in the 30 point section, player is awarded 30 points). No points are earned if the coaster falls off the box.
First player to earn 100 or more points wins. Every player shall get an equal number of tosses. For example, if player 1 reaches 100 points in 5 tosses, the other players shall get to toss their fifth attempt if they are within tying range. The winner is determined by the player who has the highest score over 100 at the end of the round.
In the event of a tie, a one toss tiebreaker shall be held between the players. The player with the highest one toss score will be the winner. Tiebreaker toss shall be repeated until a winner is determined.
The winner shall be rewarded with a prize of the group's choosing. We suggest ownership of the WIRK Coaster until the game is played again.
27
NOTES
28
NOTES
29
TO CONTACT CUSTOMER CARE
For your convenience, Stamina's customer care representatives can be reached by email at customer.care@staminaproducts. com or by phone at 1-800-375-7520 (in the U.S.). Our customer care representatives are available Monday through Thursday from 7:30 a.m. until 5:00 p.m., and Friday 8:00 a.m. until 3 p.m. Central Time.
ONLINE CUSTOMER CARE customer.care@staminaproducts.com www.staminaproducts.com
TELEPHONE CUSTOMER CARE Tel: 1 (800) 375-7520
FAX CUSTOMER CARE Fax: (417) 889-8064
MAIL STAMINA PRODUCTS, INC.
ATTN: Customer Care 2040 N Alliance Ave, Springfield, MO 65803
Would you like to recieve email information or special offers from Stamina Products? Register at contact.staminaproducts.com
TO REGISTER YOUR PRODUCT
To enact your warranty, please register your product by going to register.staminaproducts.com. Please have your product model number (printed on the cover of this owner's manual) and the serial number (printed on the black and white sticker on your product) ready.
If you don't have internet access, you can call customer care at 1-800-375-7520, or fill out and mail the product registration form below to Stamina Products, Inc.; 2040 N Alliance Ave, Springfield, MO 65803.
PRODUCT REGISTRATION FORM
Stamina Products, Inc. 2040 N Alliance Ave, Springfield, MO 65803
Model Number: ......................................................................................
Serial Number: .............................................................................................
Product Name: ..................................................................................................................................................................................................................................
Place Purchased: ..............................................................................................................................................................................................................................
Date of Purchase: ..................................................................................
Purchase Price: ............................................................................................
First Name: ............................................................................................
Last Name: ...................................................................................................
City: ..................................................................
State: ................................................................
Zip Code: .................................................
Email Address: .......................................................................................
Phone #: (
) ......................................................................................
Would you like to receive email information or special offers from Stamina Products?* ____Yes ____No *If yes, be sure your email address is included above.
Detach and Mail or Fax the Form Above
TO ORDER PARTS
If there are missing or damaged parts, you can go to parts.staminaproducts.com and order those parts. If you have questions, please contact customer care. Do not return the product. To order parts by mail, fill out the sheet below and fax it to 417-889-8064. The part will be mailed to your address.
Detach and Mail or Fax the Form Below
PARTS ORDER FORM
Stamina Products, Inc. 2040 N Alliance Ave, Springfield, MO 65803
Mr./Ms: ..............................................................................................................................................................................................................................................
Address: ........................................ .............................................................................................
Apt. #:..........................................................................
City: ..................................................................
State: ................................................................
Zip Code: .................................................
IMPORTANT : We require your phone number to process the order!
Phone #: (
) ................................................................................
Work Phone #: (
) .............................................................................
Date of Purchase: ..................................................................................
Model #: ............................................................................................................................................................................................................................................
Purchased From: ..............................................................................................................................................................................................................................
IMPORTANT: Before filling out the portion below, make sure you have the correct information. Refer to the parts list to make sure you're ordering the right parts!
PART #
EXAMPLE:
1
DESCRIPTION Rear Unit Assembly
QUANTITY 1
Adobe PDF Library 11.0 Adobe InDesign CC 2014 (Windows)