Instructions for dams models including: dams, DHBC, Desk High Bookcase
Toole Required SHELF ILH SIDEI IBASEI Dia 38mm Foot -T•Nut OOCMNMI04 I 012-01-026---4 ..,,4 't@ Quick fix pin 012-o1-o89 Quantity: 10 C8m15N 111-41M21ij Quantity: 10
DHBC
DESK HIGH BOOKCASE
01 JUNE08
ILH SIDEI
SHELF
IRHSIDEI
IBASEI
Toole Required
Dia 38mmFoot
OOCMNMI0
I
- T·Nut 012-01-026
't@
---4 _..,, 4
ij Quick fix pin
C8m15N
012-o1-o89 111-41M21
Tlluepln 011-01-014
Quantity: 8 Tltuabung 011-01-013
Quantity: 10 Quantity: 10
Quantity:&
Conflnnat acrew 50 111-22-087
PAGE01
DPDHD
Desk High Door Pack
22.01.2018
1
1
PHILLIPS ( PH2 ) OR POZI ( PZ2 ) SCREWDRIVER
1,2,3...
2
KEEP FITTINGS AWAY FROM CHILDREN
IF UNSURE CALL FOR ASSISTANCE
ALWAYS HANDLE ITEMS WITH CARE
DONT STRUGGLE 2 MAN LIFT
TOOLS REQUIRED FOR ASSEMBLY
Please check that you have all the panels!
1DHDPD
RM-DOR066 LH DOOR PANEL
RM-DOR067 RH DOOR PANEL
Please check that you have all the fittings!
1DHDPD
110' Clip On - Soft Close Hinge RM-HGE011
4
Door Lock RM-LOK11
1
Clip On Hinge Plate RM-HGP011
4
Door Latch RM-LOK13
1
96mm Bow Handle RM-HDL009
2
Door Clip RM-LOK12
1
1
Step 1
4x
Place the hinges into
the pre drilled holes
on the inside face of
each door panel.
M4x22mm Handle Screw RM-SCR25
4
3.5x15mm Wood Screw RM-SCR26
10
4.0 X 20mm Wood Screw RM-SCR37
4
2
Step 2 Attach the hinges
8x
using the 3.5 x 15mm
wood screws, 2
screws per hinge.
3
3
Step 3 Attach the hinge plates to the pre drilled holes on the inside face of the bookcase side panels, these plates are fitted with pre attached screws. Ensure the plate is fitted as per diagram 1.
4x
4
Step 4 Attach both doors to the bookcase. Diagrams 2 & 3 show how to lock the hinge to the plate. Always lock the top hinge into place first before repeating for all hinges.
5
Step 5 Attach handles to both doors using the M4x22 screws.
2x
4x
4
Diagram 1
Ensure the hook of the hinge locates into the hinge plate.
Diagram 2
Fasten the hinge to the plate by applying pressure here.
Diagram 3
EDGE OF BOOKCASE
6
Step 6 Insert the lock into the back face of the RH door, the rosette should be place over the exposed lock barrel on the front face of the door.
Align the lock with the edge of the door as shown in diagram 4.
Fix the lock in place using two of the 4x20mm wood screws.
1x
2x
7
Step 7 Attach the door latch to the rear face of the LH door.
See diagram 5 for fixing position to be used for both standard double door or combination units.
Fix the lock in place using the remaining x 4x20mm wood screws.
1x
2x
8
Step 8 Attach the latch strike plate to the underside of the bookcase top.
This should be fitted to the 2 pre drilled holes and aligned with the front edge of the bookcase top as shown in diagram 6.
1x
2x
EDGE OF DOOR
DIAGRAM 4
STANDARD CUPBOARD DIAGRAM 5
EDGE OF TOP
DIAGRAM 6
5
EDGE OF DOOR
DOOR ADJUSMENT AND ALIGNMENT
A
B C
AB-
SIDE ADJUSTMENT HEIGHT ADJUSTMENT
C - DEPTH ADJUSTMENT
D B
D - DOOR RELEASE BUTTON
TO ADJUST THE GAP BETWEEN DOORS Apply equal adjustment to point A on all hinges.
Tighten to make the gap smaller. Loosen to make the gap larger.
TO RE ALIGN SKEWED DOORS Adjust point A on individual hinges to re align accordingly. Tightening the top hinges will rotate the door clockwise. Tightening the bottom hinges will rotate the door anti-clockwise.
TO ADJUST THE GAP BETWEEN DOOR AND TOP Loosen all point B screws without removing them.
Once loose lift the door to close any gap. Whilst the door is held in its preferred position
re tighten all point B screws again.
TO ADJUST THE GAP BETWEEN DOOR AND SIDE PANEL Loosen point C screws on all hinges.
Slide the hinge to your preferred position and re tighten point C screws.
TO COMPLETELY REMOVE DOORS ACTIVATE BUTTON D ON ALL HINGES
6
POWER TOOLS SHOULD NEVER BE USED FOR ANY ADJUSTMENTS